Dell Vostro 1540/1550 사용 설명서 규정 모델 P18F 규정 유형 P18F001,P18F002
주, 주의 및 경고 노트: 주는 컴퓨터를 보다 효율적으로 사용하는 데 도움을 주는 중요 정보를 제공합 니다. 주의: 주의는 지침을 준수하지 않으면 하드웨어 손상이나 데이터 손실의 위험이 있 음을 알려줍니다. 경고: 경고는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험이 있음 을 알려줍니다. 본 발행물에 수록된 정보는 사전 통보 없이 변경될 수 있습니다. © 2011 Dell Inc. 저작권 본사 소유. Dell Inc.의 서면 승인 없이 어떠한 방식으로든 본 자료를 무단 복제하는 행위는 엄격히 금지됩니다. 본 택스트에 사용된 상표: Dell™, DELL 로고, Dell Precision™, Precision ON™,ExpressCharge™, Latitude™, Latitude ON™, OptiPlex™, Vostro™, 및 Wi-Fi Catcher™는 Dell Inc.의 상표입니다.
목차 주, 주의 및 경고...........................................................................................2 장 1: 컴퓨터 내부 작업...............................................................................7 컴퓨터 내부 작업을 시작하기 전에..............................................................................7 권장 도구..........................................................................................................................9 컴퓨터 끄기..............................................................................
장 10: 하드 드라이브 분리......................................................................29 하드 드라이브 장착.......................................................................................................30 장 11: WLAN(무선 근거리 통신망) 카드 분리....................................31 WLAN(무선 근거리 통신망) 카드 장착........................................................................32 장 12: 코인 셀 배터리 분리.....................................................................33 코인 셀 배터리 장착.........................................
장 22: 카메라 분리.....................................................................................61 카메라 장착....................................................................................................................62 장 23: 디스플레이 패널 분리..................................................................63 디스플레이 패널 장착..................................................................................................65 장 24: 저전압 차동 신호(LVDS) 케이블 분리......................................
1 컴퓨터 내부 작업 컴퓨터 내부 작업을 시작하기 전에 컴퓨터의 잠재적 손상을 방지하고 안전하게 작업하기 위해 다음 안전 지침 을 따르십시오. 특별히 언급하지 않는 한 이 설명서에 포함된 각 절차의 전 제 조건은 다음과 같습니다. • • • 컴퓨터 내부 작업의 단계를 수행했습니다. 컴퓨터와 함께 제공된 안전 정보를 읽었습니다. 분리 절차를 역순으로 수행하여 구성 요소를 교체하거나 설치(별도로 구입한 경우)할 수 있습니다. 경고: 컴퓨터의 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보 를 반드시 읽고 숙지하십시오. 추가적인 안전에 관한 모범 사례 정보에 대해 서는 법적 규제 준수 홈 페이지(www.dell.com/regulatory_compliance)를 참조하 십시오. 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니 다.
주의: 케이블을 분리할 때는 케이블을 직접 잡아 당기지 말고 커넥터나 당김 탭을 잡고 분리합니다. 일부 케이블에는 잠금 탭이 있는 커넥터가 달려 있으 므로 이와 같은 종류의 케이블을 분리하는 경우에는 잠금 탭을 누르고 분리합 니다. 커넥터를 잡아 당길 때 커넥터 핀이 구부러지지 않도록 수평으로 잡아 당깁니다. 케이블을 연결하기 전에 두 커넥터가 방향이 올바르게 정렬되었는 지도 확인합니다. 노트: 컴퓨터와 특정 구성 부품의 색상은 이 설명서와 다를 수도 있습니다. 컴퓨터의 손상을 방지하기 위해, 컴퓨터 내부 작업을 시작하기 전에 다음 단계를 수행하십시오. 1. 컴퓨터 덮개의 긁힘을 방지하기 위해 작업대 표면이 평평하고 깨끗한 지 확인합니다. 2. 컴퓨터를 끕니다(컴퓨터 끄기 참조). 3. 컴퓨터가 선택 사항인 미디어 베이스 또는 배터리 슬라이스와 같은 도 킹 장치에 연결되어 있는 경우(도킹된 상태) 도킹을 해제합니다.
권장 도구 이 문서의 절차를 수행하기 위해 다음 도구가 필요할 수 있습니다. • • • • • 소형 일자 드라이버 #0 십자 드라이버 #1 십자 드라이버 소형 플라스틱 스크라이브 플래시 BIOS 업데이트 프로그램 CD 컴퓨터 끄기 주의: 데이터 손실을 방지하기 위해, 컴퓨터를 끄기 전에 열린 파일을 모두 저 장한 후 닫고 열린 프로그램을 모두 종료하십시오. 1. 다음과 같이 운영체제를 종료하십시오. • Windows Vista 의 경우: 시작 을 클릭하고 아래에 설명된 대로 시작 메뉴의 오른쪽 하단 모서리에 있는 화살표를 클릭한 다음 시스템 종료를 클릭합니다. • 2. Windows XP 의 경우: 시작 → 컴퓨터 끄기 → 끄기를 클릭합니다. 운영체제 종료 프로세 스가 완료되면 컴퓨터가 꺼집니다. 컴퓨터 및 연결된 모든 장치의 전원이 꺼져 있는지 확인합니다. 운영체 제를 종료할 때 컴퓨터 및 연결된 장치의 전원이 자동으로 꺼지지 않으 면 전원 버튼을 4 초 정도 눌러 끕니다.
