Dell Vostro 3591 (With optical drive) Service Manual Regulatory Model: P75F Regulatory Type: PP75F013
Märkused, ettevaatusabinõud ja hoiatused MÄRKUS: MÄRKUS tähistab olulist teavet, mis aitab teil seadet paremini kasutada. ETTEVAATUST: ETTEVAATUST tähistab kas võimalikku riistvarakahjustust või andmekadu ja annab teavet probleemi vältimise kohta. HOIATUS: HOIATUS tähistab võimalikku omandi kahjustumist või inimeste vigastusi või surma. © 2020 Dell Inc. või selle tütarettevõtted. Kõik õigused on kaitstud. Dell, EMC ja muud kaubamärgid on ettevõtte Dell Inc. või selle tütarettevõtete kaubamärgid.
Contents 1 Arvutiga töötamine....................................................................................................................... 6 Ohutusjuhised.........................................................................................................................................................................6 Enne arvuti sees toimetamist.........................................................................................................................................
Jahutusradiaator..................................................................................................................................................................36 Removing the heatsink................................................................................................................................................. 36 Installing the heatsink..........................................................................................................................................
Süsteemi seadistusvalikud.................................................................................................................................................. 78 Üldised valikud................................................................................................................................................................78 Süsteemiandmed.................................................................................................................................................
1 Arvutiga töötamine Ohutusjuhised Eeltingimused Et kaitsta arvutit viga saamise eest ja tagada enda ohutus, kasutage järgmisi ohutusjuhiseid. Kui pole teisiti märgitud, eeldatakse igas selle dokumendi protseduuris, et on täidetud järgmised tingimused. • • Olete lugenud arvutiga kaasas olevat ohutusteavet. Komponendi saab asendada või, kui see on eraldi ostetud, paigaldada eemaldamisprotseduurile vastupidises järjekorras.
5. Ühendage arvuti ja kõik selle küljes olevad seadmed elektrivõrgust lahti. 6. Vajutage emaplaadi maandamiseks pikalt toitenuppu, kuni arvuti on lahti ühendatud. MÄRKUS: Elektrostaatilise lahenduse vältimiseks maandage ennast, kasutades randme-maandusriba või puudutades regulaarselt värvimata metallpinda samal ajal, kui puudutada arvuti taga olevat liidest.
• • • Töökeskkond: enne ESD välikomplekti kasutamist hinnake olukorda kliendi asukohas. Näiteks serverikeskkondade puhul kasutatakse komplekt teisiti kui kaasaskantava või lauaarvutikeskkonna korral. Serverid on tavaliselt paigaldatud andmekeskuses olevale riiulile, samas kui kaasaskantavad ja lauaarvutid asuvad üldjuhul kontorilaudadel või -boksides. Leidke iga kord tasane tööpind, mis oleks vaba ja ESD-komplekti ja parandatava süsteemi jaoks piisavalt suur.
2 Komponentide eemaldamine ja paigaldamine Soovitatud tööriistad Käesolevas dokumendis olevate toimingute jaoks võib olla vaja järgmisi tööriistu: • • • Ristpeakruvikeeraja nr 0 Ristpeakruvikeeraja nr 1 Plastvarras MÄRKUS: Ristpeakruvikeeraja nr 0 on kruvide 0–1 jaoks ja ristpeakruvikeeraja nr 1 on kruvide 2–4 jaoks. Screw list The table provides the list of screws that are used for securing different components. Table 1. Screw list Component Screw type Quantity Base cover M2.
Component Screw type Quantity Optical-drive assembly M2x4 Optical-drive bracket M2x3 2 Optical-drive connector board M2x2 Big Head 1 Power-adapter port M2x3 1 Power-button board M2x2 Big Head 1 Power button with fingerprint reader (optional) M2x2 Big Head 1 Solid-state drive to thermal plate M2x2 Big Head 1 Solid-state drive M2x0.8x2.
Installing the Micro Secure Digital card Steps Slide the micro secure digital into the slot until it clicks into place.
Next steps 1. Follow the procedure in after working inside your computer Optilise draivi moodul Removing the optical drive assembly Prerequisites 1. Follow the procedure in before working inside your computer 2. Remove the micro SD card Steps 1. Remove the single (M2x4) screw that secures the optical drive to the system [1]. 2. Slide the optical drive out of the computer [2]. 3. Remove the two (M2x3) screws that secure the optical drive bracket to the optical drive [1]. 4.
