) Dell Vostro 3590بدون محرك الأقراص الضوئية( دليل الخدمة النموذج الرقابيP75F : النوع الرقابيP75F010 : September 2020 مراجعة A02
الملاحظات والتنبيهات والتحذيرات ملاحظة :تشير كلمة "ملاحظة" إلى معلومات هامة تساعدك على تحقيق أقصى استفادة من المنتج الخاص بك. تنبيه :تشير كلمة "تنبيه" إلى احتمال حدوث تلف بالأجهزة أو فقد للبيانات وت ُعلمك بكيفية تجنب المشكلة. تحذير :تشير كلمة "تحذير" إلى احتمال حدوث تلف بالممتلكات أو وقوع إصابة شخصية أو الوفاة. حقوق الطبع والنشر © لعام 2019 - 2018محفوظة لشركة Dell Inc.أو الشركات التابعة لها .جميع الحقوق محفوظة .
جدول المحتويات فصل :1العمل على الكمبيوتر الخاص بك6 ............................................................................................................. إرشادات الأمان6 ............................................................................................................................................................................. قبل العمل داخل الكمبيوتر6 ........................................................................................................................
مكبرات الصوت35 .......................................................................................................................................................................... إزالة مكبرات الصوت35 ............................................................................................................................................................. تركيب مكبرات الصوت36 ....................................................................................................................
معلومات النظام71 ...................................................................................................................................................................... الفيديو72 ................................................................................................................................................................................. الأمان72 .........................................................................................................................
1 العمل على الكمبيوتر الخاص بك الموضوعات: • إرشادات الأمان إرشادات الأمان استعن بإرشادات السلامة التالية لحماية جهاز الكمبيوتر الخاص بك من أي تلف محتمل وضمان سلامتك الشخصية .ما لم يتم الإشارة إلى غير ذلك ،فإن كل إجراء متضمن في هذا المستند يفترض وجود الظروف التالية: ● قيامك بقراءة معلومات الأمان الواردة مع الكمبيوتر. ● يمكن استبدال أحد المكونات أو ،في حالة شرائه بصورة منفصلة ،تركيبه من خلال اتباع إجراءات الإزالة بترتيب عكسي.
التفريغ الإلكتروستاتيكي -الحماية من التفريغ الإلكتروستاتيكي يُعد التفريغ الإلكتروستاتيكى مثار اهتمام رئيسيًا عند التعامل مع المكونات الإلكترونية ،خاصة المكونات الحساسة مثل بطاقات التوسعة والمعالجات ووحدات ذاكرة DIMMولوحات الأنظمة .قد يؤدي وجود الشحنات الطفيفة جدًا إلى حدوث تلف للدائرة الكهربية بطرق قد لا تكون ملموسة ،مثل مشكلات التلامس المتقطع أو قصر العمر الافتراضي للمنتج .
الإلكتروستاتيكي لأن الجزء المحمول من الحقيبة يقع داخلها فقط .ضع الأجزاء الموجودة في يدك دائ ًما على حصيرة خاصة بالتفريغ الإلكتروستاتيكي ،أو داخل حقيبة مضادة للكهرباء الإستاتيكية. ● نقل المكونات الحساسة -عند نقل المكونات الحساسة للتفريغ الإلكتروستاتيكي مثل قطع الغيار أو الأجزاء المطلوب إعادتها إلى ،Dellيكون من الضروري وضع هذه الأجزاء في حقائب مضادة للكهرباء الإستاتيكية من أجل نقل آمن.
2 إزالة المكونات وتركيبها الموضوعات: • • • • • • • • • • • • • • • • • • • • • • • • • • • الأدوات الموصى باستخدامها قائمة المسامير اللولبية البطاقة الرقمية الآمنة غطاء القاعدة البطارية وحدة )وحدات( الذاكرة بطاقة WLAN محرك الأقرص المزود بذاكرة مصنوعة من مكونات صلبة/الذاكرة بتقنية Optaneمن Intel البطارية الخلوية المصغرة محرك الأقراص الثابتة مروحة النظام المشتت الحراري مكبرات الصوت لوحة الإدخال/الإخراج )(IO
جدول .1قائمة المسامير اللولبية المكون نوع المسمار اللولبي الكمية غطاء القاعدة M2.5x6 6 البطارية M2x3 4 لوحة الشاشة M2x2 4 مروحة النظام M2.5x5 3 مجموعة محرك الأقراص الثابتة M2x3 4 حامل محرك الأقراص الثابتة M3x3 4 غرفة التبريد -منفصلة M2x3 4 المفصلات M2.5x2.
