Dellt Network Management Card User's Guide www.dell.com | support.dell.
Notes and Warnings NOTE: A NOTE indicates important information that helps you make better use of your software. DANGER: A DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: A WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or injury.
Table of Contents 1 Introduction 2 Getting Started Unpacking the Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Card Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Card Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 UPS Weekly Schedule Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Shutdown Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 UPS Shutdown (Inverter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Load Segments Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 6 Operation and Maintenance Serial Cable Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Serial Configuration Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Option 1: Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Option 2: Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction 1 The Dellt Network Management Card works with Dell UPS Management Software to monitor, manage, and protect uninterruptible power supplies (UPSs) through standard Web pages, Simple Network Management Protocol (SNMP), and Secure Sockets Layer (SSL) security protocol. The Dell Network Management Card can support up to five connected browsers at a time, or three with SSL protocol.
S Online Help (English only) S Card firmware updated through the network S UPS firmware updated through the network S Fast Ethernet 10/100 MB compatibility with auto-negotiation on the RJ-45 port S Connection to the card with straight CAT 5 RJ-45 network cables [maximum card distance is 20m (65 ft)] S Easy installation—the Dell Network Management Card can be installed while the UPS is online, maintaining the highest system availability S Compatibility with the Internet Engineering Task Force (IETF) Manageme
Getting Started This chapter explains: S Unpacking the card S Checklist items needed for installation S Identifying the card ports and indicators S Card defaults S Installing and connecting the card S Configuring the network with a DHCP server S Configuring the network without a DHCP server Unpacking the Card Verify the package contents (see Figure 1): S Dell Network Management Card S Serial cable S Setup instructions S Safety, Environmental, and Regulatory Information Figure 1.
Installation Checklist 1 2 Verify that all of the following items are available: - Dell Network Management Card package contents - Phillips® screwdriver - Ethernet cable - Available serial port (RS-232) - HyperTerminal® (ships with Microsoft® Windows®) or equivalent terminal emulation application - Web browser (Microsoft Internet Explorer® or Mozilla® Firefox® recommended) Provide the local network administrator with the card's MAC address: - MAC Address Port: _________________________ - Th
Card Details 1 4 6 5 2 3 1. Ethernet Port (10/100BaseT) 2. ACT LED (green) 3. 100M LED (orange) 4. Settings Port 5. UPS Data LED (green) 6. RS232 LED (orange) Figure 3. Dell Network Management Card Details Table 1.
Card Defaults Table 2 lists the Dell Network Management Card default parameters. Table 2. Default Parameters Function On Parameter Default Value Possible Values Network IP Address 192.168.1.2 Network IP address Subnet Mask 255.255.0.0 Network IP address Gateway Address 0.0.0.
Installing the Card The Dell Network Management Card can be installed in any Dell UPS equipped with a communication bay without turning off the UPS or disconnecting the load. To install the Dell Network Management Card: 1 Remove the communication bay cover from the UPS. Retain the screws. 2 If not already done, record the card's MAC address for future reference (see “Installation Checklist” on page 9). 3 To prevent electrostatic discharge (ESD), place one hand on a metal surface.
3 Connect an active Ethernet cable (not supplied) to the Ethernet port on the Dell Network Management Card (see Figure 5). Wait approximately two minutes until the UPS Data LED flashes regularly, indicating normal operation. Ethernet Port Settings Port Ethernet Figure 5.
Configuring the Card To configure the card: 1 Verify that the serial cable (supplied) is connected to the card's Settings port and the computer's COM port. 2 Open your terminal emulation program (such as HyperTerminal). 3 Select the serial connection (such as COM1). 4 Set the serial line to 9600 baud, 8 data bits, No parity, 1 stop bit, no flow control (see Figure 6). Figure 6.
5 Verify that the UPS is turned on. The initialization process completes, and you are prompted enter the password (Figure 7). ------------------------------------------------------------End of Init, card is ready ... Enter password to activate Maintenance Menu : Warning: for SMTP server resolution don't forget to set DNS File RAM0/ConfigurationData.xml created with 17096 bytes File FLASH0/ConfigurationData.
