Vostro 3400 Servicemanual Forordningsmodel: P132G Forordningstype: P132G003 / P132G004 April 2021 rev.
Bemærk, forsigtig og advarsel BEMÆRK: En NOTE angiver vigtige oplysninger, som hjælper dig med at bruge produktet bedre. FORSIGTIG: FORSIGTIG angiver enten en mulig beskadigelse af hardware eller tab af data, og oplyser dig om, hvordan du kan undgå dette problem. ADVARSEL: ADVARSEL angiver risiko for tingskade, legemsbeskadigelse eller død. © 2020-2021 Dell Inc. Eller dets associerede selskaber. Alle rettigheder forbeholdes. Dell, EMC, og andre varemærker er varemærker tilhørende Dell Inc.
Indholdsfortegnelse Kapitel 1: Sådan arbejder du med computeren................................................................................... 6 Sikkerhedsinstruktioner.........................................................................................................................................................6 Før du udfører arbejde på computerens indvendige dele........................................................................................... 6 Sikkerhedsforanstaltninger............
Møntcellebatteri.................................................................................................................................................................. 39 Sådan fjernes møntcellen............................................................................................................................................. 39 Sådan installeres møntcellebatteriet...........................................................................................................................
Forbedret Pre-Boot System Assessment – ePSA-diagnosticering.............................................................................. 83 Kørsel af SupportAssist-diagnosticering.....................................................................................................................83 Systemdiagnosticeringsindikatorer....................................................................................................................................84 Wi-Fi-strømcyklus...........................
1 Sådan arbejder du med computeren Emner: • Sikkerhedsinstruktioner Sikkerhedsinstruktioner Forudsætninger Følg sikkerhedsinstruktionerne med henblik på din egen sikkerhed og for at beskytte computeren og arbejdsmiljøet mod mulige skader. Hvis intet andet er angivet bygger hver fremgangsmåde i dette dokument på følgende forudsætninger: ● Du har læst sikkerhedsoplysningerne, som fulgte med computeren.
4. Frakobl alle tilsluttede netværksenheder og perifert udstyr så som tastatur, mus og skærm fra computeren. 5. Fjern alle mediekort og optiske diske fra computeren, hvis relevant. 6. Tryk på strømknappen i 5 sekunder, efter stikket er taget ud af stikkontakten, for at jorde systemkortet. FORSIGTIG: Anbring computeren på en blød og ren overflade for at undgå ridser på skærmen. 7. Placer computeren med oversiden nedad.
● Håndter alle statisk følsomme komponenter i et statisk sikkert område. Brug antistatisk gulv- og bordbelægning, hvor det er muligt. ● Når du pakker en statisk følsom komponent ud af emballagen, skal du ikke fjerne komponenten fra det antistatiske emballagemateriale, før du er klar til at installere komponenten. Sørg for at aflade statisk elektricitet fra din krop, inden du åbner det antistatiske emballagemateriale.
Efter du har udført arbejde på computerens indvendige dele Om denne opgave BEMÆRK: Det kan beskadige computeren alvorligt at efterlade bortkomme eller løse skruer inde i computeren. Trin 1. Genmonter alle skruer, og sørg for, at der ikke er løse skruer inde i din computer. 2. Tilslut alle eksterne enheder, alt tilbehør eller alle kabler, som du fjernede, før du begyndte at udføre arbejde på computeren. 3.
2 Teknologi og komponenter Dette kapitel giver detaljerede oplysninger om teknologi og komponenter, der er tilgængelige i systemet. Emner: • • • USB-funktioner LED-adfærd for tænd/sluk-knap HDMI 1.4 USB-funktioner Universal Serial Bus eller USB blev introduceret i 1996. Det forenklede markant forbindelsen mellem værtscomputere og eksterne enheder såsom mus, tastaturer, eksterne drivere og printere. Tabel 1. USB-udvikling Type Dataoverførselshastighed Kategori Introduktionsår USB 2.
● USB 3.2, 1. gen. bruger en tovejs-grænseflade i modsætning til halv-dupleks som USB 2.0. Dette giver en 10-dobling af den teoretiske båndbredde. Med de konstant stigende krav til dataoverførsel i form af HD-videoindhold, lagerenheder på flere TB, digitalkameraer med høj opløsning osv. er USB 2.0 muligvis ikke hurtig nok. Ydermere vil USB 2.
