Dell Vostro 3591 (met optische schijf) Onderhoudshandleiding Regelgevingsmodel: P75F Regelgevingstype: PP75F013
Opmerkingen, voorzorgsmaatregelen,en waarschuwingen OPMERKING: Een OPMERKING duidt belangrijke informatie aan voor een beter gebruik van het product. WAARSCHUWING: WAARSCHUWINGEN duiden potentiële schade aan hardware of potentieel gegevensverlies aan en vertellen u hoe het probleem kan worden vermeden. GEVAAR: LET OP duidt het risico van schade aan eigendommen, lichamelijk letsel of overlijden aan. © 2020 Dell Inc. of zijn dochtermaatschappijen. Alle rechten voorbehouden.
Inhoudsopgave 1 Aan de computer werken............................................................................................................... 6 Veiligheidsinstructies............................................................................................................................................................. 6 Voordat u in de computer gaat werken........................................................................................................................
Warmteafleider.....................................................................................................................................................................37 De koelplaat verwijderen............................................................................................................................................... 37 De koelplaat installeren.......................................................................................................................................
Opties voor System Setup................................................................................................................................................. 79 Algemene opties.............................................................................................................................................................79 Systeeminformatie...................................................................................................................................................
1 Aan de computer werken Veiligheidsinstructies Vereisten Volg de onderstaande veiligheidsrichtlijnen om uw persoonlijke veiligheid te garanderen en de computer te beschermen tegen mogelijke schade. Tenzij anders aangegeven, wordt er bij elke procedure in dit document van de volgende veronderstellingen uitgegaan: • • U hebt de veiligheidsinformatie geraadpleegd die bij uw computer is geleverd.
Stappen 1. Zorg dat u de Veiligheidsinstructies volgt. 2. Zorg ervoor dat het werkoppervlak vlak en schoon is, om te voorkomen dat de computerkap bekrast raakt. 3. Zet de computer uit. 4. Verwijder alle stekkers van netwerkkabels uit de computer. WAARSCHUWING: Wanneer u een netwerkkabel wilt verwijderen, moet u eerst de connector van de netwerkkabel uit de computer verwijderen en daarna de netwerkkabel loskoppelen van het netwerkapparaat. 5.
• • • • • • • Antistatische mat - De antistatische mat is dissipatief en tijdens serviceprocedures kunnen er onderdelen op worden geplaatst. Uw polsband moet nauwsluitend zitten en het aardingssnoer moet aan de mat en aan onbewerkt metaal van het systeem waaraan u werkt zijn bevestigd wanneer u de antistatische mat gebruikt. Wanneer u het bovenstaande goed hebt uitgevoerd, kunt u serviceonderdelen uit de ESD-tas halen en die direct op de mat plaatsen.
6. Volg dezelfde technieken in omgekeerde volgorde om de last neer te zetten. Nadat u aan de computer heeft gewerkt Over deze taak Nadat u de onderdelen hebt vervangen of teruggeplaatst, moet u controleren of u alle externe apparaten, kaarten, kabels etc. hebt aangesloten voordat u de computer inschakelt. Stappen 1. Sluit alle telefoon- of netwerkkabels aan op uw computer. WAARSCHUWING: Steek voor het aansluiten van een netwerkkabel de kabel eerst in het netwerkapparaat en daarna in de computer. 2.
2 Onderdelen verwijderen en plaatsen Aanbevolen hulpmiddelen Voor de procedures in dit document heeft u het volgende gereedschap nodig: • • • Kruiskopschroevendraaier #0 Kruiskopschroevendraaier #1 Plastic pennetje OPMERKING: De schroevendraaier #0 is voor schroeven 0-1 en schroevendraaier #1 is voor schroeven 2-4. Lijst van schroeven De tabel bevat de lijst met schroeven die worden gebruikt voor het bevestigen van verschillende onderdelen. Tabel 1.
Component Type schroef Aantal Optische station-eenheid M2x4 Beugel van het optische station M2x3 Connectorkaart van het optische station M2x2 Grote schroefkop 1 Voedingsadapterpoort M2x3 Aan/uit-knopkaart M2x2 Grote schroefkop 1 Aan/uit-knop met vingerafdruklezer (optioneel) M2x2 Grote schroefkop 1 Thermische plaat van de Solid State-schijf M2x2 Grote schroefkop 1 Solid State-schijf M2 x 0,8 x 2,2 1 Systeemkaart M2x4 1 Touchpad M2x2 4 Touchpadbeugel M2x2 2 Beugel van de draadloz
De micro-SD-kaart installeren Stappen Schuif de micro-SD-kaart in de slot totdat deze op zijn plaats klikt.