جدول .1قائمة المسامير اللولبية )يتبع( المكون نوع المسمار اللولبي الكمية حامل البطاقة اللاسلكية M2x3 1 صورة مسمار لولبي البطاقة الرقمية الآمنة إزالة البطاقة الرقمية الآمنة .1اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. .1ادفع البطاقة الرقمية الآمنة لتحريرها من جهاز الكمبيوتر. .2قم بإزاحة البطاقة الرقمية الآمنة إلى خارج جهاز الكمبيوتر. تركيب البطاقة الرقمية الآمنة .
غطاء القاعدة إزالة غطاء القاعدة .1اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. .2إزالة بطاقة ذاكرة SD .1قم بفك مسامير التثبيت الثلاثة ].[1 .2قم بإزالة المسمار اللولبي حجم ) (M2x4والمسامير اللولبية ) (M2.5x7التى تثبت غطاء القاعدة فى مجموعة مسند راحة اليد ولوحة المفاتيح ].
اثنان .3ارفع غطاء القاعدة من الزاوية العلوية اليسرى ] [1وتابع الرفع لفتح جوانب غطاء القاعدة ].[4 ،3 ،2 تركيب غطاء القاعدة .1ضع غطاء القاعدة على مجموعة مسند راحة اليد ولوحة المفاتيح ].
.2اضغط على الحواف وجوانب غطاء القاعدة حتى تستقر فى مكانها ][4 ،3 ،2 .3أحكم ربط مسامير التثبيت الثلاثة وأعد وضع المسمار اللولبي ) (M2x4الذي يثبت غطاء القاعدة فى مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 ،1 .4أعد وضع المسامير اللولبية الستة ) (M2.5x7التي تثبت غطاء القاعدة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[3 .1أعد وضع بطاقة ذاكرة SD .2اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك.
البطارية التدابير الوقائية لبطارية ليثيوم أيون تنبيه: ● توخِ الحذر عند التعامل مع بطاريات الليثيوم.أيون. ● احرص على تفريغ شحنة البطارية قدر الإمكان قبل إزالتها من النظام .يمكن إجراء ذلك عن طريق فصل مهايئ التيار المتردد عن النظام للسماح بخروج بتصريف شحنة البطارية. ● لا تعمد إلى سحق البطارية أو إسقاطها أوتشويهها أو خرقها باستخدام أشياء خارجية. ● احرص على عدم تعريض البطارية لحرارة مرتفعة أو تفكيك علب البطارية وخلاياها. ● لا تضغط على سطح البطارية. ● لا تعمد إلى ثني البطارية.
تركيب البطارية .1قم بمحاذاة فتحات المسامير اللولبية الموجودة على البطارية مع فتحات المسامير الموجودة على مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .2أعد وضع المسامير اللولبية الأربعة ) (M2x3التي تثبت البطارية في مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .3قم بتوصيل كابل البطارية بلوحة النظام ].
.1أعد وضع غطاء القاعدة. .2أعد وضع بطاقة ذاكرة SD .3اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. وحدة )وحدات( الذاكرة إزالة وحدة الذاكرة .1 .2 .3 .4 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD قم بإزالة غطاء القاعدة. افصل كبل البطارية عن الموصل الموجود في لوحة النظام. .1ارفع المشابك التي تثبت وحدة الذاكرة حتى تبرز وحدة الذاكرة ].[1 .
تركيب وحدة الذاكرة .1قم بمحاذاة الفتحة الموجودة في وحدة الذاكرة مع اللسان الموجود في فتحة وحدة الذاكرة. .2قم بإزاحة وحدة الذاكرة بثبات إلى داخل الفتحة بزاوية ].[1 .3اضغط على وحدة الذاكرة لأسفل حتى تثبتها المشابك ].[2 ملاحظة :إذا لم تسمع صوت استقرار وحدة الذاكرة في موضعها ،فقم بإزالتها وإعادة تركيبها.
.1 .2 .3 .4 قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. بطاقة WLAN إزالة بطاقة WLAN .1 .2 .3 .4 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD قم بإزالة غطاء القاعدة. افصل كبل البطارية عن الموصل الموجود في لوحة النظام. .
تركيب بطاقة الشبكة اللاسلكية محلية النطاق )(WLAN تنبيه :لتجنب تلف بطاقة الشبكة اللاسلكية لا تضع أي كبلات أسفلها. .1قم بإدخال بطاقة WLANفي الموصل الموجود في لوحة النظام ].[1 .2قم بتوصيل كابلات WLANبالموصلات الموجودة على بطاقة .[WLAN [2 .3ضع دعامة بطاقة WLANلتثبيت كبلات WLANفي بطاقة .[WLAN [3 .4أعد وضع المسمار اللولبي الفردي ) (M2x3لتثبيت رف WLANببطاقة .