Configuring the Network With a DHCP Server The card automatically collects the IP parameters from the server by default. NOTE: When the card is not connected to the network, it continuously attempts to connect. When the connection is established, the LEDs indicate the status (see Table 1 on page 10). To view the parameters: 1 From the main menu, type 2 and press Enter. The Network Settings menu displays (see Figure 9).
3 Record the IP address. 4 To exit, type 0 and press Enter; then type 0 and press Enter again. The card is now operational. Configuring the Network Without a DHCP Server To set the network configuration manually: 1 From the main menu, type 2 and press Enter. Type 2 and press Enter again to modify the network settings. The Network Settings menu displays (see Figure 11). NOTE: You cannot configure the IPv6 address through the serial link.
Testing the Configuration To verify that the Dell Network Management Card is operational: 1 Open a Web browser from a station connected to the same subnet as the card. 2 Enter the card's https://IP address (IPv4 or IPv6) in the address bar. The home page displays (see Figure 12). Figure 12. Home Page If you logged in as admin, continue to Chapter 3, “Configuring the Card,” on page 19 for additional configuration options.
3 Configuring the Card NOTE: You must be logged in as admin to configure the card.
Navigating the Card's Web Page Figure 13 shows the different areas and features of the card’s Web page. The UPS Properties page is the home page that displays after you log on to the Web interface. Link to Help Menu Bar Figure 13. Navigating the Card's Web Page The menu bar to the left of the page contains links to the card's additional pages for status information and configuration options. Menus are expandable and collapsible.
Logging In By default, the user name and password are both admin (see Figure 14). Figure 14. Login Window Both the user name and password fields accept a maximum of ten characters. After five minutes have elapsed, or if the browser is closed and reopened, you must re-enter the user name and password. An error in either field results in rejection of the requested action (such as save, page access, or card reboot). After three unsuccessful login attempts, you must restart the browser.
Online Help The Dell Network Management Card's online Help provides information on all main menu items. NOTE: The Help is in English only. To access Help: 1 Click Help. The Help page opens(see Figure 15). 2 Select a Help topic from the menu bar. The corresponding Help content displays on the right. Figure 15.
UPS Properties Essential information about the UPS status is available on the UPS Properties page (see Figure 16), which refreshes automatically every ten seconds. The UPS Properties page shows an image and generic name of the UPS. You can customize the default location Computer Room to name the location of your system (see “System Settings” on page 52). UPS Status UPS Status List Current UPS Operating Mode Diagram Figure 16.
UPS Measurements Detail Place the cursor over the diagram to display the UPS measurements detail (see Figure 17). These measurements are available for Normal mode, Battery mode, and Bypass mode. The available measurements depend on the UPS model. UPS Measurements Detail Figure 17. UPS Measurements Detail UPS Status Icons Table 3 lists the UPS status icons. Table 3.
Diagrams display examples of the UPS current operating mode (see Table 4). NOTE: If communication with the UPS is lost, all diagrams appear gray. Table 4.
Table 5 lists all the elements that can appear in a UPS operating mode diagram. Table 5.
Table 5.
Table 5.
UPS Status List Select an item from the UPS Status list to view specific information about the UPS (see Figure 18). Table 6 lists the items available. The following sections describe each item in detail. UPS Status List Figure 18. UPS Status List (Default UPS Status View Shown) Table 6.
UPS Status The UPS Status view displays the following basic information about power and output: S Power source: Indicates whether power comes from the utility or from the UPS battery. S Output load level: Indicates the power percentage used at UPS output. S Output: Indicates whether the individual UPS outputs are protected. - Inverter (UPS): Indicates whether the UPS main output is protected.
View Current Alarms Select UPS Alarms from the UPS Status list to display the list of current alarms (see Figure 19). Table 8 lists the alarm severity levels. Table 9 and Table 10 list the managed UPS and system alarms. Figure 19. UPS Alarms Display Table 8.
Table 9.
Table 9.
Table 9. UPS Alarms (continued) Alarm On Alarm Off On buck Return from buck On boost Return from boost Table 10.
View Power Consumption Select UPS Metrics from the UPS Status list to display levels of power consumption (see Figure 20) for the following: S Peak Consumption: Indicates the last peak of consumption since the last reset. S Cumulative Consumption: Indicates the consumption computed since the last reset. S Peak Headroom: Indicates the most recent peak headroom level since the last reset. The real time headroom value is shown in the diagram. You can reset the time stamp for each parameter. Figure 20.
