Dell Storage MD1400 인클로저 하드웨어 소유자 매뉴얼 September 2019 개정 A01
참고, 주의 및 경고 노트: "주"는 컴퓨터를 보다 효율적으로 사용하는 데 도움을 주는 중요 정보를 제공합니다. 주의: "주의"는 하드웨어 손상이나 데이터 손실의 가능성을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: "경고"는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험이 있음을 알려줍니다. © 2014 ~ 2019 Dell Inc. 또는 자회사. 저작권 본사 소유. Dell, EMC 및 기타 상표는 Dell Inc. 또는 자회사의 상표입니다. 기타 상표는 각 소유자의 상표 일 수 있습니다.
목차 장 1: 인클로저 정보...........................................................................................................................5 외관 사양................................................................................................................................................................................5 전면 패널 기능 및 표시등................................................................................................................................................... 5 전면 베젤 기능 및 표시등...........
장 3: 인클로저 문제 해결................................................................................................................. 29 안전 제일 — 사용자 및 인클로저를 위함..................................................................................................................... 29 인클로저 스타트 업 오류 문제 해결............................................................................................................................... 29 통신 단절 문제 해결............................................................................
1 인클로저 정보 주제: 외관 사양 전면 패널 기능 및 표시등 전면 베젤 기능 및 표시등 하드 디스크 드라이브 표시등 패턴 후면 패널 기능 및 표시등 인클로저 관리 모듈 전원 표시등 코드 기타 필요한 정보 • • • • • • • • 외관 사양 표 1. 인클로저 치수 및 중량 치수 값 높이 8.7cm(3.43인치) 너비 48.2cm(18.98인치) 깊이 - PSU 손잡이 포함 59.2cm(23.3인치) 중량 - 최대 구성 시 28.39kg(62.58lb) 중량 - 비어 있을 경우 9.0kg(19.8lb) 전면 패널 기능 및 표시등 그림 1 . 전면 패널 기능 및 표시등 항목 표시등, 단추 또는 커 넥터 아이콘 설명 1 시스템 ID 단추 전면 제어판의 시스템 식별 단추를 사용하여 랙 안의 특정 인클로저를 찾을 수 있습니다. 단추를 누르면 제어판 및 EMM 컨트롤러 모듈의 시스템 상태 표시등 이 단추를 다시 누를 때까지 청색으로 깜박입니다.
항목 표시등, 단추 또는 커 넥터 3 인클로저 상태 LED 아이콘 설명 인클로저 전원이 켜진 경우 인클로저 상태 LED가 켜집니다. 정상적으로 작동하는 동안에는 청색으로 켜집니다. 호스트 서버에서 인클로저를 식별하거나 시스템 식별 단추를 누른 경우 청색으 로 깜박입니다. 황색 표시등이 황색으로 깜박이거나 몇초간 황색으로 켜진후 EMM이 시작 또는 재설정시에 꺼집니다. 인클로저가 경고 상태인 경우 장시간 황색으로 깜박입니다. 인클로저가 오류 상태인 경우 황색으로 켜집니다. 4 하드 디스크 드라이브 최대 12개의 3.5인치 SAS 핫 스왑 가능 하드 디스크 드라이브. 전면 베젤 기능 및 표시등 그림 2 . 전면 베젤 기능 및 표시등 항목 표시등, 단추 또는 아이콘 커넥터 설명 1 인클로저 상태 LED 인클로저 전원이 켜진 경우 인클로저 상태 LED가 켜집니 다. 그림 3 . 시스템이 정상적으로 작동하는 동안에는 청색으로 켜집 니다.
