Dell U2717DA ユーザーガイド モデル番号: U2717DA 規制モデル:U2717Dt
注意:注意は、 コンピューターのより良い使用を助けるための重要な情報を示します。 警告:警告は、 もし指示に従わない場合は、ハードウェアに対する損傷またはデータ損失が 起こりうることを示します。 危険:危険は器物損壊、怪我、死亡に繋がる可能性を示します。 Copyright © 2016 Dell Inc. All rights reserved. 本製品は米国および国際的な著作権法および知的財 産法で保護されています。 Dell™およびDellのロゴは、米国および/またはその他の地域におけるDell Inc.の商標です。ここに記載さ れているその他のマークおよび名称は、各社の商標である場合があります。 2016 – 01 Rev.
内容 お使いのモニターについて . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 パッケージの内容 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 機能 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 部品とコントロール. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 仕様 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 プラグアンドプレイ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 LCDモニター品質とピクセルポリシー . . .
ビルトイン診断 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 共通の問題 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 製品固有の問題 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 モバイル高品位リンク (MHL)に特有の問題 . . . . . . . . . . . . . . . . . . 58 付録 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 安全上の注意. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 FCC通知(米国のみ)およびその他規制情報. .
お使いのモニターについて パッケージの内容 モニターは下記で示されるコンポーネントが同梱されています。すべてのコンポーネントが含 まれていることを確認し、何か足りない場合にはDellにご連絡ください。 注意:一部の品目はオプションで、モニターには同梱されていないことがあります。ご使用 の国によっては、一部の機能またはメディアが利用できないことがあります。 モニター アームライザー アームベース 六角レンチ お使いのモニターについて | 5
電源ケーブル(国によって異なります) USB 3.0アップストリームケーブル (モ ニターのUSBポートを有効にします) DPケーブル(ミニDP対DP) • ドライバーと説明書メディア • 簡単セットアップガイド • 安全規制情報 • 出荷時較正レポート 機能 Dell U2717DAフラットパネルディスプレイは、 アクティブマトリクス、薄膜トランジスター(TFT) 、液晶ディスプレイ (LCD) 、LEDバックライトを有します。モニターの特徴は次のとおりです。 • 68.
• BFR/PVCを含まないモニター(ケーブルを除く)。 • ヒ素を含まないガラスと水銀を含まないパネル(のみ)。 • エネルギーゲージには、モニターが消費しているエネルギーレベルがリアルタイムで表 示されます。 • スリープモード時には0.
背面ビュー ラベル 説明 目的 1 100 mm x 100 mmのVESA取り付 VESA互換壁取り付けキット(100 mm x 100 け穴(VESAカバーの下) mm)を使用する壁取り付けモニター。 2 規制ラベル 規制承認をリストします。 3 アームリリースボタン アームをモニターからリリースします。 4 セキュリティロックスロット モニターを固定するために、セキュリティロッ クを使用します(別売)。 5 バーコード、 シリアル番号、サービ スタグラベル 技術サポートを受けるためにDellに連絡する 際に、 このラベルを参照します。 6 アームカバー ケーブル管理コンパートメントにアクセスす るには、 カバーを取り外してください。 7 ケーブル管理コンパートメント コンパートメントを通して配線することで、ケ ーブルを管理するために使用します。ケーブ ル管理を参照してください。 側面ビュー USBダウンストリームポート バッテリーアイコンが「 ポートは BC 1.
底面ビュー ラベル 説明 目的 1 AC電源コードコネクタ 電源ケーブルを接続してください 。 2 HDMI(MHL)ポート HDMIケーブルを使用してコンピューターに接続、 またはMHLケーブル(オプション)を使用してMHL デバイスに接続します。 3 DPコネクタ (イン) コンピューターの DP ケーブルを接続してくださ い。 4 mDPコネクタ (イン) コンピュータをmDP-DPケーブルに接続します。 5 DPコネクタ (アウト) MST (マルチストリームトランスポート)対応モニタ 用のDP出力。DP 1.
仕様 パネル スクリーンタイプ アクティブマトリクス - TFT LCD パネルタイプ IPS方式 表示可能画像 対角 68.47cm(27インチ) アクティブ領域 水平 569.736mm(22.43インチ) 垂直 335.664mm(13.21インチ) 191239.86mm2(296.30インチ2) 領域 ピクセルピッチ 0.2331 mm x 0.
プリセットディスプレイモード ディスプレイモード 水平周波数 (kHz) 垂直周波数 (Hz) ピクセルクロック 同期極性 (MHz) (水平/垂直) 720 x 400 31.5 70.0 28.3 -/+ 640 x 480 31.5 60.0 25.2 -/- 640 x 480 37.5 75.0 31.5 -/- 800 x 600 37.9 60.3 40.0 +/+ 800 x 600 46.9 75.0 49.5 +/+ 1024 x 768 48.4 60.0 65.0 -/- 1024 x 768 60.0 75.0 78.8 +/+ 1152 x 864 67.5 75.0 108.0 +/+ 1280 x 1024 64.0 60.0 108.0 +/+ 1280 x 1024 80.0 75.0 135.0 +/+ 1600 x 1200 75.0 60.0 162.0 +/+ 1920 x 1080 67.5 60.0 148.
