Dell UltraSharp 27 4K PremierColor 모니터 —UP2720Q 사용 설명서 모델 : UP2720Q 규정 모델 : UP2720Qb
참고 , 주의 및 경고 참고 : 컴퓨터를 더 잘 사용할 수 있도록 돕는 중요한 정보를 나타냅니다 . 주의 : 지침을 따르지 않을 경우 잠재적인 하드웨어 손상이나 데이터 손실을 알리는 주의가 표시됩니다 . 경고 : 경고는 물적 손해 , 신체 상해 또는 사망 가능성이 있음을 나타냅니다 . Copyright © 2019 - 2020 Dell Inc. 모든 권리 보유 . 이 제품은 미국 및 국제 저작권과 지적 재산권 법률에 의해 보호됩니다 . Dell™ 및 Dell 로고는 미국 및 / 또는 기타 관할지에서 Dell Inc. 의 상표입니 다 . Thunderbolt™ 및 Thunderbolt™ 로고는 미국 및 / 또는 기타 국가에서의 Intel Corporation 상표입니 다 . 여기에 언급된 기타 모든 마크 및 이름은 각각 해당 회사의 상표입니다 . 2020 - 12 Rev.
차례 모니터 정보 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 포장 내용물 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 제품의 특장점 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 부품과 조절 버튼 식별 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 앞면 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 뒷면 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
모니터 후드 부착 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 모니터 연결하기 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 HDMI 케이블 연결. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 DisplayPort 케이블 (DP 대 DP) 연결하기 . . . . . . . . . . . . . . . . . . . . 33 Thunderbolt™ 3 활성 케이블 연결하기 . . . . . . . . . . . . . . . . . . . . . . 33 Thunderbolt™ 멀티스트림 전송 (MST) 기능용 모니터 연결 . . . . . . 34 USB Type-C ~ Type-A 케이블 연결하기 . . . . . . . . . . . . . . . . . . .
문제 해결 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 자가 검사. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 내장형 진단 도구 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 항상 켜짐 USB Type-C (Thunderbolt™) 충전 . . . . . . . . . . 일반적 문제 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 제품 고유의 문제 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 범용 직렬 버스 (USB) 관련 문제 . . . . . . . . . . . . . . . . . . . .
모니터 정보 포장 내용물 모니터는 아래 그림에 표시된 구성 품목과 함께 제공됩니다 . 구성 품목을 받았는 지 확인한 다음 빠진 품목이 있을 경우 Dell 에 연락하십시오 . 참고 : 일부 항목은 옵션일 수 있으며 모니터와 함께 제공되지 않을 수 있습니 다 . 일부 기능 또는 매체는 특정 국가에서는 제공되지 않을 수 있습니다 . 참고 : 기타 스탠드를 설치하려면 , 스탠드 설치 안내서에 포함된 설치 지침 을 참조하십시오 .
스탠드 베이스 모니터 후드 전원 케이블 ( 국가별로 다름 ) HDMI 케이블 DP 케이블 (DP 대 DP) Thunderbolt™ 3 (USB Type-C) 활성 케이블 모니터 정보 │ 7
USB Type-C - Type-A 케 이블 • 공장 보정 보고서 • 캘리브레이션 및 검증 기술 사양서 • 간편 설치 설명서 • 안전 , 환경 및 규제 정보 8 │ 모니터 정보
제품의 특장점 Dell UP2720Q 평판 디스플레이에는 능동형 매트릭스 박막 트랜지스터 (TFT) 액 정 디스플레이 (LCD) 및 LED 백라이트가 탑재되어 있습니다 . 모니터의 특장점 에는 다음 사항이 포함됩니다 : • 68.47 cm (27 인치 ) 가시 영역 디스플레이 ( 대각선 측정 시 ). 3840 x 2160 (16:9) 해상도를 제공하며 좀 더 낮은 해상도의 경우 전체 화면 모드를 지원합니다 . • 시야각이 넓어 앉은 위치에서 또는 서 있는 위치에서 화면을 볼 수 있습 니다 . • 색역 CIE1931 Adobe 100% 및 CIE1976 DCI-P3 98% 로 평균 Delta E < 2 입 니다 . • HDMI, DP 및 Thunderbolt™ 3 소스를 지원합니다 . • HDMI, DP 및 Thunderbolt™ 3 연결은 60 Hz 에서 10 비트 색을 지원합니다 .
부품과 조절 버튼 식별 앞면 전면 패널 조절 버튼 라벨 1 2 설명 기능 버튼 ( 자세한 내용은 모니터 조작 참조 ) 전원 버튼 (LED 표시기 포함 ) 10 │ 모니터 정보
뒷면 모니터 스탠드 장착 및 미장착 상태의 뒷면 라벨 1 설명 사용 VESA 설치 구멍 (100 mm x 100 mm 뒤쪽에 부착된 VESA 덮개 ) VESA 호환형 벽면 설치 키트를 사용하는 벽걸이형 모니터 (100 mm x 100 mm). 2 규정에 의한 라벨 규정에 의한 승인을 표시합니다 . 3 스탠드 분리 버튼 스탠드를 모니터에서 분리합니다 . 4 바코드 , 일련번호 및 서비스 태그 레이블 Dell 기술 지원 요청용 . 5 케이블 관리 구멍 케이블을 구멍을 통과하도록 하여 케이블 을 정리하는 데 사용됩니다 .
밑면 아래 모습 ( 모니터 스탠드 없음 ) 라벨 1 AC 전원 커넥터 전원 케이블 ( 모니터에 포함됨 ) 을 연결합니다 . 2 보안 잠금 슬롯 보안 잠금을 사용하여 모니터를 보호합니다 ( 보안 잠금은 포함되어 있지 않음 ). 3 (1, 2) HDMI 포트 커 넥터 컴퓨터에 HDMI 케이블을 연결합니다 . 4 DisplayPort 입력 커넥터 컴퓨터에 DP 케이블을 연결합니다 . 5 오디오 라인 출력 스피커에 연결합니다 .* Thunderbolt™ 3 업스트림 (USB Type-C) 포트 모니터와 함께 제공된 Thunderbolt™ 3 활성 케이 블을 컴퓨터 또는 모바일 장치에 연결합니다 . 이 포트는 USB 전원 공급 ( 최대 90 W), 데이터 및 DisplayPort 비디오 신호를 지원합니다 . 6-1 설명 사용 Thunderbolt™ 3 포트는 교대 모드 DP1.4, 60 Hz, PD 20 V/4.
참고 : Thunderbolt™ 3 은 Windows 10 이전의 Windows 에서 지원되지 않습니다 . 6-2 Thunderbolt™ 3 다운스트림 (USB Type-C) 포트 모니터와 함께 제공된 Thunderbolt™ 3 활성 케이 블을 컴퓨터 , 모바일 장치 , 보조 모니터 또는 다 른 Thunderbolt™ 장치에 연결합니다 . 이 포트는 USB 전원 공급 ( 최대 15W, PD 5 V/3 A), 데이터 및 DisplayPort 비디오 신호를 지원합니다 . Thunderbolt™ 3 은 MST( 멀티 스트림 전송 ) 가 가 능한 모니터를 지원합니다 . MST 를 활성화하 려 면 , “Thunderbolt ™ 멀티스트림 전송 (MST) 기 능용 모니터 연결 ” 섹션의 지침을 참조하십시오 . 참고 : 15 W 이상의 전원을 필요로 하는 노트북 및 다른 장치의 경우 , 다른 전원에 연결하여 장치의 전원을 공급하거나 충전할 것을 권장합니다 .
모니터 규격 평판 규격 모델 UP2720Q 화면 유형 능동형 매트릭스 - TFT LCD 패널 기술 평면에서 교환 유형 화면비 16:9 볼 수 있는 이미지 대각 684.7 mm (27 인치 ) 수평 , 활성 영역 596.74 mm (23.49 인치 ) 수직 , 활성 영역 335.66 mm (13.21 인치 ) 영역 200301 mm2 (310.47 인치 2) 픽셀 피치 0.1554 mm x 0.
캘리브레이션 정확도 Delta E < 2 ( 평균 ) 연결성 참고 : CIE1931 Adobe 100% 및 CIE1976 DCI-P3 98% 만 해당 . • 1 x DP 1.4 (HDCP 2.2) • 2 x HDMI 2.0 (HDCP 2.2) • 1 x Thunderbolt™ 3 업스트림 포트 (DP1.4) • 1 x Thunderbolt™ 3 다운스트림 포트 (DP1.4) • 2 x USB 3.2 Gen2 다운스트림 포트 • 2 x USB 3.2 Gen1 다운스트림 포트(1 x BC1.2 충전 능력 , 2 A( 최대 )) 테두리 너비 ( 모니터 가장자리에서 활성 영역 까지 ) 7.6 mm( 상단 ) 7.6 mm( 왼쪽 / 오른쪽 ) 27.
