Dell Precision Arbetsstation R7610 Ägarens handbok Regleringsmodell: E15S Regleringstyp: E15S002
Upplysningar och varningar OBS: Ger viktig information som kan hjälpa dig att få ut mer av datorn. CAUTION: VIKTIGT! Indikerar risk för skada på maskinvaran eller förlust av data, samt ger information om hur du undviker problemet. VARNING: En varning signalerar risk för egendomsskada, personskada eller dödsfall. © 2013 Dell Inc.
Innehåll Upplysningar och varningar.........................................................................................................2 1 Arbeta med datorn......................................................................................................................7 Innan du arbetar inuti datorn....................................................................................................................................7 Rekommenderade verktyg..............................................
18 Installera kylhöljet ..................................................................................................................43 19 Ta bort SAS (Serial attached SCSI)-backplane.................................................................45 20 Installera SAS (Serial attached SCSI)-backplane.............................................................47 21 Ta bort den främre chassimonteringen...............................................................................
40 Installera värdkortet för fjärråtkomst...................................................................................89 41 Ta bort SAS-styrenhetskortet...............................................................................................91 42 Installera SAS-styrenhetskortet...........................................................................................93 43 Ta bort moderkortet..........................................................................................................
Arbeta med datorn 1 Innan du arbetar inuti datorn Följ säkerhetsanvisningarna nedan för att skydda dig och datorn mot potentiella skador. Om inget annat anges förutsätts i varje procedur i det här dokumentet att följande villkor har uppfyllts: • Du har läst säkerhetsinformationen som medföljde datorn. • En komponent kan ersättas eller – om du köper den separat – monteras i omvänd ordning jämfört med borttagningsproceduren.
Rekommenderade verktyg Procedurerna i detta dokument kan kräva att följande verktyg används: • Liten spårskruvmejsel • Stjärnskruvmejsel • Liten plastrits Stänga av datorn CAUTION: Undvik dataförlust genom att spara och stänga alla öppna filer och avsluta alla program innan du stänger av datorn. 1. Stäng av operativsystemet: – I Windows 8: * Med en pekaktiverad enhet: a. Svep från högerkanten på skärmen, öppna menyn med snabbknappar och välj Inställningar. b.
3. Anslut datorn och alla anslutna enheter till eluttagen. 4. Starta datorn. 5. Kontrollera vid behov att datorn fungerar korrekt genom att köra Dell Diagnostics.
Systemöversikt 2 Bilden nedan visar insidan av datorn efter framramen och höljet har avlägsnats. Bildtexten visar namnen och komponenternas layout inuti datorn. 1. kontrollpanel 2. plasthölje 3. kylhölje 4. fläktfäste 5. systemfläktar 6. strömfördelningsenhet 7. mellersta lådan för expansionskort 8. yttre lådan för expansionskort 9. knappcellsbatteri 10. SAS-backplane 11. främre chassimontering 12. hårddisken 13.
Ta bort frontramen 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Lås upp frontramen med den tillhörande nyckeln. 3 a) Lyft upp frigöringsfliken för frontramen och dra bort ramen från datorn.
Installera frontramen 1. För in frontramen nedåt i dess plats och tryck in den mot datorn. 2. Sätt fast frigöringsfliken. 3. Lås fast frontramen med den tillhörande nyckeln. 4. Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort kåpan 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: 3. Rotera frigöringsmekanismen för haken moturs till den olåsta positionen. – 5 frontramen a) Lyft upp haken och skjut kåpan bakåt i datorn. 4. Lyft bort kåpan från datorn.
Installera kåpan 1. Placera kåpan på datorn och tryck den nedåt tills den klickar på plats. 2. Tryck ned haken för kåpan. 3. Installera frontramen. 4. Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort nätaggregatet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Tryck den orange fliken mot haken och håll den intryckt. Dra sedan ut nätaggregatet från datorn.
