Release Notes

• iSCSI interface is not displayed in Anaconda GUI
• Disabling SRIOV-vfs of Mellanox-ConnectX-4 cards results in terminal hang
• mei_me displays hardware start failed messages
• Intel - Sage Flat - ISCSI LUN is not discovered during Red Hat Enterprise Linux 7 OS installation
• Watchdog timer function did not work on Red Hat Enterprise Linux 7.2
• Recovery is not starting on RAID 01 virtual disk when I/Os are in progress
• Red Hat Enterprise Linux 7.3 displays an ACPI warning
• Red Hat Enterprise Linux 7.3 displays a mcelog error message
• IPv6 UEFI PXE installation fails
• Intel x520 FCoE first boot fails with kernel crash
• irqbalance spam messages with banned CPU conflict
• Coretemp driver adds a limited number of cores
• Turbostat displays incorrect information
• Ethtool reports a lower port speed
• Red Hat Enterprise Linux 7.3 displays an error message for drivers
• Mellanox ConnectX-4 NIC interfaces are named incorrectly
• Unable to read the Base Address Registers address logged in /var/log/messages
• Unable to detect a degraded S130 volume after the reboot
• Unable to install Red Hat Enterprise Linux 7 in the 16th hard drive slot by using unattended installation
• Red Hat Enterprise Linux 7 displays an error message related to network service in var/log/messages
• Unable to assign hot spare in Software RAID configuration when the virtual disk is in use
• ACPI displays warning message when system IO range conflicts
• DWS login fails in Red Hat Enterprise Linux 7.2
• Red Hat Enterprise Linux 7.2 displays a warning message in dmesg logs
• Invalid naming conventions for the Intel X710 card when NPAR or NPAR-EP is enabled
• Red Hat Enterprise Linux 7 displays an error message in /var/log/messages
• Unable to reboot Red Hat Enterprise Linux 7 after the successful installation on iSCSI or FC or FCoE
• Red Hat Enterprise Linux 7 displays an unknown netevent message during FCoE boot
• Ethtool offline test for network devices do not restore its previous state
• Installation on iSCSI LUN displays few unknown symbol messages
• NVMe devices are not identified during Red Hat Enterprise Linux installation
• Unable to restart Red Hat Enterprise Linux 7 after the successful installation on iSCSI LUN
• Red Hat Enterprise Linux 7 might not boot in the UEFI mode
• Installing Red Hat Enterprise Linux 7 by using the iDRAC Virtual Media does not resume if the iDRAC network is set to the
shared LOM mode
• Kernel panic occurs when OMSA services are started on Red Hat Enterprise Linux 7
• When Virtual Disk is not initialized, Red Hat Enterprise Linux 7 cannot be installed on 4k sector hard drives
• Invalid naming conventions for the ports of Emulex OneConnect OCe14102-UX-D card when NPAR-EP is enabled
• Unable to move soft link .desktop file
• Unable to boot Red Hat Enterprise Linux 7, when the Execute Disable option is disabled
• Unable to install Red Hat Enterprise Linux 7 in the UEFI mode
• While adding second slave to bond, it asks for connection type and shows additional connection types
• Loopback device is displayed as unknown in network settings
• Kernel panic on reboot or shutdown when Mellanox Team is setup
• PCIeSSDs report incorrect pciehp messages during boot
• VMM does not displays Windows Server 2012 in drop-down list
• Ethtool link test fails in Offline mode despite the cable being connected to the port
• PXE boot fails with a system crash when Red Hat Enterprise Linux 7 is installed on local storage and the tftp server has an
invalid boot EFI file
• NVMe driver reports I/O error on Surprise Removal or Surprise Insertion
• Reading EEPROM from a Broadcom device via ethtool results in soft lockup
• Error during the first boot on iSCSI disk
• Enabling SR-IOV virtual functions on both Intel and Mellanox cards result in invalid naming conventions for the network
devices
• Mellanox card does not display supported link modes as 40G
• Unable to install Red Hat Enterprise Linux 7 on a drive with an existing btrfs partition
• syslog displays error Related to network.service
14
Known issues