Dell SP2318H/SP2418H 显示器 用户指南 管制型号:SP2318H、 SP2418H
注、注意和警告 注:“ 注 ” 表示可以帮助您更好使用计算机的重要信息。 注意:“ 注意 ” 表示如果不遵循说明操作可能会损坏硬件或导致数据丢失。 警告:“ 警告 ” 表示可能会造成财产损失、人身伤害或死亡。 版权所有 © 2017-2019 Dell Inc. 保留所有权利。本产品受美国和国际版权法和知识产权法的保护。 Dell™ 和 Dell 标志为在美国和 / 或其它司法管辖地的商标。本文中提到的所有其它标志和名称可能是 其它公司的商标。 2019 - 04 Rev.
目录 关于本显示器 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 包装物品 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 产品特性 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 识别零部件及控制装置 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 正视图 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 后视图 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
设置您的显示器 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 连接支架 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 连接显示器 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 连接 VGA 电缆 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 连接 HDMI 电缆 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 连接 DisplayPort (DP 到 DP)电缆 (选配). . . . . . . . . . . . . . . . . 30 连接 USB 3.0 电缆 . . . . . .
附录 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 FCC 声明 (仅针对美国)和其它管制信息 . . . . . . . . . . . . . 59 中国能源效率标识 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 联系 Dell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
关于本显示器 包装物品 您的显示器配有下表中的部件。请检查是否收到所有部件,如有部件遗漏请联 系 Dell。 注:某些物品为选配件,因此您的显示器中可能不包括这些物品。在某些国 家,可能不提供某些功能或者媒体。 注:如要安装第三方支架,参阅相应的支架安装指南以了解安装说明。 显示器 机架提升器 6 │ 关于本显示器
基座 电源电缆 (视国家而有所不同) VGA 电缆 HDMI 电缆 USB 3.
产品特性 Dell SP2318H/SP2418H 平板显示器采用有源矩阵技术、薄膜晶体管 (TFT)、 液晶显示屏 (LCD) 和 LED 背光。显示器特性包括: • SP2318H:58.4 厘米 (23 英寸)可视区域 (对角线测量)。 分辨率:通过 VGA、 DisplayPort 和 HDMI 最高可达 1920 x 1080,支持全屏 或低分辨率。 • SP2418H:60.5 厘米 (23.8 英寸)可视区域 (对角线测量)。 分辨率:通过 VGA、 DisplayPort 和 HDMI 最高可达 1920 x 1080,支持全屏 或低分辨率。 • 色域 72% NTSC。 • 倾斜、旋轴、高度和旋转调节功能。 • 可拆卸支架和视频电子标准协会 (VESA™) 100 mm 安装孔,可实现灵活的 安装方案。 • 与 DisplayPort 和 HDMI 的数据连接。 • 配备了 1 个 USB 上游端口和 4 个 USB 下游端口。 • 即插即用功能 (如果您的系统支持)。 • 屏幕显示 (OSD) 调节,便于设置和优化屏幕。 • 安全锁槽。 • 支架锁。 • 处于睡眠模式时待机功率为 0.
识别零部件及控制装置 正视图 前面板控制部件 标签 1 描述 功能按钮 (详情参见操作显示器) 2 电源开 / 关按钮 (带 LED 指示灯) 关于本显示器 │ 9
后视图 后视图 (包括显示器支架) 标签 1 描述 使用 VESA 安装孔 (100 mm x 壁挂式显示器采用兼容 VESA 的壁 100 mm - 位于连接外盖后部) 挂安装套件 (100 mm x 100 mm)。 2 认证标签 列出了认证准许。 3 支架卸下按钮 可从显示器松开支架。 4 安全锁槽 用安全锁固定显示器 (不含安全 锁)。 5 条形码、序列号、和服务标签 如果您需要联系 Dell 寻求技术帮 助,请参考这个标签。 6 Dell Soundbar 安装支架插槽 用于连接选配的 Dell Soundbar。 注:在安装 Dell Soundbar 之前,请 撕掉安装槽上的塑料条。 7 10 │ 电缆管理槽 关于本显示器 用于将电缆有条理地安装在槽内。
侧视图 标签 1 描述 USB 下游端口 使用 连接 USB 设备。 注:要使用此端口,必须将 USB 电 缆 (随显示器提供)连接到显示器 和计算机上的 USB 上游端口。 关于本显示器 │ 11
底视图 底视图 (无显示器支架) 标签 1 描述 使用 电源电缆连接器 连接电源电缆。 2 HDMI 端口 用 HDMI 电缆连接计算机。 3 DisplayPort 用 DP 电缆连接计算机。(不包括线 缆) 4 支架锁功能 使用 M3 x 6 mm 螺丝将支架锁定到 显示器 (不包括螺丝)。 5 VGA 连接器 用 VGA 电缆连接计算机。 6 USB 上游端口 将 USB 电缆 (随显示器提供)连接 到此端口和计算机,以启用显示器 上的 USB 端口。 7 USB 下游端口 连接 USB 设备。 注:要使用此端口,必须将 USB 电 缆 (随显示器提供)连接到显示器 和计算机上的 USB 上游端口。 12 │ 关于本显示器
显示器规格 型号 SP2318H 屏幕类型 有源矩阵 - TFT LCD 面板技术 平面转换技术 16:9 宽高比 SP2418H 可视图像 对角线 水平、有效显示区域 584.20 mm (23 英寸) 604.52 mm (23.8 英寸) 垂直、有效显示区域 286.42 mm (11.28 英寸) 296.46 mm (11.67 英寸) 区域 145839.33 mm2 (226.05 英寸 2) 156246.27 mm2 (242.18 英寸 2) 像素点距 0.265 mm x 0.265 mm 0.275 mm x 0.275 mm 每英寸像素 (PPI) 96 93 视角 178° (垂直)典型 509.18 mm (20.05 英寸) 527.04 mm (20.
