Dell Vostro 3360 Příručka majitele Regulační model: P32G Regulační typ: P32G001
Poznámky a upozornění POZNÁMKA: POZNÁMKA označuje důležité informace, které pomáhají lepšímu využití počítače. VÝSTRAHA: UPOZORNĚNÍ poukazuje na možnost poškození hardwaru nebo ztráty dat a poskytuje návod, jak se danému problému vyhnout. VAROVÁNÍ: VAROVÁNÍ označuje potenciální nebezpečí poškození majetku, úrazu nebo smrti. © 2012 Dell Inc.
Obsah Poznámky a upozornění.....................................................................................................2 Kapitola 1: Práce na počítači............................................................................................5 Před manipulací uvnitř počítače........................................................................................................................5 Vypnutí počítače..........................................................................................
Vyjmutí modulu kamery.................................................................................................................................28 Vložení modulu kamery..................................................................................................................................28 Vyjmutí ventilátoru........................................................................................................................................28 Vložení ventilátoru............................
Práce na počítači 1 Před manipulací uvnitř počítače Řiďte se těmito bezpečnostními pokyny, které ochrání počítač před případným poškozením a zajistí vaši bezpečnost. Pokud není uvedeno jinak, u každého postupu v tomto dokumentu se předpokládá následující: • Provedli jste kroky uvedené v části Práce na počítači. • Přečetli jste si bezpečnostní informace dodané s počítačem.
POZNÁMKA: Před servisním zásahem uvnitř počítače je třeba vyjmout hlavní baterii, aby nedošlo k poškození základní desky. 7. Vyjměte hlavní baterii. 8. Otočte počítač horní stranou nahoru. 9. Otevřete displej. 10. Stisknutím tlačítka napájení uzemněte základní desku. VÝSTRAHA: Aby nedošlo k úrazu elektrickým proudem, před otevřením krytu počítače vždy odpojte počítač od elektrické zásuvky.
4. Připojte počítač a všechna připojená zařízení do elektrických zásuvek. 5. Zapněte počítač.
Demontáž a montáž součástí 2 V této části naleznete podrobné informace o postupu demontáže a montáže součástí z počítače. Doporučené nástroje Postupy uvedené v tomto dokumentu mohou vyžadovat použití následujících nástrojů: • malý plochý šroubovák, • křížový šroubovák, • malá plastová jehla. Vyjmutí karty SIM 1. Postupujte podle pokynů v části Před manipulací uvnitř počítače. 2. Zasunutím sponky na papír do malého otvoru v držáku karty SIM uvolněte držák z počítače. 3.
4. Vyjměte kartu SIM z držáku karty SIM. Vložení karty SIM 1. Vložte kartu SIM do držáku karty SIM. 2. Zasuňte držák karty SIM s vloženou kartou SIM do slotu. 3. Postupujte podle pokynů v části Po manipulaci uvnitř počítače. Vyjmutí karty SD 1. Postupujte podle pokynů v části Před manipulací uvnitř počítače. 2. Zatlačením na kartu SD uvolněte kartu z počítače. Vysuňte kartu SD z počítače. Vložení karty SD 1. Zasunujte kartu SD do slotu, dokud neuslyšíte cvaknutí. 2.
Instalace přístupového panelu 1. Nasaďte přístupový panel na původní místo v počítači. 2. Utáhněte šroub upevňující přístupový panel k počítači. 3. Postupujte podle pokynů v části Po manipulaci uvnitř počítače. Vyjmutí karty WLAN 1. Postupujte podle pokynů v části Před manipulací uvnitř počítače. 2. Sejměte přístupový panel. 3. Odpojte anténní kabely od karty WLAN a odstraňte šroub upevňující kartu WLAN k počítači. Vyjměte kartu WLAN z počítače. Vložení karty WLAN 1.