하드 디스크 드라이브 표시등 패턴 그림 4 . 하드 디스크 드라이브 표시등 1. 하드 디스크 드라이브 작동 표시등(녹색) 2. 하드 디스크 드라이브 상태 표시등(녹색 및 황색) 3. 하드 디스크 드라이브 하드 디스크 드라이브 상태 표시등 패턴(RAID에만 해당) 상태 녹색으로 초당 2번 깜박임 하드 디스크 드라이브의 식별 또는 분리를 준비함 꺼짐 하드 디스크 드라이브가 장착 또는 분리 준비 됨 노트: 하드 디스크 드라이브 상태 표시등은 모든 하드 디스크 드라이브가 시스템 전원을 켠 후 초기화될 때까지 꺼진 상태로 있습니다. 이 기간동안 하드 디스크 드라이브를 삽입하거나 분리할 수 없습니다. Dell PowerEdge RAID 컨트롤러 PERC H830 및 12Gb SAS HBA는 모든 하드 디스크 드라이 브를 검색하고 초기화하는데 최대 1분이 걸릴 수 있습니다.
후면 패널 기능 및 표시등 그림 5 . 후면 패널 기능 및 표시등 항목 표시등, 단추 또는 커넥터 설명 1 전원 공급 장치 또는 냉각 팬 모듈(PS1) 600 W 전원 공급 장치. 자세한 내용은 전원 표시등 코드목록을 참조하십시오. 2 기본 인클로저 관리 모듈(EMM 0) EMM는 다음을 제공합니다: ● 인클로저 및 호스트 서버 간의 데이터 경로. 3 보조 EMM(EMM 1) ● 사용자 인클로저용 인클로저 관리 기능. 4 정보 태그 서비스 태그를 기록할 수 있는 슬라이드형 레이블 패널. 5 전원 스위치(2개) 전원 스위치는 인클로저에 대한 전원 공급 장치 출력을 제어합니다. 6 전원 공급 장치 또는 냉각 팬 모듈(PS 2) 600 W 전원 공급 장치. 자세한 내용은 전원 표시등 코드목록을 참조하십시오. 인클로저 관리 모듈 각 EMM은 인클로저에 다음과 같은 데이터 경로 및 인클로저 관리 기능을 제공합니다.
항목 표시등, 단추 또는 커 넥터 아이콘 설명 1, 2, 3, 4 SAS 포트(매입 또는 매출) 호스트 또는 상향 체인 확장 인클로저에 데이지 체인 방식으로 다음 하향 체인 확 장 인클로저의 배선을 위한 SAS 연결을 제공합니다.(단일 포트, 이중 및 다중 체 인 구성) 5 USB Mini-B(직렬 디버 그 포트) 공학적 용도 전용. 6 7-세그먼트 디스플레 이 SAS 체인에 있는 인클로저의 위치를 표시합니다. 두 EMM이 설치될 경우 인클로저의 장애 극복 두 EMM이 설치될 경우 일정한 정도의 장애 극복이 제공됩니다. EMM에 오류가 생겼을 경우에 인클로저 요소의 제어 및 모니터링은 한 EMM에서 다른 EMM으로 전송 가능 합니다. EMM 및 동등 EMM 사이의 네트워크 통신이 종료될 때마다 장애 극복이 발생합니다. 동등 EMM에 오류가 발생하는 경우, 나머지 EMM은 오류가 발생한 EMM의 황색 상태 LED를 활성화합니다.
항목 LED 아이콘 색상 상태 ● 처음 전원 공급 장치 모듈의 전원을 켜면 짧게 점멸됩니다. 3 AC 전원 녹색 ● 켜짐 - 전원 스위치가 켜져 있는지 여부에 관계없이 전원 공급 장치 모듈이 AC 전원에 연결되어 있습니다. ● 꺼짐 - 전원 공급 장치 모듈이 AC 전원에서 완전히 분리된 상태입 니다. 기타 필요한 정보 경고: 시스템과 함께 제공되는 안전 및 규정 정보를 참조하십시오. 보증 정보는 이 문서 안에 포함되어 있거나 별도의 문서로 제 공될 수 있습니다. ● 랙 솔루션과 함께 제공되는 랙 설명서에는 시스템을 랙에 설치하는 방법이 기술되어 있습니다. ● 시작 안내서는 시스템 기능, 시스템 설정 및 기술 사양에 대한 개요를 제공합니다. ● OpenManage Server Administrator 설명서는 Server Administrator의 저장 장치 관리 서비스를 사용하여 저장 장치 솔루션을 관리하 는 데 대한 정보를 제공합니다.
