Vostro 3501 Servicehandbok Regleringsmodell: P90F Regleringstyp: P90F002 September 2020 Rev.
Anmärkningar, försiktighetsbeaktanden och varningar OBS: OBS innehåller viktig information som hjälper dig att få ut det mesta av produkten. CAUTION: VIKTIGT anger antingen risk för skada på maskinvara eller förlust av data och förklarar hur du kan undvika problemet. VARNING: En VARNING visar på en potentiell risk för egendoms-, personskador eller dödsfall. © 2020 Dell Inc. eller dess dotterbolag. Med ensamrätt. Dell, EMC och andra varumärken är varumärken som tillhör Dell Inc. eller dess dotterbolag.
Innehåll Kapitel 1: Arbeta med datorn............................................................................................................ 6 Säkerhetsanvisningar............................................................................................................................................................ 6 Innan du arbetar inuti datorn..........................................................................................................................................
Installera knappcellsbatteriet........................................................................................................................................39 Systemfläkt.......................................................................................................................................................................... 40 Ta bort systemfläkten.........................................................................................................................................
WiFi-cykel............................................................................................................................................................................. 84 Kapitel 6: Få hjälp..........................................................................................................................85 Kontakta Dell........................................................................................................................................................................
1 Arbeta med datorn Ämnen: • Säkerhetsanvisningar Säkerhetsanvisningar Förutsättningar Följ dessa säkerhetsföreskrifter för att skydda datorn och dig själv. Om inget annat anges förutsätts i varje procedur i det här dokumentet att följande villkor har uppfyllts: ● Du har läst säkerhetsinformationen som medföljde datorn. ● En komponent kan ersättas eller – om du köper den diskret – monteras i omvänd ordning jämfört med borttagningsproceduren.
5. Ta bort eventuella mediakort och optiska skivor från datorn, om det behövs. 6. När datorn är frånkopplad håller du strömbrytaren nedtryckt i cirka fem sekunder för att jorda moderkortet. CAUTION: Placera datorn på en plan, mjuk och ren yta för att undvika repor på bildskärmen. 7. Placera datorn med framsidan nedåt. Säkerhetsföreskrifter Kapitlet om säkerhetsföreskrifter beskriver de primära stegen som ska vidtas innan du utför några demonteringsanvisningar.
● Använd ett kabelanslutet ESD-armband som är korrekt jordat. Det är inte längre tillåtet att använda trådlösa antistatiska armband eftersom de inte ger ett tillräckligt skydd. Det räcker inte med att röra vid chassit innan du hanterar delar för att få ett garanterat ESDskydd för delar med ökad ESD-känslighet. ● Hantera alla komponenter som är känsliga för statisk elektricitet på en plats som är skyddad mot elektrostatiska urladdningar. Använd om möjligt antistatiska golvplattor och skrivbordsunderlägg.
När du har arbetat inuti datorn Om denna uppgift OBS: Kvarglömda och lösa skruvar inuti datorn kan allvarligt skada datorn. Steg 1. Sätt tillbaka alla skruvar och kontrollera att inga lösa skruvar finns kvar inuti datorn. 2. Anslut eventuella externa enheter, kringutrustning och kablar som du tog bort innan arbetet på datorn påbörjades. 3. Sätt tillbaka eventuella mediakort, skivor och andra delar som du tog bort innan arbetet på datorn påbörjades. 4. Anslut datorn och alla anslutna enheter till eluttagen.
2 Teknik och komponenter I det här kapitlet beskrivs teknik och komponenter som finns i systemet. Ämnen: • • • USB-funktioner HDMI 1.4 Strömbrytare LED-beteende USB-funktioner USB (Universal Serial Bus) lanserades 1996. Det förenklade drastiskt anslutningen mellan värddatorer och kringutrustning, till exempel möss, tangentbord, externa drivrutiner och skrivare. Tabell 1. Utveckling av USB Typ Dataöverföringshastighet Kategori Introduktionsår USB 2.0 480 Mbit/s Hög hastighet 2000 USB 3.
● USB 2.0 hade tidigare fyra ledningar (ström, jord och ett ledningspar för differentiella data). Med USB 3.2 Gen 1 tillkommer ytterligare fyra, vilket ger två par för differentialsignaler (för mottagning och sändning) för en kombination av totalt åtta anslutningar i kontakter och kablar. ● USB 3.2 Gen 1 använder ett dubbelriktat datagränssnitt i stället för den lösning med halv duplex som USB 2.0 använder. Detta ger en tiofaldig ökning av den teoretiska bandbredden.