LED-adfærd for tænd/sluk-knap uden fingeraftrykslæser ● Systemet er tændt (S0) = LED lyser konstant hvidt op. ● Systemet slumrer/på standby (S3, SOix) = LED er slukket ● Systemet is slukket/i dvale (S4/S5) = LED er slukket Opstarts og LED-adfærd med fingeraftrykslæser ● ● ● ● ● ● ● ● ● Ved at holde tænd/sluk-knappen nede i et tidsrum på mellem 50 msek. til 2 sek. tænder man enheden. Tænd/sluk-knappen registrerer ikke yderligere tryk, før SOL (Sign-Of-Life) er blevet givet til brugeren.
1. Konstant hvid – batteriet oplader. Når opladningen er afsluttet slukker LED'en. ○ Hvis computeren kører på et batteri, fungerer lampen på følgende måde: 1. Fra – batteriet er tilstrækkeligt opladet (eller computeren er slukket). 2. Konstant ravgul – batteristanden er kritisk lav. En lav batteritilstand er omkring 30 minutter eller mindre resterende batteritid. ● Kamera-LED ○ Hvid LED tænder, når kameraet er tændt.
3 14 Sprængbillede
Sprængbillede Sprængbillede 15
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Bunddæksel Batteri DC-indgangsport Hukommelsesmoduler Solid state-drevets beslag Solid state-drev Systemkort Højttalere Touchpad Skærmmodul Håndledsstøttemodul Harddiskmodul I/O-kort Knapcellebatteri Tænd/sluk-knapmodul WLAN-kort Blæsermodul Kølelegememodul BEMÆRK: Dell leverer en komponentliste med de tilsvarende komponentnumre for den købte originale systemkonfiguration.
4 Større komponenter Større komponenter 17
5 Adskillelse og samling BEMÆRK: Billederne i dette dokument kan afvige fra din computer afhængigt af den bestilte konfiguration.
Om denne opgave Trin 1. Tryk på Secure Digital-kortet for at frigøre det fra computeren. 2. Skub Secure Digital-kortet ud af computeren. Sådan installeres Secure Digital-kortet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Om denne opgave Trin Skub Secure Digital-kortet ind i slottet, indtil det klikker på plads. Næste trin 1. Følg proceduren under Efter du har arbejde på computerens indvendige dele Bunddæksel Sådan fjernes bunddækslet Forudsætninger 1. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. 2. Fjern SD-kortet.
Om denne opgave Adskillelse og samling 21
Trin 1. Fjern de syv skruer (M2,5x5), og løsn de to fastmonterede skruer fra bunddækslet. 2. Lirk bunddækslet op ved at begynde fra indhakkene i de U-formede riller på bunddækslets øverste kant ved hængslerne. BEMÆRK: FORSIGTIG: Lirk IKKE bunddækslet op ved kanten tæt på udluftningsåbningerne øverst på bunddækslet, da dette kan beskadige bunddækslet. 3. Løft den øverste side af bunddækslet op, og fjern det fra systemet.
Om denne opgave Adskillelse og samling 23
Trin 1. Placer bunddækslet på computeren, og tryk bunddækslets kanter og sider ned, indtil det klikker på plads. 2. Spænd de syv skruer (M2,5x5) og de to fastmonterede skruer, der fastgør bunddækslet til computeren. Næste trin 1. Genmonter SD-kortet 2. Følg proceduren under Efter du har arbejde på computerens indvendige dele Batteri Forholdsregler for litium-ion-batteri FORSIGTIG: ● Vær forsigtig, når du håndterer lithium-ion-batterier.
Om denne opgave Trin 1. Tag tapen af, der dækker batteristikket. 2. Kobl batteriets kabel fra stikket på systemkortet. Sådan genforbindes batteriet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Om denne opgave Trin 1. Slut batteriets kabel til stikket på systemkortet. 2. Sæt tapen, der dækker batteristikket, på igen. Næste trin 1. Monter bunddækslet. 2. Monter SD-kortet. 3. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Sådan fjernes batteriet Forudsætninger 1. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. 2. Fjern SD-kortet. 3. Fjern bunddækslet.