2 인클로저 구성요소 설치 주제: • • • • • • • • 권장 도구 전면 베젤(선택 사양) 하드 디스크 드라이브 인클로저 관리 모듈 AC 전원 공급 장치 또는 냉각 팬 모듈 DC 전원 공급 장치에 대한 정보 제어판 후면판 권장 도구 이 항목의 절차를 수행하려면 다음 품목이 필요할 수 있습니다. ● 시스템 키 잠금 장치의 키 ● #2 십자 드라이버 ● 손목 접지대 전면 베젤(선택 사양) 전면 베젤 분리 1. 2. 3. 4. 시스템 키를 사용하여 전면 베젤을 잠금 해제합니다(잠긴 경우). 키 잠금 장치 옆에 있는 분리 래치를 들어 올립니다. 베젤의 왼쪽 끝을 전면 패널 반대 방향으로 당깁니다. 베젤의 오른쪽 끝에 있는 고리를 풀고 베젤을 당겨 시스템에서 꺼냅니다.
그림 8 . 전면 베젤 분리 및 설치 1. 키 잠금 장치 2. 전면 베젤 전면 베젤 설치 1. 베젤의 오른쪽 끝을 섀시에 겁니다. 2. 베젤의 움직일 수 있는 다른 끝을 시스템에 맞춥니다. 3. 키 잠금 장치를 사용하여 베젤을 고정합니다. 하드 디스크 드라이브 안전: 모델 AMT, E03J, 및 E04J 모델 AMT, E03J, 및 E04J는 IEC 60950-1:2005의 1.2.7.3 조에 정의된 것과 같이 접근이 제한된 위치에서 설치하기 위한 것입니다. 구성을 기준으로, 인클로저는 내장형 드라이브 베이에서 최대 최대 12개의 3.5인치 SAS 하드 디스크 드라이브를 내부 드라이브 베이 에서 지원 합니다. 하드 디스크 드라이브는 하드 디스크 드라이브 캐리어를 통해 후면판에 연결되며 핫 스왑 가능하도록 구성할 수 있 습니다. 주의: 드라이브 포맷 중에 인클로저를 종료하거나 다시 부팅하지 마십시오. 하드 디스크 드라이브 포맷중에 종료하거나 부팅하 면 하드 디스크 드라이브에 오류가 발생할 수 있습니다.
그림 9 . 3.5인치 하드 드라이브 보호물 분리 및 설치 1. 하드 디스크 드라이브 보호물 2. 분리 탭 하드 디스크 드라이브 보호물 설치 1. 설치되어 있는 경우 전면 베젤을 분리합니다. 전면 베젤 분리를 참조하십시오. 2. 하드 드라이브 보호물이 완전히 장착될 때까지 드라이브 베이에 밀어넣습니다. 3. 핸들을 닫아 보호물을 제자리에 잠급니다. 4. 해당하는 경우 전면 베젤을 설치합니다. 전면 베젤 설치를 참조하십시오. 하드 디스크 드라이브 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 전면 베젤이 설치되어 있는 경우 전면 베젤을 분리합니다.
그림 10 . 하드 디스크 드라이브 분리 및 설치 a. 분리 단추 b. 하드 디스크 드라이브 c. 하드 디스크 드라이브 캐리어 핸들 하드 디스크 드라이브 장착 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: SAS 후면판에서 사용할 수 있도록 검사 및 승인된 하드 디스크 드라이브만 사용하십시오. 주의: 하드 디스크 드라이브를 설치할 때 인접 하드 디스크 드라이브가 완전히 설치되어 있는지 확인합니다.
