Dell UltraSharp UP3017A 使用指南 型號: UP3017A 安規型號:UP3017t
註:「註」指出可協助您善用電腦的重要資訊。 注意:「注意」代表若未遵守指示,可能會導致硬體毀損或資料遺失。 警告:「警告」代表財物損失及人員傷亡的可能性。 版權所有 © 2020 Dell Inc. 保留所有權利。 本產品受到美國及國際版權和智慧財產法律保護。 Dell™ 和 Dell 標誌為 Dell Inc.
目錄 關於顯示器 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 包裝內容物 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 產品特色 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 零件與控制鈕 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 顯示器規格 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 隨插即用功能 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
內建診斷 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 一般問題 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 產品特定問題 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 通用串列匯排流(USB)特定問題 . . . . . . . . . . . . . . . . . . . . . . 53 附錄 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 安全指示 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
關於顯示器 包裝內容物 顯示器隨附下列元件。請檢查是否已收到所有元件,如有缺少,請聯絡 Dell。 註:部分品項屬於選購品,因此並未隨附於顯示器。部分功能或媒體不適用於特定國 家。 顯示器 立架 底座 電源線(因國家而異) USB 3.
DP 連接線(DP 到 mDP) PremierColor UP3017 Color Calibration Factory Report Every Dell UP3017 is shipped incorporating pre-tuned sRGB and AdobeRGB with average DeltaE<2. Color and Luminance Uniformity is adjusted across the screen to meet DeltaE<2 and 97-102% respectively. This helps prevent significant color inconsistency or inaccuracy. In addition, a tighter grey-scale tracking helps enable ultrasmooth color gradation.
零件與控制鈕 正面視圖 1 標號 1 2 2 說明 功能按鈕(如需更多資訊,請參閱顯示器操作) 電源開啟 關閉按鈕(附LED指示燈) 恆亮白燈表示顯示器開啟並正常運作。閃爍白燈表示顯示器處於待機模式。 關於顯示器 | 7
背面視圖 1 2 3 4 5 ஂ ถ ཱྀ ᑺ ᒦ ਪ ca t io n y Energ nse rt i fi Co r va t i o n C e 7 6 標號 1 2 3 4 5 6 說明 100 mm x 100 mm VESA 載掛 孔(VESA 護蓋底下) 安規貼紙 立座釋放按鈕 安全鎖槽 條碼、序號及服務標籤 Dell 喇叭組安裝槽 7 連接線整理槽 用途 使用 VESA 相容壁掛套件 (100 mm x 100 mm) 的 壁掛式顯示器。 列出本產品所獲的安規認證。 使用安全鎖固定螢幕。 使用安全纜鎖固定顯示器(另售)。 若需聯絡 Dell 取得技術支援,則請參閱此貼紙。 安裝選購的 Dell 喇叭組。 註:固定 Dell 音箱棒之前請先撕下覆蓋安裝插槽 的塑膠條。 Dell 喇叭組另售。 可將連接線穿過插槽,方便加以整理。 側面視圖 USB 下游連接埠 含 電池圖示的連接埠支援 BC 1.
底部視圖 10 1 2 3 4 5 67 8 9 標號 1 2 說明 AC 電源插孔 HDMI1 連接埠 用途 連接顯示器的電源線 3 HDMI2 連接埠 4 DP 連接器(輸入) 連接電腦的 DP 電纜 5 6 mDP 接頭(輸入) DP 連接器(輸出) 7 音訊線路輸出連接埠 8 USB 上游連接埠 9 USB 下游連接埠 以 mDP 轉 DP 纜線連接您的電腦 供 MST(多串流傳輸)相容螢幕所用的 DP 輸出。DP 1.
顯示器規格 螢幕類型 面板類型 寬高比 主動式矩陣 - TFT LCD 橫向電場效應技術 16:10 可視影像尺寸 對角線 有效區域 水平 垂直 面積 像素點距 每英吋像素 (PPI) 觀賞角度 垂直 水平 亮度輸出 對比度 顯示畫面塗層 背光 反應時間 (灰階到灰階) 色深 色階* 75.62 公分(30 英吋) 641.3 公釐(25.2 英吋) 400.8 公釐(15.8 英吋) 257025.0 平方公釐(398.2 平方英吋) 0.251 公釐 x 0.251 公釐 101 178 度(標準值) 178 度(標準值) 350 cd/m²(標準值) 1000 比 1(標準值) 前端偏光片 (3H) 採抗眩光處理及表面硬化鍍膜 白色 LED、EDGELIGHT 系統 6 ms (快速模式) 8 ms (正常模式) 10.7億種顏色 99% Adobe RGB 99% sRGB 99% REC709 99% DCI-P3 校正精準度 連接性 Delta E < 2 (平均值) • 1 x DP 1.2 (HDCP 1.4) • 1 x mDP 1.2 (HDCP 1.4) • 1 x DP 1.
