Dell Vostro 3580 Servisni priručnik Model sa regulacijom: P75F Tip sa regulacijom: P75F010
Napomene, mere opreza i upozorenja NAPOMENA Oznaka NAPOMENA ukazuje na važne informacije koje vam pomažu da bolje koristite proizvod. OPREZ Oznaka OPREZ ukazuje na potencijalno oštećenje hardvera ili gubitak podataka i objašnjava vam kako da izbegnete problem. UPOZORENJE UPOZORENJE ukazuje na opasnost od oštećenja opreme, telesnih povreda ili smrti. © 2019. Dell Inc. ili podružnice. Sva prava zadržana. Dell, EMC, i drugi žigovi su žigovi Dell Inc. ili njegovih podružnica.
Sadržaj 1 Rad na računaru........................................................................................................................... 6 Bezbednosna uputstva......................................................................................................................................................... 6 Isključivanje računara — Windows 10.................................................................................................................................
Čvrsti disk............................................................................................................................................................................. 33 Uklanjanje sklopa hard diska......................................................................................................................................... 33 Montiranje sklopa hard diska...............................................................................................................................
Montiranje kabla ekrana.................................................................................................................................................81 Sklop zadnjeg poklopca ekrana i antene...........................................................................................................................82 Uklanjanje zadnjeg poklopca ekrana............................................................................................................................
1 Rad na računaru Bezbednosna uputstva Preduslovi Koristite sledeće bezbednosne smernice kako biste zaštitili računar od mogućih oštećenja i osigurali ličnu bezbednost. Osim ako je drugačije navedeno, svaka procedura obuhvaćena ovim dokumentom pretpostavlja da postoje slijedeći uslovi: • • Pročitali ste bezbednosne informacije koje ste dobili uz računar. Komponenta se može zameniti ili, ako je kupljena odvojeno, montirati izvođenjem procedure uklanjanja u obrnutom redosledu.
NAPOMENA Uvjerite se da su računar i svi priključeni uređaji isključeni. Ako se računar i priključeni uređaji ne isključe automatski prilikom isključivanja operativnog sistema, pritisnite i držite dugme za uključivanje/isključivanje oko 6 sekundi da biste ih isključili. Pre rada u unutrašnjosti računara Informacije o ovom zadatku Da biste izbegli oštećenje računara, prođite kroz sledeće korake pre nego što počnete sa radom u unutrašnjosti računara. Koraci 1. Obavezno poštujte Bezbednosna uputstva. 2.
2 Tehnologija i komponente NAPOMENA Uputstva iz ovog odeljka odnose se na računare isporučene sa operativnim sistemom Windows 10. Windows 10 je fabrički instaliran operativni sistem na ovom računaru. Teme: • • • • DDR4 HDMI 1.4 Funkcije USB-a Intel Optane memorija DDR4 DDR4 (četvrta generacija memorije sa dvostrukom brzinom prenosa podataka) brži je naslednik DDR2 i DDR3 tehnologija i pruža do 512 GB kapaciteta, u poređenju sa 128 GB po DIMM-u za DDR3.
Zakrivljena ivica DDR4 moduli se odlikuju zakrivljenom ivicom, što pomaže prilikom ubacivanja modula u ležište i smanjuje pritisak na štampanu pločicu tokom instalacije memorije. Slika 3. Zakrivljena ivica Greške u vezi sa memorijom Greške u vezi sa memorijom sistema prikazuju nove kodove otkazivanja UKLJUČENO-BLJESAK-BLJESAK ili UKLJUČENO-BLJESAKUKLJUČENO. Ako memorija potpuno otkaže, LCD se ne uključuje.
• • • Audio HDMI podržava više audio formata, od standardnog stereo do višekanalnog prostornog zvuka HDMI kombinuje video i višekanalni audio u jednom kablu i na taj način eliminiše troškove, složenost i zbrku više kablova koji se trenutno koriste u A/V sistemima HDMI podržava komunikaciju između video izvora (kao što je DVD plejer) i DTV-a i na taj način omogućava novu funkcionalnost Funkcije USB-a Univerzalna serijska magistrala ili USB je predstavljena 1996. godine.
Sa današnjim rastućim zahtevima koji se postavljaju za prenos podataka sa video sadržajem visoke definicije, uređajima za skladištenje veličine terabajta, digitalnim kamerama sa velikim brojem piksela, itd, USB 2.0 možda nije dovoljno brz. Osim toga, nijedna USB 2.0 veza se nikada neće približiti teorijskoj maksimalnoj propusnosti od 480 Mb/s, zbog čega je prenos podataka pri oko 320 Mb/s (40 MB/s) maksimalna brzina u stvarnosti. Slično tome, USB 3.0/USB 3.1 Gen 1 veze nikada neće postići 4,8 Gb/s.
