Dell S2721Q/S2721QS モニター ユーザーズ ガイド モデル:S2721Q/S2721QS 規定モデル:S2721Qb
注:「注」は、コンピューターをよりよく使いこなすための重要な情報を 表します。 注意:「注意」は指示に従わなければ、ハードウェアが故障する危険性、 またはデータが消失する危険性を示しています。 警告:「警告」は物件損害、人的被害または死亡の危険性を表します。 Copyright © 2020 Dell Inc. またはその子会社。複製を禁ず。Dell、EMC、その他の商標は、Dell Inc. またはその子会社の商標です。その他の商標の所有権は各社にあります。 2020 - 12 Rev.
目次 安全指示 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 製品の特徴. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 パッケージの内容 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 製品の特徴 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 部品とコントロールの確認 . . . . . . . . . . . . . . . . . . . . . . . . 10 正面図 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 背面図 . . . . . . . . . . . . . . . . . .
DisplayPort(DP 対 Dp)ケーブル ( 別売り ) と電源ケーブルを 接続する . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 ケーブルを調整する . . . . . . . . . . . . . . . . . . . . . . . . . . . . . モニターの電源を入れる . . . . . . . . . . . . . . . . . . . . . . . . . . ケンジントンロック(別売り)を使ってモニターを固定 する. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . モニタースタンドを取り外す -S2721Q . . . . . . . . . . . . . . . モニタースタンドを取り外す -S2721QS . . . . . . . . . . . . . . VESA 壁取り付け(別売り). . . . .
製品特有の問題 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 スピーカー特有の問題 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 付録 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 米国連邦通信委員会 (FCC) 通告(米国内のみ)および その他規制に関する情報 . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Dell へのお問い合わせ . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 エネルギーラベルおよび製品情報シートが記載された EU 製品データベース . . . . . . . . . . . . . . . . . . . . . . . . . . . .
安全指示 注意:このマニュアルで指定された以外のコントロール、調整、または手 順を使用すると、感電、電気的障害、または機械的障害を招く結果となり ます。 • 本製品は平坦な場所に置き、お取り扱いには十分注意してください。ス クリーンは落としたり、ぶつけたりすると破損しやすく、細心の取り扱 いが必要です。 • 本製品はお住まい地域の規準に従った電圧の AC 電源をお使いください。 • 本製品は室温に維持してください。極端な温度環境では、ディスプレイ の液晶に有害な影響を与える場合があります。 • 本製品を激しく揺ったり、強い衝撃を与えたりしないでください。自動 車のトランクに本製品を入れることなどが含まれます。 • 本製品を長期間ご使用にならない場合は、電源コードを外してください。 • 感電防止のために、カバーを外したり、本製品の内部に手を触れないよ うにしてください。 6 │ 安全指示
製品の特徴 パッケージの内容 モニターには、以下の表に示すコンポーネントがすべて付属しています。不 足しているコンポーネントがある場合は、Dell までお問い合わせください。詳 細は、Dell へのお問い合わせを参照してください。 注:一部のアイテムはオプションで、モニターに付属していません。機能 によっては、特定の国で使用できないものもあります。 注:スタンドを別途購入された場合は、そのスタンドの説明書にしたがっ て設置してください。 コンポーネント画像 コンポーネントの説明 ディスプレイ スタンドライザー: a. S2721Q b. S2721QS スタンド ベース: a. S2721Q b.
VESA™ ネジカバー (S2721Q のみ) 電源ケーブル(国により 異なります) HDMI ケーブル • クイック セットアップ ガイド • 安全、環境および規制 情報 8 │ 製品の特徴
製品の特徴 Dell S2721Q/S2721QS モニターにはアクティブ マトリックス、薄膜トランジ スター (TFT)、液晶ディスプレイ (LCD) および LED バックライトが搭載され ています。モニターの機能は、以下のようになっています: • 68.
部品とコントロールの確認 正面図 S2721Q S2721QS ラベル 1 2 説明 使用 機能ボタン 詳細は、モニターの操作を参照して ください。 電源オン / オフボタン(LED インジケーター付き) モニターをオン / オフにします。 10 │ 製品の特徴
背面図 S2721Q 背面図(モニターのスタンド付き) S2721QS 背面図(モニターのスタンド付き) ラベル 1 説明 使用 VESA 取り付け穴(100 mm x 100 mm - 接続された VESA カ バーの背面) VESA 互換の壁取付キットを使う壁 取付モニター (100 mm x 100 mm)。 製品の特徴 │ 11
2 バーコード、シリアル番号、 サービスタグ ラベル 技術サポートを受けるには、Dell にお問い合わせください。サービ スタグは、Dell 補修技術者がモニ ターに搭載されたハードウェアの コンポーネントを識別し、保証情 報を知るために付けられた、コン ポーネント毎に異なるアルファ ベットと数字による番号です。 3 スタンドリリースボタン スタンドをモニターから外します。 4 規制ラベル 規制承認を表示します。 5 ケーブル管理スロット ケーブルをスロットに通してケー ブル類を整理するために使います。 12 │ 製品の特徴
底面図 S2721Q モニタースタンドなし底面図 S2721QS モニタースタンドなし底面図 ラベル 1 2 説明 使用 セキュリティ ロック セキュリティ ロックでモニターを固定しま スロット す(セキュリティ ロックは含まれません)。 電源コネクター 電源ケーブルを接続します(モニター付 属) 。 製品の特徴 │ 13
3 HDMI ポート (HDMI 1) コンピューターに HDMI ケーブルを接続し てください(モニター付属)。 4 HDMI ポート (HDMI 2) コンピューターに HDMI ケーブルを接続し てください(モニター付属)。 5 DisplayPort コンピューターに DisplayPort ケーブルを接 続してください。 6 出力ポート スピーカーに接続してください。 注:このポートはヘッドフォンには対応し ていません。 7 スピーカー 14 │ 製品の特徴 オーディオ出力。
モニター仕様 モデル S2721Q スクリーン タイプ 有効マトリックス - TFT LCD パネルテクノロジー IPS アスペクト比 16:9 S2721QS 表示可能画像 対角 684.7 mm(27 インチ) 幅(有効エリア) 596.7 mm(23.49 インチ) 縦(有効エリア) 335.7 mm(13.21 インチ) 合計エリア 200301.8 mm2(310.47 インチ 2) ピクセル ピッチ 0.1554 x 0.