Vložení knoflíkové baterie 1. Zatlačte knoflíkovou baterii do slotu na základní desce. 2. Nasaďte přístupový panel. 3. Postupujte podle pokynů v části Po manipulaci uvnitř počítače. Demontáž paměti 1. Postupujte podle pokynů v části Před manipulací uvnitř počítače. 2. Sejměte přístupový panel. 3. Prsty odklopte upevňovací svorky na obou koncích konektoru paměťového modulu (paměťový modul se musí uvolnit a povysunout směrem nahoru).
3. Začněte na pravé straně systému a páčením pomocí tenkého plastového dílu (např. koncem svazovací pásky) oddělte klávesnici od počítače. 4. Obraťte klávesnici a položte ji na opěrku pro dlaně. 5. Zdvižením svorky uvolněte kabel klávesnice a odpojte jej od počítače.
Instalace klávesnice 1. Připojte kabel klávesnice k základní desce. 2. Vložte klávesnici zpět na původní místo. 3. Utažením šroubu upevněte klávesnici k počítači. 4. Postupujte podle pokynů v části Po manipulaci uvnitř počítače. Demontáž opěrky pro dlaně 1. Postupujte podle pokynů v části Před manipulací uvnitř počítače. 2. Demontujte následující součásti: a) přístupový panel, b) klávesnice, c) kryt závěsu displeje. 3. 14 Pomocí tenkého plastového dílu (např.
4. Odstraňte šrouby, které připevňují opěrku pro dlaně k počítači. 5. Odpojte kabel desky pro rychlé spuštění, kabel čtečky otisků prstů a kabel opěrky pro dlaně od základní desky. 6. Odpojte kabel indikátoru napájení a kabel panelu indikátorů od základní desky.
7. Odstraňte šrouby, které připevňují opěrku pro dlaně k přední straně počítače. 8. Páčením podél okrajů uvolněte opěrku pro dlaně.
9. Zvedněte opěrku pro dlaně nahoru a vyjměte ji z počítače. Instalace opěrky pro dlaně 1. Od okrajů opěrky pro dlaně tlačte směrem dolů na opěrku, aby úchyty na počítači zapadly na své místo. 2. Utažením šroubů upevněte opěrku pro dlaně k přední straně počítače. 3. Připojte kabel indikátoru napájení a kabel panelu indikátorů k základní desce. 4. Připojte kabel desky pro rychlé spuštění, kabel čtečky otisků prstů a kabel opěrky pro dlaně k základní desce. 5.
Vyjmutí baterie 1. Postupujte podle pokynů v části Před manipulací uvnitř počítače. 2. Demontujte následující součásti: a) přístupový panel, b) klávesnice, c) opěrka pro dlaně. 3. Odpojte kabel baterie od základní desky. 4. Odstraňte šrouby, které upevňují baterii k základní desce. 5. Vyjměte baterii z počítače.
Vložení baterie 1. Vložte baterii do pozice pro baterii. 2. Vraťte šrouby na místo a utažením upevněte baterii k počítači. 3. Připojte kabel baterie k základní desce. 4. Nainstalujte tyto součásti: a) opěrka pro dlaně, b) klávesnice, c) přístupový panel. 5. Postupujte podle pokynů v části Po manipulaci uvnitř počítače. Demontáž pevného disku 1. Postupujte podle pokynů v části Před manipulací uvnitř počítače. 2. Demontujte následující součásti: a) b) c) d) 3.
4. Zvedněte pevný disk, abyste mohli odpojit kabel pevného disku. 5. Odpojte kabel pevného disku od disku a vyjměte pevný disk z počítače. 6. Odstraňte šrouby upevňující držák pevného disku k disku a držák pevného disku vyjměte.
Instalace pevného disku 1. Utáhněte šrouby upevňující držák pevného disku k disku. 2. Připojte kabel pevného disku k disku a uložte pevný disk na původní místo v počítači. 3. Utažením šroubů upevněte pevný disk k počítači. 4. Nainstalujte tyto součásti: a) b) c) d) 5. baterie, opěrka pro dlaně, klávesnice, přístupový panel. Postupujte podle pokynů v části Po manipulaci uvnitř počítače. Demontáž krytu závěsů displeje 1. Postupujte podle pokynů v části Před manipulací uvnitř počítače. 2.