Installing the optical drive assembly Steps 1. Align the optical drive bracket to the screw holes on the optical drive [1]. 2. Replace the two (M2x3) screws that secure the optical drive bracket to the optical drive [2]. 3. Insert the optical drive into the slot until it clicks into place [1]. 4. Replace the single (M2x4) screw that secures the optical drive to the system [2].
Next steps 1. Replace the micro SD card 2. Follow the procedure in after working inside your computer tagakaas Removing the base cover Prerequisites 1. Follow the procedure in before working inside your computer 2. Remove the SD memory card 3. Remove the optical drive assembly Steps 1. Loosen the three captive screws [1]. 2. Remove the single (M2x4) screw, two (M2x2) screws, and six (M2.5x7) screws that secure the base cover to the palmrest and keyboard assembly [2, 3, 4].
3. Use a prying tool and remove the base cover from the system [5]. 4. Lift the left side of the base cover and remove it off the system [1].
Installing the base cover Steps 1. Replace the base cover on the palmrest and keyboard assembly [1]. 2. Replace the two (M2x2) screws, and six (M2.5x7) screws that secure the base cover to the palmrest and keyboard assembly [3, 4].
Next steps 1. Replace the optical drive assembly 2. Replace the SD memory card 3. Follow the procedure in after working inside your computer aku Liitiumioonaku ettevaatusabinõud ETTEVAATUST: • Olge liitiumioonakude käsitsemisel ettevaatlik. • Tühjendage aku enne selle süsteemist eemaldamist nii palju kui võimalik. Seda on võimalik teha, kui eemaldate vahelduvvooluadapteri süsteemist, et aku saaks tühjendada.
Removing the battery Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive assembly Remove the base cover Steps 1. Disconnect the battery cable from the system board [1]. 2. Remove the four (M2x3) screws that secure the battery to the palmrest and keyboard assembly [2]. 3. Lift the battery off the palmrest and keyboard assembly [3]. Installing the battery Steps 1.
Next steps 1. 2. 3. 4. Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Mälumoodulid Removing the memory module Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer Remove the SD memory card Remove the base cover Disconnect the battery cable from the connector on the system board. Steps 1. Pry the clips securing the memory module until the memory module pops-up [1]. 2.
Installing the memory module Steps 1. Align the notch on the memory module with the tab on the memory module slot and slide the memory module firmly into the slot at an angle [1]. 2. Press the memory module down until the clips secure it [2]. NOTE: If you do not hear the click, remove the memory module and reinstall it.
Next steps 1. 2. 3. 4. 5. Connect the battery cable to the connector on the system board. Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer WLAN-kaart Removing the WLAN card Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive assembly Remove the base cover Disconnect the battery cable from the connector on the system board.
Installing the WLAN card About this task CAUTION: To avoid damage to the WLAN card, do not place any cables under it. Steps 1. Replace the WLAN card into the connector on the system board [1]. 2. Connect the WLAN cables to the connectors on the WLAN card [2]. 3. Place the WLAN card bracket to secure the WLAN cables to the WLAN card [3]. 4. Replace the single (M2x3) screw to secure the WLAN bracket to the WLAN card [4].
Next steps 1. 2. 3. 4. 5. Connect the battery cable to the connector on the system board. Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Solid-state drive/Intel Optane (Optional) Removing the M.2 2230 Solid-state drive Prerequisites 1. 2. 3. 4. 5.
4. Turn the thermal plate over. 5. Remove the single (M2x2) screw that secures the solid-state drive to the thermal plate [1]. 6. Lift the solid-state drive off the thermal plate [2]. Installing the M.2 2230 Solid-state drive Steps 1. Place the solid-state drive into the thermal plate slot [1]. 2. Replace the single (M2x2) screw that secures the solid-state drive to the thermal plate [2].
3. Align the notch on the solid-state drive with the tab on the solid-state drive slot. 4. Slide and insert the tab of the solid-state drive into the solid-state drive slot [1,2]. 5. Tighten the captive screw that secures the thermal plate to the palmrest and keyboard assembly [2]. 6. Replace the single (M2x3) screw that secures the thermal plate to the palmrest and keyboard assembly [3]. Next steps 1. 2. 3. 4. 5. Connect the battery cable to the connector on the system board.