色の深さ 10.7 億色 色域 sRGB 99%(標準) 接続性 • 1 x DisplayPort バージョン 1.2 • 2 x HDMI ポートバージョン 2.0 • 1 x オーディオ出力ポート 境界幅(モニターの端からアクティブ エリアまで) 上 7.4 mm 左/右 7.4 mm/7.4 mm 下 21.
ビデオのサポートモード モデル S2721Q/S2721QS ビデオディスプレイ機能 (HDMI & DisplayPort) 480p、480i、576p、576i、720p、1080i、 1080p、QHD、UHD 事前設定ディスプレイ モード HDMI ディスプレイ モード ディスプレイ モード 水平周波数 (kHz) 垂直周波数 (Hz) 周波数 (MHz) 720 x 400 31.47 70.08 28.32 同期極 (水平 / 垂直) -/+ VESA、640 x 480 31.50 60.00 25.20 -/- VESA、640 x 480 37.50 75.00 31.50 -/- VESA、800 x 600 37.90 60.30 40.00 +/+ VESA、800 x 600 46.90 75.00 49.50 +/+ VESA、1024 x 768 48.40 60.00 65.00 -/- VESA、1024 x 768 60.00 75.00 78.
DP ディスプレイ モード ディスプレイ モード 水平周波数 (kHz) 垂直周波数 (Hz) 周波数 (MHz) 720 x 400 31.47 70.08 28.32 同期極 (水平 / 垂直) -/+ VESA、640 x 480 31.50 60.00 25.20 -/- VESA、640 x 480 37.50 75.00 31.50 -/- VESA、800 x 600 37.90 60.30 40.00 +/+ VESA、800 x 600 46.90 75.00 49.50 +/+ VESA、1024 x 768 48.40 60.00 65.00 -/- VESA、1024 x 768 60.00 75.00 78.80 +/+ VESA、1152 x 864 67.50 75.00 108.00 +/+ VESA、1280 x 1024 64.00 60.00 108.00 +/+ VESA、1280 x 1024 80.00 75.00 135.
電気的仕様 モデル S2721Q/S2721QS ビデオ入力信号 HDMI 2.0/DisplayPort 1.2、各差動線路毎に 600 mV、作 動ペアあたり 100 Ω 入力インピーダンス AC 入力電圧 / 周波 数 / 電流 100 VAC から 240 VAC / 50 Hz または 60 Hz ± 3 Hz / 1.5 A(標準) インラッシュ電流 • 120 V:30 A(最大)(0°C で)(コールドスタート) • 240 V:60 A(最大)(0°C で)(コールドスタート) 電源消費 • 0.2 W(オフモード)1 • 0.2 W(スタンバイモード)1 • 28.8 W(オンモード)1 • 52 W(最大)2 • 21.88 W (Pon)3 • 68.48 kWh (TEC)3 1 EU 2019/2021 および EU 2019/2013 に定義されるとおりです。 2 最大輝度とコントラスト設定。 3 Pon:オン モードの電源消費は、Energy Star 8.
物理特性 モデル S2721Q 信号ケーブル タイプ • デジタル:HDMI、19 ピン S2721QS • デジタル:DisplayPort、20 ピン(ケーブルは含ま れていません) 注:Dell モニターは、本機に付属するビデオケーブルを使用したときに最高 の性能を発揮するよう設計されています。Dell はこれ以外のケーブル製造会 社の製品について、素材、コネクター、これらのケーブルの生産工程等の点 において責任を負うことができません。そのため、Dell は Dell モニターに付 属しないケーブルのビデオ性能については保証いたしかねます。 寸法(スタンド付き) 高さ 453.4 mm(17.85 インチ) • 延長時: 510.1 mm(20.08 インチ) • 圧縮時: 400.1 mm(15.75 インチ) 幅 611.6 mm(24.08 インチ) 611.6 mm(24.08 インチ) 奥行き 186.8 mm(7.35 インチ) 174.7 mm(6.88 インチ) 高さ 364.6 mm (14.35 イン チ) 364.6 mm (14.
重量 重さ(パッケージ含 む) 8.1 kg (17.86 lb) 重さ(スタンド アセ 5.6 kg (12.35 lb) ンブリとケーブルを 含む) 重さ(スタンド アセ 4.7 kg (10.36 lb) ンブリなし)(壁取 付または VESA 取付 用 - ケーブルなし) スタンド アセンブリ 0.7 kg (1.54 lb) の重さ 9.2 kg (20.28 lb) 6.4 kg (14.11 lb) 4.7 kg (10.36 lb) 1.5 kg (3.
高度 運転時 5000 m (16404 ft)(最大) 非運転時 12192 m (40000 ft)(最大) 熱発散 • 177.43 BTU/ 時(最大) • 95.
19 ホットプラグ検出 Re-PWR 20 +3.3 V DP_PWR 18 HDMI コネクター ピン数 接続した信号ケーブルの 19 ピン側 1 TMDS データ 2+ 2 TMDS データ 2 シールド 3 TMDS データ 2- 4 TMDS データ 1+ 5 TMDS データ 1 シールド 6 TMDS データ 1- 7 TMDS データ 0+ 8 TMDS データ 0 シールド 9 TMDS データ 0- 10 TMDS クロック + 11 TMDS クロックシールド 12 TMDS クロック - 13 CEC 14 予約済み(デバイスの N.C.