Instalace krytu závěsů displeje 1. Zarovnejte kryt závěsů displeje s původní pozicí na počítači. 2. Utáhněte šrouby, které upevňují kryt závěsů displeje k počítači. 3. Nasaďte přístupový panel. 4. Postupujte podle pokynů v části Po manipulaci uvnitř počítače. Demontáž sestavy displeje 1. Postupujte podle pokynů v části Před manipulací uvnitř počítače. 2. Demontujte následující součásti: a) b) c) d) e) přístupový panel, klávesnice, opěrka pro dlaně, baterie, kryt závěsů displeje. 3.
Instalace sestavy displeje 1. Připojte kabel displeje k základní desce a utažením šroubů upevněte sestavu displeje k počítači. 2. Provlečte kabel pevného disku přes vodicí úchyty. 3. Provlečte anténní kabely přes vodicí úchyty. 4. Nainstalujte tyto součásti: a) b) c) d) e) 5. kryt závěsu displeje, baterie, opěrka pro dlaně, klávesnice, přístupový panel. Postupujte podle pokynů v části Po manipulaci uvnitř počítače. Demontáž čelního krytu displeje 1.
4. Zvedněte čelní kryt displeje a vyjměte jej ze sestavy displeje. Instalace čelního krytu displeje 1. Zarovnejte čelní kryt displeje se sestavou displeje a jemně jej zatlačte na místo. 2. Nainstalujte tyto součásti: a) kryt závěsů displeje, b) baterie, c) opěrka pro dlaně, d) klávesnice, e) přístupový panel. 3. Postupujte podle pokynů v části Po manipulaci uvnitř počítače. Demontáž displeje 1. Postupujte podle pokynů v části Před manipulací uvnitř počítače. 2.
a) b) c) d) e) f) g) přístupový panel, klávesnice, opěrka pro dlaně, baterie, kryt závěsů displeje, sestava displeje, čelní kryt. 3. Odpojte kabel kamery od konektoru na modulu kamery. 4. Odstraňte šrouby, které upevňují displej k zadnímu krytu displeje. 5. Otočte displej ze sestavy displeje.
6. Položte displej čelní stranou dolů, získáte tak přístup k připojeným kabelům displeje a kamery. 7. Vytažením plastového úchytu odpojte kabel displeje od displeje.
8. Odeberte kabel kamery z displeje. Instalace displeje 1. Uložte kabel kamery na zadní stranu displeje. 2. Připojte kabel displeje ke konektoru na displeji. 3. Uložte displej na původní místo v sestavě displeje. 4. Utažením šroubů připevněte displej k sestavě displeje. 5. Připojte kabel kamery k modulu kamery. 6.
f) klávesnice, g) přístupový panel. 7. Postupujte podle pokynů v části Po manipulaci uvnitř počítače. Vyjmutí modulu kamery 1. Postupujte podle pokynů v části Před manipulací uvnitř počítače. 2. Demontujte následující součásti: a) b) c) d) e) f) g) 3. přístupový panel, klávesnice, opěrka pro dlaně, baterie, kryt závěsů displeje, sestava displeje, čelní kryt. Odpojte kabel kamery od modulu kamery a vyjměte modul kamery ze sestavy displeje. Vložení modulu kamery 1.
3. Odstraňte šroub upevňující ventilátor k počítači. Poté ventilátor zvedněte a odpojte jeho kabel od základní desky. Vložení ventilátoru 1. Připojte kabel ventilátoru k základní desce. 2. Utažením šroubů upevněte ventilátor k počítači. 3. Nainstalujte tyto součásti: a) b) c) d) e) f) 4. sestava displeje, kryt závěsů displeje, baterie, opěrka pro dlaně, klávesnice, přístupový panel. Postupujte podle pokynů v části Po manipulaci uvnitř počítače. Vyjmutí základní desky 1.