连接 • 1 x DP 1.2 • 1 x HDMI 1.4 • 1 x VGA • 1 x USB 3.0 端口 - 上游 • 2 x USB 3.0 端口 - 侧面 • 2 x USB 2.0 端口 - 底部 边缘宽度 (显示器边 缘至显示区域) 11.4 mm (上 / 左 / 右) 18.
预设显示模式 显示模式 水平频率 (kHz) 垂直频率 (Hz) 像素时钟 (MHz) VESA、 640 x 480 31.5 60.0 25.2 同步极性 (水平 / 垂直) -/- VESA、 640 x 480 37.5 75.0 31.5 -/- IBM、 720 x 400 31.5 70.0 28.3 -/+ VESA、 800 x 600 37.9 60.0 40.0 +/+ VESA、 800 x 600 46.9 75.0 49.5 +/+ VESA、 1024 x 768 48.4 60.0 65.0 -/- VESA、 1024 x 768 60.0 75.0 78.8 +/+ VESA、 1152 x 864 67.5 75.0 108.0 +/+ VESA、 1280 x 1024 64.0 60.0 108.0 +/+ VESA、 1280 x 1024 80.0 75.0 135.0 +/+ VESA、 1600 x 900 60.0 60.0 108.
实际特性 型号 SP2318H 信号电缆类型 • 模拟:D-Sub、 15 针 • 数字:DisplayPort、 20 针 (不包括线缆) SP2418H • 数字:HDMI、 19 针 • 通用串行总线:USB、 9 针 尺寸 (包括支架) 高度 (伸展时) 487.1 mm (19.17 英寸) 492.1 mm (19.37 英寸) 高度 (收缩时) 357.1 mm (14.06 英寸) 362.1 mm (14.26 英寸) 宽度 532.0 mm (20.94 英寸) 549.8 mm (21.65 英寸) 深度 180.0 mm (7.09 英寸) 180.0 mm (7.09 英寸) 高度 315.9 mm (12.43 英寸) 326.0 mm (12.83 英寸) 宽度 532.0 mm (20.94 英寸) 549.8 mm (21.65 英寸) 深度 50.3 mm (1.98 英寸) 50.3 mm (1.98 英寸) 高度 (伸展时) 400.8 mm (15.78 英寸) 400.8 mm (15.
支架装置的重量 2.10 kg (4.63 磅) 2.10 kg (4.63 磅) 前面板光泽 2-4 2-4 SP2318H SP2418H 环境特性 型号 兼容标准 • 取得 ENERGY STAR 认证的显示器 • 兼容 RoHS • 无 BFR/PVC 显示器 (除外接电缆) • 无砷玻璃和无汞 (仅限面板) 温度 工作 0°C 至 40°C (32°F 至 104°F) 非工作 • 存放:-20°C 至 60°C (-4°F 至 140°F) • 运输:-20°C 至 60°C (-4°F 至 140°F) 湿度 工作 10% 至 80% (无冷凝) 非工作 • 存放:5% 至 90% (无冷凝) • 运输:5% 至 90% (无冷凝) 海拔 工作 5,000 m (16,404 英尺)(最大值) 非工作 12,192 m (40,000 英尺)(最大值) 散热量 • 129.66 BTU/ 小时 (最大值) • 133.07 BTU/ 小时 (最大值) • 61.42 BTU/ 小时 (典型值) • 64.