Vervolgstappen 1. Volg de procedure in Nadat u in de computer hebt gewerkt Optische-schijfeenheid De optische-schijfeenheid verwijderen Vereisten 1. Volg de procedure in Voordat u in de computer gaat werken 2. Verwijder de micro-SD-kaart Stappen 1. Verwijder de enkele schroef (M2x4) waarmee de optische schijf aan het systeem vastzit [1]. 2. Schuif het optische station uit de computer [2]. 3.
De optische-schijfeenheid plaatsen Stappen 1. Lijn de beugel van de optische schijf uit met de schroefgaten op de optische schijf [1]. 2. Plaats de twee schroeven (M2x3) terug waarmee de beugel van de optische schijf aan de optische schijf wordt bevestigd [2]. 3. Plaats de optische schijf in het slot totdat deze vastklikt [1]. 4. Plaats de enkele (M2x4) schroef terug waarmee de optische schijf aan het systeem wordt bevestigd [2].
Vervolgstappen 1. Plaats de micro-SD-kaart terug 2. Volg de procedure in Nadat u in de computer hebt gewerkt Onderplaat De onderplaat verwijderen Vereisten 1. Volg de procedure in Voordat u in de computer gaat werken 2. Verwijder de SD-geheugenkaart 3. Verwijder het optische station Stappen 1. Draai de drie geborgde schroeven los [1]. 2. Verwijder de enkele schroef (M2x4), twee schroeven (M2x2) en zes schroeven (M2.5 x7) waarmee de onderplaat aan de palmsteunen toetsenbordeenheid is bevestigd [2, 3, 4].
3. Gebruik een wrik om de onderplaat van het systeem te verwijderen [5]. 4. Til de linkerkant van de onderplaat op en verwijder deze uit het systeem [1].
De onderplaat installeren Stappen 1. Plaats de onderplaat terug op de palmsteun- en toetsenbordeenheid [1]. 2. Plaats de twee (M2x2) schroeven terug en zes (M2.5x7) schroeven waarmee de onderplaat aan de palmsteun- en toetsenbordeenheid is bevestigd [3, 4].
Vervolgstappen 1. Plaats het optische station terug 2. Plaats de SD-geheugenkaart terug 3. Volg de procedure in Nadat u in de computer hebt gewerkt Batterij Voorzorgsmaatregelen voor de lithium-ionbatterij WAARSCHUWING: 18 • Wees voorzichtig bij het hanteren van lithium-ionbatterijen. • Ontlaad de batterij zo veel mogelijk voordat u deze uit het systeem verwijdert. Dit kan gedaan worden door de netadapter los te koppelen van het systeem, zodat de batterij kan leeglopen.
De batterij verwijderen Vereisten 1. 2. 3. 4. Volg de procedure in Voordat u in de computer gaat werken Verwijder de SD-geheugenkaart Verwijder het optische station Verwijder de onderplaat Stappen 1. Koppel de kabel van de batterij los van de systeemkaart [1]. 2. Verwijder de vier schroeven (M2x3) terug waarmee de batterij aan de palmsteun- en toetsenbordeenheid wordt bevestigd [2]. 3. Til de batterij weg van de palmsteun- en toetsenbordeenheid [3]. De batterij installeren Stappen 1.
Vervolgstappen 1. 2. 3. 4. Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt Geheugenmodules De geheugenmodule verwijderen Vereisten 1. 2. 3. 4. Volg de procedure in Voordat u in de computer gaat werken Verwijder de SD-geheugenkaart Verwijder de onderplaat Koppel de kabel van de batterij los van de connector op de systeemkaart. Stappen 1.
De geheugenmodule installeren Stappen 1. Lijn de uitsparing op de geheugenmodule uit met het lipje op de slot van de geheugenmodule en schuif de geheugenmodule onder een hoek stevig in de slot [1]. 2. Druk de geheugenmodule omlaag totdat de klemmen vastklikken [2]. OPMERKING: Als u geen klik hoort, verwijdert u de geheugenmodule en installeert u deze nogmaals.
Vervolgstappen 1. 2. 3. 4. 5. Sluit de kabel van de batterij aan op de connector op de systeemkaart. Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt WLAN-kaart De WLAN-kaart verwijderen Vereisten 1. 2. 3. 4. 5.
De WLAN-kaart installeren Over deze taak WAARSCHUWING: Plaats geen kabels onder de WLAN-kaart om beschadigingen te voorkomen. Stappen 1. Steek de WLAN-kaart in de connector op de systeemkaart [1]. 2. Sluit de WLAN-kabels aan op de connectoren op de WLAN-kaart [2]. 3. Plaats de WLAN-kaartbeugel om de WLAN-kabels aan de WLAN-kaart [3] te bevestigen. 4. Plaats de enkele (M2x3) schroef terug waarmee de WLAN-beugel aan de WLAN-kaart wordt bevestigd [4].