View UPS and Card Information Select About Your UPS from the UPS Status list to display information about the UPS and the card (see Figure 21). Figure 21.
UPS Control Click UPS Control from the menu bar to open the UPS Control page (see Figure 22). Figure 22. UPS Control Page The UPS Control page enables triggering of startup and shutdown sequences for the UPS main output and load segments. The status of each output displays by a icon associated with the Off label (red icon) or On label (green icon). The shutdown sequences allow time for the registered servers to shut down without losing data (see “Shutdown Parameters” on page 40).
S Safe power down & reboot: Immediately launches a sequence to switch off and then restore output power. It shuts down the powered systems during the shutdown sequence, and then switches off the output. Finally, it launches the restart sequence at the end of the time delay specified in the Toggle duration parameter. The output status is updated. S Immediate On: Immediately launches a sequence to switch on output power . It re-powers the output and starts the systems.
UPS Weekly Schedule Programming Click Weekly Schedule from the menu bar to set up the timing of specific weekly actions (see Figure 23). Figure 23. Weekly Schedule Page NOTE: UPS configuration can prevent the shutdown and restart commands from being run properly. Refer to the UPS user's manual for more information. The weekly schedule enables the administrator to optimize power consumption or program a reboot of the protected equipment at a set time.
Shutdown Parameters Click Shutdown Parameters from the menu bar to view and configure UPS operating parameters in battery mode and for power restoration (see Figure 24). Figure 24. Shutdown Parameters Page (Advanced Parameters Shown) Click Show advanced parameters to display additional parameters for adjusting specific thresholds related to the percentage of remaining battery charge level. The Output column allows each receptacle to be named (maximum 20 characters).
UPS Shutdown (Inverter) The first shutdown criterion initiates the restart of the shutdown sequence if the remaining time is under (0 to 99999 seconds, 180 by default). This value is the minimum remaining backup time before the shutdown sequence is launched. S If battery capacity is under (0 to 100%): This value cannot be less than that of the UPS and is the minimum remaining battery capacity level before the shutdown sequence launches.
Measurements Click Measurements from the menu bar to view the measurements for the UPS (see Figure 25). Figure 25.
The save frequency of these values (60 seconds by default) is defined on the System page (see “System Settings” on page 52). Approximately 435 time-stamps can be stored on the card. When the system exceeds this threshold, the oldest time-stamps are deleted automatically. Save Log enables you to open or save all saved values in comma separated values (CSV) format (compatible with Microsoft Excel type spreadsheets). Clear Log enables you to delete all records.
The card can save up to 435 events. When this threshold is exceeded, the system deletes the oldest event when a new one occurs. Save Log enables you to save values in CSV format. Clear Log enables you to delete all records. Enter the admin user name and password to validate this action. NOTE: See Table 9 and Table 10 starting on page 32 for a list of managed alarms. System Log Click System Log from the menu bar to view system events (see Figure 27). The card can save up to 435 events.
Notification E-Mail Notification The card can redirect UPS alarms to an e-mail server to distribute information to the appropriate recipients. The format of these e-mail messages is compatible with mobile telephone transfer systems using the short message service (SMS) standard for text messaging. Click Email Notification from the menu bar to configure e-mail recipients (see Figure 28). Figure 28.
Each recipient is configured with the following parameters: S Recipient (limited to 99 characters): The e-mail address of the person or department to receive the e-mail. The default value is recipienttx@domain.com. The files are sent in CSV format. S Attached files: The files selected (Measurements, Event log, System log) are attached to the e-mail message.
E-Mail Message Settings Use the Email Message Settings page to customize the content of e-mail messages initiated by the card (see “Email Notification” on page 45). See Figure 29. Figure 29. Email Message Settings Page Common settings for all e-mail message recipients follow: S Sender (59 characters maximum): Identifies the source of the message. The default value is ups@domain.com. This field allows free text.
