Precision 7750 Service Manual Regulatory Model: P44E Regulatory Type: P44E001 May 2020 Rev.
メモ、注意、警告 メモ: 製品を使いやすくするための重要な情報を説明しています。 注意: ハードウェアの損傷やデータの損失の可能性を示し、その危険を回避するための方法を説明しています。 警告: 物的損害、けが、または死亡の原因となる可能性があることを示しています。 © 2020 年 Dell Inc.またはその子会社。不許複製・禁無断転載。Dell、EMC、およびその他の商標は、Dell Inc.
Contents 1 コンピュータ内部の作業................................................................................................................. 6 安全にお使いいただくために........................................................................................................................................... 6 コンピュータ内部の作業を始める前に..................................................................................................................... 6 安全に関する注意事項........................................................................
Removing the WLAN card............................................................................................................................................34 Installing the WLAN card.............................................................................................................................................. 35 WWAN カード.....................................................................................................................................................................
GPU カード.......................................................................................................................................................................... 68 GPU カードの取り外し............................................................................................................................................... 68 GPU カードの取り付け............................................................................................................................................... 69 スピーカー........
1 コンピュータ内部の作業 安全にお使いいただくために 前提条件 身体の安全を守り、PC を損傷から保護するために、次の安全に関する注意に従ってください。特記がない限り、本書に記載され る各手順は、以下の条件を満たしていることを前提とします。 • • PC に付属の「安全に関する情報」を読んでいること。 コンポーネントは交換可能であり、別売りの場合は取り外しの手順を逆順に実行すれば、取り付け可能であること。 このタスクについて メモ: コンピューターのカバーまたはパネルを開ける前に、すべての電源を外してください。コンピュータ内部の作業が終わ ったら、カバー、パネル、ネジをすべて取り付けてから、電源に接続します。 警告: PC 内部の作業を始める前に、お使いの PC に付属しているガイドの安全にお使いいただくための注意事項をお読みく ださい。その他、安全にお使いいただくためのベストプラクティスについては、法令遵守のホームページを参照してくださ い。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サー
注意: ネットワークケーブルを外すには、まずケーブルのプラグをコンピュータから外し、次にケーブルをネットワークデ バイスから外します。 5. コンピュータおよび取り付けられているすべてのデバイスをコンセントから外します。 6.
• • • • 適切に接地された、有線の ESD リストバンドを使用します。ワイヤレスの静電気防止用リストバンドの使用は、現在許可され ていません。これらのリストバンドでは、適切な保護がなされません。パーツの取り扱い前にシャーシに触れる方法では、感 度が増したパーツを ESD から十分に保護することができません。 静電気の影響を受けやすいすべてのコンポーネントは、静電気のない場所で扱います。可能であれば、静電気防止フロアパッ ドおよび作業台パッドを使用します。 静電気の影響を受けやすいコンポーネントを輸送用段ボールから取り出す場合は、コンポーネントを取り付ける準備ができる まで、静電気防止梱包材から取り出さないでください。静電気防止パッケージを開ける前に、必ず身体から静電気を放出して ください。 静電気の影響を受けやすいコンポーネントを輸送する場合は、あらかじめ静電気防止コンテナまたは静電気防止パッケージに 格納します。 ESD フィールド・サービス・キット 最も頻繁に使用されるサービスキットは、監視されないフィールド・サービス・キットです。各フィールド・サービス・キットは、静 電対策マット、リストス
PC 内部の作業を終えた後に このタスクについて 取り付け手順が完了したら、コンピュータの電源を入れる前に、外付けデバイス、カード、ケーブルが接続されていることを確認 してください。 手順 1. 電話線、またはネットワーク ケーブルをコンピュータに接続します。 注意: ネットワーク ケーブルを接続するには、まずケーブルをネットワークデバイスに差し込み、次に、コンピュータに差 し込みます。 2. PC、および取り付けられているすべてのデバイスをコンセントに接続します。 3. PC の電源を入れます。 4.
2 テクノロジとコンポーネント この章には、システムで使用可能なテクノロジーとコンポーネントの詳細が掲載されています。 トピック: USB の機能 USB Type-C HDMI 2.0 NVIDIA Quadro T1000 NVIDIA Quadro RTX3000 NVIDIA Quadro RTX4000 NVIDIA Quadro RTX5000 • • • • • • • USB の機能 USB(ユニバーサル シリアル バス)は 1996 年に導入されました。これにより、ホスト PC と周辺機器類(マウス、キーボード、 外付けドライバ、プリンタなど)との接続が大幅にシンプルになりました。 表 1. USB の進化 タイプ データ転送速度 カテゴリ 導入された年 USB 2.0 480 Mbps 高速 2000 USB 3.2 Gen 1(以前 は USB 3.0/USB 3.1 Gen 1) 5 Gbps SuperSpeed 2010 USB 3.1 Gen 2 10 Gbps SuperSpeed Plus 2013 USB 3.
ン 3.1 以降)に分類されます。新しい SuperSpeed+モードの転送速度は 20Gbps です。USB 3.2 標準は、USB 3.1/3.0 および USB 2.0 と後方互換性があります。 USB 3.2 Gen 1 は、次の技術変更によってパフォーマンスをさらに向上させています。 • • • 既存の USB 2.0 バスと並行して追加された物理バス(次の図を参照)。 USB 2.0 にあった(電源、接地、および差分データ用の 1 組)4 本のワイヤに、USB 3.1 Gen 1 では 2 組の差分信号(送受信)用 がさらに 4 本追加され、合計 8 本になったコネクターとケーブル接続。 USB 3.2 Gen 1 では、USB 2.0 のハーフ デュプレックス配置ではなく双方向データ インターフェイスを使用します。これによ り、帯域幅が理論的に 10 倍に増加します。 用途 USB 3.
