Dell Vostro 3580 دليل الخدمة النموذج الرقابيP75F : النوع الرقابيP75F010 :
الملاحظات والتنبيهات والتحذيرات ملاحظة تشير كلمة "ملاحظة" إلى معلومات هامة تساعدك على تحقيق أقصى استفادة من المنتج الخاص بك. تنبيه تشير كلمة "تنبيه" إلى احتمال حدوث تلف بالأجهزة أو فقد للبيانات وت ُعلمك بكيفية تجنب المشكلة. تحذير تشير كلمة "تحذير" إلى احتمال حدوث تلف بالممتلكات أو وقوع إصابة شخصية أو الوفاة. حقوق النشر © 2019لشركة Dell Inc.أو الشركات التابعة لها .جميع الحقوق محفوظة .علامة Dellو EMCوالعلامات التجارية الأخرى هي علامات تجارية لشركة Dell Inc.
جدول المحتويات 1العمل على الكمبيوتر الخاص بك6 .................................................................................................................... إرشادات الأمان6 ............................................................................................................................................................................. إيقاف تشغيل جهاز الكمبيوتر الخاص بك — 6 ........................................................................................................
محرك الأقراص الثابتة33 .................................................................................................................................................................. إزالة مجموعة محرك الأقراص الثابتة33 ........................................................................................................................................ تركيب مجموعة محرك الأقراص الثابتة35 ...........................................................................................................
تركيب كابل الشاشة81 ................................................................................................................................................................. غطاء الشاشة الخلفي ومجموعة الهوائي82 ............................................................................................................................................ إزالة الغطاء الخلفي للشاشة82 .................................................................................................................
1 العمل على الكمبيوتر الخاص بك إرشادات الأمان المتطلبات استعن بإرشادات السلامة التالية لحماية جهاز الكمبيوتر الخاص بك من أي تلف محتمل وضمان سلامتك الشخصية .ما لم يتم الإشارة إلى غير ذلك ،فإن كل إجراء متضمن في هذا المستند يفترض وجود الظروف التالية: • • قيامك بقراءة معلومات الأمان الواردة مع الكمبيوتر. يمكن استبدال أحد المكونات أو ،في حالة شرائه بصورة منفصلة ،تركيبه من خلال اتباع إجراءات الإزالة بترتيب عكسي.
قبل العمل داخل الكمبيوتر عن المهمة لتجنب إتلاف جهاز الكمبيوتر الخاص بك ،قم بإجراء الخطوات التالية قبل التعامل مع الأجزاء الداخلية لجهاز الكمبيوتر. الخطوات .1تأكد من اتباعك تعليمات السلامة. .2تأكد أن سطح العمل مسطح ونظيف لوقاية غطاء جهاز الكمبيوتر من التعرض للخدوش. .3قم بإيقاف تشغيل جهاز الكمبيوتر الخاص بك. .4افصل كل كابلات الشبكة عن جهاز الكمبيوتر. تنبيه لفصل كابل الشبكة ،قم أولاً بفصل الكابل عن جهاز الكمبيوتر ،ثم افصله عن الجهاز المتصل بالشبكة. .
2 التكنولوجيا والمكونات ملاحظة تنطبق التعليمات الواردة في هذا القسم على أجهزة الكمبيوتر المزودة بنظام التشغيل .Windows 10تم تثبيت نظام التشغيل Windows 10في المصنع بهذا الكمبيوتر. الموضوعات: • • • • DDR4 HDMI 1.
الحافة المنحنية تتميز وحدات DDR4بحافة منحنية للمساعدة في الإدخال وتقليل الضغط على لوحة الدائرة المطبوعة ) (PCBأثناء تركيب الذاكرة. شكل .3الحافة المنحنية أخطاء الذاكرة تعرض أخطاء الذاكرة على النظام رمز فشل ON-FLASH-FLASHأو ON-FLASH-ONالجديد .إذا فشلت جميع وحدات الذاكرة ،فلن يتم تشغيل شاشة .
ميزات USB تم طرح الناقل التسلسلى العالمى ،أو ،USBفي عام .1996وقد قام بتبسيط الاتصال بشكل كبير بين أجهزة الكمبيوتر المضيفة والأجهزة الطرفية مثل أجهزة الماوس ولوحات المفاتيح ومحركات الأقراص الخارجية والطابعات. دعنا نلق نظرة سريعة على تطور USBبالإشارة إلى الجدول أدناه. جدول .1تطور USB النوع معدل نقل البيانات الفئة سنة الإصدار USB 2.0 480ميجابت/ث سرعة عالية 2000 منفذ USB 3.0/USB 3.
نظرا لتزايد المتطلبات المتعلقة بعمليات نقل البيانات اليوم من خلال محتوى الفيديو فائق الدقة وأجهزة التخزين بسعة التيرابايت والكاميرات الرقمية بدقة فائقة بوحدات الميجابكسل ،إلخ ،.قد ً لا تكون USB 2.0سريعة بما فيه الكفاية .وعلاوة ً على ذلك ،لا يمكن أن تأتي وصلة USB 2.0بسعة معالجة قصوى نظرية تبلغ 480ميجابت/ث تقريبًا ،مما يتيح نقل البيانات بمعدل 320ميجابت/ث ) 40ميجابت/ث( تقريبًا — الحد الأقصى الفعلي .وبالمثل ،لن تحقق وصلات منفذ USB 3.0/USB 3.1من الجيل الأول مطلقًا 4.