Trin 1. Fjern de tre skruer (M2x3), der fastgør batteriet til håndledsstøtten. 2. Løft batteriet væk fra computeren. Sådan installeres batteriet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Om denne opgave Trin 1. Ret batteriets tapper ind med slottene på håndledsstøttemodulet. BEMÆRK: Når du monterer batteriet i systemet, skal du skubbe tappen på nederste venstre hjørne af batteriet ind under haspen under håndledsstøtten. 2. Genmonter de tre skruer (M2x3), der fastgør batteriet på håndledsstøtten. 3. Slut batterikablet til stikket på systemkortet igen.
Hukommelsesmoduler Sådan fjernes hukommelsesmodulet Forudsætninger 1. 2. 3. 4. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-kortet. Fjern bunddækslet. Frakobl batterikablet. Om denne opgave Trin 1. Tryk på klemmerne, der fastgør hukommelsesmodulet, indtil hukommelsesmodulet hopper op. 2. Fjern hukommelsesmodulet fra hukommelsesmodulets slot.
Om denne opgave Trin 1. Flugt indhakket i hukommelsesmodulet med tappen på hukommelsesmodulets slot, og skub hukommelsesmodulet vinkelret ind i slotten. 2. Tryk hukommelsesmodulet ned, indtil klemmerne holder det fast. BEMÆRK: Hvis du ikke hører et klik, skal du fjerne hukommelsesmodulet og sætte det i igen. Næste trin 1. 2. 3. 4. Tilslut batterikablet. Monter bunddækslet. Monter SD-kortet.
Om denne opgave Trin 1. Fjern den enkelte skrue (M2x3), der fastgør WLAN-kortbeslaget til systemkortet. 2. Skub og fjern WLAN-kortets beslag, som fastgør WLAN-antennekablerne. 3. Kobl WLAN-antennekablerne fra stikkene på WLAN-kortet. 4. Træk WLAN-kortet ud af M.2-porten på systemkortet. Sådan monteres WLAN-kortet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Om denne opgave Trin 1. Genmonter WLAN-kortet i M.2-slotten på systemkortet. 2. Slut WLAN-antennekablerne til stikkene på WLAN-kortet. BEMÆRK: Tabel 3. WLAN-antennekabler Kabelfarve Indikator på WLAN Blå Hvid trekant Orange Sort trekant 3. Placer WLAN-kortets beslag for at fastgøre WLAN-antennekablerne til WLAN-kortet. 4. Genmonter skruen (M2x3), der fastgør WLAN-beslaget og WLAN-kortet til håndledsstøtten. Næste trin 1. 2. 3. 4. 32 Tilslut batterikablet. Monter bunddækslet. Monter SD-kortet.
Solid state-drev Sådan fjernes M.2 2230 solid state-drevet Forudsætninger 1. 2. 3. 4. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-kortet. Fjern bunddækslet. Frakobl batterikablet. Om denne opgave Trin 1. Fjern den enkelte skrue (M2x2,2), og løsn den enkelte fastmonterede skrue, der fastgør SSD-drevets termiske plade på håndledsstøtten, og tag det ud af systemet. 2. Vend varmeafskærmningen om, og fjern skruen (M2x2), der fastgør M.
Om denne opgave Trin 1. Anbring solid state-drevet i varmeafskærmningen, og monter den enkelte skrue (M2x2). 2. Skub og indsæt tappen på solid state-drevet i solid state-drevets slot. 3. Genmonter den ene skrue (M2x2,2), og stram den fastmonterede skrue, der fastgør varmeafskærmningen til håndledsstøtten. Næste trin 1. 2. 3. 4. Tilslut batterikablet. Monter bunddækslet. Monter SD-kortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Sådan fjernes M.
Om denne opgave Trin 1. Fjern de to skruer (M2x2,2) fra det termiske beslag, og fjern beslaget fra systemet. 2. Tag solid state-drevet ud af M.2-slotten på systemkortet, og fjern det fra systemet. Sådan monteres M.2 2280 solid state-drevet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Om denne opgave Trin 1. Isæt solid state-drevet ved at skubbe det ind i M.2-porten på systemkortet. 2. Placer det termiske beslag på solid state-drevet, genmonter de to skruer (M2x2,2), der fastgør den termiske plade på håndledsstøtten. Næste trin 1. 2. 3. 4. Tilslut batterikablet. Monter bunddækslet. Monter SD-kortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Harddisk Sådan fjernes harddiskmodulet Forudsætninger 1. 2. 3. 4.
