Dell Vostro 2420 Ägarens handbok Regleringsmodell: P22G Regleringstyp: P22G004
Upplysningar och varningar OBS: Ger viktig information som kan hjälpa dig att få ut mer av datorn. CAUTION: VIKTIGT! Indikerar risk för skada på maskinvaran eller förlust av data, samt ger information om hur du undviker problemet. VARNING: En varning signalerar risk för egendomsskada, personskada eller dödsfall. © 2012 Dell Inc.
Innehåll Upplysningar och varningar.........................................................................................................2 Kapitel 1: Arbeta med datorn........................................................................................................5 Innan du arbetar inuti datorn....................................................................................................................................5 Stänga av datorn.........................................................
Ta bort processorn.................................................................................................................................................26 Installera processorn..............................................................................................................................................27 Ta bort moderkortet................................................................................................................................................
Arbeta med datorn 1 Innan du arbetar inuti datorn Följ säkerhetsanvisningarna nedan för att skydda dig och datorn mot potentiella skador. Om inget annat anges förutsätts i varje procedur i det här dokumentet att följande villkor har uppfyllts: • Du har utfört stegen i Arbeta inuti datorn. • Du har läst säkerhetsinformationen som medföljde datorn. • En komponent kan ersättas eller – om du köper den separat – monteras i omvänd ordning jämfört med borttagningsproceduren.
7. Ta bort huvudbatteriet. 8. Vänd datorn rätt. 9. Öppna skärmen. 10. Tryck på strömbrytaren så att moderkortet jordas. CAUTION: Undvik elektriska stötar genom att alltid koppla loss datorn från eluttaget innan du öppnar skärmen. CAUTION: Jorda dig genom att röra vid en omålad metallyta, till exempel metallen på datorns baksida, innan du vidrör något inuti datorn.
5. Starta datorn.
Ta bort och installera komponenter 2 Det här avsnittet ger detaljerad information om hur man tar bort och installerar komponenter i datorn. Rekommenderade verktyg Procedurerna i detta dokument kan kräva att följande verktyg används: • Liten spårskruvmejsel • Stjärnskruvmejsel • Liten plastrits Ta bort batteriet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Skjut på frigöringshakarna för att låsa upp batteriet. 3. Skjut ut batteriet och ta bort det från datorn.
Installera batteriet 1. Skjut in batteriet i facket tills det klickar på plats. 2. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort SD-kortet (secure digital) 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Tryck in SD-minneskortet för att lossa det från datorn. 3. Skjut ut SD-minneskortet (secure digital) ur datorn. Installera SD-kortet (secure digital) 1. Tryck in minneskortet i facket tills det sitter ordentligt på plats och du hör ett klickljud. 2.
4. Vänd på datorn och ta bort gångjärnskåpan. Installera gångjärnskåpan 1. Installera gångjärnskåpan och tryck på den så att den sitter ordentligt fast i datorn. 2. Vänd på datorn och installera skruvarna som håller fast gångjärnskåpan. 3. Installera batteriet. 4. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort tangentbordet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort batteriet. 3. Börja till höger och bänd upp tangentbordet från datorn.
4. Vänd tangentbordet upp och ned och placera det på handledsstödet. 5. Koppla bort tangentbordskabeln från moderkortet. 6. Ta bort tangentbordet från datorn.
Installera tangentbordet 1. Anslut tangentbordskabeln till moderkortet. 2. Vinkla tangentbordet 30 grader och sätt i det i facket. 3. Tryck tangentbordet nedåt tills den klickar på plats. 4. Installera batteriet. 5. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort den optiska enheten 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort batteriet. 3. Ta bort tangentbordet. 4. Ta bort skruven som håller fast den optiska enheten. 5.
Installera den optiska enheten 1. Skjut in den optiska enheten i facket på vänstersidan av chassit. 2. Dra åt skruven som håller fast den optiska enheten i datorn. 3. Installera tangentbordet. 4. Installera batteriet. 5. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort minnesmodulen 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort batteriet. 3. Ta bort tangentbordet. 4. Bänd bort låsspännena från minnesmodulen tills den hoppar upp. 5.