S Message text: Allows a maximum of 255 characters. As shown in Figure 30, the body of the e-mail message contains: - Message text - The date and time of the event, as saved in the log - URL of the card, enabling a direct link with the card to be established - Attachments, as configured for the e-mail recipients - Duplication of the subject, if configured From: ups@domain.
Network Settings Click Network from the menu bar to configure the network parameters of the card and authorize the remote upgrade of the embedded system (see Figure 31). Figure 31. Network Settings Page Configurable network settings are: S IP Address: The IP address of the card (for example, 166.99.224.70). S Subnet Mask: The mask of the sub-network of your network (for example, 255.255.255.0).
S IPv6 Enabled: When selected, Internet Protocol version 6 (IPv6) features are enabled. NOTE: IPv6 is described in the Internet standard RFC 2460. S IPv6 Auto Config Enabled: Select this option to have the following IPv6 parameters automatically generated by the card or the IPv6 DHCP server (if an IPv6 DHCP server is available on the network): - Local IPv6 address - Prefix length The IPv6 Gateway becomes unavailable and remains blank.
NOTE: If the hostname is not used, the IP address supplied by the DHCP server must be assigned through Static DHCP Assignment to maintain the connection with the clients installed on the stations to be protected. NOTE: During the first connection, if the DHCP query is not successful, the Dell Network Management Card starts with the following IP configuration: IP Address: 192.168.1.2 Subnet Mask: 255.255.255.0 Gateway Address: 0.0.0.
System Settings Click System from the menu bar to customize the information that displays on the UPS Properties page (see “UPS Properties Page” on page 23). The System Settings page opens (see Figure 32). Figure 32. System Settings Page Configurable system settings are: S UPS Contact: This text field is limited to 49 characters. Enter the name of the person responsible for UPS administration at IT network level and/or electrical maintenance. This field does not appear on any other Web page.
S Factory Reset button: Restores the default configuration of all the card's parameters. S Keep TCP/IP parameters: Select this option to maintain the IP address, subnet mask, gateway, and BOOTP/DHCP value. To ensure security, this operation requires admin user name and password. By default, user name and password are both admin.
2 Click either Modify NMS or Add NMS to open a new window where you can modify or enter SNMP trap receiver information (Application Name, Hostname or IP Address, Trap Community, and Severity). See Figure 34. Figure 34.
Access Control Click Access Control from the menu bar to configure the different parameters to allow secure access to the card using a browser or SNMP. NOTE: If you are not already logged on, you will be prompted to enter your user name and password before accessing this page. NOTE: Restart the card to activate any configuration changes. Figure 35.
S Security mode: Manages the various authentication methods for page access. The default method is SSL and full authentication. Security modes options are: - Authentication for configuration: Only the configuration pages are protected by user name and password. - Full authentication: All pages are protected by a user name and password. - SSL and full authentication: All pages are protected by user name and password and are accessible only in SSL.
Date and Time You can set the card's date and time manually or set to synchronize with the NTP server from the Setting time page (see Figure 36). Figure 36.
To set the date and time: 1 Click Time from the menu bar to open the Setting time page. 2 To manually set the date and time, select Set manually and enter values in the Date and Time fields, and click Save. Maximum drift is ±2 min/month. 3 To synchronize the time with the NTP server, select Synchronize with NTP server. Selecting this option enables a connection with a time server, available either on the company's internal network or on the Web. This server communicates GMT time.
4 MIB Objects This chapter describes the Management Information Base (MIB) files available with the card. A MIB is an information repository residing on a device in a communication network. Network management software uses a device's MIB to manage the device. Every manageable device on a network has a MIB consisting of one or more files that list information about the device.
Table 11. IETF UPS MIB Objects (continued) Variable Name and Relative XML Object Path upsEstimatedMinutesRemaining OID Variable Type Variable Unit 1.2.3 Integer Min 1.2.4 Integer % 1.2.5 Integer 0.1V 1.2.6 Integer 0.1A 1.2.7 Integer °C 1.3.1 Counter — 1.3.2 Integer — 1.3.3.1.2 Integer 0.1 Hz 1.3.3.1.3 Integer V 1.3.3.1.4 Integer 0.1 A 1.4.1 Integer — 1.4.2 Integer 0.1 Hz 1.4.3 Integer — 1.4.4.1.2 Integer V 1.4.4.1.3 Integer 0.1A 1.4.4.1.4 Integer W 1.4.4.