• Intel Core i3/i5/i7 procesor 7. generacije ili noviji • Windows 10 64-bitna verzija 1607 ili novija • Upravljački program za Intel Rapid Storage Technology verzije 15.9.1.1018 ili noviji Tabela 2. Specifikacije Intel Optane memorije Karakteristika Specifikacije Interfejs PCIe 3x2 NVMe 1.1 Konektor Slot za M.2 karticu (2230/2280) Podržane konfiguracije • • • Kapacitet 16 GB Intel Core i3/i5/i7 procesor 7.
3 Uklanjanje i instaliranje komponenti Preporučeni alati Za procedure u ovom dokumentu mogu se zahtevati sledeći alati: • • • Phillips odvrtač br. 0 Phillips odvrtač br. 1 Plastična olovka NAPOMENA Odvijač br. 0 je za zavrtnje 0–1, a odvijač br. 1 za zavrtnje 2–4. Lista zavrtanja U sledećoj tabeli je navedena lista zavrtanja koji se koriste za učvršćivanje različitih komponenti. Tabela 3.
Кomponentа Tip zavrtnja Količina Rashladni element M2x3 3 VGA priključna ploča M2x3 2 U/I ploča M2x4 1 Tabla osetljiva na dodir M2x2 4 Nosač table osetljive na dodir M2x2 2 Ploča dugmeta za napajanje M2x2 sa velikom glavom 1 Matična ploča M2x4 Dugme za napajanje sa čitačem otiska prsta (opcionalno) M2x2 sa velikom glavom 1 Port adaptera za napajanje M2x3 1 Ploča ekrana M2x2 4 Zglobovi M2,5x2,5 8 M2x2 2 M2x3 1 Nosač bežične kartice 1 Micro Secure Digital kartica Uklanja
Postavljanje Micro Secure Digital kartice Koraci 1. Gurnite Micro Secure Digital karticu u pripadajući slot tako da legne u ležište. 2. Sledite procedure u odeljku Posle rada u unutrašnjosti računara.
Sklop optičke disk jedinice Uklanjanje sklopa optičke disk jedinice Preduslovi 1. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara 2. Uklonite SD memorijsku karticu Koraci 1. Uklonite zavrtanj (M2x4) koji učvršćuje optičku disk jedinicu za sistem [1]. 2. Povucite optičku disk jedinicu izvan računara [2].
3. Skinite dva zavrtnja (M2x3) koji učvršćuju konzolu optičkog diska za optičku disk jedinicu [1]. 4. Uklonite nosač optičke disk jedinice sa optičke disk jedinice. [2]. Postavljanje sklopa optičke disk jedinice Koraci 1. Poravnajte nosač optičke disk jedinice sa otvorima na optičkoj disk jedinici. [1]. 2. Ponovo postavite dva zavrtnja (M2x3) koji učvršćuju konzolu optičkog diska za optičku disk jedinicu.
3. Umetnite optičku disk jedinicu u slot tako da "klikne" u ležište. [1]. 4. Ponovo postavite zavrtanj (M2x4) koji učvršćuje optičku disk jedinicu za sistem [2]. Sledeći koraci 1. Ponovo postavite SD memorijsku karticu 2.
Poklopac osnove Uklanjanje poklopca osnove Preduslovi 1. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara 2. Uklonite SD memorijsku karticu 3. Uklonite sklop optičkog diska Koraci 1. Olabavite tri neispadajuća zavrtnja [1]. 2. Uklonite jedan (M2x4) zavrtanj, dva (M2x2) zavrtnja i šest zavrtnja (M2,5x7) koji učvršćuju poklopac osnove za sklop oslonca za dlan i tastature [2, 3, 4]. 3. Podignite poklopac osnove sa gornjeg desnog ugla [1] i nastavite da otvarate desnu stranu poklopca osnove [2].
Montiranje poklopca osnove Koraci 1. Pod uglom postavite poklopac osnove sa sklopa oslonca za dlanove i tastature [1]. 2. Pritisnite desnu stranu poklopca osnove dok se ne smesti u ležište [2, 3].
3. Zategnite tri neispadajuća zavrtnja i zamenite jedan zavrtanj (M2x4) koji učvršćuju poklopac osnove za sklop oslonca za dlan i tastature [1, 2]. 4. Uklonite dva zavrtnja (M2x2) i šest zavrtanja (M2.5x7) koji učvršćuju poklopac osnove za sklop oslonca za dlan i tastature [3, 4].
Sledeći koraci 1. Ponovo postavite sklop optičkog diska 2. Ponovo postavite SD memorijsku karticu 3. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara Memorijski moduli Uklanjanje memorijskog modula Preduslovi 1. 2. 3. 4. 5. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara Uklonite SD memorijsku karticu Uklonite sklop optičkog diska Uklonite poklopac osnove Izvucite kabl baterije iz konektora na matičnoj ploči. Koraci 1.