Om denne opgave Trin 1. Løft låsen, og kobl harddiskkablet fra systemkortet. 2. Fjern de fire skruer (M2x3), der fastgør harddiskmodulet til håndledsstøtten, og løft harddiskmodulet og dets kabler ud af systemet. 3. Frigør mellemkortet fra harddisken. 4. Fjern de fire skruer (M3x3) fra harddiskbeslaget for at frigøre harddisken. Sådan monteres harddiskmodulet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Om denne opgave Trin 1. Juster harddisken ind efter harddiskbeslaget, og genmonter de fire skruer (M3x3). 2. Tilslut mellemlægget til harddisken. 3. Placer harddiskmodulet korrekt på håndledsstøtten, og genmonter de fire skruer (M2x3), der fastgør harddiskmodulet til håndledsstøtten. 4. Slut harddiskens kabel til systemkortet, og luk låsen for at fastgøre kablet. Næste trin 1. 2. 3. 4. 38 Monter batteriet. Monter bunddækslet. Monter SD-kortet.
Møntcellebatteri Sådan fjernes møntcellen Forudsætninger 1. 2. 3. 4. 5. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-kortet. Fjern bunddækslet. Frakobl batterikablet. Fjern I/O-kortet. BEMÆRK: Møntcellebatteriet er monteret på IO-kortet. Om denne opgave Trin 1. Lirk forsigtigt, vha. en plastikpen, møntcellebatteriet ud af slotten på I/O-datterkortet. 2. Fjern møntcellebatteriet fra I/O-datterkortet.
Sådan installeres møntcellebatteriet Om denne opgave Trin 1. Indsæt møntcellebatteriet i soklen på I/O-kortet med +-siden opad. 2. Tryk batteriet ned, indtil det klikker på plads. Næste trin 1. 2. 3. 4. 5. Monter IO-kortet. Tilslut batterikablet. Monter bunddækslet. Monter SD-kortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Systemblæser Sådan fjernes systemblæseren Forudsætninger 1. 2. 3. 4. 40 Følg proceduren i Før du udfører arbejde på computerens indvendige dele.
Om denne opgave Trin 1. Fjern blæserkablet fra stikket på systemkortet, og tag kablet ud af kabelkanalerne på blæsermodulet. 2. Fjern de to skruer (M2,5x5), der fastgør blæseren på håndledsstøtten. Sådan monteres systemblæseren Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Om denne opgave Trin 1. Placer blæseren korrekt på håndledsstøtten. 2. Genmonter de to skruer (M2,5x5), der fastgør blæseren på håndledsstøtten. 3. Før skærmkablet gennem kabelkanalerne på blæsermodulet, og slut blæserkablet til stikket på systemkortet. Næste trin 1. 2. 3. 4. Tilslut batterikablet igen. Genmonter bunddækslet. Genmonter SD-kortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Varme-sink Sådan fjernes kølelegemet - UMA Forudsætninger 1. 2. 3. 4.
Om denne opgave Trin 1. Løsn de fire fastmonterede skruer, der fastgør kølelegemet til systemkortet. 2. Løft kølelegemet op fra systemkortet. Sådan installeres kølelegemet - UMA Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Om denne opgave Trin 1. Placer kølelegemet på systemkortet, og få de fastmonterede skruer på kølelegemet til at flugte med skruehullerne på systemkortet. 2. Spænd de fire fastmonterede skruer, der fastgør kølelegemet til systemkortet. Næste trin 1. 2. 3. 4. Tilslut batterikablet igen. Monter bunddækslet. Monter SD-kortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Sådan fjernes kølelegemet- dedikeret Forudsætninger 1. 2. 3. 4.
