Dell Vostro 5391 Instrukcja serwisowa Model regulacji: P114G Typ regulacji: P114G001
Uwagi, przestrogi i ostrzeżenia UWAGA Napis UWAGA oznacza ważną wiadomość, która pomoże lepiej wykorzystać komputer. OSTRZEŻENIE Napis PRZESTROGA informuje o sytuacjach, w których występuje ryzyko uszkodzenia sprzętu lub utraty danych, i przedstawia sposoby uniknięcia problemu. PRZESTROGA Napis OSTRZEŻENIE informuje o sytuacjach, w których występuje ryzyko uszkodzenia sprzętu, obrażeń ciała lub śmierci. © 2018–2019 Dell Inc. lub podmioty zależne. Wszelkie prawa zastrzeżone.
Spis treści 1 Serwisowanie komputera...............................................................................................................6 Instrukcje dotyczące bezpieczeństwa................................................................................................................................ 6 Przed przystąpieniem do serwisowania komputera..........................................................................................................
Wymontowywanie zestawu wyświetlacza................................................................................................................. 33 Instalowanie zestawu wyświetlacza............................................................................................................................36 Złącze zasilacza...................................................................................................................................................................
Zarządzanie energią.......................................................................................................................................................70 POST Behavior (Zachowanie podczas testu POST).................................................................................................71 Virtualization Support (Obsługa wirtualizacji).............................................................................................................
1 Serwisowanie komputera Instrukcje dotyczące bezpieczeństwa Aby uchronić komputer przed uszkodzeniem i zapewnić sobie bezpieczeństwo, należy przestrzegać następujących zaleceń dotyczących bezpieczeństwa. O ile nie wskazano inaczej, każda procedura opisana w tym dokumencie opiera się na założeniu, że są spełnione następujące warunki: • • Użytkownik zapoznał się z informacjami dotyczącymi bezpieczeństwa, jakie zostały dostarczone z komputerem.
Przed przystąpieniem do serwisowania komputera UWAGA W zależności od zamówionej konfiguracji posiadany komputer może wyglądać nieco inaczej niż na ilustracjach w tym dokumencie. Zabezpieczenie przed wyładowaniem elektrostatycznym Wyładowania elektrostatyczne (ESD) to główny problem podczas korzystania z podzespołów elektronicznych, a zwłaszcza wrażliwych komponentów, takich jak karty rozszerzeń, procesory, moduły DIMM pamięci i płyty systemowe.
• • • • • podczas normalnego użytkowania. Należy je regularnie sprawdzać za pomocą testera, aby uniknąć przypadkowego uszkodzenia sprzętu przez wyładowania elektrostatyczne. Zaleca się testowanie paska na nadgarstek i przewodu łączącego co najmniej raz w tygodniu. Tester paska antystatycznego na nadgarstek — przewody wewnątrz paska są podatne na uszkodzenia.
4. Podłącz komputer i wszystkie urządzenia peryferyjne do gniazdek elektrycznych. 5. Włącz komputer.
2 Wymontowywanie i instalowanie komponentów Zalecane narzędzia Procedury przedstawione w tym dokumencie wymagają użycia następujących narzędzi: • • • • • Wkrętak krzyżakowy nr 0 Wkrętak krzyżakowy nr 1 Śrubokręt Phillips nr 2 Rysik z tworzywa sztucznego Wkrętak Torx T-30 UWAGA Wkrętak nr 0 jest przeznaczony do śrub 0–1, a wkrętak nr 1 do śrub 2–4. Wykaz śrub UWAGA Przy wykręcaniu śrub z elementów zalecane jest, aby zanotować typ oraz liczbę śrub, a następnie umieścić je w pudełku na śruby.
Element do czego mocowany zestaw dysku twardego zestaw podparcia dłoni i M2x3 klawiatury 4 wspornik dysku twardego Dysk twardy M3x3 4 Radiator Płyta systemowa M2x3 3 Zawiasy zestaw podparcia dłoni i M2,5x5 klawiatury 5 Wsporniki zawiasu zestaw pokrywy wyświetlacza i anteny M2,5x4 8 Wsporniki zawiasu zestaw pokrywy wyświetlacza i anteny M2x2 2 Karta we/wy Typ śruby Ilość zestaw podparcia dłoni i M2x4 klawiatury Wspornik napędu dysków optycznych (dotyczy tylko Napęd dysków komputer
Element do czego mocowany Typ śruby Tabliczka dotykowa zestaw podparcia dłoni i M2x2 klawiatury 4 wspornik karty sieci bezprzewodowej Płyta systemowa 1 M2x3 Ilość pokrywa dolna Wymontowywanie pokrywy dolnej 1. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Na ilustracji przedstawiono umiejscowienie i procedurę wymontowywania pokrywy dolnej.
