Vostro 15 5515 Servicehandbok Regleringsmodell: P106F Regleringstyp: P106F003 April 2021 Rev.
Anmärkningar, försiktighetsbeaktanden och varningar OBS: OBS innehåller viktig information som hjälper dig att få ut det mesta av produkten. CAUTION: VIKTIGT anger antingen risk för skada på maskinvara eller förlust av data och förklarar hur du kan undvika problemet. VARNING: En VARNING visar på en potentiell risk för egendoms-, personskador eller dödsfall. © 2021 Dell Inc. eller dess dotterbolag. Med ensamrätt. Dell, EMC och andra varumärken är varumärken som tillhör Dell Inc. eller dess dotterbolag.
Innehåll Kapitel 1: Arbeta inuti datorn............................................................................................................6 Innan du arbetar inuti datorn................................................................................................................................................6 Säkerhetsanvisningar............................................................................................................................................................
Installera knappcellsbatteriet........................................................................................................................................34 Kylfläns..................................................................................................................................................................................35 Ta bort kylflänsen........................................................................................................................................
Återställ operativsystemet..................................................................................................................................................72 Flash-uppdatera BIOS (USB-minne).................................................................................................................................72 Flash-uppdatera BIOS.........................................................................................................................................................
1 Arbeta inuti datorn Ämnen: • • • • • Innan du arbetar inuti datorn Säkerhetsanvisningar Skydd mot elektrostatisk urladdning (ESD) Fältservicekit för ESD När du har arbetat inuti datorn Innan du arbetar inuti datorn OBS: Bilderna i det här dokumentet kan skilja från din dator beroende på konfigurationen du beställde. 1. Spara och stäng alla öppna filer samt avsluta alla öppna program. 2. Stäng av datorn. Klicka på Start > Stänga > av strömmen.
du rikta in dem rakt för att undvika att kontaktstiften böjs. När du ansluter kablar ska du se till att portar och kontakter är korrekt vända och inriktade. CAUTION: Tryck in och mata ut eventuella kort från mediekortläsaren. OBS: Färgen på datorn och vissa komponenter kan skilja sig från de som visas i det här dokumentet. Meddelande om strålningsexponering Den här enheten uppfyller myndighetskraven för exponering för radiovågor.
Komponenterna i ett fältservicekit för ESD Komponenterna i ett fältservicekit för ESD är: ● Antistatisk matta - Den antistatiska mattan är dissipativ och delar kan placeras på den under serviceförfaranden. När du använder en antistatisk matta din handledsrem ska sitta åt och jordningstråden ska kopplas till mattan och till någon omålad metall på systemet som du arbetar på. När den har anslutits ordentligt kan reservdelar tas ut från ESD-påsen och placeras direkt på mattan.
2 Ta bort och installera komponenter OBS: Bilderna i det här dokumentet kan skilja från din dator beroende på konfigurationen du beställde. Ämnen: • • • • • • • • • • • • • • • • • • • • • • Rekommenderade verktyg Skruvlista Huvudkomponenter i Vostro 15 5515 Kåpan Batteriet Batterikabel Minne SSD-disk – M.2-kortplats nr ett SSD-disk – M.
Tabell 1. Skruvlista Komponent Skruvtyp Kvantitet Baskåpa ● Fästskruvar – M2x7,5 ● M2x4 ● 2 ● 7 Skruvbild ● ● 3-cellsbatteri M2x3 3 4-cellsbatteri M2x3 4 Trådlöst kort M2x3 1 SSD-disk - plats 1 M2x3 1 SSD-disk - plats 2 M2x3 1 Fläkt M2x3 2 Kylfläns Fästskruvar 4 Moderkort M2x2 3 Fäste för USB Typ C M2x4 2 Strömbrytare med fingeravtrycksläsare M2x3 1 Nätverksportens fäste M2x5 2 I/O-kort M2x2 1 Styrplatta M1,6x2 3 M2x1.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Baskåpa Kylfläns Moderkort Minne Batteri Höger högtalare Handledsstöds- och tangentbordsmontering Styrplatta Bildskärmsmontering Knappcellsbatteri I/O-kort M.2 2280 SSD-disk, om installerad Trådlöst kort M.
16. Fläkt 17. Nätaggregatsport OBS: Dell innehåller en lista över komponenter och tillhörande artikelnummer för den ursprungliga systemkonfigurationen som köpts. Dessa delar är tillgängliga enligt garantitäckningar som kunden har köpt. Kontakta din Dell-säljare för köpalternativ. Kåpan Ta bort baskåpan 1. Följ anvisningarna i Innan du arbetar inuti datorn. Följande bilder anger placeringen av baslocket och ger en visuell representation av borttagningsförfarandet.