可調整性 支架可調整高度 150 mm 傾斜 旋轉 轉軸 線纜管理 Dell Display Manager (DDM) 相容性 -5° 至 21° -30° 至 30° -90° 至 90° 有 方便排列及其他重要功能 安全性 安全鎖孔 (纜線鎖另售) 防竊底座及鎖孔 (至面板) 註 *:在自訂模式預設下僅限原始面板。 解析度規格 水平掃瞄範圍 垂直掃描範圍 30 kHz to 113 kHz (DP/HDMI) 50Hz - 86 Hz (DP/HDMI) 最高預設解析度 2560 x 1600 at 60 Hz 視訊顯示功能(DP及HDMI播放) 480i, 480p, 576i, 576p, 720p, 1080i, 1080p, QHD 關於顯示器 | 11
預設顯示模式 顯示模式 水平頻率 (kHz) 垂直頻率 (Hz) 像素時脈 (MHz) 同步極性 (水平 垂直) 720 x 400 31.5 70.0 28.3 -/+ VESA, 640 x 480 31.5 60.0 25.2 -/- VESA, 640 x 480 37.5 75.0 31.5 -/- VESA, 800 x 600 37.9 60.0 40.0 +/+ VESA, 800 x 600 46.9 75.0 49.5 +/+ VESA, 1024 x 768 48.4 60.0 65.0 -/- VESA, 1024 x 768 60.0 75.0 78.8 +/+ VESA, 1152 x 864 67.5 75.0 108.0 +/+ VESA, 1280 x 1024 64.0 60.0 108.0 +/+ VESA, 1280 x 1024 80.0 75.0 135.0 +/+ VESA, 1600 x 1200 75.0 60.0 162.
MST Multi-Stream Transport (MST)模式 MST源顯示器 2560 x 1600/60 Hz 可支持外部顯示器最大數量 2560 x 1600/60 Hz 1 1920 x 1200/60 Hz 2 註: 支援的最大外部螢幕解析度僅 2560x1600 60Hz。 電氣規格 影像輸入訊號 輸入電壓 湧浪電流 耗電量 頻率 電流 • 每條差動線路各有數位視訊訊號 每條差動線路具有 100 ohm 阻抗 • DP/HDMI 訊號輸入支援 100–240 VAC / 50 或 60 Hz ± 3 Hz / 1.6 A(最大) 120 V: 30 A (最大) 240 V: 60 A (最大) 0.2 W (關閉模式)1 0.3 W (待機模式)1 35.8 W (開啟模式)1 108 W (最大)2 38.4 W (Pon)3 120.
物理特性 接頭類型 訊號連接線類型 (隨附) 尺寸(含立座) 高度(展開時) 高度(壓縮時) 寬度 深度 尺寸(不含立座) 高度 寬度 深度 立座尺寸 高度(展開時) 高度(壓縮時) 寬度 深度 重量 • DP (HDCP 1.4) 連接器 (包含 DP 輸入和 DP 輸出) • mDP (HDCP 1.4) 連接器 • HDMI (HDCP 1.4) 連接器 • 音訊線路輸出 • USB 3.0 接頭 (含 電池圖示的連接埠支援 BC 1.2。) DP 轉 mDP, 1.8 M 纜線 USB 3.0, 1.8 M 纜線 632.3 公釐(24.89 英吋) 482.3 公釐(18.99 英吋) 686.9 公釐(27.04 英吋) 217.0 公釐(8.54 英吋) 447.1 公釐(17.60 英吋) 686.9 公釐(27.04 英吋) 58.0 公釐(2.28 英吋) 478.2 公釐(18.83 英吋) 430.5 公釐(16.95 英吋) 343.5 公釐(13.52 英吋) 217.0 公釐(8.54 英吋) 含包裝箱 13.10 公斤(28.88 磅) 含立座組與線材 9.
環境特性 遵循標準 TCO 認證顯示器。 有 符合 RoHS 規範。 有 無 BFR/PVC 顯示器 (不包 有 括外部纜線)。 溫度 運作 0℃ 至 35℃(32 °F 至 95 °F) 未運作 -20℃ 至 60℃(-4 °F 至 140 °F) 濕度 運作 未運作 高度 運作 未運作 散熱 10% 至 80%(非冷凝) 5% 至 90%(非冷凝) 最高 5,000 公尺(16,404 英尺) 最高 12,192 公尺(40,000 英尺) 368.51 BTU/時(最大) 122.
針腳配置 DP 連接器(輸入) 針腳編號 20 pin 端,已連接訊號連接線 1 ML3(n) 2 GND 3 ML3(p) 4 ML2(n) 5 GND 6 ML2p) 7 ML1(u) 8 GND 9 ML1(p) 10 ML0(n) 11 GND 12 ML0(p) 13 CONFIG1 14 CONFIG2 15 AUX CH (p) 16 DP_Cable Detect 17 AUX CH (n) 18 熱插拔偵測 19 GND 20 +3.
DP 連接器(輸出) 針腳編號 20 pin 端,已連接訊號連接線 1 ML0(p) 2 GND 3 ML0(n) 4 ML1(p) 5 GND 6 ML1(n) 7 ML2(p) 8 GND 9 ML2(n) 10 ML3(p) 11 GND 12 ML3(n) 13 CONFIG1 14 CONFIG2 15 AUX CH(p) 16 GND 17 AUX CH(n) 18 熱插拔偵測 19 GND 20 DP_PWR 關於顯示器 | 17
mDP 接頭 針腳編號 20 pin 端,已連接訊號連接線 1 GND 2 熱插拔偵測 3 ML3(n) 4 CONFIG1 5 ML3(p) 6 CONFIG2 7 GND 8 GND 9 ML2 (n) 10 ML0 (p) 11 ML2 (p) 12 ML0 (p) 13 GND 14 DP_Cable Detect 15 ML1 (n) 16 AUX (p) 17 ML1 (p) 18 AUX (n) 19 GND 20 +3.