지원되는 비디오 모드 모델 UP2720Q 비디오 디스플레이 기능 (HDMI 재생 ) 480p, 576p, 720p, 1080i, 1080p, QHD, UHD ( 인터레이싱 모드는 PBP 모드 하에서 지원되지 않습니다 ) 사전 설정 디스플레이 모드 디스플레이 모드 수평주파수 (kHz) 수직주파수 (Hz) 픽셀클록 (MHz) VESA, 640 x 480 31.5 59.9 25.2 동기 극성 ( 수평 / 수직 ) -/- VESA, 640 x 480 37.5 75.0 31.5 -/- VESA, 720 x 400 31.5 70.1 28.3 -/+ VESA, 800 x 600 37.9 60.3 40.0 +/+ VESA, 800 x 600 46.9 75.0 49.5 +/+ VESA, 1024 x 768 48.4 60.0 65.0 -/- VESA, 1024 x 768 60.0 75.0 78.8 +/+ VESA, 1152 x 864 67.
다중 스트림 전송 (MST) 모드 MST 소스 모니터 최대 수의 외부 모니터가 지원될 수 있습니다 3840 x 2160 (60 Hz 일 때 ) 3840 x 2160 60 Hz 에서 1 참고 : Thunderbolt™ 다중 스트림 전송 (MST) 연결을 위해 모니터와 함께 제공된 케이블을 사용하십시오 . 연결에 대한 자세한 내용은 Thunderbolt ™ 멀티스트림 전송 (MST) 기능용 모니터 연결를 참조하십 시오 . 전기 규격 모델 UP2720Q 비디오 입력 신호 HDMI 2.0*/DP 1.4, 각 라인당 600 mV, 각 쌍당 100 오옴의 입력 임피던스 . AC 입력 전압 / 주파수 / 전류 100 VAC ~ 240 VAC / 50 Hz 또는 60 Hz + 3 Hz / 2.8 A ( 일반 ) 돌입 전류 • 120 V: 40 A ( 최대 ) 0°C 에서 ( 콜드 스타트 ) • 240 V: 80 A ( 최대 ) 0°C 에서 ( 콜드 스타트 ) 소비 전력 • 0.
3 Pon: 켜기 모드의 소비 전력은 Energy Star 테스트 방법을 기준으로 측정됩 니다 . TEC: kWh 로 나타낸 총 에너지 소비는 Energy Star 테스트 방법을 기준으로 측 정됩니다 . 이 문서는 정보용으로서 실험실 성능을 반영합니다 . 사용자의 실제 제품은 주 문한 소프 트웨어 , 구성요소 , 주변장치에 따라 성능이 이와 다를 수 있으며 , 당 사는 이러한 정보를 업데이트해야 할 의무가 없습니다 . 따라서 고객은 전기적 공차 또는 기타 사항에 대한결 정을 내리는 데 이 정보에 의존해서는 안 됩니다 . 정확성 또는 완전성에 대해 어떠한명시 적 또는 묵시적 보증도 하지 않습니다 . 물리적 특성 모델 UP2720Q 커넥터 유형 • 1 x DP 1.4 • 2 x HDMI 2.0 • 1 x Thunderbolt™ 3 업스트림 (DP1.4) • 1 x Thunderbolt™ 3 다운스트림 (DP1.4) • 2 x USB 3.2 Gen2 다운스트림 포트 • 2 x USB 3.
치수 ( 스탠드 포함 ) 높이 ( 연장 시 ) 563.4 mm (22.18 인치 ) 높이 ( 축소했을 때 ) 433.4 mm (17.06 인치 ) 너비 611.9 mm (24.09 인치 ) 깊이 212.0 mm (8.35 인치 ) 치수 ( 스탠드 미포함 ) 높이 376.8 mm (14.83 인치 ) 너비 611.9 mm (24.09 인치 ) 깊이 51.0 mm (2.01 인치 ) 스탠드 치수 높이 ( 연장 시 ) 456.3 mm (17.96 인치 ) 높이 ( 축소했을 때 ) 408.9 mm (16.10 인치 ) 너비 260.0 mm (10.24 인치 ) 깊이 212.0 mm (8.35 인치 ) 중량 중량 ( 포장 포함 ) 14.14 kg (31.17 lb) 스탠드 어셈블리와 케이블을 포함 한 중량 9.71 kg (21.41 lb) 중량 ( 스탠드 어셈블리 미포함 ) ( 벽 설치 또는 VESA 설치를 위한 고려사항의 경우 - 케이블 없음 ) 5.
환경 특성 모델 UP2720Q 준수 표준 • RoHS- 규격 • TCO 인증 디스플레이 • 외부 케이블을 제외하고 BFR/PVC 없음 ( 할로겐 없음 ) • 비소 없는 유리와 수은 없는 패널만 해당됩니다 온도 동작 0°C ~ 40°C (32°F ~ 104°F) 비동작 • 보관 : -20°C ~ 60°C (-4°F ~ 140°F) • 운반 : -20°C ~ 60°C (-4°F ~ 140°F) 습도 동작 10% ~ 90% ( 비응축 ) 비동작 • 보관 : 10% ~ 90% ( 비응축 ) • 운반 : 10% ~ 90% ( 비응축 ) 고도 동작 3,048 m (10,000 피트 ) ( 최대 ) 비동작 12,192 m (40,000 피트 ) ( 최대 ) 열 분산 • 784.76 BTU/ 시간 ( 최대 ) • 150.
핀 지정 DisplayPort 커넥터 핀 번호 1 연결된 신호 케이블의 20 핀 면 ML3 (n) 2 GND 3 ML3 (p) 4 ML2 (n) 5 GND 6 ML2 (p) 7 ML1 (n) 8 GND 9 ML1 (p) 10 ML0 (n) 11 GND 12 ML0 (p) 13 GND 14 GND 15 AUX (p) 16 GND 17 AUX (n) 18 핫 플러그 감지 19 Re-PWR 20 +3.
HDMI 커넥터 핀 번호 1 연결된 신호 케이블의 19 핀 면 TMDS 데이터 2+ 2 TMDS 데이터 2 쉴드 3 TMDS 데이터 2- 4 TMDS 데이터 1+ 5 TMDS 데이터 1 쉴드 6 TMDS 데이터 1- 7 TMDS 데이터 0+ 8 TMDS 데이터 0 쉴드 9 TMDS 데이터 0- 10 TMDS 클록 + 11 TMDS 클록 쉴드 12 TMDS 클록 - 13 CEC 14 예약됨 ( 장치의 N.C.
플러그 앤 플레이 기능 이 모니터는 어떠한 플러그 앤 플레이 호환 시스템에든 설치할 수 있습니다 . 모 니터는 디스플레이 데이터 채널 (DDC) 프로토콜을 사용하여 컴퓨터 시스템에 확장 디스플레이 식별 데이터 (EDID) 를 제공함으로써 시스템이 자체적으로 구 성하고 모니터 설정을 최적화도록 합니다 . 대다수 모니터 설치는 자동으로 실행 되므로 원할 경우 다른 설정을 선택할 수 있습니다 . 모니터 설정 변경에 대한 자 세한 내용은 모니터 조작를 참조하십시오 . 범용 직렬 버스 (USB) 인터페이스 이 단원에서는 모니터에 탑재된 USB 포트에 대한 정보를 제공합니다 . 참고 : 이 모니터는 초고속 USB 3.2 호환입니다 . 전송 속도 소비 전력 * 초고속 데이터 전송 속도 10 Gbps 4.5 W ( 최대 , 각 포트 ) 고속 480 Mbps 4.5 W ( 최대 , 각 포트 ) 완속 12 Mbps 4.5 W ( 최대 , 각 포트 ) * BC1.