电源管理模式 如果您的 PC 机中安装了符合 VESA DPM™ 规定的显卡或者软件,显示器可自动 降低非使用状态时的功耗。这种功能称为省电模式 *。计算机检测到键盘、鼠标 或者其它输入设备的输入信号时,显示器自动恢复运行。下表显示了这种自动 节能功能的功耗和信号。 SP2318H VESA 模式 水平同步 垂直同步 正常运行 活动 活动 视频 活动 电源 指示灯 白色 功耗 38 W (最大值) ** 18 W (典型值) 活动关闭 模式 非活动 非活动 空白 白色 (闪烁) 低于 0.3 W 关闭 - - - 关 低于 0.3 W 功耗 Energy Star Pon 14.8 W ETEC 46.7 kWh SP2418H VESA 模式 水平同步 垂直同步 正常运行 活动 活动 视频 活动 电源 指示灯 白色 功耗 39 W (最大值) ** 19 W (典型值) 活动关闭 模式 非活动 非活动 空白 白色 (闪烁) 低于 0.3 W 关闭 - - - 关 低于 0.
Energy Star 功耗 Pon 18.5 W ETEC 54.1 kWh 只有在正常运行模式下,才能使用 OSD。在活动关闭模式下按任何按钮时,将 出现以下信息: 激活计算机和显示器以访问 OSD 菜单。 注:根据连接的输入信号,信息可能略有不同。 注:本显示器有 ENERGY STAR 认证。 注: Pon:启动模式的功耗按 Energy Star 7.0 版本中的定义。 ETEC:以 kWh 为单位的总能耗按 Energy Star 7.
针脚分配 VGA 连接器 针脚编号 1 20 已连接信号电缆的 15 针一端 视频 - 红色 2 视频 - 绿色 3 视频 - 蓝色 4 GND 5 6 自检 GND-R 7 GND-G 8 GND-B 9 计算机 5 V/3.
DisplayPort 连接器 针脚编号 1 已连接信号电缆的 20 针一端 ML0(p) 2 GND 3 ML0(n) 4 ML1(p) 5 GND 6 ML1(n) 7 ML2(p) 8 GND 9 ML2(n) 10 ML3(p) 11 GND 12 ML3(n) 13 GND 14 GND 15 AUX(p) 16 GND 17 AUX(n) 18 GND 19 Re-PWR 20 +3.
HDMI 连接器 针脚编号 1 22 已连接信号电缆的 19 针一端 TMDS 数据 2+ 2 TMDS 数据 2 屏蔽线 3 TMDS 数据 2- 4 TMDS 数据 1+ 5 TMDS 数据 1 屏蔽线 6 TMDS 数据 1- 7 TMDS 数据 0+ 8 TMDS 数据 0 屏蔽线 9 TMDS 数据 0- 10 TMDS 时钟信号 + 11 TMDS 时钟信号屏蔽线 12 TMDS 时钟信号 - 13 CEC 14 预留 (未连接) 15 DDC 时钟信号 (SCL) 16 DDC 数据 (SDA) 17 DDC/CEC 接地 18 +5 V 电源 19 热插拔检测 │ 关于本显示器
即插即用功能 您可在任何兼容即插即用功能的系统中安装该显示器。显示器可使用显示数据 通道 (DDC) 协议自动为计算机提供扩展显示标识数据 (EDID),使系统可自行配 置并优化显示器的设置。大多数显示器的安装过程都自动执行;如果需要,您 可选择不同的设置。关于更改显示器设置的详情,请参见操作显示器。 通用串行总线 (USB) 接口 本节介绍显示器上的 USB 端口。 注:本显示器兼容超高速 USB 3.0 和高速 USB 2.0。 传输速度 超高速 数据传输率 5 Gbps 4.5 W (每个端口的最大值) 高速 480 Mbps 4.5 W (每个端口的最大值) 全速 12 Mbps 4.5 W (每个端口的最大值) 传输速度 功耗 高速 数据传输率 480 Mbps 功耗 2.5 W (每个端口的最大值) 全速 12 Mbps 2.5 W (每个端口的最大值) 低速 1.5 Mbps 2.5 W (每个端口的最大值) USB 3.
5 SSTX- 6 SSTX+ 7 GND 8 SSRX- 9 SSRX+ USB 3.
USB 2.0 下游连接器 针脚编号 1 连接器的 4 针一端 VCC 2 DMD 3 DPD 4 GND USB 端口 • 1 x USB 3.0 上游 - 底部 • 2 x USB 2.0 下游 - 底部 • 2 x USB 3.0 下游 - 侧面 注:USB 3.0 功能要求使用兼容 USB 3.0 的计算机。 注:显示器的 USB 接口只有在显示器已开启或者在省电模式中才可使用。 如果关闭显示器后重新开机,连接的外围设备可能需要数秒时间才可继续正 常工作。 液晶显示器质量和像素规定 在液晶显示器生产过程中,某个或者多个像素有时会保持不变状态,这些像素 很难发现,而且不会影响显示器质量或者功能。有关 Dell 显示器质量和像素规 定,详情请访问 Dell 支持站点:http://www.dell.
