Dell UltraSharp 27 4K PremierColor monitor—UP2720Q Uputstvo za korišćenje Model: UP2720Q Regulatorni model: UP2720Qb
Napomene, mere opreza i upozorenja NAPOMENA: NAPOMENA označava važne informacije koje vam pomažu da na bolji način iskoristite svoj računar. OPREZ: OPREZ označava potencijalno oštećenje hardvera ili gubitak podataka ukoliko se uputstva ne prate. UPOZORENJE: UPOZORENJE označava mogućnost za oštećenje imovine, telesnu povredu ili smrt. Copyright © 2019 - 2020 Dell Inc. Sva prava zadržana. Ovaj proizvod je zaštićen SAD i međunarodnim zakonima o zaštiti autorskog prava i intelektualne svojine.
Sadržaj O vašem monitoru . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Sadržaj pakovanja. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Karakteristike proizvoda . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Identifikacija delova i kontrola . . . . . . . . . . . . . . . . . . . . . 10 Prednja strana. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Zadnja strana . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Podešavanje monitora . . . . . . . . . . . . . . . . . . . . . . .27 Pričvršćivanje stalka . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Pričvršćivanje haube monitora . . . . . . . . . . . . . . . . . . . . . 30 Povezivanje vašeg monitora . . . . . . . . . . . . . . . . . . . . . . . 31 Povezivanje HDMI kabla. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Povezivanje DisplayPort (DP na DP) kabla . . . . . . . . . . . . . . . . . .
Korišćenje naginjanja, okretanja i vertikalnog proširenja . 76 Naginjanje i okretanje . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Vertikalno proširenje. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Rotiranje monitora . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Rešavanje problema . . . . . . . . . . . . . . . . . . . . . . . . 79 Samotestiranje . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
O vašem monitoru Sadržaj pakovanja Vaš monitor se isporučuje sa komponentama prikazanim u nastavku. Proverite da li ste primili sve komponente i Kontaktirajte Dell ukoliko nešto nedostaje. NAPOMENA: Neke stavke mogu biti opcionalne i možda se ne isporučuju uz vaš monitor. Neke funkcije ili mediji možda neće biti dostupni u određenim zemljama. NAPOMENA: Da biste ga podesili sa bilo kojim drugim stalkom, potražite uputstva za podešavanje u odgovarajućem uputstvu za podešavanje stalka.
Postolje stalka Hauba monitora Kabl za napajanje (varira u zavisnosti od zemlje) HDMI kabl DP kabl (DP na DP) Thunderbolt™ 3 (USB tip C) aktivan kabl O vašem monitoru │ 7
USB kabl tipa C na tip A • Izveštaj o fabričkoj kalibraciji • Tehnički podaci za kalibraciju i validaciju • Vodič za brzo podešavanje • Bezbednosne, regulativne i informacije o zaštiti životne sredine 8 │ O vašem monitoru
Karakteristike proizvoda Dell Dell UP2720Q monitor sa ravnim ekranom karakteriše tehnologija aktivne matrice, tankoslojnih tranzistora (TFT), displeja sa tečnim kristalima (LCD). Karakteristike monitora uključuju: • Oblast prikaza od 68,47 cm (27 inča) (po dijagonali). Rezolucija od 3840 x 2160 (16:9), sa podrškom preko celog ekrana za manje rezolucije. • Širok ugao gledanja koji omogućava gledanje iz sedećeg ili stajaćeg položaja.
Identifikacija delova i kontrola Prednja strana Kontrole na prednjoj ploči Oznaka Opis 1 Funkcijski tasteri (za više informacija, pogledajte .
Zadnja strana Zadnja strana sa i bez stalka monitora Oznaka Opis Upotreba 1 VESA montažni otvori (100 mm x 100 mm - iza pričvršćenog VESA poklopca) Zidna montaža monitora korišćenjem kompleta za zidnu montažu koji je kompatibilan sa VESA (100 mm x 100 mm). 2 Regulatorna nalepnica Navodi regulatorna odobrenja. 3 Dugme za oslobađanje stalka Oslobađa stalak od monitora.
Donja strana Donja strana bez stalka monitora Oznaka Opis Upotreba 1 Konektor za AC napajanje Povežite kabl za napajanje (isporučuje se sa monitorom). 2 Otvor za bezbednosno zaključavanje Osigurava monitor bezbednosnim zaključavanjem (bezbednosno zaključavanje nije uključeno). 3 (1, 2) Konektor za HDMI port Povežite svoj računar HDMI kablom. 4 Konektor za Povežite svoj računar DP kablom. DisplayPort ulaz 5 Linijski audio izlaz Povežite svoje zvučnike.
Thunderbolt™ 3 podržava monitor sa opcijom MST (prenos više kanala). Za omogućavanje MST-a, pogledajte uputstvo u odeljku “Povezivanje monitora za funkciju Thunderbolt™ prenosa više kanala (MST)”. NAPOMENA: Thunderbolt™ 3 nije podržan na verzijama operativnog sistema Windows pre verzije Windows 10. 6-2 Thunderbolt™ 3 port za otpremanje (USB tip C) Povežite Thunderbolt™ 3 aktivan kabl, koji je isporučen uz monitor, sa računarom, mobilnim uređajima, drugim monitorom ili drugim Thunderbolt™ uređajima.
8 Funkcija zaključavanja stalka Za zaključavanje stalka za monitor korišćenjem M3 x 6 mm zavrtnja (zavrtanj nije uključen). * Korišćenje slušalica nije podržano za konektor linijskog audio izlaza. ** Da biste izbegli smetnje signala kada je bežični USB uređaj povezan na USB port za preuzimanje, NE preporučuje se da povezujete bilo koji drugi USB uređaj na susedni port/susedne portove.