USB 다운스트림 커넥터 핀 번호 1 커넥터의 9 핀 쪽 VCC 2 D- 3 D+ 4 GND 5 SSRX- 6 SSRX+ 7 GND 8 SSTX- 9 SSTX+ Thunderbolt™ 3 커넥터 핀 번호 A1 신호 이름 GND 핀 번호 B1 케이블 감지 A2 TX1+ B2 TX2+ A3 TX1- B3 TX2- A4 VBUS B4 VBUS A5 CC1 B5 CC2 A6 D+ B6 D+ A7 D- B7 D- A8 SBU1 B8 SBU2 A9 VBUS B9 VBUS 24 │ 모니터 정보 신호 이름
A10 RX2- B10 RX1- A11 RX2+ B11 RX1+ A12 GND B12 GND USB 포트 • 1 x Thunderbolt™ 3 다운스트림 (USB Type-C 호환 ) - 하단 • 1 x Thunderbolt™ 3 업스트림 (USB Type-C 호환 ) - 하단 • 2 x USB 3.2 Gen2 다운스트림 - 하단 • 2 x USB 3.2 Gen1 다운스트림 - 하단 • 충전 포트 배터리 아이콘이 있는 포트 ; BC1.2 호환 장치인 경우 신 속 충전 기능을 지원합니다 . 참고 : USB 3.2 기능을 사용하려면 USB 3.2 을 지원하는 컴퓨터가 있어야 합니다 . 참고 : 모니터의 USB 포트는 모니터가 켜져 있거나 대기 모드에 있을 때만 동작합니다 . 모니터를 껐다 켜면 연결된 주변장치가 정상 기능을 재작동시 키는 데 몇 초가 걸릴 수 있습니다 .
• 모니터를 청소할 때는 따뜻한 물에 약간 적신 헝겊을 사용하십시오 . 일부 세제는 모니터에 유백색의 엷은 막을 형성하므로 어떠한 종류의 세제도 사 용하지 마십시오 . • 모니터의 포장을 풀었을 때 백색 분말이 보이면 헝겊으로 닦아 내십시오 . • 짙은 색의 모니터가 긁히면 밝은 색의 모니터보다 흠집이 더 잘 보일 수 있 으므로 모니터를 주의하여 다루십시오 . • 모니터에 최고 품질의 이미지가 표시되게 하려면 동적으로 변화하는 화면 보호기를 사용하고 , 사용하지 않을 때는 모니터를 끄십시오 .
모니터 설치 스탠드 부착하기 참고 : 스탠드는 모니터에서 분리되어 출고됩니다 . 참고 : 이것은 스탠드 장착형 모니터에 적용될 수 있습니다 . 스탠드 설치 안 내서에 포함된 설치 지침을 참조하십시오 . 주의 : 스탠드를 부착하기 전에 모니터를 포장 상자에서 제거하지 마십시오 . 모니터 스탠드 부착하기 : 1. 상자 반대편에 적힌 지침을 따라 스탠드를 고정시키는 위쪽 쿠션에서 스탠 드를 빼냅니다 . 2. 스탠드 받침 블록을 스탠드 슬롯에 완전히 삽입합니다 . 3. 나사 핸들을 들어 올리고 나사를 시계 방향으로 돌립니다 . 4. 나사를 조인 후 , 나사 핸들을 우묵한 부분에 평평하게 접어 넣습니다 .
5. 그림과 같이 덮개를 들어올려 스탠드 어셈블리를 위해 VESA 영역을 노출시 킵니다 . 6. 스탠드 어셈블리를 모니터에 부착하십시오 . a. 모니터 후면의 홈을 스탠드 상부에 있는 두 개의 탭에 끼웁니다 . b. 스탠드를 딸깍 소리가 나면서 정위치에 고정될 때까지 누릅니다 .
7. 모니터를 똑바로 세웁니다 . 참고 : 미끄러지거나 떨어지지 않도록 모니터를 조심해서 들어올립니다 . 주의 : 모니터를 옮길 때 비색계 트레이를 잡거나 들어 올리지 마십시오 . 8. 모니터에서 덮개를 제거합니다 .
모니터 후드 부착 모니터 후드 설치하기 : 1. 모니터와 함께 제공된 후드를 꺼냅니다 . 2. 두 플랩에 있는 “U” 채널 스트립이 안쪽을 향하도록 하여 후드를 펼칩니다 .
3. 모니터 측면을 “U” 채널 스트립 안에 맞춥니다 . 4. 후드를 아래로 밉니다 . 모니터 연결하기 경고 : 이 단원에 있는 절차를 시작하기 전에 안전 지침을 따르십시오 . 참고 : 모든 케이블을 컴퓨터에 동시에 연결하지 마십시오 . 모니터를 컴퓨터에 연결하기 : 1. 컴퓨터를 끄고 전원 케이블을 뽑습니다 . 2. HDMI/DP/Thunderbolt™ 3 활성 케이블로 모니터를 컴퓨터 또는 장치에 연 결합니다 .
HDMI 케이블 연결 참고 : UP2720Q 의 공장 설정 기본값은 HDMI 2.0 입니다 . HDMI 케이블이 연결된 후 모니터에 내용이 표시되지 않는 경우 , 아래 절차에 따라 설정을 HDMI 2.0 에서 HDMI 1.4 로 변경하십시오 : • • 버튼 옆의 두번째 버튼을 눌러 OSD 메뉴를 활성화합니다 . 및 버튼을 사용하여 Input Source( 입력 소스 ) 를 선택한 다음 버튼을 사용하여 하위 메뉴로 들어갑니다 . • 및 버튼을 사용하여 HDMI 를 선택합니다 . • 버튼을 약 10 초 동안 누르고 있으면 , HDMI 구성 메시지가 나타납 니다 . • 버튼을 사용하여 Yes( 예 ) 를 선택하고 설정을 변경합니다 . 필요한 경우 위의 단계를 반복하여 HDMI 형식 설정을 변경합니다 .
DisplayPort 케이블 (DP 대 DP) 연결하기 참고 : UP2720Q 의 공장 설정 기본값은 DP 1.4 입니다 . Thunderbolt™ 3 활성 케이블 연결하기 참고 : 모니터에 포함되어 있는 Thunderbolt™ 3 활성 케이블만 사용하십 시오 . • • • • 이 포트는 DisplayPort 교대 모드 DP 1.4 를 지원합니다 . Thunderbolt™ 3 전원 공급 호환 포트 (PD 버전 3.0) 는 최대 90 W 의 전 력을 공급합니다 . 노트북이 작동하는 데 90 W 이상이 필요하거나 배터리가 방전된 경우 , UP2720Q 의 USB PD 포트를 사용하여 전원을 공급하거나 충전하지 못 할 수도 있습니다 . Thunderbolt™ 3 은 Windows 10 이전의 Windows 에서 지원되지 않습 니다 . 참고 : UP2720Q 모니터는 USB-C Thunderbolt™ 3 활성 케이블과 함께 제 공됩니다 . USB-C DP 케이블은 포함되어 있지 않습니다 .
Thunderbolt™ 멀티스트림 전송 (MST) 기능용 모니터 연결 참고 : UP2720Q 는 Thunderbolt™ MST 기능을 지원합니다 . 이 기능을 이 용하려면 , PC 가 Thunderbolt™ 기능을 지원해야 합니다 . UP2720Q 의 공장 설정 기본값은 교대 모드 DP 1.4 입니다 . MST 연결을 설정하려면 , 모니터와 함께 제공된 Thunderbolt™ 3 활성 케이블만 사용하고 , 아래 단계를 수행합니다 : 1. 컴퓨터를 끄고 전원 케이블을 뽑습니다 . 2. Thunderbolt™ 3 활성 케이블을 모니터 1 의 Thunderbolt™ 업스트림 포트로 부터 컴퓨터 또는 장치에 연결합니다 . 3. 다른 Thunderbolt™ 3 활성 케이블을 모니터 1 의 Thunderbolt™ 다운스트림 포트에서 모니터 2 의 Thunderbolt™ 업스트림 포트에 연결합니다 .
참고 : USB-C DP 로 연결하는 컴퓨터를 사용하는 경우 , 별도로 USB-C DP 케이블을 구매하십시오 . 자세한 내용을 보려면 다음 위치로 가십시오 : http://www.dell.com. 참고 : Thunderbolt™ 3 패시브 케이블 구매에 대한 정보를 보려면 다음 위치 로 가십시오 : Thunderbolt ™ 3 패시브 케이블 구매 . USB Type-C ~ Type-A 케이블 연결하기 참고 : 데이터 손상이나 손실을 방지하기 위해 , USB 업스트림 포트에서 연 결을 해제하기 전에 모니터의 Thunderbolt™ 3 업스트림 포트에 연결된 컴 퓨터에 의해 사용 중인 USB 저장 장치가 " 없는지 " 확인하십시오 . DisplayPort/HDMI 케이블을 연결한 뒤 아래 절차를 따라 USB Type-C ~ Type-A 케이블을 컴퓨터에 연결하고 모니터 설치를 완료합니다 : 1.
케이블 정리하기 필요한 모든 케이블을 모니터와 컴퓨터에 연결한 후 ( 케이블 연결은 모니터 연 결하기를 참조 ) 케이블 관리 슬롯을 사용하여 위와 같이 모든 케이블을 깔끔하 게 정리합니다 .