HDMI 1.4 Detta ämne förklarar HDMI 1.4 och dess funktioner tillsammans med fördelarna. HDMI (High-Definition Multimedia Interface) är ett okomprimerat, helt digitalt ljud-/videogränssnitt som stöds av branschen. HDMI ger ett gränssnitt mellan vilken kompatibel digital ljud-/videokälla som helst, t.ex. en DVD-spelare eller A/V-mottagare, och en kompatibel digital ljud- och/eller bildskärmsenhet, t.ex. en digital TV (DTV). De främsta fördelarna är att mängden kablar minskar och att innehållet skyddas.
● System-LED lyser när man trycker på strömbrytaren. ● Alla tillgängliga LED-lampor (tangentbordets bakgrundsbelysning/tangentbordslås LED/batteriladdnings LED) tänds och visar specificerat beteende. ● Den auditiva tonen är avstängd som standard. Det kan aktiveras i BIOS-inställningarna. ● Skyddsåtgärder försvinner inte om enheten hänger under inloggningsprocessen. ● Dell-logotyp: Slår på inom 2 sekunder efter att du tryckt på strömbrytaren.
○ Tabell 2.
3 Utvidgad vy 1. 2. 3. 4. 5. 6. 7. 8.
9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Högtalare Handledsstödsenhet Pekskärm Bildskärmsenhet Strömbrytarmodul IO-kort Knappcellsbatteri HDD-enhet Kylflänsenheten Fläktenhet OBS: Dell innehåller en lista över komponenter och tillhörande artikelnummer för den ursprungliga systemkonfigurationen som köpts. Dessa delar är tillgängliga enligt garantitäckningar som kunden har köpt. Kontakta din Dell-säljare för köpalternativ.
4 Isärtagning och ihopsättning Ämnen: • • • • • • • • • • • • • • • • • • • • • • SD-kort (Secure Digital) Kåpan Batteriet Minnesmoduler WLAN-kort SSD-disk Hårddisk Knappcellsbatteri Systemfläkt Kylfläns Högtalare I/O-kort Pekskärm Bildskärmsenhet Bildskärmsram Kamera Bildskärmspanelen Bildskärmens bakre kåpa och antennmontering Strömbrytare Moderkort Nätadapterport Enhet med handledsstöd och tangentbord SD-kort (Secure Digital) Ta bort SD-kortet (Secure Digital) Förutsättningar 1.
Om denna uppgift Steg 1. Tryck på-SD-kortet för att lossa det från datorn. 2. För ut-SD-kortet från datorn. Installera SD-kortet (Secure Digital) Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren.
Om denna uppgift Steg För in-SD-kortet i kortplatsen tills det klickar på plats. Nästa Steg 1. Följ anvisningarna i när du har arbetat inuti datorn Kåpan Ta bort baskåpan Förutsättningar 1. Följ anvisningarna i innan du arbetar inuti datorn. 2. Ta bort SD-kortet.
Om denna uppgift 20 Isärtagning och ihopsättning
Steg 1. Ta bort de sju skruvarna (M2,5x6) och lossa de två fästskruvarna från baskåpan. 2. Bänd upp baskåpan med början från urtagen som finns i de U-formade inskärningarna vid baskåpans övre kant nära gångjärnen. OBS: Varning! Bänd INTE upp från kanten nära ventilerna på den övre sidan av baskåpan eftersom det kan skada kåpan. 3. Lyft den övre delen av baskåpan och ta bort den från systemet.
Om denna uppgift 22 Isärtagning och ihopsättning
Steg 1. Rikta in och placera baskåpan på datorn, tryck på kanterna och sidorna av baskåpan tills det hoppar på plats. 2. Byt ut de sju (M2,5x6) skruvarna och de två fästskruvarna för att fästa kåpan på datorn. Nästa Steg 1. Sätt tillbaka SD-kortet 2. Följ anvisningarna i när du har arbetat inuti datorn Batteriet Försiktighetsåtgärder gällande litiumjonbatterier CAUTION: ● Var försiktig när du hanterar litiumjonbatterier. ● Ladda ur batteriet så mycket som möjligt innan du tar bort det från datorn.