18 +5 V 電源 19 ホットプラグ検出 LCD モニター品質とピクセルポリシー LCD モニターの製造プロセスにおいて、いくつかのピクセルが特定の状態に 固定されることはよくあります。見つけにくく、表示品質および使い勝手に 影響しません。Dell 社のモニターの品質とピクセルに関する方針の詳細は、 www.dell.com/pixelguidelines をご覧ください。 エルゴノミクス 注意:キーボードの不適切な、あるいは長時間にわたり使用は、体調不良 の原因となる場合があります。 注意:長時間モニタースクリーンを見続けると、眼精疲労の原因となりま す。 コンピュータの作業環境を整える際は、次のガイドラインに従って快適にお 使いください。 • コンピュータを操作するとき、体の真正面にキーボードとモニターを設 置します。キーボードを正しい位置に設置できる特殊な棚も市販されて います。 • モニターを長時間使用することから生じる目の疲れ、首 / 腕 / 背中 / 肩 の痛みを軽減するには、次のことをお薦めします。 1.
• 腰をしっかりとサポートできる椅子をお使いください。 • キーボードやマウスをお使いになるときには、手首が自然で快適な位置 になるように腕を水平に維持します。 • キーボードやマウスをお使いになるときには、手を休めるスペースを確 保してください。 • 上腕は両腕とも自然な位置に維持します。 • 両足は床にしっかりとつけます。 • 座った状態のときには、前傾姿勢にならないように重心を両足にかけま す。正しい姿勢を維持するために椅子の高さを調整するか、必要であれ ば足台をお使いください。 • 仕事の仕方よります。作業が長時間にならないように、仕事を管理する ようにしてください。定期的に休憩をとり、立ち上がったり、歩き回っ たりしてください。 • ケーブルや電源コードが快適な作業の邪魔にならないように、またこれ らに躓いたりしないように、机の下は常に整理しておいてください。 モニタースクリー ンは目の高さ、ま たは若干下に モニターと キーボードは 使用者の真正 面に 手首はまっす ぐゆったりと 足はしっかり と床に ディスプレイの取り扱いと移動 モニターを持ち上げたり、移動させたりする際は、次のガイドラ
• モニターを移動または持ち上げる前に、コンピュータとモニターの電源 を切ってください。 • モニターからすべてのケーブルを外します。 • モニターを最初に梱包されていた梱包材料に入れます。 • モニターを持ち上げたり、移動したりする際は、圧力をかけずにモニ ターの底面と側面をしっかりと持ちます。 • モニターを持ち上げたり、移動したりする際は、キズが付かないように スクリーンを外向きに持ち、ディスプレイエリアを押さないようにして ください。 • モニターを移送するときには、急激な振動を与えないようにしてくださ い。 26 │ 製品の特徴
• モニターを持ち上げたり、移動したりする際は、スタンドベースやスタ ンドライザーを持ってモニターを上下逆さにしないようにしてください。 モニターの故障やケガの原因となる場合があります。 保守のガイドライン モニターを洗浄する 注意:モニターの洗浄前には、安全指示を読み、その指示に従ってくださ い。 警告:モニターの洗浄前には、電源コンセントからモニター電源ケーブル を外してください。 最高の性能を引き出すために、モニターを開梱、洗浄、または操作している 間、以下のリストの指示に従ってください: • 静電気防止スクリーンを洗浄するには、柔らかい、きれいな布を水で軽 く湿らせてください。できれば、特殊スクリーン洗浄ティッシュまたは 静電気防止コーティングに適して溶液を使用してください。ベンゼン、 シンナー、アンモニア、研磨クリーナー、または圧縮空気は使用しない でください。 • ぬるま湯で軽く湿らせた布を使用して、モニターを洗浄します。合成洗 剤によりモニターの乳白色のフィルムがはがれることがあるため、合成 洗剤の使用は避けてください。 • モニターの梱包を開けている間に白いパウダーにお気づきになりました ら
モニターのセットアップ スタンドの取り付け -S2721Q 注:スタンドは出荷時には設置されていません。 注:次の手順は、モニター付属のスタンドを接続するための説明です。ス タンドを別途購入された場合は、そのスタンドの説明書にしたがって設置 してください。 モニタースタンドを取り付けるには: 1. 箱のふた部分に記載された指示に従って、スタンドを保護しているクッ ション材を取り外してください。 2.
3. スタンドライザーをスタンドベースに合わせます。 4. スタンドベースの底面にあるネジハンドルを起こし、右に回してスタン ドを安定させます。 5. ネジハンドルを閉じます。 6. ディスプレイの VESA スロットが見えるようにモニターの保護カバーを 開きます。 7.
8. VESA ネジカバーを閉めます。 9.
スタンドの取り付け -S2721QS 注:スタンドは出荷時には設置されていません。 注:次の手順は、モニター付属のスタンドを接続するための説明です。ス タンドを別途購入された場合は、そのスタンドの説明書にしたがって設置 してください。 モニタースタンドを取り付けるには: 1. 箱のふた部分に記載された指示に従って、スタンドを保護しているクッ ション材を取り外してください。 2. ゆっくりとスタンドベースとスタンドライザーを発砲スチロールから取 り出します。 3. スタンドライザーをスタンドベースに合わせます。 4. スタンドベースの底面にあるネジハンドルを起こし、右に回してスタン ドを安定させます。 5.
6. ディスプレイの VESA スロットが見えるようにモニターの保護カバーを 開きます。 7. スタンド アセンブリをディスプレイに取り付けます。 a. VESA スロットにスタンドライザーのつまみをスライドさせます。 b.
8. 両手でしっかりとスタンドライザーを持ち、モニターを持ち上げます。 次に、モニターを平たい場所にまっすぐに配置します。 注:事故を防止するために、モニターを持ち上げる際はスタンドライザー をしっかりと持ってください。 9.
モニターを接続する 警告:このセクションで手続きをはじめる前に、安全指示に従ってくださ い。 注:Dell モニターは、Dell 提供の同梱ケーブルと最適な状態で機能するよ うに設計されています。Dell は Dell 製でないケーブルを使用した場合の 映像品質および性能については保証いたしません。 注:ケーブルを接続する前に、ケーブルスロットにケーブルを通して整理 してください。 注:すべてのケーブルを同時にコンピューターに接続しないでください。 注:画像は、実例を示す目的で使用されます。コンピューターの外観は変 わることがあります。 モニターをコンピューターに接続する: 1. コンピューターの電源をオフにして、電源ケーブルを外します。 2.