1. Poluzuj trzy śruby mocujące pokrywę dolną. 2. Wykręć cztery śruby (M2x6) mocujące pokrywę dolną do zestawu podparcia dłoni i klawiatury. 3. Rysikiem z tworzywa sztucznego podważ pokrywę dolną, aby ją uwolnić z zestawu podparcia dłoni i klawiatury. 4. Zdejmij pokrywę dolną z zestawu podparcia dłoni i klawiatury. Instalowanie pokrywy dolnej W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element.
1. Ustaw komputer tak, aby zawiasy były skierowane w Twoją stronę. 2. Umieść pokrywę dolną na zestawie podparcia dłoni i klawiatury, a następnie wciśnij pokrywę dolną na swoje miejsce. 3. Wkręć cztery śruby (M2x6) mocujące pokrywę dolną do zestawu podparcia dłoni i klawiatury. 4. Dokręć trzy śruby osadzone mocujące pokrywę dolną do zestawu podparcia dłoni i klawiatury. 1. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Akumulator Wymontowywanie akumulatora 1.
1. Odłącz kabel akumulatora od płyty systemowej. 2. Wykręć dwie śruby (M2x2) mocujące akumulator do zestawu podparcia dłoni i klawiatury. 3. Wykręć śrubę (M1,6x4) mocującą akumulator do płyty systemowej oraz zestawu podparcia dłoni i klawiatury. 4. Wyjmij akumulator z zestawu podparcia dłoni i klawiatury. Instalowanie akumulatora W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element.
1. Podłącz kabel akumulatora do płyty systemowej. 2. Wkręć dwie śruby (M2x2) mocujące akumulator do zestawu podparcia dłoni i klawiatury. 3. Wkręć śrubę (M1,6x4) mocującą akumulator do płyty systemowej oraz zestawu podparcia dłoni i klawiatury. 1. Zainstaluj pokrywę dolną. 2. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Bateria pastylkowa Wymontowywanie baterii pastylkowej 1. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera.
1. Odłącz kabel baterii pastylkowej od płyty systemowej. 2. Wyjmij kabel baterii pastylkowej z prowadnicy. 3. Odłącz baterię pastylkową od zestawu podparcia dłoni i klawiatury. Instalowanie baterii pastylkowej W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Na ilustracji przedstawiono umiejscowienie i procedurę instalacji baterii pastylkowej. 1. Przymocuj baterię pastylkową do gniazda w zestawie podparcia dłoni i klawiatury. 2.
3. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Dysk SSD Wymontowywanie dysku SSD M.2 2280 1. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. 2. Wymontuj pokrywę dolną. 3. Wymontuj akumulator. Na ilustracji przedstawiono umiejscowienie i procedurę wymontowywania dysku SSD. 1. Odklej taśmę mocującą radiator do płyty systemowej. 2. Wykręć śrubę (M2x2,5) mocującą dysk SSD do płyty systemowej. 3.
Na ilustracji przedstawiono umiejscowienie i procedurę instalacji dysku SSD. 1. Dopasuj wycięcie na dysku SSD do zaczepu w gnieździe dysku SSD, a następnie wsuń dysk SSD do gniazda dysku SSD. 2. Wkręć śrubę (M2x2,5) mocującą dysk SSD do płyty systemowej. 3. Przyklej taśmę z tworzywa sztucznego mocującą radiator do płyty systemowej. 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Wymontowywanie dysku SSD M.2 2230 1.
1. Odklej taśmę mocującą radiator do płyty systemowej. 2. Wykręć śrubę (M2x2,5) mocującą wspornik dysku SSD do płyty systemowej. 3. Przesuń i wyjmij wspornik dysku SSD z gniazda na płycie systemowej. 4. Przesuń i wyjmij moduł dysku SSD z gniazda na płycie systemowej. Instalowanie dysku SSD M.2 2230 W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Na ilustracji przedstawiono umiejscowienie i procedurę instalacji dysku SSD.
1. Dopasuj wycięcie na dysku SSD do zaczepu w gnieździe dysku SSD, a następnie wsuń dysk SSD do gniazda dysku SSD. 2. Wsuń wspornik dysku SSD na kartę SSD na płycie systemowej. 3. Wkręć śrubę (M2x2,5) mocującą dysk SSD do płyty systemowej. 4. Przyklej taśmę z tworzywa sztucznego mocującą radiator do płyty systemowej. 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Radiator Wymontowywanie radiatora 1.