Om denna uppgift Steg 1. Dra av tejpen som täcker batterikontakten. 2. Koppla loss batterikabeln från kontakten på moderkortet. Återansluta batteriet Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren.
Om denna uppgift Steg 1. Anslut batterikabeln till kontakten på moderkortet. 2. Sätt tillbaka tejpen som täcker batterikontakten. Nästa Steg 1. Installera baskåpan. 2. Installera SD-kortet. 3. Följ anvisningarna i när du har arbetat inuti datorn. Ta bort batteriet Förutsättningar 1. Följ anvisningarna i innan du arbetar inuti datorn. 2. Ta bort SD-kortet. 3. Ta bort baskåpan.
Om denna uppgift Steg 1. Ta bort de tre (M2x3) skruvarna som fäster batteriet på handledsstödet. 2. Lyft upp och ta bort batteriet från datorn. Installera batteriet Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren.
Om denna uppgift Steg 1. Rikta in flikarna på batteriet mot urtagen på handledsstödet. OBS: När du installerar batteriet i systemet ska du sätta i fliken i det nedre vänstra hörnet av batteriet i kroken på undersidan av handledsstödet. 2. Sätt tillbaka de tre skruvarna (M2x3) som håller fast batteriet på handledsstödet. 3. Anslut batterikabeln till kontakten på moderkortet.
3. Följ anvisningarna i när du har arbetat inuti datorn. Minnesmoduler Ta bort minnesmodulen Förutsättningar 1. 2. 3. 4. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort SD-kortet. Ta bort baskåpan. Koppla bort batterikabeln. Om denna uppgift Steg 1. Bänd i klämmorna som håller fast minnesmodulen tills minnesmodulen hoppar upp. 2. Ta bort minnesmodulen från minnesmodulkortplatsen.
Om denna uppgift Steg 1. Rikta in spåret på minnesmodulen med fliken på minnesmodulens fack och skjut in minnesmodulen ordentligt i facket i en vinkel. 2. Tryck sedan minnesmodulen nedåt tills klämmorna håller fast den. OBS: Om du inte hör något klick tar du bort minnesmodulen och försöker igen. Nästa Steg 1. 2. 3. 4. Anslut batterikabeln. Installera baskåpan. Installera SD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. WLAN-kort Ta bort WLAN-kortet Förutsättningar 1. 2. 3. 4.
Om denna uppgift Steg 1. Ta bort den enda skruven (M2x3) som håller fast WLAN-kortet på moderkortet. 2. För ut och ta bort WLAN-kortets fäste som håller fast WLAN-antennkablarna. 3. Koppla ur WLAN-antennkablarna från kontakterna på WLAN-kortet. 4. Dra ut WLAN-kortet från M.2-porten på moderkortet. Installera WLAN-kortet Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren.
Om denna uppgift Steg 1. Sätt tillbaka WLAN-kortet i M.2-kortplatsen på moderkortet. 2. Anslut WLAN-antennkablarna till kontakterna på WLAN-kortet. 3. Sätt i WLAN-kortfästet för att fästa WLAN-kablarna på WLAN-kortet. 4. Sätt tillbaka den enda skruven (M2x3) som håller fast WLAN-fästet på handledsstödet. Nästa Steg 1. 2. 3. 4. Anslut batterikabeln. Installera baskåpan. Installera SD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. SSD-disk Ta bort M.2 2230 SSD-disken Förutsättningar 1.
3. Ta bort baskåpan. 4. Koppla bort batterikabeln. Om denna uppgift Steg 1. Ta bort den enda skruven (M2x2,2) och den enda fästskruven som håller fast SSD-diskens termiska platta på handledsstödet och lyft ut den ur systemet. 2. Vänd på den termiska plattan och ta bort den enda skruven (M2x2) som håller fast M.2 2230 SSD-disken på den termiska plattan. 3. Lyft bort SSD-disken från den termiska plattan. Installera M.
Om denna uppgift Steg 1. Placera SSD-disken i den termiska plattan och installera den enda skruven (M2x2). 2. För in och sätt fast fliken på SSD-disken på kortplatsen för SSD-disken. 3. Sätt tillbaka den enda (M2x2,2) skruven och dra åt den enda fästskruven för att fästa den termiska plattan på handledsstödet. Nästa Steg 1. 2. 3. 4. Anslut batterikabeln. Installera baskåpan. Installera SD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. Ta bort M.2 2280 SSD-disken Förutsättningar 1. 2. 3. 4.