これにより、独自のノートパソコン充電ケーブルは必要なくなり、標準 USB 接続ですべて充電できます。今日からは、スマートフ ォンやその他のポータブル デバイスを充電しているポータブル バッテリ パックの 1 つを使ってノートパソコンを充電できます。 ノートパソコンを電源ケーブルに接続された外部ディスプレイにつなぐと、使用している間にその外部ディスプレイによってノー トパソコンが充電されます。すべては小さな USB Type-C 接続を介して行われます。これを使用するには、デバイスとケーブルが USB Power Delivery をサポートしている必要があります。USB Type-C 接続があるだけで、必ず充電できるという意味ではありま せん。 USB Type-C および USB 3.2 USB 3.2 は、新しい USB 規格です。USB 3 の理論上の帯域幅は 5 Gbps で、USB 3.2 は 20 Gbps です。つまり帯域幅は第 1 世代の Thunderbolt コネクターの 2 倍の速さです。USB Type-C は USB 3.
メモ: データ転送速度はデバイスによって異なります。 Thunderbolt アイコン 図 2. Thunderbolt アイコンのバリエーション HDMI 2.0 このトピックでは、ハイデフィニション マルチメディア インターフェイス(HDMI)2.0 とその機能について利点と合わせて説明 します。 HDMI は、業界から支持される非圧縮、全デジタル オーディオ/ビデオ インターフェイスです。HDMI は、DVD プレーヤーや A/V レシーバーなどの互換性のあるデジタルオーディオ / ビデオソースと、デジタル TV(DTV)などの互換性のあるデジタルオーディ オ / ビデオモニタ間のインタフェースを提供します。HDMI の対象とされる用途はテレビおよび DVD プレーヤーです。主な利点 は、ケーブルの削減とコンテンツ保護プロビジョニングです。HDMI は、標準、拡張、または高解像度ビデオと、単一ケーブル上 のマルチチャンネルデジタルオーディオをサポートします。 HDMI 2.
NVIDIA Quadro T1000 表 2. NVIDIA Quadro T1000 特長 値 グラフィックス メモリ 4 GB コア 768 メモリ帯域幅 128 Gbps メモリーのタイプ GDDR6 メモリー インターフェイス 128 ビット クロック速度 1395~1455(ブースト)MHz GPU ベース クロック 8000 MHz(P0 で最小) 推定最大電源 50 W ディスプレイ サポート eDP/mDP/HDMI/Type-C 最大色深度 最大 10 ビット/色 オペレーティング システムのグラフィックス/ビデオ API サポ ート DirectX 12.0、OpenGL 4.6、DisplayPort 1.4、DirectX 12.1 サポートされている解像度および最大リフレッシュレート (Hz) • • ディスプレイ サポートの数 最大デジタル:シングル DisplayPort 1.4:7680 x 4320 (8K)@ 30 Hz(mDP/Type-C to DP) 最大デジタル:デュアル DisplayPort 1.
表 3. NVIDIA Quadro RTX3000(続き) 特長 値 • ディスプレイ サポートの数 最大デジタル:デュアル DisplayPort 1.4:7680 x 4320 (8K)@ 60 Hz(mDP/Type-C to DP) 最大 4 台のディスプレイ NVIDIA Quadro RTX4000 Table 4.
Table 5. NVIDIA Quadro RTX5000(continued) Feature Values Maximum Color Depth Up to 10 bit/color Operating Systems Graphics/ Video API Support DirectX 12.0, OpenGL 4.6, DisplayPort 1.4, DirectX 12.1 Supported Resolutions and Max Refresh Rates (Hz) • • Numbers of Display Support 16 テクノロジとコンポーネント Max Digital : Single DisplayPort 1.4 - 7680 x 4320 (8k) @ 30 Hz (mDP/Type-C to DP) Max Digital : Dual DisplayPort 1.
3 分解および再アセンブリ SD カード SD カードの取り外し 前提条件 1. PC 内部の作業を始める前にの手順に従います。 このタスクについて 図は SD カードの位置を示すもので、取り外し手順を視覚的に表しています。次のレビュー サイクルでアップロードされる画像で す。 手順 1. SD カードを押し込んで、コンピュータから外します。 2. SD カードをコンピュータから引き出します。 SD カードの取り付け 前提条件 コンポーネントを交換する場合、取り付け手順を実行する前に、既存のコンポーネントを取り外してください。 このタスクについて 図はベース カバーの場所を示すもので、取り付け手順を視覚的に表しています。 次のレビュー サイクルでアップロードされる画像です。 手順 カチッと所定の位置に収まるまで、SD カードを PC のスロットに差し込みます。 次の手順 1. 「PC 内部の作業を終えた後に」の手順に従います。 SSD ドア Removing SSD door Prerequisites 1.
Steps 1. Push the SSD door towards left side to release the SSD door from the base cover. 2. Remove the SSD door from the base cover. Installing SSD door Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the SSD door and provides a visual representation of the installation procedure.
Steps 1. Place the SSD door into its slot on the base cover. 2. Push the SSD door towards right side to lock the SSD door. Next steps 1. Install the SD card. 2. Follow the procedure in after working inside your computer. セカンダリー M.2 ソリッドステート ドライブ Removing the secondary M.2 Solid-state drive Prerequisites NOTE: For computers shipped with M.2 2280 or 2230 SSD installed in slot 6. 1. Follow the procedure in before working inside your computer. 2. Remove the SD card. 3. Remove the SSD door.