1. 2. 포트 복제기, 배터리 슬라이스 또는 미디어 베이스와 같은 외부 장치를 연결하고 Express 카드와 같은 카드를 장착합니다. 컴퓨터에 전화선 또는 네트워크 케이블을 연결합니다. 주의: 네트워크 케이블을 연결하려면, 먼저 케이블을 네트워크 장치에 꽂은 다음 컴퓨터에 꽂습니다. 3. 4. 5. 10 배터리를 끼웁니다. 전원 콘센트에 컴퓨터와 연결된 모든 장치를 연결합니다. 컴퓨터 전원을 켭니다.
2 배터리 분리 1. 2. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 분리 래치를 밀어서 배터리 잠금을 해제합니다. 3. 배터리를 밀어서 컴퓨터에서 꺼냅니다.
배터리 장착 1. 딸깍 소리를 내며 제자리에 끼워질 때까지 배터리를 해당 슬롯에 밀어 넣습니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
SD 카드 분리 1. 2. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. SD 메모리 카드를 눌러 컴퓨터에서 분리합니다. 3. 컴퓨터에서 메모리 카드를 밀어서 빼냅니다.
SD 카드 장착 1. 딸각 소리를 내면서 완전히 끼워질 때까지 메모리 카드를 해당 칸으로 밉니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
4 힌지 덮개 분리 1. 2. 3. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 배터리를 분리합니다. 힌지 덮개를 고정시키는 나사를 제거합니다. 4. 컴퓨터를 뒤집고 힌지 덮개를 분리합니다.
힌지 덮개 장착 1. 2. 3. 4. 16 힌지 덮개를 장착한 후 눌러서 연결부를 컴퓨터에 고정시킵니다. 컴퓨터를 뒤집고 힌지 덮개를 고정시키는 나사를 끼웁니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
5 키보드 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 2. 배터리를 분리합니다. 3. 키보드를 컴퓨터에 고정시키는 상단의 스냅 네 개를 살짝 들어 해제합 니다. 4. 키보드를 뒤집어 손목 받침대에 놓습니다. 5. 시스템 보드에서 키보드 케이블을 분리합니다.
6. 컴퓨터에서 키보드를 분리합니다. 키보드 장착 1. 2. 3. 4. 5. 18 키보드 케이블을 시스템 보드에 연결합니다. 키보드를 30 도 기울여 해당 컴파트먼트에 삽입합니다. 키보드를 눌러 상단 스냅을 고정시킵니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
6 광학 디스크 드라이브 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 2. 배터리를 분리합니다. 3. 키보드를 분리합니다. 4. 광학 드라이브를 고정시키는 나사를 제거합니다. 5. 드라이버로 광학 드라이브를 살짝 들어 올려 컴퓨터에서 빼냅니다.
광학 디스크 드라이브 장착 1. 2. 3. 4. 5. 20 섀시 왼쪽의 케이스에 광학 드라이브를 밀어 넣습니다. 나사를 조여 광학 드라이브를 컴퓨터에 고정시킵니다. 키보드를 장착합니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
7 메모리 모듈 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 2. 배터리를 분리합니다. 3. 키보드를 분리합니다. 4. 튀어나올 때까지 메모리 모듈에서 고정 클립을 들어 올립니다. 5. 컴퓨터에서 메모리 모듈을 분리합니다.
메모리 모듈 장착 1. 2. 3. 4. 5. 22 메모리 모듈을 메모리 소켓에 삽입합니다. 고정 클립이 메모리 모듈을 제자리에 고정시킬 때까지 메모리 모듈을 아래로 누릅니다. 키보드를 장착합니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
8 손목 받침대 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 2. 배터리를 분리합니다. 3. 키보드를 분리합니다. 4. 아래쪽 베이스를 고정시키는 나사를 제거합니다. 5. 컴퓨터를 뒤집고 전원 버튼 보드 케이블(1)과 터치패드 케이블(2)을 분 리합니다.
6. 손목 받침대를 컴퓨터에 고정시키는 나사를 제거합니다. 7. 플라스틱 스크라이브를 사용하여 손목 받침대를 살짝 들어 손목 받침 대의 하단, 왼쪽 및 오른쪽 스냅이 모두 본체에서 떨어지게 합니다. 스 냅이 모두 본체에서 떨어지면 손목 받침대를 컴퓨터에서 들어 올려 제 거합니다. 손목 받침대 장착 1. 디스플레이 화면쪽으로 손목 받침대를 30 도 기울여 삽입합니다. 2. 손목 받침대를 제자리에 맞춰 조정한 후 눌러서 모든 스냅을 고정시킵 니다. 3. 전원 보드 케이블과 터치패드 케이블을 해당 커넥터에 연결합니다. 4. 손목 받침대를 컴퓨터에 고정시키는 나사를 끼웁니다. 5. 컴퓨터를 뒤집고 하단 베이스를 고정시키는 나사를 끼웁니다.
