Dell Vostro 15–3559 Benutzerhandbuch Vorschriftenmodell: P52F Vorschriftentyp: P52F003
Anmerkungen, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG liefert wichtige Informationen, mit denen Sie den Computer besser einsetzen können. VORSICHT: Ein VORSICHTSHINWEIS macht darauf aufmerksam, dass bei Nichtbefolgung von Anweisungen eine Beschädigung der Hardware oder ein Verlust von Daten droht, und zeigt auf, wie derartige Probleme vermieden werden können.
Inhaltsverzeichnis 1 Arbeiten am Computer.........................................................................................5 Vor der Arbeit an Komponenten im Innern des Computers............................................................... 5 Empfohlene Werkzeuge........................................................................................................................6 Ausschalten des Computers..............................................................................................
Einsetzen der Bildschirmblende......................................................................................................... 28 Entfernen der Kamera......................................................................................................................... 28 Einbauen der Kamera..........................................................................................................................29 Entfernen der Bildschirmscharniere..................................................
Arbeiten am Computer 1 Vor der Arbeit an Komponenten im Innern des Computers Die folgenden Sicherheitshinweise schützen den Computer vor möglichen Schäden und dienen der persönlichen Sicherheit des Benutzers. Wenn nicht anders angegeben, ist bei jedem in diesem Dokument beschriebenen Vorgang darauf zu achten, dass die folgenden Bedingungen erfüllt sind: • Sie haben die im Lieferumfang des Computers enthaltenen Sicherheitshinweise gelesen.
Um Schäden am Computer zu vermeiden, führen Sie folgende Schritte aus, bevor Sie mit den Arbeiten im Computerinneren beginnen. 1. Stellen Sie sicher, dass die Arbeitsoberfläche eben und sauber ist, damit die Computerabdeckung nicht zerkratzt wird. 2. Schalten Sie den Computer aus (siehe „Ausschalten des Computers“). 3. Falls der Computer mit einem Docking-Gerät verbunden ist, trennen Sie die Verbindung.
– Verwenden eines Touch-fähigen Geräts: a. Wischen Sie ausgehend von der rechten Seite über den Bildschirm, öffnen Sie das Charms-Menü und wählen Sie Einstellungen. b. Wählen Sie das aus und wählen Sie dann Herunterfahren – Verwenden einer Maus: • a. Fahren Sie mit dem Mauszeiger über die rechte obere Ecke des Bildschirms und klicken Sie auf Einstellungen. b. Klicken Sie auf das Symbol und wählen Sie Herunterfahren. Unter Windows 7: 1. Klicken Sie auf Start (Start) 2.
Entfernen und Einbauen von Komponenten 2 Dieser Abschnitt bietet detaillierte Informationen über das Entfernen und Einbauen von Komponenten Ihres Computers. Entfernen des Akkus 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Schieben Sie die Entriegelungsriegel zum Entriegeln des Akkus nach außen. 3. Entfernen Sie den Akku aus dem Computer.
Einsetzen des Akkus 1. Schieben Sie den Akku in den entsprechenden Steckplatz, bis er hörbar einrastet. 2. Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen des optischen Laufwerks 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie den Akku. 3. Führen Sie folgende Schritte wie in der Abbildung gezeigt durch: a.
4. Entfernen Sie die Abdeckung vom Computer. Einbauen der Abdeckung 1. Platzieren Sie die Abdeckung so, dass sie an den Schraubenbohrungen auf der Rückseite des Computers ausgerichtet ist. 2. Ziehen Sie die Schrauben fest, um die Abdeckung am Computer zu befestigen. 3. Bauen Sie den Akku ein. 4. Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen des Festplattenlaufwerks 1.
a. Trennen Sie das Festplattenkabel von der Systemplatine und heben Sie das Kabel nach oben, um es vom Computer zu entfernen [1,2]. b. Entfernen Sie die Schrauben, mit denen das Festplattenlaufwerk am Computer befestigt ist [3]. 4. Führen Sie folgende Schritte wie in der Abbildung gezeigt durch: a. Heben Sie das Festplattenlaufwerk, um es vom Computer zu entfernen [1,2]. 5. Führen Sie folgende Schritte wie in der Abbildung gezeigt durch: a.