Table 11. IETF UPS MIB Objects (continued) Variable Name and Relative XML Object Path upsBypassNumLines OID Variable Type Variable Unit 1.5.2 Integer — 1.5.3.1.2 Integer V 1.5.3.1.3 Integer 0.1A 1.5.3.1.4 Integer W 1.6.1 Gauge — — — — 1.6.3.1 — — 1.6.3.2 — — 1.6.3.3 — — 1.6.3.4 — — 1.6.3.5 — — 1.6.3.6 — — 1.6.3.7 — — 1.6.3.8 — — 1.6.3.9 — — 1.6.3.10 — — 1.6.3.11 — — No Relative XML Object Path upsBypassVoltage UPS.PowerConverter.Input[2].
Table 11. IETF UPS MIB Objects (continued) Variable Name and Relative XML Object Path upsAlarmUpsOffAsRequested OID Variable Type Variable Unit 1.6.3.12 — — 1.6.3.13 — — 1.6.3.14 — — 1.6.3.15 — — 1.6.3.16 — — 1.6.3.17 — — 1.6.3.18 — — 1.6.3.19 — — 1.6.3.20 — — 1.6.3.21 — — 1.6.3.22 — — 1.6.3.23 — — 1.7.3 Integer {1,2,3,4,5,6} 1.8.1 Integer Sec 1.8.2 Integer Sec 1.8.3 Integer Sec Relative XML Object Path not implementated upsAlarmChargerFailed UPS.
Table 11. IETF UPS MIB Objects (continued) Variable Name and Relative XML Object Path upsConfigInputVoltage OID Variable Type Variable Unit 1.9.1 Integer V 1.9.2 Integer 0.1 Hz 1.9.3 Integer V 1.9.4 Integer 0.1 Hz 1.9.5 Integer VA 1.9.6 Integer W 1.9.7 Integer Min 1.9.8 Integer — 1.9.9 Integer V 1.9.10 Integer V UPS.Flow[1].ConfigVoltage upsConfigInputFreq UPS.Flow[1].ConfigFrequency upsConfigOutputVoltage UPS.Flow[4].ConfigVoltage upsConfigOutputFreq UPS.Flow[4].
Dell UPS MIB NOTE: Not every UPS model implements all of the Dell UPS MIB objects. For example, the bypass objects are supported only by larger UPSs with a separate bypass feed. The Dell OID is 674. The Dell UPS MIB must start at OID at 1.3.6.1.4.1.674.10902.2. The Dell UPS MIB consists of the following groups: S Product identification S Product status S Product physical Product Identification Group The name of the group is “ProductID” with a group OID of 100. See Table 12 for OID 100 group variables.
Product Status Group The name of the group is “ProductStatus” with a group OID of 110. See Table 13 for OID 110 group variables. Table 13. Product Status Group Variables Variable Name and Description productStatusGlobalStatus OID Variable Type 1 Integer 2 Integer 3 Integer 4 Integer 5 Integer 6 Integer Current status of the product. This is a roll-up for the entire product including any monitored devices.
Product Physical Group The name of the group is “Physical” with a group OID of 120. See Table 14 for OID 120 group variables. Table 14. Product Physical Group Variables Variable Name and Description physicalIdentFamilyName OID Variable Type Variable Unit 1.1 String — 1.2 String — 1.3 Integer — 2.1 Integer Watts 2.2 Integer Watts 2.3 Integer Time Stamp 2.4 Integer Watts 2.5 Integer Time Stamp UPS Family name UPS.PowerSummary.
Table 14. Product Physical Group Variables (continued) Variable Name and Description physicalOutputPresentConsumption OID Variable Type Variable Unit 2.6 Integer kWh 2.7 Integer kWh 2.8 Integer Time Stamp 2.9 Integer VA 3.1 Integer Volts 3.2 Integer Volts 4.1 Integer Time Stamp 4.2 String — Derived by averaging the watt second consumption over the past hour.