Removing the M.2 2280 Solid-state drive or Intel Optane memory - Optional Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive assembly Remove the base cover Disconnect the battery cable from the connector on the system board. Steps 1. Loosen the captive screw that secures the thermal plate to the palmrest and keyboard assembly [1]. 2.
Next steps 1. 2. 3. 4. 5. Connect the battery cable to the connector on the system board. Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Nööppatarei Removing the coin-cell Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive assembly Remove the base cover Disconnect the battery cable from the connector on the system board.
Installing the coin-cell battery Steps 1. With the positive-side facing up, insert the coin-cell battery into the battery socket on the I/O board [1]. 2. Press the battery until it clicks into place [2].
Next steps 1. 2. 3. 4. 5. Connect the battery cable to the connector on the system board. Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer kõvaketas Removing the hard drive assembly Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive assembly Remove the base cover Remove the battery Steps 1.
4. Disconnect the interposer from the hard drive. 5. Remove the four (M3x3) screws that secure the hard drive bracket to the hard drive [1]. 6. Lift the hard drive bracket off the hard drive [2].
Installing the hard drive assembly Steps 1. Align the screw holes on the hard drive bracket with the screw holes on the hard drive [1]. 2. Replace the four (M3x3) screws that secure the hard drive bracket to the hard drive [2]. 3. Connect the interposer to the hard drive.
4. Align the screw holes on the hard drive assembly with the screw holes on the palmrest and keyboard assembly [1]. 5. Replace the four (M2x3) screws that secure the hard drive assembly to the palmrest and keyboard assembly [2]. 6. Connect the hard drive cable to the system board and close the latch to secure the cable [3]. Next steps 1. 2. 3. 4. 5.
Süsteemi ventilaator Removing the system fan Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive assembly Remove the base cover Disconnect the battery cable from the connector on the system board. Steps 1. Disconnect the ODD cable, display cable and fan cable from the system board [1, 2, 3]. 2. Remove the three (M2.5x5) screws that secure the fan to the palmrest and keyboard board assembly [1]. 3.
Installing the system fan Steps 1. Align the screw holes on the fan with the screw holes on the palm rest and keyboard board assembly [1]. 2. Replace the three (M2.5x5) screws that secure the fan to the palm rest and keyboard board assembly [2].
3. Route the display cable through the routing guides on the fan [1]. 4. Connect the ODD cable, display cable and fan cable to the system board [3,2,1].
Next steps 1. 2. 3. 4. 5. Replace the battery Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Jahutusradiaator Removing the heatsink Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer Remove the SD memory card Remove the base cover Remove the battery Remove the system fan Steps 1. Loosen the four captive screws that secure the heatsink to the system board [1].
Installing the heatsink Steps 1. Place the heatsink on the system board and align the screw holes on the heatsink with the screw holes on the system board [1]. 2. In sequential order (as indicated on the heatsink), tighten the four captive screws that secure the heatsink to the system board [2]. Next steps 1. 2. 3. 4. 5. Connect the battery cable to the connector on the system board.
Installing the heatsink Steps 1. Place the heatsink on the system board and align the screw holes on the heatsink with the screw holes on the system board [1]. 2. Replace the three (M2x3) screws that secure the heatsink to the system board [2]. 3. In sequential order (as indicated on the heatsink), tighten the four captive screws that secure the heatsink to the system board [3].
Next steps 1. 2. 3. 4. 5. Connect the battery cable to the connector on the system board. Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Kõlarid Removing the speakers Prerequisites 1. 2. 3. 4. 5. 6. Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive assembly Remove the base cover Remove the battery Remove the SSD Steps 1.
Installing the speakers About this task NOTE: If the rubber grommets are pushed out when removing the speakers, push them back in before replacing the speakers. Steps 1. Using the alignment posts and rubber grommets, place the speakers in the slots on the palm rest and keyboard assembly [1]. 2. Route the speaker cable through the routing guides on the palm rest and keyboard assembly [2]. 3. Connect the speaker cable to the connector on the system board [3].
Next steps 1. 2. 3. 4. 5. 6. Replace the SSD Replace the battery Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer S-/V-paneel Removing the IO board Prerequisites 1. 2. 3. 4. 5. 6. Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive assembly Remove the base cover Remove the battery Remove the hard drive assembly Steps 1.
3. Remove the single (M2x4) screw that secures the I/O board to the palm rest and keyboard assembly [1]. 4. Lift the I/O board, along with the cable, off the palm rest and keyboard assembly [2]. NOTE: When the IO board cable is disconnected from the system board, an RTC error occurs. This error occurs whenever the RTC/coin-cell battery, IO board, or system board are removed.