.1 .2 .3 .4 قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. محرك الأقرص المزود بذاكرة مصنوعة من مكونات صلبة/الذاكرة بتقنية Optaneمن Intel إزالة محرك أقراص مزود بذاكرة مصنوعة من مكونات صلبة من نوع M.2 2230 .1 .2 .3 .4 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك.
سا على عقب. .4أدر اللوحة الحرارية رأ ً .5قم بإزالة المسمار اللولبي ) (M2x2الذي يثبت محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة باللوحة الحرارية ].[1 .6ارفع محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة بعيدا عن اللوحة الحرارية ].[2 تركيب محرك أقراص مزود بذاكرة مصنوعة من مكونات صلبة من نوع M.2 2230 .1ضع محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة داخل فتحة اللوحة الحرارية ].[1 .
.1 .2 .3 .4 قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. إزالة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة M.2 2280أو ذاكرة Optaneمن - Intelاختياري .1 .2 .3 .4 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك.
تركيب محرك أقراص مزود بذاكرة مصنوعة من مكونات صلبة من نوع M.2 2280أو ذاكرة Intel Optaneالذاكرة -اختيارى .1قم بإزاحة لسان محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة/ذاكرة Intel Optaneوأدخله في فتحة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة/ ذاكرة .[Intel Optane [1، 2 .2احكم ربط مسمار التثبيت الذى يثبت اللوحة الحرارية بمجموعة مسند راحة اليد ولوحة المفاتيح ].[3 .
.1 .2 .3 .4 قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. البطارية الخلوية المصغرة إزالة البطارية الخلوية المصغرة .1 .2 .3 .4 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD قم بإزالة غطاء القاعدة. افصل كبل البطارية عن الموصل الموجود في لوحة النظام. .
تركيب البطارية الخلوية المصغرة .1قم بتوصيل البطارية الخلوية المصغرة كابل بلوحة الإدخال/الإخراج ].[1 .2ثبت البطارية الخلوية المصغرة على مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .1قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام.
.2أعد وضع غطاء القاعدة. .3أعد وضع بطاقة ذاكرة SD .4اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. محرك الأقراص الثابتة إزالة مجموعة محرك الأقراص الثابتة .1 .2 .3 .4 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD قم بإزالة غطاء القاعدة قم بإزالة البطارية .1ارفع المزلاج وافصل كابل محرك الأقراص الثابتة من لوحة النظام ].[1 .
.5قم بإزالة المسامير اللولبية الأربعة ) (M3x3التي تثبت رف محرك الأقراص الثابتة في محرك الأقراص الثابتة ].[1 .6قم برفع رف محرك الأقراص الثابتة خارج محرك الأقراص الثابتة ].[2 تركيب مجموعة محرك الأقراص الثابتة .1قم بمحاذاة فتحات المسامير اللولبية الموجودة في حامل محرك الأقراص الثابتة مع فتحات المسامير اللولبية الموجودة في محرك الأقراص الثابتة ].[1 .2أعد وضع المسامير اللولبية الأربعة ) (M3x3التي تثبت رف محرك الأقراص الثابتة في محرك الأقراص الثابتة ].
.3قم بتوصيل الموزع بمحرك الأقراص الثابتة. .4قم بمحاذاة فتحات المسامير اللولبية الموجودة في مجموعة محرك الأقراص الثابتة مع فتحات المسامير اللولبية الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .5أعد وضع المسامير اللولبية الأربعة ) (M2x3التي تثبت مجموعة محرك الأقراص الثابتة بمجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .6قم بتوصيل كابل محرك الأقراص الثابتة بلوحة النظام وأغلق المزلاج لتثبيت الكابل ].
.1 .2 .3 .4 أعد وضع البطارية أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. مروحة النظام إزالة مروحة النظام .1 .2 .3 .4 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD قم بإزالة غطاء القاعدة. افصل كبل البطارية عن الموصل الموجود في لوحة النظام. .1افصل وكابل الشاشة وكابل المروحة عن لوحة النظام ].
.2قم بإلغاء توجيه كبل الشاشة من أدلة التوجيه الموجود على المروحة . .3قم بإزالة المسامير اللولبية الثلاثة ) (M2.5x5المثبتة للمروحة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .4ارفع المروحة عن مجموعة مسند راحة اليد ولوحة المفاتيح ].
تركيب مروحة النظام .1قم بمحاذاة فتحات المسامير اللولبية الموجودة في المروحة مع فتحات المسامير اللولبية الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .2أعد وضع المسامير اللولبية الثلاثة ) (M2.5x5المثبتة للمروحة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .3قم بتوجيه كبل الشاشة خلال أدلة التوجيه الموجودة على المروحة ].