Table 14. Product Physical Group Variables (continued) Variable Name and Description physicalBatteryABMStatus OID Variable Type Variable Unit 5.1 Integer — 5.2 Integer — 5.3 Integer Seconds 6.1 Integer Seconds 6.2 Integer Seconds Advanced Battery Monitoring status: 1: ABM charging 2: ABM discharging 3: ABM floating 4: ABM resting 5: ABM off UPS.BatterySystem.Charger.
Table 14. Product Physical Group Variables (continued) Variable Name and Description physicalLoadSegment2ShutdownAfterDelay OID Variable Type Variable Unit 6.3 Integer Seconds 6.4 Integer Seconds Number of seconds remaining until Load Segment 2 switches off. -1 if no shutdown countdown is in effect. UPS.OutletSystem.Outlet[3].DelayBeforeShutdown physicalLoadSegment2StartupAfterDelay Number of seconds remaining until Load Segment 2 switches on. -1 if no startup countdown is in effect. UPS.
Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path trapBypassFrequencyOutOfRange Trap Trap Level 5 2 6 1 7 1 8 1 9 1 10 1 11 2 12 1 13 2 14 1 15 2 Bypass under or over frequency UPS.PowerConverter.Input[2].PresentStatus.FrequencyOutOfRange = 1 trapBypassFrequencyOutOfRangeOk Bypass under or over frequency ok UPS.PowerConverter.Input[2].PresentStatus.FrequencyOutOfRange = 0 trapOnBuck On Buck / Input Voltage Reducer UPS.
Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path trapInputFrequencyOutOfRangeOk Trap Trap Level 16 1 17 2 18 1 19 2 20 1 21 2 22 1 23 3 24 1 25 2 26 1 Input under or over frequency ok UPS.PowerConverter.Input[1].PresentStatus.FrequencyOutOfRange = 0 trapRemoteEmergencyPowerOff Remote emergency power off UPS.PowerSummary.PresentStatus.
Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path trapPosDCLinkUnderVoltage Trap Trap Level 27 2 28 1 29 2 30 1 31 2 32 1 33 3 34 1 35 3 36 1 37 3 Positive DC link under voltage (applies only to double-conversion models) UPS.PowerConverter.Rectifier.PresentStatus.LowPositiveDCBusVoltage = 1 trapPosDCLinkUnderVoltageOk Positive DC link under voltage ok UPS.PowerConverter.Rectifier.PresentStatus.
Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path trapChargerOk Trap Trap Level 38 1 39 3 40 1 41 3 42 1 43 3 44 1 45 3 46 1 47 2 48 1 Charger ok UPS.BatterySystem.Charger.PresentStatus.InternalFailure = 0 trapEepromFailure EEPROM failure UPS.PowerSummary.PresentStatus.ConfigurationFailure = 1 trapEepromOk EEPROM ok UPS.PowerSummary.PresentStatus.ConfigurationFailure = 0 trapShutdownImminent Shutdown imminent UPS.
Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path trapBatteryOverVoltage Trap Trap Level 49 3 50 1 51 3 52 1 53 2 54 1 57 1 58 1 59 1 60 1 61 1 Battery DC over voltage UPS.BatterySystem.Battery.PresentStatus.VoltageTooHigh = 1 trapBatteryOverVoltageOk Battery DC over voltage ok UPS.BatterySystem.Battery.PresentStatus.VoltageTooHigh = 0 trapHeatsinkOvertemperature Heatsink overtemperature UPS.PowerSummary.PresentStatus.
Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path Trap Trap Level trapBatteryTestDone (physical BatteryTestStatus) 62 1 63 3 64 1 65 3 66 1 67 3 68 1 69 3 70 1 71 2 72 2 Battery test done Variable: physicalBatteryTestStatusUPS.BatterySystem.Battery.Test ? 5 trapBatteryNeedReplacement Battery test failed, battery needs to be replaced UPS.PowerSummary.PresentStatus.
Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path trapDCLinkImbalance Trap Trap Level 73 1 74 1 79 2 80 2 81 2 82 2 83 2 84 2 85 2 86 1 87 2 DC link imbalance (applies only to double-conversion models) UPS.PowerConverter.Rectifier.PresentStatus.DCBusUnbalanced = 1 trapDCLinkImbalanceOk DC link imbalance ok UPS.PowerConverter.Rectifier.PresentStatus.