MSTマルチストリーム転送 (MST) モード MSTソース監視 対応している外部モニター最大数 2560 x 1440/60 Hz 2560 x 1440/60 Hz 2 注意:サポーされる最大外部モニター解像度は 2560 x 1440 60Hz のみです。 電気的仕様 ビデオ入力信号 • それぞれの微分直線に対するジタルビデオ信号。 100オームインピーダンスでの微分直線ごとに。 • DP/HDMI/MHL信号入力サポート 入力電圧/周波数/電流 100 VAC〜240 VAC / 50 Hzまたは60 Hz ± 3 Hz / 1.7 A(最 大) 突入電流 120 V: 40 A(最大) 240 V: 80 A(最大) 物理特性 コネクタータイプ • DP コネクター (include DP in and DP out) • mDP コネクター • HDMI/MHL コネクター • オーディオラインアウト • USB 3.0アップストリームポートコネクター。 • USB 3.
アームの寸法 高さ (拡張) 441.6mm(17.39インチ) 幅 121.6mm(4.79インチ) 奥行き 384.3mm(15.13インチ) 重量 パッケージ含む 9.7kg(21.38ポンド) アームアセンブリとケーブ 7.1kg(15.65ポンド) ルを含む重量 アームアセンブリを含ま ない重量 (壁取り付けまたはVESA マウント用) 4.5kg(9.92ポンド) アームアセンブリの重量 2.3kg(5.07ポンド) 環境特性 温度 動作 0° C to 40° C (32° F to 104° F) 非動作 –20° C to 60° C (–4° F to 140° F) 湿度 動作 10%から80%(結露なし) 非動作 5%から90%(結露なし) 高度 動作 非動作 熱出力 最高5,000m(16,404フィート) 最高12,192m(4万フィート) 252.5 BTU/時(最大) 88.
電源管理モード お使いのコンピューターにVESAのDPM準拠ディスプレイカードまたはソフトウェアがインスト ールされている場合、モニターが使用中でないときには、 自動的に消費電力を低減します。こ れは電源セーブモードです*。コンピューターがキーボード、マウス、その他の入力デバイスか らの入力を検出すると、モニターは自動的に機能を再開します。次の表は消費電力と省電力モ ードの信号を示しています。 VESAモード 水平同期 垂直同期 ビデオ 通常動作 アクティブ アクティブ アクティブ 白 アクティブオフ 無効 モード 無効 オフ 白(ゆっくりと 0.5W未満 点滅) スイッチオフ - - オフ - Energy Star 消費電力 オンモード 23.7 W*** 電源ランプ 消費電力 74W(最大)** 26W(通常) 0.
ピン割当 DPコネクタ (イン) ピン番号 接続された信号ケーブルの20ピン側 1 ML3(n) 2 GND 3 ML3(p) 4 ML2(n) 5 GND 6 ML2(p) 7 ML1(u) 8 GND 9 ML1(p) 10 ML0(n) 11 GND 12 ML0(p) 13 CONFIG1 14 CONFIG2 15 AUX CH (p) 16 GND 17 AUX CH (n) 18 ホットプラグ検出 19 復帰 20 DP_PWR お使いのモニターについて | 15
DPコネクタ (アウト) ピン番号 接続された信号ケーブルの20ピン側 1 ML0(p) 2 GND 3 ML0(n) 4 ML1(p) 5 GND 6 ML1(n) 7 ML2(p) 8 GND 9 ML2(n) 10 ML3(p) 11 GND 12 ML3(n) 13 CONFIG1 14 CONFIG2 15 AUX CH (p) 16 GND 17 AUX CH (n) 18 ホットプラグ検出 19 復帰 20 DP_PWR 16 | お使いのモニターについて
mDPコネクタ ピン番号 接続された信号ケーブルの20ピン側 1 GND 2 ホットプラグ検出 3 ML3 (n) 4 CONFIG1 5 ML3 (p) 6 CONFIG2 7 GND 8 GND 9 ML2 (n) 10 ML0 (p) 11 ML2 (p) 12 ML0 (p) 13 GND 14 GND 15 ML1 (n) 16 AUX (p) 17 ML1 (p) 18 AUX (n) 19 GND 20 DP_PWR お使いのモニターについて | 17
HDMIコネクタ ピン番号 接続された信号ケーブルの19ピン側 1 TMDSデータ2+ 2 TMDSデータ2シールド 3 TMDSデータ2- 4 TMDSデータ1+ 5 TMDSデータ1シールド 6 TMDSデータ1- 7 TMDSデータ0+ 8 TMDSデータ0シールド 9 TMDSデータ0- 10 TMDSクロック+ 11 TMDSクロックシールド 12 TMDSクロック- 13 CEC 14 使用不可(デバイス無接続) 15 (SCL) DDCクロック 16 (SDA) DDCデータ 17 DDC/CECグランド 18 +5V電源 19 ホットプラグ検出 18 | お使いのモニターについて
MHLコネクタ ピン番号 接続された信号ケーブルの19ピン側 1 N/C 2 CD_SENSE 3 N/C 4 N/C 5 TMDS_GND 6 N/C 7 MHL+ 8 MHL_Shield 9 MHL- 10 N/C 11 TMDS_GND 12 N/C 13 N/C 14 N/C 15 CD_PULLUP 16 N/C 17 VBUS_CBUS_GND 18 VBUS 19 CBUS 2Shell シールド お使いのモニターについて | 19
ユニバーサル・シリアルバス (USB) インターフェース このセクションでは、モニターで利用できるUSBポートについての情報を提供します。 注意:BC 1.2準拠のデバイスのUSBダウンストリームポート (バッテリーアイコンが「 」のポート) で最大2 A、その他の3つのUSBダウンストリームポートで最大0.9 A。 お使いのコンピューターには次のUSBポートがあります。 • 1xアップストリーム - 下部 • 4xダウンストリーム - 左側に2つ、下部に2つ 充電ポート - 背面カバーのポート(バッテリーアイコンが「 」のポート)は、デバイ スがBC 1.2に対応している場合、急速電流充電をサポートします。 注意:モニターのUSBポートは、モニターの電源がオンまたは省電力モードのときだけ動 作します。モニターの電源を切り、その後オンにした場合、接続された周辺機器は、通常の 動作を再開するまでに数秒かかることがあります。 転送速度 データレート 消費電力 スーパースピード 5Gbps 4.5W(最大、各ポート) ハイスピード 480Mbps 2.