Steps 1. 2. 3. 4. 5. 6. Slide the SSD release latch to unlock the SSD module. Remove the (M2x3) screw that secures the SSD module into its slot on the computer. Remove the SSD module from the computer. Remove the (M2x3) screw that secures the SSD thermal pad to the SSD carrier. Remove the SSD thermal pad from the SSD module. For M.2 2280 SSD: a. Remove the M.2 2280 SSD from the SSD carrier. 7. For M.2 2230 SSD: a. Remove the M.2 2230 SSD with its holder from the SSD carrier. b.
Steps 1. For M.2 2280 SSD: a. Place the M.2 SSD onto its slot on SSD carrier. 2. For M.2 2230 SSD: 3. 4. 5. 6. a. Place the M.2 SSD into the SSD holder. b. Replace the (M2x2) screw to secure the M.2 SSD to the holder. c. Place the M.2 SSD with its holder on the SSD carrier. Place the thermal plate above the M.2 SSD module. Replace the (M2x3) screw to secure the SSD thermal plate to the M.2 SSD. Replace the SSD module in its slot on the computer. Replace the (M2x3) screw to secure the SSD module in place.
分解および再アセンブリ
Steps 1. Loosen the eight captive screws that secure the base cover to the computer. 2. Using a plastic scribe, pry open the base cover starting from bottom edge of the cover. NOTE: For models shipped without SmartCard reader, pry open the base cover from the smart card reader slot. Use your fingers to pry open the base cover as the use of plastic scribe or any other sharp objects may damage the base cover.
3. Lift the base cover starting from the bottom edge and remove it from the computer. 4. Disconnect the battery cable from the connector on the system board. Installing the base cover Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the base cover and provides a visual representation of the installation procedure.
分解および再アセンブリ 25
Steps 1. Connect the battery cable to the connector on the system board. 2. Slide the base cover into its slot until it clicks into place. 3. Tighten the eight captive screws to secure the base cover to the computer. Next steps 1. Install the SD card. 2. Follow the procedure in after working inside your computer.
Steps 1. Remove the three (M2x5) screws that secure the battery to the computer. 2. Slightly lift the battery and disconnect the battery cable from the connector on the battery. 3. Remove the battery away from the computer. Installing the battery Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the battery and provides a visual representation of the installation procedure.
Steps 1. Connect the battery cable to the connector in the battery. 2. Place the battery onto its slot in the computer. 3. Replace the three (M2x5) screws to secure the battery to the computer. Next steps 1. Install the base cover. 2. Install the SD card. 3. Follow the procedure in after working inside your computer. ソリッドステートドライブ Removing the primary M.2 Solid-state drive Prerequisites NOTE: For computers shipped with M.2 2280 or 2230 SSD installed in slot 3, slot 4, and/or slot 5. 1.
Steps 1. Remove the (M2x3) screw that secures the SSD thermal plate to the M.2 SSD module. 2. Remove the SSD thermal plate. 3. For M.2 2280 SSD: a. Remove the (M2x3) screw that secures the M.2 SSD to the computer. b. Remove the M.2 SSD. 4. For M.2 2230 SSD: a. Remove the (M2x3) screw that secures the SSD module. b. Remove the SSD module from the computer. c. Remove the (M2x2) screw that secures the SSD to SSD holder. d. Remove the SSD from the holder. 5.
Installing the primary M.2 SSD module Prerequisites NOTE: For computers shipped with M.2 2280 or 2230 SSD installed in slot 3, slot 4, and/or slot 5. If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the primary M.2 SSD and provides a visual representation of the installation procedure. Steps 1. For M.2 2280 SSD: a. Place the M.2 SSD onto its slot on the computer. b.
2. For M.2 2230 SSD: a. Place the M.2 SSD into the SSD holder. b. Replace the (M2x2) screw to secure the M.2 SSD to the holder. c. Place the M.2 SSD module onto its slot on the computer. d. Replace the (M2x3) screw to secure the M.2 SSD module to the computer. 3. Place the thermal plate above the M.2 SSD module. 4. Replace the (M2x3) screw to secure the SSD thermal plate to the M.2 SSD. 5. Repeat the above steps to install the other SSD modules in the computer. Next steps 1. Install the base cover. 2.
Installing the secondary memory module Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the secondary and provides a visual representation of the installation procedure. Steps 1. Align the notch on the memory module with the tab on the memory-module slot. 2. Slide the memory module firmly into the slot and press the memory module until it clicks into place.
Steps 1. Gently slide the SIM card cover towards the left side of the system to unlock the SIM card cover. CAUTION: The SIM card cover is very fragile and can be easily damaged if it is not properly unlocked before opening. 2. Filp the right edge of the SIM card cover to open it. 3. Remove the SIM card from the SIM card slot. Installing the SIM card Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
Steps 1. Slide the SIM card into the SIM card slot. 2. Snap the SIM card cover down. 3. Slide the SIM card cover towards the right of the system to lock the cover. Next steps 1. Install the base cover. 2. Install the SD card. 3. Follow the procedure in after working inside your computer. WLAN カード Removing the WLAN card Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the SD card. 3. Remove the base cover.