Installera nätaggregatet 1. Sätt i nätaggregatet i datorn tills det klickar på plats. 2. Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort hårddiskhållaren 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort frontramen. 3. Tryck in frigöringsknappen för hårddiskhållaren. 9 a) Dra i handtaget för hårddiskhållaren tills det öppnas. b) Skjut ut hårddisken ur enhetsfacket.
Installera hårddiskhållaren 1. Sätt i hårddisken i enhetsuttaget. 2. Tryck på handtaget för hårddiskhållaren tills den klickar på plats. 3. Installera frontramen. 4. Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort hårddiskmonteringen 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: 3. – frontramen – hårddiskhållare 11 Ta bort skruvarna som håller fast hårddiskhållaren mot hårddisken. a) Skjut ut hårddisken ur enhetsfacket.
Installera hårddiskmonteringen 1. Placera hårddisken i hårddiskkassetten. 2. Dra åt skruvarna som håller fast hårddisken på båda sidorna av hårddiskkassetten. 3. Installera: 4. – hårddiskhållare – frontramen 12 Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort kontrollpanelen 13 CAUTION: Det krävs två typer av Torx-skruvmejslar för att demontera/montera kontrollpanelen, en T10 och en T8. 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: 3. – frontramen – kåpan Ta bort Torx-skruven som håller fast kontrollpanelen. a) Ta bort kablarna för kontrollpanelen. b) Ta bort skruvarna som håller fast kontrollpanelskortet.
Installera kontrollpanelen 1. Anslut kablarna för kontrollpanelen. 2. Installera skruvarna som håller fast kontrollpanelen. 3. Sätt tillbaka torx-skruvarna som håller fast kontrollpanelen. 4. Installera: 5. – kåpan – frontramen 14 Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort den optiska enheten 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: 3. – frontramen – kåpan – kylhölje 15 Tryck in den blå frigöringsfliken i den indikerade riktningen och lyft plastkåpan. a) Frigör plastkåpan från gångjärnen som håller fast den på den andra sidan och avlägsna den från datorn. 4. Ta bort ström- och datakablarna till den optiska enheten. a) Håll den blå frigöringsfliken nedtryckt och skjut den framåt i datorn.
Installera den optiska enheten 16 1. Sätt i den optiska enheten i enhetsuttaget. 2. Anslut ström- och datakablarna. 3. Sätt tillbaka plastkåpan genom att fästa flikarna på ena sidan på metallgångjärnen och genom att trycka ner den andra sidan tills den klickar fast på plats. 4. Installera: 5. – kylhölje – kåpan – frontramen Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort kylhöljet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: 3. – frontramen – kåpan 17 Lyft försiktigt kylhöljet rakt uppåt och bort från moderkortet.
Installera kylhöljet 1. Placera kylhöljet framför systemfläktarna i moderkortet. 2. Installera: 3. – kåpan – frontramen 18 Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort SAS (Serial attached SCSI)-backplane 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: – frontramen – kåpan – kylhölje – optisk enhet – hårddiskhållare – hårddiskmontering 3. Ta bort alla SAS-kablarna genom att trycka in deras respektive frigöringsflikar. 4. Tryck in de blå frigöringsflikarna i pilarnas riktning mot hårddiskenheten för att frigöra SAS-backplane från moderkortet. 19 a) Lyft ut SAS-backplane ur datorn.
20 Installera SAS (Serial attached SCSI)-backplane 1. Tryck in de blå frigöringsflikarna och för in backplane i platsen på moderkortet längs hårddiskmonteringen. 2. Anslut SAS-kablarna. 3. Installera: 4. – hårddiskmontering – hårddiskhållare – optisk enhet – kylhölje – kåpan – frontramen Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort den främre chassimonteringen 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: 3. – frontramen – kåpan – kylhölje 21 Tryck inåt på de två frigöringsflikarna och skjut den främre chassimonteringen mot datorns framsida.
Installera den främre chassimonteringen 1. Skjut den främre chassimonteringen bakåt i datorn tills den klickar på plats. 2. Installera: 3. – kylhölje – kåpan – frontramen 22 Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort fläktfästet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: 3. – kåpan – kylhölje 23 Dra båda frigöringsflikarna uppåt samtidigt för att lossa fläktfästet. a) Lyft fläktfästet och ta bort det från datorn.