プラグアンドプレイ 任意のプラグアンドプレイ互換コンピューターにモニターをインストールすることができます。 モニターは自動的にディスプレイデータチャンネル(DDC) プロトコルを使用したコンピュータ ーに、拡張ディスプレイ識別子データ (EDID)を提供し、 コンピューターは自身を構成し、モニタ ー設定を最適化します。ほとんどのモニターのインストールは自動です。希望があれば、別の 設定を選択できます。モニターの設定で、モニター設定変更についての詳細情報が必要な場 合には、モニターの操作を参照ください。 LCDモニター品質とピクセルポリシー LCDモニター製造プロセスでは、1つ以上のピクセルが不変状態で固定されてしまうことは珍 しくありません。これらは確認することは難しく、ディスプレイの品質や使いやすさには影響 しません。Dellモニター品質とピクセルポリシーについての詳細は、http://www.dell.
モニターの設定 アームの取り付け 注意:モニターが工場から出荷される際、 アームライザーとアームベースは取り外されて います。 注意:アーム取り付け手順は、モニターと共に出荷されたアームに適用されます。その他 の取り付け方法 (オプション) については、それぞれのセットアップ手順を参照してくださ い。 アームベースの取り付け 次のテーブル構成には、 アームベースを取り付け可能です: A. オープンエッジのあるテーブル B. パーティションとの間に隙間のあるテーブル C. グローメットホール付きのテーブル D. その他 A.
• アームベースアセンブリを完全にテーブルにス ライドさせます。 • つまみねじをクランプディスクが完全にテーブ ルの下側に接触するまで締め付けます。 B.
| モニターの設定 • テーブルの厚みに応じて、 アームベースブラケ ットの最上段または最下段に 2 本のねじを取り 付けます。 • クランプブラケットをかぎ穴に差し込み、ひねっ て、下にスライドさせて、所定に位置に固定しま す。 • つまみねじをクランプディスクが完全にテーブ ルの下側に接触するまで締め付けます。
C.
• つまみねじをクランプディスクが完全にテーブ ルの下側に接触するまで締め付けます。 D. その他 一部のオフィスパーティションシステムは、ケーブル管理用のスイングオープンパネルが装備 されています。そのような場合、下図に示す通り、 スイングオープンパネルがアームベース取り 付けの妨げになる恐れがあります。 A. パネルを開かないと、隙間が小さすぎてアームベースブラケットを差し込むことができま せん。 B. 隙間にアームベースブラケットを差し込む前に、パネルを開く必要があります。 C.
この問題を克服するためのアームベースの推奨取り付け手順は次の通りです: A. B. C.
アームライザーの取り付け • • • • テーブルに取り付け済のアームベースのポール にアームライザーを完全に差し込みます。 アームベースからアームライザーが誤って外れ ることを防止するため、六角レンチを使って、セ ットねじを完全に締め付けます。 モニターの背面のくぼみをアーム上部の 2 つの タブに配置します。 モニターが所定の位置にカチッとはまるまで下 に傾けます。 まとめケーブル 1. 2. 3.
• ケーブルクリップとブラケットを通して、下から 上にケーブルを通します。 ケーブルをアーム下部の開口部から引き出し て、モニターの対応するコネクタに接続してくだ さい。 1. ケーブルブラケットを完全に下に動かします。 2.