Om denna uppgift Steg 1. Ta bort den enda skruven (M2x2,2) och den enda fästskruven från det termiska fästet och lyft ut fästet ur systemet. 2. Lyft upp SSD-disken från M.2-platsen på moderkortet och ta bort den från systemet. Installera M.2 2280 SSD-disken Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren.
Om denna uppgift Steg 1. Skjut i SSD-disken i M.2-porten på moderkortet. 2. Placera det termiska fästet på SSD-disken, sätt tillbaka den enda skruven (M2x2,2) och dra åt fästskruven för att fästa den termiska plattan på handledsstödet. Nästa Steg 1. 2. 3. 4. Anslut batterikabeln. Installera baskåpan. Installera SD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. Hårddisk Ta bort hårddiskenhet Förutsättningar 1. 2. 3. 4. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort SD-kortet.
Om denna uppgift Steg 1. Lyft spärren och koppla bort hårddiskkabeln från moderkortet. 2. Ta bort de tre skruvarna (M2x3) som håller fast hårddiskenheten på handledsstödet och lyft upp hårddiskenheten tillsammans med kabeln från systemet. 3. Koppla loss mellandelen (interposer) från hårddisken. 4. Ta bort de fyra skruvarna (M3x3) från hårddiskhållaren för att lossa hårddisken.
Om denna uppgift Steg 1. Rikta in hårddisken med hårddiskhållaren och sätt tillbaka de fyra skruvarna (M3x3). 2. Anslut medlingskortet (interposer) till hårddisken. 3. Rikta in och placera hårddiskenheten på handledsstödet och sätt tillbaka de tre skruvarna (M2x3) som håller fast hårddiskenheten på handledsstödet. 4. Anslut hårddiskkabeln till moderkortet och stäng spärren så att kabeln sitter fast ordentligt. Nästa Steg 1. 2. 3. 4. Installera batteriet. Installera baskåpan. Installera SD-kortet.
Knappcellsbatteri Ta bort knappcellsbatteriet Förutsättningar 1. 2. 3. 4. 5. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort SD-kortet. Ta bort baskåpan. Koppla bort batterikabeln. Ta bort I/O-kortet. Om denna uppgift Steg 1. Använd en plastrits och bänd försiktigt upp knappcellsbatteriet från platsen på IO-dotterkortet. 2. Ta ut knappcellsbatteriet från IO-dotterkortet.
Installera knappcellsbatteriet Om denna uppgift Steg 1. Vänd den positiva sidan uppåt och för in knappcellsbatteriet i batteriplatsen på I/O-kortet. 2. Tryck på batteriet tills det klickar på plats. Nästa Steg 1. 2. 3. 4. Installera IO-kortet. Anslut batterikabeln. Installera baskåpan. Installera SD-kortet.
5. Följ anvisningarna i när du har arbetat inuti datorn. Systemfläkt Ta bort systemfläkten Förutsättningar 1. 2. 3. 4. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort SD-kortet. Ta bort baskåpan. Koppla bort batterikabeln. Om denna uppgift Steg 1. Koppla bort fläktkabeln från kontakten på moderkortet. 2. Ta bort de två (M2,5x5) skruvarna som fäster fläkten vid handledsstödet.
Om denna uppgift Steg 1. Justera och placera fläkten på handledsstödet. 2. Sätt tillbaka de två skruvarna (M2,5x5) som håller fast fläkten på handledsstödet. 3. Anslut fläktkabeln till kontakten på moderkortet. Nästa Steg 1. Sätt tillbaka batterikabeln.
2. Sätt tillbaka kåpan. 3. Sätt tillbaka SD-kortet. 4. Följ anvisningarna i när du har arbetat inuti datorn. Kylfläns Ta bort kylflänsen Förutsättningar 1. 2. 3. 4. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort SD-kortet. Ta bort baskåpan. Koppla bort batterikabeln. Om denna uppgift Steg 1. Lossa de fyra fästskruvarna som håller fast kylflänsen i moderkortet. 2. Lyft bort kylflänsen från moderkortet.