1. Odklej taśmę mocującą radiator do płyty systemowej. 2. W kolejności odwrotnej do wskazanej na radiatorze (7>6>5>4>3>2>1) poluzuj siedem śrub mocujących radiator do płyty systemowej. 3. Zdejmij radiator z płyty systemowej. Instalowanie radiatora W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element.
Na ilustracji przedstawiono umiejscowienie i procedurę instalacji pokrywy dolnej. 1. Dopasuj otwory na śruby w radiatorze do otworów w płycie systemowej. 2. W kolejności wskazanej na radiatorze dokręć siedem śrub osadzonych mocujących radiator do płyty systemowej. 3. Przyklej taśmę z tworzywa sztucznego mocującą radiator do płyty systemowej. 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera.
1. Odłącz kabel płyty I/O od płyty systemowej i płyty I/O. UWAGA Ten krok ma zastosowanie tylko w przypadku komputerów wyposażonych w kartę sieci WWAN. 2. Wkręć dwie śruby (M2x3) mocujące wentylator do płyty systemowej. 3. Lekko unieś wentylator z zestawu podparcia dłoni i klawiatury. 4. Odłącz kabel wentylatora od płyty systemowej i całkowicie zdejmij wentylator z zestawu podparcia dłoni i klawiatury.
1. Podłącz kabel wentylatora do złącza na płycie systemowej. 2. Dopasuj otwory na śruby wentylatora do otworów w zestawie podparcia dłoni i klawiatury. 3. Wkręć dwie śruby (M2x3) mocujące wentylator do zestawu podparcia dłoni i klawiatury. 4. Podłącz kabel płyty I/O do płyty systemowej i płyty I/O. UWAGA Ten krok ma zastosowanie tylko w przypadku komputerów wyposażonych w kartę sieci WWAN. 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3.
1. Otwórz zatrzask i odłącz kabel tabliczki dotykowej od płyty systemowej. 2. Odłącz kabel głośnika od płyty systemowej. 3. Odlep taśmy mocujące kabel głośników do zestawu podparcia dłoni i klawiatury. 4. Zapamiętaj sposób poprowadzenia kabla głośników i wyjmij kabel z prowadnic w zestawie podparcia dłoni i klawiatury. UWAGA Przed wyjęciem głośników należy zwrócić uwagę na położenie gumowych pierścieni. 5. Wyjmij głośniki razem z kablem z zestawu podparcia dłoni i klawiatury.
1. Umieść głośniki w gniazdach w zestawie podparcia dłoni i klawiatury, dopasowując je do wypustek i gumowych krążków. 2. Umieść kabel głośników w prowadnicach w zestawie podparcia dłoni i klawiatury. 3. Przyklej taśmy mocujące kabel głośników do zestawu podparcia dłoni i klawiatury. 4. Podłącz kabel głośników do płyty systemowej. 5. Podłącz kabel tabliczki dotykowej do płyty systemowej i zamknij zatrzask, aby zamocować kabel. 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3.
Na ilustracji przedstawiono umiejscowienie i procedurę wymontowywania karty sieci WLAN. 1. Odklej taśmę mocującą radiator do płyty systemowej. 2. Wykręć śrubę (M2x2,5) mocującą wspornik karty sieci WLAN do karty, a następnie zdejmij wspornik z karty sieci WLAN. 3. Odłącz kable antenowe od karty WLAN. 4. Przesuń i wyjmij kartę sieci WLAN z gniazda. Instalowanie karty sieci WLAN W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element.
1. Podłącz kable antenowe do karty sieci WLAN. 2. Dopasuj wycięcie na karcie sieci WLAN do wypustki w gnieździe karty sieci WLAN i wsuń kartę do gniazda pod kątem. 3. Wyrównaj wspornik karty sieci WLAN i załóż go na kartę. 4. Wkręć śrubę (M2x2,5) mocującą wspornik karty sieci WLAN do karty sieci WLAN. 5. Przyklej taśmę mocującą radiator do płyty systemowej. 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera.
Na ilustracji przedstawiono umiejscowienie i procedurę wymontowywania karty sieci WWAN. 1. Wykręć śrubę (M2x2,5) mocującą wspornik karty sieci WWAN do karty. 2. Przed zdjęciem wspornika karty sieci WWAN z karty zwróć uwagę na jego wyrównanie. 3. Odłącz kable antenowe od karty sieci WWAN. 4. Przesuń i wyjmij kartę sieci WWAN z gniazda. Instalowanie karty sieci WWAN UWAGA Ta procedura ma zastosowanie tylko w przypadku komputerów wyposażonych w kartę sieci WWAN.