.4قم بتوصيل وكابل الشاشة وكابل المروحة بلوحة النظام ].[2 ،1 .1 .2 .3 .4 أعد وضع البطارية أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك.
المشتت الحراري إزالة غرفة التبريد .1 .2 .3 .4 .5 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD قم بإزالة غطاء القاعدة. أخرج البطارية إزالة مروحة النظام .1قم بفك المسامير اللولبية المثبتة لغرفة التبريد بلوحة النظام ].[1 ملاحظة :قم بفك المسامير اللولبية بترتيب الأرقام ] [4 ،3 ،2 ،1الموجودة في الشكل التوضيحي كما هو مبين على غرفة التبريد. .2ارفع غرفة التبريد خارج لوحة النظام ].[2 تركيب غرفة التبريد .
.1 .2 .3 .4 .5 قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع البطارية أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. مكبرات الصوت إزالة مكبرات الصوت .1 .2 .3 .4 .5 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD قم بإزالة غطاء القاعدة. أخرج البطارية قم بإزالة محرك أقراص SSDمن نوع .M.2 .
تركيب مكبرات الصوت ملاحظة :إذا كان قد تم دفع حلقات التثبيت المطاطية للخارج عند إزالة مكبرات الصوت ،فادفعها للداخل مرة أخرى قبل إعادة تركيب مكبرات الصوت. .1باستخدام دعامات المحاذاة وحلقات التثبيت المطاطية ،ضع مكبرات الصوت في الفتحات الموجودة على مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .2قم بتوجيه كابل مكبر الصوت عبر أدلة التوجيه الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .3قم بتوصيل كابل مكبر الصوت بلوحة النظام ].
.1 .2 .3 .4 .5 أعد وضع محرك أقراص SSDمن نوع M.2 أعد وضع البطارية أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. لوحة الإدخال/الإخراج )(IO إزالة لوحة الإدخال والإخراج .1 .2 .3 .4 .5 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD قم بإزالة غطاء القاعدة. أخرج البطارية إزالة مجموعة محرك الأقراص الثابتة .
.3قم بإزالة المسمارين اللولبيين ) (M2x4المثبت للوحة الإدخال/الإخراج بمجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .4ارفع لوحة الإدخال/الإخراج ،جنبًا إلى جنب مع الكابل ،خارج مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 تركيب لوحة الإدخال والإخراج .1باستخدام دعامات المحاذاة ،ضع لوحة الإدخال/الإخراج على مجموعة مسند راحة اليد ولوحة المفاتيح ].
.2أعد وضع المسمارين اللولبيين ) (M2x4المثبت للوحة الإدخال/الإخراج بمجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .3قم بتوصيل كابل البطارية الخلوية المصغرة بلوحة ) I/Oالإدخال والإخراج( ].[1 .4قم بتوصيل كابل لوحة وحدة الإدخال/الإخراج ) (I/Oبلوحة النظام ،وأغلق المزلاج لثبيت الكابل ].[2 .1أعد وضع مجموعة محرك الأقراص الثابتة .2أعد وضع البطارية. .3أعد وضع غطاء القاعدة.
.4أعد وضع بطاقة ذاكرة SD .5اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. لوحة اللمس إزالة مجموعة لوحة اللمس .1 .2 .3 .4 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD قم بإزالة غطاء القاعدة. أخرج البطارية .1افتح المزلاج وافصل كابل لوحة محرك الأقراص الثابتة وكابل لوحة اللمس عن لوحة النظام ].[2 ،1 .2انزع الشريط اللاصق الذي يثبت لوحة اللمس بمجموعة مسند راحة اليد ولوحة المفاتيح ].[3 .
.5قم بإزالة وضع المسامير اللولبية الأربعة ) (M2x2التي تثبت لوحة اللمس بمجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .6ارفع لوحة اللمس بعيدًا عن مجموعة مسند راحة اليد ولوحة المفاتيح ].
تركيب مجموعة لوحة اللمس ملاحظة :قم بالتأكد من محاذاة لوحة اللمس للأدلة المتاحة على مجموعة مسند راحة اليد ولوحة المفاتيح ،وأن الفجوة الموجودة على جانبي لوحة اللمس متساوية. .1ضع لوحة اللمس في الفتحة الموجودة بمجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .2أعد وضع المسامير اللولبية الأربعة ) (M2x2التي تثبت لوحة اللمس بمجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .3ضع رف لوحة اللمس في الفتحة الموجودة بمجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .
.5ثبت الشريط اللاصق الذي يثبت لوحة اللمس بمجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .6قم بإزاحة كابل المحرك وكابل لوحة اللمس إلى داخل الموصل الموجود في لوحة النظام وأغلق المزلاج لتثبيت الكابلات ].[3 ،2 .1 .2 .3 .4 أعد وضع البطارية أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك.