Steps 1. 2. 3. 4. Loosen the captive screw that secures the WLAN card bracket to the system board. Remove the WLAN card bracket away from the WLAN card. Disconnect the antenna cables from the WLAN card. Slide at an angle and remove the WLAN card from the connector on the system board. Installing the WLAN card Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
2. Install the SD card. 3. Follow the procedure in after working inside your computer. WWAN カード Removing the WWAN card Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the SD card. 3. Remove the base cover. About this task The figure indicates the location of the WWAN card and provides a visual representation of the removal procedure. Steps 1. 2. 3. 4. Loosen the (M2x3) screw that secures the WWAN card bracket to the system board.
2. Connect the antenna cables to the connectors on the WWAN card. 3. Place the WWAN card bracket above the WWAN card to secure the antenna cables. 4. Tighten the (M2x3) screw to secure the WWAN card bracket to the system board. Next steps 1. Install the base cover. 2. Install the SD card. 3. Follow the procedure in after working inside your computer. キーボード ラティス Removing the keyboard lattice Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the SD card. 3.
Installing the keyboard lattice Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the M.2 SSD and provides a visual representation of the installation procedure. Steps 1. Align the keyboard lattice to its position on the keyboard. 2. Press the edges on the keyboard lattice until it clicks into place. Next steps 1. Install the base cover. 2. Install the SD card. 3.
About this task The figure indicates the location of the keyboard and provides a visual representation of the removal procedure. Steps 1. 2. 3. 4. 5. 6. Lift the latch and disconnect the keyboard cable and the keyboard backlight cable from the connectors on the touchpad module. Turn-over and open the system at 90° angle. Remove the six (M2x2.5) screws that secure the keyboard to the palmrest. Pry the bottom edge of the keyboard and then work along the left and the right sides of the keyboard.
Steps 1. 2. 3. 4. 5. Align the keyboard to its slot on the palmrest Route the keyboard cable and the keyboard backlight cable through the bottom of the palmrest. Replace the six (M2x2.5) screws to secure the keyboard to the palmrest. Turn-over the system at 90° angle to access the keyboard and the keyboard backlight cables. Connect the keyboard backlight cable and the keyboard cable to the connectors on the system board. NOTE: Ensure that you fold the keyboard data cable in perfect alignment.
プライマリ メモリ モジュール Removing the primary memory module Prerequisites 1. 2. 3. 4. 5. 6. Follow the procedure in before working inside your computer. Remove the SD card. Remove the base cover. Remove the battery. Remove the keyboard lattice. Remove the keyboard. About this task The figure indicates the location of the primary memory module and provides a visual representation of the removal procedure. Steps 1. Remove the (M2x3) screw that secures the memory shield in place.
2. Slide the memory shield towards the right side of the computer and lift the shield from the memory module. 3. Pry the securing clips from both side of the memory module until the memory module pops up. 4. Remove the memory module from the memory-module slot. NOTE: Repeat the above steps if there are other memory installed. Installing the primary memory module Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
4. Place the memory shield and slide it towards the left side of the computer to cover the memory module. 5. Replace the (M2x3) screw to secure the memory shield to the memory module. Next steps 1. 2. 3. 4. 5. 6. Install the keyboard. Install the keyboard lattice. Install the battery. Install the base cover. Install the SD card. Follow the procedure in after working inside your computer. ヒートシンク Removing the heat-sink assembly Prerequisites 1. 2. 3. 4.
4. Lift the heat-sink assembly to remove it from the computer. Installing the heat sink assembly Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the keyboard and provides a visual representation of the installation procedure. Steps 1. Align and insert the heat-sink assembly into its slot on the computer. 2.
電源アダプター ポート Removing the power-adapter port Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer. Remove the SD card. Remove the base cover. Remove the battery. Remove the heat-sink assembly. About this task The figure indicates the location of the power-adapter port and provides a visual representation of the removal procedure. Steps 1. 2. 3. 4. Remove the (M2x3) screw that secures power-adapter cable bracket. Remove the power-adapter cable bracket from the computer.
Steps 1. 2. 3. 4. 5. Align and place the power-adapter cable on the computer. Place the power-adapter port into its slot on the plamrest. Replace the power-adapter cable bracket on the power-adapter port. Replace the (M2x3) screw to secure the power-adapter cable bracket to the computer. Connect the power-adapter cable to the connector on the system board. Next steps 1. 2. 3. 4. 5. Install the heat-sink assembly. Install the battery. Install the base cover. Install the SD card.
3. Remove the two (M2x3) screws that secure the power button board to the computer. 4. Remove the power button board with the power button board cable from the computer. 5. Disconnect the power button board cable from the power button board. Installing the power button board Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
Steps 1. Remove the (M2.5x2.5) screw that secures the power button assembly with fingerprint reader cable bracket to the power button board. 2. Remove the power button assembly with fingerprint reader cable bracket from the power button board. 3. Disconnect the power button assembly with fingerprint reader cable from the power button board. 4. Disconnect the power button board cable from the connector on the system board. 5. Peel the power button board cable from the palmrest. 6.
Steps 1. 2. 3. 4. 5. 6. 7. 8. Connect the power button board cable to the power button board. Align and place the power button board with power button cable into its slot on the computer. Replace the two (M2x3) screws to secure the power button board. Adhere the power button board cable to the palmrest. Connect the power button board cable to the connector on the system board.
Steps 1. 2. 3. 4. Unroute the WLAN and WWAN antenna cables from the routing guide. Disconnect the keyboard cable and the keyboard backlight cable from the connector on the touchpad module. Remove the six (M2x5) and the nine (M2x3) screws that secure the inner frame to the computer chassis. Remove the inner frame from the computer while carefully unthreading the keyboard cable and keyboard backlight cable through the opening on the inner frame.