Vreme odziva • 6 ms sivo na sivom u Fast (Brzo) režimu • 8 ms sivo na sivom u Normal (Normalno) režimu • 14 ms sivo na sivom u Off (Isključeno) režim Dubina boja 1,07 miliona boja (realnih 10 bitova) Opseg boja CIE1931 Adobe 100% CIE1976 DCI-P3 98% CIE1976 BT.2020 80% Preciznost kalibracije Delta E < 2 (prosečna) NAPOMENA: Samo za CIE1931 Adobe 100% i CIE1976 DCI-P3 98%. Povezivanje • 1 x DP 1.4 (HDCP 2.2) • 2 x HDMI 2.0 (HDCP 2.2) • 1 x Thunderbolt™ 3 port za otpremanje (DP1.
Specifikacije rezolucije Model UP2720Q Opseg horizontalnog skeniranja 15 kHz do 135 kHz (automatski) (HDMI & DP & Thunderbolt™ 3 alternativni režim) Opseg vertikalnog skeniranja (HDMI & DP & Thunderbolt™ 3 alternativni režim) 23 Hz do 86 Hz (automatski) Maksimalna unapred određena rezolucija 3840 x 2160 na 60 Hz Podržani režimi video zapisa Model UP2720Q Mogućnosti prikazivanja video zapisa (HDMI reprodukcija) 480p, 576p, 720p, 1080i, 1080p, QHD, UHD (Režim preplitanja nije podržan u PBP režimu)
VESA, 1920 x 1080 67,5 60,0 148,5 +/+ VESA, 2048 x 1280 - R 78,9 59,9 174,3 +/- VESA, 2048 x 1440 - R 88,8 60,0 241,5 +/- VESA, 3840 x 2160* 133,3 60,0 533,3 +/- VESA, 3840 x 2160** 135 60,0 594 +/- 2560 x 1440 88,787 59,951 241,55 +/- 2048 x 1080 27,0 24,0 74,25 +/- 2048 x 1080 54,0 48,0 148,5 +/- * Zahteva grafičku karticu koja podržava DP. ** Zahteva grafičku karticu koja podržava HDMI 2.0.
Električne specifikacije Model UP2720Q Ulazni video signali HDMI 2.0*/DP 1.4, 600 mV za svaku diferencijalnu liniju, ulazna impedansa od 100 ohm po diferencijalnom paru. AC ulazni napon/ frekvencija/struja 100 VAC to 240 VAC / 50 Hz ili 60 Hz + 3 Hz / 2,8 A (tipično) Vršna indukovana struja • 120 V: 40 A (maks.) pri 0°C (hladan start) • 240 V: 80 A (maks.) pri 0°C (hladan start) Potrošnja struje • 0,2 W (režim Isključeno)1 • 0,2 W (režim pripravnosti)1 • 32,0 W (režim Uključeno)1 • 230 W (maks.
Fizičke karakteristike Model UP2720Q Tip konektora • 1 x DP 1.4 • 2 x HDMI 2.0 • 1 x Thunderbolt™ 3 port za otpremanje (DP1.4) • 1 x Thunderbolt™ 3 port za preuzimanje (DP1.4) • 2 x USB 3.2 Gen2 portova za preuzimanje • 2 x USB 3.2 Gen1 portova za preuzimanje (1 x BC1.2 sa opcijom punjenja sa 2 A (maks.
Fizičke karakteristike (nastavak) Dimenzije stalka Visina (produžen) 456,3 mm (17,96 in) Visina (skraćen) 408,9 mm (16,10 in) Širina 260,0 mm (10,24 in) Dubina 212,0 mm (8,35 in) Težina Težina sa ambalažom 14,14 kg (31,17 lb) Težina sa sklopom stalka i kablovima 9,71 kg (21,41 lb) Težina bez sklopa stalka (za opciju zidne montaže ili VESA montaže - bez kablova) 5,55 kg (12,24 lb) Težina sklopa stalka 3,64 kg (8,02 lb) Odsjaj prednjeg okvira 2-4 Ekološke karakteristike Model UP2720Q Uskla
Ekološke karakteristike (nastavak) Visina Radna 3.048 m (10.000 ft) (maksimalno) Ne-radna 12.192 m (40.
18 Detekcija priključivanja pod naponom 19 Re-PWR 20 +3,3 V DP_PWR HDMI konektor Broj pina 19-pinska strana povezanog signalnog kabla 1 TMDS DATA 2+ 2 TMDS DATA 2 SHIELD 3 TMDS DATA 2- 4 TMDS DATA 1+ 5 TMDS DATA 1 SHIELD 6 TMDS DATA 1- 7 TMDS DATA 0+ 8 TMDS DATA 0 SHIELD 9 TMDS DATA 0- 10 TMDS CLOCK+ 11 TMDS CLOCK SHIELD 12 TMDS CLOCK- 13 CEC 14 Rezervisano (nije povezan na uređaju) 15 DDC CLOCK (SCL) 16 DDC DATA (SDA) 17 DDC/CEC uzemljenje 18 +5 V NAPAJANJE 19
Plug and Play mogućnost Možete da instalirate monitor u bilo kom sistemu koji je kompatibilan sa Plug and Play mogućnošću. Monitor automatski obezbeđuje računarskom sistemu svoj EDID (Extended Display Identification Data) korišćenjem protokola kanala za prikaz podataka (DDC) tako da sistem može sam da se konfiguriše i optimizuje podešavanja monitora. Većina instalacija monitora je automatska; možete izabrati različita podešavanja po želji.