Vervolgstappen 1. 2. 3. 4. 5. Sluit de kabel van de batterij aan op de connector op de systeemkaart. Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt SSD/Intel Optane (optioneel) De M.2 2230 Solid State-schijf verwijderen Vereisten 1. 2. 3. 4. 5.
4. Draai de thermische plaat om. 5. Verwijder de enkele schroef (M2x2) waarmee de Solid State-schijf aan de thermische plaat wordt bevestigd [1]. 6. Til de Solid State-schijf uit de thermische plaat [2]. De M.2 2230 Solid State-schijf installeren Stappen 1. Plaats de Solid State-schijf in de slot van de thermische plaat [1]. 2. Plaats de enkele schroef (M2x2) terug waarmee de Solid State-schijf aan de thermische plaat wordt bevestigd [2].
3. Lijn de uitsparing op de Solid State-schijf uit met het lipje op de slot. 4. Schuif en plaats het lipje van de SSD in de SSD-slot [1, 2]. 5. Draai de geborgde schroef vast waarmee de thermische plaat aan de palmsteun- en toetsenbordeenheid is bevestigd [2]. 6. Plaats de enkele schroef (M2x3) terug waarmee de thermische plaat aan de palmsteun- en toetsenbordeenheid is bevestigd [3]. Vervolgstappen 1. 2. 3. 4. 5. 26 Sluit de kabel van de batterij aan op de connector op de systeemkaart.
De M.2 2280 Solid State-schijf of het Intel Optane geheugen verwijderen - optioneel Vereisten 1. 2. 3. 4. 5. Volg de procedure in Voordat u in de computer gaat werken Verwijder de SD-geheugenkaart Verwijder het optische station Verwijder de onderplaat Koppel de kabel van de batterij los van de connector op de systeemkaart. Stappen 1. Draai de geborgde schroef los waarmee de thermische plaat aan de palmsteun- en toetsenbordeenheid vastzit [1]. 2.
Vervolgstappen 1. 2. 3. 4. 5. Sluit de kabel van de batterij aan op de connector op de systeemkaart. Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt Knoopbatterij De knoopcelbatterij verwijderen Vereisten 1. 2. 3. 4. 5.
De knoopcelbatterij installeren Stappen 1. Steek de knoopcelbatterij met de positieve zijde omhoog in de batterijsocket op de I/O-kaart [1]. 2. Druk op de batterij totdat hij op zijn plaats klikt [2].
Vervolgstappen 1. 2. 3. 4. 5. Sluit de kabel van de batterij aan op de connector op de systeemkaart. Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt Harde schijf De harde-schijfeenheid verwijderen Vereisten 1. 2. 3. 4. 5. Volg de procedure in Voordat u in de computer gaat werken Verwijder de SD-geheugenkaart Verwijder het optische station Verwijder de onderplaat Verwijder de batterij Stappen 1.
4. Koppel de interposer los van de harde schijf. 5. Verwijder de vier schroeven (M3x3) waarmee de beugel van de harde schijf aan de harde schijf is bevestigd [1]. 6. Til de beugel van de harde schijf uit de harde schijf [2].
De harde-schijfeenheid installeren Stappen 1. Lijn de schroefgaten in de beugel van de harde schijf uit met de schroefgaten op de harde schijf [1]. 2. Plaats de vier schroeven (M3x3) terug waarmee de beugel van de harde schijf aan de harde schijf wordt bevestigd [2]. 3. Sluit de interposer aan op de harde schijf.
4. Lijn de schroefgaten van de harde-schijfeenheid uit met de schroefgaten op de palmsteun- en toetsenbordeenheid [1]. 5. Plaats de vier schroeven (M2x3) terug waarmee de harde-schijfeenheid aan de palmsteun- en toetsenbordeenheid wordt bevestigd [2]. 6. Sluit de kabel van de harde schijf aan op de systeemkaart en sluit de vergrendeling om de kabel te vergrendelen [3]. Vervolgstappen 1. 2. 3. 4. 5.
Systeemventilator De systeemventilator verwijderen Vereisten 1. 2. 3. 4. 5. Volg de procedure in Voordat u in de computer gaat werken Verwijder de SD-geheugenkaart Verwijder het optische station Verwijder de onderplaat Koppel de kabel van de batterij los van de connector op de systeemkaart. Stappen 1. Koppel deODD-kabel, beeldschermkabel en ventilatorkabel los van de connectoren op de systeemkaart [1, 2, 3]. 2. Verwijder de drie (M2.