모니터 스탠드 분리하기 참고 : 스탠드를 분리하는 중에 곡선 LCD 화면의 긁힘과 손상을 방지하기 위 해 , 모니터를 부드럽고 깨끗한 스티로폼에 놓습니다 . 딱딱한 물체에 직접 닿으면 곡선 모니터가 손상을 입을 수 있습니다 . 참고 : 이것은 스탠드 장착형 모니터에 적용될 수 있습니다 . 스탠드 설치 안 내서에 포함된 설치 지침을 참조하십시오 . 스탠드 분리하기 : 1. 모니터를 부드러운 천이나 쿠션 위에 놓습니다 . 2. 스탠드 분리 버튼을 누른 채로 있습니다 . 3. 덮개 래치를 누르면서 들어올려 풀고 덮개를 제거합니다 .
벽걸이 ( 별매 ) ( 나사 치수 : M4 x 10 mm). VESA 호환형 벽걸이 키트와 함께 제공되는 지침을 참조하십시오 . 1. 안정된 평평한 탁자에 부드러운 천 또는 쿠션을 깔고 모니터 패널을 그 위 에 올려 놓습니다 . 2. 스탠드를 제거합니다 . 3. Phillips 십자 스크루드라이버를 사용하여 플라스틱 커버를 고정하는 네 개 의 나사를 제거합니다 . 4. 벽걸이 키트의 장착 브래킷을 모니터에 부착합니다 . 5. 벽걸이 키트와 함께 제공되는 지침을 따라 모니터를 벽에 장착합니다 . 참고 : 최소 중량 / 하중 지지 용량이 22.4 kg 인 UL 인증 벽걸이 브래킷하고 만 사용할 수 있습니다 .
모니터 조작 모니터 전원 켜기 모니터를 켜려면 버튼을 누릅니다 . 전면 패널 사용하기 모니터 전면의 제어 버튼을 사용하여 설정을 조정합니다 . 다음 표에서는 전면 패널 버튼에 대해 설명합니다 : 전면 패널 버튼 설명 이 단축 키를 선택하면 사전 설정 컬러 모드의 목록 중에서 선택할 수 있습니다 .
이 버튼을 사용하여 입력 소스를 선택합니다 . 2 바로 가기 키 / Input Source ( 입력 소스 ) 이 버튼을 사용하여 색 보정 시퀀스를 시작합니 다. 3 바로 가기 키 / Calibrate Now ( 지금 보정 ) 4 바로 가기 키 / Display Info ( 디스플레이 정보 ) 5 메뉴 이 버튼을 사용하여 모니터의 현재 설정을 표시 합니다 . 메뉴 버튼을 사용하여 OSD( 온스크린 디스플레 이 ) 를 실행합니다 . 메뉴 시스템 액세스하기을 참조하십시오 . 이 버튼을 사용하여 OSD 메인 메뉴를 종료합 니다 . 6 종료 전원 버튼을 사용하여 모니터를 켜고 끕니다 . 7 전원 ( 전원 표시등 ) 40 │ 모니터 조작 흰색 불이 켜져 있는 것은 모니터가 켜졌고 정상 작동 중임을 나타냅니다 . 흰색 불이 깜박이는 것은 모니터가 대기 모드에 있음을 나타냅니다 .
전면 패널 버튼 모니터 전면 버튼을 사용하여 이미지 설정을 조정합니다 . 전면 패널 버튼 1, 2 기능 없음 설명 이 버튼은 기능이 없습니다 . 위로 버튼을 사용하여 OSD 메뉴의 항목을 조정합니다 ( 범위 증가 ). 3 위로 아래로 버튼을 사용하여 OSD 메뉴의 항목을 조정합니다 ( 범위 감소 ). 4 아래로 Enter 버튼을 사용하여 하위 메뉴로 들어갑니다 . 5 Enter 이 버튼을 사용하여 OSD 메인 메뉴를 종료합니다 .
OSD 메뉴 사용하기 메뉴 시스템 액세스하기 참고 : 설정을 변경하고 다른 메뉴로 가거나 OSD 메뉴를 종료하면 모니터가 자동으로 이 변경 내용을 저장합니다 . 설정을 변경한 다음 OSD 메뉴가 사라 지길 기다리는 동안에도 변경 내용이 저장됩니다 . 1. 버튼을 눌러 OSD 메뉴를 실행하여 주 메뉴를 표시합니다 . 2. 및 버튼을 눌러 설정 옵션 사이에서 이동합니다 . 한 아이콘에서 다 른 아이콘으로 이동할 때 옵션 이름이 강조 표시됩니다 . 모니터에서 사용 할 수 있는 모든 옵션의 전체 목록은 아래 표를 참조하십시오 . 3. 버튼을 한 번 눌러 강조 표시된 옵션을 활성화합니다 . 4. 및 5. 를 눌러 하위 메뉴로 들어간 다음 방향 버튼을 사용하여 메뉴에 있는 표 버튼을 눌러 원하는 파라미터를 선택합니다 . 시기를 따라 변경합니다 . 6. 버튼을 선택하여 주 메뉴로 돌아갑니다 .
아이콘 메뉴 및 하위 메뉴 Color( 색 ) Color Space ( 색 공간 ) 설명 Color( 색 ) 을 사용하여 색상 설정 모드를 조정합 니다 . Color Space( 색 공간 ) 를 선택하면 다음 중 하나를 선택할 수 있습니다 : DCI P3 D65 G2.4 L100, BT.709 D65 BT1886 L100, BT.2020 D65 BT1886 L100, sRGB D65 sRGB L250, Adobe RGB D65 G2.2 L250, Adobe RGB D50 G2.2 L250, Native( 원시 ), Custom 1( 사용자 지정 1), Custom 2( 사용자 지정 2), Custom 3( 사용자 지정 3), CAL 1, 또는 CAL 2. 참고 : 공장 사전 설정 모드 DCI P3 D65 G2.4 L100 은 DCI-P3 사양 (P3 화이트 포인트 , 48 cd/m2) 과 다릅니 다 .
참고 : Factory Reset( 공장 초기화 ) 으로 보정된 데 이터가 삭제되지 않습니다 . 사용자는 Color( 색 ) > Color Space( 색 공간 ) > Reset this Color Space # (Ponovno postavi ovaj prostor boja #) (1~6) 으로 이 동하여 수동으로 선택한 보정 데이터를 제거할 수 있 습니다 . CAL 1 및 CAL 2 의 보정 데이터는 OSD 에서 제거할 수 없습니다 . 모니터 색상 설정을 공장 설정으로 초기화합니다 . Reset Color ( 색상 초기화 ) Luminance Luminance( 휘도 ) 는 백라이트의 휘도를 조정합 ( 휘도 ) 니다 . 버튼을 누르면 휘도가 증가하고 버튼을 누르 면 휘도가 감소합니다 ( 최소 45 / 최대 250). 참고 : Color Space( 색 공간 ) 을 CAL 1 또는 CAL 2 에 설정하면 , Luminance( 휘도 ) 가 회색으로 변합 니다 .
Input Source ( 입력 소스 ) Input Source( 입력 소스 ) 메뉴를 사용하여 모니터에 연결할 수 있는 서로 다른 비디오 신호 중에서 선택합 니다 . Thunderbolt Thunderbolt™ 3 커넥터를 사용하고 있을 때는 Thunderbolt 입력을 선택합니다 . DP Thunderbolt 입력 소스를 선택합니다 . DisplayPort (DP) 커넥터를 사용하고 있을 때는 DP 입 력을 선택합니다 . HDMI 1 버튼을 눌러 HDMI 1 입력 소스를 선택 합니다 . HDMI 2 커넥터를 사용하고 있을 때는 HDMI 2 입력을 선택합니다 . Auto Select ( 자동 선택 ) 버튼을 눌러 DP 입력 소스를 선 택합니다 . HDMI 1 커넥터를 사용하고 있을 때 HDMI 1 입력을 선 택합니다 . HDMI 2 버튼을 눌러 버튼을 눌러 HDMI 2 입력 소스를 선 택합니다 . 기능을 켜면 사용 가능한 입력 소스를 스캔할 수 있습 니다 .
Auto Select for Auto Select for Thunderbolt(Thunderbolt 자동 선 Thunderbolt 택 ) 을 다음으로 설정할 수 있습니다 : (Thunderbolt • Prompt for Multiple Inputs( 복수 입력에 대한 프 자동 선택 ) 롬프트 ): 사용자가 전환 여부를 선택할 수 있도록 항상 "Switch to Thunderbolt Video Input" (Thunderbolt 비디오 입력으로 전환 ) 메시지를 표 시합니다 . • Yes( 예 ): Thunderbolt™ 3 활성 케이블이 연결되어 있을 때 ( 묻지 않고 ) 항상 Thunderbolt 비디오 입 력으로 전환합니다 . • No( 아니요 ): Thunderbolt™ 3 활성 케이블이 연결 되어 있을 때 자동으로 Thunderbolt 비디오 입력 으로 전환되지 않습니다 .