Om denne opgave Trin 1. Løsn de fire fastmonterede skruer, og fjern de tre (M2x3) skruer, der holder kølelegemet fast til systemkortet. 2. Løft kølelegemet op fra systemkortet. Sådan installeres kølelegemet- dedikeret Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Om denne opgave Trin 1. Placer kølelegemet på systemkortet, og få de fastmonterede skruer på kølelegemet til at flugte med skruehullerne på systemkortet. 2. Spænd de fire fastmonterede skruer, og monter de tre (M2x4) skruer, der fastgør kølelegemet til systemkortet. Næste trin 1. 2. 3. 4. Tilslut batterikablet igen. Monter bunddækslet. Monter SD-kortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Højttalere Sådan fjernes højtalerne Forudsætninger 1. 2. 3. 4. 5.
Om denne opgave Trin 1. Kobl højtalerkablet fra systemkortet. 2. Tag højttalerkablet ud af kabelkanalerne på håndledsstøtten. 3. Løft højttalerne sammen med kablet ud af systemet. Sådan monteres højttalerne Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages. Om denne opgave BEMÆRK: Hvis gummidutterne skubbes ud, når højttalerne fjernes, skal de skubbes tilbage, før højttalerne genmonteres.
Trin 1. Anbring vha. styremærkerne og gummidutterne højttalerne i slottene på håndledsstøtten. 2. Før højttalerkablet gennem kabelkanalerne på håndledsstøtten. 3. Slut højttalerkablet til stikket på systemkortet. Næste trin 1. 2. 3. 4. 5. Monter SSD'et. Tilslut batterikablet igen. Monter bunddækslet. Monter SD-kortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele IO-kort Sådan fjernes I/O-kortet Forudsætninger 1. 2. 3. 4.
Om denne opgave Trin 1. [På modeller med fingeraftrykslæser]: Kobl fingeraftrykslæseren fra I/O-datterkortets FFC-kabel og I/O-datterkortet fra systemkortets FFC-kabel fra I/O-datterkortet. 2. [På modeller uden fingeraftrykslæser]: Kobl tænd/sluk-knappens FFC-kabel, I/O-datterkortets FFC-kabel og skærmkablet fra systemkortet. 3. Pil tænd/sluk-knappens FFC-kabel samt I/O-datterkortets FFC-kabel af håndledsstøtten. 4.
Om denne opgave Trin 1. Slut tænd/sluk-knappens FFC-kabel og I/O-datterkortets FFC-kabel til I/O-datterkortet igen. 2. Placer I/O-datterkortet på systemet. 3. Genmonter de fire skruer (M2x4), der fastgør IO-datterkortet på håndledsstøtten. 4. [På modeller uden fingeraftrykslæser]: Slut tænd/sluk-knappens FFC-kabel, I/O-datterkortets FFC-kabel og skærmkablet til stikkene på systemkortet igen. 5.
2. Fjern SD-kortet. 3. Fjern bunddækslet. 4. Fjern batteriet. Om denne opgave Trin 1. Kobl touchpad’ens FFC-kabel fra systemkortet. 2. Fjern ledetapen fra touchpadmodulet. 3. Fjern de tre skruer (M2x2), der holder touchpadbeslaget på plads. 4. Fjern touchpadbeslaget fra systemet. 5. Fjern de to skruer (M2x2), der holder touchpadmodulet på plads. 6. Fjern touchpadmodulet med dets FFC-kabel fra systemet. 7. Kobl pegefeltets FFC-kabel fra touchpadmodulet.
Trin 1. Slut pegefeltets FFC-kabel til touchpadmodulet igen. 2. Juster og anbring touchpadmodulet på systemet. BEMÆRK: Når du monterer touchpadbeslaget på Vostro 3400, skal du indsætte dets øverste hjørner under de to tapper på håndledsstøtten. 3. Genmonter de to skruer (M2x2), der fastgør touchpadmodulet på håndledsstøtten. 4. Monter pegefeltbeslaget på touchpadmodulet, og fastgør det vha. de tre skruer (M2x2). 5. Fjern ledetapen over touchpadmodulet. 6. Slut touchpad’ens FFC-kabel til systemkortet.
Skærmmodul Sådan fjernes skærmmodulet Forudsætninger 1. 2. 3. 4. 5. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-kortet. Fjern bunddækslet. Frakobl batterikablet. Fjern WLAN.
Trin 1. Frakobling af skærmkablet fra stikket på systemkortet.