4. Odstraňte šrouby, které připevňují základní desku k počítači. 5. Vyjměte kabel pevného disku z cesty pro jeho vedení a obraťte základní desku. Nyní máte přístup ke kabelu konektoru napájení. 6. Odpojte kabel konektoru napájení od základní desky.
Vložení základní desky 1. Připojte kabel konektoru napájení k základní desce. 2. Provlečte kabel pevného disku přes vodicí úchyty. 3. Utáhněte šrouby, které připevňují základní desku k počítači. 4. Připojte kabel desky V/V k desce V/V. 5. Nainstalujte tyto součásti: a) ventilátor, b) sestava displeje, c) kryt závěsů displeje, d) baterie, e) opěrka pro dlaně, f) klávesnice, g) přístupový panel. 6. Postupujte podle pokynů v části Po manipulaci uvnitř počítače. Demontáž chladiče 1.
4. Sejměte chladič ze základní desky. Instalace chladiče 1. Utáhněte šrouby upevňující chladič k základní desce. 2. Nainstalujte tyto součásti: a) b) c) d) e) f) g) h) 3. základní deska, ventilátor, sestava displeje, kryt závěsů displeje, baterie, opěrka pro dlaně, klávesnice, přístupový panel. Postupujte podle pokynů v části Po manipulaci uvnitř počítače. Vyjmutí reproduktorů 1. 2. Postupujte podle pokynů v části Před manipulací uvnitř počítače. Demontujte následující součásti: a) b) c) d) e) 3.
4. Uvolněte kabely reproduktorů z cesty pro jejich vedení a vyjměte reproduktory z počítače. Vložení reproduktorů 1. Umístěte reproduktory na počítač a provlečte kabel reproduktorů přes vodicí úchyty. 2. Připojte kabel reproduktorů k desce V/V. 3. Nainstalujte tyto součásti: a) b) c) d) e) 4. pevný disk, baterie, opěrka pro dlaně, klávesnice, přístupový panel. Postupujte podle pokynů v části Po manipulaci uvnitř počítače.
Demontáž konektoru napájení 1. Postupujte podle pokynů v části Před manipulací uvnitř počítače. 2. Demontujte následující součásti: a) b) c) d) e) f) g) h) 3. přístupový panel, klávesnice, opěrka pro dlaně, baterie, kryt závěsů displeje, sestava displeje, ventilátor, základní deska. Odstraňte šroub upevňující konektor napájení k počítači. Poté konektor napájení vyjměte z počítače. Instalace konektoru napájení 1. Utáhněte šroub upevňující konektor napájení k počítači. 2.
4. Odstraňte šrouby, které upevňují desku V/V k počítači, a vyjměte ji z počítače. Vložení desky V/V 1. Připojte kabel reproduktorů a kabel desky V/V k desce V/V. 2. Utáhněte šrouby, které připevňují desku V/V k počítači. 3. Nainstalujte tyto součásti: a) b) c) d) 4. baterie, opěrka pro dlaně, klávesnice, přístupový panel. Postupujte podle pokynů v části Po manipulaci uvnitř počítače.
Nastavení systému 3 Nástroj Nastavení systému umožňuje spravovat hardware počítače a měnit možnosti v systému BIOS.
Tabulka 1. Navigační klávesy Klávesy Navigace Šipka nahoru Přechod na předchozí pole. Šipka dolů Přechod na další pole. Výběr hodnoty ve vybraném poli (je-li to možné) nebo přechod na odkaz v poli. Mezerník Rozbalení a sbalení rozevírací nabídky (je-li to možné). Přechod na další specifickou oblast. POZNÁMKA: Pouze u standardního grafického prohlížeče. Přechod na předchozí stránku až do dosažení hlavní obrazovky.