그림 11 . 3.5인치 하드 디스크 드라이브 캐리어에 하드 드라이브 분리 및 설치 1. 나사(4개) 2. 하드 디스크 드라이브 3. 하드 디스크 드라이브 캐리어 하드 디스크 드라이브를 하드 디스크 드라이브 캐리어에 설치 1. 하드 디스크 드라이브 커넥터 끝이 후면에 놓이도록 하드 디스크 드라이브를 하드 디스크 드라이브 캐리어에 밀어 넣습니다. 2. 하드 디스크 드라이브의 나사 구멍을 하드 디스크 드라이브 캐리어 후면의 구멍에 맞춥니다. 올바르게 맞춰지면 하드 디스크 드라이브 후면이 하드 디스크 드라이브 캐리어 후면과 접하게 됩니다. 3. 나사 4개를 장착하고 조여서 하드 디스크 드라이브를 하드 디스크 드라이브 캐리어 후면에 고정합니다. 인클로저 관리 모듈 중복 인클로저 관리를 사용하는 인클로저에는 두 개의 인클로저 관리 모듈(EMM)이 탑재 되어 있습니다. 인클로저를 단일 포트, 이중 모드 또는 다중 모드로 구성 할 수 있습니다.
그림 12 . EMM 보호물 분리 및 설치 1. EMM 보호물 2. 분리 래치 EMM 보호물 설치 EMM 보호물을 설치하려면, 보호물과 EMM 베이를 맞추고 딸깍하는 소리가 날 때까지 보호물를 섀시에 삽입하십시오. EMM 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. EMM에 연결된 SAS 케이블을 분리합니다. 2. 분리 탭을 아래로 누르고 분리 레버를 섀시에서 당깁니다. 3. 분리 레버를 잡고 모듈을 섀시에서 잡아 당깁니다. 노트: EMM을 겹쳐서 올려 놓으면 민감한 EMI 접촉부가 손상됩니다.
그림 13 . EMM 분리 및 설치 1. 분리 레버 2. EMM 3. 분리 탭 EMM 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 2. 3. 4. 5. EMM을 EMM 베이에 삽입하고 장착합니다. 딸깍하는 소리가 날 때까지 분리 레버를 섀시 쪽으로 밉니다. 모든 SAS케이블을 EMM에 연결합니다. 최신 펌웨어에 대한 정보는 Dell 지원 웹사이트인 dell.com/support를 참조하십시오. 해당하는 경우, EMM용 펌웨어를 업데이트합니다. 노트: 인클로저에 EMM이 2개가 설치되어 있는 경우, 반드시 EMM에 설치된 펌웨어 버전이 동일한지 확인해야 합니다.
AC 전원 공급 장치 또는 냉각 팬 모듈 분리 노트: 정상적으로 작동하는 전원 공급 장치 또는 냉각 팬 모듈을 분리하는 경우 충분한 냉각을 제공하기 위해 나머지 모듈의 팬 속도가 현저히 빨라집니다. 새 전원 공급 장치 또는 냉각 팬 모듈이 설치되면 팬 속도가 서서히 느려집니다. 1. 전원 공급 장치 또는 냉각 팬 모듈의 전원을 끕니다. 2. 전원 케이블을 전원에서 분리합니다. 3. 전원 케이블을 고정하는 당김 안전 끈을 제거한 다음 전원 케이블을 전원 공급 장치 또는 냉각 팬 모듈에서 분리합니다. 경고: 전원 공급 장치 또는 냉각 팬 모듈은 무겁습니다. 모듈을 분리하는 동안 양손을 사용하십시오. 4. 분리 탭을 누르고 섀시에서 전원 공급 장치를 당겨 빼냅니다. 그림 14 . 전원 공급 장치 또는 냉각 팬 모듈 분리 및 설치 1. 분리 탭 2. 전원 공급 장치 3. EMM 또는 전원 공급 장치 케이지 AC 전원 공급 장치 또는 냉각 팬 모듈 설치 1.