An "Invalid Configuration" error message is displayed prompting you to enter the BIOS and configure the date and time. The computer starts functioning normally after setting the date and time. Installing the IO board Steps 1. Using the alignment posts, place the I/O board on the palm rest and keyboard assembly [1]. 2. Replace the single (M2x4) screw that secures the I/O board to the palm rest and keyboard assembly [2]. 3. Connect the VGA cable to the I/O board [1]. 4.
Next steps 1. 2. 3. 4. 5. 6. Replace the hard drive assembly Replace the battery Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Puuteplaat Removing the touch pad assembly Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive assembly Remove the base cover Remove the battery Steps 1.
3. Remove the two (M2x2) screws that secure the touch pad bracket to the palmrest and keyboard assembly [1]. 4. Lift the touch pad bracket off the palm rest and keyboard assembly [2]. 5. Remove the four (M2x2) screws that secure the touch pad to the palmrest and keyboard assembly [1]. 6. Lift the touch pad off the palmrest and keyboard assembly [2].
Installing the touch pad assembly About this task NOTE: Ensure that the touch pad is aligned with the guides available on the palm-rest and keyboard assembly, and the gap on either sides of the touch pad is equal. Steps 1. Place the touch pad into the slot on the palmrest and keyboard assembly [1]. 2. Replace the four (M2x2) screws that secure the touch pad to the palmrest and keyboard assembly [2].
3. Place the touch pad bracket into the slot on the palmrest and keyboard assembly [1]. 4. Replace the two screws (M2x2) that secure the touch pad bracket to the palmrest and keyboard assembly [2]. 5. Affix the tape that secures the touch pad to the palmrest and keyboard assembly [1]. 6. Slide the touch pad cable and hard drive cable into its connector on the system board and close the latch to secure the cables [2, 3].
Next steps 1. 2. 3. 4. 5. Replace the battery Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Ekraanisõlm Removing the display assembly Prerequisites 1. 2. 3. 4. 5. 6. Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive assembly Remove the base cover Disconnect the battery cable from the connector on the system board Remove the WLAN Steps 1.
4. Remove the five (M2.5x5) screws that secure the left and right hinges to the system board, and palmrest and keyboard assembly [1]. 5. Lift the hinges [1]. Lift the palmrest and keyboard assembly at an angle [2]. 6. Lift the hinges.
7. After performing all the preceding steps, you are left with display assembly.
Installing the display assembly About this task NOTE: Ensure that the hinges are opened to the maximum before replacing the display assembly on the palmrest and keyboard assembly. Steps 1. Align and place the palmrest and keyboard assembly under the hinges on the display assembly [1]. 2. Seat the palmrest and keyboard assembly on the display assembly [2]. 3. Press the hinges down on the system board, and palmrest and keyboard assembly [3]. 4. Replace the five (M2.
5. Route the display cable through the routing guides on the palmrest and keyboard assembly [1]. 6. Adhere the antenna cables to the system board [2]. 7. Connect the display cable and the optical drive cable to the connector on the system board [3, 4].
Next steps 1. 2. 3. 4. 5. Replace the WLAN Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Ekraani raam Removing the display bezel Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer Remove the SD memory card Remove the optical drive assembly Remove the base cover Remove the display assembly Steps 1. Pry the inner top side of the display bezel [1]. 2.
Next steps 1. 2. 3. 4. 5. 6. 7. Replace the display assembly Replace the hard drive assembly Connect the battery cable to the connector on the system board. Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Toitenupu paneel Removing the power button board Prerequisites 1. 2. 3. 4. 5. 6. 7. 8.
4. Lift the power button board, along with the cable off the palmrest and keyboard assembly [4]. Installing the power button board Steps 1. Place the power-button board into the slot on the palmrest and keyboard assembly [1]. 2. Replace the single (M2x2) screw that secures the power button board to the palmrest and keyboard assembly [2]. 3. Adhere the conductive tape to the power button board [3]. 4. Slide the power button cable to the system board and close the latch to secure the cable [4].