维护指导 清洁显示器 注意:在清洁显示器之前,请阅读并遵守安全说明。 警告:在清洁显示器之前,从电源插座上拔下显示器的电源电缆。 在拆除包装、清洁或者搬运显示器时,应遵守以下最佳操作说明: • 如需清洁防静电屏幕,用水稍稍蘸湿柔软、干净的抹布。如果可能,请使 用适用于防静电涂层的专用屏幕清洁纸巾或溶液。请勿使用汽油、稀释 剂、氨水、磨蚀性清洁剂或者压缩空气。 • 如需清洁显示器,请用温水稍稍蘸湿抹布。不可使用任何类型的清洁剂, 因为某些清洁剂会在显示器表面上留下乳状薄膜。 • 如果在拆除显示器包装时发现白色粉末,可用抹布擦除。 • 在搬运显示器时应谨慎小心,因为颜色较深的显示器在划伤时会显示出比 浅色显示器更明显的白色划痕。 • 为使显示器达到最佳显示质量,请使用动态变化的屏幕保护程序,在不使 用时请关闭显示器。 26 │ 关于本显示器
设置您的显示器 连接支架 注:在交付显示器时,支架并未安装。 注:这适用于带支架的显示器。如购买了第三方的支架时,参阅相应的支架 安装指南以了解安装说明。 在连接显示器支架时: 1. 按纸盒口封上的说明,将支架从将其固定的顶部缓冲垫中取出。 2. 将基座突出体完全插入支架插孔。 3. 抬起螺栓把手,并顺时针旋转螺栓。 4.
5. 掀起保护袋 (如图所示)以露出 VESA 区域以组装支架。 6. 将支架装置连接到显示器上。 a. 将显示器背面的凹槽对准支架上部的两个扣件。 b. 按压支架,直到扣入定位。 7.
连接显示器 警告:在您开始执行本节的任何操作之前,请遵守安全说明。 注:在连接之前,通过电缆管理槽整理电缆。 注:请勿同时将所有的电缆连接到计算机上。 在连接显示器到计算机时: 1. 关闭计算机并断开电源电缆。 2.
连接 DisplayPort (DP 到 DP)电缆 (选配) 注:图片仅供示意说明。计算机的外观可能有所不同。 连接 USB 3.0 电缆 完成 VGA/DP/HDMI 电缆的连接之后,按照以下步骤将 USB 3.0 电缆连接到计 算机并完成显示器设置: 1. 将上游 USB 3.0 端口 (供应的线缆)连接到计算机上适当的 USB 3.0 端 口。(详情请参见底视图。) 2. 将 USB 3.0 外围设备连接到显示器的下游 USB 3.0 端口。 3. 将计算机和显示器的电源电缆插入附近的插座。 4. 开启显示器和计算机。 如果显示器显示图像,表示安装已经完成。如果没有显示图像,请参见通 用串行总线 (USB) 特定问题。 5.
整理电缆 在显示器和计算机连接所有必要的电缆之后,(关于电缆连接请参见连接显示 器),有条理地设置上述所有电缆。 拆卸显示器支架 注:为避免在拆卸支架时划伤液晶显示屏,必须将显示器放在干净柔软的表 面上。 注:这适用于带支架的显示器。如购买了其它的支架时,请参阅相应的支架 安装指南以了解安装说明。 设置您的显示器 │ 31
在拆卸支架时: 1. 将显示器放在软布或软垫上。 2. 按住支架卸下按钮。 3. 从显示器位置向上提起支架。 墙面安装 (选配) (螺丝尺寸:M4 x 10 mm)。 请参考说明书,该说明书与符合 VESA 的壁挂安装套件放在一起。 1. 将显示器面板放置在平稳桌面上的软布或衬垫上。 2. 移除支架。 3. 使用十字头螺丝刀卸掉塑料后壳的四个螺丝。 4. 将墙面安装包中的安装支架安装到显示器上。 5. 根据与墙面安装包一起附送的说明书将显示器安装到墙上。 注:只能使用 UL 认证的壁挂支架,并且最小承受重量 / 负载为 3.06 公斤 (SP2318H)/3.
操作显示器 打开显示器电源 按 按钮开启显示器。 使用前面板控制部件 使用显示器正面的控制按钮调节显示图像的特性。在使用这些按钮调节控制装 置时, OSD 会显示正在更改的数值。 下表说明前面板按钮: 前面板按钮 描述 使用此按钮可以从预设颜色模式列表中选择。 1 快捷键 / 预设模式 操作显示器 │ 33
使用此按钮可从连接到显示器的视频信号列表中 进行选择。 2 快捷键 / 输入源 使用菜单按钮可以启动屏幕显示 (OSD) 并选择 OSD 菜单。请参考访问菜单系统。 3 菜单 使用此按钮返回到主菜单或退出 OSD 主菜单。 4 退出 使用电源按钮开关显示器。 5 电源 (包括电源指示灯) 白灯表示显示器为开,并工作正常。闪烁的白色 指示灯表示处于省电模式。 前面板按钮 使用显示器前面的按钮调整图像设置。 前面板按钮 描述 使用向上按钮调节 (增加范围) OSD 菜单中的项目。 1 向上 使用向下按钮调节 (减少范围) OSD 菜单中的项目。 2 向下 使用确定按钮确认 OSD 菜单中的选择。 3 确定 使用返回按钮回到前一菜单。 4 返回 34 │ 操作显示器
使用屏幕显示 (OSD) 菜单 访问菜单系统 注:如果您更改了设置,随后继续到另一个菜单或退出 OSD 菜单,显示器 会自动保存所做更改。如果您更改了设置,并等待 OSD 菜单消失,所做更 改也会保存。 1.