6. 7. 8. 키보드를 장착합니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
9 전원 버튼 보드 분리 1. 2. 3. 4. 5. 6. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 배터리를 분리합니다. 키보드를 분리합니다. 손목 받침대를 분리합니다. 손목 받침대에 부착시키는 접착부에서 전원 버튼 보드 케이블을 떼어 냅니다. 손목 받침대를 뒤집고 전원 버튼 보드를 손목 받침대에 고정시키는 나 사를 제거합니다.
7. 전원 버튼 보드를 들어 올린 후 구멍을 통해 전원 버튼 보드 케이블을 빼냅니다. 전원 버튼 보드 장착 1. 전원 버튼 보드 케이블을 구멍에 끼웁니다. 2. 전원 버튼 보드를 해당 칸에 고정시킵니다. 3. 나사를 끼워 전원 버튼 보드를 고정시킵니다. 4. 컴퓨터를 뒤집고 전원 버튼 보드 케이블을 손목 받침대에 부착합니다. 5. 손목 받침대를 장착합니다. 6. 키보드를 장착합니다. 7. 배터리를 끼웁니다. 8. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
10 하드 드라이브 분리 1. 2. 3. 4. 5. 6. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 배터리를 분리합니다. 키보드를 분리합니다. 손목 받침대를 분리합니다. 하드 드라이브를 밀고 들어 올려 컴퓨터에서 꺼냅니다. 하드 드라이브 브래킷을 고정시키는 나사를 제거한 후 브래킷을 하드 드라이브에서 빼냅니다.
하드 드라이브 장착 1. 2. 3. 4. 5. 6. 7. 30 하드 드라이브 브래킷을 하드 드라이브에 장착합니다. 하드 드라이브 브래킷을 고정시키는 나사를 조입니다. 하드 드라이브를 해당 칸에 넣고 SATA 커넥터쪽으로 밀어 시스템 보 드에 고정시킵니다. 손목 받침대를 장착합니다. 키보드를 장착합니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
11 WLAN(무선 근거리 통신망) 카드 분리 1. 2. 3. 4. 5. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 배터리를 분리합니다. 키보드를 분리합니다. 손목 받침대를 분리합니다. WLAN 카드에 연결된 안테나를 분리합니다. 6. 래치를 살짝 들어 해당 칸에서 WLAN 카드가 떨어지게 합니다.
7. 컴퓨터에서 WLAN 카드를 분리합니다. WLAN(무선 근거리 통신망) 카드 장착 1. WLAN 카드를 해당 슬롯에 밀어 넣습니다. 2. WLAN 카드를 래치에 끼워 제자리에 고정시킵니다. 3. WLAN 카드의 컬러 코드에 따라 안테나를 연결합니다. 4. 손목 받침대를 장착합니다. 5. 키보드를 장착합니다. 6. 배터리를 끼웁니다. 7. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
12 코인 셀 배터리 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 2. 배터리를 분리합니다. 3. 키보드를 분리합니다. 4. 손목 받침대를 분리합니다. 5. 시스템 보드에서 코인 셀 배터리 케이블을 분리합니다. 6. 컴퓨터에서 코인 셀 배터리를 분리합니다.
코인 셀 배터리 장착 1. 2. 3. 4. 5. 6. 34 코인 셀 배터리를 코인 셀 배터리 칸에 끼웁니다. 시스템 보드에 코인 셀 배터리 케이블을 연결합니다. 손목 받침대를 장착합니다. 키보드를 장착합니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
USB 보드 분리 1. 2. 3. 4. 5. 6. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 배터리를 분리합니다. 키보드를 분리합니다. 광학 드라이브를 분리합니다. 손목 받침대를 분리합니다. USB 보드 케이블을 시스템 보드에서 분리합니다. 7. USB 보드를 고정시키는 나사를 제거합니다.
8. USB 보드를 들어 올리고 컴퓨터에서 분리합니다. USB 보드 장착 1. USB 보드를 컴퓨터의 해당 칸에 삽입해서 맞춥니다. 2. USB 보드를 제자리에 고정시키는 나사를 끼웁니다. 3. USB 보드 케이블을 시스템 보드에 연결합니다. 4. 손목 받침대를 장착합니다. 5. 광학 드라이브를 장착합니다. 6. 키보드를 장착합니다. 7. 배터리를 끼웁니다. 8. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
14 마이크 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 2. 배터리를 분리합니다. 3. 키보드를 분리합니다. 4. 손목 받침대를 분리합니다. 5. 시스템 보드에서 마이크 케이블을 분리합니다. 6. 마이크를 해당 컴파트먼트에서 들어 올려 분리합니다.