NAPOMENA Ako ne čujete klik, uklonite memorijski modul i ponovo ga instalirajte. Sledeći koraci 1. 2. 3. 4. 5. Povežite kabl baterije sa konektorom na matičnoj ploči. Ponovo postavite poklopac osnove Ponovo postavite sklop optičkog diska Ponovo postavite SD memorijsku karticu Sledite proceduru u odeljku Posle rada u unutrašnjosti računara WLAN kartica Uklanjanje WLAN kartice Preduslovi 1. 2. 3. 4. 5.
Montiranje WLAN kartice Informacije o ovom zadatku OPREZ Da biste sprečili oštećenje bežične kartice, ne postavljajte kablove ispod nje. Koraci 1. Ubacite WLAN karticu u konektor na matičnoj ploči [1]. 2. Povežite WLAN kablove sa konektorima na WLAN kartici [2]. 3. Postavite nosač WLAN kartice da biste povezali WLAN kablove sa WLAN karticom [3]. 4. Postavite jedan (M2x3) zavrtanj da biste učvrstili WLAN nosač za WLAN karticu [4].
Sledeći koraci 1. 2. 3. 4. 5. Povežite kabl baterije sa konektorom na matičnoj ploči. Ponovo postavite poklopac osnove Ponovo postavite sklop optičkog diska Ponovo postavite SD memorijsku karticu Sledite proceduru u odeljku Posle rada u unutrašnjosti računara Poluprovodnički disk/Intel Optane memorija Uklanjanje M.2 2230 poluprovodničkog diska Preduslovi 1. 2. 3. 4. 5.
4. Preokrenite termalnu ploču. 5. Uklonite zavrtanj (M2x2) koji učvršćuje poluprovodnički disk za termalnu ploču [1]. 6. Podignite poluprovodnički disk sa termalne ploče [2]. Postavljanje M.2 2230 poluprovodničkog diska Koraci 1. Postavite poluprovodnički disk u slot na termalnoj ploči [1]. 2. Postavite zavrtanj (M2x2) koji učvršćuje poluprovodnički disk za termalnu ploču [2].
3. Poravnajte zarez na poluprovodničkom disku sa držačem na priključku za poluprovodnički disk. 4. Gurnite i ubacite jezičak poluprovodničkog diska u slot za poluprovodnički disk [1]. 5. Zategnite neispadajući zavrtanj koji učvršćuje termalnu ploču za sklop oslonca za dlan i tastature [2]. 6. Postavite jedan (M2x3) zavrtanj koji učvršćuje termalnu ploču za sklop oslonca za dlan i tastature [3]. Sledeći koraci 1. 2. 3. 4. 5. Povežite kabl baterije sa konektorom na matičnoj ploči.
Uklanjanje M.2 2280 poluprovodničkog diska ili Intel Optane memorije – opcionalno Preduslovi 1. 2. 3. 4. 5. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara Uklonite SD memorijsku karticu Uklonite sklop optičkog diska Uklonite poklopac osnove Izvucite kabl baterije iz konektora na matičnoj ploči. Koraci 1. Olabavite neispadajući zavrtanj koji učvršćuje termalnu ploču za sklop oslonca za dlan i tastature [1]. 2.
Sledeći koraci 1. 2. 3. 4. 5. Povežite kabl baterije sa konektorom na matičnoj ploči. Ponovo postavite poklopac osnove Ponovo postavite sklop optičkog diska Ponovo postavite SD memorijsku karticu Sledite proceduru u odeljku Posle rada u unutrašnjosti računara Dugmasta baterija Uklanjanje dugmaste baterije Preduslovi 1. 2. 3. 4. 5.
Montiranje dugmaste baterije Koraci 1. Gurnite dugmastu bateriju u priključak za bateriju na U/I ploči tako da pozitivna strana baterije bude okrenuta prema gore [1]. 2. Pritisnite bateriju tako da klikne u ležište [2].
Sledeći koraci 1. 2. 3. 4. 5. Povežite kabl baterije sa konektorom na matičnoj ploči. Ponovo postavite poklopac osnove Ponovo postavite sklop optičkog diska Ponovo postavite SD memorijsku karticu Sledite proceduru u odeljku Posle rada u unutrašnjosti računara Baterija Bezbednosne mere za litijum-jonsku bateriju OPREZ • Budite oprezni pri rukovanju litijum-jonskih baterija. • Ispraznite bateriju što je više moguće pre nego što je izvadite iz sistema.