Om denna uppgift Steg 1. Placera kylflänsen på moderkortet och rikta in fästskruvarna på kylflänsen med skruvhålen på moderkortet. 2. Dra åt de fyra fästskruvarna för att fästa kylflänsen på moderkortet. Nästa Steg 1. 2. 3. 4. Sätt tillbaka batterikabeln. Installera baskåpan. Installera SD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. Högtalare Ta bort högtalarna Förutsättningar 1. 2. 3. 4. 5. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort SD-kortet. Ta bort baskåpan.
Om denna uppgift Steg 1. Koppla bort högtalarkabeln från moderkortet. 2. Trä ut och ta bort högtalarkabeln från kabelhållarna på handledsstödet. 3. Lyft bort högtalarna, tillsammans med kabeln, från systemet. Installera högtalarna Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. Om denna uppgift OBS: Om gummitågringarna trycks ut när du tar bort högtalarna, trycka tillbaka dem innan du sätta tillbaka högtalarna.
Steg 1. Använd justeringstapparna och gummitågringarna för att placera högtalarna i facken på handledsstödet. 2. Dra högtalarkabeln genom kabelhållarna på handledsstödet. 3. Anslut högtalarkabeln till kontakten på moderkortet. Nästa Steg 1. 2. 3. 4. 5. Installera SSD. Sätt tillbaka batterikabeln. Installera baskåpan. Installera SD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. I/O-kort Ta bort IO-kortet Förutsättningar 1. 2. 3. 4. Följ anvisningarna i innan du arbetar inuti datorn.
Om denna uppgift Steg 1. [För modeller som levereras med fingeravtrycksläsare]: koppla bort fingeravtrycksläsaren till I/O-dotterkortets flatkabel och I/Odotterkortet till moderkortets flatkabel från I/O-dotterkortet. 2. [För modeller som levereras utan fingeravtrycksläsare]: koppla bort strömbrytarens flatkabel, I/O-dotterkortets flatkabel och bildskärmskabeln från moderkortet. 3. Dra tillbaka strömbrytarens flatkabel och IO-dotterkortets flatkabel från handledsstödet. 4.
Om denna uppgift Steg 1. Återanslut strömbrytarens flatkabel och I/O-dotterkortets flatkabel till I/O-dotterkortet. 2. Placera I/O-dotterkortet på systemet. 3. Sätt tillbaka de tre (M2x4) skruvarna som håller fast I/O-dotterkortet på handledsstödet. 4. [För modeller som levereras utan fingeravtrycksläsare]: Anslut strömbrytarens flatkabel, I/O-dotterkortets flatkabel och bildskärmskabeln till kontakterna på moderkortet. 5.
2. Ta bort SD-kortet. 3. Ta bort baskåpan. 4. Ta bort batteriet. Om denna uppgift Steg 1. Koppla bort pekskärmens flatkabel från moderkortet. 2. Dra bort den ledande tejpen från pekplattan. 3. Ta bort de tre skruvarna (M2x2) som håller fast pekplattans fäste. 4. Ta bort pekplattans fäste från systemet. 5. Ta bort de två skruvarna (M2x2) som håller pekplattan på plats. 6. Ta bort pekplattan med pekplattans flatkabel från systemet. 7. Koppla bort pekplattans flatkabel från pekplattan.
Steg 1. Återanslut pekplattans flatkabel till pekplattan. 2. Rikta in och placera pekplattans modul på systemet. 3. Sätt tillbaka de två skruvarna (M2x2) för att fästa pekplattans modul på handledsstödet 4. Montera fästet för pekplattan på pekplattan och säkra det med de tre skruvarna (M2x2). 5. Dra tillbaka den ledande tejpen över pekplattan. 6. Anslut pekplattans flatkabel till moderkortet. Nästa Steg 1. 2. 3. 4. Installera batteriet. Installera baskåpan. Installera SD-kortet.
Om denna uppgift 50 Isärtagning och ihopsättning
Steg 1. Koppla bort bildskärmskabeln från kontakten på moderkortet. 2. Trä ut bildskärmskabeln och WLAN-antennkablarna från kabelkanalerna. 3. Öppna systemet åtminstone 90 grader och placera det på kanten av ett bord så att handledsstödet ligger platt på bordet och bildskärmen är över kanten. 4. Lossa de sex skruvarna (M2,5x6) som håller bildskärmsenheten på plats. 5. Ta bort bildskärmsenheten från systemet.