Einsetzen des Festplattenlaufwerks 1. Setzen Sie das Festplattenlaufwerk in die Festplattenlaufwerkhalterung ein. 2. Ziehen Sie die Schrauben fest, mit denen das Festplattenlaufwerk an der Festplattenlaufwerkhalterung befestigt ist. 3. Schieben Sie die Festplatte in den Anschluss. 4. Ziehen Sie die Schraube fest, um es am Gehäuse zu befestigen. 5. Bauen Sie folgende Komponenten ein: a. Abdeckung b. Akku 6. Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
Einbauen des Speichermoduls 1. Setzen Sie das Speichermodul in den Sockel ein und drücken Sie ihn nach unten, damit die Sicherungsklammern einrasten. 2. Bauen Sie folgende Komponenten ein: a. Abdeckung b. Akku 3. Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen der WLAN-Karte 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie: a. Akku b. Abdeckung 3.
a. Akku b. Abdeckung 3. Drücken Sie mit einem Plastikstift auf den Entriegelungsriegel der Knopfzellenbatterie und ziehen Sie die Knopfzellenbatterie aus dem Computer heraus. Einbauen der Knopfzellenbatterie 1. Setzen Sie die Knopfzellenbatterie ein und drücken Sie sie nach unten, damit sie einrastet. 2. Bauen Sie folgende Komponenten ein: a. Abdeckung b. Akku 3. Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen der Tastatur 1.
4. Führen Sie folgende Schritte wie in der Abbildung gezeigt durch: a. Schieben und heben Sie die Tastatur, um auf das Tastaturanschlusskabel darunter zuzugreifen [1,2]. 5. Führen Sie folgende Schritte wie in der Abbildung gezeigt durch: a. Trennen Sie das Tastaturkabel von der Systemplatine [1]. b. Heben Sie das Tastaturkabel an, um es vom Computer zu entfernen [2]. Einsetzen der Tastatur 1. Schließen Sie das Tastaturkabel an den Anschluss auf der Systemplatine an. 2.
Entfernen der Bodenabdeckung 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie: a. b. c. d. e. f. g. 3. Akku Festplattenlaufwerk Abdeckung Optisches Laufwerk WLAN-Karte Speichermodul Tastatur Führen Sie folgende Schritte wie in der Abbildung gezeigt durch: a. Trennen Sie den Anschluss des optischen Laufwerks und heben Sie ihn an, um ihn von der Systemplatine zu entfernen [1,2]. b.
5. Führen Sie folgende Schritte wie in der Abbildung gezeigt durch: a. Drehen Sie den Computer um und entfernen Sie die Schrauben an der Unterseite des Computers [1]. b. Lösen Sie die Halterungen, mit denen die Bodenabdeckung befestigt ist [2]. c. Hebeln Sie die Bodenabdeckung an und schieben Sie sie vom Computer weg [3]. Einsetzen der Abdeckung an der Unterseite 1. Setzen Sie die Bodenabdeckung auf das Gehäuse und drücken Sie auf die Kerben, bis sie einrasten. 2.
b. c. d. e. f. g. 6. Speichermodul Festplattenlaufwerk WLAN-Karte Abdeckung Optisches Laufwerk Akku Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen der Eingabe/Ausgabe-Platine (E/A-Platine) 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie: a. b. c. d. e. f. g. 3.
Einsetzen der Eingabe/Ausgabe-Platine (E/A-Platine) 1. Verbinden Sie das Kabel der E/A-Karte mit der Systemplatine. 2. Setzen Sie die E/A-Platine in das Gehäuse ein. 3. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. h. 4. Bodenabdeckung Tastatur Speichermodul Festplattenlaufwerk WLAN-Karte Abdeckung Optisches Laufwerk Akku Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen der Kühlkörperbaugruppe 1.
4. Entfernen Sie die Kühlkörperbaugruppe von der Systemplatine. Einbauen der Kühlkörperbaugruppe 1. Setzen Sie den Kühlkörper ein und ziehen Sie die Schrauben fest, um ihn an der Systemplatine zu befestigen. 2. Verbinden Sie das Systemlüfterkabel mit der Systemplatine. 3. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. h. 4.
Entfernen der Lautsprecher 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie: a. b. c. d. e. f. g. Akku Optisches Laufwerk Abdeckung Festplattenlaufwerk Speichermodul Tastatur Bodenabdeckung 3. Lösen Sie die Lautsprecherkabel aus den Rückhalteklammern. 4. Heben Sie die Lautsprecher an und nehmen Sie sie aus dem Gehäuse.