USB konektor za preuzimanje Broj pina 9-pinska strana konektora 1 VCC 2 D- 3 D+ 4 GND 5 SSRX- 6 SSRX+ 7 GND 8 SSTX- 9 SSTX+ Thunderbolt™ 3 konektor Broj pina Naziv signala Broj pina Naziv signala A1 GND B1 Detekcija kabla A2 TX1+ B2 TX2+ A3 TX1- B3 TX2- A4 VBUS B4 VBUS A5 CC1 B5 CC2 A6 D+ B6 D+ A7 D- B7 D- A8 SBU1 B8 SBU2 A9 VBUS B9 VBUS 24 │ O vašem monitoru
A10 RX2- B10 RX1- A11 RX2+ B11 RX1+ A12 GND B12 GND USB portovi • 1 x Thunderbolt™ 3 port za preuzimanje (kompatibilan sa USB tip C) - donji • 1 x Thunderbolt™ 3 port za otpremanje (kompatibilan sa USB tip C) - donji • 2 x USB 3.2 Gen preuzimanje - donji • 2 x USB 3.2 Gen1 preuzimanje - donji • Port za punjenje - port sa ikonom baterije ; podržava mogućnost punjenja brzom strujom ukoliko je uređaj kompatibilan sa BC1.2. NAPOMENA: USB 3.2 funkcionalnost zahteva računar komaptibilan sa USB 3.2.
Smernice za održavanje Čišćenje vašeg monitora OPREZ: Pročitajte i pratite Bezbednosna uputstva pre čišćenja monitora. UPOZORENJE: Pre čišćenja monitora, izvucite kabl za napajanje monitora iz električne utičnice. Za najbolje prakse, pratite uputstva na listi u nastavku dok raspakujete, čistite ili rukujete svojim monitorom: • Da biste očistili svoj antistatički ekran, lagano navlažite meku, čistu krpu vodom.
Podešavanje monitora Pričvršćivanje stalka NAPOMENA: Stalak je odvojen kada se monitor isporuči iz fabrike. NAPOMENA: Ovo je primenljivo za monitor sa stalkom. Kada se kupi bilo koji drugi stalak, potražite uputstva za podešavanje u odgovarajućem uputstvu za podešavanje stalka. OPREZ: Monitor nemojte vaditi iz pakovanja pre pričvršćivanja stalka. Za pričvršćivanje stalka monitora: 1. Pratite uputstva na kartonskim preklopima za skidanje stalka sa gornjeg jastučića koji ga učvršćava. 2.
5. Podignite poklopac, kao što je prikazano, da biste VESA područje izložili sklopu stalka. 6. Pričvrstite sklop stalka na monitor. a. Postavite dva kraka u gornjem delu stalka na žleb na poleđini monitora. b. Pritisnite stalak nadole dok se ne uglavi na mesto.
7. Uspravite monitor. NAPOMENA: Pažljivo podignite monitor da biste sprečili da isklizne ili padne. OPREZ: Nemojte da držite ili da podižete monitor držeći fioku kalorimetra tokom pomeranja monitora. 8. Skinite poklopac sa monitora.
Pričvršćivanje haube monitora Montaža haube monitora: 1. Izvadite haubu koja je isporučena uz monitor. 2. Rasklopite haubu tak oda „U“ kanalne trake na oba preklopa budu okrenute nagore.
3. Poravnajte stranu monitora kod „U“ kanalnih traka. 4. Gurnite poklopac do kraja nadole. Povezivanje vašeg monitora UPOZORENJE: Pre nego što započnete procedure u ovom odeljku, pratite Bezbednosna uputstva. NAPOMENA: Nemojte povezivati sve kablove na računar istovremeno. Da biste povezali monitor na računar: 1. Isključite računar i odvojite kabl za napajanje. 2. Povežite HDMI/DP/Thunderbolt™ 3 Aktivan kabl sa monitora na računar ili uređaj.
Povezivanje HDMI kabla NAPOMENA: Podrazumevano fabričko podešavanje na UP2720Q je HDMI 2.0. Ako monitor ne uspeva da prikaže bilo kakav sadržaj nakon što se poveže HDMI kabl, pratite procedure u nastavku da biste promenili podešavanja sa HDMI 2.0 na HDMI 1.4: • Pritisnite drugo dugme pored dugmeta • Koristite dugmad i zatim upotrebite dugme • Koristite dugmad i • Pritisnite i zadržite dugme da biste aktivirali OSD meni. da označite Input Source (Ulazni izvor), da uđete u podmeni.
Povezivanje DisplayPort (DP na DP) kabla NAPOMENA: Podrazumevano fabričko podešavanje na UP2720Q je DP 1.4. Povezivanje Thunderbolt™ 3 Aktivnog kabla NAPOMENA: Koristite samo Thunderbolt™ 3 Aktivan kabl koji je isporučen uz monitor. • • • • Ovaj port podržava samo alternativni režim za DP1.4. Thunderbolt™ 3 koji podržava napajanje (PD Verzija 3.0) snabdeva napajanjem do 90 W.
Povezivanje monitora za funkciju Thunderbolt™ prenosa više kanala (MST) NAPOMENA: UP2720Q podržava Thunderbolt™ MST funkciju. Da biste koristili ovu opciju, vaš računar mora da podržava Thunderbolt™ opciju. Podrazumevano fabričko podešavanje u UP2720Q je alternativni režim DP1.4. Za podešavanje MST veze, koristite samo Thunderbolt™ 3 aktivan kabl koji je isporučen uz monitor i obavite sledeće korake: 1. Isključite računar i odvojite kabl za napajanje. 2.
NAPOMENA: Ako koristite računar sa USB-C DP priključkom, posebno kupite USB-C DP kabl. Za više informacija, idite na: http://www.dell.com. NAPOMENA: Za informacije o kupovini Thunderbolt™ 3 pasivnog kabla, idite na: Kupovina Thunderbolt™ 3 pasivnog kabla.
OPREZ: Grafika se koristi samo u svrhe ilustracije. Izgled računara može da se razlikuje. Organizovanje kablova Nakon priključivanja svih neophodnih kablova na monitor i računar, (pogledajte Povezivanje vašeg monitora za priključivanje kablova,) organizujte sve kablove na već prikazan način.