2. Fjern skærmkablet og WLAN-antennekablerne fra kabelkanalerne. 3. Åben systemet til mindst 90 grader, og placer systemet på kanten af bordet, så håndledsstøtten ligger plant på bordet, og skærmmodulet er over kanten. 4. Fjern de fire skruer (M2,5x5), der holder skærmmodulet på plads. 5. Tag skærmmodulet ud af systemet. Sådan installeres skærmmodulet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Trin 1. Ret systemet ind, og placer det under hængslerne på skærmmodulet. 2. Monter de tre skruer (M2,5x5), der holder skærmmodulet på plads.
3. Før igen skærmkablet og WLAN-antennekablerne gennem kabelkanalerne på håndledsstøtten. 4. Slut skærmkablet til stikket på systemkortet igen. Næste trin 1. 2. 3. 4. Monter WLAN Monter bunddækslet. Monter SD-kortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Skærmfacet Sådan fjernes skærmfacetten Forudsætninger 1. 2. 3. 4. 5. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-kortet. Fjern bunddækslet. Fjern batterikablet.
2. Lirk skærmrammen åben fra inderkanten på den øverste del af skærmmodulet. 3. Lirk hængselshætterne på undersiden af skærmmodulet op.
4. Lirk skærmrammen åben fra inderkanten på den nederste del af skærmmodulet. 5. Løft og fjern skærmrammen fra skærmmodulet.
BEMÆRK: ADVARSEL: DU MÅ IKKE bruge en pen eller en anden genstand til at lirke skærmpanelet af som vist i nedenstående billeder, da pennens tryk på skærmpanelet vil beskadige det. Montering af skærmkanten Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Om denne opgave Trin Juster skærmfacetten med skærmens bagdæksel og antennemodul og sæt forsigtigt skærmfacetten tilbage på plads. Næste trin 1. 2. 3. 4. 5. Monter skærmmodulet. Tilslut batterikablet igen. Monter bunddækslet. Monter SD-kortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Skærmpanel Sådan fjernes skærmpanelet Forudsætninger 1. 2. 3. 4. 5. 6. 7. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-kortet. Fjern bunddækslet.
Om denne opgave 62 Adskillelse og samling
Trin 1. Fjern de seks skruer (M2,5x2,5), der fastgør skærmpanelet til hængslerne. 2. Skub forsigtigt skærmpanelmodulet fremad, og fjern Mylar®-tapen, som fastgør skærmkablet bag på skærmpanelet. BEMÆRK: Sørg for at lægge panelet på en ren og glat overflade for at undgå beskadigelse. 3. Kobl skærmkablet fra skærmpanelmodulet, og løft skærmpanelet ud af systemet. BEMÆRK: Fjern ikke metalbeslagene fra panelet.
Om denne opgave 64 Adskillelse og samling
Trin 1. Placer skærmpanelet på en ren plan overflade. 2. Slut skærmkablet til stikket bagpå skærmpanelet, og luk låsen for at fastgøre kablet. 3. Påsæt tapen, der fastgør skærmkablet til bagsiden af skærmpanelet. 4. Vend skærmpanelet om, og anbring det forsigtigt på skærmens bagdæksel. 5. Genmonter de seks skruer (M2,5x2,5), der fastgør skærmpanelet til skærmens bagdæksel. Næste trin 1. 2. 3. 4. 5. 6. 7. Monter skærmrammen. Monter skærmmodulet. Monter WLAN Monter batteriet. Monter bunddækslet.
Trin 1. Kobl kamerakablet fra kameramodulet. 2. Brug en plastikpen til forsigtigt at lirke kameraet af skærmens bagdæksel og antennemodulet. Sådan monteres kameraet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages. Om denne opgave Trin 1. Brug styremærkerne til at sætte kameramodulet fast på skærmens bagdæksel og antennemodulet. 2. Tilslut kamerakablet til kameramodulet. Næste trin 1. 2. 3. 4. 5. 6. 7. 8.