Einbauen der Lautsprecher 1. Setzen Sie die Lautsprecher in das Gehäuse ein und drücken Sie auf die Halteklammern, damit sie einrasten. 2. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. h. 3. Bodenabdeckung Tastatur Speichermodul Festplattenlaufwerk WLAN-Karte Abdeckung Optisches Laufwerk Akku Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen der Systemplatine 1.
a. Heben Sie die Verriegelungsklammer [1]. b. Trennen Sie die Kabel der Bildschirmbaugruppe [2]. c. Lösen Sie das Kabel der Bildschirmbaugruppe [3]. 5. Führen Sie folgende Schritte wie in der Abbildung gezeigt durch: a. Entfernen Sie die Schraube, mit der der Stromversorgungsanschluss am Computer befestigt ist [1]. b. Lösen Sie das Netzanschlusskabel [2]. 6. Führen Sie folgende Schritte wie in der Abbildung gezeigt durch: a. Entfernen die Schraube, mit der die Systemplatine am Gehäuse befestigt ist [1].
Einbauen der Systemplatine 1. Setzen Sie die Systemplatine in das Gehäuse ein. 2. Ziehen Sie die Schrauben fest, um die Systemplatine am Computer zu befestigen. 3. Schließen Sie den Stromversorgungsanschluss an die Systemplatine an. 4. Schließen Sie das Bildschirmbaugruppenkabel an die Systemplatine an. 5. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. h. 6.
3. Trennen Sie den Stromanschluss von der Systemplatine und heben Sie ihn von der Systemplatine. Installieren des Stromanschlusses 1. Schließen Sie den Stromversorgungsanschluss an seinen Steckplatz am Gehäuse an und führen Sie das Kabel durch die Rückhalteklammern. 2. Verbinden Sie das Netzanschlusskabel mit der Systemplatine. 3. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. h. 4.
4. Entfernen Sie die Scharnierschrauben, mit denen die Bildschirmbaugruppe am Computer befestigt ist. 5. Führen Sie folgende Schritte wie in der Abbildung gezeigt durch: a. Heben Sie die Bildschirmbaugruppe [1]. b. Schieben Sie die Bildschirmbaugruppe in die angegebene Richtung, um sie aus dem Gehäuse zu entfernen [2].
Einsetzen der Bildschirmbaugruppe 1. Richten Sie die Bildschirmbaugruppe am Gehäuse aus. 2. Verlegen Sie das WLAN- und das Kabel der Bildschirmbaugruppe durch die Halterungen und ziehen Sie anschließend die Bildschirmscharnierschrauben fest, um die Bildschirmbaugruppe zu befestigen. 3. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. 4.
Einsetzen der Bildschirmblende 1. Richten Sie die Bildschirmblende aus und drücken Sie sie fest, um sie an der Bildschirmbaugruppe zu befestigen. 2. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. h. 3. Bildschirmbaugruppe Systemplatine Tastatur Speichermodul Festplattenlaufwerk Abdeckung Optisches Laufwerk Akku Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen der Kamera 1.
a. Entfernen Sie die das Klebeband, mit dem das Kamerakabel befestigt ist [1]. b. Trennen Sie das Kamerakabel von der Kamera [2]. c. Entfernen Sie die Kamera aus der Bildschirmbaugruppe [3]. Einbauen der Kamera 1. Bringen Sie die Kamera an der Bildschirmbaugruppe an. 2. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. h. i. 3.
a. Entfernen Sie die Schrauben, mit denen die Bildschirmscharniere an der Bildschirmbaugruppe befestigt sind [1]. b. Entfernen Sie die Bildschirmscharniere [2]. Einbauen der Bildschirmsscharniere 1. Ziehen Sie die Schrauben fest, mit denen die Bildschirmscharniere an der Bildschirmbaugruppe befestigt werden. 2. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. h. i. 3.
g. h. i. j. 3. Systemplatine Bildschirmbaugruppe Bildschirmblende Bildschirmscharniere Führen Sie folgende Schritte wie in der Abbildung gezeigt durch: a. Entfernen Sie die Schrauben, mit denen der Bildschirm an der Bildschirmbaugruppe befestigt ist [1]. b. Heben Sie den Bildschirm an, um auf die Kabel darunter zuzugreifen [2]. 4. Führen Sie folgende Schritte wie in der Abbildung gezeigt durch: a. Entfernen Sie das Klebeband, mit dem das eDP-Kabel am Computer befestigt ist [1]. b.
Einsetzen des Bildschirms 1. Verbinden Sie das Bildschirmkabel mit dem Bildschirm. 2. Befestigen Sie das Bildschirmkabel mit dem Klebeband. 3. Setzen Sie den Bildschirm auf die Bildschirmbaugruppe. 4. Ziehen Sie die Schrauben fest, um den Bildschirm an der Bildschirmbaugruppe zu befestigen. 5. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. h. i. j. 6.
System-Setup 3 Über das System-Setup können Sie die Verwaltung der Computerhardware und die Festlegung der BIOSLevel-Optionen verwalten.