チルト、 スイベル、 ピボット、垂直・水平方向の拡張 注意:これは、このモニターと共に出荷されたアームに適用されます。その他の取り付け 方法については、それぞれのセットアップ手順を参照してください。 チルトおよび垂直方向の拡張 モニターに取り付けられたアームを使って、最も快適な視聴位置にモニターを傾けたり、上昇 させたりすることができます。 30 | モニターの設定
スイベルおよび水平方向の拡張 モニターに取り付けられたアームを使って、モニターを左右に回転したり、 アームを左右に回し たりして、モニターの視聴距離を最適化することができます。 また、モニターをたたんで、机を 広々と使うことが可能です。 ピボット モニターを回転させる前に、モニター下端がぶつからないよう、モニターを最も上に上げ、完全 に傾ける必要があります。 注意: 注意: Dellコンピュータで「ディスプレイ回転」機能(横対縦表示)を使用す るには、 このモニターに含まれていない最新のグラフィックスドラ イバが必要です。 最新のグラフィックスドライバをダウンロードし て更新するには、www.dell.
システムの「ディスプレイ回転設定」の調整 モニタを回転させた後、以下の手順でシステムの「ディスプレイの回転設定」を調整する必要 があります。 注意: Dellコンピュータ以外でモニターを使用している場合、 グラフィップ ス・ドライバのウェブサイトまたはお使いのコンピュータの製造元 ウェブサイトに進み、オペレーティング・システムの回転についての 情報を確認します。 ディスプレイの回転設定を調整するには: 1 2 3 4 5 デスクトップを右クリックして、 プロパティをクリックします。 設定タブを選択し、 アドバンストをクリックします。 ATIグラフィックスカードを使っていする場合は、回転タブを選択して、お気に 入りの回転を設定します。 nVidiaグラフィックスカードを使っている場合は、nVidiaタブをクリックして、左 カラムでNVRotateを選択し、次にお気に入りの回転を選択します。 Intel®グラフィックスカードを使っている場合は、Intelグラフィックス・タブを選 択して、 グラフィックス・プロパティをクリックし、回転タブを選択し、次にお気 に入りの回転を設定します。 注意: 32 |
モニターの接続 危険:このセクションの手順を始める前に、安全上の注意に 従って下さい。 モニターをコンピューターに接続するには: 1 コンピュータの電源を切ってください。 2 モニターとコンピューターをHDMI/mDP-DP/USBケーブルで接続します。 (回転させてケーブルに接続するため、モニターを垂直に延在して完全に傾けます。 ピボットをご覧下さい。) 3 コンピュータの電源を入れてください。 4 Monitor OSD Menuで正しい入力ソースを選択しコンピュータの電源を入れてくださ い。 注意:U2717DAのデフォルト設定では通常DP 1.2. DP 1.
DP MST(マルチストリームトランスポート)機能用のモニタを接続します 注意:はDP MST機能をサポートします。 この機能を使用するには、PCグラフィックスカー ドがMSTオプションでDP1.
モバイル高品位リンク (MHL) を使用する 注意:このモニターはMHL対応です。 注意:MHL機能を使用するには、MHL認定されたケーブルと、MHL出力に対応しているソ ースデバイスのみを使用します。 注意:MHLソースデバイスによっては、画像が表示されるまで数秒以上かかることがあり ます。 注意:接続されたMHLソースデバイスがスタンバイモードに入ると、モニターの画面が黒 くなるか、MHLソースデバイスの出力に応じて以下のメッセージを表示します。 MHL接続を有効にするには、以下の手順を実行してください。 1 お使いのモニタの電力ケーブルをAC出力に差し込んでください。 2 MHL認定ケーブルを使用して、MHLソースデバイスの(マイクロ)USBポートとモニター のHDMI/MHLポートを接続します(詳細は底面図を参照)。 3 モニターとMHLソースデバイスをオンにします。 4 OSDメニューを使用して、モニターの入力ソースをHDMI(MHL)にします(詳細につい てはオンスクリーンディスプレイ (OSD) メニューの使用を参照)。 5 モニターに画像が表示されない場合には、モバイル高品位リンク (MH
モニターアームの取り外し 警告:ディスプレイパネルを傷つけないように、清潔で平面になった柔らかい場所にモニタ ーを置きます。 注意:アーム取り付け手順は、モニターと共に出荷されたアームに適用されます。その他 の取り付け方法 (オプション) については、それぞれのセットアップ手順を参照してくださ い。 アームを取り外すには 1. アームリリースボタンを押したままにします。 2. モニターを持ち上げて、 アームから取り外し ます。 1. 六角レンチを使って、ねじを反時計回りに回し ます。 図の矢印方向にアームライザーを引っ張るこ とで、 アームベースから取り外します。 2.
• アームベースの下部の固定ねじを回して、それ を取り外します。 壁取り付け(オプション) 注意:壁取り付けキットにモニターを接続するには、M4 x 10 mmネジを使用します。 VESA互換の壁取り付けキットに付属された説明書を参照してください。 1 モニターを、柔らかい布またはクッションを敷いた安定した平らなテーブルの上に置き ます。 2 アームを取り外すには。 3 フィリップス製プラス(+) スクリュードライバーを使用して、 プラスチックカバーを固定し ている4つのネジを外します。 4 壁取-り付けキットからモニターに取り付けブラケットを取り付けます。 5 壁取り付けキットに付属する取扱説明書に従って、壁にモニターを取り付けます。 注意:UL、CSA、GSリストの壁掛けブラケット使用のみ、最小負荷重量 4.5 kg(9.