Uklanjanje stalka monitora NAPOMENA: Da biste sprečili ogrebotine i oštećenja na zakrivljenom LCD ekranu tokom uklanjanja stalka, obavezno postavite monitor na mek, čisti penasti materijal. Direktan kontakt sa tvrdim predmetima može da izazove oštećenja zakrivljenog monitora. NAPOMENA: Ovo je primenljivo za monitor sa stalkom. Kada se kupi bilo koji drugi stalak, potražite uputstva za podešavanje u odgovarajućem uputstvu za podešavanje stalka. Za uklanjanje stalka: 1.
Zidna montaža (opcionalno) (Dimenzije zavrtnja: M4 x 10 mm). Pogledajte uputstvo koje se isporučuje uz komplet za zidnu montažu kompatibilan sa VESA. 1. Stavite panel monitora na meku krpu ili jastuk na stabilnom, ravnom stolu. 2. Skinite stalak. 3. Koristite Phillips krstasti odvijač za uklanjanje četiri zavrtnja koja učvršćuju plastični poklopac. 4. Pričvrstite montažni nosač iz kompleta za zidnu montažu na monitor. 5.
Rukovanje monitorom Uključivanje monitora Pritisnite dugme da uključite monitor. Korišćenje kontrola na prednjoj ploči Koristite kontrolnu dugmad sa prednje strane monitora za podešavanje postavki. Sledeća tabela opisuje dugmad na prednjoj ploči: Dugme na prednjoj ploči Opis Koristite ovo dugme da biste izabrali sa liste unapred određenih režima boje.
Koristite ovo dugme da izaberete ulazni izvor. 2 Taster prečice/ Input Source (Ulazni izvor) Koristite ovo dugme za pokretanje sekvence kalibracije boja. 3 Taster prečice/ Calibrate Now (Kalibriši sada) Koristite ovo dugme za prikaz trenutnih podešavanja monitora. 4 Taster prečice/ Display Info (Prikaz informacija) 5 Meni 6 Koristite dugme MENI da biste pokrenuli prikaz na ekranu (OSD). Pogledajte Pristupanje meniju sistema. Koristite ovo dugme za izlazak iz glavnog OSD menija.
Dugme na prednjoj ploči Koristite ovu dugmad sa prednje strane monitora za podešavanje postavki slike. Dugme na prednjoj ploči 1, 2 Ne funkcioniše 3 Opis Ova dugmad nemaju funkcije. Koristite dugme Gore da biste podesili (povećali opsege) stavke u OSD meniju. Gore 4 Koristite dugme Dole da biste podesili (smanjili opsege) stavke u OSD meniju. Dole Koristite dugme Unesi da uđete u podmeni. 5 Unesi 6 Koristite ovo dugme za izlazak iz glavnog OSD menija.
Korišćenje menija prikaza na ekranu (OSD) Pristupanje meniju sistema NAPOMENA: Ukoliko promenite podešavanja, a zatim ili nastavite do drugog menija ili izađete iz OSD menija, monitor automatski čuva te izmene. Izmene se takođe čuvaju ukoliko promenite podešavanja, a zatim sačekate da OSD meni nestane. 1. Pritisnite dugme za pokretanje OSD menija i prikažite glavni meni. 2. Pritisnite dugmad i za prebacivanje između opcija podešavanja. Dok prelazite sa jedne ikone na drugu, naziv opcije se označava.
Ikona Meni i podmeniji Color (Boja) Opis Koristite Color (Boja) da biste podesili režim podešavanja boje. Color Space Kada izaberete Color Space (Prostor boje), možete (Prostor boje) da izaberete nešto od sledećeg: DCI P3 D65 G2.4 L100, BT.709 D65 BT1886 L100, BT.2020 D65 BT1886 L100, sRGB D65 sRGB L250, Adobe RGB D65 G2.2 L250, Adobe RGB D50 G2.2 L250, Native (Prirodno), Custom 1 (Prilagođeno 1), Custom 2 (Prilagođeno 2), Custom 3 (Prilagođeno 3), CAL 1 ili CAL 2.
NAPOMENA: Factory Reset (Fabričko resetovanje) neće ukloniti kalibrisane podatke. Korisnik može da pređe na Color (Boja) > Color Space (Prostor boja) > Reset this Color Space # (Resetuj ovaj prostor boje #) (1~6) da ručno ukloni izabrane kalibracione podatke. Kalibracioni podaci za CAL 1 i CAL 2 se ne mogu ukloniti iz OSD-a. Reset Color Resetujte podešavanja boje vašeg monitora na fabrička (Resetuj boju) podešavanja.
Input Source Koristite meni Input Source (Ulazni izvor) da biste (Ulazni izvor) izabrali različite video signale koji mogu biti povezani na vaš monitor. Thunderbolt Izaberite Thunderbolt ulaz kada koristite Thunderbolt™ 3 konektor. Pritisnite dugme izaberete Thunderbolt ulazni izvor. DP Izaberite DP ulaz kada koristite DisplayPort (DP) konektor. Pritisnite dugme izvor. HDMI 1 da izaberete HDMI 1 ulazni izvor. Izaberite HDMI 2 ulaz kada koristite HDMI 2 konektor.
Auto Select for Thunderbolt (Automatski izbor za Thunderbolt) Omogućava vam da podesite Auto Select for Thunderbolt (Automatski izbor za Thunderbolt) za: • Prompt for Multiple Inputs (Pitanje za više ulaza): Uvek prikazuje poruku „Switch to Thunderbolt Video Input“ (Prebacite na Thunderbolt video ulaz) da biste izabrali da li hoćete da prebacite ili ne. • Yes (Da): Uvek prebacuje na Thunderbolt video ulaz (bez pitanja) kada je Thunderbolt™ 3 aktivni kabl povezan.