그림 15 . 전원 케이블 고정 a. 당김 안전 끈 주의: 전원 케이블을 연결할 때는 당김 안전 끈으로 케이블을 고정합니다. 노트: 인클로저의 전원이 켜져 있는 경우, AC 전원 케이블이 전원 공급 장치/냉각 팬 모듈에 연결되고 전원 스위치가 켜질 때 까지 모든 전원 공급 장치 LED가 꺼져있습니다. 4. 전원 공급 장치/냉각 팬 모듈의 전원을 켭니다. DC 전원 공급 장치에 대한 정보 MD 시리즈 저장소 어레이는 두 개의 전원 공급 장치 모듈로부터 전원을 받습니다. DC 전원 MD 시리즈 저장소 어레이에서 전원 공급 장치 모듈은 두 개의 48V DC 전원 공급 장치로부터 전원을 받습니다. 각 전원 공급 장치 모듈에 두 개의 냉각 팬이 있습니다. 노트: 어레이의 냉각을 유지하는 팬이 전원 공급 장치 모듈에 통합되어 있으며, 별도로 교체할 수 없습니다. 팬에 오류가 발생한 경우 전체 전원 공급 장치 모듈을 교체해야 합니다.
항목 LED 색상 상태 1 전원 출력 녹색 ● 켜짐 - 정상 작동 상태입니다. 전원 공급 장치가 DC 전원에 연결되어 있고 전원 스위치가 켜져 있습니다. 전원 공급 장치 모듈이 어레이에 DC 전원을 공급합니다. ● 꺼짐 - 다음 중 하나를 나타냅니다. ○ 전원 스위치가 꺼져 있습니다. ○ 전원 공급 장치 모듈이 전원에 연결되어 있지 않습니다. ○ 오류 상태가 발생했습니다. 2 전원 공급 장 치 모듈 오류 노란색 ● 켜짐 - 오류가 감지되어습니다. ● 꺼짐 - 양호한 상태입니다. ● 처음 전원 공급 장치 모듈의 전원을 켜면 짧게 점멸됩니다. 3 라인 입력 녹색 ● 켜짐 - 전원 스위치가 켜져 있는지 여부에 관계없이 전원 공급 장치 모듈이 DC 전원에 연 결되어 있습니다. ● 꺼짐 - 전원 공급 장치 모듈이 DC 전원에서 완전히 분리된 상태입니다. DC 전원 공급 장치 모듈 후면 패널 기능 그림 17 .
키트 내용물 ● Molex # 394260002(PSU 쪽) ● Molex # 39422-0012 메이팅 DC 전원 커넥터 필요한 도구 ● 핸드 크림핑 도구(Tyco Electronics, 58433-3 또는 이와 동등). ● 10 AWG 크기의 단선 또는 연선 절연 구리선으로부터 절연체를 제거할 수 있는 와이어 스트리퍼 플라이어 노트: 알파 와이어 부품 번호 3080 또는 이에 상당하는 선(65/30 연선)을 사용합니다. 필요한 와이어 ● UL 10 AWG, 최대 2m(연선) 검정색 와이어 1개 [–(48–60)V DC] ● UL 10 AWG, 최대 2m(연선) 빨간색 와이어 1개 (V DC 리턴) ● UL 10 AWG, 최대 2m(연선) 녹색/노란색/노란색 줄이 있는 녹색 와이어(안전 접지) 안전 접지 와이어 조립 및 연결 노트: -48 ~ 60V DC 전원 공급 장치를 사용하는 장비의 경우 자격 있는 전기 기사가 DC 전원 및 안전 접지에 대한 모든 연결을 수 행해야 합니다.