이미지 비율을 Auto Resize( 자동 크기 조정 ), 17:9, 16:9 또는 Pixel-for-Pixel( 픽셀에 대한 픽셀 ) 로 조 정합니다 . Digital Cinema Digital Cinema Masking( 디지털 시네마 마스킹 ) 을 Masking Entire DCI Container( 전체 DCI 컨테이너 ), DCI ( 디지털 시네마 1.85:1, DCI 2.39:1 또는 DCI 2.35:1 로 조정합니다 . 마스킹 ) Markers Markers( 마커 ) 를 No Markers( 마커 없음 ), 1.85:1, ( 마커 ) 2.39:1, 2.
Response Time Response Time( 응답 시간 ) 을 Normal( 보통 ), ( 응답 시간 ) Fast( 고속 ) 또는 Off( 꺼짐 ) 으로 설정할 수 있습니 다. 참고 : Response Time( 응답 시간 ) 은 색의 정확성을 보장하기 위해 보정 및 확인 동안 자동으로 패널 기본 값으로 재설정됩니다 . Uniformity 화면 균일성 보정 설정을 선택합니다 . On( 켜짐 ) 은 Compensation 기본적으로 공장 보정된 설정입니다 . Uniformity ( 균일성 보정 ) Compensation( 균일성 보정 ) 은 화면 전체에 걸쳐 균일한 밝기와 색상을 표시하도록 중심이 아닌 다른 영역 들을 조정합니다 . 참고 : Uniformity Compensation( 균일성 보정 ) 을 켠 상태에서는 공장에서 기본으로 설정된 휘도를 사 용할 것을 권장합니다 . 레벨이 다른 휘도 설정을 사용 할 경우 , 균일 성능이 공장 보정 보고서에 표시된 데 이터와 편차를 보일 수 있습니다 .
PBP Mode (PBP 모드 ) PBP(Picture by Picture) 모드를 AA, AB 또는 Off ( 꺼짐 ) 으로 조정합니다 . 버튼을 사용하여 PBP 모드를 활성화합니다 .
PBP (Sub) PBP 하위 창에 대해 모니터에 연결된 여러 가지 비디 (PBP ( 서브 )) 오 신호 간을 전환합니다 . 버튼을 눌러 PBP 하위 창 소스 신호를 선택합니다 . PBP Input 선택하여 PBP 모드에서 입력 소스 간을 전환합니다 . Source Toggle 버튼을 눌러 PBP 모드에서 입력 소스 간을 전환합 (PBP 입력 소스 니다 . 토글 ) Video Swap ( 비디오 스왑 ) 참고 : PBP 모드가 AA 에 설정되어 있을 때는 사용할 수 없습니다 . PBP 모드에서 메인 창과 하위 창 간에 비디오를 스왑 하려면 선택합니다 . 버튼을 눌러 메인 창과 하위 창을 스왑합니다 . Color Gamut (Sub)( 색역 ( 서브 )) 를 DCI P3, BT.709, BT.2020, sRGB, Adobe RGB 또는 Native ( 원시 ) 로 조정합니다 .
Gamma (Sub) Gamma (Sub)( 감마 ( 서브 )) 를 1.6, 1.8, 2.0, 2.2, ( 감마 ( 서브 )) 2.4, 2.6, BT.1886, sRGB 또는 Native( 원시 ) 로 조정 합니다 . Sharpness (Sub)( 선명도 ( 서브 )) 참고 : Color Gamut (Sub)( 색역 ( 서브 )) 가 Native ( 원시 ) 로 설정되어 있을 때는 사용할 수 없습니다 . PBP 모드에서 이미지의 선명도 수준을 조정합니다 . 버튼을 누르면 선명도가 증가하고 버튼을 누 르면 선명도가 감소합니다 . Audio( 오디오 ) 메인 창 또는 하위 창에서 오디오 소스를 설정할 수 있 습니다 . Video Data Video Data Range( 비디오 데이터 범위 ) 를 Auto Range( 비디오 ( 자동 ), Full( 전체 ) 또는 Limited( 제한됨 ) 으로 조 데이터 범위 ) 정합니다 . Reset PBP 이 옵션을 선택하면 기본 PBP 설정이 복구됩니다 .
Calibration Target ( 보정 대상 ) Calibration Speed ( 보정 속도 ) 보정 대상을 DCI P3 D65 G2.4 L100, BT.709 D65 BT1886 L100, BT.2020 D65 BT1886 L100, sRGB D65 sRGB L250, Adobe RGB D65 G2.2 L250, Adobe RGB D50 G2.2 L250, CAL 1 또는 CAL 2 에 설정할 수 있습니다 . 참고 : 다음 Color Space( 색 공간 ) 옵션은 보정 대상 으로 사용할 수 없습니다 : Native( 원시 ), Custom 1 ( 사용자 지정 1), Custom 2( 사용자 지정 2) 및 Custom 3( 사용자 지정 3). 보정 속도를 Express( 고속 ) 또는 Comprehensive ( 종합 ) 으로 설정할 수 있습니다 . 참고 : Express( 고속 ) 를 선택하면 보정 시간이 대략 4 분 걸립니다 .
Calibration Calibration Module Power( 보정 모듈 전원 ) 을 On Module Power ( 켜짐 ) 또는 Off( 꺼짐 ) 으로 설정할 수 있습니다 . ( 보정 모듈 참고 : Calibration Module Power( 보정 모듈 전원 ) 전원 ) 을 On( 켜짐 ) 으로 설정해야 Calibration( 보정 ) 기 능을 사용할 수 있습니다 . Show Last 가장 최근의 보정 결과를 살펴볼 수 있습니다 . Calibration Results ( 마지막 보정 결 과 표시 ) Validation 내장된 비색계를 사용해 색상 보정에 대한 유효성 확 ( 확인 ) 인을 수행합니다 . Validate Now ( 지금 확인 ) Validation Target ( 확인 대상 ) 색상 확인을 시작할 수 있습니다 . 확인 대상을 DCI P3 D65 G2.4 L100, BT.709 D65 BT1886 L100, BT.
Calibration Calibration Module Power( 보정 모듈 전원 ) 을 On Module Power ( 켜짐 ) 또는 Off( 꺼짐 ) 으로 설정할 수 있습니다 . ( 보정 모듈 참고 : Calibration Module Power( 보정 모듈 전원 ) 전원 ) 을 On( 켜짐 ) 으로 설정해야 Validation( 확인 ) 기능 을 사용할 수 있습니다 . Show Last 가장 최근의 확인 결과를 살펴볼 수 있습니다 . Validation Results ( 마지막 확인 결 과 표시 ) Scheduler 자동 보정 또는 확인에 대한 일정을 설정합니다 . ( 스케줄러 ) Scheduler( 스케줄러 ) 를 Off( 꺼짐 ), Calibration ( 보정 ), Validation( 확인 ) 또는 Calibration + Validation( 보정 + 확인 ) 으로 설정할 수 있습니다 .
Menu( 메뉴 ) 이 옵션을 선택하여 OSD 언어 , 메뉴가 화면에 머무르 는 시간의 길이 등과 같은 OSD 설정을 조정합니다 . Language( 언어 ) 옵션을 사용하여 OSD 디스플레이 를 8 개 언어 ( 영어 , 스페인어 , 프랑스어 , 독일어 , 브 라질 포르투갈어 , 러시아어 , 중국어 간체 또는 일본 어 ) 가운데 하나로 설정할 수 있습니다 . Auto Rotation 모니터 Auto Rotation( 자동 회전 ) 을 On( 켜짐 ) 또 ( 자동 회전 ) 는 Off( 꺼짐 ) 으로 설정할 수 있습니다 . Transparency 이 옵션을 선택하면 및 버튼을 눌러 메뉴 투명 ( 투명도 ) 도를 변경할 수 있습니다 ( 최저 : 0 ~ 최고 : 100). Timer OSD Hold Time (OSD 유지 시간 ): 사용자가 마지막 ( 타이머 ) 으로 버튼을 누른 뒤 OSD 가 활성 상태에 머물러 있는 시간의 길이를 설정합니다 .