Installera fläktfästet 1. Placera fläktfästet i datorn. 2. Se till att det inte finns några kablar ovanpå fläktkontakterna. 3. Tryck de två frigöringsflikarna samtidigt nedåt för att säkra fästet. 4. Installera: 5. – kylhölje – kåpan 24 Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort systemfläktarna 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: 3. – kåpan – främre chassimontering 25 Tryck på frigöringsfliken och lyft ut fläkten från systemfläktmonteringen. a) Upprepa momentet ovan för att ta bort de kvarstående systemfläktarna från monteringen.
Installera systemfläktarna 1. Sätt i fläkten i systemfläktmonteringen tills den klickar på plats. 2. Upprepa momentet ovan för att installera de kvarstående systemfläktarna i monteringen. 3. Installera: 4. – främre chassimontering – kåpan 26 Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort knappcellsbatteriet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: 3. – frontramen – kåpan – kylhölje – fläktfäste 27 Tryck bort frigöringshaken från batteriet så att det hoppar upp från sockeln. Lyft ut knappcellsbatteriet ur datorn.
Installera knappcellsbatteriet 1. Placera knappcellsbatteriet i facket på moderkortet. 2. Tryck ned knappcellsbatteriet tills frigöringshaken fjädrar tillbaka och håller fast batteriet. 3. Installera: 4. – fläktfäste – kylhölje – kåpan – frontramen 28 Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort minnet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: 3. – frontramen – kåpan – kylhölje – främre chassimontering – fläktfäste 29 Tryck nedåt på minnets låsklämmor på vardera sida av minnesmodulerna och lyft minnesmodulen uppåt för att ta bort den från datorn.
Installera minnet 1. Sätt in minnesmodulen i minnessockeln. 2. Tryck nedåt på minnesmodulen tills låsklämmorna fäster minnet på plats. 3. Installera: 4. – fläktfäste – främre chassimontering – kylhölje – kåpan – frontramen 30 Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort kylflänsen 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: – frontramen – kåpan – kylhölje – fläktfäste 31 3. Skjut den främre chassienheten framåt. 4. Lossa fästskruvarna på kylflänsen. De diagonalt motsatta skruvarna bör börja lossas för att förhindra att ena sidan av kylflänsen sjunker vid borttagningen. a) Lyft bort kylflänsen från datorn.
Installera kylflänsen 1. Placera kylflänsen över processorn på moderkortet. 2. Dra åt och fäst de diagonalt motsatta skruvarna på kylflänsen. 3. Installera: 4. – fläktfäste – främre chassimontering – kylhölje – kåpan – frontramen 32 Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort processorn 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: 3. – frontramen – kåpan – kylhölje – främre chassimontering – fläktfäste – kylflänsen 33 Så här tar du bort processorn. OBS: Processorkåpan sitter fast med två spakar. På spakarna finns bilder som talar om vilken spak som måste öppnas först och vilken spak som måste stängas först. a) b) c) d) Tryck ned den första spaken som håller processorn på plats och frigör den i sidled från hållkroken.
4. Upprepa stegen ovan för att ta bort den andra processorn (om sådan finns) från datorn. Du kan kontrollera om datorn har plats för dubbla processorer genom att läsa i Moderkortskomponenter.
Installera processorn 1. Placera processorn i sockeln. 2. Sätt tillbaka processorkåpan. 34 OBS: Processorkåpan sitter fast med två spakar. På spakarna finns bilder som talar om vilken spak som måste öppnas först och vilken spak som måste stängas först. 3. Skjut spaken i sidled in i hållkroken så att processorn sitter fast. 4. Upprepa steg "3" och skjut in den andra spaken från hållkroken. 5. Installera: 6.