HDMI 連接器 針腳編號 19 pin 端,已連接訊號連接線 1 TMDS DATA 2+ 2 TMDS DATA 2 SHIELD 3 TMDS DATA 2- 4 TMDS DATA 1+ 5 TMDS DATA 1 SHIELD 6 TMDS DATA 1- 7 TMDS DATA 0+ 8 TMDS DATA 0 SHIELD 9 TMDS DATA 0- 10 TMDS CLOCK+ 11 TMDS CLOCK SHIELD 12 TMDS CLOCK- 13 CEC 14 Reserved (N.C.
通用串列匯排流(USB)介面 本節提供顯示器可用的 USB 連接埠之相關資訊。 註:在 USB 下游連接埠(帶有 電池圖示的連接埠)及 BC 1.2 相容裝置上最高 2A;在其他 2個 USB 下游連接埠上最高 0.9 A。 電腦具有下列 USB 連接埠: • 2 個上游 - 底部 • 4 個下游 - 2 個位於左側,2 個位於底部 充電埠 - 若裝置相容 BC 1.2,則含有 電池圖示的連接埠支援快速充電功能。 註:顯示器的 USB 連接埠只有在顯示器電源開啟或處於省電模式時才可運作。若關閉顯 示器電源再加以開啟,則相連的周邊設備可能需經過幾秒鐘才能恢復正常功能。 傳輸速度 資料速率 耗電量 超高速(SuperSpeed) 5 Gbps 4.5 W(各連接埠最大值) 高速(Hi-Speed) 480 Mbps 2.5 W(各連接埠最大值) 全速(Full speed) 12 Mbps 2.
隨插即用功能 您可將顯示器安裝在任何支援隨插即用功能的電腦。顯示器會自動採用顯示資料頻道 (DDC)通訊協定為電腦提供延伸顯示識別資料(EDID),使電腦可自行配置並將顯示器 設定最佳化。大多數的顯示器安裝步驟皆會自動進行;若有需要,則可自行選擇其他設定。 如需有關變更顯示器設定的詳細資訊,請參閱顯示器操作。 LCD 顯示器品質與像素原則 在 LCD 顯示器的製造過程中,有一或多個像素保持不變狀態並非異常情況。這些像素難以 用肉眼察覺,但其並不會影響顯示器的品質或可用性。如需 Dell 顯示器品質與像素原則的 詳細資訊,請造訪 http://www.dell.
架設顯示器 安裝立座 註:顯示器從工廠出貨時,已將立架和立座拆下。 註:下列流程適用於預設立座。 若是您購買任何其他立座,請參閱立座隨附的說明文件 以進行設定。 注意:將顯示器放置在平坦、清潔及柔軟的表面上,以避免刮傷顯示器面板。 2 3 安裝顯示器底座: 1 取下螢幕保護蓋,並將螢幕正面朝下擺放。 2 將底座上方部位的兩個凸緣插入螢幕背面的溝槽。 3 按下立座,直至立座扣入定位。 22 | 架設顯示器
• 固定底座基部,且三角形記號 朝上。 • 將底座基部凸出的區塊對準底座上的配對插槽。 • 將底座基部區塊完全插入底座插槽中。 架設顯示器 | 23
• 提起螺絲柄並順時針轉動。 • 完全鎖緊螺絲後,將螺絲柄平面摺入凹槽內。 24 | 架設顯示器
使用傾斜、旋轉和垂直展開功能 註:此步驟適用於含立座的顯示器。 購買任何其他立座時,請參閱立座各自的架設指 南, 取得架設說明。 「傾斜(Tilt)」、「旋轉(Swivel)」及「垂直延伸(Vertical Extension)」 透過連接顯示器的立架,您可將顯示器傾斜至最舒適的觀賞角度。 5° 30° 150 mm 30° 21° 註:立座於顯示器原廠出貨時已經拆下。 旋轉顯示器 在您旋轉顯示器之前,您的顯示器應完全垂直伸展並完全傾斜以避免撞擊顯示器的底邊。 1 90° 90° 2 註:欲在您的 Dell 電腦上使用顯示旋轉功能(風景與肖像檢視),您需要 更新顯卡驅動 程式(顯示器未隨附)。 欲下載顯卡驅動程式, 請至 www.dell.