Uklanjanje baterije Preduslovi 1. 2. 3. 4. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara Uklonite SD memorijsku karticu Uklonite sklop optičke disk jedinice Uklonite poklopac osnove Koraci 1. Odvojite kabl baterije sa matične ploče [1]. 2. Uklonite četiri (M2x3) zavrtnja koji učvršćuju bateriju za sklop oslonca za dlan i tastature [2]. 3. Podignite bateriju sa sklopa oslonca za dlan i tastature [3]. Montiranje baterije Koraci 1.
Sledeći koraci 1. 2. 3. 4. Postavite poklopac osnove Ponovo postavite sklop optičke disk jedinice Ponovo postavite SD memorijsku karticu Sledite proceduru u odeljku Posle rada u unutrašnjosti računara Čvrsti disk Uklanjanje sklopa hard diska Preduslovi 1. 2. 3. 4. 5. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara Uklonite SD memorijsku karticu Uklonite sklop optičkog diska Uklonite poklopac osnove Uklonite bateriju Koraci 1.
4. Odspojite prenosnik sa čvrstog diska. 5. Uklonite četiri zavrtnja (M3x3) koji učvršćuju konzolu hard diska za hard disk [1]. 6. Podignite konzolu hard diska sa hard diska [2].
Montiranje sklopa hard diska Koraci 1. Poravnajte otvore za zavrtnje na nosaču hard diska sa otvorima za zavrtnje na hard disku [1]. 2. Ponovo postavite četiri zavrtnja (M3x3) koji učvršćuju konzolu hard diska za hard disk [2]. 3. Povežite prenosnik sa čvrstim diskom.
4. Poravnajte otvore za zavrtnje na sklopu hard diska sa otvorima za zavrtnje na sklopu oslonca za dlan i tastature [1]. 5. Ponovo postavite četiri zavrtnja (M2x3) koji učvršćuju sklop hard diska za sklop oslonca za dlan i tastature [2]. 6. Povežite kabl hard diska na matičnu ploču i zatvorite rezu da biste fiksirali kabl [3]. Sledeći koraci 1. 2. 3. 4. 5.
Ventilator sistema Uklanjanje ventilatora sistema Preduslovi 1. 2. 3. 4. 5. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara Uklonite SD memorijsku karticu Uklonite sklop optičkog diska Uklonite poklopac osnove Izvucite kabl baterije iz konektora na matičnoj ploči. Koraci 1. Izvucite ODD kabl, kabl ekrana i kabl ventilatora sa matične ploče [1, 2, 3]. 2. Izvucite kabl ekrana iz vođica za usmeravanje na ventilatoru [1].
3. Uklonite tri (M2,5x5) zavrtnja kojima je ventilator pričvršćen na sklop oslonca za dlan i tastature [1]. 4. Podignite ventilator sa sklopa oslonca za dlan i tastature [2].
Montiranje ventilatora sistema Koraci 1. Poravnajte otvore za zavrtnje na ventilatoru sa otvorima za zavrtnje na sklopu oslonca za dlan i tastature [1]. 2. Postavite tri (M2,5x5) zavrtnja kojima je ventilator pričvršćen na sklop oslonca za dlan i tastature [2]. 3. Provucite kabl ekrana kroz vođice za usmeravanje na ventilatoru [1].
4. Povežite ODD kabl, kabl ekrana i kabl ventilatora na matičnu ploču [3,2,1]. Sledeći koraci 1. Ponovo postavite bateriju 2. Ponovo postavite poklopac osnove 3.
4. Ponovo postavite SD memorijsku karticu 5. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara Rashladni element Uklanjanje rashladnog elementa Preduslovi 1. 2. 3. 4. 5. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara Uklonite SD memorijsku karticu Uklonite sklop optičke disk jedinice Uklonite poklopac osnove Izvucite kabl baterije iz konektora na matičnoj ploči. Koraci 1. Olabavite četiri neispadajuća zavrtnja koji učvršćuju rashladni element za matičnu ploču [1].
Postavljanje rashladnog elementa Koraci 1. Postavite rashladni element na matičnu ploču i poravnajte otvore za zavrtnje na rashladnom elementu sa otvorima za zavrtnje na matičnoj ploči [1]. 2. Postavite tri zavrtnja (M2x3) koji učvršćuju rashladni element za matičnu ploču [2]. 3. Prema određenom redosledu (naznačenom na rashladnom elementu) pritegnite četiri neispadajuća zavrtnja kojima je rashladni element pričvršćen za matičnu ploču [3]. Sledeći koraci 1. 2. 3. 4. 5.
6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Uklonite memoriju Uklonite WLAN Uklonite SSD Uklonite dugmastu bateriju Uklonite sklop hard diska Uklonite ventilator sistema Uklonite rashladni element Uklonite U/I ploču Uklonite sklop ekrana Uklonite matičnu ploču Koraci Izvucite VGA kabl i uklonite ga sa sklopa oslonca za dlan i tastature [1]. Postavljanje VGA kabla Koraci Povežite VGA kabl i pričvrstite ga za sklop oslonca za dlan i tastature [1].