• برنامج تشغيل Intel Rapid Storage Technologyمن الإصدار 15.9.1.1018أو إصدار أعلى جدول .2مواصفات ذاكرة Intel Optane الميزة المواصفات الواجهة PCIe 3x2 NVMe 1.1 الموصل فتحة بطاقة (M.2 (2230/2280 التهيئات المدعومة • • • السعة 16جيجابايت معالج Intel Core i3/i5/i7من الجيل السابع أو الأعلى نظام التشغيل 64 Windows 10بت الإصدار 1607أو الأعلى برنامج تشغيل Intel Rapid Storage Technologyمن الإصدار 15.9.1.
3 إزالة المكونات وتركيبها الأدوات الموصى باستخدامها قد تتطلب الإجراءات الواردة في هذه الوثيقة توفر الأدوات التالية: • • • مفك فيليبس 0# مفك فيليبس 1# مخطاط بلاستيكي ملاحظة مفك المسامير اللولبية 0#للمسامير اللولبية 0-1ومفك المسامير اللولبية للمسامير اللولبية .4-2 قائمة المسامير اللولبية يوفر الجدول قائمة المسامير اللولبية التي يتم استخدامها لتثبيت المكونات المختلفة. جدول .
المكون نوع المسمار اللولبي الكمية المشتت الحراري M2x3 3 اللوحة الفرعية VGA M2x3 2 لوحة الإدخال/الإخراج M2x4 1 لوحة اللمس M2x2 4 دعامة لوحة اللمس M2x2 2 لوحة زر التشغيل M2x2برأس كبيرة 1 لوحة النظام M2x4 1 زر التشغيل مع قارئ بصمات الأصابع )اختياري( M2x2برأس كبيرة 1 منفذ مهايئ التيار M2x3 1 لوحة الشاشة M2x2 4 المفصلات M2.5x2.
تركيب البطاقة الرقمية الآمنة الصغيرة الخطوات .1قم بإزاحة البطاقة الرقمية الآمنة الصغيرة إلى داخل الفتحة حتى تستقر في مكانها. .2اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك.
مجموعة محرك الأقراص الضوئية إزالة مجموعة محرك الأقراص الضوئية المتطلبات .1اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. .2إزالة بطاقة ذاكرة SD الخطوات .1قم بإزالة المسمار اللولبي ) (M2x4الأحادي الذي يثبت محرك الأقراص الضوئية في النظام ].[1 .2قم بإزاحة محرك الأقراص الضوئية خارج جهاز الكمبيوتر ].
.3قم بإزالة المسمارين اللولبيين ) (M2x3اللذين يثبتان دعامة محرك الأقراص الضوئية بمحرك الأقراص الضوئية ].[1 .4قم بإزالة حامل محرك الأقراص الضوئية من محرك الأقراص الضوئية ].[2 تركيب مجموعة محرك الأقراص الضوئية الخطوات .1قم بمحاذاة حامل محرك الأقراص الضوئية مع فتحات المسامير اللولبيةالموجودة في وحدة محرك الأقراص الضوئية ].[1 .2قم بإزالة المسمارين اللولبيين ) (M2x3اللذين يثبتان دعامة محرك الأقراص الضوئية بمحرك الأقراص الضوئية ].
.3أدخل محرك الأقراص الضوئية في الفتحة حتى يستقر في مكانه محدثًا صوت طقطقة[1]. .4أعد وضع المسمار اللولبي ) (M2x4الأحادي الذي يثبت محرك الأقراص الضوئية في النظام ].[2 الخطوات التالية .1أعد وضع بطاقة ذاكرة SD .2اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك.
غطاء القاعدة إزالة غطاء القاعدة المتطلبات .1اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. .2إزالة بطاقة ذاكرة SD .3إزالة مجموعة محرك الأقراص الضوئية الخطوات .1قم بفك مسامير التثبيت الثلاثة ].[1 .2قم بإزالة المسمار اللولبي ) (M2.5x7الفردي ،والمسمارين اللولبيين ) ،(M2x2والمسامير اللولبية ) (M2.5x7التي تثبت غطاء القاعدة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[4 ،3 ،2 .
تركيب غطاء القاعدة الخطوات .1ضع غطاء القاعدة على مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .
.3أحكم ربط مسامير التثبيت الثلاثة وأعد وضع المسمار اللولبي ) (M2x4الذي يثبت غطاء القاعدة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 ،1 .4قم بإزالة المسمارين اللولبيين ) (M2x2والمسامير اللولبية ) (M2.5x7الستة التى تثبت غطاء القاعدة في مجموعة مسند راحة اليد ولوحة المفاتيح ].