DisplayPort(DP 対 Dp)ケーブル ( 別売り ) と電源ケーブルを接続する S2721Q S2721QS ケーブルを調整する S2721Q S2721QS モニターおよびコンピューターに必要なケーブルすべてを取り付けた後、 (ケーブルの取り付けについては、モニターを接続するを参照 してください) 上記のとおり、ケーブル管理スロットを使って、すべてのケーブルを適切に 調整します。 モニターのセットアップ │ 35
モニターの電源を入れる S2721Q S2721QS 36 │ モニターのセットアップ
ケンジントンロック(別売り)を使ってモニターを固定する セキュリティ ロックスロットはモニタの背面にあります。(セキュリティ ロックスロットを参照してください。) Kensington ロック(別売り)の使い方についての詳しい説明は、ロックの説 明書をお読みください。 Kensington セキュリティロックを使ってモニターをテーブルに固定します。 S2721Q S2721QS 注:画像は、実例を示す目的で使用されます。ロックの外観は変わること があります。 モニターのセットアップ │ 37
モニタースタンドを取り外す -S2721Q 注:台を取り外している間に LCD スクリーンに傷が付かないように、モ ニターは必ずきれいな面に置くようにしてください。 注:次の手順は、モニター付属のスタンドを取り外すための説明です。ス タンドを別途購入された場合は、そのスタンドの説明書にしたがって設置 してください。 スタンドを取り外すには: 1. 柔らかい布またはクッションの上にモニターを置きます。 2. ディスプレイの背面から VESA カバーを外すには、VESA カバーの窪みを 押します。 3. 長いねじ回しを使って、スタンドのすぐ上にある溝にある取り外し用の つまみを押します。 4.
モニタースタンドを取り外す -S2721QS 注:台を取り外している間に LCD スクリーンに傷が付かないように、モ ニターは必ずきれいな面に置くようにしてください。 注:次の手順は、モニター付属のスタンドを取り外すための説明です。ス タンドを別途購入された場合は、そのスタンドの説明書にしたがって設置 してください。 スタンドを取り外すには: 1. 柔らかい布またはクッションの上にモニターを置きます。 2. ディスプレイの背面にあるスタンド取り外しボタンを押したままにしま す。 3.
VESA 壁取り付け(別売り) S2721Q S2721QS (ネジの寸法:M4 x 10 mm) 。 VESA 互換壁取り付けキットに付いている使用説明書を参照してください。 1. ディスプレイを安定した平らなテーブルの軟らかい布またはクッション の上に置きます。 2. モニタースタンドを取り外します。( モニタースタンドを取り外す S2721Q および モニタースタンドを取り外す -S2721QS をお読みくださ い) 3. ねじ回しを使って、ディスプレイのバックカバーを固定している 4 個の ネジを外します。 4. 壁取り付けキットのブラケットをディスプレイに取り付けます。 5. モニターを壁に取り付けます。詳細は、壁取り付けキットの説明書をお 読みください。 注:18.
モニターの操作 モニターを電源オンにする 電源ボタンを押してモニターをオンにします。 前面パネルのコントロールを使う モニターの正面にあるボタンを使って、設定を調整してください。 正面パネルのボタンについては、次の表にまとめてあります: 正面パネルボタン 1 ショートカットキー / プリセットモード 説明 プリセット カラー モードのリストから選択す る際には、このショートカットを選択してく ださい。 音量スライダーに直接アクセスできます。 2 ショートカットキー / 音量 モニターの操作 │ 41
3 オンスクリーンディスプレイ (OSD) を開くに は、メニューボタンを使います。メニューシ ステムにアクセスするを参照してください。 メニュー 4 このボタンは、OSD メインメニューを終了す るときにも使用します。 終了 5 モニターをオン / オフにします。 電源 (電源ライトインジ ケーター付き) 白く点灯すると、モニターの電源が入ってお り性能が正常であることを意味しています。 白く点滅しているときには、モニターがスタ ンバイモード。 正面パネルボタン モニターの正面にあるボタンを使って、画像設定を調整してください。 正面パネルボタン 1 説明 上ボタンを押すと、OSD メニューのアイテムを調整 できます(範囲を広げます)。 上 2 下ボタンを押すと、OSD メニューのアイテムを調整 できます(範囲を狭めます)。 下 3 OK ボタンを使って、選択内容を確定します。 OK 4 戻るボタンを使用すると、前のメニューに戻りま す。 戻る 42 │ モニターの操作
オンスクリーンディスプレイ (OSD) メニューの使用 メニューシステムにアクセスする 注:設定を変えてから別のメニューに進んだり OSD メニューを終了した りすると、モニターはこれらの変更を自動的に保存します。設定を変更し てから OSD メニューが消えるのを待っても、変更は保存されます。 1. ボタンを押して OSD メニューを起動し、メイン メニューを表示しま す。 2. と ボタンを押して、設定オプション間を移動します。あるアイコ ンから別のアイコンに移動すると、オプション名がハイライト表示され ます。モニターで利用できるすべてのオプションについては、次の表を 参照してください。 3. または または ボタンを一度押すと、ハイライトされたオプ ションが有効になります。 注:表示された矢印ボタン(および OK ボタン)は選択したメニューに よっては異なる場合があります。ボタンを使って選択してください。 4. と ボタンを押して、目的のパラメーターを選択します。 5. を押してサブメニューに入り、メニューのインジケーターに基づき、 矢印ボタンを使って変更します。 6.