De systeemventilator installeren Stappen 1. Lijn de schroefgaten op de ventilator uit met de schroefgaten op de palmsteun- en toetsenbordeenheid [1]. 2. Plaats de drie (M2.5 x5) schroeven terug waarmee de ventilator aan de palmsteun- en toetsenbordeenheid is bevestigd [2].
3. Leid de beeldschermkabel door de geleiders op de ventilator [1]. 4. Sluit deODD-kabel, beeldschermkabel en ventilatorkabel aan op de systeemkaart [3,2,1].
Vervolgstappen 1. 2. 3. 4. 5. Plaats de batterij terug Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt Warmteafleider De koelplaat verwijderen Vereisten 1. 2. 3. 4. 5. Volg de procedure in Voordat u in de computer gaat werken Verwijder de SD-geheugenkaart Verwijder de onderplaat Verwijder de batterij Verwijder de systeemventilator Stappen 1.
De koelplaat installeren Stappen 1. Plaats de koelplaat op de systeemkaart en lijn de schroefgaten op de koelplaat uit met de schroefgaten op de systeemkaart [1]. 2. Draai de vier geborgde schroeven waarmee de koelplaat op de systeemkaart is bevestigd in de juiste volgorde (zoals aangegeven op de koelplaat) vast [2]. Vervolgstappen 1. 2. 3. 4. 5. Sluit de kabel van de batterij aan op de connector op de systeemkaart.
De koelplaat installeren Stappen 1. Plaats de koelplaat op de systeemkaart en lijn de schroefgaten op de koelplaat uit met de schroefgaten op de systeemkaart [1]. 2. Plaats de drie de schroeven (M2x3) waarmee de koelplaat aan de systeemkaart is bevestigd [2]. 3. Draai de vier geborgde schroeven waarmee de koelplaat aan de systeemkaart is bevestigd in de juiste volgorde (zoals aangegeven op de koelplaat) vast [3].
Vervolgstappen 1. 2. 3. 4. 5. Sluit de kabel van de batterij aan op de connector op de systeemkaart. Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt Luidsprekers De luidsprekers verwijderen Vereisten 1. 2. 3. 4. 5. 6.
De luidsprekers installeren Over deze taak OPMERKING: Als de rubberen dichtingsringen loskomen bij het verwijderen van de luidsprekers, dient u ze terug te duwen voordat u de luidsprekers terugplaatst. Stappen 1. Gebruik de uitlijnpunten en rubberen dichtingsringen om de luidsprekers in de slots op de palmsteun- en toetsenbordeenheid te plaatsen [1]. 2. Leid de luidsprekerkabel door de kabelgeleiders op de palmsteun- en toetsenbordeenheid [2]. 3.
Vervolgstappen 1. 2. 3. 4. 5. 6. Plaats de SSD terug Plaats de batterij terug Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt I/O-kaart De I/O-kaart verwijderen Vereisten 1. 2. 3. 4. 5. 6. Volg de procedure in Voordat u in de computer gaat werken Verwijder de SD-geheugenkaart Verwijder het optische station Verwijder de onderplaat Verwijder de batterij Verwijder de harde-schijfeenheid Stappen 1.
3. Verwijder de enkele (M2x4) schroef terug waarmee de I/O-kaart aan de palmsteun- en toetsenbordeenheid is bevestigd [1]. 4. Til de I/O-kaart samen met de kabel weg van de palmsteun- en toetsenbordeenheid [2]. OPMERKING: Wanneer de I/O-kaart kabel niet op de systeemkaart is aangesloten, treedt er een RTC-fout op. Deze fout treedt op wanneer de RTC/knoopcelbatterij, de I/O-kaart of de systeemkaart wordt verwijderd.
Een foutbericht voor ongeldige configuratie wordt weergegeven waarin u wordt gevraagd om het BIOS te openen en de datum en tijd te configureren. De computer begint normaal te werken nadat de datum en tijd zijn ingesteld. De I/O-kaart installeren Stappen 1. Gebruik de uitlijnpunten om de I/O-kaart op de palmsteun- en toetsenbordeenheid te plaatsen [1]. 2. Plaats de enkele (M2x4) schroef terug waarmee de I/O-kaart aan de palmsteun- en toetsenbordeenheid is bevestigd [2]. 3.
Vervolgstappen 1. 2. 3. 4. 5. 6. Plaats de harde-schijfeenheid terug Plaats de batterij terug Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt Toetsenblok De touchpadeenheid verwijderen Vereisten 1. 2. 3. 4. 5. Volg de procedure in Voordat u in de computer gaat werken Verwijder de SD-geheugenkaart Verwijder het optische station Verwijder de onderplaat Verwijder de batterij Stappen 1.