الخطوات التالية .1أعد وضع مجموعة محرك الأقراص الضوئية .2أعد وضع بطاقة ذاكرة SD .3اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. وحدة )وحدات( الذاكرة إزالة وحدة الذاكرة المتطلبات .1 .2 .3 .4 .5 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD إزالة مجموعة محرك الأقراص الضوئية قم بإزالة غطاء القاعدة افصل كابل البطارية عن الموصل الموجود في لوحة النظام. الخطوات .
ملاحظة إذا لم تسمع صوت استقرار وحدة الذاكرة في موضعها ،فقم بإزالتها وإعادة تركيبها. الخطوات التالية .1 .2 .3 .4 .5 قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. بطاقة WLAN إزالة بطاقة WLAN المتطلبات .1 .2 .3 .4 .
تركيب بطاقة WLAN عن المهمة تنبيه لتجنب تلف بطاقة الشبكة اللاسلكية لا تضع أي كبلات أسفلها. الخطوات .1قم بإدخال بطاقة WLANفي الموصل الموجود في لوحة النظام ].[1 .2قم بتوصيل كابلات WLANبالموصلات الموجودة على بطاقة .[WLAN [2 .3ضع دعامة بطاقة WLANلتثبيت كبلات WLANفي بطاقة .[WLAN [3 .4أعد وضع المسمار اللولبي الفردي ) (M2x3لتثبيت رف WLANببطاقة .
الخطوات التالية .1 .2 .3 .4 .5 قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. محرك الأقرص المزود بذاكرة مصنوعة من مكونات صلبة/الذاكرة بتقنية Optaneمن Intel إزالة محرك أقراص مزود بذاكرة مصنوعة من مكونات صلبة من نوع M.2 2230 المتطلبات .1 .2 .3 .4 .
سا على عقب. .4أدر اللوحة الحرارية رأ ً .5قم بإزالة المسمار اللولبي ) (M2x2الذي يثبت محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة باللوحة الحرارية ].[1 .6ارفع محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة بعيدا عن اللوحة الحرارية ].[2 تركيب محرك أقراص مزود بذاكرة مصنوعة من مكونات صلبة من نوع M.2 2230 الخطوات .1ضع محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة داخل فتحة اللوحة الحرارية ].[1 .
.3قم بمحاذاة السن الموجود في محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة مع اللسان الموجود في فتحة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة. .4قم بإزاحة لسان محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة وأدخله في فتحة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة ].[1 .5احكم ربط مسمار التثبيت الذى يثبت اللوحة الحرارية بمجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .6أعد وضع المسمار اللولبي ) (M2x3الذي يثبت اللوحة الحرارية في مجموعة مسند راحة اليد ولوحة المفاتيح ].
إزالة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة أو ذاكرة Optane من - Intelاختياري المتطلبات .1 .2 .3 .4 .5 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD إزالة مجموعة محرك الأقراص الضوئية قم بإزالة غطاء القاعدة افصل كابل البطارية عن الموصل الموجود في لوحة النظام. الخطوات .1قم بفك مسمار التثبيت الذي يثبت اللولحة الحرارية بمجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .
الخطوات التالية .1 .2 .3 .4 .5 قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. البطارية الخلوية المصغرة إزالة البطارية الخلوية المصغرة المتطلبات .1 .2 .3 .4 .5 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك.
تركيب البطارية الخلوية المصغرة الخطوات .1مع جعل الجانب الموجب متجها الى أعلى ،أدخل البطارية الخلوية المصغرة داخل مقبس البطارية الموجود على لوحة الإدخال/الإخراج ].[1 .2اضغط على البطارية حتى تستقر في مكانها ].
الخطوات التالية .1 .2 .3 .4 .5 قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. البطارية التدابير الوقائية لبطارية ليثيوم أيون تنبيه • توخِ الحذر عند التعامل مع بطاريات الليثيوم.أيون. • احرص على تفريغ شحنة البطارية قدر الإمكان قبل إزالتها من النظام .
إخراج البطارية المتطلبات .1 .2 .3 .4 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD إزالة مجموعة محرك الأقراص الضوئية. قم بإزالة غطاء القاعدة. الخطوات .1افصل كبل البطارية عن لوحة النظام ].[1 .2قم بإزالة المسامير اللولبية الأربعة ) (M2x3التي تثبت البطارية في مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .3ارفع البطارية خارج مجموعة مسند راحة اليد ولوحة المفاتيح ].[3 تركيب البطارية الخطوات .
الخطوات التالية .1 .2 .3 .4 أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. محرك الأقراص الثابتة إزالة مجموعة محرك الأقراص الثابتة المتطلبات .1 .2 .3 .4 .5 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD إزالة مجموعة محرك الأقراص الضوئية قم بإزالة غطاء القاعدة قم بإزالة البطارية الخطوات .
.4افصل الموزع من محرك الأقراص الثابتة. .5قم بإزالة المسامير اللولبية الأربعة ) (M3x3التي تثبت رف محرك الأقراص الثابتة في محرك الأقراص الثابتة ].[1 .6قم برفع رف محرك الأقراص الثابتة خارج محرك الأقراص الثابتة ].