Next steps 1. 2. 3. 4. 5. 6. 7. 8. Replace the display assembly Replace the system fan Replace the WLAN Connect the battery cable to the connector on the system board. Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Emaplaat Removing the system board Prerequisites 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
Steps 1. Disconnect the following cables from the system board: a) b) c) d) e) f) Power adapter port cable [1]. Power cable [2]. IO board cable [3]. Touchpad cable [4]. Keyboard cable [5]. Speaker cable [6]. 2. Remove the single (M2x4) screw that secures the system board to the palmrest and keyboard assembly [1]. 3. Lift the system board off the palmrest and keyboard assembly [2].
Installing the system board Steps 1. Align the screw hole on the system board with the screw hole on the palmrest and keyboard assembly [1]. 2. Replace the single (M2x4) screw that secures the system board to the palmrest and keyboard assembly [2].
3. Connect the following cables to the system board: a) b) c) d) e) f) Speaker cable [1]. Keyboard cable [2]. Touchpad cable [3]. IO board cable [4]. Power cable [5]. Power adapter port cable [6].
Next steps 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Replace the power button board Replace the display assembly Replace the heatsink Replace the system fan Replace the hard drive assembly Replace the SSD Replace the WLAN Replace the battery Replace the base cover Replace the SD memory card Follow the procedure in after working inside your computer Toiteadapteri pesa Removing the power adapter port Prerequisites 1. 2. 3. 4. 5.
6. 7. 8. 9. Remove the WLAN Remove the SSD Remove the display assembly Remove the power button board Steps 1. Disconnect and route the power adapter cable from the system board [1, 2]. 2. Remove the single (M2x3) screw that secures the power adapter port to the palmrest and keyboard assembly [3]. 3. Lift the power adapter port, along with its cable, off the palmrest and keyboard assembly [4]. Installing the power adapter port Steps 1.
Next steps 1. 2. 3. 4. 5. 6. 7. 8. 9. Replace the power button board Replace the display assembly Replace the SSD Replace the WLAN Replace the battery Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Kaamera Removing the camera Prerequisites 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Steps 1. Using a plastic scribe, gently pry the camera off the display back-cover and antenna assembly [1]. 2. Disconnect the camera cable from the camera module [2]. 3. Lift the camera module from the display back-cover and antenna assembly [3]. Installing the camera Steps 1. Connect the camera cable to the camera module [1]. 2. Using the alignment post, adhere the camera module on the display back-cover and antenna assembly [2]. 3. Route the camera cable through the routing channels [3].
Next steps 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Replace the display bezel Replace the display assembly Replace the hard drive assembly Replace the system fan Replace the heatsink Replace the SSD Replace the WLAN Replace the battery Replace the base cover Replace the SD memory card Follow the procedure in after working inside your computer Ekraanipaneel Removing the display panel Prerequisites 1. 2. 3. 4. 5. 6. 7.
8. 9. 10. 11. 12. 13. Remove the hard drive assembly Remove the system fan Remove the heatsink Remove the display assembly Remove the display bezel Remove the camera Steps 1. Remove the four (M2x2) screws that secure the display panel to the display back-cover and antenna assembly [1]. 2. Lift the display panel and turn it over [2]. 3. Peel the tape that secures the display cable to the back of the display panel [1]. 4.
Installation display panel Steps 1. Place the display panel on a flat and clean surface [1]. 2. Connect the display cable to the connector at the back of the display panel and close the latch to secure the cable [2]. 3. Adhere the tape that secures the display cable to the back of the display panel [3]. 4. Turn the display panel over and place it on the display back-cover and antenna assembly [4].
5. Align the screw holes on the display panel with the screw holes on the display back-cover and antenna assembly. 6. Replace the four (M2x2) screws that secure the display panel to the display back-cover and antenna assembly [1].
Next steps 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Replace the camera Replace the display bezel Replace the display assembly Replace the hard drive assembly Replace the system fan Replace the heatsink Replace the SSD Replace the WLAN Replace the battery Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Ekraani hinged Removing the display hinges Prerequisites 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
Installing the display hinges Steps 1. Align the screw holes on the hinges and brackets with the screw holes on the display back-cover and antenna assembly [1]. 2. Replace the eight (M2.5x2.5) screws and two (M2x2) screws that secure the hinges to the display back-cover and antenna assembly [3,2 ].
Next steps 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Replace the display panel Replace the camera Replace the display bezel Replace the display assembly Replace the hard drive assembly Replace the system fan Replace the heatsink Replace the SSD Replace the WLAN Replace the battery Replace the base cover Replace the optical drive assembly Replace the SD memory card Follow the procedure in after working inside your computer Ekraanikaabel Removing the display cable Prerequisites 1. 2. 3. 4.