3. Verwijder de twee schroeven (M2x2) waarmee de beugel van de touchpad aan de palmsteun- en toetsenbordeenheid is bevestigd [1]. 4. Til de beugel van de touchpad weg van de palmsteun- en toetsenbordeenheid [2]. 5. Verwijder de vier schroeven (M2x2) waarmee de touchpad aan de palmsteun- en toetsenbordeenheid wordt bevestigd [1]. 6. Til de touchpad weg van de palmsteun- en toetsenbordeenheid [2].
De touchpadeenheid installeren Over deze taak OPMERKING: Zorg ervoor dat de touchpad is uitgelijnd met de geleiders op de palmsteun- en toetsenbordeenheid, en dat de speling aan beide zijden van de touchpad gelijk is. Stappen 1. Plaats de touchpad in de slot op de palmsteun- en toetsenbordeenheid [1]. 2. Plaats de vier schroeven (M2x2) terug waarmee de touchpad aan de palmsteun- en toetsenbordeenheid wordt bevestigd [2].
3. Plaats de touchpadbeugel in de slot op de palmsteun- en toetsenbordeenheid [1]. 4. Plaats de twee schroeven (M2x2) terug waarmee de touchpadbeugel aan de palmsteun- en toetsenbordeenheid wordt bevestigd [2]. 5. Bevestig de tape aan waarmee de touchpad aan de palmsteun- en toetsenbordeenheid wordt bevestigd [1]. 6. Schuif de kabel van de harde schijf en de kabel van de touchpad in de connector op de systeemkaart en sluit de vergrendeling om de kabels vast te zetten [2, 3].
Vervolgstappen 1. 2. 3. 4. 5. Plaats de batterij terug Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt Beeldschermassemblage De beeldschermeenheid verwijderen Vereisten 1. 2. 3. 4. 5. 6.
4. Verwijder de vijf (M2.5x5) schroeven waarmee de linker en rechter scharnieren op de systeemkaart en de palmsteun- en toetsenbordeenheid zijn bevestigd [1]. 5. Til de scharnieren op [1]. Til de palmsteun- en toetsenbordeenheid op onder een hoek [2]. 6. Til de scharnieren omhoog.
7. Na het uitvoeren van alle voorgaande stappen, blijft alleen het beeldscherm over.
De beeldschermeenheid installeren Over deze taak OPMERKING: Zorg dat de scharnieren maximaal zijn geopend voordat het beeldscherm terug wordt geplaatst op de palmsteun- en toetsenbordeenheid. Stappen 1. Lijn de palmsteun- en toetsenbordeenheid uit en plaats ze onder de scharnieren op het beeldscherm [1]. 2. Plaats de palmsteun- en toetsenbordeenheid op de beeldschermeenheid [2]. 3. Druk de scharnieren omlaag op de systeemkaart en de palmsteun- en toetsenbordeenheid [3]. 4. Plaats de vijf (M2.
5. Leid de beeldschermkabel door de kabelgeleiders op de palmsteun- en toetsenbordeenheid [1]. 6. Bevestig de antennekabels aan de systeemkaart [2]. 7. Sluit de beeldschermkabel en de kabel van het optische station aan op de connector op de systeemkaart [3, 4].
Vervolgstappen 1. 2. 3. 4. 5. Plaats de WLAN terug Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt Montagekader van het beeldscherm De bezel van het beeldscherm verwijderen Vereisten 1. 2. 3. 4. 5. Volg de procedure in Voordat u in de computer gaat werken Verwijder de SD-geheugenkaart Verwijder het optische station Verwijder de onderplaat Verwijder de beeldschermeenheid Stappen 1.
Vervolgstappen 1. 2. 3. 4. 5. 6. 7. Plaats de beeldschermeenheid terug Plaats de harde-schijfeenheid terug Sluit de kabel van de batterij aan op de connector op de systeemkaart. Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt Aan-uitknopkaart De aan/uit-knopkaart verwijderen Vereisten 1. 2. 3. 4. 5. 6. 7. 8.
4. Til de aan/uit-knopkaart samen met de kabel weg van de palmsteun- en toetsenbordeenheid [4]. De aan/uit-knopkaart installeren Stappen 1. Plaats de aan/uit-knopkaart in de slot op de palmsteun- en toetsenbordeenheid [1]. 2. Plaats de enkele schroef (M2x2) terug waarmee de aan/uit-knopkaart op de palmsteun- en toetsenbordeenheid is bevestigd [2]. 3. Bevestig de geleidende tape aan de aan/uit-knopkaart [3]. 4.