Display (Prikaz) Koristite Display (Prikaz) da podesite slike. Aspect Ratio Podešava odnos širina/visina slike na Auto Resize (Odnos širina/ (Automatska promena veličine), 17:9, 16:9 ili Pixelvisina) for-Pixel (Piksel-za-piksel). Digital Cinema Masking (Digitalno maskiranje bioskopskog formata) Podešava Digital Cinema Masking (Digitalno maskiranje bioskopskog formata) na Entire DCI Container (Kompletan DCI kontejner), DCI 1,85:1, DCI 2,39:1 ili DCI 2,35:1.
Set Video Data Podešava stavku Set Video Data Range (Podešavanje opsega video podataka) na Auto Range (Podešavanje (Automatski), Full (Puni) ili Limited (Ograničeni). opsega video podataka) Overscan Frame by 5% (Širenje okvira za 5%) Dozvoljava vam da stavku Overscan Frame by 5% (Širenje okvira za 5%) podesite na Uključeno ili Isključeno. Show Blue Channel only (Prikaži samo plavi kanal) Dozvoljava vam da stavku Show Blue Channel only (Prikaži samo plavi kanal) podesite na Uključeno ili Isključeno.
Uniformity Compensation (Kompenzacija ujednačenosti) Izaberite ekran sa podešavanjima kompenzacije uniformnosti. On (Uključeno) je podrazumevano fabričko podešavanje. Uniformity Compensation (Kompenzacija ujednačenosti) podešava različite oblasti ekrana u odnosu na sredinu da bi postigla ravnomerno osvetljenje i boju preko celog ekrana. NAPOMENA: Korisniku se savetuje da koristi podrazumevano fabričko podešavanje jačine osvetljenja kada se uključi Uniformity Compensation (Kompenzacija ujednačenosti).
PBP Mode (PBP režim) Podešava režim PBP (Slika po slika) na AA, AB ili Off (Isključeno). Pritisnite dugme 50 │ Rukovanje monitorom da biste omogućili PBP režim.
PBP (Sub) Izaberite neki od različitih video signala koji mogu biti povezani na vaš monitor za PBP potprozor. Pritisnite da biste izabrali ulazni signal PBP dugme potprozora. PBP Input Source Toggle (Prebacivanje PBP ulaznog izvora) Izaberite da biste prebacivali između ulaznih izvora u PBP režimu. Pritisnite dugme za prebacivanje između ulaznih izvora u PBP režimu. NAPOMENA: Nije dostupno kada je PBP režim postavljen na AA.
Gamma (Sub) Podešava Gamma (Sub) (Opseg (Sub)) na 1,6, 1,8, (Opseg (Sub)) 2,0, 2,2, 2,4, 2,6, BT.1886, sRGB ili Native (Prirodno). NAPOMENA: Nije dostupno kada je Color Gamut (Sub) (Opseg boja (Sub)) podešen na Native (Prirodno). Sharpness Podesite nivo oštrine slike u PBP režimu. (Sub) (Oštrina Pritisnite dugme da biste povećali oštrinu i pritisnite (Sub)) dugme Audio (Zvuk) da biste smanjili oštrinu. Omogućava vam da podesite audio izvor sa glavnog prozora ili potprozora.
Calibration Target (Cilj kalibracije) Dozvoljava vam da podesite cilj kalibracije na DCI P3 D65 G2.4 L100, BT.709 D65 BT1886 L100, BT.2020 D65 BT1886 L100, sRGB D65 sRGB L250, Adobe RGB D65 G2.2 L250, Adobe RGB D50 G2.2 L250, CAL 1 ili CAL 2. NAPOMENA: Sledeće opcije za Color Space (Prostor boje) nisu dostupne kao ciljevi kalibracije: Native (Prirodno), Custom 1 (Prilagođeno 1), Custom 2 (Prilagođeno 2) i Custom 3 (Prilagođeno 3).
Based Colorimeter Profile (Profil zasnovan na kalorimetru) Dozvoljava vam da podesite Based Colorimeter Profile (Profil zasnovan na kalorimetru) na Built-in (Ugrađeni) ili Ext. Colorimeter (Eksterni kalorimetar) (korelisani eksterni kalorimetar). Prebacivanje profila može da dovede do nekonzistetnih rezultata u odnosu na prethodnu kalibraciju. Preporučuje se da se monitor ponovo kalibriše nakon prebacivanja profila. NAPOMENA: Korisnik može da primeni različite profile kalibracije. Da bi izabrao profil Ext.
Validation (Validacija) Obavite validaciju za kalibraciju boje pomoću ugrađenog kalorimetra. Validate Now Dozvoljava vam da pokrenete validaciju boje. (Validiraj sada) Validation Target (Cilj validacije) Dozvoljava vam da podesite cilj validacije na DCI P3 D65 G2.4 L100, BT.709 D65 BT1886 L100, BT.2020 D65 BT1886 L100, sRGB D65 sRGB L250, Adobe RGB D65 G2.2 L250, Adobe RGB D50 G2.2 L250, CAL 1 ili CAL 2.
Show Last Validation Results (Prikaži rezultate poslednje validacije) Dozvoljava vam da pregledate najnovije rezultate validacije. Scheduler Zakazuje automatsku kalibraciju ili validaciju. Dozvoljava (Zakazivanje) vam da podesite Scheduler (Zakazivanje) na Off (Isključeno), Calibration (Kalibracija), Validation (Validacija) ili Calibration + Validation (Kalibracija + validacija).