Installera minnesmodulen 1. Sätt in minnesmodulen i minnessockeln. 2. Tryck nedåt på minnesmodulen tills låsspännena håller minnet på plats. 3. Installera tangentbordet. 4. Installera batteriet. 5. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort handledsstödet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort batteriet. 3. Ta bort tangentbordet. 4. Ta bort skruvarna från datorns bottenplatta. 5.
6. Ta bort skruvarna som håller fast handledsstödet i datorn. 7. Använd en plastrits och bänd försiktigt upp handledsstödet längs kanterna. Lyft upp handledsstödet och ta bort det från datorn. Installera handledsstödet 1. Vinkla handledsstödet till 30 graders vinkel och sätt i det i riktning mot bildskärmen. 2. Börja vid kanten av handledsstödet och tryck det nedåt på handledsstödet så att det krokar fast i flikarna på datorn. 3.
7. Installera batteriet. 8. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort strömbrytarkortet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: a) batteriet b) tangentbordet c) handledsstödet 3. Ta bort kabeln för strömbrytarkortet från tejpen som fäster den vid handledsstödet. 4. Vänd handledsstödet upp och ned och ta bort skruven som håller fast strömbrytarkortet i handledsstödet. 5.
Installera strömbrytarkortet 1. Trä in kabeln för strömbrytarkortet genom öppningen. 2. Sätt fast strömbrytarkortet i dess fack. 3. Installera skruven som håller fast strömbrytarkortet. 4. Vänd på datorn och fäst kabeln för strömbrytarkortet vid handledsstödet. 5. Installera: a) handledsstödet b) tangentbordet c) batteriet 6. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort hårddisken 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2.
Installera hårddisken 1. Installera hårddiskhållaren på hårddisken. 2. Dra åt skruven som håller fast hårddiskhållaren. 3. Placera hårddisken i dess fack och skjut den mot SATA-kontakten så att den sitter ordentligt fast i moderkortet. 4. Installera: a) handledsstödet b) tangentbordet c) batteriet 5. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort kortet för trådlöst lokalt nätverk (WLAN) 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2.
5. Ta bort WLAN-kortet från datorn. Installera kortet för trådlöst lokalt nätverk (WLAN) 1. Skjut in WLAN-kortet i kortplatsen tills det klickar på plats. 2. Anslut antennerna enligt färgkoderna på WLAN-kortet. 3. Installera: a) handledsstödet b) tangentbordet c) batteriet 4. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort knappcellsbatteriet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: a) batteriet b) tangentbordet c) handledsstödet 3.
4. Ta bort knappcellsbatteriet från datorn. Installera knappcellsbatteriet 1. Installera knappcellsbatteriet i dess fack. 2. Anslut kabeln för knappcellsbatteriet till moderkortet. 3. Installera: a) handledsstödet b) tangentbordet c) batteriet 4. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort ljudkortet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: a) batteriet b) tangentbordet c) handledsstödet 3.
4. Lyft upp och ta bort knappcellsbatteriet från dess fack. 5. Koppla bort kabeln för ljudkortet från moderkortet. 6. Bänd i haken för att lossa ljudkortet.
7. Ta bort ljudkortet från datorn. Installera ljudkortet 1. Sätt i ljudkortet i dess fack och snäpp fast haken så att det sitter ordentligt på plats. 2. Anslut kabeln för ljudkortet till moderkortet. 3. Sätt i knappcellsbatteriet i facket och justera det i rätt läge. 4. Anslut antennen till WLAN-kortet. 5. Installera: a) handledsstödet b) tangentbordet c) batteriet 6. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort USB-kortet 1.
4. Ta bort skruven som håller fast USB-kortet. 5. Lyft upp USB-kortet och ta bort det från datorn. Installera USB-kortet 1. Sätt i och justera USB-kortet i dess fack i datorn. 2. Installera skruven som håller USB-kortet på plats. 3. Anslut kabeln för USB-kortet till moderkortet. 4.
d) batteriet 5. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort kylfläns- och fläktmonteringen 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: a) batteriet b) tangentbordet c) handledsstödet 3. Koppla bort processorfläktkabeln från moderkortet. 4. Ta bort fästskruvarna som håller fast kylfläns- och fläktmonteringen genom att följa sekvensen i bilden. 5. Ta bort kylfläns- och fläktmonteringen från datorn.