数字 (DP) 输入的主菜单 注:只有在您使用模拟 (VGA) 连接器时才能使用自动调节。 2. 按 和 按钮在设置选项之间移动。当从一个图标移动到另一个图标 时,会突出显示选项名称。请参考以下表格了解本显示器可用的所有选项 之完整列表。 按钮以激活突出显示的选项。 3. 按一次 4. 按 和 按钮可选择需要的参数。 5. 按 按钮进入滑块,然后根据菜单上的指示使用 更改。 6.
图标 菜单和子菜单 描述 亮度 / 对比度 使用此菜单激活亮度 / 对比度调整。 亮度 亮度可以调整背光的亮度。 按 按钮可以提高亮度,按 度 (最小 0 / 最大 100)。 按钮可以降低亮 注:在开启动态对比时,将禁用手动调节亮度。 对比度 先调整亮度,如果需要进一步调整,再调整对比 度。 按钮可以提高对比度,按 按 对比度 (最小 0 / 最大 100)。 按钮可以降低 对比度可以调整显示器屏幕暗度和亮度之间的差异 程度。 操作显示器 │ 37
自动调节 尽管计算机会在启动时识别本显示器,但自动调节 功能可以根据您的特定设置优化显示器设置。 自动调节可使显示器能够根据输入的视频信号自动 调节。使用自动调节之后,通过使用显示设置下的 像素时钟 (粗略)和相位 (精细)控制项进一步微 调显示器。 注:在很多情况下,自动调节可根据您的配置调节 出最佳画质。 注:只有在您使用模拟 (VGA) 连接器时才能使用自 动调节。 38 │ 操作显示器
输入源 使用输入源菜单,在可能连接到显示器上的不同视 频信号之间进行选择。 VGA 当使用模拟 (VGA) 连接器时,选择 VGA 输入。按 选择 VGA 输入源。 DP HDMI 当使用 DisplayPort (DP) 连接器时,选择 DP 输入。 选择 DisplayPort 输入源。 按 当使用 HDMI 连接器时,选择 HDMI 输入。按 选择 HDMI 输入源。 自动选择 重置输入源 颜色 打开此功能可让您扫描可用的输入源。 将显示器的输入设置重新设为出厂设置。 使用颜色可调整颜色设置模式。 操作显示器 │ 39
预设模式 在选择预设模式时,可以从列表中选择标准、 ComfortView、多媒体、电影、游戏、暖色、冷色 或自定颜色。 • 标准:加载显示器的默认颜色设置。这是默认的 预设模式。 • ComfortView:降低屏幕放出的蓝光量,以使观 看时眼睛更舒服。 • 多媒体:为多媒体应用加载理想的颜色设置。 • 电影:为电影加载理想的颜色设置。 • 游戏:为大多数游戏应用加载理想的颜色设置。 • 暖色:增加色温。使用红色 / 黄色色调,屏幕颜 色偏暖色。 • 冷色:减少色温。使用蓝色色调,屏幕颜色偏冷 色。 • 自定颜色:允许手动调节颜色设置。 使用 或 按钮,调节三种颜色 (红、绿、 蓝)值,并创建自己预置的颜色模式。 40 │ 操作显示器
输入颜色格式 允许您将视频输入模式设置为: RGB:如果您的显示器使用 DP 或 HDMI 电缆连接 到了计算机 (或 DVD 播放机),请选择此选项。 YPbPr:如果您的 DVD 播放器仅支持 YPbPr 输出, 则选择此选项。 色调 此功能可以将视频图像的颜色改为绿色或紫色。通 常用于将颜色调整到需要的肤色调。使用 或 将色调从 “0” 调整到 “100”。 使用 增加视频图像的绿色程度。 使用 增加视频图像的紫色程度。 注:仅在选择电影或游戏预设模式时才可以使用色 调调节。 饱和度 此功能可以调整视频图像的颜色饱和度。使用 或 将饱和度从 “0” 调整到 “100”。 使用 增加视频图像的颜色显示。 使用 增加视频图像的单色显示。 注:仅在选择电影或游戏预设模式时才可以使用饱 和度调节。 重置颜色 将显示器的颜色设置重新设为出厂设置。 操作显示器 │ 41
显示 宽高比 水平位置 使用显示来调整图像。 将图像宽高比调节为宽高比 16:9、 4:3 或 5:4。 使用 或 左右调整图像。最小为 “0“(-)。 最大为 “100“(+)。 垂直位置 使用 或 上下调整图像。最小为 “0“(-)。 最大为 “100“(+)。 注:水平位置和垂直位置调整只能用于 “VGA” 输 入。 清晰度 此功能可使图像看起来更清晰或更柔和。 使用 像素时钟 将清晰度从 “0” 调整到 “100”。 相位和像素时钟调整可使您根据个人偏好调整显示 器。 使用 相位 或 或 调整到最佳图像质量。 如果使用相位调整并未取得满意的结果,可使用像 素时钟 (粗略)调整,然后再使用相位 (精细)。 注:像素时钟和相位调整只能用于 “VGA” 输入。 动态对比 可增强对比度,呈现更加清晰细致的图像质量。 使用 按钮可开启或关闭动态对比。 注:在选择游戏或电影预设模式时,动态对比可以 提供较高的对比度。 42 │ 操作显示器
