Owners Manual
Table Of Contents
- Dell Precision Rack 7910 Owner's Manual
- Contents
- Working on your computer
- LCD panel features
- Hard drive indicator codes
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- System Overview
- Front bezel (optional)
- Removing the system cover
- Installing the system cover
- Inside the system
- Cooling shroud
- System memory
- General memory module installation guidelines
- Sample memory configurations
- Removing memory modules
- Installing memory modules
- Hard drives
- Removing a 2.5 inch hard-drive blank
- Installing a 2.5 inch hard-drive blank
- Removing Hard Drive
- Installing Hard Drive
- Removing a hard drive from a hard-drive carrier
- Installing a hard drive into a hard-drive carrier
- Optical drive (optional)
- Cooling fans
- Removing a cooling fan
- Installing a cooling fan
- Removing the cooling-fan assembly
- Installing the cooling-fan assembly
- Internal USB memory key (optional)
- Replacing the internal USB key
- PCIe card holder
- Cable retention bracket
- Expansion cards and expansion card risers
- Expansion card installation guidelines
- Removing an expansion card from expansion-card riser 2 or 3
- Installing an expansion card into the expansion-card riser 2 or 3
- Removing an expansion card from the expansion-card riser 1
- Installing an expansion card into the expansion-card riser 1
- Removing the riser 1 blank
- Installing the riser 1 blank
- Removing expansion-card risers
- Installing expansion-card risers
- GPU card installation guidelines
- Installing a GPU card
- Removing a GPU card
- SD vFlash media card (optional)
- Internal dual SD module (optional)
- Integrated storage controller card
- Network daughter card
- Heat sink and processor
- Power supply units
- Hot spare feature
- Removing the power supply unit blank
- Installing the power supply unit blank
- Removing an AC power supply unit
- Installing an AC power supply unit
- System battery
- Hard-drive backplane
- Removing the hard-drive backplane
- Installing the hard-drive backplane
- Control panel assembly
- System board
- Troubleshooting your system
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting iDRAC Direct (USB XML configuration)
- Troubleshooting iDRAC Direct (laptop connection)
- Troubleshooting a serial I/O device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting an internal USB key
- Troubleshooting an SD card
- Troubleshooting an optical drive
- Troubleshooting a hard drive
- Troubleshooting a storage controller
- Troubleshooting expansion cards
- Troubleshooting processors
- Error Messages
- System messages
- Using system diagnostics
- Jumpers and connectors
- Specifications
- System Setup
- Boot Menu
- Timing Key Sequences
- Dell Diagnostics
- About system setup
- Entering System Setup
- System Setup Main Menu
- System BIOS screen
- System Information screen details
- Memory Settings screen details
- Processor Settings screen details
- SATA Settings screen details
- Boot Settings screen details
- Integrated Devices screen details
- Serial Communication screen details
- System Profile Settings screen details
- System Security settings screen details
- Miscellaneous Settings screen details
- NIC indicator codes
- Power indicator codes
- Contacting Dell
NOTE: When two identical PSUs are installed, power supply redundancy (1+1 – with redundancy or 2+0 – without
redundancy) is configured in system BIOS. In redundant mode, power is supplied to the system equally from both PSUs
when Hot Spare is disabled. When Hot Spare is enabled, one of the PSUs will be put into standby when system utilization is
low in order to maximize efficiency.
NOTE: For AC power supply units, use only power supply units with the Extended Power Performance (EPP) label on the
back. Mixing power supply units from previous generations of servers can result in a power supply unit mismatch condition
or failure to power on.
Hot spare feature
Your system supports the hot spare feature that significantly reduces the power overhead associated with power supply
redundancy.
When the hot spare feature is enabled, one of the redundant PSUs is switched to the sleep state. The active PSU supports
100% of the load, thus operating at higher efficiency. The PSU in the sleep state monitors output voltage of the active PSU. If
the output voltage of the active PSU drops, the PSU in the sleep state returns to an active output state.
If having both PSUs active is more efficient than having one PSU in the sleep state, the active PSU can also activate the
sleeping PSU.
The default PSU settings are as follows:
● If the load on the active PSU is more than 50%, then the redundant PSU is switched to the active state.
● If the load on the active PSU falls below 20%, then the redundant PSU is switched to the sleep state.
You can configure the hot spare feature by using the iDRAC settings. For more information about iDRAC settings, see the
Integrated Dell Remote Access Controller User’s Guide at Dell.com/idracmanuals.
Removing the power supply unit blank
About this task
If you are installing a second power supply unit, remove the power supply unit blank in the bay by pulling the blank outward.
CAUTION:
To ensure proper system cooling, the power supply blank must be installed in the second power
supply bay in a non-redundant configuration. Remove the power supply blank only if you are installing a second
power supply.
Figure 36. Removing and installing the power supply blank
1. power supply blank
Installing and removing system components
67