Main (Hlavní) L2 Cache (Cache L2) Zobrazí velikost cache L2 procesoru. L3 Cache (Cache L3) Zobrazí velikost cache L3 procesoru. Fixed HDD (Fixní pevný disk) Zobrazí modelové číslo a kapacitu pevného disku. SATA ODD (Optická jednotka SATA) Zobrazí číslo modelu a kapacitu optické jednotky. mSata Device (Zařízení mSata) Zobrazí číslo modelu a kapacitu zařízení mini-Sata. AC Adapter Type (Typ adaptéru napájení stř. proudem) Zobrazí typ napájecího adaptéru.
Advanced (Pokročilé) Adapter Warnings (Varování adaptéru) Povolí nebo zakáže varování adaptéru. Výchozí hodnota: Enabled (Povoleno) Function Key Behavior (Chování funkční klávesy) Určuje chování funkční klávesy . Výchozí nastavení: Function key first (Nejprve funkční klávesa) Charger Behavior (Chování nabíječky) Určuje, zda má být po připojení ke zdroji napájení nabíjena baterie počítače. Výchozí hodnota: Enabled (Povoleno) Battery Health (Stav baterie) Informuje o stavu baterie.
Tabulka 4. Možnosti na kartě Security (Zabezpečení) Security (Zabezpečení) Set Service Tag (Nastavit výrobní číslo) V tomto poli se zobrazuje výrobní číslo systému. Jestliže nebylo dosud zadáno, můžete jej zadat do tohoto pole. Admin Password (Heslo správce) Toto pole informuje o tom, zda je pro počítač nastaveno heslo správce (výchozí hodnota: prázdné pole / není nastaveno).
POZNÁMKA: V případě stolních počítačů je servisní označení uvedeno na přední straně počítače. POZNÁMKA: V případě notebooků je servisní označení uvedeno na spodní straně počítače. a) Zadejte servisní označení nebo kód expresní služby a klepněte na tlačítko Submit (Odeslat). b) Klepněte na tlačítko Submit (Odeslat) a pokračujte krokem 5. 4.
Otevře se obrazovka System Security (Zabezpečení systému). 2. Na obrazovce System Security (Zabezpečení systému) ověřte, zda je v nastavení Password Status (Stav hesla) vybrána možnost Unlocked (Odemčeno). 3. Vyberte možnost System Password (Heslo systému), zadejte heslo systému a stiskněte klávesu nebo . Nové heslo systému přiřaďte podle následujících pokynů: – Heslo smí obsahovat nejvýše 32 znaků. – Heslo smí obsahovat čísla od 0 do 9.
Diagnostika 4 Vyskytnou-li se potíže s počítačem, spusťte před kontaktováním společnosti Dell a vyhledáním technické podpory diagnostiku ePSA. Cílem diagnostiky je vyzkoušet hardware počítače bez nutnosti použít dodatečné zařízení nebo rizika ztráty dat. Pokud nedokážete problém sami napravit, výsledky diagnostiky mohou zaměstnancům podpory pomoci ve vyřešení problému za vás.
Indikátory stavu zařízení Tabulka 6. Indikátory stavu zařízení Svítí po zapnutí počítače. Bliká, když je počítač v režimu řízení spotřeby. Svítí, když počítač čte nebo zapisuje data. Svítí nebo bliká podle stavu nabití baterie. Svítí, když je aktivována bezdrátová síť.
Zvukový signál 3 4 Popis • Chyba čipové sady (čipová sada North Bridge a South Bridge, DMA/IMR/časovač). • Došlo k selhání testu hodin. • Došlo k selhání brány A20. • Došlo k selhání čipu Super V/V. • Došlo k selhání testu řadiče klávesnice. Došlo k selhání čtení či zápisu paměti RAM. Možná příčina / Kroky při odstraňování problému Došlo k selhání základní desky. Pokud není zjištěna žádná paměť, proveďte tyto kroky: • Znovu usaďte paměť ve slotu, je-li k dispozici další paměť.