Vervolgstappen 1. 2. 3. 4. 5. 6. 7. 8. Plaats de beeldschermeenheid terug Plaats de systeemventilator terug Plaats de WLAN terug Sluit de kabel van de batterij aan op de connector op de systeemkaart. Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt Moederbord De systeemkaart verwijderen Vereisten 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
Stappen 1. Koppel de volgende kabels los van de systeemkaart: a) b) c) d) e) f) Voedingsadapterpoortkabel [1]. Voedingskabel [2]. I/O-kaartkabel [3]. Kabel van touchpad [4]. Toetsenbordkabel [5]. Luidsprekerkabel [6]. 2. Verwijder de enkele schroef (M2x4) waarmee de systeemkaart aan de palmsteun- en toetsenbordeenheid is bevestigd [1]. 3. Til de systeemkaart weg van de palmsteun- en toetsenbordeenheid [2].
De systeemkaart installeren Stappen 1. Lijn het schroefgat op de systeemkaart uit met het schroefgat in de palmsteun- en toetsenbordeenheid [1]. 2. Plaats de enkele schroef (M2x4) terug waarmee de systeemkaart aan de palmsteun- en toetsenbordeenheid wordt bevestigd [2].
3. Sluit de volgende kabels aan op de systeemkaart: a) b) c) d) e) f) 60 Luidsprekerkabel [1]. Toetsenbordkabel [2]. Kabel van touchpad [3]. I/O-kaartkabel [4]. Voedingskabel [5]. Voedingsadapterpoortkabel [6].
Vervolgstappen 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Plaats de aan/uit-knopkaart terug Plaats de beeldschermeenheid terug Plaats de koelplaat terug Plaats de systeemventilator terug Plaats de harde-schijfeenheid terug Plaats de SSD terug Plaats de WLAN terug Plaats de batterij terug Plaats de onderplaat terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt Netadapterpoort De voedingsadapterpoort verwijderen Vereisten 1. 2. 3. 4. 5.
6. 7. 8. 9. Verwijder de WLAN Verwijder de SSD Verwijder de beeldschermeenheid Verwijder de aan/uit-knopkaart Stappen 1. Koppel de kabel van de voedingsadapter los en leid die weg van de systeemkaart [1, 2]. 2. Verwijder de enkele schroef (M2x3) waarmee de voedingsadapterpoort aan de palmsteun- en toetsenbordeenheid vastzit [3]. 3. Til de voedingsadapterpoort samen met zijn kabel omhoog, weg van de palmsteun- en toetsenbordeenheid [4]. De voedingsadapterpoort installeren Stappen 1.
Vervolgstappen 1. 2. 3. 4. 5. 6. 7. 8. 9. Plaats de aan/uit-knopkaart terug Plaats de beeldschermeenheid terug Plaats de SSD terug Plaats de WLAN terug Plaats de batterij terug Plaats de onderplaat terug Plaats het optische station terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt Camera De camera verwijderen Vereisten 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Stappen 1. Wrik met een plastic pennetje de camera voorzichtig van de achterzijde van het beeldscherm en de antenne-eenheid [1]. 2. Koppel de camerakabel los van de cameramodule [2]. 3. Til de cameramodule van het achterpaneel van het beeldscherm en de antenne-eenheid [3]. De camera installeren Stappen 1. Sluit de camerakabel aan op de cameramodule [1]. 2. Gebruik het uitlijnpunt om de cameramodule op het achterpaneel van het beeldscherm en de antenne-eenheid te bevestigen [2]. 3.
Vervolgstappen 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Plaats de bezel van het beeldscherm terug Plaats de beeldschermeenheid terug Plaats de harde-schijfeenheid terug Plaats de systeemventilator terug Plaats de koelplaat terug Plaats de SSD terug Plaats de WLAN terug Plaats de batterij terug Plaats de onderplaat terug Plaats de SD-geheugenkaart terug Volg de procedure in Nadat u in de computer hebt gewerkt Beeldschermpaneel Het beeldschermpaneel verwijderen Vereisten 1. 2. 3. 4. 5. 6. 7.
8. 9. 10. 11. 12. 13. Verwijder de harde-schijfeenheid Verwijder de systeemventilator Verwijder de koelplaat Verwijder de beeldschermeenheid Verwijder de bezel van het beeldscherm Verwijder de camera Stappen 1. Verwijder de vier schroeven (M2x2) waarmee het beeldschermpaneel aan de achterplaat van het beeldscherm en de antenne-eenheid is bevestigd [1]. 2. Til het beeldschermpaneel omhoog en kantel deze om [2]. 3.
Het beeldschermpaneel installeren Stappen 1. Plaats het beeldschermpaneel op een vlak en schoon oppervlak [1] 2. Sluit de beeldschermkabel aan op de connector op de achterplaat van het beeldschermpaneel en sluit de vergrendeling om de kabel vast te zetten [2]. 3. Bevestig de tape waarmee de beeldschermkabel wordt bevestigd aan de achterzijde van het beeldschermpaneel [3]. 4. Draai het beeldschermpaneel om en plaats dit op het achterpaneel van het beeldscherm en de antenne-eenheid [4].