تركيب مجموعة محرك الأقراص الثابتة الخطوات .1قم بمحاذاة فتحات المسامير اللولبية الموجودة في حامل محرك الأقراص الثابتة مع فتحات المسامير اللولبية الموجودة في محرك الأقراص الثابتة ].[1 .2أعد وضع المسامير اللولبية الأربعة ) (M3x3التي تثبت رف محرك الأقراص الثابتة في محرك الأقراص الثابتة ].[2 .3قم بتوصيل الموزع بمحرك الأقراص الثابتة.
.4قم بمحاذاة فتحات المسامير اللولبية الموجودة في مجموعة محرك الأقراص الثابتة مع فتحات المسامير اللولبية الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .5أعد وضع المسامير اللولبية الأربعة ) (M2x3التي تثبت مجموعة محرك الأقراص الثابتة بمجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .6قم بتوصيل كابل محرك الأقراص الثابتة بلوحة النظام وأغلق المزلاج لتثبيت الكابل ].[3 الخطوات التالية .1 .2 .3 .4 .5 36 أعد وضع البطارية أعد وضع غطاء القاعدة.
مروحة النظام إزالة مروحة النظام المتطلبات .1 .2 .3 .4 .5 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD إزالة مجموعة محرك الأقراص الضوئية قم بإزالة غطاء القاعدة افصل كابل البطارية عن الموصل الموجود في لوحة النظام. الخطوات .1افصل كابل محرك الأقراص الضوئية ) (ODDوكابل الشاشة وكابل المروحة عن لوحة النظام ].[3 ،2 ،1 .2قم بإلغاء توجيه كبل الشاشة من أدلة التوجيه الموجود على المروحة ].
.3قم بإزالة المسامير اللولبية الثلاثة ) (M2.5x5المثبتة للمروحة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .4ارفع المروحة عن مجموعة مسند راحة اليد ولوحة المفاتيح ].
تركيب مروحة النظام الخطوات .1قم بمحاذاة فتحات المسامير اللولبية الموجودة في المروحة مع فتحات المسامير اللولبية الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .2أعد وضع المسامير اللولبية الثلاثة ) (M2.5x5المثبتة للمروحة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .3قم بتوجيه كبل الشاشة خلال أدلة التوجيه الموجودة على المروحة ].
.4قم بتوصيل كابل محرك الأقراص الضوئية ) (ODDوكابل الشاشة وكابل المروحة بلوحة النظام ].[3 ،2 ،1 الخطوات التالية .1أعد وضع البطارية .2أعد وضع غطاء القاعدة. .
.4أعد وضع بطاقة ذاكرة SD .5اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. المشتت الحراري إزالة غرفة التبريد - المتطلبات .1 .2 .3 .4 .5 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD إزالة مجموعة محرك الأقراص الضوئية قم بإزالة غطاء القاعدة. افصل كبل البطارية عن الموصل الموجود في لوحة النظام. الخطوات .1قم بفك المسامير اللولبية المثبتة لغرفة التبريد بلوحة النظام ].
.2أعد وضع المسامير اللولبية ) (M2x3الثلاثة التي تثبت محرك غرفة التبريد بلوحة النظام ].[2 .3بترتيب تسلسلي) ،كما هو موضح على غرفة التبريد( ،اربط المسامير المثبتة لغرفة التبريد في لوحة النظام ].[3 الخطوات التالية .1 .2 .3 .4 .5 قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك.
.13قم بإزالة لوحة الإدخال والإخراج .14إزالة مجموعة الشاشة .15إزالة لوحة النظام الخطوات افصل كبل VGAوقم بازالته من مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 تركيب كابل VGA الخطوات قم بتوصيل كبل VGAوثبته على مجموعة مسند راحة اليد ولوحة المفاتيح ].
الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 .13 .14 .15 أعد وضع لوحة النظام أعد تركيب مجموعة الشاشة أعد وضع لوحة الإدخال والإخراج أعد وضع غرفة التبريد أعد وضع مروحة النظام أعد وضع مجموعة محرك الأقراص الثابتة أعد وضع البطارية الخلوية المصغرة أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع الذاكرة قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة.
الخطوات .1افصل كبل مكبر الصوت من لوحة النظام ].[1 .2قم بإلغاء توجيه كبل مكبر الصوت من أدلة التوجيه وقم بإزالتها من مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .3ارفع مكبرات الصوت ،مع الكابل الخاص بها ،خارج مجموعة مسند راحة اليد ولوحة المفاتيح ].[3 تركيب مكبرات الصوت عن المهمة ملاحظة إذا كان قد تم دفع حلقات التثبيت المطاطية للخارج عند إزالة مكبرات الصوت ،فادفعها للداخل مرة أخرى قبل إعادة تركيب مكبرات الصوت. الخطوات .