5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Remove the battery Remove the WLAN Remove the SSD Remove the hard drive assembly Remove the system fan Remove the heatsink Remove the display assembly Remove the display bezel Remove the display panel Remove the display hinges Steps 1. Disconnect the camera cable on the display back-cover and antenna assembly [1]. 2. Peel the adhesive that secures the camera cable [2]. 3.
Next steps 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Remove the WLAN Remove the SSD Remove the hard drive assembly Remove the system fan Remove the heatsink Remove the display assembly Remove the display bezel Remove the camera Remove the display panel Remove the display hinges Remove the display cable About this task After performing all the preceding steps, you are left with the display back-cover.
Installing the display back-cover About this task Place the display back-cover on a clean and flat surface. Next steps 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
Randmetoe ja klaviatuurisõlm Removing the palmrest and keyboard assembly Prerequisites 1. Follow the procedure in before working inside your computer 2. Remove the SD memory card 3. Remove the optical drive assembly 4. Remove the base cover 5. Remove the battery 6. Remove the memory 7. Remove the WLAN 8. Remove the SSD 9. Remove the speakers 10. Remove the coin-cell battery 11. Remove the hard drive assembly 12. Remove the system fan 13. Remove the heatsink 14. Remove the IO board 15.
Komponentide eemaldamine ja paigaldamine
3 Süsteemi seadistus System setup (Süsteemi seadistus) võimaldab hallata riistvara ja teha seadistusi BIOS-i tasemel. System setup (Süsteemi seadistus) võimaldab teil: • • • • • muuta pärast riistvara lisamist või eemaldamist NVRAM-i sätteid; vaadata süsteemi riistvara konfiguratsiooni; lubada või keelata integreeritud seadmeid; määrata jõudluse ja energiahalduse lävesid; hallata arvuti turbesätteid.
Süsteemi seadistusvalikud MÄRKUS: Olenevalt ja paigaldatud seadmetest võidakse selles jaotises loetletud üksused kuvada või mitte. Üldised valikud Tabel 2. Üldine Valik Kirjeldus Süsteemiandmed Kuvab järgmised andmed. • • • • Süsteemi andmed: kuvatakse BIOS-i versioon, seerianumber, inventari tähise number, omanikusilt, ostukuupäev, valmistamise kuupäev ja kiirhoolduse kood.
Valik Kirjeldus Draivid Võimaldab lubada või keelata mitmesugused integreeritud kettad: • • • • SATA-0 (vaikimisi lubatud) SATA-1 (vaikimisi lubatud) SATA-2 (vaikimisi lubatud) M.2 PCIe SSD-0 (vaikesäte) Nutikas aruandlus See väli juhib, kas integreeritud ketaste puhul teatatakse kõvaketta vigadest süsteemi käivitamisel. Valik Enable Smart Reporting option (Luba nutika aruandluse valik) on vaikimisi keelatud.
Valik Kirjeldus Parooli muutmine See valik võimaldab määrata, kas süsteemi ja kõvaketta paroolide muudatused on lubatud, kui määratakse administraatori parool. Allow Non-Admin Password Changes (Luba mitte-administraatori parooli muutmine) – see on vaikimisi lubatud. Mitte-administraatori häälestuse muudatused Määrab, kas häälestusvalikute muutmine on lubatud, kui on määratud administraatori parool.
Valik Kirjeldus • • Ekspert-võtmehaldus Kasutatav režiim (vaikimisi) Auditirežiim Võimaldab käsitseda turvavõtmete andmebaase ainult juhul, kui süsteem on kohandatud režiimis. Valik Enable Custom Mode (Luba kohandatud režiim) on vaikimisi keelatud. Valikud on järgmised: • • • • PK (vaikesäte) KEK db dbx Kui aktiveerite režiimi Custom Mode (Kohandatud režiim), kuvatakse vastavad valikud PK, KEK, db ja dbx.
Valik Kirjeldus • Luba Intel SpeedStep See valik on vaikimisi määratud. C-States Control Võimaldab lubada või keelata protsessori täiendavad uneolekud. • C-olekud See valik on vaikimisi määratud. Intel TurboBoost Võimaldab lubada või keelata protsessori režiimi Intel TurboBoost. • Luba Intel TurboBoost See valik on vaikimisi määratud. Hyper-Thread Control Võimaldab lubada või keelata protsessori HyperThreading režiimi.