Steps 1. Carefully route the keyboard and keyboard backlight cable through the inner frame and place the inner frame on the computer chassis. 2. Replace the six (M2x5) and the nine (M2x3) screws to secure the inner frame in place. 3. Route the WLAN and WWAN antenna cables through the routing guide. Next steps 1. 2. 3. 4. 5. 6. 7. Install the WLAN card. Install the WWAN card. Install the primary M.2 SSD. Install the battery. Install the base cover. Install the SD card.
About this task The figure indicates the location of the smart-card reader and provides a visual representation of the removal procedure. Steps 1. 2. 3. 4. 5. Disconnect the touchpad buttons cable from the touchpad. Disconnect the smart-card reader cable from the connector on the USH daughter board. Peel the smart-card reader cable from the touchpad. Remove the two (M2x2.5) screws that secure the smart-card reader to the computer. Remove the smart-card reader from the computer.
Steps 1. 2. 3. 4. 5. Align and place the smart-card reader into its slot on the computer. Replace the two (M2x2.5) screws to secure the smart-card reader in place. Adhere the smart-card reader cable to the touchpad. Connect the smart-card reader cable to the connector on the USH daughter board. Connect the touchpad button cable to the connector on the touchpad. Next steps 1. 2. 3. 4. 5. 6. 7. 8. Install the WLAN card. Install the WWAN card. Install the primary M.2 SSD. Install the inner frame.
About this task The figure indicates the location of the touchpad buttons and provides a visual representation of the removal procedure. Steps 1. For models shipped with smart card reader, disconnect the smart card reader cable from the USH daughter board and peel the smart card reader cable from the touchpad. 2. Disconnect the touchpad buttons cable from the connector on the touchpad. 3. Remove the two (M2x2.5) screws that secure the touchpad buttons to the palmrest. 4.
Steps 1. 2. 3. 4. Place the touchpad buttons into its slot in the palmrest. Replace the two (M2x2.5) screws to secure the touchpad buttons to the palmrest Connect the touchpad buttons cable to the connector in the touchpad. For models shipped with smart card reader, connect the smart card reader cable to the USH daughter board and adhere the smart card reader cable on the touchpad. Next steps 1. 2. 3. 4. 5. 6. 7. 8. Install the inner frame. Install the WLAN card. Install the WWAN card.
About this task The figure indicates the location of the SD card reader and provides a visual representation of the removal procedure. Steps 1. 2. 3. 4. Disconnect the SD card reader cable from the connector on the system board. Disconnect the LED board cable from the SD card reader on the bottom side of the computer. Remove the (M2.5x2.5) screw that secures the SD card reader in place. Slide and remove the SD card reader with its cable out of the computer.
Steps 1. 2. 3. 4. Align and place the SD care reader with its slot on the palmrest. Replace the (M2.5x2.5) screw to secure the SD card reader to the palmrest. Connect the LED board cable to the SD card reader on the bottom side of the computer. Connect the SD card reader cable to the connector on the system board. Next steps 1. 2. 3. 4. 5. 6. 7. 8. 9. Install the inner frame. Install the WLAN card. Install the WWAN card. Install the primary M.2 SSD. Install the inner frame. Install the battery.
Steps 1. Remove the two (M2x3) screws that secure the power button in its slot on the computer. 2. Remove the power button from the computer. Installing the power button Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the power button and provides a visual representation of the installation procedure.
Steps 1. Place the power button into its slot on the computer. 2. Replace the two (M2x3) screws to secure the power button in place. Next steps 1. 2. 3. 4. 5. 6. Install the power button board. Install the heat-sink assembly. Install the battery. Install the base cover. Install the SD card. Follow the procedure in after working inside your computer. 指紋認証リーダー内蔵電源ボタン アセンブリー Removing the power button assembly with fingerprint reader Prerequisites 1. 2. 3. 4. 5. 6.
Installing the power button assembly with fingerprint reader Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the power button and provides a visual representation of the installation procedure. Steps 1. Place the power button assembly with fingerprint reader into its slot on the computer. 2.
5. Remove the keyboard lattice. 6. Remove the keyboard. About this task The figure indicates the location of the GPU power cable and provides a visual representation of the removal procedure. Steps 1. Carefully pry the GPU power cable connector outside the end of the connector head to unlock the GPU power cable connector from the GPU card. 2. Slightly slide the GPU power cable connector outwards to disconnect the GPU power cable from the GPU card. 3.
Steps 1. 2. 3. 4. Adhere the GPU power cable into its slot on the computer. Disconnect the GPU power cable from the connector on the system board. Slide the GPU power cable connector into its slot to connect the GPU power cable to the GPU card. Lock the GPU power cable connector to secure the GPU card. Next steps 1. 2. 3. 4. 5. 6. Install the keyboard. Install the keyboard lattice. Install the battery. Install the base cover. Install the SD card.
12. 13. 14. 15. 16. Remove the keyboard lattice. Remove the keyboard. Remove the primary memory. Remove the heat-sink assembly. Remove the inner frame. About this task The figure indicates the location of the system board and provides a visual representation of the removal procedure. Images to be uploaded in the next review cycle.
Steps 1. Carefully pry the GPU power cable connector outside the end of the connector head to unlock the GPU power cable connector from the system board on top side of the system. 2. Slightly slide the GPU power cable connector outwards to disconnect the GPU power cable from the connector on the system board. 3. Disconnect the speaker cable and the SD card reader cable from the connectors on the system board. 4.