마이크 장착 1. 2. 3. 4. 5. 6. 38 마이크를 해당 컴파트먼트에 끼워서 맞춥니다. 마이크 케이블을 시스템 보드에 연결합니다. 손목 받침대를 장착합니다. 키보드를 장착합니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
15 CPU 팬 어셈블리와 방열판 분리 1. 2. 3. 4. 5. 6. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 배터리를 분리합니다. 키보드를 분리합니다. 손목 받침대를 분리합니다. 시스템 보드에서 CPU 팬 케이블을 분리합니다. 그림에 나온 순서에 따라 방열판과 CPU 팬 어셈블리를 고정시키는 캡 티브 나사를 제거합니다.
7. 방열판과 CPU 팬 어셈블리를 컴퓨터에서 분리합니다. CPU 팬 어셈블리와 방열판 장착 1. 방열판과 CPU 팬 어셈블리를 제자리에 맞춥니다. 2. 캡티브 나사를 조여 방열판과 CPU 팬 어셈블리를 고정시킵니다. 3. CPU 팬 케이블을 시스템 보드에 연결합니다. 4. 손목 받침대를 장착합니다. 5. 키보드를 장착합니다. 6. 배터리를 끼웁니다. 7. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
16 프로세서 분리 1. 2. 3. 4. 5. 6. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 배터리를 분리합니다. 키보드를 분리합니다. 손목 받침대를 분리합니다. CPU 팬 어셈블리 및 방열판을 분리합니다. 프로세서 캠 나사를 시계 반대 방향으로 돌립니다. 7. 프로세서를 들어 올려 컴퓨터에서 분리합니다.
프로세서 장착 1. 2. 3. 4. 5. 6. 7. 42 프로세서를 프로세서 소켓에 삽입합니다. 프로세서가 제대로 장착되 었는지 확인하십시오. 캠 나사를 시계 방향으로 잠김 위치까지 조입니다. CPU 팬 어셈블리와 방열판을 장착합니다. 손목 받침대를 장착합니다. 키보드를 장착합니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
17 시스템 보드 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 2. 배터리를 분리합니다. 3. SD 메모리 카드를 분리합니다. 4. 키보드를 분리합니다. 5. 광학 드라이브를 분리합니다. 6. 메모리 모듈을 분리합니다. 7. 손목 받침대를 분리합니다. 8. 하드 드라이브를 분리합니다. 9. WLAN 카드를 분리합니다. 10. CPU 팬 어셈블리 및 방열판을 분리합니다. 11. 디스플레이 케이블(1), DC 입력 케이블(2), USB 보드 케이블(3), 스피커 케이블(4), 오디오 보드 케이블(5) 및 코인 셀 배터리 케이블(6)을 분리합 니다. 12. 시스템 보드를 고정시키는 나사를 제거합니다.
13. 시스템 보드를 비스듬히 들어 올린 후 LAN, VGA, HDMI 및 USB 소켓에 서 밀어 빼냅니다. 시스템 보드 장착 1. LAN, VGA, HDMI 및 USB 커넥터를 해당 소켓에 삽입하고 시스템 보드 를 제자리에 맞춥니다. 2. 시스템 보드를 제자리에 고정시키는 나사를 끼웁니다. 3. LCD 케이블, DC 입력 케이블, USB 보드 케이블, 오디오 보드 케이블, 코 인 셀 배터리 케이블 및 스피커 케이블을 연결합니다. 4. 프로세서를 장착합니다. CPU 팬 어셈블리 및 방열판을 장착합니다. WLAN 카드를 장착합니다. 하드 드라이브를 장착합니다. 5. 6. 7.
8. 9. 10. 11. 12. 13. 14. 손목 받침대를 장착합니다. 메모리 모듈을 장착합니다. 광학 드라이브를 장착합니다. 키보드를 장착합니다. SD 메모리 카드를 끼웁니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
18 스피커 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 2. 배터리를 분리합니다. 3. SD 메모리 카드를 분리합니다. 4. 키보드를 분리합니다. 5. 광학 드라이브를 분리합니다. 6. 메모리 모듈을 분리합니다. 7. 손목 받침대를 분리합니다. 8. 하드 드라이브를 분리합니다. 9. WLAN 카드를 분리합니다. 10. CPU 팬 어셈블리 및 방열판을 분리합니다. 11. 시스템 보드를 분리합니다. 12. 라우팅 채널에서 스피커 케이블을 분리합니다. 13. 고정 래치를 누르고 왼쪽 스피커를 들어 올립니다.
14. 고정 래치를 누르고 오른쪽 스피커를 들어 올립니다. 15. 스피커 어셈블리와 스피커 케이블을 컴퓨터에서 분리합니다.