アイ コン メニューとサブ メニュー 説明 輝度 / コントラ スト このメニューを使って輝度 / コントラスト調整を 有効にします。 輝度 輝度は、バックライトの輝度を調整します。 輝度を上げるには 下げるには ボタンを押します。輝度を ボタンを押します(最小 0/ 最大 100)。 注:Smart HDR が有効であり、HDR コンテンツ が表示されているとき、輝度の手動調整は無効に なります。 コントラスト まず輝度を調整し、それでも調整が必要な場合の みコントラストを調整します。 ボタンを押してコントラストを上げ、 ボタ ンを押してコントラストを下げます(最小 0/ 最 大 100)。 コントラスト機能は、モニターの画面の暗い部分 と明るい部分の違いの程度を調整します。 44 │ モニターの操作
入力信号 入力信号メニューを使って、モニターに接続され たさまざまなビデオ信号を選択します。 DP DisplayPort (DP) コネクターを使用しているとき、 DP 入力を選択します。 ボタンを押して、選択 内容を確定します。 HDMI 1 HDMI コネクターを使用しているとき、HDMI 1 入 力を選択します。 ボタンを押して、選択内容を 確定します。 HDMI 2 HDMI コネクターを使用しているとき、HDMI 2 入力を選択します。 ボタンを押して、選択内容 を確定します。 自動選択 入力信号のリ セット これをオンにすると、仕様可能な入力信号をス キャンできます。 モニターの入力設定を工場出荷時の設定にリセッ トします。 モニターの操作 │ 45
色 プリセット モード 46 │ モニターの操作 色を使って色設定モードを調整します。 リストからプリセットモードを選択できます。
プリセットモー ド • 標準:モニターのデフォルトの色設定をロード します。これは、デフォルトのプリセットモー ドです。 • ComfortView:スクリーンから放射されるブ ルーライトのレベルを軽減させ、スクリーンを 見やすくします。 警告:モニターから放出されるブルーライトを 長時間見続けると、デジタルアイ、眼精疲労を 含め、目に影響を与えます。長時間モニターを 見続けると、首、腕、背中、肩など身体に痛み が生じる場合があります。詳細は、エルゴノミ クスを参照してください。 • ムービー:ムービーに適した色設定をロードし ます。 • FPS:ファーストパーソン・シューティング ゲーム (FPS) に適したカラー設定を読み込みま す。 • RTS:リアルタイムストラテジー ゲーム (RTS) に適したカラー設定を読み込みます。 • RPG:ロールプレイイング ゲーム (RPG) に適 したカラー設定を読み込みます。 • 暖色:低い色温度で色を再現します。画面は赤 / 黄の色合いで暖かく見えます。 • 寒色:高い色温度で色を再現します。画面は青 い色合いで冷たく見えます。 • ユーザーカラー:色設定を手動
入力カラー形式 ビデオ入力モードを次のように設定できます: • RGB:モニターが DisplayPort または HDMI ケーブルを使用してコンピューターまたはメ ディアプレーヤーに接続されている場合は、こ のオプションを選択します。 • YPbPr:メディアプレーヤーが YPbPr 出力し かサポートしていない場合は、このオプション を選択してください。 ボタンを押して、選択内容を確定します。 色相 この機能により、ビデオ画像の色は緑または紫に シフトします。色相は、望ましいフレッシュな色 調を調整するために使用されます。 または を使って色合いを「0」~「100」の範囲で調整し ます。 注:色相調整は、ムービー、FPS、RTS、RPG プリセットモードでのみ使用できます。 彩度 この機能は、ビデオ画像の色の彩度を調整しま す。 または を使って彩度を「0」~「100」 の範囲で調整します。 注:彩度調整は、ムービー、FPS、RTS、RPG プリセットモードでのみ使用できます。 色のリセット 48 │ モニターの操作 モニターの色設定を工場出荷時の設定にリセット します。
ディスプレイ ディスプレイメニューを使って画像を調整しま す。 アスペクト比 画像の比率はワイド 16:9、4:3、5:4 に設定でき ます。 注:PIP/PBP がアクティベートされているとき には、この機能は無効になります。 シャープネス この機能を使って、画像をよりシャープにまたは ソフトにします。 または を使ってシャープネスを「0」~ 「100」の範囲で調整します。 応答時間 暗さスタビライ ザー 応答時間を通常、高速、最速に設定できます。 暗めのゲームシナリオにおいて、見やすさを向上 させます。値を高くするほど (0 ~ 3)、表示された 映像の暗いエリアが見やすくなります。 注:Smart HDR または PIP/PBP がアクティベー トされているときには、この機能は無効になりま す。 モニターの操作 │ 49
Smart HDR Smart HDR(高ダイナミックレンジ)機能は、コ ントラスト、色域、明度を最適に調整することに よって、臨場感あふれる映像を出力します。デ フォルト設定はオフです。Smart HDR モードを 次のように設定できます: • デスクトップ:デスクトップコンピュータ一と 一緒にモニターを使用するときに選択します。 • ムービー HDR:HDR コンテンツを再生すると きに選択します。 • ゲーム HDR:HDR 対応ゲームを楽しむときに 選択します。リアルなシーンを再現し、ゲーム 体験をより臨場感あふれる映像として表示しま す。 注:モニターが HDR コンテンツを処理している 間は、プリセットモードおよび輝度は無効になり ます。 注:PIP/PBP がアクティベートされているとき には、この機能は無効になります。 画面のリセット 50 │ モニターの操作 すべてのディスプレイ設定を工場出荷時のプリ セット値にリセットします。
PIP/PBP この機能は別の入力ソースから取り込んだ画像が 表示されたウィンドウを映し出します。 メイン ウィンドウ DP HDMI 1 HDMI 2 サブウィンドウ DP HDMI 1 HDMI 2 X X 注:PBP モードでの画像は分割画面の中央に表示 されます。 モニターの操作 │ 51
PIP/PBP モード PIP/PBP (Picture in Picture/Picture by Picture) モー ドを PIP または PBP に調整します。オフを選択 すると、この機能が無効になります。 PIP I II PBP I PIP/PBP (サブ) II PIP/PBP サブウィンドウに用に、モニターに接続 できる他のビデオ信号を選択します。 ボタンを 押して、選択内容を確定します。 PIP サイズ PIP サブ画面のサイズを調整します。 注:このオプションは、PIP モードがオンの場合 にのみ使用できます。 52 │ モニターの操作
PIP の位置 PIP サブ画面の位置を調整します。 または を使うと、右上、左上、右下、左 下の中から選択できます。 ボタンを押して、選択内容を確定します。 注:このオプションは、PIP モードがオンの場合 にのみ使用できます。 ビデオ入れ替え PIP/PBP モードのメイン画面とサブ画面のビデオ を入れ替えます。 ボタンを押して、選択内容 を確定します。 オーディオ コントラスト (サブ) メインウィンドウかサブウィンドウからオーディ オ ソースを選択できます。 PIP/PBP モードで画像のコントラスト レベルを 調整します。 を使ってコントラストを上げ、 を使ってコ ントラストを下げます。 オーディオ 音量 スピーカーの音量を確認できます。 または を使って、音量レベルを「0」から 「100」の範囲で調整します。 スピーカー オーディオのリ セット スピーカーを有効または無効にします。 デフォルトの音設定に戻します。 モニターの操作 │ 53