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Ponovo postavite matičnu ploču Ponovo postavite sklop ekrana Ponovo postavite U/I ploču Ponovo postavite rashladni element Ponovo postavite ventilator sistema Ponovo postavite sklop hard diska Ponovo postavite dugmastu bateriju Ponovo postavite SSD Ponovo postavite WLAN Ponovo postavite memoriju Povežite kabl baterije sa konektorom na matičnoj ploči.
Koraci 1. Izvucite kabl zvučnika sa matične ploče [1]. 2. Izvadite i uklonite kabl zvučnika iz vođica za usmeravanje na sklopu oslonca za dlan i tastature [2]. 3. Podignite zvučnike zajedno sa odgovarajućim kablom sa sklopa oslonca za dlan i tastature [3]. Montiranje zvučnika Informacije o ovom zadatku NAPOMENA Ako ste izvukli gumene uvodnice kada ste uklanjali zvučnik, vratite ih nazad pre nego što postavite zvučnik. Koraci 1.
Sledeći koraci 1. 2. 3. 4. 5. 6. Ponovo postavite SSD Ponovo postavite bateriju Ponovo postavite poklopac osnove Ponovo postavite sklop optičkog diska Ponovo postavite SD memorijsku karticu Sledite proceduru u odeljku Posle rada u unutrašnjosti računara U/I ploča Uklanjanje U/I ploče Preduslovi 1. 2. 3. 4. 5. 6.
3. Uklonite jedan (M2x4) zavrtnja kojim(a) je U/I ploča pričvršćena za sklop oslonca za dlan i tastature [1]. 4. Podignite U/I ploču zajedno sa kablom sa sklopa oslonca za dlan i tastature [2]. NAPOMENA Kada se kabl U/I ploče izvuče sa matične ploče, dolazi do RTC greške. Ta greška se javlja kada god se RTC/dugmasta baterija, U/I ploča ili matična ploča uklone. U tim slučajevima, nakon ponovnog sklapanja sistema, sistem vrši ciklus resetovanja RTC-a i računar se uključuje i isključuje nekoliko puta.
Poruka o grešci „Invalid Configuration“ (Nevažeća konfiguracija) prikazuje se sa uputstvom da otvorite BIOS i podesite datum i vreme. Računar počinje da funkcioniše normalno posle podešavanja datuma i vremena. Postavljanje U/I ploče Koraci 1. Pomoću stubića za poravnanje postavite U/I ploču na sklop oslonca za dlan i tastature [1]. 2. Postavite jedan (M2x4) zavrtanj kojim(a) je U/I ploča pričvršćena za sklop oslonca za dlan i tastature [2]. 3. Povežite VGA kabl na U/I ploču [1]. 4.
Sledeći koraci 1. 2. 3. 4. 5. 6. Ponovo postavite sklop hard diska Ponovo postavite bateriju Ponovo postavite poklopac osnove Ponovo postavite sklop optičke disk jedinice Ponovo postavite SD memorijsku karticu Sledite proceduru u odeljku Posle rada u unutrašnjosti računara Tabla osetljiva na dodir Uklanjanje sklopa table osetljive na dodir Preduslovi 1. 2. 3. 4. 5.
3. Uklonite dva (M2x2) zavrtnja koji učvršćuju nosač table osetljive na dodir za sklop oslonca za dlan i tastature [1]. 4. Podignite nosač table osetljive na dodir sa sklopa oslonca za dlan i tastature [2]. 5. Uklonite četiri (M2x2) zavrtnja koji učvršćuju tablu osetljivu na dodir za sklop oslonca za dlan i tastature [1]. 6. Podignite tablu osetljivu na dodir sa sklopa oslonca za dlan i tastature [2].
Montiranje sklopa table osetljive na dodir Informacije o ovom zadatku NAPOMENA Proverite da li je tabla osetljiva na dodir poravnata sa vođicama na sklopu oslonca za dlanove i tastature i da li je razmak na obe strane table osetljive na dodir jednak. Koraci 1. Postavite tablu osetljivu na dodir u slot na sklopu oslonca za dlan i tastature [1]. 2. Ponovo postavite četiri (M2x2) zavrtnja koji učvršćuju tablu osetljivu na dodir za sklop oslonca za dlan i tastature [2].
3. Postavite nosač table osetljive na dodir u slot na sklopu oslonca za dlan i tastature [1]. 4. Ponovo postavite dva (M2x2) zavrtnja koji učvršćuju nosač table osetljive na dodir za sklop oslonca za dlan i tastature [2]. 5. Zalepite traku koja učvršćuje tablu osetljivu na dodir za sklop oslonca za dlan i tastature [1]. 6. Gurnite table osetljive na dodir i kabl hard diska u odgovarajući konektor na matičnoj ploči i zatvorite rezu da biste fiksirali kablove [2, 3].