Menu (Meni) Izaberite ovu opciju da biste podesili postavke OSD-a, kao što je jezik OSD-a, vremenski period tokom kog meni ostaje na ekranu i tako dalje. Language (Jezik) Opcije za Language (Jezik) podešavaju OSD displej na jedan od osam jezika (engleski, španski, francuski, nemački, brazilski portugalski, ruski, pojednostavljeni kineski ili japanski). Auto Rotation Dozvoljava vam da podesite Auto Rotation (Automatska (Automatska rotacija) na Uključeno ili Isključeno.
Lock Sa zaključanim kontrolnim dugmadima na monitoru, (Zaključavanje) možete sprečiti da neko pristupi kontrolama. Time se takođe sprečava slučajna aktivacija podešavanja sa više uporednih monitora. • Menu Buttons (Dugmad Meni): Sva dugmad menija/funkcijska dugmad (osim dugmeta za uključivanje i isključivanje) su zaključana i korisnik im ne može pristupiti. • Power Button (Dugme za uključivanje i isključivanje): Zaključano je samo dugme za uključivanje i isključivanje i korisnik mu ne može pristupiti.
Alternativna metoda zaključavanja [za dugmad menija/ funkcijsku dugmad]: Takođe možete pritisnuti i zadržati dugme menija/funkcijsko dugme pored dugmeta za uključivanje i isključivanje oko 4 sekunde da biste podesili opcije zaključavanja. NAPOMENA: Da otključate dugme(ad), pritisnite i zadržite dugme menija/funkcijsko dugme pored dugmeta za uključivanje i isključivanje oko 4 sekunde. Reset Menu (Meni Resetovanje) Resetujte sva OSD podešavanja na fabričke unapred podešene vrednosti.
Power Button Omogućava vam da uključite ili isključite LED indikator napajanja da biste uštedeli energiju. LED (LED dugme za uključivanje i isključivanje) USB-A Charging (USB-A punjenje) Daje mogućnost da omogućite ili onemogućite funkciju punjenja USB tipa A (Portovi za preuzimanje) tokom režima pripravnosti monitora. USB-C Charging (USB-C punjenje) Daje mogućnost da omogućite ili onemogućite Always On USB Type-C Charging (Uvek uključen USB tipa C punjenje) funkciju tokom režima isključenog monitora.
Others (Ostalo) Display Info (Prikaz informacija) Prikazuje trenutna podešavanja monitora. Set Date and Podešava datum i vreme za monitor. Time (Podesi NAPOMENA: Sinhronizujte datum i vreme u sledećim datum i vreme) slučajevima: • Prvo podešavanje vašeg monitora. • Monitor je bio isključen sa napajanja više od 10 dana.
DDC/CI DDC/CI (Kanal za prikaz podataka/interfejs za komande) omogućava da se parametri vašeg monitora (svetlina, balans boje itd.) podese preko softvera na vašem računaru. Možete da onemogućite ovu funkciju tako što ćete izabrati Off (Isključeno). Omogućite ovu funkciju za najbolje korisničko iskustvo i optimalne performanse vašeg monitora.
LCD Conditioning (LCD kondicioniranje) Firmware (Firmver) Service Tag (Servisna oznaka) Reset Others (Resetuj ostalo) Pomaže u smanjenju ređih slučajeva zadržavanja slike. U zavisnosti od stepena zadržavanja slike, možda je potrebno neko vreme da se program pokrene. Možete da omogućite ovu funkciju tako što ćete izabrati On (Uključeno). Prikazuje verziju firmvera vašeg monitora. Prikazuje serijski broj servisne oznake vašeg monitora.
OSD poruke upozorenja Kada monitor ne podržava određeni režim rezolucije, videćete sledeću poruku: NAPOMENA: Poruka može biti malo drugačija u odnosu na povezani ulazni signal. To znači da monitor ne može da se sinhronizuje sa signalom koji prima sa računara. Pogledajte Specifikacije monitora za horizontalne i vertikalne frekventne opsege koje adresira ovaj monitor. Preporučeni režim je 3840 x 2160.
NAPOMENA: Ako je izabrano Yes (Da), poruka se neće pojaviti kada sledeći put hoćete da promenite podešavanje Luminance (Jačina osvetljenja).
Kada monitor uđe u režim pripravnosti, pojavljuje se sledeća poruka: Aktivirajte računar i probudite monitor da biste dobili pristup OSD-u. NAPOMENA: Poruka može biti malo drugačija u odnosu na povezani ulazni signal. Ukoliko pritisnete bilo koje dugme koje nije dugme za uključivanje i isključivanje, pojavljuje se sledeća poruka u zavisnosti od izabranog unosa: NAPOMENA: Poruka može biti malo drugačija u odnosu na povezani ulazni signal.
Kada je monitor povezan DP/HDMI konekcijom i kada je Thunderbolt™ 3 aktivan kabl povezan sa notebook računarom koji podržava DP alternativni režim, ako je USB-C Charging (USB-C punjenje) omogućen, pojavljuje se sledeća poruka: Ako se izabere Factory Reset (Fabričko resetovanje), pojavljuje se sledeća poruka: Ako se izabere Yes (Da), pojavljuje se sledeća poruka: Pogledajte Rešavanje problema za više informacija.
Podešavanje maksimalne rezolucije Za podešavanje maksimalne rezolucije monitora: U operativnim sistemima Windows® 7, Windows® 8 i Windows® 8.1: 1. Samo za operativne sisteme Windows® 8 i Windows® 8.1, izaberite pločicu Radna površina da biste prebacili na klasičnu radnu površinu. 2. Kliknite desnim klikom na radnu površinu i kliknite na Rezolucija ekrana. 3. Kliknite na padajuću Rezoluciju ekrana i izaberite 3840 x 2160. 4. Kliknite na U redu. U operativnom sistemu Windows® 10: 1.