Skærmens bagdæksel og antennemodul Sådan fjernes skærmens bagdæksel Forudsætninger 1. 2. 3. 4. 5. 6. 7. 8. 9. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-kortet. Fjern bunddækslet. Frakobl batterikablet. Fjern WLAN. Fjern skærmmodulet. Fjern skærmrammen. Fjern skærmpanelet. Fjern kameraet. Om denne opgave Efter udførelse af alle de ovennævnte trin er der kun skærmens bagdæksel tilbage.
Næste trin 1. 2. 3. 4. 5. 6. 7. 8. 9. Monter kameraet. Monter skærmpanelet. Monter skærmrammen. Monter skærmmodulet. Monter WLAN Tilslut batterikablet. Monter bunddækslet. Monter SD-kortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Tænd/sluk-knap Sådan fjernes tænd/sluk-knappen Forudsætninger 1. 2. 3. 4. 5. 68 Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-kortet. Fjern bunddækslet. Frakobl batterikablet. Fjern I/O-kortet.
Om denne opgave Trin 1. Fjern de to (M2x2) skruer, der fastgør tænd/sluk-knappen på håndledsstøttemodulet. 2. Kobl tænd/sluk-knapkablet fra, og fjern tænd/sluk-knappen fra systemet. Sådan monteres tænd/sluk-knappen Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Om denne opgave Trin 1. Sæt tænd/sluk-knapkortet ind i slotten på håndledsstøtten. 2. Monter de to skruer (M2x2), der fastgør tænd/sluk-knappen til håndledsstøtten. 3. Slut tænd/sluk-knappens kabel til stikket på systemkortet. Næste trin 1. 2. 3. 4. 5. Monter IO-kortet. Tilslut batterikablet. Monter bunddækslet. Monter SD-kortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Systemkort Sådan fjernes bundkortet – Realtek-lyd Forudsætninger 1. 2. 3. 4. 5. 6. 7. 8. 9.
10. Fjern kølelegemet. BEMÆRK: Systemkortet kan fjernes sammen med kølelegemet. 11. Fjern skærmsamlingen.
Om denne opgave 72 Adskillelse og samling
Trin 1. Fjern de to skruer (M2,5x5) fra det venstre hængsel, og løft hængslet op. 2. Fjern følgende kabler fra bundkortet: a. b. c. d. e. f. g. h. i. Højttalerkabel Fleksibelt fladkabel til tastatur Kabel til strømadapterport Fleksibelt fladkabel til tastaturets bagbelysning FFC-pegefelt Fleksibelt fladkabel til harddisk Fleksibelt fladkabel til IO-kort Fleksibelt fladkabel til fingeraftrykslæser Fleksibelt fladkabel til tænd/sluk-knappen fra bundkortet 3.
Trin 1. Anbring bundkortet korrekt på håndledsstøtten. 2. Fjern den enkelte skrue (M2x4), der fastgør bundkortet til håndledsstøtten. 3. Tilslut følgende kabler til bundkortet: a. b. c. d. e. f. g. h. i.
Sådan fjernes bundkortet – Cirrus Logic-lyd Forudsætninger 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-kortet. Fjern bunddækslet. Fjern batteriet. Fjern WLAN. Fjern SSD'et. Fjern harddiskmodulet. Fjern hukommelsen Fjern systemblæseren. Fjern kølelegemet. BEMÆRK: Systemkortet kan fjernes sammen med kølelegemet. 11. Fjern skærmsamlingen.
Trin 1. Fjern følgende kabler fra bundkortet: a. b. c. d. e. f. g. h. i. Højttalerkabel Fleksibelt fladkabel til tastatur Kabel til strømadapterport Fleksibelt fladkabel til tastaturets bagbelysning FFC-pegefelt Fleksibelt fladkabel til harddisk Fleksibelt fladkabel til IO-kort Fleksibelt fladkabel til fingeraftrykslæser Fleksibelt fladkabel til tænd/sluk-knappen fra bundkortet 2. Pil Mylar-tapen tilbage fra skruehullet 3. Fjern de to skruer (M2x4), der fastgør bundkortet til håndledsstøtten. 4.
Om denne opgave Adskillelse og samling 77
Trin 1. Anbring bundkortet korrekt på håndledsstøtten. 2. Pil Mylar-tapen tilbage fra skruehullet. 3. Fjern de to skruer (M2x4), der fastgør bundkortet til håndledsstøtten. 4. Tilslut følgende kabler til bundkortet: a. b. c. d. e. f. g. h. i.