1. Dopasuj wycięcie na karcie sieci WWAN do wypustki w gnieździe karty sieci WWAN i wsuń kartę do gniazda pod kątem. 2. Podłącz kable antenowe do karty sieci WWAN i umieść wspornik karty sieci WWAN na samej karcie. 3. Wkręć jedną śrubę (M2x2,5) mocującą wspornik karty WWAN do samej karty. 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Tabliczka dotykowa Wymontowywanie tabliczki dotykowej 1.
1. Odklej taśmy mocujące tabliczkę dotykową do zestawu podparcia dłoni i klawiatury. 2. Otwórz zatrzask i odłącz kabel tabliczki dotykowej od płyty systemowej. 3. Wykręć trzy śruby (M1,6x2) mocujące wspornik tabliczki dotykowej do zestawu podparcia dłoni i klawiatury. 4. Zdejmij wspornik tabliczki dotykowej z zestawu podparcia dłoni i klawiatury. 5. Wykręć dwie śruby (M1,6x2) mocujące tabliczkę dotykową do zestawu podparcia dłoni i klawiatury. 6.
1. Umieść tabliczkę dotykową we wnęce w zestawie podparcia dłoni i klawiatury. 2. Wkręć dwie śruby (M1,6x2) mocujące tabliczkę dotykową do zestawu podparcia dłoni i klawiatury. 3. Umieść wspornik tabliczki dotykowej w gnieździe w zestawie podparcia dłoni i klawiatury. 4. Wkręć trzy śruby (M1,6x2) mocujące wspornik tabliczki dotykowej do zestawu podparcia dłoni i klawiatury. 5. Podłącz kabel tabliczki dotykowej do złącza na płycie systemowej i zamknij zatrzask, aby zamocować kabel. 6.
Wymontowywanie i instalowanie komponentów
1. Wykręć dwie śruby (M2x4) mocujące zawiasy wyświetlacza do karty I/O oraz zestawu podparcia dłoni i klawiatury. 2. Odklej taśmę i przy użyciu uchwytu odłącz kabel wyświetlacza od płyty systemowej. 3. Otwórz zestaw wyświetlacza możliwie jak najszerzej. 4. Zdejmij zestaw podparcia dłoni i klawiatury z zestawu wyświetlacza.
Instalowanie zestawu wyświetlacza W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Na ilustracji przedstawiono umiejscowienie i procedurę instalacji zestawu wyświetlacza.
1. Wyrównaj i umieść zestaw podparcia dłoni i klawiatury w zestawie wyświetlacza. 2. Zamknij zawiasy wyświetlacza, korzystając z wypustek. 3. Wkręć dwie śruby (M2x4) mocujące lewy i prawy zawias wyświetlacza do karty I/O oraz zestawu podparcia dłoni i klawiatury. 4. Podłącz kabel wyświetlacza do płyty systemowej i przyklej taśmę mocującą kabel wyświetlacza do płyty systemowej. 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3.
1. Odłącz kabel gniazda zasilacza od płyty systemowej. 2. Wykręć śrubę (M2x3) mocującą gniazdo zasilacza do zestawu podparcia dłoni i klawiatury. 3. Wyjmij gniazdo zasilacza razem z kablem z zestawu podparcia dłoni i klawiatury. Instalowanie gniazda zasilacza W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Na ilustracji przedstawiono umiejscowienie i procedurę instalacji gniazda zasilacza.
1. Podłącz kabel gniazda zasilacza do płyty systemowej. 2. Wkręć śrubę (M2x3) mocującą gniazdo zasilacza do zestawu podparcia dłoni i klawiatury. 3. Wyrównaj i umieść wspornik kabla wyświetlacza na płycie systemowej. 4. Wkręć śrubę (M2,5x3,5) mocującą wspornik kabla wyświetlacza do płyty systemowej. 5. Zamknij zawiasy wyświetlacza, korzystając z wypustek. 6. Wkręć śrubę (M2x4) mocującą prawy zawias wyświetlacza do płyty systemowej. 1. 2. 3. 4. 5. Zainstaluj zestaw wyświetlacza. Zainstaluj kartę sieci WLAN.