响应时间 让您将响应时间设置为普通或快速。 重置显示器 选择此选项,恢复默认显示器设置。 显示器电源 LED 电源按钮 让您设置开启或关闭电源 LED 指示灯以节能。 USB 让您在显示器处于待机模式时启用或禁用 USB 功 能。 注:待机模式下时启用或禁用 USB,仅在 USB 上游 电缆拔出时适用。当 USB 上游电缆插入时,此选项 将无法选取。 重置能量 菜单 选择此选项,恢复默认显示器电源设置。 选择此选项可调整 OSD 的设置,例如 OSD 的语言、 菜单显示在屏幕上的时间总长等。 操作显示器 │ 43
语言 语言选择可将 OSD 显示设置为八种语言之一 (英 语、西班牙语、法语、德语、巴西葡萄牙语、俄 语、简体中文或日语)。 旋转 逆时针 90 度旋转 OSD。您可以按照显示器旋转调 整菜单。 透明度 选择此选项,可通过按 和 按钮来改变菜单 的透明度 (最小 0 / 最大 100)。 定时器 可让您设置按下显示器的按钮后 OSD 保持活动的时 间。 使用 或 以 1 秒增量调整滑杆,范围从 5 到 60 秒。 锁 控制用户使用调整功能。当选择锁时,不允许用户 进行调整。所有按钮都被锁定。 注: 解锁功能 - 只可使用硬件解锁 (按住电源按钮旁边 的按钮 6 秒钟)。 闭锁功能 - 可使用软件锁定 (通过 OSD 菜单),也 可使用硬件锁定 (按住电源按钮旁边的按钮 6 秒 钟)。 44 │ 重置菜单 将所有 OSD 设置重置为出厂预设值。 个性设置 用户可以从预设模式、亮度 / 对比度、自动调节、 输入源、宽高比或旋转中选择一项功能,并将其设 置为快捷键。 操作显示器
其他 选择此选项可调整 OSD 设置,如 DDC/CI、 LCD 调 节等。 DDC/CI DDC/CI (显示数据通道 / 命令接口)允许通过计 算机上的软件程序调整显示器参数 (亮度、颜色平 衡等)。您可以选择禁用以禁用此功能。启用此功 能以获得最佳的显示器用户体验和性能。 操作显示器 │ 45
LCD 调节 有助于减少微小的图像残留现象。根据图像残留的 程度,程序运行或许需要一些时间。您可以选择启 用以启用此功能。 重置其它设置 在其他菜单下可将所有的设置重设回出厂预设值。 工厂重置 将所有设置重置为出厂预设值。 注:该显示器有一个内置功能,可以自动校准亮度以补偿 LED 老化。 OSD 警告消息 当启用动态对比功能时 (在这些预设模式中:游戏或电影),将禁用手动调节 亮度。 在显示器不支持特定的分辨率模式时,会显示以下信息: 46 │ 操作显示器
这表示显示器无法与从计算机接收的信号同步。关于本显示器支持的水平和垂 直频率,请参见显示器规格。推荐模式为 1920 x 1080。 在禁用 DDC/CI 功能之前,会显示以下信息: 在显示器进入省电模式时,显示以下信息: 激活计算机并唤醒显示器以访问 OSD。 根据选定的输入,如果按下电源按钮之外的任一按钮,会显示以下信息: 注:根据连接的输入信号,信息可能略有不同。 如果选择了 VGA、 HDMI 或 DP 输入,并且相应的电缆均未连接,则会显示下面 所示的浮动对话框。 或 操作显示器 │ 47
或 详情请参见故障排除。 设置最大分辨率 要为显示器设置最大分辨率: 在 Windows® 7、 Windows® 8 和 Windows® 8.1: 1. 仅适用于 Windows® 8 和 Windows® 8.1,选择桌面平铺以切换到经典桌 面。 2. 在桌面上右击并选择屏幕分辨率。 3. 单击屏幕分辨率的下拉列表并选择 1920 x 1080。 4. 点击确定。 在 Windows® 10: 1. 在桌面上右击并选择显示设置。 2. 单击高级显示设置。 3. 单击分辨率的下拉列表并选择 1920 x 1080。 4.