NOTE: For UMA models, remove the two (M2x3) screws that secure the single beam connector in place on the bottom of the system. 10. 11. 12. 13. 14. 15. 16. Remove the beam connectors from the computer. Remove the (M2x5) screw that secures the display cable bracket in place. Remove the display cable bracket from the computer. Disconnect the display cable from the connector on the system board. Remove the four (M2x5) screws that secure the system board to the computer.
分解および再アセンブリ
Steps 1. Adhere the coin-cell battery to the palmrest and then place the system board on its slot on the palmrest. 2. Replace the four (M2x5) screws to secure the system board to the palmrest. 3.
4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Install the keyboard. Install the keyboard lattice. Install the WLAN card. Install the WWAN card. Install the secondary memory. Install the SIM card. Install the primary M.2 SSD. Install the inner frame. Install the battery. Install the base cover. Install the secondary M.2 SSD. Install the SSD door. Install the SD card. Follow the procedure in after working inside your computer. GPU カード GPU カードの取り外し 前提条件 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
GPU カードの取り付け 前提条件 コンポーネントを交換する場合、取り付け手順を実行する前に、既存のコンポーネントを取り外してください。 このタスクについて 図は GPU カードの位置を示すもので、取り付け手順を視覚的に表しています。 次のレビュー サイクルでアップロードされる画像です。 手順 1. GPU カードをパームレストのスロットに合わせてセットします。 2. 3 本のネジ(M2x5)を取り付けて GPU カードをパームレストに固定します。 次の手順 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. システム ボードを取り付けます。 内部フレームを取り付けます。 ヒートシンク アセンブリーを取り付けます。 プライマリー メモリーを取り付けます。 GPU 電源ケーブルを取り付けます。 キーボードを取り付けます。 キーボード ラティスを取り付けます。 WLAN カードを取り付けます。 WWAN カードを取り付けます。 セカンダリー メモリーを取り付けます。 SIM カードを取り付けます。 プライマリー M.
14. 15. 16. 17. 18. 19. Remove the primary memory. Remove the heat-sink assembly. Remove the inner frame. Remove the GPU power cable. Remove the GPU card. Remove the system board. About this task The figure indicates the location of the speaker and provides a visual representation of the removal procedure. Images to be uploaded in the next review cycle. Steps 1. Peel the pieces of adhesive tape that secures the speaker cable to the palmrest. 2.
Steps 1. Align and place the speaker module into its slot on the top edge of the palmrest. 2. Adhere the three piece adhesive tape to secure the speaker cable in place on the palmrest. Next steps 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Install the system board. Install the GPU card. Install the GPU power cable. Install the inner frame. Install the heat-sink assembly. Install the primary memory. Install the keyboard. Install the keyboard lattice. Install the WLAN card.
ミドル キャップ Removing the middle cap Prerequisites 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Follow the procedure in before working inside your computer. Remove the SD card. Remove the SSD door. Remove the secondary M.2 SSD. Remove the base cover. Remove the battery. Remove the primary M.2 SSD. Remove the SIM card. Remove the secondary memory. Remove the WWAN card. Remove the WLAN card. Remove the keyboard lattice. Remove the keyboard. Remove the primary memory.
2. Remove the middle cap from the computer. Installing the middle cap Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the middle cap and provides a visual representation of the installation procedure. Steps 1. Align and insert the middle cap onto the palmrest. NOTE: Ensure that the middle cap is secured in place by the two pegs on the palmrest. 2.
15. 16. 17. 18. 19. Install the base cover. Install the secondary M.2 SSD. Install the SSD door. Install the SD card. Follow the procedure in after working inside your computer. ディスプレイアセンブリ Removing the display assembly Prerequisites 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Follow the procedure in before working inside your computer. Remove the SD card. Remove the SSD door. Remove the secondary M.2 SSD. Remove the base cover. Remove the battery. Remove the primary M.2 SSD. Remove the SIM card.
分解および再アセンブリ 75
Steps 1. Open the display assembly to a 140-degree angle and place the computer at the edge of a flat table so that the display assembly can extend below the table. 2. Remove the (M2x5) screw that secures the display bracket to the palmrest. 3. Disconnect the display cable from the connector on the system board. 4. Remove the (M2x5) screw that secures the Darwin bracket. 5. Peel and remove the WWAN cables and Darwin cables from the palmrest. 6. Remove the eight (M2.5x2.
分解および再アセンブリ 77
Steps 1. 2. 3. 4. 5. 6. NOTE: Before installing the display assembly, ensure that the display hinges are opened to a 140-degree angle against the display assembly, to fit the display assembly to the palmrest. Align the screw holes on the hinges on the display assembly to the screw holes on the palmrest. Replace the eight (M2.5x2.5) screws to secure the hinges to the palmrest. Replace the (M2x5) screw to secure the display bracket to the palmrest.
13. Install the SSD door. 14. Install the SD card. 15. Follow the procedure in after working inside your computer. パームレスト Removing the palmrest Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the SD card. 3. Remove the SSD door. 4. Remove the secondary M.2 SSD. 5. Remove the base cover. 6. Remove the battery. 7. Remove the primary M.2 SSD. 8. Remove the SIM card. 9. Remove the secondary memory. 10. Remove the WWAN card. 11. Remove the WLAN card. 12.
Installing the palmrest Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the palmrest and before performing the pre-installation parts procedures for any palmrest installation procedure. Next steps 1. Install the display assembly.