モニターの操作 モニターの電源を入れる ボタンを押してモニターをオンにする 。 フロントパネルコントロールの使用 表示されている画像の特性を調整するには、モニターの前面にあるコントロールボタンを使用 します。 これらのボタンを使用してコントロールを調整するとき、OSDには変更される特性の数 値が表示されます。 38 | モニターの操作
次の表は、前面パネルのボタンを説明しています。 フロント-パネルボタン 説明 1 このボタンを使用して、 プリセットカラーモードの一覧か ら選択することができます。 ショートカットキー: プリセットモード このボタンを使って、入力ソースのリストから選択しま す。 2 ショートカットキー: 入力信号 このボタンを使用して、オンスクリーンディスプレイ (OSD)を起動し、OSDでオプションを選択します。 メニューシステムにアクセスを参照ください。 3 メニュー このボタンを使用して、 メインメニューに戻ったり、OSD メインメニューを終了します。 4 終了 5 電源(電源ライトインジケータ 付き) 電源ボタンを使用して、モニターをオンにしたりオフ にしたりします。 白い LED は、モニターの電源が入り、完全に機能す ることを示しています。 白く光るLEDは、DPMS省電力モードを示していま す。 モニターの操作 | 39
フロント-パネルボタン 画像の設定を調整するには、モニターの前面にあるボタンを使用します。 フロント-パネルボタン 説明 上(増加) と下(減少)キーを使用して、OSDメニューの項目を調整 します。 1 上 下 選択を確定するにはOKキーを使用します。 2 OK 前のメニューに戻るには、戻るキーを使用します。 3 戻る 40 | モニターの操作
オンスクリーンディスプレイ (OSD) メニューの使用 メニューシステムにアクセス 注意:別のOSDメニューに移動、OSDメニューを終了、 またはOSDメニューが消えるのを 待つと、OSDメニューを使用して行った任意の変更は、 自動的に保存されます。 1 OSDメニューを起動し、 メインメニューを表示するには、 ボタンを押します。 と ボタンを押して、オプション間を移動します。別のアイコンに移動すると、オプ ション名がハイライトされます。 3 または または ボタンを1回押して、ハイライトしたオプションをアクティブに します。 4 希望のパラメーターを選択するには と ボタンを押します。 5 ボタンを押してサイドバーに入り、 メニューの表示ランプに応じて、 または ボ タンを使用して変更します。 6 を選択して前のメニューに戻るか、 で承認してから、前のメニューに戻ります。 2 モニターの操作 | 41
アイコ メニューとサブ 説明 ン メニュー Brightness/ このメニューを使用して、輝度/コントラスト調整をアクティブにし Contrast(輝度/ ます。 コントラスト) Brightness( 輝度) 輝度はバックライトの明るさを調整します(最小0、最大100)。 ボタンを押して、輝度を上げます。 ボタンを押して、輝度を下げます。 注意:ダイナミックコントラストがオンになると、輝度の手動調整 が無効になります。 コント Contrast(コン 輝度を最初に調整し、次にさらに調整が必要な場合にのみ、 トラスト) ラストを調整します。 ボタンを押してコントラストを増加させ、 ボタンを押してコ ントラストを下げます(0から100まで)。 コントラストはモニターの明るい部分と暗い部分との明暗の差を 調整します。 42 | モニターの操作
アイコ メニューとサブ 説明 ン メニュー Input Source( 入力ソース) モニターに接続された異なるビデオ入力を選択するには、入力ソ ースメニューを使用します。 DP DPコネクターを使用している場合は、DP(DisplayPort)入力を選 択します。 を押して、DP入力ソー スを選択します。 mDP mDPコネクターを使用している場合は、mDP(Mini DisplayPort) 入力を選択します。 を押して、mDP入力ソー スを選択します。 HDMI/MHL HDMI/MHL コネクターを使用している場合は、HDMI入力を選択 します。 を押して、HDMI/MHL 入力ソー スを選択します。 自動選択 自動選択を選択するには を使用します。モニターが使用可能 な入力ソースをスキャンします。 Reset Input Source(入力 信号のリセッ ト) モニターの入力ソースを工場出荷時のデフォルトにリセットしま す。 モニターの操作 | 43
アイコ メニューとサブ 説明 ン メニュー Color(色) 色設定モードを調整するには[カラー]メニューを使用します。 Preset Mode( プリセットモードを選択すると、 スタンダード、マルチメディア、映 プリセットモ 画、 ゲーム、ペーパー、色温度、sRGB またはカスタムカラーをリス ード) トから選択できます。 • • • • • 44 | モニターの操作 Standard(標準) :デフォルトのカラー設定です。これはデフ ォルトのプリセットモードです。 Multimedia(マルチメディア) :マルチメディアアプリケーショ ンに最適です。 Movie(動画) :映画に最適です。 Game(ゲーム) :ほとんどのゲームアプリケーションに最適 です。 Paper:テキストを表示するのに最適な輝度と鮮明度の設定 をロードします。色付き画像に影響を及ぼすことなく、紙媒体 をシミュレートするために、テキストと背景を融合します。