如果您没有看到 1920 x 1080 选项,那么您可能需要更新您的图形卡驱动程序。 根据使用的计算机,可采用以下方法: 如果使用 Dell 台式机或者笔记本计算机: • 进入 http://www.dell.
垂直展开 注:支架的垂直展开高度最大为 130 mm。下图显示了如何垂直展开支架。 旋转显示器 在旋转显示器之前,显示器在垂直方向上应完全展开 (垂直展开)并向上完全 倾斜以免碰撞显示器的底边。 50 │ 操作显示器
注:如需在 Dell 计算机中使用显示器旋转功能 (横向与纵向模式),需要 更新显卡驱动程序 (非该显示器的附件)。如需下载图形卡驱动程序, 请访问 www.dell.com/support 并查看下载部分是否有最新更新的视频驱 动程序。 注:在纵向模式中,在使用图形卡要求较高的应用程序时性能可能会有所降 低 (3D 游戏等等)。 调节系统的旋转显示设置 旋转显示器之后,需要完成以下步骤以调节系统的旋转显示器设置。 注:如果显示器使用非 Dell 主机,您需要访问图形卡驱动程序网站或者您 的计算机制造商网站,以了解关于相关操作系统中的显示器旋转信息。 如需调节旋转显示器设置: 1. 在桌面上右击并选择属性。 2. 选择设置选项卡,并单击高级。 3. 如果使用 ATI 显卡,选择旋转选项卡并设置所需的旋转参数。 4. 如果使用 nVidia 显卡,单击 nVidia 选项卡,在左侧栏中选择 NVRotate, 然后选择所需的旋转参数。 5.
故障排除 警告:在您开始执行本节的任何操作之前,请遵守安全说明。 自检 显示器提供自检功能,可用于检查显示器是否功能正常。如果显示器和计算机 已经正确连接,但显示器屏幕不显示任何内容,按照以下步骤运行自检功能: 1. 关闭计算机和显示器。 2. 从计算机的背面拔下视频电缆。 3.
4. 如果视频电缆断开或者损坏,系统的正常运行过程中也会显示该对话框。 5. 关闭显示器并重新连接视频电缆;然后开启计算机和显示器。 如果在执行以上步骤之后您的显示器屏幕仍然显示空白,检查您的视频控制器 和计算机,因为您的显示器功能正常。 内置诊断功能 您的显示器配有内置诊断工具,可帮助您确定显示屏的异常是由显示器本身的 问题还是计算机和图形卡造成的。 注:只有在拔下视频电缆且显示器处于自检模式中时才可运行内置诊断 功能。 如需使用内置诊断功能: 1. 保持屏幕干净 (屏幕表面没有灰尘)。 2. 从计算机或者显示器的背面拔下视频电缆。此后显示器进入自检模式。 3. 同时按住前面板的按钮 1,保持 5 秒钟。将显示一个灰色画面。 4. 仔细检查屏幕是否存在异常。 5. 再次按下前面板的按钮 1。画面的颜色变为红色。 6. 检查显示器是否存在任何异常。 7.
常见问题 下表列出了可能遇到的一些显示器常见问题及其解决办法。 常见症状 无视频 / 电源 LED 指示灯关闭 您遇到的问题 无图像 可能的解决方案 • 确保连接显示器和计算机的视频电 缆已经正确连接。 • 使用其它任何电气设备检查电源插 座是否功能正常。 • 确保已经完全按下电源按钮。 • 确定已通过输入源菜单选择了正确 的输入源。 无视频 / 电源 LED 指示灯开启 无图像或无亮度 • 使用 OSD 提高亮度和对比度。 • 执行显示器自检功能。 • 检查视频电缆连接器中的针脚是否 弯曲或者折断。 • 运行内置诊断功能。 • 确定已通过输入源菜单选择了正确 的输入源。 对焦不正确 图像模糊或有 重影 • 使用 OSD 执行自动调节功能。 • 使用 OSD 调整相位和像素时钟。 • 去除视频延长线。 • 将显示器复位至出厂设置。 • 将视频分辨率改为正确的宽高比。 视频抖动 图像或视频摇摆 • 使用 OSD 执行自动调节功能。 • 使用 OSD 调整相位和像素时钟。 • 将显示器复位至出厂设置。 • 检查环境条件。 • 改变显示器安装位置,在其它房间 中测试。 54 │ 故障排除
像素缺失 液晶显示屏有 斑点 • 重新启动。 • 因受到液晶显示器技术的限制,亮 点像素属于正常缺陷。 • 有关 Dell 显示器质量和像素规定, 详情请访问 Dell 支持站点: http://www.dell.com/support/ monitors。 固定像素 液晶显示屏有 亮点 • 重新启动。 • 因受到液晶显示器技术的限制,亮 点像素属于正常缺陷。 • 有关 Dell 显示器质量和像素规定, 详情请访问 Dell 支持站点: http://www.dell.