الخطوات التالية .1 .2 .3 .4 .5 .6 أعد وضع محرك SSD أعد وضع البطارية أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. لوحة الإدخال/الإخراج )(IO إزالة لوحة الإدخال والإخراج المتطلبات .1 .2 .3 .4 .5 .6 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD إزالة مجموعة محرك الأقراص الضوئية.
.3قم بإزالة المسمار اللولبي ) (M2x4المثبتين للوحة الإدخال/الإخراج بمجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .4ارفع لوحة الإدخال/الإخراج ،جنبًا إلى جنب مع الكابل ،خارج مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 ملاحظة عند فصل كابل لوحة الإدخال/الإخراج عن لوحة النظام ،يحدث خطأ في .RTCيحدث هذا الخطأ عندما تتم إزالة /RTCالبطارية الخلوية المصغرة/أو لوحة الإدخال/الإخراج أو لوحة النظام.
تركيب لوحة الإدخال والإخراج الخطوات .1باستخدام دعامات المحاذاة ،ضع لوحة الإدخال/الإخراج على مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .2أعد وضع المسمار اللولبي ) (M2x4المثبتين للوحة الإدخال/الإخراج بمجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .3قم بتوصيل كابل VGAبلوحة ) I/Oالإدخال/الإخراج( ].[1 .4قم بتوصيل كابل لوحة وحدة الإدخال/الإخراج ) (I/Oبلوحة النظام ،وأغلق المزلاج لثبيت الكابل ].
الخطوات التالية .1 .2 .3 .4 .5 .6 أعد وضع مجموعة محرك الأقراص الثابتة أعد وضع البطارية. أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. لوحة اللمس إزالة مجموعة لوحة اللمس المتطلبات .1 .2 .3 .4 .5 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD إزالة مجموعة محرك الأقراص الضوئية.
.3قم بإزالة المسمارين اللولبيين ) (M2x2المثبتين لحامل لوحة اللمس في مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .4ارفع حامل لوحة اللمس خارج مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .5قم بإزالة وضع المسامير اللولبية الأربعة ) (M2x2التي تثبت لوحة اللمس بمجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .6ارفع لوحة اللمس بعيدًا عن مجموعة مسند راحة اليد ولوحة المفاتيح ].
تركيب مجموعة لوحة اللمس عن المهمة ملاحظة قم بالتأكد من محاذاة لوحة اللمس للأدلة المتاحة على مجموعة مسند راحة اليد ولوحة المفاتيح ،وأن الفجوة الموجودة على جانبي لوحة اللمس متساوية. الخطوات .1ضع لوحة اللمس في الفتحة الموجودة بمجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .2أعد وضع المسامير اللولبية الأربعة ) (M2x2التي تثبت لوحة اللمس بمجموعة مسند راحة اليد ولوحة المفاتيح ].
.3ضع رف لوحة اللمس في الفتحة الموجودة بمجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .4أعد وضع المسمارين اللولبيين ) (M2x2المثبتين لحامل لوحة اللمس في مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .5ثبت الشريط اللاصق الذي يثبت لوحة اللمس بمجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .6قم بإزاحة كابل المحرك وكابل لوحة اللمس إلى داخل الموصل الموجود في لوحة النظام وأغلق المزلاج لتثبيت الكابلات ].
الخطوات التالية .1 .2 .3 .4 .5 أعد وضع البطارية أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. مجموعة الشاشة إزالة مجموعة الشاشة المتطلبات .1 .2 .3 .4 .5 .6 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك.
.4قم بإزالة المسامير اللولبية الخمسة ) (M2.5x5المثبتة للمفصلتين اليمنى واليسرى بلوحة النظام ومجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .5ارفع مجموعة مسند راحة اليد ولوحة المفاتيح بزاوية ].[2 .6ارفع المفصلات .
.7بعد أداء جميع الخطوات السابقة ،تتبقى مجموعة الشاشة.
تركيب مجموعة الشاشة عن المهمة ملاحظة تاكد من فتح المفصلات إلى الحد الاقصى قبل إعادة وضع مجموعة الشاشة على مجموعة مسند راحة اليد ولوحة المفاتيح. الخطوات .1قم بمحاذاة مجموعة مسند راحة اليد ولوحة المفاتيح تحت المفصلات على مجموعة الشاشة ].[1 .2قم بتثبيت مجموعة مسند راحة اليد ولوحة المفاتيح في مجموعة الشاشة ].[2 .3اضغط على المفصلات للأسفل على لوحة النظام ،ومجموعة مسند راحة اليد ولوحة المفاتيح ].[3 .4أعد وضع المسامير اللولبية الخمسة ) (M2.
.5قم بتوجيه كبل الشاشة عبر أدلة التوجيه الموجودة على مجموعة مسند راحة اليد ولوحة المفاتيح].[1 .6ثبت كبلات الهوائي بلوحة النظام ].[2 .7قم بتوصيل كبل الشاشة وكبل محرك الأقراص الضوئية بالموصل الموجود على لوحة النظام ].
الخطوات التالية .1 .2 .3 .4 .5 .6 أعد وضع بطاقة WLAN قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. لوحة زر التشغيل إزالة لوحة زر التشغيل المتطلبات .1 .2 .3 .4 .5 .6 .7 .8 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك.