전원 케이블 배선 노트: -48 ~ 60V DC 전원 공급 장치를 사용하는 장비의 경우 자격 있는 전기 기사가 DC 전원 및 안전 접지에 대한 모든 연결을 수 행해야 합니다. 직접 DC 전원에 연결하거나 접지를 설치하도록 시도하지 마십시오. 모든 전기 배선은 해당 지역 또는 국가 코드 와 규칙을 준수해야 합니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함 께 제공된 안전 지침을 읽고 따르십시오. DC 전원 공급 장치 모듈은 자격이 있는 전기 기사가 사용자의 환경에서 DC 전원에 고정 배선으로 연결해야 합니다. DC 전원에 DC 전 원 공급 장치 모듈을 배선하려면 다음을 수행합니다. 1. 전원 스위치가 꺼짐(OFF) 상태인지 확인하고 전원 공급 장치 모듈이 꺼져 있는지 확인합니다. 2. 적절한 DC 전원에 열려 있는 단자(비피복 와이어 끝)를 연결합니다. 다음 표에 지정된 대로 수행합니다.
그림 20 . DC 전원 케이블 연결 a. 부착된(걸려 있는) 핑거 나사 b. 전원 공급 장치 케이블의 커넥터 c. 전원 공급 장치 모듈의 커넥터 DC 전원 공급 장치 분리 경고: -48 ~ 60V DC 전원 공급 장치를 사용하는 장비의 경우 자격 있는 전기 기사가 DC 전원 및 안전 접지에 대한 모든 연결을 수행해야 합니다. 직접 DC 전원에 연결하거나 접지를 설치하도록 시도하지 마십시오. 모든 전기 배선은 해당 지역 또는 국가 코 드와 규칙을 준수해야 합니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 시스템이 정상적으로 작동하려면 하나의 전원 공급 장치가 필요합니다. 중복 시스템의 경우에는 시스템이 켜져 있을 때 전 원 공급 장치를 한 번에 하나만 분리하고 교체합니다. 노트: 케이블 관리대(선택 사양)가 전원 공급 장치 분리를 방해하는 경우에는 관리대의 래치를 벗기고 들어 내야 합니다.
그림 21 . DC 전원 공급 장치 모듈 분리 및 설치 a. 분리 래치 b. 전원 공급 장치 모듈 c. 전원 공급 장치 모듈 핸들 DC 전원 공급 장치 모듈 설치 노트: -48 ~ 60V DC 전원 공급 장치를 사용하는 장비의 경우 자격 있는 전기 기사가 DC 전원 및 안전 접지에 대한 모든 연결을 수 행해야 합니다. 직접 DC 전원에 연결하거나 접지를 설치하도록 시도하지 마십시오. 모든 전기 배선은 해당 지역 또는 국가 코드 와 규칙을 준수해야 합니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함 께 제공된 안전 지침을 읽고 따르십시오. 1. 두 전원 공급 장치 모듈의 유형과 최대 출력 전력이 동일한지 확인합니다. 노트: 최대 출력 전력(와트 단위)은 전원 공급 장치 모듈 레이블에 표시되어 있습니다. 2. 분리 래치가 제자리에 장착되어 전원 공급 장치 모듈이 완전히 고정될 때까지 새 전원 공급 장치 모듈을 섀시에 밀어 넣습니다.
전원 공급 장치 모듈 오류 다음 항목의 일부 또는 전체에 따라 전원 공급 장치 모듈 오류를 식별할 수 있습니다. ● 전원 공급 장치 모듈의 LED ● 콘솔, 이벤트 로그 또는 모듈러 디스크 저장소 관리자의 메시지 노트: 어레이의 후면을 볼 때 전원 공급 장치 모듈 0이 왼쪽에 있고, 전원 공급 장치 모듈 1이 오른쪽에 있습니다. DC 전원 공급 장치 문제 해결 경고: -48 ~ 60V DC 전원 공급 장치를 사용하는 장비의 경우 자격 있는 전기 기사가 DC 전원 및 안전 접지에 대한 모든 연결을 수행해야 합니다. 직접 DC 전원에 연결하거나 접지를 설치하도록 시도하지 마십시오. 모든 전기 배선은 해당 지역 또는 국가 코 드와 규칙을 준수해야 합니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 시스템이 정상적으로 작동하려면 하나의 전원 공급 장치가 필요합니다.