스피커 장착 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 왼쪽 및 오른쪽 스피커를 해당 칸에 삽입해서 부착합니다. 스피커 케이블을 섀시에 맞춰서 배선합니다. 시스템 보드를 장착합니다. 프로세서를 장착합니다. CPU 팬 어셈블리 및 방열판을 장착합니다. WLAN 카드를 장착합니다. 하드 드라이브를 장착합니다. 손목 받침대를 장착합니다. 메모리 모듈을 장착합니다. 광학 드라이브를 장착합니다. 키보드를 장착합니다. SD 메모리 카드를 끼웁니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
19 디스플레이 어셈블리 분리 1. 2. 3. 4. 5. 6. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 배터리를 분리합니다. 힌지 덮개를 분리합니다. 키보드를 분리합니다. 손목 받침대를 분리합니다. 시스템 보드에서 LVDS 케이블을 분리합니다. 7. WLAN 안테나를 분리하고 섀시의 라우팅 채널에서 떨어뜨립니다.
8. 왼쪽 및 오른쪽 힌지를 고정시키는 나사를 제거합니다. 9. 디스플레이 어셈블리를 들어 올려 컴퓨터에서 분리합니다.
디스플레이 어셈블리 장착 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 디스플레이 어셈블리 힌지를 해당 홀더에 삽입합니다. 힌지를 제자리에 고정시키는 나사를 끼웁니다. LVDS 케이블을 시스템 보드에 연결합니다. WLAN 안테나 라우팅 케이블을 홀더에 맞추고 안테나를 WLAN 카드에 연결합니다. USB 보드 케이블을 연결합니다. 손목 받침대를 장착합니다. 키보드를 장착합니다. 힌지 덮개를 장착합니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
DC 입력 포트 및 브래킷 분리 1. 2. 3. 4. 5. 6. 7. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 배터리를 분리합니다. 힌지 덮개를 분리합니다. 키보드를 분리합니다. 손목 받침대를 분리합니다. 디스플레이 어셈블리를 분리합니다. 시스템 보드에서 DC 입력 케이블을 분리합니다. 8. DC 입력 포트 및 브래킷을 고정시키는 나사를 제거합니다.
9. DC 입력 포트 브래킷을 들어 올립니다. 10. DC 입력 포트를 컴퓨터에서 들어 올려 분리합니다.
DC 입력 포트 및 브래킷 장착 1. 2. 3. 4. 5. 6. 7. 8. 9. DC 입력 포트 및 브래킷을 해당 컴파트먼트에 끼웁니다. 브래킷을 맞추고 브래킷을 DC 입력 포트에 고정시키는 나사를 조입니 다. DC 입력 케이블을 시스템 보드에 연결합니다. 디스플레이 어셈블리를 장착합니다. 손목 받침대를 장착합니다. 키보드를 장착합니다. 힌지 덮개를 장착합니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
21 디스플레이 베젤 분리 1. 2. 3. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 배터리를 분리합니다. 아래쪽부터 시작하여, 베젤 내부를 들어 디스플레이 어셈블리에서 빼 내고 디스플레이 베젤의 오른쪽 및 왼쪽 모서리에 대해서도 마찬가지 로 작업합니다. 4. 모든 스냅이 느슨해지면 디스플레이 어셈블리에서 베젤을 분리합니 다.
디스플레이 베젤 장착 1. 2. 3. 4. 60 디스플레이 베젤을 상단 덮개에 맞춰 정렬합니다. 하단 가장자리부터 시작해서 디스플레이 베젤을 아래쪽으로 눌러 탭 을 맞물립니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
22 카메라 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 2. 배터리를 분리합니다. 3. 디스플레이 베젤을 분리합니다. 4. 카메라 모듈에서 카메라 케이블을 분리합니다. 5. 래치를 살짝 들어 카메라를 들어 올린 후 제거합니다.
카메라 장착 1. 2. 3. 4. 5. 62 카메라 모듈을 해당 컴파트먼트에 끼워서 맞춥니다. 카메라 케이블을 카메라 모듈에 연결합니다. 디스플레이 베젤을 장착합니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
23 디스플레이 패널 분리 1. 2. 3. 4. 5. 6. 7. 8. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 배터리를 분리합니다. 힌지 덮개를 분리합니다. 키보드를 분리합니다. 손목 받침대를 분리합니다. 디스플레이 어셈블리를 분리합니다. 디스플레이 베젤을 분리합니다. 카메라 모듈에서 카메라 케이블을 분리합니다. 9. 디스플레이 브래킷과 힌지를 고정시키는 나사를 제거합니다.
10. 오른쪽 힌지에서 무선 안테나를 분리합니다. 11. 왼쪽 힌지에서 LVDS 케이블을 분리합니다.
12. 디스플레이 패널과 브래킷을 들어 올려 디스플레이 상단 덮개에서 분 리합니다. 13. 왼쪽 및 오른쪽 디스플레이 브래킷의 나사를 제거하고 디스플레이 패 널을 분리합니다. 디스플레이 패널 장착 1. 왼쪽 및 오른쪽 브래킷을 디스플레이 패널에 연결하고 나사를 조입니 다. 2. 디스플레이 케이블과 무선 안테나를 왼쪽 및 오른쪽 힌지에 삽입해서 배선합니다. 3. 디스플레이 패널을 상단 덮개의 브래킷에 맞춰 정렬합니다. 4. WLAN 안테나 라우팅 케이블을 홀더에 맞추고 안테나를 WLAN 카드에 연결합니다.