アイコ メニューとサブ 説明 ン メニュー • • • 色温度:画面はスライダーを5,000Kに設定すると、赤/黄色 の色合いを持つ暖かい表示になります。 また、 スライダーを 10,000Kに設定すると、青の色合いを持つ涼しい表示になり ます。 sRGB: 99% sRGBをエミュレート。 カスタムカラー:手動でカラー設定を調整することができま す。 と ボタンを押して、赤、緑、青の値を調整し、独自 のプリセットカラーモードを作成します。 Input Color Format(入力 カラー形式) ビデオ入力モードを以下に設定可能です。 • RGB:モニターがHDMIケーブルを使用してコンピューター (またはDVDプレイヤー)に接続されている場合や、mDPDP、MHLケーブルを使用してMHLデバイスに接続されてい る場合にはこのオプションを選択します。 • YPbPr:お使いのDVDプレイヤーがYPbPr出力のみをサポー トしている場合にこのオプションを選択します。 Gamma(ガ ンマ) ガンマをPCまたはMACに設定できます。 色相 または を使用して、色相を0-100で調整します。 注意
アイコ メニューとサブ 説明 ン メニュー Display(ディス プレイ) 画像を調整するには、ディスプレイを使用します。 Aspect Ratio( 画像比をワイド16:9、4:3、 または5:4に調整します。 アスペクト比) Monitor Sleep(モニタ ースリープ) タイムアウト後スリープ:タイムアウト後、モニターはスリープ状態 に入ります。 スリープなし:モニターは常にスリープ状態になりません。 Sharpness(シ 画像をシャープまたはソフトにします。 ャープネス) または を使ってシャープネスを「0」〜「100」の範囲で調 整します。 動的コントラ スト コントラストレベルを高くして、 よりシャープで詳細な画質を表示 します。 ボタンを押して[ダイナミックコントラスト]の「オン」 または「オ フ」を選択します。 注意:ゲームと映画のプリセットモードのみ。 注意:ゲームモードとムービーモードを選択する場合、 ダイナミッ クコントラストではコントラストが高くなります。 応答時間 応答時間は、標準または高速に設定することが可能です。 MST DPマルチストリーム転送、オンにす
アイコ メニューとサブ 説明 ン メニュー Energy(エネル ギー) Power Button エネルギーを節約するために、電源ランプの状態を設定できま LED(電源ボタ す。 ンLED) USB モニターがスタンバイモードに入っている間、USB機能の有効ま たは無効の切り替えることができます。 注意:スタンバイモードでUSBオン/オフが利用できるのは、USB アップストリームケーブルが抜かれているときのみです。USBアッ プストリームケーブルが差し込まれているときには、 このオプショ ンはグレー表示になります。 Reset Energy このオプションを選択し、デフォルトのエネルギー設定に戻しま エネルギーの す。 リセット) モニターの操作 | 47
アイコ メニューとサブ 説明 ン メニュー Menu(メニュ ー) OSDの言語、 メニューの画面表示時間などOSD設定を調整するに は、 このオプションを選択します。 Language(言 語) 8言語から1つをOSD表示に設定します。 (英語、 スペイン語、 フランス語、 ドイツ語、ポルトガル語(ブラジル)、 ロシア語、簡体中国語、 日本語)。 回転 OSDは 0/90/180/270 度で回転します。 ディスプレイの回転に従って、 メニューを調整できます。 Transparこのオプションを選択して、 と を使用してメニューの透明度 ency(透過性) を変更します(最小値 0/最大値 100)。 Timer(タイマ ー) OSD継続時間:ボタンを押したあと、OSDがアクティブなままの時 間を設定します。 と ボタンを使用して、 スライダーを1秒刻みで5-60秒で調 整します。 Lock(ロック) ユーザーが調整にアクセスすることを制御します。ロックが選択 されている場合、ユーザーは調整できません。すべてのボタンが ロックされます。 注意:ロック機能 – ソフトロック (OSDメニューから
アイコ メニューとサブ 説明 ン メニュー Personalize(個 ショートカットキーとして設定されたプリセットモード、輝度/コント 人用設定) ラスト、入力源、 アスペクト比、回転の中から選択します。 Reset ショートカットキーを工場出荷時のデフォルトに戻します。 Personalization( 個人設定のリセ ット) Other(その他) DDC/CI、LCDコンディショニングなどOSD設定を調整するには、 このオプションを選択します。 モニターの操作 | 49