전원 와트 700W 열 손실 2388 BTU/hr(중복, 700 W 전원 공급 장치) 노트: 열 손실은 전원 공급 장치 와트 정격을 사용 하여 계산합니다. 전압 –48 ~ –60V DC 온도 최대 작동 주위 온도 35° C 지원되는 작동 온도 확장 범위 및 구성에 대한 자세한 내용은 dell.com/support/manuals를 참조하십시오. 제어판 제어판 분리 1. 인클로저 및 호스트 서버의 전원을 끕니다. 2. 인클로저에 연결된 모든 전원 케이블을 분리합니다. 3. 슬롯 0 ~ 2의 하드 디스크 드라이브를 분리합니다. 하드 디스크 드라이브 분리 페이지 13 참조. 4. 분리 탭을 인클로저 전면 쪽으로 밀어낸 후에 섀시에서 제어판을 밀어 꺼냅니다. 그림 22 . 제어판 분리 및 설치 a. 제어판 b. 섀시 c. 분리 탭 제어판 설치 1. 제어판을 인클로저 슬롯에 맞춥니다. 2. 제어판을 분리 탭이 제자리에 맞물릴 때까지 인클로저로 밀어 넣습니다.
3. 하드 디스크 드라이브를 각각의 해당 슬롯에 장착합니다. 하드 디스크 드라이브 설치를 참조하십시오. 4. 전원 케이블을 모두 인클로저에 연결합니다. 5. 인클로저 및 호스트 서버의 전원을 켭니다. 후면판 경고: 시스템을 들어 올려야 할 경우에는 다른 사람의 도움을 받으십시오. 부상을 피하려면 혼자 힘으로 시스템을 들어 올리지 마십시오. 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 후면판 분리 1. 인클로저의 전원을 끄고, 전원 콘센트에서 인클로저를 분리하십시오. 2. 인클로저에 연결된 모든 전원 케이블을 분리합니다. 3. 하드 디스크 드라이브를 분리합니다.
그림 24 . 후면판 분리 및 설치 a. 나사(5개) b. 조임 나사(2개) c. 후면판 후면판 설치 1. 후면판의 구멍을 인클로저의 구멍과 맞춥니다. 2. 조임 나사를 조여 후면판을 섀시에 고정합니다. 3. 후면판을 섀시에 고정하는 나사를 장착합니다. 4. EMM/전원 공급 장치 케이지의 슬롯을 섀시의 탭에 맞춥니다. 5. EMM/전원 공급 장치 케이지를 인클로저 전면 쪽으로 밉니다. 6. EMM/전원 공급 장치 케이지를 섀시에 고정하는 나사를 장착합니다. 7. 제어판을 설치합니다. 제어판 설치를 참조하십시오. 8. 전원 공급 장치 또는 냉각 팬 모듈을 설치합니다. AC 전원 공급 장치 또는 냉각 팬 모듈 설치를 참조하십시오. 9. 하드 디스크 드라이브를 설치합니다. 하드 디스크 드라이브 설치를 참조하십시오. 10. 전원 케이블을 모두 인클로저에 연결합니다. 11. 인클로저 및 호스트 서버의 전원을 켭니다.
3 인클로저 문제 해결 주제: • • • • • • • • • • • 안전 제일 — 사용자 및 인클로저를 위함 인클로저 스타트 업 오류 문제 해결 통신 단절 문제 해결 외부 연결 문제 해결 전원 공급 장치 또는 냉각 팬 모듈의 문제 해결 인클로저의 냉각 문제 해결 인클로저 관리 모듈 문제 해결 하드 디스크 드라이브 문제 해결 인클로저 연결 문제 해결 습식 인클로저 문제 해결 손상된 인클로저 문제 해결 안전 제일 — 사용자 및 인클로저를 위함 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오.