1. Wykręć śrubę (M2x4) mocującą lewy zawias wyświetlacza do zestawu podparcia dłoni i klawiatury. 2. Odchyl zawiasy wyświetlacza o 90 stopni. 3. Odklej taśmę mocującą kartę I/O do zestawu podparcia dłoni i klawiatury. 4. Zdejmij taśmę mocującą kabel płyty we/wy do płyty we/wy. 5. Otwórz zatrzask i odłącz kabel płyty we/wy od płyty we/wy. 6. Wykręć śrubę (M2,5x2,5) mocującą kartę I/O do zestawu podparcia dłoni i klawiatury. 7. Wykręć śrubę (M2x3) mocującą kartę I/O do zestawu podparcia dłoni i klawiatury. 8.
1. Wyrównaj i umieść kartę I/O w zestawie podparcia dłoni i klawiatury. 2. Wkręć śrubę (M2x3) mocującą kartę I/O do zestawu podparcia dłoni i klawiatury. 3. Wkręć śrubę (M2,5x2,5) mocującą kartę I/O do zestawu podparcia dłoni i klawiatury. 4. Podłącz kabel płyty I/O do płyty I/O i zamknij zatrzask, aby zamocować kabel. 5. Przyklej taśmę mocującą do karty I/O. 6. Przyklej taśmę mocującą kartę I/O do zestawu podparcia dłoni i klawiatury. 7. Zamknij zawiasy wyświetlacza, korzystając z wypustek. 8.
2. 3. 4. 5. 6. Wymontuj pokrywę dolną. Wymontuj akumulator. Wymontuj kartę sieci WLAN. Wymontuj wentylator. Wymontuj płytę we/wy. Na ilustracji przedstawiono umiejscowienie i procedurę wymontowywania przycisku zasilania. 1. Wykręć śrubę (M1,6x2) mocującą wspornik przycisku zasilania do zestawu podparcia dłoni i klawiatury. 2. Wykręć śrubę (M1,6x2) mocującą płytę przycisku zasilania do zestawu podparcia dłoni i klawiatury, po czym zdejmij ją z tego zestawu.
1. Dopasuj otwór w płycie przycisku zasilania do otworu w zestawie podparcia dłoni i klawiatury. 2. Wkręć śrubę (M1,6x2) mocującą płytę przycisku zasilania do zestawu podparcia dłoni i klawiatury. 3. Dopasuj otwór we wsporniku przycisku zasilania do otworu w zestawie podparcia dłoni i klawiatury. 4. Wkręć śrubę (M1,6x2) mocującą wspornik przycisku zasilania do zestawu podparcia dłoni i klawiatury. 1. 2. 3. 4. 5. 6. Zainstaluj kartę I/O. Zainstaluj wentylator. Zainstaluj kartę sieci WLAN.
Wymontowywanie i instalowanie komponentów
1. Odklej taśmę mocującą płytę czytnika linii papilarnych do zestawu podparcia dłoni i klawiatury. 2. Otwórz zatrzask i odłącz kabel czytnika linii papilarnych od płyty czytnika linii papilarnych. 3. Otwórz zatrzask i odłącz kabel czytnika linii papilarnych od płyty systemowej. 4. Wyjmij przycisk zasilania z czytnikiem linii papilarnych razem z kablem przycisku zasilania z zestawu podparcia dłoni i klawiatury. 5. Odklej taśmę mocującą wspornik przycisku zasilania do zestawu podparcia dłoni i klawiatury. 6.
Wymontowywanie i instalowanie komponentów
1. Umieść przycisk zasilania z czytnikiem linii papilarnych w zestawie podparcia dłoni i klawiatury. 2. Wkręć śrubę (M1,6x2) mocującą przycisk zasilania z czytnikiem linii papilarnych do zestawu podparcia dłoni i klawiatury. 3. Dopasuj otwory na śruby we wsporniku przycisku zasilania do otworów w zestawie podparcia dłoni i klawiatury. 4. Wkręć trzy śruby mocujące wspornik przycisku zasilania do zestawu podparcia dłoni i klawiatury. 5.
Płyta systemowa Wymontowywanie płyty systemowej 1. 2. 3. 4. 5. 6. 7. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wymontuj pokrywę dolną. Wymontuj akumulator. Wyjmij zainstalowaną kartę SSD (SSD M.2 2280 lub SSD M.2 2230) Wymontuj kartę sieci WLAN. Wymontuj wentylator. Wymontuj radiator. Na ilustracji przedstawiono umiejscowienie i procedurę wymontowywania płyty systemowej. 1. Odklej taśmę mocującą kabel płyty we/wy do płyty systemowej. 2.