مجموعة الشاشة إزالة مجموعة الشاشة .1 .2 .3 .4 .5 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD قم بإزالة غطاء القاعدة. افصل كبل البطارية عن الموصل الموجود في لوحة النظام. إزالة بطاقة WLAN .1افتح المزلاج وافصل كابل الشاشة عن لوحة النظام ].[1 .2أخرج كابل الشاشة عن مساره عبر أدلة التوجيه الموجودة على مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .3انزع الشريط المثبت للهوائي اللاسلكي من لوحة النظام ].[3 .
.6ارفع المفصلات وإزالة مجموعة مسند راحة اليد ولوحة المفاتيح خارج الشاشة ].[2 ،1 .7بعد أداء جميع الخطوات السابقة ،تتبقى مجموعة الشاشة.
تركيب مجموعة الشاشة ملاحظة :تاكد من فتح المفصلات إلى الحد الاقصى قبل إعادة وضع مجموعة الشاشة على مجموعة مسند راحة اليد ولوحة المفاتيح. .1قم بمحاذاة مجموعة مسند راحة اليد ولوحة المفاتيح تحت المفصلات على مجموعة الشاشة ].[1 .2قم بتثبيت مجموعة مسند راحة اليد ولوحة المفاتيح في مجموعة الشاشة ].[2 .3اضغط على المفصلات للأسفل على لوحة النظام ،ومجموعة مسند راحة اليد ولوحة المفاتيح ].
.4أعد وضع المسامير اللولبية الخمسة ) (M2.5x5المثبتة للمفصلتين اليمنى واليسرى بلوحة النظام ومجموعة مسند راحة اليد ولوحة المفاتيح ].
.5قم بتوجيه كبل الشاشة عبر أدلة التوجيه الموجودة على مجموعة مسند راحة اليد ولوحة المفاتيح].[1 .6قم بتوصيل كابل الشاشة بالموصل الموجود على لوحة النظام ].[2 .7ثبت كبلات الهوائي بلوحة النظام ].
.1 .2 .3 .4 .5 أعد وضع بطاقة WLAN قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. لوحة زر التشغيل إزالة لوحة زر التشغيل .1 .2 .3 .4 .5 .6 .7 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD قم بإزالة غطاء القاعدة. افصل كبل البطارية عن الموصل الموجود في لوحة النظام.
.1 .2 .3 .4 .5 .6 .7 أعد تركيب مجموعة الشاشة أعد وضع مروحة النظام أعد وضع بطاقة WLAN قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. زر الطاقة إزالة زر التيار. .1 .2 .3 .4 .5 .6 .7 .8 .9 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك.
تثبيت زر التيار. .1ضع زر الطاقة في الفتحة الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[1 .2أعد وضع المسمار اللولبي ) (M2x2الذي يثبت زر الطاقة في مجموعة مسند راحة اليد ولوحة المفاتيح ].[2 .
.2 .3 .4 .5 .6 .7 .8 أعد تركيب مجموعة الشاشة إزالة مروحة النظام أعد وضع بطاقة WLAN قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. لوحة النظام إزالة لوحة النظام .1 .2 .3 .4 .5 .6 .7 .8 .9 .
.9أعد وضع بطاقة ذاكرة SD .10اتبع الإجراء الوارد في بعد العمل داخل جهاز الكمبيوتر الخاص بك منفذ مهايئ التيار إزالة منفذ مهايئ التيار .1 .2 .3 .4 .5 .6 .7 .8 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. إزالة بطاقة ذاكرة SD قم بإزالة غطاء القاعدة. أخرج البطارية إزالة بطاقة WLAN إزالة محرك SSD إزالة مجموعة الشاشة إزالة لوحة زر الطاقة .1افصل كابل مهايئ التيار وقم بتوجيه من لوحة النظام ].[2 ،1 .
.1 .2 .3 .4 .5 .6 .7 .8 أعد وضع زر الطاقة أعد تركيب مجموعة الشاشة أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع البطارية أعد وضع غطاء القاعدة أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. إطار الشاشة إزالة إطار الشاشة .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك.
تركيب إطار الشاشة قم بمحاذاة إطار الشاشة مع الغطاء الخلفي للشاشة ومجموعة الهوائي وقم بتثبيت إطار الشاشة في مكانه بعناية ].[1 .1أعد تركيب مجموعة الشاشة .
.3 .4 .5 .6 .7 .8 .9 .10 .11 أعد وضع مروحة النظام أعد وضع غرفة التبريد أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع الذاكرة قم بتوصيل كابل البطارية بالموصل الموجود في لوحة النظام. أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. الكاميرا إزالة الكاميرا .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .
تركيب الكاميرا .1قم بتوصيل كابل الكاميرا بوحدة الكاميرا ].[1 .2قم بتوجيه كبل الكاميرا عبر قنوات التوجيه ].[2 .3باستخدام عمود المحاذاة ،ضع وحدة الكاميرا في مجموعة الغطاء الخلفي للشاشة والهوائي ].
.1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 أعد وضع إطار الشاشة أعد تركيب مجموعة الشاشة أعد وضع مجموعة محرك الأقراص الثابتة أعد وضع مروحة النظام أعد وضع غرفة التبريد أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع البطارية أعد وضع غطاء القاعدة أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. لوحة الشاشة إزالة لوحة الشاشة .1 .2 .3 .4 .5 .6 .7 .8 .9 .
.11إزالة إطار الشاشة .12إزالة الكاميرا .1أزل المسامير اللولبية الأربعة ) (M2x2المثبتة للوحة الشاشة في مجموعة الغطاء الخلفي للشاشة والهوائي ].[1 .2ارفع لوحة الشاشة واقلبها ].[2 .3انزع الشريط الذي يثبت كابل الشاشة بالجزء الخلفي للوحة الشاشة ].[1 .4ارفع المزلاج وافصل كابل الشاشة عن موصل كابل لوحة الشاشة ].[2 .5ارفع لوحة الشاشة بعيدًا عن مجموعة الغطاء الخلفي للشاشة والهوائي ].
تركيب لوحة الشاشة .1ضع لوحة الشاشة على سطح مست ٍو ونظيف ].[1 .2قم بتوصيل كابل الشاشة بالموصل الموجود في الجزء الخلفي من لوحة الشاشة وقم بإغلاق المزلاج لتثبيت الكابل ].[2 .3قم بلصق الشريط الذي يثبت كابل الشاشة بالجزء الخلفي للوحة الشاشة ].[3 سا على عقب وضعها على مجموعة الغطاء الخلفي للشاشة والهوائي ].[4 .
.5قم بمحاذاة فتحات المسامير اللولبية الموجودة في لوحة الشاشة مع فتحات المسامير اللولبية الموجودة في مجموعة الغطاء الخلفي للشاشة والهوائي . .6قم بإعادة وضع المسامير اللولبية الأربعة ) (M2x2المثبتة للوحة الشاشة في مجموعة الغطاء الخلفي للشاشة والهوائي ].[1 .
.2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 أعد وضع إطار الشاشة أعد تركيب مجموعة الشاشة أعد وضع مجموعة محرك الأقراص الثابتة أعد وضع مروحة النظام أعد وضع غرفة التبريد أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع البطارية. أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. مفصلات الشاشة إزالة مفصلات الشاشة .1 .2 .3 .4 .5 .6 .7 .8 .9 .
تركيب مفصلات الشاشة .1قم بمحاذاة فتحات المسامير اللولبية الموجودة على المفصلات والدعامات مع فتحات المسامير اللولبية الموجودة على مجموعة الغطاء الخلفي للشاشة والهوائي ].[1 .2أعد وضع المسامير اللولبية الثمانية ) (M2.5x2.5والمسمارين ) (M2x2المسامير المثبتة للمفصلات بمجموعة الغطاء الخلفى للشاشة والهوائى ].
.1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 .13 أعد وضع لوحة الشاشة أعد وضع الكاميرا أعد وضع إطار الشاشة أعد تركيب مجموعة الشاشة أعد وضع مجموعة محرك الأقراص الثابتة أعد وضع مروحة النظام أعد وضع غرفة التبريد أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع البطارية أعد وضع غطاء القاعدة. أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. كابل الشاشة إزالة كبل الشاشة .1 .2 .
.9 .10 .11 .12 .13 إزالة غرفة التبريد إزالة مجموعة الشاشة إزالة إطار الشاشة إزالة لوحة الشاشة إزالة مفصلات الشاشة .1قم بإزالة كابل الكاميرا وكابل الشاشة من أدلة التوجيه الموجودة على مجموعة الغطاء الخلفي للشاشة والهوائي ].[1 .2انزع اللاصق الذي يثبت كبل الكاميرا ].[2 .3ارفع كبل الكاميرا وكبل الشاشة خارج مجموعة الغطاء الخلفي للشاشة والهوائى ].[3 تركيب كابل الشاشة .1ضع كابل الشاشة وكابل الكاميرا على مجموعة الغطاء الخلفي للشاشة والهوائي ].[1 .
.1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 .13 أعد وضع مفصلات الشاشة أعد وضع لوحة الشاشة أعد وضع إطار الشاشة أعد تركيب مجموعة الشاشة أعد وضع مجموعة محرك الأقراص الثابتة أعد وضع مروحة النظام أعد وضع غرفة التبريد أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع البطارية أعد وضع غطاء القاعدة أعد وضع بطاقة ذاكرة SD اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك.