メニュー 言語 透明度 このオプションを選択して、OSD の言語、メ ニューが画面に表示されている時間など、OSD の設定を調整します。 OSD ディスプレイを 8 つの言語(英語、スペイ ン語、フランス語、ドイツ語、ブラジルポルトガ ル語、ロシア語、簡体字中国語、日本語)の 1 つ に設定する言語オプション。 このオプションを選択し、 および ボタンを 押してメニュー透明化を変更します(最小 0 / 最 大 100)。 タイマー ボタンを最後に押してから OSD が有効になって いる時間の長さを設定します。 または を使ってスライダを 5 ~ 60 秒ま で、1 秒刻みで調整します。 54 │ モニターの操作
ロック モニターの制御ボタンをロックすると、他の人は 制御できなくなります。また、複数のモニターを 横に並べたとき、誤って操作してしまうのを防止 することもできます。 • メニュー ボタン:すべてのメニュー / 機能ボ タン(電源ボタンを除く)がロックされ、ユー ザーはアクセスできなくなります。 • 電源ボタン:電源ボタンだけがロックされ、 ユーザーはアクセスできなくなります。 • メニュー + 電源ボタン:メニュー / 機能ボタ ンと電源ボタンの両方がロックされ、ユーザー はアクセスできなくなります。 デフォルト設定はオフです。 他のロック方法 [ メニュー / 機能ボタン用 ]:電 源ボタンの横にあるメニュー / 機能ボタンを 4 秒 間押し続けても、ロックオプションを設定できま す。 注:ボタンをロック解除するには、電源ボタンの 横にあるメニュー / 機能ボタンを 4 秒間押し続け ます。 メニューのリ セット すべての OSD 設定を工場出荷時のプリセット値 にリセットします。 モニターの操作 │ 55
カスタマイズ ショートカット キー 1 ショートカット キー 2 プリセットモード、輝度 / コントラスト、入力信 号、アスペクト比、Smart HDR、PIP/PBP モー ド、音量の中から機能を選択し、ショートカット キーとして設定することができます。 LED 電源ボタン 節電のために、電源 LED インジケーターのオン / オフを設定できます。 高速復帰 デフォルト設定はオフです。オンを選択すると、 モニターはスタンバイモードに入りません。 モニターの正面パネルのボタンをどれでも押すと ( ボタン以外)、スタンバイモードに入ってい るモニターを復帰させる場合があります。 カスタマイズの リセット 56 │ モニターの操作 カスタマイズメニューですべての設定を初期値に 戻します。
その他 ディスプレー 情報 DDC/CI DDC/CI、LCD コンディショニングなど、OSD 設 定を調整する場合はこのオプションを選択しま す。 モニターの現在の設定が表示されます。 DDC/CI(ディスプレイ データチャンネル / コマ ンド インターフェイス)により、コンピュー ターのソフトウェアを介してモニターのパラメー ター(輝度、色バランスなど)を調整します。 オフを選択すると、この機能が無効になります。 ユーザー体験を最大限に高め、モニターのパ フォーマンスを最適にする場合、この機能を有効 にします。 モニターの操作 │ 57
LCD コンディ ショニング 画像保持の微細な問題を軽減します。画像保持の 程度によっては、プログラムが実行されるまでに 少し時間がかかることがあります。オンを選択す ることで、この機能を有効にできます。 サービスタグ モニターのサービスタグを表示します。このタグ は、Dell のホームページ等で電話サポートを依頼 したり、保証状況を確認したり、ドライバをアッ プデートしたりするときに必要です。 他をリセット その他メニューですべての設定を初期値に戻しま す。 工場リセット すべてのプリセット値を初期値に戻してくださ い。ENERGY STAR® テストの設定もあります。 58 │ モニターの操作
OSD 警告メッセージ モニターが特定の解像度モードをサポートしていないとき、次のメッセージ が表示されます: これは、モニターがコンピューターから受信している信号と同期できないこ とを意味します。このモニターが使用できる水平および垂直周波数幅につい ては、モニター仕様を参照してください。推奨モードは 3840 x 2160 です。 注:接続した入力信号によっては、メッセージが異なる場合があります。 DDC/CI 機能が無効になる前に、次のメッセージが表示されます: 初めて輝度レベルを調整するとき、次のメッセージが表示されます。 注:はいを選択すると、次回輝度設定を変更しようとしてもこのメッセー ジは表示されません。 モニターの操作 │ 59
初めて Smart HDR や高速復帰などの省エネ機能のデフォルト値を変更する と、次のメッセージが表示されます: 注:上記のいずれかの機能ではいを選択すると、次回これらの機能の設定 を変更しようとしてもこのメッセージは表示されません。初期値にリセッ トすると、メッセージが再度表示されます。 Smart HDR を有効してプリセットモードを変更しようとすると、次のメッ セージが表示されます: ロック機能が有効になる前に、次のメッセージが表示されます: 注:接続した設定によっては、メッセージが多少異なる場合があります。 モニターがスタンバイモードに入ると、次のメッセージが表示されます: 60 │ モニターの操作
コンピューターを有効にして、モニターを立ち上げ、OSD にアクセスします。 注:接続した入力信号によっては、メッセージが異なる場合があります。 OSD は、通常の動作モードでのみ機能します。スタンバイモードで電源ボタ ン以外のボタンを押すと、選択した入力によって次のメッセージが表示され ます: コンピューターがアクティブになり、モニターで OSD にアクセスできるよう になります。 注:接続した入力信号によっては、メッセージが異なる場合があります。 HDMI または DisplayPort 入力が選択されているが相当するケーブルが接続さ れていない場合、以下のような浮動ダイアログボックスが表示されます。 注:接続した入力信号によっては、メッセージが異なる場合があります。 工場リセットを選択すると、次のメッセージが表示されます: 詳細は、問題を解決するを参照してください。 モニターの操作 │ 61
最大解像度を設定する モニターの最大解像度を設定するには: Windows® 7、Windows® 8、Windows® 8.1: 1. Windows® 8 および Windows® 8.1 専用です。デスクトップ タイルを選択 して、元々のデスクトップに切り替えます。 2. デスクトップで右クリックして、画面の解像度をクリックします。 3. 画面の解像度のドロップダウン リストをクリックし、3840 x 2160 を選 択します。 4. OK をクリックします。 Windows® 10: 1. デスクトップ上を右クリックし、ディスプレイの設定をクリックします。 2. ディスプレイの詳細設定をクリックします。 3. 解像度のドロップダウン リストをクリックし、3840 x 2160 を選択しま す。 4. 適用をクリックします。 オプションとして 3840 x 2160 がない場合は、グラフィック ドライバを更新す る必要があります。コンピューターによっては、以下の手順のいずれかを完 了してください: Dell デスクトップまたはポータブル コンピューターをご使用の場合: • https://www.