Kalibracija boje Izvršite Calibration (Kalibracija) sa ugrađenim kalorimetrom da biste kalibrisali boju monitora. Korišćenje OSD menija 1. Korišćenjem OSD menija podesite kriterijume kalibracije kako želite. Zatim izaberite Calibrate Now (Kalibriši sada). 2. Pojavljuje se sledeća poruka, izaberite Yes (Da) da biste nastavili proces.
3. Kalibracija će započeti automatski. Korišćenje tastera prečice sa video signalom 1. Pritisnite bilo koje funkcijsko dugme da prikažete tastere prečica. 2. Pritisnite dugme . 3. Pojavljuje se sledeća poruka, izaberite Yes (Da) da biste nastavili proces.
4. Kalibracija će započeti automatski. Korišćenje tastera prečice bez video signala Možete da izvršite kalibraciju za monitor bez dovođenja ulaznog signala sa računara. 1. Pritisnite bilo koje funkcijsko dugme da prikažete tastere prečica. 2. Pritisnite dugme .
3. Kalibracija će započeti automatski. NAPOMENA: Calibration (Kalibracija) u Režim portreta se ne preporučuje. NAPOMENA: Za detaljne funkcije, pogledajte Calibration (Kalibracija). Zaustavljanje procesa kalibracije Proces kalibracije možete da zaustavite u bilo kom trenutku. 1. Tokom procesa kalibracije pritisnite bilo koje funkcijsko dugme i pojaviće se sledeća poruka. 2. Izaberite Yes (Da) da zaustavite proces.
Validacija boje Obavite Validation (Validacija) za kalibraciju boje pomoću ugrađenog kalorimetra. Korišćenje OSD menija 1. Korišćenjem OSD menija podesite kriterijume validacije kako želite. Zatim izaberite Validate Now (Validiraj sada) da biste pokrenuli proces validacije. 2. Pojavljuje se sledeća poruka, izaberite Yes (Da) da biste nastavili proces.
3. Validacija će započeti automatski. Korišćenje tastera prečice bez video signala Možete da izvršite validaciju za monitor bez dovođenja ulaznog signala sa računara. 1. Pritisnite bilo koje funkcijsko dugme da prikažete tastere prečica. 2. Pritisnite dugme .
3. Pojavljuje se sledeća poruka, izaberite Yes (Da) da biste nastavili proces. NAPOMENA: Validation (Validacija) u Režim portreta se ne preporučuje. NAPOMENA: Za detaljne funkcije, pogledajte Validation (Validacija). Zaustavljanje procesa validacije Proces validacije možete da zaustavite u bilo kom trenutku. 1. Tokom procesa validacije pritisnite bilo koje funkcijsko dugme i pojaviće se sledeća poruka. 2. Izaberite Yes (Da) da zaustavite proces.
Korišćenje naginjanja, okretanja i vertikalnog proširenja NAPOMENA: Ovo je primenljivo za monitor sa stalkom. Kada se kupi bilo koji drugi stalak, potražite uputstva za podešavanje u odgovarajućem uputstvu za podešavanje stalka. Naginjanje i okretanje Kada se stalak pričvrsti na monitor, možete da nagnete ili okrenete monitor za najugodniji ugao gledanja. NAPOMENA: Stalak je odvojen kada se monitor isporuči iz fabrike.
Vertikalno proširenje NAPOMENA: Stalak se vertikalno proširuje do 130 mm. Slika u nastavku ilustruje kako se stalak proširuje vertikalno. Rotiranje monitora Pre nego što zarotirate monitor, vaš monitor treba da bude u potpunosti vertikalno proširen (Vertikalno proširenje) i potpuno podignut nagore da bi se izbeglo udaranje u donju ivicu monitora.
Zarotirajte u smeru kretanja kazaljki na satu Zarotirajte u smeru suprotnom smeru kretanja kazaljki na satu 78 │ Rukovanje monitorom
Rešavanje problema UPOZORENJE: Pre nego što započnete procedure u ovom odeljku, pratite Bezbednosna uputstva. Samotestiranje Vaš monitor obezbeđuje samotestiranje koje vam omogućava da proverite da li vaš monitor pravilno funkcioniše. Ukoliko su vaš monitor i računar pravilno povezani ali je ekran monitora i dalje taman, pokrenite samotestirnaje tako što ćete obaviti sledeće korake: 1. Isključite i računar i monitor. 2. Isključite video kabl sa poleđine računara. 3. Uključite monitor.
Ugrađena dijagnostika Vaš monitor ima ugrađenu dijagnostičku alatku koja vam pomaže da odredite da li je nepravilnost ekrana do koje dolazi inherentan problem sa vašim monitorom ili sa vašim računarom i video karticom. NAPOMENA: Možete pokrenuti ugrađenu dijagnostiku samo kada je video kabl isključen i monitor je u režimu samotestiranja. Za pokretanje ugrađene dijagnostike: 1. Pobrinite se da ekran bude čist (nema čestica prašine na površini ekrana). 2. Isključite video kabl(ove) sa poleđine računara.
4. Pritisnite dugme pritisnite dugme da označite ikonu Diagnostics (Dijagnostika), a zatim i pojavljuje se sivi ekran. 5. Pažljivo pregledajte da li na ekranu ima nepravilnosti. 6. Ponovo pritisnite Dugme 1 na prednjoj ploči. Boja ekrana se menja u crvenu. 7. Pregledajte da li na displeju ima nepravilnosti. 8. Ponovite korake 6 i 7 da biste pregledali prikaz na zelenom, plavom, crnom, belom i ekranu sa tekstom. Test je završen kada se pojavi ekran sa tekstom. Da biste izašli, ponovo pritisnite Dugme 1.