.11 .12 .13 .14 .15 إزالة إطار الشاشة إزالة الكاميرا إزالة لوحة الشاشة إزالة مفصلات الشاشة إزالة كابل الشاشة بعد تنفيذ جميع الخطوات أعلاه ،يتبقى لك الغطاء الخلفي للشاشة.
تركيب الغطاء الخلفي للشاشة ضع الغطاء الخلفي للشاشة على سطح نظيف ومست ٍو. . .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 .13 .14 .15 أعد وضع كابل الشاشة أعد وضع مفصلات الشاشة أعد وضع لوحة الشاشة أعد وضع الكاميرا أعد وضع إطار الشاشة أعد تركيب مجموعة الشاشة أعد وضع مجموعة محرك الأقراص الثابتة أعد وضع مروحة النظام أعد وضع غرفة التبريد أعد وضع محرك SSD أعد وضع بطاقة WLAN أعد وضع البطارية. أعد وضع غطاء القاعدة.
.6إزالة بطاقة WLAN .7إزالة محرك SSD .8بإزالة مكبرات الصوت. .9إزالة البطارية الخلوية المصغرة. .10إزالة مجموعة محرك الأقراص الثابتة .11إزالة مروحة النظام .12إزالة غرفة التبريد .13قم بإزالة لوحة الإدخال والإخراج .14إزالة لوحة اللمس .15إزالة مجموعة الشاشة .16إزالة لوحة زر الطاقة .17إزالة زر الطاقة .18إزالة مفصلات الشاشة .19إزالة منفذ مهايئ التيار .
3 إعداد النظام يتيح لك إعداد النظام إمكانية إدارة أجهزة وتخصيص خيارات مستوى نظام الإدخال والإخراج الأساسي ) .
خيارات إعداد النظام ملاحظة :بنا ًء على والأجهزة التي تم تركيبها فيه ،قد تظهر العناصر المدرجة في هذا القسم أو قد لا تظهر. خيارات عامة جدول .2عام الخيار الوصف معلومات النظام تعرض المعلومات التالية: ● معلومات النظام :تعرض إصدار نظام الإدخال والإخراج الأساسي ) ،(BIOSورمز الخدمة ،ورمز الأصل ،ورمز الملكية ،وتاريخ الملكية ،وتاريخ التصنيع ،وكود الخدمة السريعة.
جدول .3تهيئة النظام )يتبع( الوصف الخيار ● ) SATA-2ممكن افتراضيًا( ● ) M.2 PCIe SSD-0ممكن افتراضيًا( Smart Reporting يتحكم هذا الحقل في إعداد تقرير الأخطاء بمحرك الأقراص الثابتة لمحركات الأقراص المدمجة أثناء بدء تشغيل النظام .يتم تعطيل تمكين خيار تقارير SMARTبشكل افتراضي. تهيئة منفذ USB تسمح لك بتمكين أو تعطيل وحدة تحكم USBالمدمجة لـ: ● ) Enable USB Boot Supportتمكين دعم تمهيد (USB ● Enable External USB Port يتم تمكين جميع الخيارات بشكل افتراضي.
جدول .4الأمان )يتبع( الخيار الوصف UEFI Capsule Firmware Updates يتحكم هذا الخيار فيما إذا كان هذا النظام يسمح بتحديثات نظام الإدخال والإخراج الأساسي ) (BIOSعبر حزم تحديث كبسولة UEFIأم لا .يتم تحديد هذا الخيار افتراضيًا .يؤدي تعطيل هذا الخيار إلى حظر تحديثات BIOSمن خدمات مثل Microsoft Windows Updateو(LVFS) Linux Vendor Firmware Service TPM 2.0 Security يتيح لك هذا الخيار التحكم فيما إذا كانت ) Trusted Platform Module (TPMظاهرة لنظام التشغيل .
جدول .
جدول .7الأداء )يتبع( الخيار الوصف Hyper-Thread Control يتيح لك تمكين أو تعطيل HyperThreadingفي المعالج. ● معطل ● ممكن -الإعداد الافتراضي إدارة الطاقة الخيار الوصف AC Behavior يتيح لك تمكين أو تعطيل خاصية التشغيل التلقائي لجهاز الكمبيوتر عند توصيل مهايئ تيار متردد. الإعداد الافتراضي) Wake on AC is not selected :التنبيه على التيار المتردد غير محدد(.