Installera kylfläns- och fläktmonteringen 1. Sätt i och justera kylfläns- och fläktmonteringen i rätt läge. 2. Dra åt fästskruvarna som håller fast kylfläns- och fläktmonteringen. 3. Anslut processorfläktkabeln till moderkortet. 4. Installera: a) handledsstödet b) tangentbordet c) batteriet 5. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort processorn 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2.
Installera processorn 1. Sätt i processorn i processorsockeln. Kontrollera att den sitter ordentligt på plats. 2. Dra åt kamskruven i medurs riktning till låst läge. 3. Installera: a) b) c) d) 4. kylfläns- och fläktmonteringen handledsstödet tangentbordet batteriet Följ anvisningarna i När du har arbetat inuti datorn. Ta bort moderkortet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: a) b) c) d) e) f) g) h) i) j) 3.
4. Ta bort skruvarna som håller fast moderkortet. 5. Vinkla moderkortet, lyft upp det och skjut ut det från LAN-, VGA-, HDMI- och USB-socklarna. Installera moderkortet 1. Sätt i moderkortet med LAN-, VGA-, HDMI- och USB-kontakterna i respektive socklar och justera in moderkortet i rätt läge. 2. Installera skruvarna som håller moderkortet på plats. 3. Anslut LCD-kabeln, kabeln för strömförsörjningen, kabeln för USB-kortet, kabeln för ljudkortet, kabeln för knappcellsbatteriet och högtalarkabeln. 4.
b) c) d) e) f) g) h) i) j) 5. kylfläns- och fläktmonteringen WLAN-kortet hårddisken handledsstödet minnesmodulen den optiska enheten tangentbordet SD-minneskortet batteriet Följ anvisningarna i När du har arbetat inuti datorn. Ta bort högtalarna 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2.
5. Tryck på låshakarna och lyft upp den högra högtalaren. 6. Ta bort högtalarmonteringen och högtalarkabeln från datorn. Installera högtalarna 1. Sätt i och fäst vänster och höger högtalare i respektive fack. 2. Rikta in och dra högtalarkabeln till chassit. 3.
e) f) g) h) i) j) k) l) m) n) 4. kylfläns- och fläktmonteringen USB-kortet WLAN-kortet hårddisken handledsstödet minnesmodulen den optiska enheten tangentbordet SD-minneskortet batteriet Följ anvisningarna i När du har arbetat inuti datorn. Ta bort bildskärmsmonteringen 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: a) b) c) d) e) batteriet gångjärnskåpan tangentbordet den optiska enheten handledsstödet 3.
6. Ta bort skruvarna som håller fast det vänstra och det högra gångjärnet. 7. Lyft upp bildskärmsmonteringen från datorn och ta bort den. Installera bildskärmsmonteringen 1. Sätt i gångjärnen för bildskärmsmonteringen i dess hållare. 2. Installera skruven som håller fast det högra och det vänstra gångjärnet. 3. Anslut bildskärmskabeln till moderkortet. 4. Rikta in WLAN-antennerna och dra kabeln till hållaren och anslut antennerna till WLAN-kortet. 5. Anslut kabeln för USB-kortet. 6.
b) c) d) e) 7. den optiska enheten tangentbordet gångjärnskåpan batteriet Följ anvisningarna i När du har arbetat inuti datorn. Ta bort bildskärmsramen 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort batteriet. 3. Börja längst ner och bänd ramen från insidan och ut från bildskärmsmonteringen, fortsätt till det högra och vänstra hörnet av bildskärmsramen. 4. Ta bort ramen från bildskärmsmonteringen. Installera bildskärmsramen 1. Rikta in bildskärmsramen i linje med topphöljet.