Lock( 잠금 ) 모니터에 있는 컨트롤 버튼을 잠궈서 사람들이 컨트 롤에 액세스하지 못하게 방지할 수 있습니다 . 또한 여 러 모니터를 나란히 설치한 경우 실수로 활성화하는 것을 방지할 수 있습니다 . • Menu Buttons( 메뉴 버튼 ): 모든 메뉴 / 기능 버튼 ( 전원 버튼 제외 ) 이 잠기고 사용자가 액세스할 수 없습니다 . • Power Button( 전원 버튼 ): 전원 버튼만 잠기고 사 용자가 액세스할 수 없습니다 . • Menu + Power Buttons( 메뉴 + 전원 버튼 ): 메뉴 / 기능 버튼과 전원 버튼이 둘다 잠기고 사용 자가 액세스할 수 없습니다 . • Color Custom Settings( 색 사용자 지정 설정 ): Color( 색 ) 메뉴 설정이 잠기고 사용자가 액세스할 수 없습니다 . 기본 설정은 Disable( 사용 안 함 ) 입니다 .
Personalize ( 개인 설정 ) Shortcut Key 1(바로 가기 키 1) Shortcut Key 2( 바로 가 기 키 2) Shortcut Key 3( 바로 가 기 키 3) Shortcut Key 4( 바로 가 기 키 4) Power Button LED( 전원 버튼 LED) USB-A Charging (USB-A 충전 ) Color Space( 색 공간 ), Luminance( 휘도 ), Input Source( 입력 소스 ), Aspect Ratio( 종횡비 ), Digital Cinema Masking( 디지털 시네마 마스킹 ), Markers ( 마커 ), PBP Mode(PBP 모드 ), PBP Input Source Toggle(PBP 입력 소스 토글 ), Video Swap( 비디오 스왑 ), Calibrate Now( 지금 보정 ), Show Last Calibration Results( 마지막 보정 결과 표시 ), Validation( 확인 ), Show Last Valid
USB-C 모니터 전원 꺼짐 모드 동안 Always On USB Type-C Charging Charging ( 항상 켜짐 USB Type-C 충전 ) 기능을 활 (USB-C 충전 ) 성화 또는 비활성화할 수 있습니다 . Fast Wakeup Fast Wakeup( 빠른 깨우기 ) 기능을 On( 켜짐 ) 또는 ( 빠른 깨우기 ) Off( 꺼짐 ) 으로 설정할 수 있습니다 . Warm Up Time 모니터 웜업을 켜거나 끌 수 있으며 , 예약된 Day before Use ( 날짜 ) 및 Time( 시간 ) 에 자동으로 활성화되도록 설 ( 사용 전 웜업 정할 수 있습니다 . 기본값은 Off( 꺼짐 ) 입니다 . 시간 ) Reset Personalize( 개인 설정 ) 메뉴 아래의 모든 설정을 공 Personalization 장 사전 설정값으로 초기화합니다 .
Set Date and 모니터의 날짜와 시간을 설정합니다 . Time( 날짜 및 참고 : 다음과 같은 때에 날짜와 시간을 동기화하십 시간 설정 ) 시오 : • 처음으로 모니터를 설정할 때 . • 모니터에 10 일 이상 전원 공급을 끊은 경우 . DDC/CI DDC/CI( 디스플레이 데이터 채널 / 명령 인터페이 스 ) 는 컴퓨터에 설치된 소프트웨어를 사용하여 모니 터 파라미터 ( 밝기 , 색상 , 밸런스 등 ) 를 조정할 수 있게 합니다 . Off( 꺼짐 ) 을 선택하여 이 기능을 비활성화할 수 있 습니다 . 이 기능을 사용 설정하면 모니터에 대한 최상의 사용 자 경험과 최적 성능을 얻을 수 있습니다 .
LCD Conditioning (LCD 조절 ) Firmware ( 펌웨어 ) Service Tag ( 서비스 태그 ) Reset Others ( 기타 재설정 ) Factory Reset ( 공장 초기화 ) 이 기능은 사소한 잔상을 줄입니다 . 잔상의 정도에 따 라 프로그램이 실행되는 데 약간의 시간이 걸릴 수 있 습니다 . On( 켜짐 ) 을 선택하여 이 기능을 활성화할 수 있습니다 . 모니터의 펌웨어 버전을 표시합니다 . 모니터의 서비스 태그 일련 번호를 표시합니다 . Others( 기타 ) 메뉴 아래의 모든 설정을 공장 사전 설 정값으로 초기화합니다 . 모든 설정을 공장 사전 설정값으로 초기화합니다 . 참고 : 다음 설정은 Factory Reset( 공장 초기화 ) 후 에 초기화되지 않습니다 : 보정 및 확인 데이터 , 언어 , 날짜와 시간 .
참고 : 연결된 입력 신호에 따라 메시지가 약간 다를 수 있습니다 . 이것은 모니터가 컴퓨터에서 수신 중인 신호와 동기화할 수 없음을 뜻합니다. 이 모니터가 처리할 수 있는 수평 및 수직 주파수 범위에 대해서는 모니터 규격을 참 조하십시오 . 권장 모드는 3840 x 2160 입니다 . DDC/CI 기능이 사용 해제되기 전에 다음 메시지가 표시됩니다 : 처음 Luminance( 휘도 ) 수준을 조정할 때 다음 메시지가 표시됩니다 : 참고 : Yes( 예 ) 를 선택한 경우 , 다음 번에 Luminance( 휘도 ) 설정을 변경 할 때는 이 메시지가 표시되지 않습니다 .
참고 : 위에서 언급한 기능 중 하나에 대해 Yes( 예 ) 를 선택한 경우 , 다음 번 에 이러한 기능 설정을 변경할 때는 이 메시지가 표시되지 않습니다 . 공장값 재설정을 수행하면 다시 메시지가 표시됩니다 . Lock( 잠금 ) 기능이 활성화되기 전에 다음 메시지가 표시됩니다 : 참고 : 선택된 설정에 따라 메시지가 약간 다를 수 있습니다 . 모니터가 대기 모드에 들어가면 다음 메시지가 표시됩니다 : OSD 를 이용하려면 컴퓨터를 켜서 모니터를 절전 모드에서 해제하십시오 . 참고 : 연결된 입력 신호에 따라 메시지가 약간 다를 수 있습니다 . 전원 버튼 이외의 아무 버튼이나 누르면 선택된 입력에 따라 다음 메시지가 표시 됩니다 : 참고 : 연결된 입력 신호에 따라 메시지가 약간 다를 수 있습니다 .
Thunderbolt, HDMI 또는 DP 입력 중에서 하나를 선택했고 해당 케이블을 연결 하지 않았다면 아래와 같이 이동하는 대화 상자가 나타납니다 . 참고 : 연결된 입력 신호에 따라 메시지가 약간 다를 수 있습니다 . 모니터가 DP/HDMI 입력 하에 있고 Thunderbolt™ 3 활성 케이블이 DP 교대 모드 를 지원하는 노트북에 연결되어 있을 때 , USB-C Charging (USB-C 충전 ) 이 활 성화되어 있으면 , 아래 메시지가 나타납니다 . Factory Reset( 공장 초기화 ) 가 선택되었을 때 아래 메시지가 나타납니다 .
Yes( 예 ) 가 선택되었을 때 아래 메시지가 나타납니다 . 자세한 내용은 문제 해결을 참조하십시오 . 최적 해상도 설정하기 모니터 최대 해상도 설정하기 : Windows® 7, Windows® 8 및 Windows® 8.1 에서 : 1. Windows® 8 및 Windows® 8.1 에서는 데스크톱 타일을 선택하여 고전적인 데스크톱으로 전환합니다 . 2. 바탕 화면을 오른쪽 클릭한 다음 화면 해상도를 선택합니다 . 3. 화면 해상도의 드롭다운 목록을 클릭하고 3840 x 2160 을 선택합니다 . 4. 확인을 클릭합니다 . Windows® 10 에서 : 1. 바탕 화면을 오른쪽 클릭한 다음 디스플레이 설정을 선택합니다 . 2. 고급 디스플레이 설정을 클릭합니다 . 3. 해상도의 드롭다운 목록을 클릭하고 3840 x 2160 을 선택합니다 . 4. 적용을 클릭합니다 . 3840 x 2160 옵션이 없는 경우 , 그래픽 드라이버가 4K@60 Hz 를 지원하는지 확 인해 봐야 합니다 .
Dell 컴퓨터 ( 휴대용 또는 데스크톱 ) 가 아닌 다른 컴퓨터를 사용하는 경우 : • 컴퓨터의 지원 사이트를 방문하여 최신 그래픽 드라이버를 다운로드하십 시오 . • 그래픽 카드 웹사이트를 방문하여 최신 그래픽 드라이버를 다운로드하십 시오 . Performing Color Calibration( 색 보정 수행 ) 내장된 비색계를 사용해 Calibration( 보정 ) 을 수행하여 모니터의 색상을 보정 합니다 . OSD 메뉴 사용 1. OSD 메뉴를 사용하여 선호도에 따라 보정 조건을 설정합니다 . 그런 다음 Calibrate Now( 지금 보정 ) 을 선택합니다 . 2. 다음 메시지가 표시되면 Yes( 예 ) 를 선택하여 작업을 계속합니다 .