同步问题 屏幕显示杂乱 图像 • 将显示器复位至出厂设置。 • 使用 OSD 执行自动调节功能。 • 使用 OSD 调整相位和像素时钟。 • 执行显示器自检功能,确定在自检 模式中是否出现杂乱的图像。 • 检查视频电缆连接器中的针脚是否 弯曲或者折断。 • 在安全模式中重启计算机。 安全须知 出现烟雾或火花 • 不得执行任何故障排除操作。 • 请立即联系 Dell。 间歇性问题 开关时显示器出 现故障 • 确保连接显示器至计算机的视频电 缆已经正确连接。 • 将显示器复位至出厂设置。 • 执行显示器自检功能,确定在自检 模式中是否出现间歇性问题。 颜色缺失 图像颜色缺失 • 执行显示器自检功能。 • 确保连接显示器至计算机的视频电 缆已经正确连接。 • 检查视频电缆连接器中的针脚是否 弯曲或者折断。 颜色错误 图像颜色不佳 • 根据应用程序,在颜色 OSD 菜单中 更改预设模式的设置。 • 在颜色 OSD 菜单中的自定颜色下调 整 R/G/B 值。 • 运行内置诊断功能。 因显示器上长期 停留静态图像而 导致图像残留 静态图像在屏幕 上残留暗影 • 使用电源管理功能在不使用时
产品特定问题 特定症状 屏幕图像过小 您遇到的问题 可能的解决方案 图像在屏幕正中, • 在显示的 OSD 菜单中检查宽高比设 但没有填满整个显 置。 示区 • 将显示器复位至出厂设置。 无法使用前面板的 屏幕上不显示 按钮调整显示器 OSD • 关闭显示器,拔下并重新插回电源电 缆,然后打开显示器。 • 检查 OSD 菜单是否被锁定。若是, 按住电源按钮上方的按钮 6 秒钟解锁 (参见锁)。 按下用户控制按钮 没有画面,LED 灯 • 检查信号源。移动鼠标或者按键盘上 时显示没有输入信 显示白色 的任意键,确定计算机不在省电模式 号 中。 • 检查信号电缆是否已经正确插入。如 果必要可重新连接信号电缆。 • 重启计算机或者视频播放机。 图像没有填满整个 图像无法达到屏幕 • 由于 DVD 使用不同的视频格式 (宽 屏幕 的最大高度或者宽 高比),显示器可全屏显示。 度 • 运行内置诊断功能。 注:在选择 HDMI/DP 模式时,自动调节功能不可用。 故障排除 │ 57
通用串行总线 (USB) 特定问题 特定症状 USB 接口不工作 您遇到的问题 USB 外围设备不 工作 可能的解决方案 • 检查显示器是否已经开启。 • 将上游电缆重新连接到计算机。 • 重新连接 USB 外围设备 (下游连接 器)。 • 关闭并重新开启显示器。 • 重新启动计算机。 • 某些 USB 设备 (例如外置硬盘驱动 器需要较高电流);将设备直接连接 到计算机系统。 超高速 USB 3.0 接 超高速 USB 3.0 外 • 检查计算机是否兼容 USB 3.0。 口速度缓慢 围设备工作速度缓 • 某些计算机同时配置 USB 3.0、 USB 慢或者根本不工作 2.0 和 USB 1.1 端口。确保使用正确的 USB 端口。 • 将上游电缆重新连接到计算机。 • 重新连接 USB 外围设备 (下游连接 器)。 • 重新启动计算机。 当 USB 3.0 设备插 入后,无线 USB 外围设备将停止 工作 无线 USB 外围设 • 增长 USB 3.
附录 警告: 安全说明 警告:如果不按本文档所述使用控件、进行调整或执行其它任何过程,可能 导致电击、触电和 / 或机械伤害。 有关安全说明的信息,请参阅安全、环境与规章信息 (SERI)。 FCC 声明 (仅针对美国)和其它管制信息 关于 FCC 声明和其它管制信息,请参见管制符合性网站,网址是 www.dell.com/regulatory_compliance。 中国能源效率标识 根据中国大陆 << 能源效率标识管理办法 >> 本显示器符合以下要求: 生产者名称 戴尔 (中国)有限公司 戴尔 (中国)有限公司 规格型号 SP2318H SP2418H 能效等级 2级 2级 ≥ 1.5 ≥ 1.5 ≤ 0.50 ≤ 0.50 能源效率 (cd/W) 关闭状态功率 (W) 睡眠状态功率 (W) 产品类型 依据国家标准 ≤ 0.50 ≤ 0.