5. Lijn de schroefgaten in het beeldschermpaneel uit met de schroefgaten in het achterpaneel van het beeldscherm en de antenneeenheid. 6. Plaats de vier schroeven (M2x2) terug waarmee het beeldschermpaneel aan het achterpaneel van het beeldscherm en de antenneeenheid is bevestigd [1].
Vervolgstappen 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
De beeldschermscharnieren installeren Stappen 1. Lijn de schroefgaten op de scharnieren en beugels uit met de schroefgaten op het achterpaneel van het beeldscherm en de antenneeenheid [1]. 2. Plaats de acht schroeven (M2.5x2.5) en twee schroeven (M2x2) terug waarmee het beeldschermpaneel aan het achterpaneel van het beeldscherm en de antenne-eenheid is bevestigd [3,2 ].
Vervolgstappen 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Verwijder de batterij Verwijder de WLAN Verwijder de SSD Verwijder de harde-schijfeenheid Verwijder de systeemventilator Verwijder de koelplaat Verwijder de beeldschermeenheid Verwijder de bezel van het beeldscherm Verwijder het beeldschermpaneel Verwijder de beeldschermscharnieren Stappen 1. Koppel de camerakabel op het achterpaneel van het beeldscherm en de antenne-eenheid [1] los. 2. Trek de tape los waarmee de camerakabel is vastgemaakt [2]. 3.
Vervolgstappen 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
Het achterpaneel van het beeldscherm installeren Over deze taak Plaats het achterpaneel van het beeldscherm op een schoon en vlak oppervlak. Vervolgstappen 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
Polssteun- en toetsenbordeenheid De palmsteun- en toetsenbordeenheid verwijderen Vereisten 1. Volg de procedure in Voordat u in de computer gaat werken 2. Verwijder de SD-geheugenkaart 3. Verwijder het optische station 4. Verwijder de onderplaat 5. Verwijder de batterij 6. Verwijder het geheugen 7. Verwijder de WLAN 8. Verwijder de SSD 9. Verwijder de luidsprekers 10. Verwijder de knoopcelbatterij 11. Verwijder de harde-schijfeenheid 12. Verwijder de systeemventilator 13. Verwijder de koelplaat 14.
Onderdelen verwijderen en plaatsen 77
3 Systeeminstallatie Met systeeminstallatie kunt u uw hardware beheren en BIOS-niveau-opties opgeven. Vanuit de systeeminstallatie kunt u: • • • • • De NVRAM-instellingen wijzigen na het toevoegen of verwijderen van hardware; De configuratie van de systeemhardware bekijken; Geïntegreerde apparaten in- of uitschakelen; Grenswaarden voor prestatie- en energiebeheer instellen; De computerbeveiliging beheren.
Opties voor System Setup OPMERKING: Afhankelijk van de en de geïnstalleerde apparaten kunnen de onderdelen die in dit gedeelte worden vermeld wel of niet worden weergegeven. Algemene opties Tabel 2.
Optie Beschrijving • • • SATA Operation Disabled (Uitgeschakeld) = De interne LAN staat uit en is onzichtbaar voor het besturingssysteem. Enabled (Ingeschakeld) = De interne LAN is ingeschakeld. Enabled w/PXE (Ingeschakeld met PXE) = De interne LAN is ingeschakeld (met PXEopstartbewerking) (standaard geselecteerd) Hiermee kunt u de werkingsmodus van de geïntegreerde controller van de vaste schijf configureren.
Optie Beschrijving Password Configuration Hiermee kunt u het minimum- en maximumaantal tekens instellen dat is toegestaan voor een beheerderwachtwoord en het systeemwachtwoord. De aantal tekens ligt tussen 4 en 32. Password Bypass Met deze optie kunt u tijdens het opnieuw opstarten van het systeem het System (Boot) Password (Systeem (Boot) wachtwoord) en het wachtwoord van de interne vaste schijf omzeilen.
Optie Beschrijving SMM Security Mitigation Hiermee kunt u extra instellingen voor UEFI SMM-beveiligingsbeperking in- of uitschakelen. Deze optie is niet standaard ingeschakeld. Secure Boot (Veilig opstarten) Tabel 5. Secure Boot (Beveiligd opstarten) Optie Beschrijving Secure Boot Enable Hiermee kunt u de functie Beveiligd opstarten inschakelen of uitschakelen. • Secure Boot Enable Deze optie is standaard geactiveerd.