アイコ メニューとサブ 説明 ン メニュー DDC/CI DDC/CI(ディスプレイデータチャンネル/コマンドインタフェース) は、 コンピューターのソフトウェアを使ってモニター設定の調整が 可能です。 無効を選択して、 この機能をオフにします。 最高のユーザーエクスペリエンスと最適なモニターパフォーマン スのために、 この機能を有効にします。 LCD 残像の軽微な問題を低減することを助けます。 Conditioning 残像の程度によっては、 プログラムの実行に時間がかかる場合が (LCDコンディ あります。有効を選択して、 プロセスを開始します。 ショニング) Reset Other( DDC/CIのようなその他の設定を工場出荷時のデフォルトに戻し 他をリセット) ます。 Factory Reset(工場リ セット) すべてのOSD設定を工場出荷時のデフォルトに戻します。 注意:このモニターには、LED経年劣化を補正するための自動輝度較正機能が内蔵されて います。 50 | モニターの操作
OSD警告メッセージ 動的コントラストが有効に設定されている場合は( ゲームまたはムービーなどのプリセッ トモード)、手動による輝度調整は無効になります。 モニターが特定の解像度モードをサポートしない場合、次のメッセージが表示されます。 これはモニターがコンピューターから受け取る信号を同期できないことを意味していま す。 このモニターが使用できる水平および垂直周波数幅については、モニターの仕様を参 照してください。 推奨モードは2560 x 1440です。 DDC/CI機能を無効にする前に、次のメッセージが表示されます。 モニターが省電力モードに入る際には、次のメッセージが表示されます。 モニターの操作 | 51
OSDアクセスするには、コンピューターをアクティブにし、モニターを起動します。 電源ボタン以外の任意のボタンを押すと、選択した入力に応じて、次のいずれかのメッセ ージが表示されます。 DP, mDPまたはHDMI/MHL 入力が選択されているが相当するケーブルが接続されていな い場合、以下のような浮動ダイアログボックスが表示されます。 または または 詳細については、トラブルシューティングを参照してください。 52 | モニターの操作
トラブルシューティング 警告:このセクションの手順を始める前に、安全上の注意に従って下さい。 セルフテスト モニターには、お使いのモニターが正しく機能しているかをチェックできるセルフテスト機能が あります。モニターとコンピューターが正しく接続されているにもかかわらず、モニター画面が 黒いままの場合は、次のステップを実行し、モニターのセルフテストを実行してください。 1 コンピューターとモニターの電源を切ります。 2 コンピューターの裏側からディスプレイケーブルを抜きます。セルフテスト操作を正常 に行うために、 コンピューターの背面からデジタルとアナログケーブルを取り外します。 3 モニターの電源を入れます。 モニターがビデオ信号を感知せず、正しく動作する場合には、(黒色の背景に)フローテ ィングダイアログボックスが画面に表示されるはずです。 セルフテストモードの間、電源 LEDは白のまま点灯します。 また、選択した入力に応じて、下に示されるダイアログボッ クスの1つが、画面をスクロールし続けます。 または トラブルシューティング | 53
または 4 このボックスは、ビデオケーブルが切断または破損した場合にも、通常のシステム操作 時に表示されます。 5 モニターの電源を切り、ビデオケーブルを再接続します。次に、 コンピューターとモニタ ーの両方の電源を入れます。 先の手順を使用しても、モニター画面がブランクのままの場合、モニターは正しく機能し ていますので、ビデオコントローラーとコンピューターをチェックして下さい。 54 | トラブルシューティング
ビルトイン診断 モニターはビルトイン診断ツールを持ち、画面の異常がモニターに内在する問題なのか、 コンピューターやビデオカードの問題なのかを同定することに役立ちます。 注意:ビデオケーブルが抜かれ、モニターはセルフテストモードの場合のみ、ビルト イン診断を実行することができます。 ビルトイン診断を実行するには: 1 画面が汚れていないことを確認します(画面の表面に埃がないこと)。 2 コンピューターまたはモニターの裏側からビデオケーブルを抜きます。 モニターは セルフテストモードに入ります。 3 フロントパネルのボタン1とボタン4を同時に2秒間押し続けます。 灰色の画面が表 示されます。 4 注意して画面の異常を調べます。 5 フロントパネルのボタン4をもう一度押します。 画面の色が赤に変わります。 6 ディスプレイに異常がないか調べます。 7 ステップ5と6を繰り返し、緑、青、黒、白の画面で表示を調査します。 白い画面が現れると、テストは完了です。 終了するには、もう一度ボタン 4 を押します。 ビルトイン診断ツールを使用して画面の異常を検出できない場合、モニターは正常に機能 しています。 ビデオカードと
共通の問題 次の表の内容は、起こりうるモニターの問題と、可能な解決策についての一般情報です。 一般的な症状 何が発生するか 可能な解決策 ビデオなし/電源 映像なし LEDがオフ • モニターとコンピューターを繋ぐビデオケーブル が正しく、確実に接続されていることを確認しま す。 • 他の電子機器を使用して、電源コンセントが正し く機能していることを確認します。 • 電源ボタンが押し込まれていないか確認します。 • 入力ソースメニューで、正しい入力ソースが選択 されているか確認します。 ビデオなし/電源 画像または輝度 LEDがオン がない • OSDから輝度とコントラストコントロールを上げ ます。 • モニターのセルフテスト機能チェックを実行しま す。 • ビデオケーブルコネクターのピンが曲がったり、 折れていないか確認します。 • ビルトイン診断を実行します。 • 入力ソースメニューで、正しい入力ソースが選択 されているか確認します。 ピクセル抜け LCDスクリーン にスポットがあ ります。 • 電源を入れ直します。 • ピクセルが永久的に抜けているのは、LCD技術で は当然起こりうる欠