7. Otwórz zatrzask i odłącz kabel podświetlenia klawiatury od płyty systemowej. 8. Odłącz kabel baterii pastylkowej od płyty systemowej. 9. Odłącz kabel gniazda zasilacza od płyty systemowej. 10. Pociągając za uchwyt, odłącz kabel wyświetlacza od płyty systemowej. 11. Wykręć śrubę (M2x4) mocującą płytę systemową do zestawu podparcia dłoni i klawiatury. 12.
7. Podłącz kabel klawiatury do płyty systemowej i zamknij zatrzask, aby zamocować kabel. 8. Podłącz kabel tabliczki dotykowej do płyty systemowej i zamknij zatrzask, aby zamocować kabel. 9. Podłącz kabel czytnika linii papilarnych do płyty systemowej i zamknij zatrzask, aby zamocować kabel. 10. Podłącz kabel głośników do płyty systemowej. 11. Podłącz kabel karty I/O do płyty systemowej i zamknij zatrzask, aby zamocować kabel. 12. Przyklej taśmę mocującą kabel płyty we/wy do płyty systemowej. 1. 2. 3. 4. 5.
Instalowanie osłony wyświetlacza W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Na ilustracji przedstawiono umiejscowienie i procedurę instalacji osłony wyświetlacza. Dopasuj osłonę wyświetlacza do pokrywy wyświetlacza i delikatnie wciśnij osłonę na miejsce. 1. 2. 3. 4. 5. Zainstaluj zestaw wyświetlacza. Zainstaluj kartę sieci WLAN. Zainstaluj akumulator. Zainstaluj pokrywę dolną.
Wymontowywanie i instalowanie komponentów
1. Rysikiem z tworzywa sztucznego wysuń uchwyt taśmy SR po obu stronach panelu wyświetlacza. 2. Wyciągnij małą część taśmy SR. 3. Obróć taśmę SR wokół rysika z tworzywa sztucznego. UWAGA Aby uniknąć przerwania/złamania taśmy SR, wyciągnij tylko jej niewielką część, a następnie nawijaj taśmę SR na rysik. 4. Unieś panel wyświetlacza i wyjmij go z pokrywy. 5. Odklej taśmę mocującą kabel wyświetlacza do pokrywy wyświetlacza. 6. Podnieś zatrzask złącza i odłącz kabel wyświetlacza od pokrywy wyświetlacza.
Wymontowywanie i instalowanie komponentów
1. Zdejmij przezroczyste folie ochronne z taśm SR. 2. Wyrównaj i przyklej obie taśmy SR do plastikowej krawędzi tylnej pokrywy wyświetlacza. 3. Zdejmij niebieskie folie ochronne z taśm SR. 4. Zaczynając od góry, wyrównaj i umieść panel wyświetlacza na tylnej pokrywie wyświetlacza. 5. Zdejmij papier zwalniający z folii dociskowej. 6. Przyklej folię dociskową do panelu wyświetlacza. 7.
6. Wymontuj osłonę wyświetlacza. Na ilustracji przedstawiono umiejscowienie i procedurę wymontowywania zawiasów wyświetlacza. 1. Wykręć cztery śruby (M2,5x2,5) mocujące zawiasy wyświetlacza do tylnej pokrywy wyświetlacza. 2. Wykręć dwie śruby (M2x2) mocujące zawiasy wyświetlacza do tylnej pokrywy wyświetlacza. 3. Przesuń i zdejmij zawiasy wyświetlacza z pokrywy wyświetlacza.
1. Dopasuj otwory na śruby w zawiasach do otworów w tylnej pokrywie wyświetlacza. 2. Wkręć dwie śruby (M2x2) mocujące zawiasy wyświetlacza do tylnej pokrywy wyświetlacza. 3. Wkręć cztery śruby (M2,5x2,5) mocujące zawiasy wyświetlacza do tylnej pokrywy wyświetlacza. 1. 2. 3. 4. 5. 6. Zainstaluj oprawę wyświetlacza. Zainstaluj zestaw wyświetlacza. Zainstaluj kartę sieci WLAN. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera.
1. Przyklej kamerę do kabla wyświetlacza (taśma), a następne podłącz kabel kamery do kamery i odwróć ją. 2. Za pomocą wypustki prowadzącej odwróć kamerę i przyklej ją do tylnej pokrywy wyświetlacza. 1. 2. 3. 4. 5. 6. 7. Zainstaluj panel wyświetlacza. Zainstaluj oprawę wyświetlacza. Zainstaluj zestaw wyświetlacza. Zainstaluj kartę sieci WLAN. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera.