Uobičajeni problemi Sledeća tabela sadrži opšte informacije o uobičajenim problemima sa monitorom do kojih može doći i moguća rešenja: Uobičajeni simptomi Šta se dešava Nema videa/ LED lampica napajanja je isključena Nema slike Moguća rešenja • Proverite da li je video kabl koji povezuje monitor i računar pravilno povezan i pričvršćen. • Potvrdite da utičnica pravilno funkcioniše koristeći bilo koju drugu električnu opremu. • Proverite da li je dugme za uključivanje/ isključivanje pritisnuto do kraja.
Nestabilan/ podrhtavajući video Talasasta slika ili blago pomeranje • Resetujte monitor na fabrička podešavanja. • Proverite faktore okruženja. • Premestite monitor i testirajte ga u drugoj prostoriji. • Dell monitori su dizajnirani za optimalan rad sa inoks kablovima koje isporučuje kompanija Dell. Dell ne garantuje video kvalitet i performanse kada se koriste kablovi koje nije isporučila kompanija Dell. Nedostajući pikseli LCD ekran ima mrlje • Uključite i isključite nekoliko puta.
Horizontalne/ vertikalne linije Ekran ima jednu ili više linija • Resetujte monitor na fabrička podešavanja. • Obavite proveru funkcije samotestiranja monitora ukoliko se ove linije pojavljuju i u režimu samotestiranja. • Proverite da li postoje savijeni ili polomljeni pinovi u konektoru video kabla. • Pokrenite ugrađenu dijagnostiku. Problemi sa sinhronizacijom Ekran je ispreturan ili izgleda pocepan • Resetujte monitor na fabrička podešavanja.
Pogrešna boja Boja slike nije ispravna • Promenite podešavanja Preset Modes (Unapred određenih režimi) u OSD meniju Color (Boja) u zavisnosti od aplikacije. • Podesite vrednost C/Z/P pod stavkom Custom Color (Prilagođena boja) u OSD meniju Color (Boja). • Promenite Input Color Format (Unos formata boje) u PC RGB ili YPbPr u OSD meniju Color (Boja). • Pokrenite ugrađenu dijagnostiku.
Podešavanje monitora pomoću dugmadi na prednjoj ploči nije moguće OSD se ne pojavljuje na ekranu Nema ulaznog signala kada se pritisnu korisničke kontrole Nema slike LED svetlo je belo • Isključite monitor, isključite kabl za napajanje, ponovo ga uključite, a zatim uključite monitor. • Proverite da li je OSD meni zaključan. Ukoliko jeste, pritisnite i zadržite Meni/ funkcijsko dugme pored dugmeta za uključivanje i isključivanje na 4 sekunde da biste otključali (za više informacija Lock (Zaključavanje)).
Nema video signala na HDMI portu Kada je povezan • Izvucite HDMI kabl iz bazne stanice, zatim priključite Thunderbolt™ kabl na na neku baznu Notebook uređaj. Priključite HDMI kabl 7 stanicu, na HDMI sekundi kasnije. portu nema video signala nakon što se Thunderbolt™ kabl izvuče, a zatim ponovo priključi na Notebook uređaj.
Ne prikazuje se Nema video signala kada se slika koristi Thunderbolt™ 3 veza posle uključivanja/ isključivanja jednosmernog napajanja, buđenja iz režima pripravnosti Nema video signala kada se koristi veza USB-C DP alternativnog režima posle uključivanja/ isključivanja jednosmernog napajanja, buđenja iz režima pripravnosti Ne prikazuje se slika 88 │ Rešavanje problema • Izvucite/priključite Thunderbolt™ 3 aktivan kabl. • Proverite da li je povezani uređaj u skladu sa Thunderbolt™ 3 specifikacijom.
USB 3.2 interfejs velike brzine je spor USB 3.2 periferijski uređaji velike brzine rade sporo ili uopšte ne rade • Proverite da li je vaš računar kompatibilan sa USB 3.2. • Neki računari imaju USB 3.1 , USB 3.0, USB 2.0 i USB 1.1 portove. Proverite da li se koristi odgovarajući USB port. • Ponovo povežite kabl za otpremanje na vaš računar. • Ponovo povežite USB periferijske uređaje (konektor za preuzimanje). • Ponovo pokrenite računar.
Dodatak UPOZORENJE: Bezbednosna uputstva UPOZORENJE: Korišćenje komandi, podešavanja ili procedura koje nisu navedene u dokumentaciji može dovesti do izloženosti strujnom udaru, električnim opasnostima i/ili mehaničkim opasnostima. Za informacije o bezbednosnim uputstvima, pogledajte Bezbednosne, regulativne i informacije o zaštiti životine sredine (SERI).
Podrška video signala i USB-a preko USB-C porta Podrška za video rezoluciju i USB pri povezivanju sa monitorom preko USB-C porta. Video USB Povezivanje na host računar Korišćeni kabl za otpremanje (host računar na port 6-1 monitora) 4K (Direktna veza) 4K (Lančana veza) TBT3 uređaj je povezan na TBT3 preuzimanje (port 6-2 monitora) USB-A USB A-na-C* Ne Ne Ne USB2.0 USB2.0/ 3.2 USB-C MFDP Ne Ne Ne USB2.0 USB2.0/ 3.2 TBT3 pasivan Ne Ne Ne USB2.0 USB2.0/ 3.
Kupovina Thunderbolt™ 3 pasivnog kabla Regija Link https://www.dell.com/en-us/shop/accessories/apd/a9905599 Dell vebsajt https://www.dell.com/en-us/shop/accessories/apd/a9905597 https://www.dell.com/en-us/shop/accessories/apd/a9269731 SAD https://www.belkin.com/us/p/P-F2CD081/ https://www.delock.com/produkte/G_84846/merkmale.html/ EMEA https://www.hama.cz/hama-kabel-thunderbolt-3-usb-c-typ-cvidlice--vidlice-20-gb-s-100-w-1-m/ https://www.lindy-international.com/Thunderbolt-3-Cable2m.