調整您系統的旋轉顯示設定 在旋轉您的顯示器之後,您必須完成下方程序以調整您系統的旋轉顯示設定。 註: 若您 使用非 Dell 電腦,您必須至顯卡驅動程式網站或您電腦製造商網站取得有關 旋轉作業系統的資訊。 欲調整旋轉顯示設定: 1 2 3 4 請在桌面上按一下右鍵,然後按一下內容。 在 設定 分頁上,按一下 進階。 若您使用 ATI 圖形卡,請選擇旋轉選項並設定偏好的旋轉。 若您使用 nVidia 圖形卡,請選擇 nVidia 選項,在左手列選擇 NVRotate ,接著選擇偏 好的旋轉。 5 若您使用 Intel® 圖形卡,請選擇 Intel 圖形選項,請點選圖形屬性,選擇旋轉選項,接 著設定偏好的旋轉。 註:若您未見旋轉選項或旋轉不正確,請至 www.dell.
單一顯示器連接 連接 DP (或 mDP) 纜線 mDP DP 註:預設為 DP 連接埠。請選擇螢幕的輸入來源以切換為 mDP。 連接 HDMI 纜線(另售) HDMI HDMI 連接 USB 纜線 完成連接 DP 轉 mDP 連接線後,請參閱以下程序將 USB 3.0 連接線連接至電腦,即可完成 顯示器設定: 1 a.連接一部電腦 將上游 USB 3.0 連接埠(隨附連接線)接至電腦上合適的 USB 3.0 連接埠。 b.連接兩部電腦 連接上游 USB 3.0 連接埠至兩部電腦上的 USB 3.0 連接埠。接著使用 OSD 功能表選 擇兩個 USB 上游來源和輸入來源。請參閱 USB 選擇開關。 註:連接兩部電腦至螢幕時,可從 OSD 功能表變更 USB 選項設定,將螢幕的鍵盤與 滑鼠 USB 下游連接埠指定為兩部電腦的不同輸入訊號。(請參閱 USB 選項了解詳細資 訊) 2 將 USB 3.0 周邊裝置接至顯示器上的下游USB 3.
USB USB a. 連接一部電腦 USB USB 4 b. 連接兩部電腦 打開顯示器與電腦。 若顯示器出現影像,就代表安裝已經完成。若未顯示影像,請參閱疑難排解。 多部顯示器連接 連接顯示器應用 DP(MST)功能 DP out mDP mDP DP 註:支援 DP MST 功能。要使用此功能,您的 PC 圖形卡必須保證 DP 1.
整理連接線 再將所有必要的接線接到電腦和顯示器之後(連接方法請閱連接顯示器)如上所示將所有 接線整妥當。 拆除顯示器立座 注意:為避免移除底座時刮傷 LCD 螢幕,請確定顯示器放置於乾淨柔軟的表面上。 註:下列流程適用於預設立座。 若是您購買任何其他立座,請參閱立座隨附的說明文件以 進行設定。 拆下立座: 1 請將顯示器放置在軟布或軟墊上。 2 按住底座卸除按鈕。 3 將底座提起,自顯示器移除。 3 2 架設顯示器 | 29
壁掛安裝(選擇性) ஂ ถ ཱྀ ᑺ ᒦ ਪ ca t io n y Energ ti fi Co n s e r va ti o n C er 註:使用 M4 x 10 mm 螺絲,將顯示器與牆壁裝設套件連接。 請參考 VESA 相容牆壁裝設套件隨附的指示說明。 1 將顯示器放在平穩的桌面,並加墊軟布或墊子。 2 拆下立座。 3 使用十字螺絲起子拆除固定塑膠蓋的四顆螺絲。 4 將壁掛套件-的壁掛架安裝至顯示器。 5 遵照壁掛套件隨附的說明書將顯示器安裝至牆壁。 註:僅限搭配名列 UL 或 CSA 或 GS 標準的壁掛式托架使用,且最小重量/承載重量為 6.49 kg (14.
顯示器操作 開啟顯示器電源 按下 按鈕以開啟顯示器。 使用前面板控制項目 使用顯示器前方的控制按鈕,調整顯示之影像的特性。在您使用這些按鈕調整控制項目 時,OSD 會在特性變更時顯示特性的數值。 1 2 3 4 5 6 顯示器操作 | 31
下表為前面板按鈕的說明: 前-面板按鈕 說明 1 使用此按鈕可從預設色彩模式清單中進行選擇。 捷徑鍵: 預設模式 2 使用此按鈕可直接進入Brightness/Contrast (「亮度 對比度」)功能表。 Shortcut key (捷徑鍵)/Brightness(亮度)/ Contrast(對比度) 3 使用本按鈕從輸入來源清單中選擇。 捷徑鍵: 輸入來源 4 使用此按鈕可啟動螢幕顯示(OSD)並選取 OSD 中的 選項。 請參閱進入功能表系統。 功能表 5 使用此按鈕可返回主功能表或退出 OSD 主功能表。 離開 6 開啟或關閉顯示器。 恆亮白燈表示顯示器開啟並正常運作。閃爍白燈表示 顯示器處於待機模式。 Power Button(電源按鈕) (含電源狀態指示燈) 32 | 顯示器操作
前-面板按鈕 使用顯示器前方的按鈕可調整影像設定。 1 2 3 前-面板按鈕 說明 1 使用向上(升高)和向下(降低)按鍵可調整 OSD 功能表中 的項目。 向上 向下 2 使用確定按鍵可確認所選項目。 確定 3 使用返回按鍵可回到上一層功能表。 返回 顯示器操作 | 33
使用螢幕顯示(OSD)功能表 進入功能表系統 註:若移至另一層 OSD 功能表、退出 OSD 功能表或等候 OSD 功能表消失,則顯示器 將自動儲存您使用 OSD 功能表所作的任何變更。 1 按下 按鈕可啟動 OSD 功能表並顯示主功能表。 Dell UltraSharp UP3017A Energy Use Brightness/Contrast Input Source Color Display PIP/PBP 75% USB Selection 75% Audio Energy Menu Personalize Others Resolution : 2560x1600, 60Hz 2 按下 3 按一下 和 按鈕可在選項之間移動。在不同圖示之間移動時,選項名稱會反白。 或 或 按鈕可啟動反白的選項。 4 按下 和 5 按下 按鈕進入滑桿,然後使用 6 按 34 按鈕可選取所需參數。 鍵,返回前一選單,按 | 顯示器操作 或 按鈕即可變更功能表上的指標。 接受並返回前一選單。