Steg 1. Justera och placera systemet under gångjärnen på bildskärmsenheten. 2. Montera de sex skruvarna (M2,5x6) på gångjärnen för att fästa bildskärmen på systemets chassi. 3. Dra bildskärmskabeln och WLAN-antennkablarna genom kabelhållarna på handledsstödet. 4. Anslut bildskärmskabeln till kontakten på moderkortet. Nästa Steg 1. 2. 3. 4. Installera WLAN. Installera baskåpan. Installera SD-kortet. Följ anvisningarna i när du har arbetat inuti datorn.
Om denna uppgift Steg 1. Bänd för att öppna bildskärmsramen från den inre kanten på den vänstra och högra sidan av bildskärmsenheten. 2. Bänd för att öppna bildskärmsramen från den inre kanten på ovansidan av bildskärmsenheten.
3. Bänd för att öppna gångjärnskåpan på undersidan av bildskärmsenheten. 4. Bänd för att öppna bildskärmsramen från den inre kanten på undersidan av bildskärmsenheten.
5. Lyft och ta bort bildskärmsramen från bildskärmsenheten. OBS: Varning! Använd inte en rits eller några andra föremål för att bända upp bildskärmsramen på det sätt som visas i bilderna nedan eftersom trycket från ritsen på bildskärmspanelen skadar bildskärmspanelen.
Installera bildskärmsramen Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. Om denna uppgift Steg Passa in bildskärmsramen med bildskärmens bakre kåpa och antennenhet och knäpp sedan försiktigt bildskärmsramen på plats. Nästa Steg 1. 2. 3. 4. 5. Installera bildskärmsenheten. Sätt tillbaka batterikabeln. Installera baskåpan. Installera SD-kortet. Följ anvisningarna i när du har arbetat inuti datorn.
6. Ta bort bildskärmsenheten. 7. Ta bort bildskärmsramen. 8. Ta bort bildskärmspanelen. Om denna uppgift Steg 1. Koppla bort kamerakabeln från kameramodulen. 2. Använd en plastrits och bänd försiktigt bort kameran från bildskärmens bakre kåpa och antennenhet. Installera kameran Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren.
Om denna uppgift Steg 1. Använd justeringstapparna och fäst kameramodulen på bildskärmens bakre hölje och antennenheten. 2. Anslut kamerakabeln till kameramodulen. Nästa Steg 1. 2. 3. 4. 5. 6. 7. 8. Installera bildskärmspanelen. Installera bildskärmsramen. Installera bildskärmsenheten. Installera WLAN. Anslut batterikabeln. Installera baskåpan. Installera SD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. Bildskärmspanelen Ta bort bildskärmspanelen Förutsättningar 1. 2. 3. 4. 5. 6. 7.
Om denna uppgift Isärtagning och ihopsättning 59
Steg 1. Ta bort de sex skruvarna (M2,5x2,5) och de två skruvarna (M2x2,5) som håller fast bildskärmspanelen på gångjärnen. 2. Vänd försiktigt på bildskärmspanelen och dra bort mylartejpen som håller fast bildskärmskabeln på baksidan av bildskärmspanelen. OBS: Se till att panelen har en ren och jämn yta att ligga på för att förhindra skador. 3. Koppla bort bildskärmskabeln från moderkortet och ta bort bildskärmspanelen från systemet. OBS: Ta inte bort metallfästena från panelen.
Om denna uppgift Isärtagning och ihopsättning 61
Steg 1. Placera bildskärmspanelen på en plan och ren yta. 2. Anslut bildskärmskabeln till kontakten på bildskärmspanelens baksida och stäng spärren så att kabeln sitter fast. 3. Sätt fast tejpen som håller fast bildskärmskabeln på baksidan av bildskärmspanelen. 4. Vänd på bildskärmspanelen och placera den på bildskärmskåpan. 5. Sätt tillbaka de sex (M2x2,5) och två (M2,5x2,5) skruvarna som håller fast bildskärmspanelen i bildskärmens bakre kåpa. Nästa Steg 1. 2. 3. 4. 5. 6. 7. 8.
Ta bort bildskärmens bakre kåpa Om denna uppgift Placera bildskärmens bakre kåpa på en ren och plan yta. Nästa Steg 1. Installera bildskärmspanelen. 2. Installera bildskärmsramen.