Table 15. Product Physical Group Variables (continued) Trap Name, Description, and Relative XML Object Path trapRectifierOverloadOk Trap Trap Level 88 1 89 2 90 1 91 2 92 1 93 2 Rectifier current ok UPS.PowerConverter.Rectifier.PresentStatus.OverLoad = 0 trapInverterOverload Inverter output over current UPS.PowerConverter.Inverter.PresentStatus.OverLoad = 1 trapInverterOverloadOk Inverter output current ok UPS.PowerConverter.Inverter.PresentStatus.
5 Specifications Table 16.
6 Operation and Maintenance This chapter explains: S Serial cable pinout S Detailed serial configuration menus S Firmware upgrade instructions Serial Cable Pinout Figure 37 shows the serial cable and pinout. Male RJ-45 Connector Female DB-9 Connector 2 3 5 Frame Female DB-9 Connector Shielded Cable 3 6 4 Frame Male RJ-45 Connector Figure 37. DB-9/RJ-45 Serial Cable and Pinout Serial Configuration Menus Use the supplied cable to connect the card to a computer.
3 Enter the admin password (not modifiable). The Dell Network Management Card main menu displays (see Figure 38). ------------------------------------------------------------Dell Network Management Card ------------------------------------------------------------1 : Reset 2 : Network configuration 3 : Set Login Password to Default 4 : Return to Default Configuration 0 : Exit ------------------------------------------------------------- Figure 38.
Option 2: Network Configuration The Network Configuration option displays additional options for network settings (see Figure 40): ------------------------------------------------------------Network setting ------------------------------------------------------------1 : Read Network settings 2 : Modify Network settings 3 : Set Ethernet speed 0 : Exit ------------------------------------------------------------- Figure 40.
S Modify Network settings: To modify existing network parameters (see Figure 42). Restart the card to activate the new parameters. In DHCP mode, the card can receive the following parameters according to the DHCP server settings: - IP address - Subnet mask - Gateway address NOTE: You cannot configure the IPv6 address through the serial link. The IPv6 address is provided by the card or by the IPv6 DHCP server (if an IPv6 DHCP server is available on the network).
S Set Ethernet speed: To change the network speed (see Figure 43). Restart the card to activate the new parameters. Set the Ethernet speed : [1 : Automatic, 2 : 10 MBit] 1 New Ethernet speed : Automatic Wait while the new setting is saved. Reset the card to enable the new configuration. Figure 43. Ethernet Speed Settings Option 3: Set Login Password to Default Select menu item 3 to return the password to the default (admin). Wait for the confirmation message (see Figure 44).
Option 4: Return to Default Configuration Select menu item 4 to restore the parameters to the factory-default configuration (see “Card Defaults” on page 11). Wait for the confirmation message (see Figure 45). Restart the card to save the default parameters. Configuration has been set to default one. You must Reset the card. Figure 45.
Upgrading the Card's Firmware You can update the card’s firmware by downloading the appropriate file. During the upgrade process, the Dell Network Management Card does not monitor the UPS status. To upgrade the firmware: 1 Download the new firmware version to your computer from the Web and note the location. NOTE: Go to dell.support.com for more information on downloading firmware. 2 Click Firmware Upload from the menu bar to open the Firmware Upload page (see Figure 46). Figure 46.
3 Click Browse to go to the firmware location and select the file to be loaded. 4 Click Upload. NOTE: The upload can take up to five minutes. Do not interrupt the operation before the card displays confirmation that the firmware upload was successful (Figure 47). Figure 47.
7 Shutdown Criteria and Sequence This chapter explains: S Shutdown criteria managed by the card S The shutdown sequence S Load segments Shutdown Criteria Managed by the Card During an extended power failure, three criteria can cause the server shutdown procedure to be initiated. If multiple criteria are selected, the first criterion encountered launches the shutdown procedure. See Table 17 for criteria descriptions.
Shutdown Sequence At the end of the shutdown procedure, when all servers have been shut down, the UPS itself may shut down to avoid unnecessary discharge of its batteries, depending on its configuration. See Figure 48 for the shutdown sequence.