圖示 功能表與子功 能表 說明 亮度 使用此功能表可啟動亮度 對比度 對比度調整功能。 Dell UltraSharp UP3017A Energy Use Brightness/Contrast Input Source Color Display PIP/PBP 75% USB Selection 75% Audio Energy Menu Personalize Others Resolution : 2560x1600, 60Hz 亮度 可調整背光的明亮度(最低為 0;最高為 100)。 按下 按鈕可調高亮度。 按下 按鈕可調低亮度。 註:開啟動態對比,即會停用亮度手動調整功能。 對比度 請先調整亮度,並只在需要進一步調整時再調整對比度。 按下 按鈕可增加對比度,按下 按鈕則降低對比度(0 到 100)。 利用對比度可調整顯示器影像的明暗差異。 輸入來源 使用 Input Source(輸入來源)功能表可選擇連接至顯示器的 各種影像輸入。 Dell UltraSharp UP3017A Energy Use Brightness/Contrast DP In
功能表與子功 能表 圖示 DP mDP HDMI1 HDMI2 說明 若使用 DP 連接線連接電腦與顯示器。 按下 選擇 DP 輸入來源。 若使用 mDP 連接線連接電腦與顯示器。 按下 選擇 mDP 輸入來源。 若使用 HDMI1 連接線連接電腦與顯示器。 按下 選擇 HDMI1 輸入來源。 若使用 HDMI2 連接線連接電腦與顯示器。 按下 選擇 HDMI2 輸入來源。 自動選擇 使用 重設輸入來源 將顯示器的輸入來源重設為原廠預設值。 色彩 使用色彩功能表調整色彩設定模式。 選擇自動選擇,螢幕會掃描可用的輸入來源。 Dell UltraSharp UP3017A Energy Use Brightness/Contrast Preset Modes Standard Input Source Input Color Format RGB Color Gamma 2.
圖示 功能表與子功 能表 說明 • • • 標準:預設色彩設定。此為預設模式。 ComfortView: 降低畫面散發藍光亮度,讓眼睛觀看更舒 適。 多媒體:適用於多媒體應用。 電影:適用於電影。 遊戲:適用於多數遊戲應用。 • Color Temp.
功能表與子功 能表 圖示 說明 • Custom Color(自訂色彩):可手動調整色彩設定。按下 和 按鈕可調整紅色、綠色及藍色數值,建立自訂的 預設色彩模式。 使用 與 按鈕選擇增益、位移、色調、飽合度。 Custom Color Gain Offset Hue Saturation 輸入色彩格式 – Gain(增益):選擇此選項可調整輸入 RGB 訊號增益等級(預 設值為 100)。 – Offset(位移):選擇此選項可調整 RGB 黑階位移值(預設值 為 50),控制顯示器的基準色彩。 – Hue(色調):選擇此選項可個別調整RGBCMY色調值(預設 值為 50)。 – Saturation(飽和度):選擇此選項可個別調整RGBCMY飽和 度值(預設值為 50)。 可設定為下列影像輸入模式: RGB:如果您的顯示器使用 HDMI、DP-mDP連接線連接電腦 或 DVD 播放器,請選擇此選項。 YPbPr:若您的 DVD 播放器僅支援 YPbPr 輸出,則選擇此選 項。 Dell UltraSharp UP3017A Energy Use Brightness/Contrast
圖示 功能表與子功 能表 說明 色度 使用 或 調整色度,調整範圍介於「0」至「100」。 註:色度調整功能只有在影片與遊戲模式中才能使用。 飽和度 使用 或 調整飽和度,調整範圍介於「0」至「100」。 註:飽和度調整功能只有在影片與遊戲模式中才能使用。 重設色彩 將顯示器的色彩重設為原廠預設值。 顯示 使用顯示設定調整影像。 Dell UltraSharp UP3017A Energy Use Brightness/Contrast Aspect Ratio Wide 16:10 Input Source Monitor Sleep Sleep After Timeout Color Sharpness 50 Display Dynamic Contrast PIP/PBP Response Time Normal USB Selection MST Off Audio Uniformity Compensation Off Energy Display Info Menu Reset Display Personalize Others
功能表與子功 能表 圖示 PIP/PBP 說明 此功能會用一個視窗顯示另一個輸入來源的影像。 因此可同時 觀賞不同來源的兩個影像。 Dell UltraSharp UP3017A Energy Use Brightness/Contrast PIP/PBP Mode Off Input Source PIP/PBP (Sub) mDP Color PIP Location Top-Right Display USB Select Switch PIP/PBP Video Swap USB Selection Contrast (Sub) Audio Energy Menu Personalize Others Resolution : 2560x1600, 60Hz 主視窗 PIP/PBP 模式 | mDP 子 - 視窗 HDMI1 HDMI2 DP X √ √ √ mDP √ X √ √ HDMI1 √ √ X √ HDMI2 √ √ √ X 註:使用 PIP/PBP 功能時,將停用 DP MST (Daisy Ch