3. 보정이 자동으로 시작됩니다 . 비디오 신호로 바로가기 사용 1. 기능 버튼을 눌러 바로가기 키를 표시합니다 . 2. 버튼을 누릅니다 . 3. 다음 메시지가 표시되면 Yes( 예 ) 를 선택하여 작업을 계속합니다 .
4. 보정이 자동으로 시작됩니다 . 비디오 신호 없이 바로가기 사용 컴퓨터에서 입력 신호를 얻지 않고 모니터에 대한 보정을 수행할 수 있습니다 . 1. 기능 버튼을 눌러 바로가기 키를 표시합니다 . 2. 버튼을 누릅니다 .
3. 보정이 자동으로 시작됩니다 . 참고 : 세로 모드에서의 Calibration( 보정 ) 은 권장되지 않습니다 . 참고 : 자세한 기능은 Calibration ( 보정 ) 를 참조하십시오 . 보정 작업 중지 아무 때나 보정 작업을 중지할 수 있습니다 . 1. 보정 작업 동안 기능 버튼을 누르면 다음 메시지가 표시됩니다 . 2. Yes( 예 ) 를 선택하여 작업을 중지합니다 .
색상 확인 수행 내장된 비색계를 사용해 색상 보정에 대한 Validation( 확인 ) 을 수행합니다 . OSD 메뉴 사용 1. OSD 메뉴를 사용하여 선호도에 따라 유효성 확인 조건을 설정합니다 . 그 런 다음 Validate Now( 지금 확인 ) 을 선택하여 확인 작업을 시작합니다 . 2. 다음 메시지가 표시되면 Yes( 예 ) 를 선택하여 작업을 계속합니다 .
3. 확인이 자동으로 시작됩니다 . 비디오 신호 없이 바로가기 사용 컴퓨터에서 입력 신호를 얻지 않고 모니터에 대한 확인을 수행할 수 있습니다 . 1. 기능 버튼을 눌러 바로가기 키를 표시합니다 . 2. 버튼을 누릅니다 .
3. 다음 메시지가 표시되면 Yes( 예 ) 를 선택하여 작업을 계속합니다 . 참고 : 세로 모드에서의 Validation( 확인 ) 은 권장되지 않습니다 . 참고 : 자세한 기능은 Validation ( 확인 ) 를 참조하십시오 . 확인 작업 중지 아무 때나 확인 작업을 중지할 수 있습니다 . 1. 확인 작업 동안 기능 버튼을 누르면 다음 메시지가 표시됩니다 . 2. Yes( 예 ) 를 선택하여 작업을 중지합니다 .
기울이기 , 좌우 회전 , 수직 확장 사용하기 참고 : 이것은 스탠드 장착형 모니터에 적용될 수 있습니다 . 기타 스탠드를 구입할 때 , 스탠드 설치 안내서에 포함된 설치 지침을 참조하십시오 . 기울이기 , 좌우 회전 모니터에 장착된 스탠드를 사용할 때 보기에 가장 알맞은 각도로 모니터를 기울 이거나 회전할 수 있습니다 . 참고 : 스탠드는 모니터에서 분리되어 출고됩니다 .
수직 확장 참고 : 스탠드 높이를 최대 130 mm 높일 수 있습니다 . 아래 그림들은 스탠드 높이를 높이는 방법을 보여줍니다 . 모니터 회전시키기 모니터를 회전시키기 전에 모니터를 완전히 수직으로 확장 ( 수직 확장 ) 시키 거나 완전히 기울여야만 모니터의 하단 가장자리가 부딪치는 것을 피할 수 있습 니다 .
시계 방향으로 회전 반시계 방향으로 회전 74 │ 모니터 조작
문제 해결 경고 : 이 단원에 있는 절차를 시작하기 전에 안전 지침을 따르십시오 . 자가 검사 사용자는 이 모니터의 자가 시험 기능을 이용하여 모니터가 제대로 동작하는지 점검할 수 있습니다 . 모니터와 컴퓨터가 제대로 연결되어 있는데도 모니터 화면 이 켜지지 않으면 다음 단계를 수행하여 모니터 자가 검사를 실행합니다 : 1. 컴퓨터와 모니터를 모두 끕니다 . 2. 컴퓨터의 후면에서 비디오 케이블을 뽑습니다 . 3. 모니터를 켭니다 . 모니터가 정상적으로 동작하면서도 비디오 신호를 감지할 수 없는 경우 움직이 는 대화 상자가 화면 ( 흑색 배경 ) 에 표시됩니다 . 자가 검사 모드에서는 전원 LED 가 흰색으로 켜져 있습니다 . 또한 , 선택한 입력에 따라 아래의 대화상자가 화면을 계속 스크롤합니다 . 참고 : 연결된 입력 신호에 따라 메시지가 약간 다를 수 있습니다 . 4. 비디오 케이블의 연결이 해제되거나 손상된 경우 정상적인 시스템 작동 중 에도 이 상자가 나타납니다 . 5.
내장형 진단 도구 모니터에 내장된 진단 도구는 화면 비정상이 모니터의 고유한 문제인지 아니면 컴퓨터와 비디오 카드의 문제인지 판단하는 데 도움을 줍니다 . 참고 : 비디오 케이블이 뽑혀 있고 모니터가 자가 검사 모드에 있을 때만 내장 된 진단 도구를 실행할 수 있습니다 . 내장된 진단 도구 실행하기 : 1. 화면이 깨끗한지 확인합니다 ( 화면 표면에 먼지 입자가 없는지 확인 ). 2. 컴퓨터 또는 모니터의 후면에서 비디오 케이블을 뽑습니다 . 그러면 모니터 가 자가 검사 모드에 들어갑니다 . 3.
4. 버튼을 눌러 진단 아이콘을 강조 표시한 다음 버튼을 누르면 회색 화면이 표시됩니다 . 5. 화면의 비정상 여부를 주의하여 검사합니다 . 6. 전면 패널의 버튼 1 을 다시 누릅니다 . 화면 색상이 적색으로 변합니다 . 7. 디스플레이의 비정상 여부를 검사합니다 . 8. 녹색 , 청색 , 검정 , 백색 , 텍스트 화면에서 6 단계와 7 단계를 반복하여 디 스플레이를 검사합니다 . 텍스트 화면이 표시되면 검사가 완료됩니다 . 종료하려면 버튼 1 을 다시 누릅 니다 . 내장된 진단 도구를 사용하여 실시한 검사에서 화면 비정상이 감지되지 않을 경 우 , 모니터는 제대로 동작하고 있는 것입니다 . 비디오 카드와 컴퓨터를 점검합 니다 . 항상 켜짐 USB Type-C (Thunderbolt™) 충전 모니터 전원이 꺼졌을 때도 Thunderbolt™ 3 활성 케이블을 통해 노트북 또는 모바일 장치를 충전할 수 있습니다 .
일반적 문제 다음 표에는 일반적인 모니터 문제에 관한 일반 정보와 사용 가능한 해결책이 나 와 있습니다 : 일반 증상 문제 비디오 없음 / 전원 LED 꺼짐 영상 없음 가능한 해결책 • 모니터와 컴퓨터를 연결하는 비디오 케이블 이 올바르게 단단히 연결되어 있는지 확인합 니다 . • 다른 전기 장비를 사용하여 전원 콘세트가 올바르게 작동하고 있는지 확인합니다 . • 전원 버튼을 완전히 눌렀는지 확인합니다 . • Input Source ( 입력 소스 ) 메뉴에서 올 바른 입력 소스가 선택되었는지 확인하십 시오 . 비디오 없음 / 전원 LED 켜짐짐 영상이 없거나 어두움 • OSD 를 사용하여 밝기와 명암 대비를 증가 시킵니다 . • 모니터 자가 검사 기능 점검을 수행합니다 . • 비디오 케이블 커넥터의 핀이 구부러지거나 부러졌는지 확인합니다 . • 내장된 진단 도구를 실행합니다 . • Input Source ( 입력 소스 ) 메뉴에서 올 바른 입력 소스가 선택되었는지 확인하십 시오 .