5 Technické údaje POZNÁMKA: Nabízené možnosti se mohou lišit podle oblasti. Chcete-li získat více informací o konfiguraci počítače, klikněte na tlačítko Start o počítači. (ikona Start) → Nápověda a podpora a výběrem příslušné možnosti zobrazíte informace Tabulka 8. Systémové informace Funkce Popis Čipová sada Čipová sada lntel HM77 Express Šířka sběrnice DRAM 64 bitů Paměť Flash EPROM: Vostro 3360 / Vostro 3460 8 MB pro rozhraní SPI Vostro 3560 6 MB pro rozhraní SPI Tabulka 9.
Funkce Popis Vostro 3360 Cirrus Logic CS4213D Vostro 3460 / Vostro 3560 Conexant CX20672-21Z Převod stereofonního signálu 24bitový (analogový signál na digitální a digitální na analogový) Rozhraní: Interní zvuk High Definition Externí vstup pro mikrofon / výstup pro stereofonní sluchátka a externí reproduktory Reproduktory 2 W Ovládání hlasitosti funkční klávesy na klávesnici a nabídky programů Tabulka 12.
Tabulka 14. Komunikace Funkce Popis Síťový adaptér Ethernetová síť LAN 10/100/1000 Mb/s Bezdrátové připojení • interní adaptér WLAN • Bluetooth • WWAN (volitelné) Tabulka 15. Porty a konektory Funkce Popis Zvuk: Vostro 3360 jeden stereofonní výstup zvuku pro sluchátka a náhlavní sadu Vostro 3460 / 3560 jeden konektor pro mikrofon a jeden pro sluchátka Grafika Síťový adaptér • jeden 15kolíkový konektor VGA • jeden 19kolíkový konektor HDMI jeden konektor RJ-45 USB 3.
Funkce Popis Vostro 3360 / 3460 1 366 x 768 pixelů, 262 000 barev Vostro 3560 1 920 x 1 080 Full HD Maximální jas 200 nitů Provozní úhel 0° (zavřený) až 140° Obnovovací frekvence 60 Hz Minimální pozorovací úhly: Horizontální 40° / 40° Vertikální 15° / 30° (V / Š) Rozteč pixelů 0,23 x 0,23 mm Tabulka 17.
Funkce Popis Napětí: Vostro 3360 14,8 V stejn. proudu Vostro 3460 / Vostro 3560 11,1 V stejn. proudu Teplotní rozsah: Provozní 0–35 °C (32–95 °F) Neprovozní -40–65 °C (-40–149 °F) Knoflíková baterie 3V lithiová CR2032 Tabulka 20. Napájecí adaptér Funkce Popis Typ: Vostro 3360 / Vostro 3460 / Vostro 3560 s integrovaným grafickým čipem 65 W Vostro 3460 se samostatnou grafickou kartou 90 W Vostro 3560 s 4jádrovým procesorem 90 W Vstupní napětí 100–240 V stř. napětí Vstupní proud (max.
Tabulka 21. Rozměry a hmotnost Funkce Popis Vostro 3360 Vostro 3460 Výška 19,20 mm (0,75 palce) 30,10 mm (1,18 palce) 32,50 mm (1,27 palce) Šířka 332,00 mm (13,07 palců) 345,50 mm (13,60 palců) 375,00 mm (14,76 palců) Hloubka 232,50 mm (9,15 palců) 244,00 mm (9,60 palců) 259,00 mm (10,19 palců) Hmotnost (s baterií) 1,66 kg (3,65 liber) 2,23 kg (4,91 Iiber) 2,57 kg (5,66 Iiber) Tabulka 22.
Jak kontaktovat společnost Dell 6 POZNÁMKA: Pokud nemáte aktivní internetové připojení, můžete najít kontaktní informace na nákupní faktuře, balicím seznamu, účtence nebo v katalogu produktů společnosti Dell. Společnost Dell nabízí několik možností online a telefonické podpory a služeb. Jejich dostupnost závisí na zemi a produktu a některé služby nemusí být ve vaší oblasti k dispozici.