圖示 功能表與子功 能表 USB 選項 說明 從清單中選擇 USB 上游訊號:DP、mDP或HDMI,因此螢幕的 USB 下游連接埠 (如鍵盤與滑鼠) 皆可在連接電腦至其中一個上 游連接埠時由目前的輸入訊號使用。 顯示器和 USB 上游連接埠連線皆可透過選擇輸入來源功能變 更。 當您只使用一個上游連接埠時,將啟用連接的上游連接埠。 Energy Use Dell UltraSharp UP3017A Brightness/Contrast USB 1 DP Input Source USB 2 HDMI1 Color Display PIP/PBP USB Selection Audio Energy Menu Personalize Others Resolution : 2560x1600, 60Hz 註:為防止資料受損或遺失,變更 USB 上游連接埠之前,請確 定連接螢幕 USB 上游連接埠的電腦未使用任何 USB 儲存裝置。 USB1 使用 表示 USB1 的輸入訊號。 USB2 使用 表示 USB2 的輸入訊號。 音訊 Dell UltraSharp UP3017A
功能表與子功 能表 能源 圖示 說明 Dell UltraSharp UP3017A Energy Use Brightness/Contrast Power Button LED On in On Mode Input Source USB Off in Standby Mode Color Reset Energy Display PIP/PBP USB Selection Audio Energy Menu Personalize Others Resolution : 2560x1600, 60Hz 電源按鈕 LED 可設定電源燈的狀態以節省電力。 USB 允許您在顯示器待命模式中啟用或停用 USB 功能。 註:待命模式底下的「USB 啟動/關閉(USB ON/OFF)」功能 重設電能 42 | 顯示器操作 只有在拔下 USB 上游連接線時才可以使用。插入 USB 上游連接 線時,此功能將會以灰色顯示。 選擇此選項將復原至預設的電力設定。
圖示 功能表與子功 能表 功能表設定 說明 選擇此選項以調整 OSD 設定值,例如 OSD 的語言、功能表顯 示在畫面上的持續時間等。 Dell UltraSharp UP3017A Energieverbrauch Brightness/Contrast Language Input Source Rotation Color Transparency 20 Display Timer 20 s PIP/PBP Lock Unlock USB Selection Reset Menu English Audio Energy Menu Personalize Others Resolution : 2560x1600, 60Hz 語言 旋轉 透明度 計時器 鎖定 重設功能表 設定 OSD 顯示語言,共可選擇八種語言: (英文、西班牙文、法文、德文、巴西葡萄牙文、俄文、簡體 中文、日文)。 旋轉 OSD 0/90/180/270 度。 您可以依據您的顯示旋轉調整功能表。 選擇本選項,並使用 和 (最小值 0 最大值 100)變更 功能表的透明度。 OSD 持續
功能表與子功 能表 圖示 個人化 說明 從預設模式、亮度/對比、輸入來源、長寬比、旋轉、PIP/PBP 模式、USB 選擇開關或視訊切換選擇,然後設為捷徑鍵。 Dell UltraSharp UP3017A Energy Use Brightness/Contrast Shortcut Key 1 Preset Modes Input Source Shortcut Key 2 Brightness/Contrast Color Shortcut Key 3 Input Source Display Reset Personalization PIP/PBP USB Selection Audio Energy Menu Personalize Others Resolution : 2560x1600, 60Hz 重設個人化 其他設定 將捷徑鍵設定還原成原廠預設值。 Dell UltraSharp UP3017A Energy Use Brightness/Contrast DDC/CI Input Source LCD Conditioning Disabl
圖示 功能表與子功 能表 DDC/CI 說明 您可透過 DDC/CI(顯示資料頻道 指令介面)使用電腦軟體調 整顯示器設定。 選取停用可關閉此功能。 啟用此功能將可獲得最佳的使用者體驗,並讓顯示器發揮最佳 效能。 Energy Use Dell UltraSharp UP3017A Brightness/Contrast DDC/CI Enable Input Source LCD Conditioning Disable Color Display PIP/PBP Firmware Reset Others Factory Reset USB Selection Audio Energy Menu Personalize Others Resolution : 2560x1600, 60Hz LCD 調適 可協助減少不常見的的影像殘留情況。 此程序所需的執行時間視影像殘留程度而定。選取啟用可啟動 程序。 Dell UltraSharp UP3017A Energy Use Brightness/Contrast DDC/CI Input Source LCD Condit
OSD 警告訊息 啟用動態對比功能(在這些預設模式下: 遊戲或電影)時,即停用手動亮度調整功能。 Dell UltraSharp UP3017A To allow manual adjustment of brightness, the Dynamic Contrast will be switched off. Do you want to continue? No Yes 若顯示器未支援特定解析度模式,則會出現下列訊息: Dell UltraSharp UP3017A The current input timing is not supported by the monitor display. Please change your input timing to 2560x1600, 60Hz or any other monitor listed timing as per the monitor specifications.