5. 6. 7. 8. 9. 10. 11. 12. 13. 66 디스플레이 패널과 브래킷을 고정시키는 나사를 끼웁니다. 카메라 케이블을 카메라 모듈에 연결합니다. 디스플레이 베젤을 장착합니다. 디스플레이 어셈블리를 장착합니다. 손목 받침대를 장착합니다. 키보드를 장착합니다. 힌지 덮개를 장착합니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
24 저전압 차동 신호(LVDS) 케이블 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따르십시오. 2. 배터리를 분리합니다. 3. 힌지 덮개를 분리합니다. 4. 키보드를 분리합니다. 5. 광학 드라이브를 분리합니다. 6. 손목 받침대를 분리합니다. 7. 디스플레이 어셈블리를 분리합니다. 8. 디스플레이 베젤을 분리합니다. 9. 디스플레이 패널을 분리합니다. 10. LVDS 케이블 연결을 고정시키는 테이프를 떼어냅니다. 11. 디스플레이 패널에서 LVDS 케이블을 분리합니다.
12. 디스플레이 패널에 부착시키는 접착부에서 전체 디스플레이 케이블 을 떼어냅니다. 저전압 차동 신호(LVDS) 케이블 장착 1. 디스플레이 케이블을 디스플레이 패널에 부착합니다. 2. 디스플레이 케이블 커넥터를 디스플레이 패널에 연결하고 테이프를 붙여 고정시킵니다. 3. 디스플레이 패널을 장착합니다. 4. 디스플레이 베젤을 장착합니다. 5. 디스플레이 어셈블리를 장착합니다. 6. 손목 받침대를 장착합니다. 7. 광학 드라이브를 장착합니다.
8. 9. 10. 11. 키보드를 장착합니다. 힌지 덮개를 장착합니다. 배터리를 끼웁니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
25 시스템 설정 시작 1. 컴퓨터를 켜거나 다시 시작합니다. 2. 파란색 DELL 로고가 표시되면 F2 프롬프트가 나타나는지 보십시오. 3. F2 프롬프트가 나타나면 키를 즉시 누릅니다. 노트: F2 프롬프트는 키보드가 초기화되었다는 것을 나타냅니다. 이 프롬프트 는 빠르게 나타났다 사라지므로 표시되는지 잘 지켜보다 나타나면 곧바로 키를 누르십시오. 프롬프트가 표시되기 전에 키를 누르면 이 키입력 값을 잃게 됩니다. 4. 운영체제 로고가 나타나는 데 시간이 오래 소요되면 Microsoft Windows 바탕 화면이 나타날 때까지 기다렸다가 컴퓨터를 종료하고 다시 시도하십시오. 시스템 설정 개요 시스템 설정을 사용하여 다음과 같은 작업을 할 수 있습니다.
옵션 System Setup(시스템 설정) 창 상단에 나타납니다. 이 필드는 시스템 설정 목록 옵션에 액세스할 수 있는 메뉴를 제공합니다. 탐색하려면 <왼쪽 화살표> 와 <오른쪽 화살표>를 누릅니다. Menu(메뉴) 옵션이 강조 표시되면 Options List(옵션 목록)에 컴퓨터에 설치된 하드웨어를 정의하는 옵션이 표시됩니 다. 옵션 Options List(옵션 목록)의 오른쪽에 나타나며 Options List(옵션 목록)에 나온 필드 각 옵션에 대한 정보를 포함합니다. 이 필드에서는 컴퓨터에 대한 정보를 보고 현재 설정을 변경할 수 있습니다. 현재 설정을 변경하려면 < Enter>를 누르고 Options List(옵션 목록)로 돌아가려면 를 누르십시오. 노트: Options Field(옵션 필드)에 나열된 일부 설정은 변경할 수 없습니 다. 도움 시스템 설정 창의 오른쪽에 나타나며 Options List(옵션 목록)에서 선택한 말 옵션에 대한 도움말 정보가 포함되어 있습니다.
System Date(시스템 날짜) 컴퓨터의 내부 달력 날짜를 재설정합니 다. System Time(시스템 시간) 컴퓨터의 내부 클럭 시간을 재설정합니 다. BIOS Version(BIOS 버전) BIOS 개정 번호를 표시합니다. Product Name(제품명) 제품 이름과 모델 번호를 표시합니다. Service Tag(서비스 태그) 컴퓨터의 서비스 태그를 표시합니다. Asset Tag(자산 태그) 컴퓨터의 자산 태그를 표시합니다(사용 가능한 경우). CPU Type(CPU 유형) 프로세서의 유형을 표시합니다. CPU Speed(CPU 속도) 프로세서의 속도를 표시합니다. CPU ID 프로세서 ID 를 표시합니다. L1 Cache Size(L1 캐시 크기) 프로세서 L1 캐시 크기를 표시합니다. L2 Cache Size(L2 캐시 크기) 프로세서 L2 캐시 크기를 표시합니다. L3 Cache Size(L3 캐시 크기) 프로세서 L3 캐시 크기를 표시합니다.