2. Install the middle cap. 3. Install the speaker. 4. Install the system board. 5. Install the GPU card. 6. Install the GPU power cable. 7. Install the inner frame. 8. Install the heat-sink assembly. 9. Install the power button or power button assembly with fingerprint reader. 10. Install the SD card reader. 11. Install the smart card reader. 12. Install the touchpad buttons. 13. Install the power button board. 14. Install the power adapter port. 15. Install the primary memory. 16. Install the keyboard. 17.
22. Remove the display assembly. About this task The figure indicates the location of the display bezel and provides a visual representation of the removal procedure. Images to be uploaded in the next review cycle. Steps 1. Using a flat head tool or a plastic scribe, pry open the display bezel from the two recess points on the bottom edge of the display bezel. 2. Working your way from the bottom edge, pry around the sides and top edge of the display bezel.
Steps 1. Place the display bezel on the display assembly. 2. Press the edges of the display bezel until it clicks onto the display assembly. Next steps 1. Install the display assembly. 2. Install the middle cap. 3. Install the speaker. 4. Install the system board. 5. Install the GPU card. 6. Install the GPU power cable. 7. Install the inner frame. 8. Install the heat-sink assembly. 9. Install the primary memory. 10. Install the keyboard. 11. Install the keyboard lattice. 12. Install the WLAN card. 13.
21. Install the SD card. 22. Follow the procedure in after working inside your computer. ディスプレイパネル Removing the display panel (non-touch) Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the SD card. 3. Remove the SSD door. 4. Remove the secondary M.2 SSD. 5. Remove the base cover. 6. Remove the battery. 7. Remove the primary M.2 SSD. 8. Remove the SIM card. 9. Remove the secondary memory. 10. Remove the WWAN card. 11. Remove the WLAN card. 12.
Steps 1. 2. 3. 4. 5. 6. 7. 8. Remove the two (M2.5x2.5) screws and the two (M2x2.5) screws that secures the display panel to the display assembly. Lift the display panel and turn the display panel over to access the display cable Peel the conductive tape covering the display cable. Peel the adhesive tapes that secures the display cable. Peel the adhesive rubber strip covering the display cable. Unlock the display cable connector and then disconnect the display cable from the back of the display panel.
Installing the display panel (non-touch) Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the display panel and provides a visual representation of the installation procedure. Steps 1. 2. 3. 4. 86 Connect the display cable to the connector on the back of the display panel and lock the display cable connector. Adhere the adhesive rubber strip to cover the display cable.
5. Replace the two (M2.5X2.5) and two (M2x2.5) screws to secure the display panel to the display assembly. Next steps 1. Install the display bezel. 2. Install the display assembly. 3. Install the middle cap. 4. Install the speaker. 5. Install the display assembly. 6. Install the system board. 7. Install the GPU card. 8. Install the GPU power cable. 9. Install the inner frame. 10. Install the heat-sink assembly. 11. Install the primary memory. 12. Install the keyboard. 13. Install the keyboard lattice. 14.
22. Remove the display bezel. 23. Remove the display panel. About this task The figure indicates the location of the display hinge and provides a visual representation of the removal procedure. Images to be uploaded in the next review cycle. Steps 1. Remove the eight (M2.5x2.5) screws that secures the display hinges to the display assembly. 2. Remove the display hinges.
Steps 1. Place the display hinge in its slot on the display assembly. 2. Replace the eight (M2.5x2.5) screws to secure the display hinge to the display assembly. Next steps 1. Install the display panel. 2. Install the display bezel. 3. Install the speaker. 4. Install the display assembly. 5. Install the system board. 6. Install the GPU card. 7. Install the GPU power cable. 8. Install the inner frame. 9. Install the heat-sink assembly. 10. Install the primary memory. 11. Install the keyboard. 12.
カメラ Removing the camera (non-touch) Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the SD card. 3. Remove the SSD door. 4. Remove the secondary M.2 SSD. 5. Remove the base cover. 6. Remove the battery. 7. Remove the primary M.2 SSD. 8. Remove the SIM card. 9. Remove the secondary memory. 10. Remove the WWAN card. 11. Remove the WLAN card. 12. Remove the keyboard lattice. 13. Remove the keyboard. 14. Remove the primary memory. 15. Remove the heat-sink assembly. 16.
Steps 1. 2. 3. 4. Peel the adhesive tape that covers the camera module. Disconnect the display cable from the camera module. Gently pry the camera shutter cap from the top edge of the camera shutter and remove it from the display back cover. Gently pry the camera module from the display back cover. Installing the camera Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
13. Install the WLAN card. 14. Install the WWAN card. 15. Install the secondary memory. 16. Install the SIM card. 17. Install the primary M.2 SSD. 18. Install the battery. 19. Install the base cover. 20. Install the secondary M.2 SSD. 21. Install the SSD door. 22. Install the SD card. 23. Follow the procedure in after working inside your computer. P センサー ボード P センサー ボードの取り外し 前提条件 1. PC 内部の作業を始める前にの手順に従います。 2. SD カードを取り外します。 3. SSD ドアを取り外します。 4. セカンダリー M.2 SSD を取り外します。 5. ベース カバーを取り外します。 6. バッテリーを取り外します。 7.