3. 4. 5. 6. 7. 8. Installera bildskärmsenheten. Installera WLAN. Anslut batterikabeln. Installera baskåpan. Installera SD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. Kamera Ta bort kameran Förutsättningar 1. 2. 3. 4. 5. 6. 7. 8. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort SD-kortet. Ta bort baskåpan. Koppla bort batterikabeln. Ta bort WLAN. Ta bort bildskärmsenheten. Ta bort bildskärmsramen. Ta bort bildskärmspanelen. Om denna uppgift Steg 1.
Installera kameran Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. Om denna uppgift Steg 1. Använd justeringstapparna och fäst kameramodulen på bildskärmens bakre hölje och antennenheten. 2. Anslut kamerakabeln till kameramodulen. Nästa Steg 1. 2. 3. 4. 5. 6. 7. 8. Installera bildskärmspanelen. Installera bildskärmsramen. Installera bildskärmsenheten. Installera WLAN. Anslut batterikabeln. Installera baskåpan. Installera SD-kortet.
5. Ta bort WLAN. 6. Ta bort bildskärmsenheten. 7. Ta bort bildskärmsramen.
Om denna uppgift Isärtagning och ihopsättning 67
Steg 1. Ta bort de sex skruvarna (M2,5x2,5) och de två skruvarna (M2x2,5) som håller fast bildskärmspanelen på gångjärnen. 2. Vänd försiktigt på bildskärmspanelen och dra bort mylartejpen som håller fast bildskärmskabeln på baksidan av bildskärmspanelen. OBS: Se till att panelen har en ren och jämn yta att ligga på för att förhindra skador. 3. Koppla bort bildskärmskabeln från moderkortet och ta bort bildskärmspanelen från systemet. OBS: Ta inte bort metallfästena från panelen.
Om denna uppgift Isärtagning och ihopsättning 69
Steg 1. Placera bildskärmspanelen på en plan och ren yta. 2. Anslut bildskärmskabeln till kontakten på bildskärmspanelens baksida och stäng spärren så att kabeln sitter fast. 3. Sätt fast tejpen som håller fast bildskärmskabeln på baksidan av bildskärmspanelen. 4. Vänd på bildskärmspanelen och placera den på bildskärmskåpan. 5. Sätt tillbaka de sex (M2x2,5) och två (M2,5x2,5) skruvarna som håller fast bildskärmspanelen i bildskärmens bakre kåpa. Nästa Steg 1. 2. 3. 4. 5. 6. 7. 8.
Ta bort bildskärmens bakre kåpa Om denna uppgift Placera bildskärmens bakre kåpa på en ren och plan yta. Nästa Steg 1. Installera bildskärmspanelen.
2. 3. 4. 5. 6. 7. 8. Installera bildskärmsramen. Installera bildskärmsenheten. Installera WLAN. Anslut batterikabeln. Installera baskåpan. Installera SD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. Strömbrytare Ta bort strömbrytaren Förutsättningar 1. 2. 3. 4. 5. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort SD-kortet. Ta bort baskåpan. Koppla bort batterikabeln. Ta bort I/O-kortet. Om denna uppgift Steg 1.
Installera strömbrytaren Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. Om denna uppgift OBS: När du byter ut/sätter tillbaka strömbrytaren med fingeravtrycksläsaren på Vostro 3501 måste en mylardekal fästas på fingeravtrycksläsaren FPC för att säkerställa att den är ordentligt jordad till handledsstödet. Mylardekalen paketeras tillsammans med en ny utbytesströmbrytare med fingeravtrycksläsarenheter Steg 1.
Moderkort Ta bort moderkortet Förutsättningar 1. 2. 3. 4. 5. 6. 7. 8. 9. Följ anvisningarna i innan du arbetar inuti datorn Ta bort SD-kortet. Ta bort baskåpan. Ta bort batteriet. Ta bort WLAN. Ta bort SSD Ta bort minnet. Ta bort systemfläkten. Ta bort kylflänsen. OBS: Moderkortet kan tas bort tillsammans med kylflänsen. 10. Ta bort bildskärmsenheten.
Om denna uppgift Isärtagning och ihopsättning 75
Steg 1. Koppla bort följande kablar från moderkortet: a. b. c. d. e. f. g. h. i. Högtalarkabel Tangentbordets flatkabel Nätadapterportens kabel Tangentbordsbelysning med flatkabel Pekplattans flatkabel Hårddiskens flatkabel IO-kortets flatkabel Fingeravtrycksläsarens flatkabel strömbrytarens flatkabel från moderkortet 2. Ta bort den enda skruven (M2x4) som håller fast moderkortet på handledsstödet. 3. Lyft försiktigt bort moderkortet från chassit.