주의: 데이터 손실을 방지하기 위해 인클로저를 끄기 전에 호스트 서버를 끄는 것이 좋습니다. 1. 오류가 있는 PSU를 찾아서 LED 상태를 확인합니다. ● AC 전원 LED가 켜지지 않은 경우, 전원 공급 장치가 연결된 전원 코드 및 전원을 확인합니다. ○ 다른 장치를 전원에 연결하여 정상적으로 작동되는지 확인합니다. ○ 케이블을 다른 전원에 연결합니다. ○ 전원 케이블을 교체합니다. 문제가 해결되지 않으면 도움말 얻기를 참조하십시오. ● DC 전원 LED가 켜지지 않는 경우, 전원 스위치가 켜져 있는지 확인합니다. 전원 스위치가 켜져 있으면 2단계를 참조하십시오. ● PSU의 오류 표시등이 켜져 있으면 도움말 얻기를 참조하십시오. 주의: 전원 공급 장치 모듈은 핫 스왑이 가능합니다. 인클로저가 단일 전원 공급 장치 모듈에서 작동할 수 있지만, 제대로 냉 각되도록 하려면 두 모듈이 모두 설치되어 있어야 합니다.
○ ○ ○ ○ 저장 장치 인클로저 및 서버에 케이블을 재장착하십시오. 저장 장치 인클로저를 재시작하고 인클로저가 완전하게 부팅될 때까지 기다리십시오. 서버의 전원을 켭니다. 링크 상태 LED를 확인합니다. 링크 상태 LED가 녹색이 아닌 경우, 다음 단계를 계속하십시오. 문제가 해결되지 않으면 도움말 얻기를 참조하십시오. 하드 디스크 드라이브 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 하드 디스크 드라이브를 인클로저에서 분리합니다. 하드 디스크 드라이브 제거를 참조하십시오.
● 후면판 3. 최소한 하루 이상 시스템을 건조시킵니다. 4. 2단계에서 분리한 구성부품을 다시 설치합니다. 5. 모든 케이블을 연결하고 인클로저의 전원을 켭니다. 인클로저가 제대로 시작되지 않으면 도움말 얻기를 참조하십시오. 손상된 인클로저 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처리할 수 있습니다. Dell의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 다음 구성부품이 올바르게 설치되어 있는지 확인합니다. ● 하드 디스크 드라이브 ● EMM ● 전원 공급 장치 또는 냉각 팬 모듈 ● 제어판 ● 후면판 2. 모든 케이블이 올바르게 연결되고 커넥터에 손상된 핀이 없는지 확인합니다. 3.
4 도움말 얻기 주제: • • Dell에 문의하기 설명서에 대한 사용자 의견 Dell에 문의하기 Dell은 다양한 온라인 및 전화 기반 지원과 서비스 옵션을 제공합니다. 인터넷에 연결되어 있지 않은 경우 구매 송장, 포장 명세서, 청 구서 또는 Dell 제품 카탈로그에서 연락처 정보를 확인할 수 있습니다. 가용성은 국가 및 제품에 따라 다르며, 해당 지역에서 일부 서비 스를 이용하지 못할 수도 있습니다. 1. Dell.com/support로 이동합니다. 2. 페이지 하단 오른쪽 코터의 드롭다운 메뉴에서 국가를 선택합니다. 3. 맞춤화된 지원: a. 서비스 태그 입력 필드에 시스템 서비스 태그를 입력합니다. b. Submit(제출)을 클릭합니다. 여러 가지 지원 범주가 나열되어 있는 지원 페이지가 표시됩니다. 4. 일반 지원: a. 제품 범주를 선택합니다. b. 제품 세그먼트를 선택합니다. c. 제품을 선택합니다. 여러 가지 지원 범주가 나열되어 있는 지원 페이지가 표시됩니다.