Sledeći koraci 1. 2. 3. 4. 5. Ponovo postavite bateriju Ponovo postavite poklopac osnove Ponovo postavite sklop optičke disk jedinice Ponovo postavite SD memorijsku karticu Sledite proceduru u odeljku Posle rada u unutrašnjosti računara Sklop ekrana Uklanjanje sklopa ekrana Preduslovi 1. 2. 3. 4. 5. 6.
4. Uklonite pet zavrtnjeva (M2,5x5) koji učvršćuju levi i desni zglob na matičnu ploču i sklop oslonca za dlan i tastature [1]. 5. Podignite i izvadite sklop oslonca za dlan i tastature pod uglom [2]. 6. Podignite zglobove.
7. Nakon obavljanja svih gore navedenih koraka ostaje nam sklop ekrana.
Montiranje sklopa ekrana Informacije o ovom zadatku NAPOMENA Vodite računa da su zglobovi otvoreni do maksimuma pre nego što postavite sklop ekrana na sklop oslonca za dlan i tastature. Koraci 1. Poravnajte i postavite sklop oslonca za dlan i tastature ispod zglobova na sklopu ekrana [1]. 2. Postavite sklop oslonca za dlan i tastature na sklop ekrana [2]. 3. Pritisnite zglobove nadole na matičnu ploču i sklop oslonca za dlan i tastature [3]. 4.
5. Provucite kabl ekrana kroz vođice za usmeravanje na sklopu oslonca za dlan i tastature [1]. 6. Pričvrstite kablove antene za matičnu ploču [2]. 7. Povežite kabl ekrana i kabl optičke disk jedinice sa konektorom na matičnoj ploči [3, 4].
Sledeći koraci 1. 2. 3. 4. 5. 6. Ponovo postavite WLAN Povežite kabl baterije sa konektorom na matičnoj ploči. Ponovo postavite poklopac osnove Ponovo postavite sklop optičke disk jedinice Ponovo postavite SD memorijsku karticu Sledite proceduru u odeljku Posle rada u unutrašnjosti računara Ploča dugmeta za napajanje Uklanjanje ploče dugmeta za napajanje Preduslovi 1. 2. 3. 4. 5. 6. 7. 8.
Montiranje ploče dugmeta za napajanje Koraci 1. Postavite ploču dugmeta za napajanje u slot oslonca za dlan i tastature [1]. 2. Ponovo postavite jedan (M2x2) zavrtanj kojim je dugme za napajanje pričvršćeno za sklop oslonca za dlan i tastature [2]. 3. Zalepite lepljivu traku za ploču dugmeta za napajanje [3]. 4. Gurnite kabl dugmeta za napajanje u matičnu ploču i zatvorite rezu da biste fiksirali kabl [4]. Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8.
5. 6. 7. 8. 9. 10. Uklonite memoriju Uklonite WLAN Uklonite SSD Uklonite ventilator sistema Uklonite rashladni element Uklonite sklop ekrana Koraci 1. Odvojite kabl porta adaptera za napajanje, optičku disk jedinicu i kabl zvučnika sa matične ploče [1, 2, 3]. 2. Uklonite jedan (M2x2) zavrtanj koji učvršćuje konektor optičke disk jedinice za matičnu ploču [1]. 3. Podignite konektora optičke disk jedinice [2].
4. Izvucite sledeće kablove sa matične ploče: a) b) c) d) e) f) Kabl ploče dugmeta za napajanje [1] Kabl ploče čitača otisaka prstiju[2]. Kabl U/I ploče. [3]. Kabl hard diska [4]. Kabl table osetljive na dodir [5]. Kabl tastature [6].
5. Uklonite jedan (M2x4) zavrtanj koji učvršćuje matičnu ploču za sklop oslonca za dlan i tastature [1]. 6. Podignite matičnu ploču sa sklopa oslonca za dlan i tastature. [2]. 7. Isključite kabl VGA priključne ploče sa matične ploče [1]. 8. Podignite matičnu ploču sa sklopa oslonca za dlan i tastature. [2].
Montiranje matične ploče Koraci 1. Podignite matičnu ploču sa sklopa oslonca za dlan i tastature [1]. 2. Povežite kabl VGA priključne ploče sa matičnom pločom [2]. 3. Podignite matičnu ploču sa sklopa oslonca za dlan i tastature [3]. 4. Poravnajte otvor za zavrtanj na matičnoj ploči sa otvorom za zavrtanj na sklopu oslonca za dlanove i tastature. 5. Ponovo postavite jedan (M2x4) zavrtanj koji učvršćuje matičnu ploču za sklop oslonca za dlan i tastature [1].