Ta bort lådorna för expansionskorten 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: – frontramen – kåpan 3. Trä ut nätkablarna ur metallklämmorna. 4. Lyft den yttre lådan för expansionskorten och vänd den upp och ned.
5. Ta bort alla kablarna som leder upp till den yttre lådan för expansionskorten, och lyft bort den från datorn. 6. Ta bort alla kablarna som leder upp till den mellersta lådan för expansionskorten.
7. Lyft den mellersta lådan för expansionskorten uppåt och flytta bort den från datorn.
Installera lådorna för expansionskorten 1. Anslut kablarna som leder till den mellersta lådan för expansionskortet. 2. Fäst den mellersta lådan för expansionskorten i datorn. 3. Anslut kablarna som leder till den yttersta lådan för expansionskortet. 4. Fäst den yttersta lådan för expansionskorten i datorn. 5. Dra kablarna som leder till lådan för expansionskortet. 6. Installera: 7. – kåpan – frontramen 36 Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort strömfördelningsenheten 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: – frontramen – kåpan – kylhölje – nätaggregatet – systemfläktar – fläktfäste 37 3. Skjut den främre chassienheten framåt. 4. Dra ur strömkontakten för den optiska enheten samt SAS-backplane-kontakten genom att trycka in skåran på vardera enskild kontakt och dra dem utåt. 5.
6. Ta loss alla kablar från kabelhållarna. 7. Ta bort skruvarna som håller fast strömfördelningsenheten. a) Lyft upp strömfördelningsenheten och ta bort den från datorn.
Installera strömfördelningsenheten 1. Placera strömfördelningsenheten i datorn. 2. Sätt i skruvarna som håller fast strömfördelningsenheten. 3. Dra alla nätsladdarna genom sina kabelkanaler. 4. Anslut strömkontakterna för CPU 1, CPU 2, SAS-backplane och den optiska enheten. 5. Skjut den främre chassimonteringen till dess ursprunliga plats. 6. Installera: 7.
Ta bort värdkortet för fjärråtkomst 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: – frontramen – kåpan – lådor för expansionskort 3. Ta bort alla korten från lådan för förlängningskort. 4. Lyft frigöringsfliken uppåt och skjut förlängningskortet åt höger för att ta bort den från datorn.
Installera värdkortet för fjärråtkomst 1. Installera värdkortet för fjärråtkomst i dess plats. 2. Installera: 3. – lådor för expansionskort – kåpan – frontramen 40 Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort SAS-styrenhetskortet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: 3. – frontramen – kåpan – lådor för expansionskort – värdkort för fjärråtkomst 41 Ta bort skruvarna som håller fast SAS-styrenhetskortet och avlägsna det från datorn.
Installera SAS-styrenhetskortet 1. Installera skruvarna som håller fast SAS-styrenhetskortet. 2. Installera: 3. – värdkort för fjärråtkomst – lådor för expansionskort – kåpan – frontramen 42 Följ anvisningarna i När du har arbetat inuti datorn.
Ta bort moderkortet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: 3. – frontramen – kåpan – kylhölje – kylflänsen – processorn – minne – främre chassimontering – nätaggregatet – fläktfäste – lådor för expansionskort – strömfördelningsenhet 43 Lyft den blå frigöringsfliken, skjut moderkortet framåt i den indikerade riktningen och avlägsna den från datorn.
Installera moderkortet 1. Placera moderkortet i chassit. 2. Skjut moderkortet mot datorns baksida. 3. Tryck in den blå frigöringsfliken. 4. Installera: 5. – strömfördelningsenhet – lådor för expansionskort – fläktfäste – minne – processorn – kylflänsen – främre chassimontering – kylhölje – kåpan – frontramen 44 Följ anvisningarna i När du har arbetat inuti datorn.
Komponenter på moderkortet 45 Efterföljande bilder visar moderkortskomponenterna. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. DIMM-fack Systemfläktkontakter Frontpanelskontakt CPU 2 minnesströmkontakt Kontakt för strömfördelningsenhet 24-stifts strömkontakt Främre USB-kontakt I/O-förlängningsbuss SAS-kontakter PCIe G2 S7 busskontakt I/O-förlängningsbuss 12. 13. 14. 15. 16. 17. 18. 19. 20.