Tabelle 1. Navigationstasten Tasten Navigation Pfeil nach oben Zurück zum vorherigen Feld Pfeil nach unten Weiter zum nächsten Feld Ermöglicht die Eingabe eines Wertes im ausgewählten Feld (falls zutreffend) oder das Verfolgen des Links in dem Feld. Öffnet oder schließt gegebenenfalls eine Dropdown-Liste. Weiter zum nächsten Fokusbereich.
Option Beschreibung Controller, Video-BIOS-Version, Videospeicher, Bedienfeldtyp, Systemeigene Auflösung, Audio-Controller, Wi-Fi-Gerät, Bluetooth-Gerät). Battery Information Zeigt den Akkustatus und den mit dem Computer verbundenen Netzteiltyp an. Boot Sequence Boot Sequence Erlaubt es Ihnen festzulegen, in welcher Reihenfolge der Computer nach einem Betriebssystem sucht. Die Optionen sind: • • Windows Boot Manager UEFI Standardmäßig sind alle Optionen ausgewählt.
Option Beschreibung SMART Reporting Dieses Feld steuert, ob Festplattenfehler für integrierte Laufwerke während des Systemstarts gemeldet werden. Diese Technologie ist Teil der SMART-Spezifikation (Self Monitoring Analysis and Reporting Technology - System zur Selbstüberwachung, Analyse und Statusmeldung). Diese Option ist standardmäßig deaktiviert. • USB Configuration Enable SMART Reporting (SMART-Berichte aktivieren) Mit diesem Feld wird der integrierte USB-Controller konfiguriert.
Option Beschreibung Bildschirmhelligkeit je nach der Energiequelle (On Battery [Akkubetrieb] und On AC [Betrieb am Stromnetz]). ANMERKUNG: Sie sollte nur für Windows 7 und neuere Version von Windows oder des Ubuntu-Betriebssystems aktiviert werden. Tabelle 5. Sicherheit Option Beschreibung Admin Password Ermöglicht das Einrichten, Ändern oder Löschen des Administratorkennworts (Admin).
Option Beschreibung Password Bypass Ermöglicht das Aktivieren oder Deaktivieren der Berechtigungen, die Kennwörter des Systems und der internen Festplatte zu umgehen, wenn diese festgelegt sind. Die Optionen sind: • • Deaktiviert Reboot bypass (Neustart umgehen) Die Standardeinstellung ist: Disabled (Deaktiviert) Password Change Ermöglicht das Aktivieren der Deaktivierungsberechtigung bezüglich der System- und Festplattenkennwörter, wenn das Admin-Kennwort festgelegt ist.
Option Beschreibung Wenn der benutzerdefinierte Modus aktiviert ist, werden die entsprechenden Optionen für PK, KEK, db und dbx angezeigt. Die Optionen sind: • • • • • • Save to File (In Datei speichern) – Speichert den Schlüssel in einer vom Benutzer ausgewählten Datei. Replace from File (Aus Datei ersetzen) – Ersetzt den aktuellen Schlüssel durch einen Schlüssel aus einer vom Benutzer ausgewählten Datei.
Option Beschreibung Standardeinstellung: Die Option ist aktiviert. Hyper-Thread Control Ermöglicht das Aktivieren oder Deaktivieren von HyperThreading im Prozessor. • • Deaktiviert Aktiviert Standardeinstellung: Die Option ist aktiviert. Tabelle 8. Stromverwaltung Option Beschreibung AC Behavior Ermöglicht die Aktivierung oder Deaktivierung des automatischen Einschaltens des Computers, wenn das Netzteil angeschlossen ist.
Option Beschreibung Primary Battery Charge Configuration Ermöglicht die Auswahl des Lademodus für den Akku. Die Optionen sind: • • • • Adaptive (Adaptiv) Standard – Lädt den Akku vollständig mit Standardrate auf.
Option Beschreibung • Enable Intel Virtualization Technology (IntelVirtualisierungstechnologie aktivieren) (Standardeinstellung) Aktiviert oder deaktiviert die Nutzung der von der Intel®Virtualisierungstechnologie für direktes E/A bereitgestellten zusätzlichen Hardwarefunktionen durch den VMM (Virtual Machine Monitor). VT for Direct I/O Enable VT for Direct I/O (VT für direktes E/A aktivieren) – standardmäßig aktiviert. Tabelle 11.
Aktualisieren des BIOS Es wird empfohlen, das BIOS zu aktualisieren (System-Setup), wenn die Systemplatine ausgetauscht wurde oder ein Update verfügbar ist. Sollten Sie ein Notebook verwenden, stellen Sie sicher, dass der Akku vollständig geladen und der Computer an das Stromnetz angeschlossen ist. 1. Starten Sie den Computer neu. 2. Rufen Sie die Website dell.com/support auf. 3.