1. Odklej taśmę mocującą kabel wyświetlacza do tylnej pokrywy wyświetlacza. 2. Zdejmij kabel wyświetlacza z tylnej pokrywy wyświetlacza. Instalowanie kabla wyświetlacza W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Na ilustracji przedstawiono umiejscowienie i procedurę instalacji kabla wyświetlacza. 1. Przyklej taśmę mocującą kabel wyświetlacza do tylnej pokrywy wyświetlacza. 2. Przymocuj kabel wyświetlacza do tylnej pokrywy wyświetlacza. 1.
5. Zainstaluj pokrywę dolną. 6. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Pokrywa wyświetlacza Wymontowywanie pokrywy tylnej wyświetlacza 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wymontuj pokrywę dolną. Wymontuj akumulator. Wymontuj kartę sieci WLAN. Wymontuj zestaw wyświetlacza. Wymontuj osłonę wyświetlacza. Wymontuj zawiasy wyświetlacza. Wymontuj panel wyświetlacza.
Połóż pokrywę wyświetlacza na płaskiej powierzchni. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Zainstaluj kamerę Zainstaluj kabel wyświetlacza Zainstaluj panel wyświetlacza. Zainstaluj zawiasy wyświetlacza. Zainstaluj oprawę wyświetlacza. Zainstaluj zestaw wyświetlacza. Zainstaluj kartę sieci WLAN. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Zestaw podparcia dłoni i klawiatury Wymontowywanie zestawu podparcia dłoni i klawiatury 1. 2.
Po wykonaniu czynności wstępnych pozostanie zestaw podparcia dłoni i klawiatury. UWAGA Płytę systemową można wyjąć bez demontowania radiatora. Instalowanie zestawu podparcia dłoni i klawiatury W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Na ilustracji przedstawiono umiejscowienie i procedurę instalacji zestawu podparcia dłoni i klawiatury. Połóż zestaw podparcia dłoni i klawiatury na płaskiej powierzchni. 1. 2. 3. 4. 5. 6. 7.
8. Zainstaluj akumulator. 9. Zainstaluj pokrywę dolną. 10. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera.
3 Program konfiguracji systemu Program konfiguracji systemu umożliwia zarządzanie komponentami tabletukomputeranotebooka i konfigurowanie opcji systemu BIOS.
Klawisze Nawigacja Esc Powrót do poprzedniej strony do momentu wyświetlenia ekranu głównego. Naciśnięcie klawisza Esc na ekranie głównym powoduje wyświetlenie komunikatu z monitem o zapisanie zmian i ponowne uruchomienie systemu. Opcje konfiguracji systemu UWAGA W zależności od tabletukomputeranotebooka oraz zainstalowanych urządzeń wymienione w tej sekcji pozycje mogą, ale nie muszą, pojawiać się na ekranie. Opcje ogólne Tabela 2.
Informacje o systemie Tabela 3. System Configuration (Konfiguracja systemu) Opcja Opis Integrated NIC Umożliwia skonfigurowanie zintegrowanego kontrolera sieci LAN. • • • SATA Operation Disabled (Wyłączone) — wbudowany kontroler sieci LAN jest wyłączony i niewidoczny w systemie operacyjnym. Enabled (Włączone) — wbudowany kontroler sieci LAN jest włączony.
Security (Zabezpieczenia) Tabela 4. Security (Zabezpieczenia) Opcja Opis Admin Password Umożliwia ustawianie, zmienianie i usuwanie hasła administratora. System Password Umożliwia ustawianie, zmienianie i usuwanie hasła systemowego. Strong Password Ta opcja umożliwia włączanie i wyłączanie wymuszania silnych haseł w systemie. Password Configuration Umożliwia określenie minimalnej i maksymalnej dozwolonej długości hasła administratora i hasła systemowego. Można ustawić od 4 do 32 znaków.
Opcja Opis OROM Keyboard Access Ta opcja określa, czy użytkownicy mogą otwierać ekran konfiguracji pamięci Option ROM za pomocą skrótów klawiaturowych podczas uruchamiania komputera. • • • Enabled (Włączone; ustawienie domyślne) Wyłączone One Time Enable (Włącz na jeden raz) Admin Setup Lockout Uniemożliwia użytkownikom otwieranie programu konfiguracji systemu, kiedy jest ustawione hasło administratora. Domyślnie ta opcja jest nieustawiona.