Ta bort kameran 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort batteriet. 3. Ta bort bildskärmsramen. 4. Koppla bort kamerakabeln från kameramodulen. 5. Bänd loss haken, lyft upp kameran och ta bort den från datorn. Installera kameran 1. Sätt i och justera kameramodulen i dess fack. 2. Anslut kamerakabeln till kameramodulen. 3. Installera bildskärmsramen. 4. Installera batteriet. 5. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort bildskärmspanelen 1.
c) d) e) f) g) tangentbordet den optiska enheten handledsstödet bildskärmsmonteringen bildskärmsramen 3. Koppla bort kamerakabeln från kameramodulen. 4. Ta bort skruvarna som håller fast bildskärmens fäste och gångjärn. 5. Lossa antennerna för trådlös kommunikation från det högra gångjärnet. 6. Lossa bildskärmskabeln från det vänstra gångjärnet.
7. Lyft upp bildskärmspanelen och fästena från bildskärmens topphölje. 8. Ta bort skruvarna från det vänstra och högra fästet och ta bort bildskärmspanelen. Installera bildskärmspanelen 1. Sätt fast det vänstra och högra fästet i bildskärmspanelen och dra åt skruvarna. 2. Sätt i och dra bildskärmskabeln och antennerna för trådlös kommunikation till det vänstra och högra fästet. 3. Rikta in bildskärmspanelen och fästena med topphöljet. 4.
a) b) c) d) e) f) g) 8. bildskärmsramen bildskärmsmonteringen handledsstödet den optiska enheten tangentbordet gångjärnskåpan batteriet Följ anvisningarna i När du har arbetat inuti datorn. Ta bort bildskärmskabeln 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort: a) b) c) d) e) f) g) h) batteriet gångjärnskåpan tangentbordet den optiska enheten handledsstödet bildskärmsmonteringen bildskärmsramen bildskärmspanelen 3. Ta bort tejpen som sitter över bildskärmsanslutningen. 4.
Installera bildskärmskabeln 1. Fäst bildskärmskabeln vid bildskärmspanelen. 2. Anslut bildskärmskabeln till bildskärmspanelen och sätt fast tejpen som håller fast dem. 3. Installera: a) b) c) d) e) f) g) h) 4. 38 bildskärmspanelen bildskärmsramen bildskärmsmonteringen handledsstödet den optiska enheten tangentbordet gångjärnskåpan batteriet Följ anvisningarna i När du har arbetat inuti datorn.
Systeminstallationsprogrammet 3 Med systeminstallationsprogrammet kan du hantera maskinvaran i datorn och ange alternativ för BIOS-nivåer.
Tabell 1. Navigeringstangenter Tangenter Navigering Upp-pil Går till föregående fält. Ned-pil Går till nästa fält. Gör att du kan välja ett värde i det markerade fältet (om sådana finns) eller följer länken i fältet. Mellanslag Visar eller döljer en nedrullningsbar meny, om sådan finns. Går till nästa fokuserade område. OBS: Endast för webbläsare med standardgrafik. Går till föregående sida tills huvudskärmen visas.
Advanced Intel SpeedStep Aktivera eller inaktivera funktionen Intel SpeedStep. Standard: Enabled (aktiverad) Virtualization Aktivera eller inaktivera Intels virtualiseringsfunktion. Standard: Enabled (aktiverad) Integrated NIC Aktivera eller inaktivera strömförsörjning till det inbyggda nätverkskortet. Standard: Enabled (aktiverad) USB Emulation Aktivera eller inaktivera funktionen USB-emulering.
Boot Boot Priority Order Anger ordningen för olika enheter som datorn startar från vid start. Hard Disk Drives Anger vilken hårddisk som datorn kan starta från. USB Storage Device Anger vilken USB-lagringsenhet som datorn kan starta från. CD/DVD ROM Drives Anger vilken cd/dvd som datorn kan starta från. Network Anger vilket nätverk som datorn kan starta från. Exit I det här avsnittet kan du spara, kassera och läsa in standardinställningar innan du avslutar systeminstallationen.