Kennworttyp Beschreibung Setup password (Setup-Kennwort) Dies ist das Kennwort, das Sie für den Zugriff auf und Änderungen an den BIOSEinstellungen des Computers eingeben müssen. VORSICHT: Die Kennwortfunktionen bieten einen gewissen Schutz für die auf dem System gespeicherten Daten. VORSICHT: Wenn Ihr Computer nicht gesperrt und unbeaufsichtigt ist, kann jede Person auf die auf dem System gespeicherten Daten zugreifen.
Löschen oder Ändern eines vorhandenen System- und/oder SetupKennworts Stellen Sie sicher, dass der Password Status Kennwortstatus) (im System-Setup) auf Unlocked (Nicht gesperrt) gesetzt ist, bevorSie versuchen, das vorhandende System- und/oder -Kennwort zu löschen oder zu ändern. Sie können ein vorhandenes System-oder Setup-Kennwort nicht löschen oder ändern, wenn der Password Status (Kennwortstatus) auf Locked (Gesperrt) gesetzt ist.
Diagnose 4 Enhanced Pre-boot System Assessment (ePSA, Erweiterte Systemtests vor Hochfahren des Computers) Die ePSA-Diagnose (auch als Systemdiagnose bezeichnet) führt eine komplette Prüfung der Hardware durch. Die ePSA-Diagnose ist in das BIOS integriert und wird intern vom BIOS gestartet. Die integrierte Systemdiagnose bietet verschiedene Optionen für bestimmte Geräte oder Gerätegruppen.
5 Technische Daten Technische Daten ANMERKUNG: Die angebotenen Konfigurationen können je nach Region variieren. Um weitere (Start-Symbol) Informationen zur Konfiguration des Computers zu erhalten, klicken Sie auf Start → Hilfe und Support und wählen Sie dann die Option zur Anzeige der Informationen über Ihren Computer aus. Tabelle 14. Systeminformationen Funktion Beschreibung Chipsatz In Prozessor integriert DRAM-Busbreite 64 Bit Flash-EPROM 16 MB Tabelle 15.
Tabelle 17. Audio Funktion Beschreibung Typ Zweikanal-High-Definition-Audio Controller Realtek ALC3234 mit Waves Maxx Audio Stereo-Konvertierung 24-Bit (Analog-zu-Digital und Digital-zu-Analog) Schnittstelle Intel HDA-Bus Lautsprecher 2x2W Lautstärkeregler Programm-Menü und Tasten zur Mediensteuerung Tabelle 18.
Funktion Beschreibung USB: • • Ein USB 3.0-Anschluss Zwei USB 2.0-Anschlüsse ANMERKUNG: Der erweiterterte USB 3.0-Anschluss unterstützt auch das Microsoft-KernelDebuggen. Die Ports sind in der dem Computer beiliegenden Dokumentation gekennzeichnet. Medienkartenlesegerät Ein SD-Steckplatz Tabelle 22.
Tabelle 24. Touchpad Funktion Beschreibung Aktiver Bereich: X-Achse 105,00 mm (4,13 Zoll) Y-Achse 80,00 mm (3,14 Zoll) Tabelle 25.
Funktion Beschreibung Betrieb 0 °C bis 40 °C (32 °F bis 104 °F) Nicht in Betrieb -40 °C bis 70 °C (-40 °F bis 158 °F) Tabelle 27. Abmessungen und Gewicht Funktion Beschreibung Höhe: 23,75 mm (0,93 Zoll) Breite: 380,00 mm (14,96 Zoll) Tiefe: 260,40 mm (10,25 Zoll) Gewicht: 2,24 kg (4,94 lb) Tabelle 28. Umgebungsbedingungen Funktion Beschreibung Temperatur: Betrieb 0 °C bis 35 °C (32 °F bis 95 °F) Bei Lagerung -40 °C bis 65 °C (-40 °F bis 149 °F) Relative Luftfeuchtigkeit (max.
Kontaktaufnahme mit Dell 6 Kontaktaufnahme mit Dell ANMERKUNG: Wenn Sie nicht über eine aktive Internetverbindung verfügen, können Sie Kontaktinformationen auch auf Ihrer Auftragsbestätigung, dem Lieferschein, der Rechnung oder im Dell-Produktkatalog finden. Dell stellt verschiedene onlinebasierte und telefonische Support- und Serviceoptionen bereit. Da die Verfügbarkeit dieser Optionen je nach Land und Produkt variiert, stehen einige Services in Ihrer Region möglicherweise nicht zur Verfügung.