تركيب لوحة زر التشغيل الخطوات .1ضع لوحة زر الطاقة في الفتحة الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .2أعد وضع المسمار اللولبي ) (M2x2الذي يثبت لوحة زر الطاقة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .3قم بتركيب الشريط الموصل بلوحة زر الطاقة ].[3 .4قم بتوصيل كابل زر الطاقة بلوحة النظام وأغلق المزلاج لتثبيت الكابل ].[4 الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .
.5 .6 .7 .8 .9 .10 قم بإزالة الذاكرة قم بإزالة WLAN قم بإزالة محرك أقراص SSD قم بإزالة مروحة النظام قم بإزالة المشتت الحراري قم بإزالة مجموعة الشاشة الخطوات .1افصل كبل منفذ مهايئ التيار ،وكبل محرك الأقراص الضوئية ،وكبل مكبر الصوت عن لوحة النظام ].[3 ،2 ،1 .2قم بإزالة المسمار اللولبي ) (M2x2الذي يثبت موصل محرك الأقراص الضوئية بلوحة النظام ].[1 .3ارفع موصل محرك الأقراص الضوئية ].
.4افصل الكابلات التالية من لوحة النظام: (a (b (c (d (e (f كبل لوحة زر التشغيل ].[1 كبل لوحة بصمات الأصابع ].[2 كبل لوحة .[I/O [3 كبل محرك الأقراص الثابتة ].[4 كبل لوحة اللمس ].[5 كبل لوحة المفاتيح ].
.5قم بإزالة المسمار اللولبي ) (M2x4الذي يثبت لوحة النظام في مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .6اقلب لوحة النظام بعيدًا عن مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .7افصل كبل لوحة VGAالفرعية عن لوحة النظام ].[1 .8ارفع لوحة النظام بعيدًا عن مجموعة مسند راحة اليد ولوحة المفاتيح ].
تركيب لوحة النظام الخطوات .1ضع لوحة النظام في مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .2قم بتوصيل كبل لوحة VGAالفرعية بلوحة النظام ].[2 .3اقلب لوحة النظام في مجموعة مسند راحة اليد ولوحة المفاتيح ].[3 .4قم بمحاذاة فتحة المسمار اللولبي الموجودة في لوحة النظام مع فتحة المسمار اللولبي الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح. .5أعد وضع المسمار اللولبي ) (M2x4الذي يثبت لوحة النظام في مجموعة مسند راحة اليد ولوحة المفاتيح ].
.6ضع موصل محرك الأقراص الضوئية وأعد وضع المسمار اللولبي ) (M2x2الذي يثبته بلوحة النظام ].[2 ،1 .7قم بتوصيل الكبلات التالية بلوحة النظام: (aكبل لوحة زر التشغيل ].[1 (bكبل لوحة بصمات الأصابع ].[2 (cكبل لوحة .
(dكبل محرك الأقراص الثابتة ].[4 (eكبل لوحة اللمس ].[5 (fكبل لوحة المفاتيح ].[6 .8قم بتوصيل كبل منفذ مهايئ التيار ،وكبل محرك الأقراص الضوئية ،وكبل مكبر الصوت بلوحة النظام ].
الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 أعد تركيب مجموعة الشاشة أعد وضع المشتت الحراري أعد وضع مروحة النظام أعد وضع محرك أقراص SSD أعد وضع WLAN أعد وضع الذاكرة أعد وضع البطارية أعد وضع غطاء القاعدة أعد وضع بطاقة ذاكرة SD اتبع الإجراء الوارد في بعد العمل داخل جهاز الكمبيوتر الخاص بك زر التشغيل إزالة زر التشغيل مع قارئ بصمات الأصابع المتطلبات .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .
تركيب زر التشغيل مع قارئ بصمات الأصابع الخطوات .1ثبت كبل قارئ بصمات الأصابع في مجموعة مسند راحة اليد ولوحة المفاتيح. .2باستخدام دعامات المحاذاة ،قم بمحاذاة زر التشغيل ووضعه بمجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .3أعد وضع المسمار اللولبي ) (M2x2الذي يثبت زر الطاقة في مجموعة مسند راحة اليد ولوحة المفاتيح ].
الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 أعد وضع لوحة النظام أعد وضع زر الطاقة أعد تركيب مجموعة الشاشة أعد وضع غرفة التبريد أعد وضع مروحة النظام أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع البطارية أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. منفذ مهايئ التيار إزالة منفذ مهايئ التيار المتطلبات .
الخطوات .1افصل كابل مهايئ التيار وقم بتوجيه من لوحة النظام ].[2 ،1 .2قم بإزالة المسمار اللولبي ) (M2x3الذي يثبت منفذ مهايئ التيار في مجموعة مسند راحة اليد ولوحة المفاتيح ].[3 .3ارفع منفذ مهايئ التيار مع الكابل الخاص به بعيدًا عن مجموعة مسند راحة اليد ولوحة المفاتيح ].[4 تركيب منفذ مهايئ التيار الخطوات .1ضع منفذ مهايئ التيار في الفتحة الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .
الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .8 .9 أعد وضع زر الطاقة أعد تركيب مجموعة الشاشة أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع البطارية أعد وضع غطاء القاعدة أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. إطار الشاشة إزالة إطار الشاشة المتطلبات .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .
الخطوات .1ارفع الجانب الداخلى العلوي لإطار الشاشة ].[1 .2تابع رفع الحافتين الداخليتين اليسرى واليمنى من حواف إطار الشاشة ].[2 .3ارفع الجزء السفلي من الحافة الداخلية من إطار الشاشة ،ثم ارفع الإطار خارج مجموعة الشاشة ].[3 تركيب إطار الشاشة الخطوات قم بمحاذاة إطار الشاشة مع الغطاء الخلفي للشاشة ومجموعة الهوائي وقم بتثبيت إطار الشاشة في مكانه بعناية ].
الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 أعد تركيب مجموعة الشاشة أعد وضع مجموعة محرك الأقراص الثابتة أعد وضع مروحة النظام أعد وضع غرفة التبريد أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع الذاكرة قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك.
.10إزالة غرفة التبريد .11إزالة مجموعة الشاشة .12إزالة إطار الشاشة الخطوات .1باستخدام مخطاط بلاستيكي ،ارفع الكاميرا خارج مجموعة الغطاء الخلفي للشاشة والهوائي برفق ].[1 .2افصل كابل الكاميرا من وحدة الكاميرا ].[2 .3ارفع وحدة الكاميرا من مجموعة الغطاء الخلفي للشاشة والهوائي ].[3 تركيب الكاميرا الخطوات .1قم بتوصيل كابل الكاميرا بوحدة الكاميرا ].[1 .2باستخدام عمود المحاذاة ،ثبت الكاميرا على مجموعة الغطاء الخلفي للشاشة والهوائي ].[2 .
الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 أعد وضع إطار الشاشة أعد تركيب مجموعة الشاشة أعد وضع مجموعة محرك الأقراص الثابتة أعد وضع مروحة النظام أعد وضع غرفة التبريد أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع البطارية أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. لوحة الشاشة إزالة لوحة الشاشة المتطلبات .
.7 .8 .9 .10 .11 .12 .13 إزالة محرك SSD إزالة مجموعة محرك الأقراص الثابتة إزالة مروحة النظام إزالة غرفة التبريد إزالة مجموعة الشاشة إزالة إطار الشاشة إزالة الكاميرا الخطوات .1أزل المسامير اللولبية الأربعة ) (M2x2المثبتة للوحة الشاشة في مجموعة الغطاء الخلفي للشاشة والهوائي ].[1 .2ارفع لوحة الشاشة واقلبها ].[2 .3انزع الشريط الذي يثبت كابل الشاشة بالجزء الخلفي للوحة الشاشة ].[1 .
تركيب لوحة الشاشة الخطوات .1ضع لوحة الشاشة على سطح مست ٍو ونظيف ].[1 .2قم بتوصيل كابل الشاشة بالموصل الموجود في الجزء الخلفي من لوحة الشاشة وقم بإغلاق المزلاج لتثبيت الكابل ].[2 .3قم بلصق الشريط الذي يثبت كابل الشاشة بالجزء الخلفي للوحة الشاشة ].[3 سا على عقب وضعها على مجموعة الغطاء الخلفي للشاشة والهوائي ].[4 .
.5قم بمحاذاة فتحات المسامير اللولبية الموجودة في لوحة الشاشة مع فتحات المسامير اللولبية الموجودة في مجموعة الغطاء الخلفي للشاشة والهوائي . .6قم بإعادة وضع المسامير اللولبية الأربعة ) (M2x2المثبتة للوحة الشاشة في مجموعة الغطاء الخلفي للشاشة والهوائي ].
الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 .13 أعد وضع الكاميرا أعد وضع إطار الشاشة أعد تركيب مجموعة الشاشة أعد وضع مجموعة محرك الأقراص الثابتة أعد وضع مروحة النظام أعد وضع غرفة التبريد أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع البطارية. أعد وضع غطاء القاعدة. أعد وضع مجموعة محرك الأقراص الضوئية أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك.
تركيب مفصلات الشاشة الخطوات .1قم بمحاذاة فتحات المسامير اللولبية الموجودة على المفصلات والدعامات مع فتحات المسامير اللولبية الموجودة على مجموعة الغطاء الخلفي للشاشة والهوائي ].[1 .2أعد وضع المسامير اللولبية الثمانية ) (M2.5x2.5والمسمارين ) (M2x2اللولبيين المثبتين للمفصلات بمجموعة الغطاء الخلفي للشاشة والهوائي ].
الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 .13 .14 أعد وضع لوحة الشاشة أعد وضع الكاميرا أعد وضع إطار الشاشة أعد تركيب مجموعة الشاشة أعد وضع مجموعة محرك الأقراص الثابتة أعد وضع مروحة النظام أعد وضع غرفة التبريد أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع البطارية أعد وضع غطاء القاعدة.