啟動電腦並喚醒顯示器,以進入 OSD。 若按下電源按鈕以外的任一按鈕,則會依據您所選擇的輸入來源,出現下列其中一種訊息: Dell UltraSharp UP3017A No DP signal from your device. Press any key on the keyboard or move the mouse or wake it up. If there is no display, press the monitor button again to select the correct input source. 若選擇DP或 mDP 或HDMI1, HDMI2輸入,但未連接對應的連接線,將會出現如下所示的浮 動對話方塊。 Dell UltraSharp UP3017A ? No DP Cable The display will go into Standby Mode in 4 minutes. www.dell.
在個人化功能中選擇待機模式 下開啟的 OSD 項目時,會出現以下訊息: Dell UltraSharp UP3017A Changing to this setting (without symbol) will Increase power consumption,Do you want to continue? No Yes 如果將亮度調整成高於預設值超過 75%,會出現以下訊息: Dell UltraSharp UP3017A Adjusting to this value will increase power consumption above the default level.
疑難排解 警告:開始進行此章節的任何程序前,請遵循安全說明的指示。 自我測試 您的顯示器提供自我測試功能,可檢查顯示器是否正常運作。 若已正確連接顯示器與電腦, 但畫面仍為黑暗,則請依照下列步驟執行顯示器自我測試: 1 關閉電腦與顯示器的電源。 2 拔除電腦後側的顯示器連接線。為了確保自我測試正常運作,請拔除電腦後側的數位和 類比連接線。 3 開啟顯示器電源。 若顯示器未偵測到影像訊號,且運作正常,則會在畫面上(在黑色背景上)出現浮動對話方 塊。 在自我測試模式下,電源 LED 指示燈會亮起白色。 此外,下列其中一項對話會持續在 畫面上捲動,視所選的輸入訊號而定。 Dell UltraSharp UP3017A ? No DP Cable The display will go into Standby Mode in 4 minutes. www.dell.com/support/monitors 或 Dell UltraSharp UP3017A ? No mDP Cable The display will go into Standby Mode in 4 minutes.
或 Dell UltraSharp UP3017A ? No HDMI2 Cable The display will go into Standby Mode in 4 minutes. www.dell.
一般問題 下表中的資訊,列出您可能遭遇的顯示器一般問題以及可行的解決方法: 一般症狀 遭遇的問題 可行解決方案 無影像(電源 LED 熄滅) 無畫面 • 確保影像訊號線已經正確且穩固地連接顯示器及電 腦。 • 使用其他電氣設備,確認電源插座是否正常運作。 • 確保完全按下電源按鈕。 • 確保透過輸入來源功能表,選擇正確的輸入來源。 無 影 像 電 源 無畫面或無亮度 LED 亮起 • 透過 OSD 提升亮度及對比度控制項目。 • 執行顯示器的自我測試功能,進行檢查。 • 檢查影像訊號線的接頭是否有彎曲或受損的針腳。 • 執行內建診斷。 • 確保透過輸入來源功能表,選擇正確的輸入來源。 像素遺失 LCD 螢幕出現斑 • 持續開關電源。 點 • 像素永久遺失屬於 LCD 技術的自然瑕疵。 • 如需更多有關 Dell 顯示器品質與像素原則的資訊, 請瀏覽 Dell 支援網站: http://www.dell.
一般症狀 遭遇的問題 可行解決方案 顯示器長時間顯 示同一張靜態影 像後,出現影像 殘留現象 畫面上出現靜態 影像的輕微殘影 • 將螢幕設定成在螢幕閒置幾分鐘後關閉。在 Windows 電源選項或 Mac 能源節約器設定中可以 調整這些項目。 • 此外,請使用不停變化的螢幕保護程式。 產品特定問題 特定症狀 遭遇的問題 可行解決方案 畫面影像過小 影像置中於螢 幕,但未填滿整 個可視區域 • 檢查顯示設定OSD 中的長寬比設定。 • 將顯示器重設成原廠設定。 無法使用前面板 按鈕調整顯示器 設定 螢幕未出現 OSD • 關閉顯示器電源,拔除再重新接上電源線,接著開 啟顯示器電源。 • 請檢查 OSD 選單是否被鎖住。您可按住電源鈕旁的 按鈕 6 秒鐘解開被鎖住的 OSD 選單(詳細的說明 請參考鎖住)。 按下控制鈕時無 輸入訊號 無畫面,指示燈 亮白色。 • 請檢查訊號來源。 請移動滑鼠或按下鍵盤上任一 鍵,以確定電腦不在省電模式中。 • 請檢查訊號連接線是否正確連接,如有需要請重新 插入訊號線。 • 將電腦或視訊放影機重新啟動。 畫面未填滿整個 螢幕 畫面未填滿整個 螢幕
通用串列匯排流(USB)特定問題 特定症狀 遭遇的問題 可行解決方案 USB 介面無作用 USB 周邊設備無 作用 • 確認您的顯示器電源為開啟。 • 將上載連接線重新連接至您的電腦。 • 重新連接 USB 周邊(下載連接器)。 • 關閉然後再度開啟顯示器。 • 重新啟動電腦。 • 部分 USB 裝置如外部可攜式硬碟機需要較高的電 流;直接將裝置連接至電腦系統。 超高速 USB 3.0 介面緩慢 超高速 USB 3.0 周邊設備運作緩 慢或完全無作用 • 確認您的電腦為 USB 3.0 相容。 • 部分電腦配備有 USB 3.0、USB 2.0 和 USB 1.1 連接 埠。 請確定使用正確的 USB 連接埠。 • 將上載連接線重新連接至您的電腦。 • 重新連接 USB 周邊設備(下載連接器)。 • 重新啟動電腦。 插入 USB 3.0 裝 置時,無線 USB 周邊設備將停止 運作 無線 USB 周邊裝 • 增加 USB 3.