Optie Beschrijving Enclave Memory Size Met deze optie stelt u SGX Enclave Reserve Memory Size (Geheugengrootte reserveren voor SGX-enclave) in. Klik op een van de volgende opties: • • • 32 MB 64 MB 128 MB - standaard Prestaties Tabel 7. Prestaties Optie Beschrijving Multi Core Support Dit veld specificeert of één of alle kernen zijn ingeschakeld. Bij meerdere kernen zullen de prestaties van bepaalde programma's toenemen.
Optie Beschrijving • Select Days (Dagen selecteren) Standaardinstelling: Disabled (Uitgeschakeld) USB Wake Support Hiermee kunt USB-apparaten inschakelen zodat het systeem in de stand-bymodus weer wordt ingeschakeld. OPMERKING: Deze functie werkt alleen als de netadapter is aangesloten. Als u de voedingsdapter verwijdert voordat de computer in de wachtstand staat, wordt de stroomtoevoer naar alle USBpoorten onderbroken om batterijvoeding te besparen.
Optie Beschrijving Fastboot Hiermee kunt u het opstarten versnellen door enkele compatibiliteitsstappen over te slaan. De opties zijn: • • • Minimal (Minimaal): standaard ingeschakeld Thorough (Grondig) Auto (Automatisch) Extended BIOS POST Time Hiermee kunt u een extra vertraging voor het opstarten instellen. De opties zijn: • • • 0 seconds (0 seconden): standaard ingeschakeld.
Beschrijving van de optie Alle opties zijn standaard ingeschakeld. Scherm Maintenance (Onderhoud) Optie Beschrijving Service Tag Hier wordt het servicelabel van uw computer weergegeven. Asset Tag Hier kunt u een inventaristag voor de computer maken als er nog geen inventaristag is ingesteld. Deze optie is niet standaard ingeschakeld. BIOS Downgrade Dit veld beheert het terugzetten van de systeemfirmware naar vorige revisies.
Systeem- en installatiewachtwoord Tabel 8. Systeem- en installatiewachtwoord Type wachtwoord Beschrijving System Password (Systeemwachtwoord) Wachtwoord dat moet worden ingevuld om aan uw systeem in te loggen. Installatiewachtwoord Wachtwoord dat moet worden ingevuld voor toegang en het aanbrengen van wijzigingen aan de BIOS-instellingen van uw computer. U kunt ter beveiliging van uw computer een wachtwoord voor het systeem en de installatie aanmaken.
Over deze taak Druk na het aanzetten of opnieuw opstarten van de computer onmiddellijk op F2 om naar de System Setup te gaan. Stappen 1. Selecteer System Security in het scherm System BIOS of System Setup en druk op Enter. Het scherm System Security (Systeembeveiliging) wordt geopend. 2. Controleer in het scherm System Security (Systeembeveiliging) of Password Status (Wachtwoordstatus) op Unlocked (Ontgrendeld) staat. 3.
4 Problemen oplossen Diagnostische Enhanced Pre-Boot System Assessment (ePSA) Over deze taak De ePSA-diagnose (ook bekend als systeemdiagnose) voert een volledige controle van uw hardware. ePSA maakt deel uit van het BIOS en wordt door het BIOS intern gestart.
Het statuslampje van de voeding en de batterij knippert oranje en pieptooncodes geven aan dat er storingen zijn. Bijvoorbeeld, het statuslampje van de voeding en de batterij knippert twee keer oranje gevolgd door en pauze, en knippert vervolgens drie keer gevolgd door een pauze. Dit 2,3-patroon houdt aan totdat de computer is uitgeschakeld en geeft aan dat er geen geheugen of RAM werd gevonden.
Het BIOS flashen Over deze taak Mogelijk moet u het BIOS flashen wanneer er een update beschikbaar is of na het vervangen of terugplaatsen van het moederbord. Volg deze stappen om het BIOS te flashen: Stappen 1. Zet de computer aan. 2. Ga naar www.dell.com/support. 3. Klik op Product support (productondersteuning), voer de servicetag van uw computer in en klik op Submit (verzenden).
Stappen 1. Zet de computer uit. 2. Koppel de netadapter los van de computer. 3. Houd de aan-uitknop 15 seconden seconden lang ingedrukt om de reststroom te verwijderen. 4. Sluit de netadapter weer aan op de computer. 5. Zet de computer aan.
5 Behulpzame informatie vinden Onderwerpen: • Contact opnemen met Dell Contact opnemen met Dell Vereisten OPMERKING: Als u geen actieve internetverbinding hebt, kunt u contactgegevens ook vinden op uw factuur, pakbon, rekening of productcatalogus van Dell. Over deze taak Dell biedt diverse online en telefonische ondersteunings- en servicemogelijkheden. De beschikbaarheid verschilt per land en product en sommige services zijn mogelijk niet beschikbaar in uw regio.