.5 .6 .7 .8 .9 .10 .11 .12 .13 .14 قم بإزالة البطارية إزالة بطاقة WLAN إزالة محرك SSD إزالة مجموعة محرك الأقراص الثابتة قم بإزالة مروحة النظام قم بإزالة غرفة التبريد إزالة مجموعة الشاشة إزالة إطار الشاشة إزالة لوحة الشاشة إزالة مفصلات الشاشة الخطوات .1افصل كابل الكاميرا في مجموعة الغطاء الخلفي للشاشة والهوائي ].[1 .2انزع اللاصق الذي يثبت كبل الكاميرا ].[2 .
الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 .13 .14 أعد وضع مفصلات الشاشة أعد وضع لوحة الشاشة أعد وضع إطار الشاشة أعد تركيب مجموعة الشاشة أعد وضع مجموعة محرك الأقراص الثابتة أعد وضع مروحة النظام أعد وضع غرفة التبريد أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع البطارية أعد وضع غطاء القاعدة.
.6 .7 .8 .9 .10 .11 .12 .13 .14 .15 .16 إزالة بطاقة WLAN إزالة محرك SSD إزالة مجموعة محرك الأقراص الثابتة إزالة مروحة النظام إزالة غرفة التبريد إزالة مجموعة الشاشة إزالة إطار الشاشة إزالة الكاميرا إزالة لوحة الشاشة إزالة مفصلات الشاشة إزالة كابل الشاشة عن المهمة بعد تنفيذ جميع الخطوات أعلاه ،يتبقى لك الغطاء الخلفي للشاشة.
تركيب الغطاء الخلفي للشاشة عن المهمة ضع الغطاء الخلفي للشاشة على سطح نظيف ومست ٍو. . الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 .13 .14 .15 .
مجموعة مسند راحة اليد ولوحة المفاتيح إزالة مجموعة مسند راحة اليد ولوحة المفاتيح المتطلبات .1اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. .2إزالة بطاقة ذاكرة SD .3إزالة مجموعة محرك الأقراص الضوئية .4قم بإزالة غطاء القاعدة. .5أخرج البطارية .6إزالة الذاكرة .7إزالة بطاقة WLAN .8إزالة محرك SSD .9بإزالة مكبرات الصوت. .10إزالة البطارية الخلوية المصغرة. .11إزالة مجموعة محرك الأقراص الثابتة .12إزالة مروحة النظام .
86 إزالة المكونات وتركيبها
4 استشكاف الأخطاء وإصلاحها تشخيصات التقييم المحسن للنظام قبل التمهيد )(ePSA عن المهمة تقوم تشخيصات ) ePSAالمعروفة أيضًا بتشخيصات النظام( بفحص كامل لجهازك .يتم تضمين ePSAبنظام الإدخال والإخراج الأساسي ) (BIOSويتم تشغيلها داخليًا بواسطة نظام الإدخال والإخراج الأساسي ) .
جدول .4رموز مؤشر LED رموز مصابيح التشخيص وصف المشكلة 2,1 عطل المعالج 2,2 لوحة النظام :عطل في BIOSأو ) ROMذاكرة القراءة فقط( 2,3 لم يتم اكتشاف ذاكرة أو ذاكرة ) RAMذاكرة وصول عشوائي( 2,4 عطل في الذاكرة أو ذاكرة ) RAMذاكرة الوصول العشوائي( 2,5 تم تثبيت ذاكرة غير صالحة 2,6 خطأ في لوحة النظام أو مجموعة الشرائح 2,7 عطل في الشاشة 2.8 عطل في قضيب تيار .
.2قم بالانتقال إلى .www.dell.com/support .3انقر على ) Product supportدعم المنتج( ،وأدخل علامة الخدمة الخاصة بجهاز الكمبيوتر لديك ،ثم انقر على ) Submitإرسال(. ملاحظة إذا لم يكن لديك رمز الخدمة ،فاستخدم ميزة الكشف التلقائي أو استعرض يدويًا طراز جهاز الكمبيوتر الخاص بك. .4قم بالنقر على ) Drivers & downloadsبرامج التشغيل والتنزيلات( < ) Find it myselfالعثور عليها بنفسي(. .5حدد نظام التشغيل المثبت على جهاز الكمبيوتر الخاص بك. .6مرر الصفحة لأسفل وقم بتوسيع .
5 الحصول على المساعدة الموضوعات: • الاتصال بشركة Dell الاتصال بشركة Dell المتطلبات ملاحظة إذا لم يكن لديك اتصال نشط بالإنترنت ،فيمكنك العثور على معلومات الاتصال على فاتورة الشراء الخاصة بك أو إيصال الشحن أو الفاتورة أو كتيب منتج .Dell عن المهمة توفر Dellالعديد من خيارات الدعم والخدمة القائمة على الهاتف والإنترنت .يختلف التوفر حسب البلد والمنتج ،وقد لا تتوفر بعض الخدمات في منطقتك .