附錄 安全指示 若顯示器的邊框會反光,請注意顯示器放置的位置,因為周圍光源及其他亮面材質對邊框造 成的反射可能會造成視覺干擾。 警告:若進行非本說明書所述之控制、調整或程序,可能會暴露於電擊、電氣危害及 或機械危害之中。 如需安全說明的資訊,請參閱安全、環境及法規資訊 (SERI)。 FCC 聲明(僅限美國)及其他法規資訊 如需 FCC 聲明及其他法規資訊,請參閱法規遵循網站 www.dell.com/regulatory_ compliance。 RoHS 聲明(僅針對台灣) 限用物質及其化學符號 單元 鉛 (Pb) 汞 (Hg) 鎘 (Cd) 六價鉻 (Cr+6) 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) 機箱/檔板/支 架 — O O O O O 電路板組件 — O O O O O FP顯示螢幕 — O O O O O 電線/連接器 — O O O O O 電源設備 — O O O O O 喇叭/麥克風 — O O O O O 配件 — O O O O O 備考1.
聯絡 Dell 美國客戶請致電 800-WWW-DELL (800-999-3355) EU 能源標章產品和產品資訊表資料庫: UP3017A: https://eprel.ec.europa.eu/qr/344915 註:若無可用的網際網路連線,則可在購買發票、裝貨單、帳單或 Dell 商品目錄上找到 聯絡資訊。 Dell 提供多種線上及電話支援與服務方式。服務適用性因國家及產品而異,且並非所有地區 皆提供所有服務。 要取得顯示器線上支援說明: 請造訪 www.dell.com/support/monitors. 關於銷售、技術支援或客服的問題,請洽詢Dell: 1 前往 www.dell.
非 Dell 電腦 在Windows Vista、Windows 7、Windows 8或Windows 8.1 中: 1 在 Windows 8 或 Windows 8.1 中選擇桌面互動磚,以切換成傳統桌面。 2 在桌面上按一下右鍵,然後按一下個人化。 3 按一下變更顯示設定。 4 按一下進階設定。 5 在視窗頂端的說明部分,識別您的繪圖控制器製造商(如 NVIDIA、ATI、Intel 等)。 6 請瀏覽繪圖卡製造商的網站,取得最新的驅動程式(例如 http://www.ATI.com 或 http://www.NVIDIA.com)。 7 安裝顯示卡的驅動程式之後,請再試一次將解析度設定為 2560 x 1600。 在Windows 10 中: 1 在桌面上按一下右鍵,然後按一下顯示器設定。 2 按一下進階顯示設定。 3 按一下顯示卡內容。 4 在視窗頂端的說明部分,識別您的繪圖控制器製造商(如 NVIDIA、ATI、Intel 等)。 5 請瀏覽繪圖卡製造商的網站,取得最新的驅動程式(例如 http://www.ATI.com 或 http://www.NVIDIA.
維護準則 連接顯示器 警告:清潔顯示器前,請將顯示器的電源線從插座拔除。 注意:清潔顯示器前,請先詳閱並遵守安全指示。 拆開包裝、清潔或搬動顯示器時,最好依照以下清單所列的指示操作: • 若要清潔防靜電螢幕,請用乾淨的軟布沾水後,稍微沾濕。 可行時,使用適合防靜電塗層 的特製螢幕清潔紙或溶液。 請勿使用含苯、稀釋劑、氨、研磨劑的清潔劑或壓縮空氣。 • 使用以溫水稍微沾濕的軟布清潔顯示器。 請勿使用任何去污劑,以免去污劑在顯示器上留 下霧狀痕跡。 • 若您拆開顯示器包裝箱時發現白色粉末,請用清潔布清除。 • 請小心搬動顯示器,因為深色系列顯示器比淺色系列顯示器更容易在刮傷後留下白色刮 痕。 • 為了維持顯示器的最佳影像品質,請使用動態變換的螢幕保護程式,並在不使用顯示器時 將電源關閉。 附錄 | 57