一般的な症状 何が発生するか 可能な解決策 色が出ない 画像に色がない • モニターのセルフテストを実行します。 • モニターとコンピューターを繋ぐビデオケーブルが 正しく、確実に接続されていることを確認します。 • ビデオケーブルコネクタに曲がったり破損したピン がないか、チェックします。 色がおかしい 画像の色が良く ない • アプリケーションに応じて、 カラーメニューOSDでプ リセットモードの設定を変更します。 • カスタムからR/G/Bの値を調整します。カラーメニュ ーOSDの色。 • 拡張設定OSDで、入力色形式をPC RGBまたは YPbPrに変更します。 • ビルトイン診断を実行します。 静止画像を長時 静止画像の薄い 間モニターに映 影が画面上に表 していたことによ 示される る画像の残像 • 電源管理機能を使用して、使用しないときはモニタ ーを常に切るようにします(詳細については電源管 理モードを参照してください)。 • 代わりに、動的に変化するスクリーンセーバーを使用 して下さい。 製品固有の問題 固有の症状 何が発生するか 可能な解決策 画面の画像が小 さすぎる
固有の症状 何が発生するか 可能な解決策 PCにDP接続を ブランク画面 使用していると き、画像が表示さ れない • どのDP標準(DP1.1aまたはDP1.2)がグラフィックスカ ードで認定されているか確認します。最新のグラフィ ックスカードドライバをダウンロードして、インストー ルします。 • DP1.1aグラフィックスカードの中には、DP1.2モニタ ーをサポートできないものもあります。モニター設定 をDP 1.2からDP 1.
付録 安全上の注意 光沢仕上げのベゼルの表示に関してはディスプレイの配置を考慮する必要があります。ベゼル は周辺光と明るい面からの反射を妨げる原因となります。 危険:この説明書で指定された以外の制御、調整、手順の使用は、感電、電気事故、機械的な 事故に繋がることがあります。 安全指示については安全、環境、および規制情報 (SERI) をご覧下さい。 FCC通知(米国のみ)およびその他規制情報 FCC通知およびその他の規制情報については、規制コンプライアンスWebサイトwww.dell. com/regulatory_complianceを参照してください。 Dellに連絡 注意:有効なインターネット接続がない場合には、連絡情報は仕入請求書、荷造伝票、請求 書、Dell製品カタログに掲載されています。 Dellでは複数のオンライン、電話によるサポートとサービスオプションを提供しています。国や 製品によってサービスが利用できるかどうか異なります。 また、一部のサービスはお住まいの 地域では提供していないことがあります。 オンラインモニターサポートのコンテンツを表示するには、: www.dell.
モニタのセットアップ 画面解像度を2560 x 1440(最大)に設定する 最高のパフォーマンスを達成するには、次のステップを実行してディスプレイ解像度を 2560 x 1440ピクセルに設定します。 Windows Vista、Windows 7、Windows 8、Windows 8.1 では: 1 Windows 8またはWindows 8.
Dell-以外のコンピュー Windows Vista、Windows 7、Windows 8、Windows 8.1 では: 1 Windows 8またはWindows 8.1の場合のみ、デスクトップタイルを選択してクラシックデ スクトップ表示に切り換えます。 2 デスクトップを右クリックし、個人用設定をクリックします。 3 ディスプレイの設定の変更をクリックします。 4 詳細設定をクリックします。 5 ウィンドウの上部にある説明で、お使いのビデオカードメーカー(NVIDIA、ATI、Intelな ど)を識別します。 6 グラフィックカード製造業者のWebサイトへ行き、更新されたドライバを見つけます(例 えばhttp://www.ATI.comまたはhttp://www.NVIDIA.
お手入れのガイドライン モニターの清掃 危険: モニターを清掃する前に、コンセントからモニターの電源ケーブルを抜いて ください。 警告:モニターを清掃する前に、安全上の注意を読んで、これに従ってください。 モニターの開梱、清掃、取り扱いの際には、次の一覧にある手順に従うことを推奨します。 • 静電防止スクリーンを清掃するには、柔らかい清潔な布を水でわずかに湿らせます。 できれば、スクリーン清掃専用のティッシュまたは静電防止コーティング専用の洗剤 を使用して下さい。 ベンジン、シンナー、アンモニア、研磨クリーナー、圧縮空気は 使用しないで下さい。 • モニターの清掃には、わずかに湿らせた柔らかい布を使用します。 乳状の薄膜がモニ ター表面に残ることがあるので、洗剤は使用しないでください。 • モニターを開梱する際、白い粉があった場合には、布で拭いて下さい。 • モニターは注意して取り扱って下さい。黒い色のモニターは引っ掻くと白い擦り傷が 残り、明るい色のモニターより目立ちます。 • モニターの最高画像品質を維持するために、動的に変化するスクリーンセーバーを使 用し、使用しないときにはモニターの