Om denna uppgift Steg 1. Justera och placera systemkortet på handledsstödet. 2. Sätt tillbaka den enda skruven (M2x4) som håller fast moderkortet på handledsstödet. 3. Anslut följande kablar till moderkortet: a. b. c. d. e. f. g.
h. Fingeravtrycksläsarens flatkabel i. Strömbrytarens flatkabel från moderkortet 4. Vik höger gångjärn bakåt och montera de två skruvarna (M2,5x5) som håller fast det på handledsstödet. Nästa Steg 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Installera bildskärmsenheten. Installera kylflänsen. Installera systemfläkten. Installera minnet. Installera SSD. Installera WLAN. Installera batteriet. Installera baskåpan. Installera SD-kortet. Följ anvisningarna i när du har arbetat inuti datorn.
Om denna uppgift Steg 1. Koppla bort och trä ut nätadapterns portmodul från moderkortet. 2. Ta bort nätadapterns portmodul från systemet. Installera nätadapterporten Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren.
Om denna uppgift Steg Sätt nätaggregatets portmodul på plats i handledsstödet. Nästa Steg 1. 2. 3. 4. 5. 6. 7. 8. 9. Installera moderkortet. Installera bildskärmsenheten. Installera systemfläkten. Installera SSD. Installera WLAN. Anslut batterikabeln. Installera baskåpan. Installera SD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. Enhet med handledsstöd och tangentbord Ta bort handledsstöds- och tangentbordsmonteringen Förutsättningar 1. 2. 3. 4. 5. 6. 7. 8.
9. 10. 11. 12. 13. Ta bort hårddiskenheten Ta bort högtalarna. Ta bort knappcellsbatteriet. Ta bort systemfläkten. Ta bort kylflänsen. OBS: Moderkortet kan tas bort tillsammans med kylflänsen. 14. 15. 16. 17. Ta bort I/O-kortet. Ta bort pekplattan. Ta bort nätaggregatporten. Ta bort moderkortet. Om denna uppgift OBS: Systemkortet kan tas bort och installeras tillsammans med dissipatorn fortfarande fäst.
5 Felsökning Ämnen: • • • Förbättrad systemutvärderingsdiagnostik före start (ePSA) Systemets diagnosindikatorer WiFi-cykel Förbättrad systemutvärderingsdiagnostik före start (ePSA) Om denna uppgift SupportAssist-diagnostiken (även kallad systemdiagnostik) utför en fullständig kontroll av din maskinvara. SupportAssist-diagnostiken är inbäddad med BIOS och lanseras av BIOS internt.
SupportAssist öppnar grundskärmen vid start. Du kan växla till avancerad skärm med hjälp av ikonen längst ned till vänster på skärmen. Den avancerade skärmen visar upptäckta enheter i ett rutformat. Specifika test kan inkluderas eller uteslutas endast i avancerat läge. Grundskärmen har minimala kontroller som möjliggör enkel navigering för användaren att starta eller stoppa diagnostiken. Systemets diagnosindikatorer Kort för ström/batteristatuslampa Indikerar status för ström och batteriladdning.
Tabell 3. LED-koder (fortsättning) Diagnostikindikatorkoder Problembeskrivning Rekommenderade lösningar 2,7 LCD fel – SBIOS-meddelande Sätt tillbaka bildskärmskabeln (EDP) om det går, annars byter du ut bildskärmsenheten (LCD). 2,8 LCD-fel - EC-detektering av strömskenefel Sätt tillbaka moderkortet. 3,1 Fel på knappcellsbatteriet Återställ batteriets anslutning för CMOSbatteriet. Om problemet kvarstår, byt ut RTCbatteriet. 3,2 Fel på PCI/grafikkort/krets Sätt tillbaka moderkortet.
6 Få hjälp Ämnen: • Kontakta Dell Kontakta Dell Förutsättningar OBS: Om du inte har en aktiv Internet-anslutning kan du hitta kontaktinformationen på ditt inköpskvitto, förpackning, faktura eller i Dells produktkatalog. Om denna uppgift Dell erbjuder flera alternativ för support och service online och på telefon. Tillgängligheten varierar beroende på land och produkt och vissa tjänster kanske inte finns i ditt område.