Intel Software Guard Extensions (Rozszerzenia Intel Software Guard) Tabela 6. Intel Software Guard Extensions (Rozszerzenia Intel Software Guard) Opcja Opis Intel SGX Enable To pole pozwala włączyć funkcję bezpiecznego środowiska do uruchamiania poufnego kodu/przechowywania poufnych informacji w kontekście głównego systemu operacyjnego.
Zarządzanie energią Opcja Opis AC Behavior Umożliwia włączanie i wyłączanie funkcji automatycznego uruchamiania komputera po podłączeniu zasilacza sieciowego. Ustawienie domyślne: opcja Wake on AC nie jest zaznaczona.
POST Behavior (Zachowanie podczas testu POST) Opcja Opis Adapter Warnings Umożliwia włączanie i wyłączanie komunikatów ostrzegawczych systemu BIOS, emitowanych w przypadku korzystania z niektórych zasilaczy. Ustawienie domyślne: Enable Adapter Warnings Numlock Enable Umożliwia włączanie i wyłączanie klawisza Num Lock przy uruchamianiu komputera. Enable Network (Włącz sieć). Ta opcja jest domyślnie włączona.
Wireless (Komunikacja bezprzewodowa) Opis opcji Wireless Switch Umożliwia wybieranie urządzeń, których działaniem ma sterować przełącznik urządzeń bezprzewodowych. Dostępne opcje: • • WLAN Bluetooth Wszystkie opcje są domyślnie włączone. UWAGA Opcje włączania i wyłączania funkcji WLAN są połączone i nie można ich włączać lub wyłączać niezależnie od siebie. Wireless Device Enable Umożliwia włączanie i wyłączanie wewnętrznych urządzeń bezprzewodowych.
SupportAssist System Resolution (Konsola SupportAssist System Resolution) Opcja Opis Auto OS Recovery Umożliwia sterowaniem automatycznym rozruchem systemu na potrzeby funkcji SupportAssist. Dostępne opcje: Threshold • Nie świeci • 1 • 2 (opcja domyślnie włączona) • 3 SupportAssist OS Recovery Umożliwia odzyskanie systemu SupportAssist (opcja domyślnie wyłączonawłączona) Hasło systemowe i hasło konfiguracji systemu Tabela 8.
Usuwanie lub zmienianie hasła systemowego i hasła dostępu do ustawień systemu Przed usunięciem lub zmianą istniejącego hasła systemowego lub hasła konfiguracji systemu należy się upewnić, że dla opcji Password Status (Stan hasła) jest wybrane ustawienie Unlocked (Odblokowane) w programie konfiguracji systemu. Jeśli dla opcji Password Status (Stan hasła) jest wybrane ustawienie Locked (Zablokowane), nie można zmienić ani usunąć tych haseł.
4 Rozwiązywanie problemów Program diagnostyczny ePSA (Enhanced Pre-Boot System Assessment) Test diagnostyczny ePSA obejmuje pełną kontrolę elementów sprzętowych. Test ePSA jest wbudowany w systemie BIOS i uruchamiany wewnętrznie przez system BIOS.
Na przykład kontrolka stanu zasilania i stanu akumulatora miga dwa razy światłem bursztynowym, a potem następuje pauza, a następnie światłem białym trzy razy, a potem następuje pauza. Sekwencja 2,3 jest wykonywana do chwili wyłączenia komputera. Oznacza ona brak pamięci lub pamięci RAM. Poniższa tabela przedstawia różne sekwencje lampek stanu zasilania i akumulatora oraz powiązane problemy. Tabela 9.
2. Przejdź do strony internetowej www.dell.com/support. 3. Kliknij pozycję Product Support (Wsparcie dla produktu), wprowadź znacznik serwisowy komputera, a następnie kliknij przycisk Submit (Prześlij). UWAGA Jeśli nie masz znacznika serwisowego, skorzystaj z funkcji automatycznego wykrywania znacznika albo ręcznie wyszukaj model swojego komputera. 4. Kliknij pozycję Drivers & downloads (Sterowniki i pliki do pobrania) > Find it myself (Znajdę samodzielnie). 5.
5 Uzyskiwanie pomocy Tematy: • Kontakt z firmą Dell Kontakt z firmą Dell UWAGA W przypadku braku aktywnego połączenia z Internetem informacje kontaktowe można znaleźć na fakturze, w dokumencie dostawy, na rachunku lub w katalogu produktów firmy Dell. Firma Dell oferuje kilka różnych form obsługi technicznej i serwisu, online oraz telefonicznych. Ich dostępność różni się w zależności od produktu i kraju, a niektóre z nich mogą być niedostępne w regionie użytkownika.