46 Felsökning Diagnostiklysdioder OBS: Diagnostiklysdiodernas funktion är endast att indikera statusen för POST-processen. Lysdioderna indikerar inte problemet som gjorde att POST-rutinen stannade. Diagnostiklysdioderna sitter bredvid strömbrytaren på chassits framsida. De här diagnostiklysdioderna är endast aktiva och synliga under POST-processen. När operativsystemet börjar laddas stängs de av och är inte längre synliga.
Lampmönster Diagnostiklysdioder Problembeskrivning Felsökningssteg Strömbrytarlysdiod • Ett möjligt fel på moderkortet har uppstått. Ett möjligt fel på moderkort, strömförsörjning eller kringutrustning har uppstått. Koppla bort datorn. Vänta i en minut så att strömmen laddas ur datorn. Koppla in datorn till ett fungerande eluttag och tryck på strömbrytaren. • • • • 102 Kontrollera att huvudnätkabeln och frontpanelkabeln är ordentligt fastsatta i moderkortet.
Lampmönster Diagnostiklysdioder Problembeskrivning Felsökningssteg Strömbrytarlysdiod Minnesmoduler har upptäckts, men ett fel på minnesströmförsörjningen har uppstått. • • Om det finns två eller flera minnesmoduler installerade tar du bort modulerna, installerar sedan en modul och startar om datorn. Om datorn startar normalt fortsätter du att installera ytterligare minnesmoduler (en i taget) tills du har identifierat en felaktig modul eller installerat alla moduler utan fel.
Lampmönster Diagnostiklysdioder Problembeskrivning Felsökningssteg Strömbrytarlysdiod Ett möjligt fel på extrakort eller moderkort har uppstått. Ett möjligt fel på moderkortet har uppstått. Ta bort alla extrakort från PCI- och PCIe-kortplatserna och starta om datorn. Om datorn startar sätter du tillbaka korten ett i taget tills du hittar det felaktiga kortet. • • Ett möjligt fel på knappcellsbatteriet har uppstått. Koppla bort all intern och extern extrautrustning och starta om datorn.
Lampmönster Diagnostiklysdioder Problembeskrivning Felsökningssteg Strömbrytarlysdiod fungerande arbetsminne av samma typ i datorn. Ett möjligt grafikkortfel har uppstått. • • • Kontrollera att bildskärmen är ansluten till ett separat grafikkort. Ta bort och sätt tillbaka alla installerade grafikkort. Installera om möjlig ett fungerande grafikkort i datorn. Ett hårddiskfel kan ha inträffat. Ta bort och sätt tillbaka alla ström- och datakablar. Ett möjligt USB-fel har uppstått.
Lampmönster Diagnostiklysdioder Problembeskrivning Felsökningssteg Strömbrytarlysdiod Ett möjligt expansionskortfel har uppstått. • Kontrollera att det minne du använder stöds av datorn. • Kontrollera om det finns en konflikt genom att ta ut ett expansionskort (inte ett grafikkort) och starta om datorn (se ). Om felet kvarstår sätter du i kortet som du tog ut igen, tar sedan ut ett annat kort och startar om datorn. Upprepa processen för varje installerat expansionskort.
Lampmönster Diagnostiklysdioder Problembeskrivning Felsökningssteg Strömbrytarlysdiod • skärmen visar att det är problem med en enhet (exempelvis diskettenheten eller hårddisken), kontrollera den enheten för att undersöka om den fungerar korrekt. Om operativsystemet försöker starta från en enhet (exempelvis diskettenheten eller den optiska enheten) ska du kontrollera systeminställningsp rogrammet och se till att startsekvensen är den rätta för enheterna som är installerade i datorn.