HDR コンテンツを表示または再生するための要件 (1) Ultra BluRay DVD またはゲームコンソールを使う DVD プレーヤーまたはゲームコンソールが HDR 対応でなければなりません (Panasonic DMP-UB900、Xbox One S、PS4 Pro など) 。 (2) PC を使う HDMI2.0a(HDR オプション付き)対応ポートなど、HDR 対応のグラフィッ クカードをお使いになり、HDR グラフィックドライバがインストールして あることを確認してください。HDR 対応アプリケーション(Cyberlink PowerDVD 17 、 Windows 10 Movies & TV アプリなど)をお使いください。 注:Dell デスクトップコンピューターやノートブックコンピューターに HDR コンテンツの再生に対応する最新のグラフィックドライバをダウン ロードしてインストールするには、https://www.dell.com/support/drivers をご覧ください。 NVIDIA NVIDIA 製 HDR 対応グラフィックカードは、www.nvidia.
傾き、旋回、垂直に伸ばす 注:次の手順は、モニター付属のスタンドを接続するための説明です。ス タンドを別途購入された場合は、そのスタンドの説明書にしたがって設置 してください。 モニターにスタンドを取り付けると、モニターを最も快適な角度に調整する ことができます。 傾き S2721Q S2721QS 注:出荷時には、スタンドは設置されていません。 旋回(S2721QS のみ) 64 │ モニターの操作
垂直に伸ばす(S2721QS のみ) 注:スタンドは、垂直に最大 110 mm 伸ばせます。下の図で、伸ばし方を 示します。 ディスプレイを回転させる(S2721QS のみ) ディスプレイを回転させる前に、ディスプレイが垂直に延ばされているか、 またモニターの底部エッジの傾きを避けるために傾けてあるか確認してくだ さい。 モニターの操作 │ 65
右回転 左回転 注:Dell コンピューターでディスプレイ回転機能(横対縦表示)を使用す るには、このモニターに含まれていない最新のグラフィックスドライバが 必要です。最新のグラフィックスドライバをダウンロードして更新するに は、www.dell.
システムのディスプレイ回転設定の調整 モニターを回転させた後、以下の手順でシステムのディスプレイの回転設定 を調整する必要があります。 注:Dell コンピューター以外でモニターを使用している場合、グラフィッ プスドライバのウェブサイトまたはお使いのコンピューターの製造元ウェ ブサイトに進み、オペレーティングシステムの回転についての情報を確認 します。 ディスプレイの回転設定を調整するには: 1. デスクトップ上を右クリックした後、プロパティをクリックします。 2. 設定タブを選択し、詳細設定をクリックします。 3. ATI グラフィックスカードを使っている場合は、回転タブを選択して、 お気に入りの回転を設定します。 4. NVIDIA グラフィックスカードを使っている場合は、NVIDIA タブをク リックして、左カラムで NVRotate を選択し、次にお気に入りの回転を 選択します。 5.
問題を解決する 警告:このセクションで手続きをはじめる前に、安全指示に従ってくださ い。 自己テスト お使いのモニターには、自己テスト機能が装備され、適切に機能しているか どうかを確認できます。モニターとコンピューターが適切に接続されていて、 モニター スクリーンが暗い場合は、次の手順でモニター自己テストを実行し てください: 1. コンピューターとモニター両方の電源をオフにする。 2. コンピューターからビデオ ケーブルを外す。 3. モニターの電源をオンにする。 モニターがビデオ信号を検知できないが正しく作動している場合、画面に浮 動ダイアログ ボックスが(黒い背景に)表示されます。自己テストモードで は、電源 LED が白になります。また、選択した入力によって、下に表示され るダイアログの 1 つが画面上をスクロールし続けます。 または 4.
5. モニターの電源をオフにして、ビデオ ケーブルを再接続し、次にコン ピューターとモニター両方の電源をオンにします。 前の手順を行った後もモニター スクリーンに何も表示されない場合、モニ ターが適切に機能していないため、ビデオ コントローラーおよびコンピュー ターをチェックしてください。 内蔵診断 モニターには内蔵の診断ツールが付属しており、発生している画面の異常が モニターに固有の問題か、またはコンピューターやビデオ カードに固有の問 題かを判断します。 内蔵診断を実行するには、以下の手順に従います: 1. 画面がきれいであること(または、画面の表面に塵粒がないこと)を確 認します。 2. ポップアップメニューが表示されるまでボタン 4 を約 4 秒押し続けます。 3. ボタン 1 またはボタン 2 を使って診断ツール を選択し、ボタン 3 で 確定します。診断プログラムの最初でグレイのテストパターンが表示さ れます。 4. 画面に異常がないか、慎重に検査します。 5. 再度ボタン 1 を押して、テストパターンを変更します。 6.