픽셀 손실 LCD 화면에 점 • 전원을 껐다가 다시 켭니다 . 이 있음 • 영구적으로 꺼져 있는 픽셀은 LCD 기술에서 발생할 수 있는 자연적인 결함입니다 . • Dell 모니터 품질 및 픽셀 정책에 대해서는 Dell 지원 사이트를 참조하십시오 : http://www.dell.com/support/monitors. 고정된 픽셀 LCD 화면에 밝 • 전원을 껐다가 다시 켭니다 . 은 점이 있음 • 영구적으로 꺼져 있는 픽셀은 LCD 기술에서 발생할 수 있는 자연적인 결함입니다 . • Dell 모니터 품질 및 픽셀 정책에 대해서는 Dell 지원 사이트를 참조하십시오 : http://www.dell.com/support/monitors. 밝기 문제 영상이 너무 어둡거나 너무 밝음 • 모니터를 공장 설정으로 초기화합니다 . • OSD 를 사용하여 밝기와 명암 대비를 조정 합니다 . 기하학적인 왜곡 화면이 정확하 • 모니터를 공장 설정으로 초기화합니다 .
간헐적 문제 모니터 켜짐 및 꺼짐 오 작동 • 모니터와 컴퓨터를 연결하는 비디오 케이블 이 올바르게 단단히 연결되어 있는지 확인합 니다 . • 모니터를 공장 설정으로 초기화합니다 . • 모니터 자가 검사 기능 점검을 수행하고 자 가 검사 모드에서도 간헐적 문제가 발생하는 지 확인합니다 . 색 손실 영상 색 손실 • 모니터 자가 검사 기능 점검을 수행합니다 . • 모니터와 컴퓨터를 연결하는 비디오 케이블 이 올바르게 단단히 연결되어 있는지 확인합 니다 . • 비디오 케이블 커넥터의 핀이 구부러지거나 부러졌는지 확인합니다 . 색상 오류 영상 색상 불량 • 응용 프로그램에 따라 Color( 색 ) 메뉴 OSD 에서 Preset Modes( 사전 설정 모드 ) 의 설 정을 변경합니다 . • Color( 색 ) 메뉴 OSD 의 Custom Color( 사 용자 지정 색상 ) 아래서 R/G/B 값을 조정합 니다 .
제품 고유의 문제 고유의 증상 화면 이미지가 너무 작음 문제 이미지가 화면 중앙에 있지만 전체 시청 영역 을 채우지 않음 화면에 OSD 가 전면 패널의 버튼으로 모니 나타나지 않음 터를 조정할 수 없음 사용자 조절 버튼을 눌러도 입력 신호가 없음 가능한 해결책 • Display( 디스플레이 ) 메뉴 OSD 에서 Aspect Ratio( 화면비 ) 설정을 확인합 니다 . • 모니터를 공장 설정으로 초기화합니다 . • 모니터를 끄고 전원 코드를 뽑았다가 다 시 꽂고 모니터를 켭니다 . • OSD 메뉴가 잠겨 있는지 확인하십시오 . 잠겨 있으면 전원 버튼 옆에 있는 메뉴 / 기능 버튼을 4 초 동안 누릅니다 ( 자세한 내용은 Lock( 잠금 ) 참조 ). 사진이 없을 때 • 신호 소스를 점검합니다 . 마우스를 움직 이거나 키보드의 아무 키나 눌러 컴퓨터 LED 빛이 흰색임 가 절전 모드에 있지 않은지 확인합니다 . • 신호 케이블이 제대로 연결되었는지 확 인합니다 .
HDMI 포트에 비디오 없음 HDMI 포트에서 일부 도킹 장치 에 연결된 경우 , 노트북에서 Thunderbolt™ 케이블을 연결 해제 / 연결할 때 비디오가 없습 니다 . • 도킹 장치에서 HDMI 케이블을 뺀 다음 , 도킹 Thunderbolt™ 케이블을 노트북에 연결하십시오 . 7 초 후에 HDMI 케이블 을 연결하십시오 . 범용 직렬 버스 (USB) 관련 문제 고유의 증상 USB 인터페이 스가 작동하지 않습니다 문제 가능한 해결책 USB 주변 장치 • Thunderbolt™ 3 활성 케이블을 연결 해제 / 연결합니다 . 가 작동하지 않 습니다 • 모니터 전원이 켜져 있는지 확인합니다 . • Thunderbolt™ 3 활성 케이블을 컴퓨터에 다시 연결합니다 . • USB 주변 장치 ( 다운스트림 커넥터 ) 를 다시 연결합니다 . • 모니터 전원을 껐다가 다시 켭니다 . • 컴퓨터를 다시 부팅합니다 .
Thunderbolt™ 3 이미지가 표시 연결을 사용할 되지 않음 때 DC 켜기 / 끄 기 후 , 대기 모 드에서 나올 때 비디오 없음 • Thunderbolt™ 3 활성 케이블을 연결 해제 / 연결합니다 . • 연결된 장치가 Thunderbolt™ 3 사양과 호 환되는지 확인합니다 . • Thunderbolt™ 3 활성 케이블이 컴퓨터로 부터 모니터의 USB-C 업스트림 포트에 연결되었는지 확인합니다 . • 모니터에 포함되어 있는 Thunderbolt™ 3 활성 케이블을 사용합니다 . • Windows 에서 , Windows 시스템 트레이 ( 화면 오른쪽 아래 구석에 있음 ) 에 있는 Thunderbolt™ 로고를 클릭합니다 . Approve Thunderbolt Devices (Thunderbolt 장치 승인 ) 아래에서 이 모 니터에 대해 “Always Connect”( 항상 연 결 ) 을 선택합니다 .
무선 마우스가 작동하지 않거 나지체됨 반응을 하지 않 • USB 주변 장치와 무선 USB 수신기 사이 의 거리를 늘리십시오 . 거나 느리게 반 응함 • 무선 USB 수신기를 무선 마우스와 가능 한 가깝게 놓습니다 . • USB 연장 케이블을 사용하여 무선 USB 수신기를 USB 3.2 포트에서 가능한 멀리 놓습니다 .
부록 경고 : 안전 지침 경고 : 본 안내서에서 설명된 것과 다르게 컨트롤 , 조정 또는 절차를 사용하 면 감전 , 전기적 위험 및 / 또는 기계적 위험에 노출될 수 있습니다 . 안전 지침에 대한 정보는 안전 , 환경 및 규제 정보 (SERI) 를 참조하십시오 . FCC 고지 ( 미국에만 해당 ) FCC 통지 및 기타 규정 정보는 www.dell.com/regulatory_compliance 에 있는 규 정 준수 웹사이트를 참조하십시오 . Dell 에 연락 미국 내 고객은 800-WWW-DELL(800-999-3355) 로 전화하십시오 . 참고 : 활성 인터넷 연결이 없으면 구매 인보이스 , 포장 명세서 , 청구서 또는 Dell 제품 카탈로그에서 연락처 정보를 찾을 수 있습니다 . Dell 은 몇몇 온라인 및 전화 기반 지원과 서비스 옵션을 제공합니다 . 이용 가능 성은 나라와 제품에 따라 다르며 , 사용자의 지역에선 일부 서비스를 이용하지 못할 수도 있습니다 . • 온라인 기술 지원 ─ www.
USB-C 에서 비디오 및 USB 지원 USB-C 를 통해 모니터에 연결했을 때 비디오 해상도 및 USB 지원 . 비디오 USB TBT3 다운 USB-A 다 스트림에 운스트림 연결된 에 연결된 USB-C 장 USB 장치 치 ( 모니 ( 모니터 포 터 포트 트 7-1 ~ 6-2) 7-4) 호스트 컴퓨터에 서 연결 사용된 업스트 림 케이블 ( 호 스트 컴퓨터 모니터 포트 6-1) 4K ( 직접 연결 ) 4K ( 데이지 체인 ) TBT3 다 운스트림 에 연결된 TBT3 장 치 ( 모니 터 포트 6-2) USB-A USB A - C* 아니오 아니오 아니오 USB2.0 USB2.0/ 3.2 USB-C MFDP 아니오 아니오 아니오 USB2.0 USB2.0/ 3.2 TBT3 패시브 아니오 아니오 아니오 USB2.0 USB2.0/ 3.2 TBT3 액티브 * USB-C MFDP 아니오 아니오 USB2.0 USB2.0 USB2.0 예 아니오 아니오 USB2.
Thunderbolt™ 3 패시브 케이블 구매 지역 링크 https://www.dell.com/en-us/shop/accessories/apd/a9905599 Dell 웹사 https://www.dell.com/en-us/shop/accessories/apd/a9905597 이트 https://www.dell.com/en-us/shop/accessories/apd/a9269731 미국 https://www.belkin.com/us/p/P-F2CD081/ https://www.delock.com/produkte/G_84846/merkmale.html/ EMEA https://www.hama.cz/hama-kabel-thunderbolt-3-usb-c-typ-cvidlice--vidlice-20-gb-s-100-w-1-m/ https://www.lindy-international.com/Thunderbolt-3-Cable2m.htm?websale8=ld0101.