• Alert! Operating in debug mode. Please populate memory in pairs for normal operation (Varning! Avbuggningsläge aktiverat. Fyll minnet parvis för normal drift.) • Alert! Power supply fan failure (Varning! Fel på strömförsörjningsfläkt). • Alert! Previous fan failure (Varning! Tidigare fläktfel). • Alert! Previous processor thermal failure (Varning! Tidigare termofel på processor).
47 Specifikationer OBS: Erbjudanden kan variera mellan olika regioner. Följande specifikationer är endast vad som enligt lag måste levereras med datorn. Mer information om datorns konfiguration får du om du klickar på Start → Hjälp och support och väljer alternativet att visa datorinformation. Tabell 1.
Tabell 5. Ljud Ljud Specifikation Inbyggt Realtek ALC3220 ljudkodek Tabell 6. Nätverk Nätverk Specifikation Inbyggt Intel 82579 och Intel 82574 Ethernet-styrenheter Tabell 7. Expansionsbuss Expansionsbuss Specifikation Busstyp: PCI Express 3.0 PCI Express 2.0 PCI 2.3 (tillval) SAS USB 2.0 SATA 3 Busshastighet: PCI: 133 MB/s PCI Express: • • • • PCIe 3.0 x16 platser dubbelriktad hastighet - 16 GB/s PCIe 3.0 x8 platser dubbelriktad hastighet - 8 GB/s PCIe 3.
Kortplatser Specifikation Kortplats 5 PCI Express 3.0 x8/x16 elektrisk/mekanisk, full höjd, full längd Kortplats 6 PCI Express 3.0 x16 elektrisk och mekanisk, full höjd, full längd Alternativ 2 för mittre förlängningskort: Kortplats 5 PCI 32b, 5V, full höjd och längd Kortplats 6 PCI Express 3.0 x16 elektrisk och mekanisk, full höjd, full längd Bakre I/O: Kortplats 7 PCI Express 2.0 x4/x16 elektrisk/mekanisk, halv höjd, halv längd Tabell 9.
Interna kontakter Specifikation Systemfläktar sex 4-stiftkontakter Fjärrströmstyrning av värdkort en 2-stiftskontakt CPU-/minnesström fyra fyrstiftskontakter Minne tolv 240-stiftskontakter (DDR3) Bakre I/O: PCI Express en 98-stiftskontakt (x8) Förlängningskort Yttre förlängningskort: PCI Express tre 164-stiftskontakter (x16) Alternativ 1 för mellersta förlängningskort PCI Express två 164-stiftskontakter (x16) Alternativ 2 för mittre förlängningskort: PCI en 120-stiftskontakt (32-bitars) PC
Kontroller och lampor Specifikation släckt (inget sken) — datorn har ingen fysisk anslutning till nätverket. Integritetslampor för nätverkslänk (baksida): grönt ljus — anslutningen mellan nätverket och datorn är 10 Mbps och fungerar bra. orange ljus — anslutningen mellan nätverket och datorn är 100 Mbps och fungerar bra. gul — anslutningen mellan nätverket och datorn är 1 000 Mbps och fungerar bra Lampor för nätverksaktivitet gul — blinkar när det finns aktivitet på nätverksanslutningen.
Miljöpåverkan Förvaring Specifikation -40 °C till 65 °C (-40 °F till 149 °F) Relativ luftfuktighet (maximal): Vid drift 10 till 90 % (utan kondens) Förvaring 5 till 95 % (utan kondens) Maximal vibration: Vid drift 5 till 350 Hz vid 0,0002 G2/Hz Förvaring 5 till 500 Hz vid 0,001 till 0,01 G2/Hz Maximal stöt: Vid drift 40 G +/- 5 % med pulsvaraktighet på 2 ms +/- 10 % (motsvarande 51 cm/sek) Förvaring 105 G +/- 5 % med pulsvaraktighet på 2 ms +/- 10 % (motsvarande 127 cm/sek) Luftburen förorenin
Systeminstallationsprogrammet 48 Startmeny Som i tidigare arbetsstationsplattformar innehåller datorn en engångsstartmeny. Den här funktionen tillhandahåller ett snabbt och bekvämt sätt att förbigå den i systeminstallationsprogrammet definierade startenhetsordningen och starta direkt från en angiven enhet (till exempel: diskett, CD-ROM eller hårddisk).