P センサー ボードの取り付け 前提条件 コンポーネントを交換する場合、取り付け手順を実行する前に、既存のコンポーネントを取り外してください。 このタスクについて 図は P センサー ボードを示すもので、取り付け手順を視覚的に表しています。 次のレビュー サイクルでアップロードされる画像です。 手順 1. モニター ケーブルを P センサー ボードに接続します。 2. P センサー ボードを裏返して、ディスプレイ背面カバーのスロットに慎重にセットします。 次の手順 1. モニター パネルを取り付けます。 2. ディスプレイ ベゼルを取り付けます。 3. スピーカーを取り付けます。 4. ディスプレイ アセンブリーを取り付けます。 5. システム ボードを取り付けます。 6. GPU カードを取り付けます。 7. GPU 電源ケーブルを取り付けます。 8. 内部フレームを取り付けます。 9. ヒートシンク アセンブリーを取り付けます。 10. プライマリー メモリーを取り付けます。 11. キーボードを取り付けます。 12. キーボード ラティスを取り付けます。 13. WLAN カードを取り付けます。 14.
9. Remove the secondary memory. 10. Remove the WWAN card. 11. Remove the WLAN card. 12. Remove the keyboard lattice. 13. Remove the keyboard. 14. Remove the primary memory. 15. Remove the heat-sink assembly. 16. Remove the inner frame. 17. Remove the GPU power cable. 18. Remove the GPU card. 19. Remove the system board. 20. Remove the display assembly. 21. Remove the speaker. 22. Remove the display bezel. 23. Remove the display panel. 24. Remove the P-sensor board.
4. Remove the display cable from the display back cover. Installing the display cable Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the display cable and provides a visual representation of the installation procedure. Steps 1. Route and adhere the display cable on the display back cover. 2. Connect the display cable to the connector on the camera module. 3.
8. Install the GPU power cable. 9. Install the inner frame. 10. Install the heat-sink assembly. 11. Install the primary memory. 12. Install the keyboard. 13. Install the keyboard lattice. 14. Install the WLAN card. 15. Install the WWAN card. 16. Install the secondary memory. 17. Install the SIM card. 18. Install the primary M.2 SSD. 19. Install the battery. 20. Install the base cover. 21. Install the secondary M.2 SSD. 22. Install the SSD door. 23. Install the SD card. 24.
For installing the components, place the display back cover on a flat surface. 1. Install the display cable. 2. Install the camera. 3. Install the display hinges. 4. Install the P-sensor board. 5. Install the display panel. 6. Install the display bezel. 7. Install the speaker. 8. Install the display assembly. 9. Install the system board. 10. Install the GPU card. 11. Install the GPU power cable. 12. Install the inner frame. 13. Install the heat-sink assembly. 14. Install the primary memory. 15.
4 トラブルシューティング Dell SupportAssist 起動前システム パフォーマンス チェック診断 このタスクについて SupportAssist 診断(システム診断とも呼ばれる)ではハードウェアの完全なチェックを実行します。Dell SupportAssist 起動前シス テム パフォーマンス チェック診断は BIOS に組み込まれており、BIOS によって内部で起動します。組み込み型システム診断プロ グラムには、特定のデバイスまたはデバイス グループ用の一連のオプションが用意されており、以下の処理が可能です。 • • • • • • テストを自動的に、または対話モードで実行 テストの繰り返し テスト結果の表示または保存 詳細なテストで追加のテストオプションを実行し、障害の発生したデバイスに関する詳しい情報を得る テストが問題なく終了したかどうかを知らせるステータスメッセージを表示 テスト中に発生した問題を通知するエラーメッセージを表示 メモ: 特定のデバイスについては、ユーザーによる操作が必要なテストもあります。診断テストを実行する際は、コンピュー ター端末の前に必ずいるようにしてください。
システム ボード ビルトイン自己テスト(M-BIST) このタスクについて 手順 1. M キーと電源ボタンの両方を長押しして、M-BIST を起動します。 2. バッテリーステータス ライトは、システム ボードに障害が発生した場合オレンジ色に点灯します。 3.
モニター パネルのビルトイン自己テスト(LCDBIST) このタスクについて 手順 1. 「D」キーを押したまま、「電源」ボタンを押します。 2. PC の POST が開始されたら、「D」キーと「電源」ボタンの両方を解放します。 3. モニター パネルに単色が表示されたり、異なる色が順に表示されます。 メモ: 色の順序は、モニター パネルのベンダーによって異なることがありますが、これはユーザーが色のゆがみやグラフィ ックの異常がなく、正しく表示されていることを確認するためのものです。 4.
表 6. LED コード 診断ライト コード 問題の内容 推奨される解決策 1.
Wi-Fi 電源の入れ直し このタスクについて お使いのコンピューターが Wi-Fi 接続の問題が原因でインターネットにアクセスできない場合は、Wi-Fi 電源の入れ直し手順を実施 することができます。次に、Wi-Fi 電源の入れ直しの実施方法についての手順を示します。 メモ: 一部の ISP(インターネット サービス プロバイダ)はモデム/ルータ コンボ デバイスを提供しています。 手順 1. 2. 3. 4. 5. 6. 7.
5 ヘルプ トピック: デルへのお問い合わせ • デルへのお問い合わせ 前提条件 メモ: お使いのコンピュータがインターネットに接続されていない場合は、購入時の納品書、出荷伝票、請求書、またはデル の製品カタログで連絡先をご確認ください。 このタスクについて デルでは、オンラインまたは電話によるサポートとサービスのオプションを複数提供しています。サポートやサービスの提供状況 は国や製品ごとに異なり、国 / 地域によってはご利用いただけないサービスもございます。デルのセールス、テクニカルサポー ト、またはカスタマーサービスへは、次の手順でお問い合わせいただけます。 手順 1. 2. 3. 4. Dell.