Valik Kirjeldus Peamine aku laadimise konfigureerimine Võimaldab valida aku jaoks laadimisrežiimi. Valikud on järgmised. • • • • • Kohandatud – vaikimisi lubatud Standardne – laeb aku täis standardkiirusel. Kiirlaadimine – aku laeb lühema aja jooksul, kasutades Delli kiirlaadimistehnoloogiat. Peamiselt AC kasutamine Kohandatud Kui on valitud kohandatud laadimine, saate konfigureerida ka kohandatud laadimise alustamise ja kohandatud laadimise lõpetamise.
Valik Kirjeldus Enable Intel Virtualization Technology (Luba Inteli virtualiseerimistehnoloogia) – vaikimisi lubatud. VT Direct I/O jaoks Lubab või keelab virtuaalse seadmemonitori (VMM) puhul riistvara lisavõimaluste kasutamise, mida pakub Intel®-i virtualiseerimistehnoloogia Direct I/O jaoks. Enable VT for Direct I/O (Luba VT otsese I/O jaoks) – vaikimisi lubatud.
Süsteemi logid Valik Kirjeldus BIOS-i sündmused Võimaldab kuvada ja kustutada süsteemi seadistuse (BIOS) POST sündmusi. Thermal Events Võimaldab kuvada ja kustutada süsteemi seadistuse (temperatuur) sündmusi. Power Events Võimaldab kuvada ja kustutada süsteemi seadistuse (toide) sündmusi. SupportAssist Süsteemi resolutsioon Valik Kirjeldus Operatsioonisüste Võimaldab teil juhtida süsteemi SupportAssist System automaatse algkäivituse voogu.
• • • • Paroolis võib olla kuni 32 märki. Parool võib sisaldada numbreid 0–9. Sobivad ainult väiketähed, suurtähed pole lubatud. Lubatud on ainult järgmised erimärgid: tühik, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`). 3. Tippige väljale Confirm new password (Kinnitage uus parool) varem sisestatud süsteemi parool ja klõpsake nuppu OK. 4. Vajutage klahvi Esc ja kuvatakse teade, mis ütleb, et salvestaksite muudatused. 5. Muudatuste salvestamiseks vajutage klahvi Y. Arvuti taaskäivitub.
4 Tõrkeotsing Täiustatud algkäivituseelse süsteemi hindamise (ePSA) diagnostika See ülesanne ePSA diagnostika (nimetatakse ka süsteemidiagnostikaks) teeb teie riistvara täieliku kontrollimise. ePSA on manustatud BIOS-i ja BIOS käivitab selle sisemiselt. Manustatud süsteemidiagnostika annab valikud konkreetsete seadmete või seadmegruppide jaoks, võimaldades teha järgmist.
Näiteks vilgub toite ja aku oleku märgutuli merekollaselt kaks korda, millele järgneb paus ja seejärel vilgub valgelt kolm korda, millele järgneb paus. Muster 2,3 jätkub arvuti väljalülitamiseni ja näitab, et mälu või RAM-i ei tuvastatud. Järgmine tabel kuvab toite ja aku oleku märgutule mustreid ning seotud probleeme. Tabel 9.
Sammud 1. Lülitage arvuti sisse. 2. 1. Avage aadress www.dell.com/support. 3. Klõpsake linki Product Support (Tugiteenused), sisestage oma arvuti hooldussilt ja klõpsake nuppu Submit (Edasta). MÄRKUS: Kui teil pole hooldussilti, kasutage automaattuvastuse funktsiooni või otsige loendist üles arvuti mudel. 4. Klõpsake linki Drivers & downloads > Find it myself (Draiverid ja allalaadimised > Leian selle ise). 5. Valige arvutisse installitud operatsioonisüsteem. 6.
5 Abi saamine Teemad: • Delli kontaktteave Delli kontaktteave Eeltingimused MÄRKUS: Kui teil pole aktiivset Interneti-ühendust, võite leida kontaktteavet oma ostuarvelt, saatelehelt, tšekilt või Delli tootekataloogist. See ülesanne Dell pakub mitut veebi- ja telefonipõhist toe- ning teenindusvõimalust. Saadavus võib riigi ja toote järgi erineda ning mõned teenused ei pruugi olla teie piirkonnas saadaval. Delliga müügi, tehnilise toe või klienditeeninduse küsimustes ühenduse võtmiseks: Sammud 1.