Lösenordstyp Beskrivning Systemlösenord Lösenord som du måste ange för att logga in till systemet. Installationslösenord Lösenord som du måste ange för att öppna och göra ändringar i datorns BIOS-inställningar. CAUTION: Lösenordsfunktionerna ger dig en grundläggande säkerhetsnivå för informationen på datorn. CAUTION: Vem som helst kan komma åt informationen som är lagrad på datorn om den inte är låst och lämnas utan tillsyn.
Starta systeminstallationsprogrammet genom att trycka på omedelbart efter det att datorn startats eller startats om. 1. På skärmen System BIOS (System-BIOS) eller System Setup (Systeminstallation) väljer du System Security (Systemsäkerhet) och trycker på . Skärmen System Security (Systemsäkerhet) visas. 2. På skärmen System Security (Systemsäkerhet), kontrollera att Password Status (Lösenordstatus) är Unlocked (Olåst). 3.
Diagnostik 4 Om du har problem med datorn kör du ePSA-diagnostiken innan du kontaktar Dell för teknisk hjälp. Syftet med att köra diagnostiken är att testa datorns maskinvara utan att ytterligare utrustning krävs och utan att riskera att information går förlorad. Om du inte kan fixa problemet själv kan service- och supportpersonal använda diagnostikresultatet för att hjälpa dig att lösa problemet.
• Konstant blinkande gult ljus – Allvarligt batterifel med ansluten nätadapter. • Lampan släckt - Batteriet är fulladdat och nätadaptern är ansluten. • Vitt ljus – Batteriet laddas med ansluten nätadapter. Lampor för enhetsstatus Tänds när du startar datorn och blinkar när datorn är i strömsparläge. Tänds när datorn läser eller skriver data. Tänds eller blinkar för att visa batteriets tillstånd. Tänds när funktionen för trådlösa nätverk är aktiverad.
5 Tekniska specifikationer OBS: Erbjudanden kan variera mellan olika regioner. Mer information om datorns konfiguration får du om du klickar på Start (Startikon) → Hjälp och support och väljer alternativet att visa datorinformation. Tabell 2. Systeminformation Funktion Specifikationer Kretsuppsättning Intel HM75-expresskretsuppsättning DRAM-bussbredd 64-bitar Flash EPROM SPI 32 Mbit Tabell 3.
Funktion Externt Specifikationer kontakt för mikrofoningång/stereohörlurar/externa högtalare Högtalare 2x2W Volymkontroller funktionstangenter på tangentbordet och programmenyer Tabell 6.
Funktion Specifikationer USB tre USB 2.0-kompatibla kontakter med fyra stift Mediekortläsare en 3-i-1 (SD/MMC/MS) Tabell 10.
Tabell 13. Batteri Funktion Specifikationer Typ 6-cells litiumjonbatteri (2,20 Whr) Mått: Höjd 20,20 mm (0,80 tum) Bredd 208,36 mm (8,20 tum) Djup 56,52 mm (2,22 tum) Vikt 0,33 kg (0,73 pund) Laddningstid ungefär 4 timmar (med datorn avstängd) Spänning 11,1 VDC Temperaturintervall: Vid drift 0 °C till 35 °C (32 °F till 95 °F) Ej i drift –40 °C till 65 °C (–40 °F till 149 °F) Knappcellsbatteri 3 V CR2032-litiumcellbatteri Tabell 14.
Funktion Specifikationer Vid drift 0 °C till 40 °C (32 °F till 104 °F) Ej i drift –40 °C till 70 °C (–40 °F till 158 °F) Tabell 15.
Kontakta Dell 6 OBS: Om du inte har en aktiv Internet-anslutning kan du hitta kontaktinformationen på ditt inköpskvitto, förpackning, faktura eller i Dells produktkatalog. Dell erbjuder flera alternativ för support och service online och på telefon. Tillgängligheten varierar beroende på land och produkt och vissa tjänster kanske inte finns i ditt område. Gör så här för att kontakta Dell för försäljningsärenden, teknisk support eller kundtjänst: 1. Besök support.dell.com. 2. Välj supportkategori. 3.