Dell Diagnostics Fabriksinstallerade plattformar innehåller ett 32-bitars systemdiagnostikprogram som är installerat på diagnostikpartitionen. Du kommer åt diagnostiken genom att trycka på under start och välja Diagnostics. Efter tangentnedtryckningen laddas de lämpliga modulerna och PSA-diagnostiken startar. Om inga fel upptäcks visas standardmenyn i Dell Diagnostics. När du avslutar diagnostiken startar systemet om och återgår till det installerade operativsystemet.
General (allmänt) Boot Sequence Anger den sekvens i vilken datorn försöker hitta ett operativsystem bland de enheter som anges i listan. • • • • • USB Floppy Drive (USB-diskettenhet) Hårddisk CD/DVD/CD-RW Drive (CD-/DVD-/CD-RW-enhet) Onboard or USB CD-ROM Drive (inbyggd CD-ROM-enhet eller USB CD-ROMenhet) USB Device (USB-enhet) Enheter Diskette Drive Anger hur diskettenheter konfigureras av BIOS • • SATA Operation Konfigurerar driftläget för den integrerade hårddiskstyrenheten.
Systemkonfiguration • • • Miscellaneous Devices Auto (standard) COM1 COM3 Aktiverar eller inaktiverar diverse enheter. • • • Främre USB Rear USB (bakre USB) Ljud Bild Primary Video Här kan användaren ange i vilken ordning systemet tilldelar den primära bildskärmsstyrenheten när det finns två eller flera bildskärmar. • • Styrenhet 1 Styrenhet 2 Prestanda Multi Core Support Anger huruvida datorn har en eller alla kärnor aktiverade.
Virtualiseringsstöd Virtualization Anger om en VMM (virtual machine monitor) kan utnyttja de ytterligare maskinvarumöjligheter som tillhandahålls av Intel Virtualization-tekniken. Enable Intel® Virtualization Technology (aktivera Intel® Virtualization-teknik) Aktiverat som standard. VT for Direct I/O Anger huruvida en VMM (Virtual Machine Monitor) kan utnyttja de ytterligare maskinvarufunktioner som tillhandahålls av Intel Virtualization-teknik för direkt I/O.
Säkerhet Chassis Intrusion Styr chassiintrångfunktionen. Du kan ställa in alternativet till: Clear Intrusion Warning (rensa intrångsvarning) — Aktiverat som standard Alternativen är tillgängliga när kryssrutan är markerad. • • • Disable (inaktivera) Enable (aktivera) On-Silent (på-tyst) — Aktiverat som standard (om chassiintrång upptäcks) Strömhantering AC Recovery Bestämmer vad som sker med systemet när nätspänningen slås på igen efter ett strömavbrott.
POST Behavior (självtestbeteende) Fast Boot Påskyndar startprocessen genom att ignorera vissa kompatibilitetssteg. Enable Fast Boot (aktivera snabbstart) — Aktiverat som standard Numlock LED Anger om Numlock-funktionen skall vara aktiverad vid start. Enable Numlock LED (aktivera Numlock-lysdioden) — Aktiverat som standard POST Hotkeys Anger om inloggningsskärmen visar ett meddelande med tangentsekvenserna för att öppna systeminstallationsprogrammet eller snabbstartsfunktionen.
Kontakta Dell 49 Kontakta Dell OBS: Om du inte har en aktiv Internet-anslutning kan du hitta kontaktinformationen på ditt inköpskvitto, förpackning, faktura eller i Dells produktkatalog. Dell erbjuder flera alternativ för support och service online och på telefon. Tillgängligheten varierar beroende på land och produkt och vissa tjänster kanske inte finns i ditt område. Gör så här för att kontakta Dell för försäljningsärenden, teknisk support eller kundtjänst: 1. Besök dell.com/support. 2.