3. 4. 5. 6. 7. 8. 9. 10. Monter systemblæseren. Monter hukommelsen. Monter SSD'et. Monter WLAN Monter batteriet. Monter bunddækslet. Monter SD-kortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele. Strømadapterport Sådan fjernes strømadapterporten Forudsætninger 1. 2. 3. 4. 5. 6. 7. 8. 9. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-kortet. Fjern bunddækslet. Frakobl batterikablet. Fjern WLAN. Fjern SSD'et. Fjern systemblæseren.
Trin 1. Frakobl og tag strømadapterportmodulet ud af systemkortet. 2. Fjern strømadapterportmodulet fra systemet. Sådan monteres strømadapterporten Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages. Om denne opgave Trin Sæt strømadapterportmodulet ind i slotten på håndledsstøtten. Næste trin 1. 2. 3. 4. 5. 6. 7. 8. 9. 80 Monter systemkortet. Monter skærmmodulet. Monter systemblæseren. Monter SSD'et.
Håndfladestøtte og tastaturmodul Sådan fjernes håndledsstøtte- og tastaturmodulet Forudsætninger 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-kortet. Fjern bunddækslet. Fjern batteriet. Fjern WLAN. Fjern hukommelsen Fjern skærmmodulet. Fjern SSD'et. Fjern harddiskmodulet. Fjern højtalerne. Fjern knapcellebatteriet. Fjern systemblæseren. Fjern kølelegemet. BEMÆRK: Systemkortet kan fjernes sammen med kølelegemet. 14. 15. 16. 17.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 82 Installer touchpad'en. Monter IO-kortet. Monter kølelegemet. Monter systemblæseren. Monter knapcellebatteriet. Installer højttalerne. Monter harddiskmodulet. Monter SSD'et. Monter skærmmodulet. Monter hukommelsen. Monter WLAN Monter batteriet. Monter bunddækslet. Monter SD-kortet.
6 Fejlfinding Emner: • • • Forbedret Pre-Boot System Assessment – ePSA-diagnosticering Systemdiagnosticeringsindikatorer Wi-Fi-strømcyklus Forbedret Pre-Boot System Assessment – ePSAdiagnosticering Om denne opgave SupportAssist-diagnosticeringen (også kendt som systemdiagnostik) udfører et fuldstændigt tjek af din hardware. SupportAssistdiagnosticeringen er indlejret med BIOS og lanceres af BIOS internt.
SupportAssist åbner standardskærmen ved start. Du kan skifte til avanceret skærm vha. ikonet nederst på skærmen. Avanceret skærm viser alle de registrerede enheder i fliseformat. Specifikke tests kan kun inkluderes eller ekskluderes i avanceret tilstand. Standardskærmen har minimale kontrolknapper, som muliggør nem navigation, for at brugeren kan starte eller stoppe diagnostikken. Systemdiagnosticeringsindikatorer Strøm- og batteristatusindikator Viser status for strøm og -batteriopladning.
Tabel 4. LED-koder Diagnostiske lyskoder Problembeskrivelse Anbefalede løsninger 2,6 Fejl på systemkort eller chipset Flashopdater seneste BIOS-version. Hvis problemet fortsætter, skal du udskifte systemkortet. 2,7 LCD-fejl – SBIOS-meddelelse Udskift skærmkablet (EDP) om muligt, og udskift ellers skærmmodulet (LCD). 2,8 LCD-fejl – EC-registrering af strømskinnefejl Genmonter systemkortet. 3,1 Fejl i møntcellebatteri Nulstil CMOS-batteriets tilslutning.
7 Sådan får du hjælp Emner: • Kontakt Dell Kontakt Dell Forudsætninger BEMÆRK: Hvis du ikke har en aktiv internetforbindelse, kan du finde kontaktoplysninger på din købsfaktura, pakkeseddel eller i Dells produktkatalog. Om denne opgave Dell giver flere muligheder for online- og telefonbaseret support og service. Tilgængeligheden varierer for de enkelte lande og produkter, og nogle tjenester findes muligvis ikke i dit område. Sådan kontakter du Dell omkring salg, teknisk support eller kundeservice: Trin 1.