Integrated NIC(통합 NIC) 온보드 네트워크 카드에 대한 전원 공급을 활성화 또는 비활성화합니다. 기본값: Enabled(사용) USB Emulation(USB 에뮬 레이션) USB 에뮬레이션 기능을 활성화 또는 비활성화합 니다. 기본값: Enabled(사용) USB Wake Support(USB 재 USB 장치가 컴퓨터를 대 기본값: Disabled(사용 안 개 지원) 기 모드에서 깨울 수 있습 함) 니다. 이 기능은 AC 어댑 터가 연결된 경우에만 활 성화됩니다. SATA Operation(SATA 작 동) SATA 컨트롤러 모드를 ATA 또는 AHCI 로 변경합 니다. 기본값: AHCI Adapter Warnings(어댑터 경고) 어댑터 경고를 활성화 또 는 비활성화합니다. 기본값: Enabled(사용) Function Key Behavior(기 능 키 동작) 기능 키 의 동작을 지 정합니다.
암호와 내장형 HDD 암호를 생략할 수 있습니다. Computrace(컴퓨트레이스) 컴퓨터에서 Computrace 기능을 활성화 또는 비활성화합니다. Boot(부팅) Boot Priority Order(부팅 우선 순위) 컴퓨터가 시작 시 부팅할 장치의 순서를 지정합니다. Hard Disk Drives(하드 디스크 드라이브) 컴퓨터가 부팅에 사용할 하드 드라이브 를 지정합니다. USB Storage Device(USB 저장 장치) 컴퓨터가 부팅에 사용할 USB 저장 장치 를 지정합니다. CD/DVD ROM Drives(CD/DVD ROM 드라 이브) 컴퓨터가 부팅에 사용할 CD/DVD 를 지 정합니다. Network(네트워크) 컴퓨터가 부팅에 사용할 네트워크 장치 를 지정합니다. Exit(종료) 이 섹션에서는 시스템 설정을 나가기 전에 기본 설정을 저장, 삭제 및 로드 할 수 있습니다.
26 진단 경고음 코드 디스플레이에 오류 또는 문제를 표시할 수 없는 경우에는 컴퓨터가 시작 도중 일련의 경고음을 울릴 수 있습니다. 경고음 코드라고 하는 이러한 일 련의 경고음은 다양한 문제를 알려줍니다. 각 경고음 사이 시간 길이는 300 밀리초이고, 각 경고음 세트 간 시간 길이는 3 초이며, 경고음은 300 밀리초 동안 울립니다. 각 경고음과 경고음 세트 후 BIOS 는 사용자가 전원 버튼을 눌렀는지 감지합니다. 사용자가 전원 버튼을 누른 게 감지되면 BIOS 는 경 고음을 중단하고 정상적인 셧다운 절차를 실행하고 시스템 전원을 켭니다.
배터리 상태 표시등 컴퓨터가 전원 콘센트에 연결되어 있는 경우, 배터리 표시등은 다음과 같 이 동작합니다. • • • • • 주황색 및 흰색 표시등이 번갈아 깜박임 — 해당 노트북 컴퓨터에 인증 되지 않았거나 지원되지 않는 비 Dell AC 어댑터가 연결되어 있습니다. 흰색 표시등이 켜져 있는 상태에서 주황색 표시등이 깜박임 — AC 어댑 터를 사용하는 상태에서 임시 배터리 오류가 발생했습니다. 주황색 표시등이 지속적으로 깜박임 — AC 어댑터를 사용하는 상태에 서 심각한 배터리 오류가 발생했습니다. 꺼짐 — AC 어댑터를 사용하는 상태에서 배터리가 완전 충전 모드에 있 습니다. 흰색 표시등 켜짐 — AC 어댑터를 사용하는 상태에서 배터리가 충전 모 드에 있습니다. 장치 상태 표시등 컴퓨터가 켜질 때 켜지고 컴퓨터가 전원 관리 모드이면 깜박입니다. 컴퓨터가 데이터를 읽거나 쓸 때 켜집니다. 배터리 충전 상태를 나타내기 위해 계속 켜져 있거나 깜박입니다. 무선 네트워킹이 활성화될 때 켜집니다.
27 사양 노트: 제공되는 제품은 지역에 따라 다를 수 있습니다. 다음은 현지 법률에 따 라 컴퓨터와 함께 제공되어야 하는 사양입니다. 컴퓨터 구성에 대한 자세한 내용은 시작 → 도움말 및 지원을 클릭하고 컴퓨터에 대한 정보를 확인할 수 있는 옵션을 선택하십시오.