6. Postavite konektor optičke disk jedinice i ponovo postavite jedan (M2x2) zavrtanj koji ga učvršćuje za matičnu ploču [1, 2]. 7. Povežite sledeće kablove na matičnu ploču: a) Kabl ploče dugmeta za napajanje [1] b) Kabl ploče čitača otisaka prstiju[2]. c) Kabl U/I ploče. [3].
d) Kabl hard diska [4]. e) Kabl table osetljive na dodir [5]. f) Kabl tastature [6]. 8. Povežite kabl porta adaptera za napajanje, optičku disk jedinicu i kabl zvučnika sa matičnom pločom [1, 2, 3].
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Ponovo postavite sklop ekrana Ponovo postavite rashladni element Ponovo postavite ventilator sistema. Ponovo postavite SSD Ponovo postavite WLAN Ponovo postavite memoriju Ponovo postavite bateriju Ponovo postavite poklopac osnove Zamenite SD memorijsku karticu Sledite proceduru u odeljku Posle rada u unutrašnjosti računara Dugme za napajanje Uklanjanje dugmeta za napajanje sa čitačem otiska prsta Preduslovi 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Postavljanje dugmeta za napajanje sa čitačem otiska prsta Koraci 1. Pričvrstite kabl čitača otiska prsta na sklop oslonca za dlanove i tastature. 2. Pomoću stubića za poravnanje poravnajte i postavite dugme za napajanje na sklopu oslonca za dlanove i tastature. [1]. 3. Ponovo postavite jedan (M2x2) zavrtanj kojim je dugme za napajanje pričvršćeno za sklop oslonca za dlan i tastature [2].
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Koraci 1. Izvucite i provucite kabl za napajanje sa matične ploče [1, 2]. 2. Uklonite jedan (M2x3) zavrtanj kojim je port adaptera za napajanje pričvršćen za sklop oslonca za dlan i tastature [3]. 3. Podignite port adaptera za napajanje zajedno sa kablom sa sklopa oslonca za dlan i tastature [4]. Montiranje porta adaptera za napajanje Koraci 1. Postavite port adaptera za napajanje u slot na sklopu oslonca za dlan i tastature [1]. 2.
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. Ponovo postavite ploču dugmeta za napajanje Ponovo postavite sklop ekrana Ponovo postavite SSD Ponovo postavite WLAN Ponovo postavite bateriju Ponovo postavite poklopac osnove Ponovo postavite sklop optičke disk jedinice Ponovo postavite SD memorijsku karticu Sledite proceduru u odeljku Posle rada u unutrašnjosti računara Okno ekrana Uklanjanje okvira ekrana Preduslovi 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Koraci 1. Podignite gornju unutrašnju stranu okvira ekrana [1]. 2. Nastavite sa podizanjem unutrašnje leve i desne ivice okvira ekrana [2]. 3. Podignite donju unutrašnju ivicu okvira ekrana i podignite okvir sa sklopa ekrana [3]. Montiranje okvira ekrana Koraci Poravnajte okvir ekrana sa sklopom zadnjeg poklopca ekrana i antene i pažljivo utisnite okvir ekrana u ležište [1].
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Ponovo postavite sklop ekrana Ponovo postavite sklop hard diska Ponovo postavite ventilator sistema Ponovo postavite rashladni element Ponovo postavite SSD Ponovo postavite WLAN Ponovo postavite memoriju Povežite kabl baterije sa konektorom na matičnoj ploči.
10. Uklonite rashladni element 11. Uklonite sklop ekrana 12. Uklonite okno ekrana Koraci 1. Pomoću plastične olovke pažljivo podignite kameru sa sklopa zadnjeg poklopca ekrana i antene [1]. 2. Izvadite kabl kamere iz konektora na modulu kamere [2]. 3. Podignite modul kamere sa sklopa zadnjeg poklopca ekrana i antene [3]. Montiranje kamere Koraci 1. Povežite kabl kamere na modul kamere [1]. 2. Pomoću stubića za poravnanje pričvrstite modul kamere na sklop zadnjeg poklopca ekrana i antene [2]. 3.
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
7. 8. 9. 10. 11. 12. 13. Uklonite SSD Uklonite sklop hard diska Uklonite ventilator sistema Uklonite rashladni element Uklonite sklop ekrana Uklonite okno ekrana Uklonite kameru Koraci 1. Uklonite četiri zavrtnja (M2x2) koji učvršćuju ploču ekrana za sklop zadnjeg poklopca ekrana i antene [1]. 2. Podignite i prevrnite ploču ekrana [2]. 3. Odlepite traku koja učvršćuje kabl ekrana za zadnji deo ploče ekrana [1]. 4. Podignite rezu i izvadite kabl ekrana iz konektora za kabl ploče ekrana [2]. 5.