سلوك Behavior الخيار الوصف Adapter Warnings تتيح لك تمكين أو تعطيل رسائل تحذير إعداد النظام ) (BIOSعند استخدام مهايئات طاقة معينة. الإعداد الافتراضي) Enable Adapter Warnings :تمكين تحذيرات المهايئ( Numlock Enable يتيح لك تمكين خيار Numlockعند تمهيد الكمبيوتر. قم بتمكين الشبكة .يتم تمكين هذا الخيار افتراضيًا. Fn Lock Options يمكنك من السماح لمجموعات مفاتيح الاختصار Fn + Escبتغيير السلوك الرئيسي للمفاتيح من F1إلى ،F12بين وظائفها القياسية والثانوية .
وصف الخيار ● Bluetooth يتم تمكين جميع الخيارات بشكل افتراضي. ملاحظة :فيما يخص شبكات ،WLANيتم ربط عوامل التحكم في التمكين أو التعطيل ولا يمكن تمكينها أو تعطيلها بصورة مستقلة. تمكين جهاز الاتصال اللاسلكي يتيح لك تمكين أو تعطيل الأجهزة اللاسلكية الداخلية. ● WLAN ● Bluetooth يتم تمكين جميع الخيارات بشكل افتراضي. شاشة الصيانة الخيار الوصف Service Tag يعرض رمز الخدمة الخاص بجهاز الكمبيوتر الخاص بك.
كلمة مرور النظام والضبط جدول .8كلمة مرور النظام والضبط نوع كلمة المرور الوصف كلمة مرور النظام كلمة المرور التي يجب عليك إدخالها لتسجيل الدخول إلى النظام. كلمة مرور الضبط كلمة المرور التي يجب عليك إدخالها للوصول إلى ضبط BIOSوإحداث تغيير فيها والخاصة بالكمبيوتر. يمكنك إنشاء كلمة مرور النظام وكلمة مرور الضبط لتأمين الكمبيوتر. تنبيه :توفر ميزات كلمة المرور مستوى رئيسي من الأمان للبيانات الموجودة على الكمبيوتر.
4 استشكاف الأخطاء وإصلاحها الموضوعات: • • • • • • • تشخيصات التقييم المحسن للنظام قبل التمهيد )(ePSA أضواء النظام التشخيصية تحديث ) BIOSمفتاح (USB تحديث نظام الإدخال والإخراج الأساسي )(BIOS وسائط النسخ الاحتياطي وخيارات الاسترداد دورة تشغيل شبكة WiFi التخلص من الطاقة الزائدة تشخيصات التقييم المحسن للنظام قبل التمهيد )(ePSA تقوم تشخيصات ) ePSAالمعروفة أيضًا بتشخيصات النظام( بفحص كامل لجهازك .
● يعمل جهاز الكمبيوتر على البطارية والبطارية مشحونة بأكثر من 5بالمائة. ● جهاز الكمبيوتر في حالة السكون أو الإسبات أو قيد إيقاف التشغيل. ضوء التيار وحالة البطارية يومض باللون الكهرماني مع رموز صوتية تشير إلى حالات الفشل. على سبيل المثال ،يومض ضوء التيار وحالة البطارية باللون الكهرماني مرتين يتبعهما توقف مؤقت ثم يومض باللون الأبيض ثلاث مرات يتبعها توقف .ويستمر النمط 3 ،2هذا حتى يتم مشيرا إلى عدم اكتشاف ذاكرة أو ذاكرة .
تحديث نظام الإدخال والإخراج الأساسي )(BIOS قد تحتاج إلى تحديث نظام الإدخال والإخراج الأساسي ) (BIOSعندما يكون هناك تحديثًا متا ًحا أو بعد إعادة تركيب لوحة النظام. اتبع الخطوات التالية لتحديث نظام الإدخال والإخراج الأساسي ):(BIOS .1قم بتشغيل جهاز الكمبيوتر الخاص بك. .2قم بالانتقال إلى .www.dell.com/support .3انقر على ) Product supportدعم المنتج( ،وأدخل علامة الخدمة الخاصة بجهاز الكمبيوتر لديك ،ثم انقر على ) Submitإرسال(.
5 الحصول على المساعدة الموضوعات: • الاتصال بشركة Dell الاتصال بشركة Dell ملاحظة :إذا لم يكن لديك اتصال نشط بالإنترنت ،فيمكنك العثور على معلومات الاتصال على فاتورة الشراء الخاصة بك أو إيصال الشحن أو الفاتورة أو كتيب منتج .Dell توفر Dellالعديد من خيارات الدعم والخدمة القائمة على الهاتف والإنترنت .يختلف التوفر حسب البلد والمنتج ،وقد لا تتوفر بعض الخدمات في منطقتك .للاتصال بشركة Dellللاستفسار عن مسائل تتعلق بالمبيعات أو الدعم الفني أو خدمة العملاء: .