오디오 종류 2.
카메라 카메라 해상도 1.3 메가픽셀 비디오 해상도 640 x 480, 30 fps 에서(최대) 통신 네트워크 어댑터 10/100/1000 Mbps 이더넷 LAN 무선 내부 WLAN(무선 LAN) 포트 및 커넥터 오디오 마이크 커넥터 1 개, 스테레오 헤드폰/스피 커 커넥터 1 개 비디오 • • 네트워크 어댑터 RJ-45 커넥터 1 개 USB 4 핀 USB 2.0 호환 커넥터 3 개 미디어 카드 판독기 3-in-1(SD/MMC/MS) 1 개 15 핀 VGA 커넥터 1 개 19 핀 HDMI 커넥터 1 개 디스플레이 종류 HD WLED TrueLife; HD WLED AG 크기 Vostro 1440/Vostro 1450 14.0” Vostro 1540/Vostro 1550 15.0” 규격: Vostro 1440/Vostro 1450 높이 192.50 mm(7.58 인치) 너비 324.00 mm(12.76 인치) 대각선 355.60 mm(14.
디스플레이 너비 344.20 mm(13.55 인치) 대각선 396.24 mm(15.60 인치) 작동 영역(X/Y) 344.23 mm x 193.54 mm 최대 해상도 1366 x 768 픽셀, 262K 컬러 최대 밝기 220 니트 작동 각도 0° (닫힌 상태) ~ 140° 화면 주사율 60 Hz 최소 가시 각도: 가로 40/40 세로 15/30 (H/L) 픽셀 피치 0.23 mm x 0.23 mm 키보드 키 개수: 미국과 캐나다: 86 개, 유럽과 브라질: 87 개, 일본: 90 개 터치패드 작동 영역: X축 90.00 mm(3.54 인치) Y축 49.00 mm(1.93 인치) 배터리 종류 6 셀 리튬 이온(2.20 Whr) 치수: 높이 20.20 mm(0.80 인치) 너비 208.36 mm(8.20 인치) 깊이 56.52 mm(2.22 인치) 무게 0.33 kg(0.
배터리 전압 11.1 VDC 온도 범위: 작동 시 0 °C ~ 35 °C(32 °F ~ 95 °F) 비작동 시 –40 °C ~ 65 °C(–40 °F ~ 149 °F) 코인 셀 배터리 3 V CR2032 리튬 코인 셀 AC 어댑터 종류: Vostro 1440 / Vostro 1450 / Vostro 1540 / Vostro 1550 (내장형 비디오 카드 포함) 65 W Vostro 1440(개별형 비디오 카드 포함) 65 W Vostro 1450(개별형 비디오 카드 포함) 90 W 입력 전압 100 VAC ~ 240 VAC 입력 전류(최대) 1.50 A/1.60 A/1.70 A/2.10 A 입력 주파수 50 Hz ~ 60 Hz 출력 전원 65 W 및 90 W 출력 전류 65 W 3.34 A(연속) 90 W 4.62 A 정격 출력 전압 19.50 VDC(+/ 1.0 VDC) 치수: 높이 28.20 mm(1.11 인치) 너비 57.90 mm(2.
AC 어댑터 작동 시 0 °C ~ 40 °C(32 °F ~ 104 °F) 비작동 시 –40 °C ~ 70 °C(–40 °F ~ 158 °F) 물리적 사양 Vostro 1440 / Vostro 1450: 높이(WLED 패널 포함) 31.50 mm ~ 34.70 mm(1.24 인치 ~ 1.36 인치) 너비 342.00 mm(13.46 인치) 깊이 244 mm(9.60 인치) 무게(최대) 2.2 kg(4.85 파운드) Vostro 1540 / Vostro 1550: 높이(WLED 패널 포함) 31.50 mm ~ 34.50 mm(1.24 인치 ~ 1.35 인치) 너비 376.00 mm(14.80 인치) 깊이 260 mm(10.23 인치) 무게(최대) 2.37 kg(5.
Dell 에 문의하기 28 노트: 인터넷 연결을 사용할 수 없는 경우에는 제품 구매서, 포장 명세서, 청구 서 또는 Dell 제품 카탈로그에서 연락처 정보를 찾을 수 있습니다. Dell 은 다양한 온라인/전화 기반의 지원 및 서비스 옵션을 제공합니다. 제공 여부는 국가/지역 및 제품에 따라 다르며 일부 서비스는 소재 지역에 제공되지 않을 수 있 습니다. 판매, 기술 지원 또는 고객 서비스 문제에 대해 Dell 에 문의하려면 1. 2. 3. 4. support.dell.com 을 참조하십시오. 지원 카테고리를 선택합니다. 미국 거주 고객이 아닌 경우, 페이지 하단에서 국가 코드를 선택하거나 모두를 선택하여 더 많은 옵션을 표시할 수 있습니다. 필요한 서비스 또는 지원 링크를 선택하십시오.