Postavljanje ploče ekrana Koraci 1. Stavite ploču ekrana na ravnu i čistu površinu [1]. 2. Ubacite kabl ekrana u konektor na zadnjoj strani ploče ekrana i zatvorite rezu da biste učvrstili kabl [2]. 3. Zalepite traku koja učvršćuje kabl ekrana za zadnji deo ploče ekrana [3]. 4. Prevrnite ploču ekrana i postavite je na sklop zadnjeg poklopca ekrana i antene [4].
5. Poravnajte otvore za zavrtnje na ploči ekrana sa otvorima za zavrtnje na sklopu zadnjeg poklopca ekrana i antene. 6. Postavite četiri zavrtnja (M2x2) koji učvršćuju ploču ekrana za sklop zadnjeg poklopca ekrana i antene [1].
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
Montiranje zglobova ekrana Koraci 1. Poravnajte otvore za zavrtnje na zglobovima i nosačima sa otvorima za zavrtnje na sklopu zadnjeg poklopca ekrana i antene [1]. 2. Postavite osam zavrtnjeva (M2,5x2,5) i dva zavrtnja (M2x2) kojima su zglobovi pričvršćeni za sklop zadnjeg poklopca ekrana i antene [3,2].
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Uklonite bateriju Uklonite WLAN Uklonite SSD Uklonite sklop hard diska Uklonite ventilator sistema Uklonite rashladni element Uklonite sklop ekrana Uklonite okno ekrana Uklonite ploču ekrana Uklonite zglobove ekrana Koraci 1. Isključite kabl kamere na sklopu zadnjeg poklopca ekrana i antene [1]. 2. Odlepite lepljivu traku koja učvršćuje kabl kamere [2]. 3.
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Uklonite WLAN Uklonite SSD Uklonite sklop hard diska Uklonite ventilator sistema Uklonite rashladni element Uklonite sklop ekrana Uklonite okno ekrana Uklonite kameru Uklonite ploču ekrana Uklonite zglobove ekrana Uklonite kabl ekrana Informacije o ovom zadatku Nakon obavljanja svih navedenih koraka ostaje vam zadnji poklopac ekrana.
Montiranje zadnjeg poklopca ekrana Informacije o ovom zadatku Postavite zadnji poklopac ekrana na čistu i ravnu površinu. Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
Sklop oslonca za dlan i tastature Uklanjanje sklopa oslonca za dlan i tastature Preduslovi 1. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara 2. Uklonite SD memorijsku karticu 3. Uklonite sklop optičke disk jedinice 4. Uklonite poklopac osnove 5. Uklonite bateriju 6. Uklonite memoriju 7. Uklonite WLAN 8. Uklonite SSD 9. Uklonite zvučnike 10. Uklonite dugmastu bateriju 11. Uklonite sklop hard diska 12. Uklonite ventilator sistema 13. Uklonite rashladni element 14.
Uklanjanje i instaliranje komponenti
4 Rešavanje problema Poboljšana procena sistema pre pokretanja (ePSA) - dijagnostika Informacije o ovom zadatku ePSA dijagnostika (takođe se naziva dijagnostika sistema) vrši sveobuhvatnu proveru hardvera. ePSA je ugrađen u BIOS i BIOS ga pokreće interno.
Na primer, svetlo za status napajanja i baterije treperi žuto dva puta nakon čega sledi pauza, a zatim treperi belo tri puta nakon čega sledi pauza. Ovaj šablon 2,3 se nastavlja dok se računar ne isključi, što pokazuje da memorija ili RAM memorija nisu detektovane. Tabela u nastavku pokazuje različite svetlosne šablone za status napajanja i baterije, kao i povezane probleme. Tabela 4.
Pratite sledeće korake da biste obavili brzo ažuriranje BIOS-a: Koraci 1. Uključite računar. 2. Idite na www.dell.com/support. 3. Kliknite na stavku Product support (Podrška za proizvode), unesite servisnu oznaku svog računara, a zatim kliknite na Submit (Prosledi). NAPOMENA Ako nemate servisnu oznaku, koristite funkciju automatskog pronalaženja ili ručno potražite model računara. 4. Kliknite na Drivers & downloads (Upravljački programi i preuzimanja) > Find it myself (Pronađi sam). 5.
4. Uključite adapter za napajanje u računar. 5. Uključite računar.
5 Dobijanje pomoći Teme: • Kontaktiranje kompanije Dell Kontaktiranje kompanije Dell Preduslovi NAPOMENA Ako nemate aktivnu vezu sa Internetom, kontakt informacije možete pronaći na fakturi, otpremnici, računu ili katalogu Dell proizvoda. Informacije o ovom zadatku Dell nudi nekoliko opcija za onlajn i telefonsku podršku i servis. Dostupnost zavisi od zemlje i proizvoda, a neke usluge možda neće biti dostupne u vašoj oblasti.