よくある問題 次の表には、発生する可能性のあるモニターのよくある問題と考えられる解 決策に関する一般情報が含まれます: 一般的な症状 ビデオなし / 電源 LED オフ 発生した問題 実行可能な解決策 画像が表示され • コンピューターにモニターを接続して ない いるビデオ ケーブルが適切に接続さ れ、しっかり固定されていることを確 認します。 • 他の電気機器を使用して、コンセント が正しく機能していることを確認しま す。 • 電源ボタンが完全に押されていること を確認します。 • 入力信号メニューにより適切な入力信 号が選択されていることを確認してく ださい。 ビデオなし / 電源 LED オン 画像なし、また • OSD によって、輝度とコントラスト コ は輝度がない ントロールを増加します。 • モニター自己診断テスト機能チェック を実行します。 • ビデオ ケーブル コネクター に曲がっ たり破損したピンがないか、チェック します。 • 内蔵診断を実行します。 • 入力信号メニューにより適切な入力信 号が選択されていることを確認してく ださい。 フォーカスが 弱い • ビデオ拡張ケーブ
ビデオが揺れ たり / ずれた りする 画像が波打った • モニターを工場出荷時設定にリセット り、微妙にぶれ します。 る • 環境係数をチェックします。 • モニターの場所を変えて、他の部屋で テストします。 ピクセルが抜 けている LCD スクリーン • サイクル電源オン - オフ。 に点が入る • 永久的にオフになっているピクセルが ありますが、これは LCD テクノロジに 固有の欠陥です。 • Dell 社のモニターの品質とピクセルに 関する方針の詳細、詳細については、 Dell サポート www.dell.com/ pixelguidelines. ドット落ち LCD スクリーン • サイクル電源オン - オフ。 に明るい点が • 永久的にオフになっているピクセルが 入る ありますが、これは LCD テクノロジに 固有の欠陥です。 • Dell 社のモニターの品質とピクセルに 関する方針の詳細、詳細については、 Dell サポート www.dell.com/ pixelguidelines.
水平 / 垂直ラ イン スクリーンに複 • モニターを工場出荷時設定にリセット 数の線が入る します。 • モニター自己テスト機能チェックを行 い、これらの線が自己テストモードで も入るかどうかを確認します。 • ビデオ ケーブル コネクター に曲がっ たり破損したピンがないか、チェック します。 • 内蔵診断を実行します。 同期化の問題 スクリーンがス • モニターを工場出荷時設定にリセット します。 クランブル状態 か、磨り減って • モニター自己テスト機能チェックを行 見える い、スクランブル状態のスクリーンが 自己テストモードでも入るかどうかを 確認します。 • ビデオ ケーブル コネクター に曲がっ たり破損したピンがないか、チェック します。 • セーフモードでコンピューターを再起 動します。 安全関連問題 スモークまたは • トラブルシューティング手順を実行し ないでください。 スパークの明ら かな症状 • 直ちに Dell にご連絡ください。 断続的問題 モニターの誤作 • コンピューターにモニターを接続して 動をオンおよび いるビデオケーブルが適切に接続され、 オフ しっかり固
色が欠けてい る 画像の色が欠け • モニター自己診断テスト機能チェック ている を実行します。 • コンピューターにモニターを接続して いるビデオケーブルが適切に接続され、 しっかり固定されていることを確認し ます。 • ビデオ ケーブル コネクター に曲がっ たり破損したピンがないか、チェック します。 色違い 画像の色が正し • アプリケーションによって、色メ くない ニュー OSD のプリセットモードの設定 を変更します。 • 色メニュー OSD のユーザーカラーで R/G/B 値を調整してください。 • 内蔵診断を実行します。 長時間モニ ターに静止画 像を表示した ために起こる 画像の焼き付 き 表示された静止 • スクリーンが無作動状況になってから、 数分でスクリーンがオフになるように 画像のかすかな 設定します。これらの設定は、 影が画面に表示 Windows 電源オプションまたは Mac 省 される エネルギー設定で調整できます。 • または、動的に変わるスクリーンセー バーを使用します。 製品特有の問題 一般的な症状 発生した問題 実行可能な解決策 スクリーン画 画像がス
• モニターの電源をオフにして、電源コー 正面パネル上 OSD がスク ドを外し、もう一度コードを差して、電 のボタンで、 リーン上に表示 源を入れます。 モニターを調 されない 整できない • OSD メニューがロックされます。電源ボ タンの横にあるメニュー / 機能ボタンを 4 秒間押し続けるとロック解除できます (詳細は、ロックを参照してください)。 ユーザコント 画像が表示され • 信号ソースをチェックします。マウスを 動かすかキーボードのどれかのキーを押 ロールを押し ず、LED が白く して、コンピューターが省電力モードに ても入力信号 点灯 入っていないことを確認します。 がない • 信号ケーブルが正しく差し込まれている かどうかをチェックします。必要に応じ て、信号ケーブルを差し込み直してくだ さい。 • コンピューターまたはビデオプレーヤー を再起動します。 ピクチャが画 ピクチャを画面 • DVD の異なるビデオ形式により、モニ ターが全画面で表示できないことがあり 面全体に表示 の高さまたは幅 ます。 されない いっぱいに表示 できない • 内蔵診断を実行します。 スピーカー特有の問題
付録 警告: 安全指示 警告:このマニュアルで指定された以外のコントロール、調整、または手 順を使用すると、感電、電気的障害、または機械的障害を招く結果となり ます。 安全についての説明は、安全、環境および規制情報 (SERI) をご覧ください。 米国連邦通信委員会 (FCC) 通告(米国内のみ)およびその他規 制に関する情報 米国連邦通信委員会 (FCC) 通告(米国内のみ)およびその他規制に関する情 報に関しては、規制コンプライアンスに関するウェブページ www.dell.com/ regulatory_compliance をご覧ください。 Dell へのお問い合わせ 米国のお客様の場合、800-WWW-DELL (800-999-3355) にお電話ください。 エネルギーラベルおよび製品情報シートが記載された EU 製品 データベース S2721Q:https://eprel.ec.europa.eu/qr/344898 S2721QS:https://eprel.ec.europa.