1. Lossa de två (M2x7,5) fästskruvarna som håller fast baskåpan i handledsstöds- och tangentbordsenheten. 2. Ta bort de sju (M2x4) skruvarna som håller fast kåpan i handledsstöds- och tangentbordsmonteringen. 3. Använd en plastrits för att bända upp baskåpan från de U-formade jacken vid den övre kanten på baskåpan och fortsätt att lossa baskåpan från handledsstöds- och tangentbordsmonteringen från sidorna. 4. Lyft av baskåpan från handledsstöds- och tangentbordsmonteringen. 5.
7. Tryck och håll strömbrytaren intryckt i 20 sekunder för att jorda datorn och tömma den kvarvarande strömmen. Installera baskåpan Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. Följande bild anger placeringen av baslocket och ger en visuell representation av intstallationsförfarandet.
1. Anslut batterikabeln till moderkortet. 2. Fäst tejpen för fästa batterikabeln. 3. Placera baskåpan på handledstöds- och tangentbordsmonteringen. 4. Rikta in skruvhålen på kåpan med skruvhålen i handledsstöds- och tangentbordsmonteringen och fäst sedan fast baskåpan på plats. 5. Dra åt de två (M2x7,5) fästskruvarna som håller fast baskåpan i handledsstöds- och tangentbordsenheten. 6. Sätt tillbaka de sju (M2x4) skruvarna som håller fast kåpan i handledsstöds- och tangentbordsmonteringen. 1.
Ta bort 3-cellsbatteriet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan. Följande bild visar platsen för 3-cellsbatteriet (41 Wh) och ger en visuell representation av borttagningsproceduren. 1. Dra bort bandet som håller fast batterikabeln på moderkortet. 2. Koppla bort batterikabeln från moderkortet. 3. Ta bort de tre (M2x3) skruvarna som fäster 3-cellsbatteriet på handledsstöds- och tangentbordsenheten. 4.
1. Med hjälp av justeringsstolparna placerar du 3-cellsbatteriet på handledsstöds- och tangentbordsenheten. 2. Rikta in skruvhålen på 3-cellsbatteriet mot skruvhålen på handledsstöds- och tangentbordsenheten. 3. Sätt tillbaka de tre (M2x3) skruvarna som fäster 3-cellsbatteriet på handledsstöds- och tangentbordsenheten. 4. Anslut batterikabeln till moderkortet. 5. Sätt fast tejpen som håller fast batterikabeln på moderkortet. 1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat på datorn.
1. Dra bort bandet som håller fast batterikabeln på moderkortet. 2. Koppla bort batterikabeln från moderkortet. 3. Ta bort de fyra (M2x3) skruvarna som fäster 4-cellsbatteriet på handledsstöds- och tangentbordsenheten. 4. Lyft upp 4-cellsbatteriet och dess kabel , från handledsstöds- och tangentbordsenheten. Installera 4-cellsbatteriet Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren.
2. Rikta in skruvhålen på 4-cellsbatteriet mot skruvhålen på handledsstöds- och tangentbordsenheten. 3. Sätt tillbaka de fyra (M2x3) skruvarna som fäster 4-cellsbatteriet på handledsstöds- och tangentbordsenheten. 4. Anslut batterikabeln till moderkortet. 5. Sätt fast tejpen som håller fast batterikabeln på moderkortet. 1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat på datorn. Batterikabel Ta bort batterikabeln 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan.
1. Justera och placera batterikabeln på batteriet. 2. Dra kabeln för batteriet genom kabelhållarna på batteriet. 3. Anslut batterikabeln till kontakten på batteriet. 1. Installera 3-cellsbatteriet eller 4-cellsbatteriet, beroende på vilket som gäller. 2. Installera baskåpan. 3. Följ anvisningarna i När du har arbetat på datorn. Minne Ta bort minnesmodulen 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan.
1. Lyft bort mylartejpen för att komma åt minnesmodulen. 2. Använd fingertopparna för att dra bort låsklämmorna från båda sidor av minnesmodulen tills minnesmodulen hoppar upp. 3. Ta bort minnesmodulen från minnesmodulkortplatsen. OBS: Upprepa steg 1 till 3 för att ta bort andra minnesmoduler installerade i datorn. Installera minnesmodulen Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren.
1. Lyft bort mylartejpen för att komma åt minnesmodulkortplatsen. 2. Rikta in spåret på minnesmodulen med fliken på minnesmodulplatsen. 3. Skjut minnesmodulen ordentligt i en vinkel in i minnesmodulplatsen. 4. Tryck minnesmodulen nedåt tills den klickar på plats. OBS: Om du inte hör något klick tar du bort minnesmodulen och försöker igen. OBS: Upprepa steg 1 till 4 för att installera andra minnesmoduler i datorn. 1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat inuti datorn. SSD-disk – M.
OBS: Undvik dataförlust genom att inte ta bort SSD-disken medan datorn är i strömsparläge eller är påslagen. 2. Ta bort baskåpan. OBS: Beroende på vilken konfiguration som beställts kan datorn ha stöd för en 2230-SSD-disk eller en 2280-SSD-disk på M.2kortplats nr ett. OBS: Den här proceduren gäller bara för datorer som levereras med en 2230 SSD-disk installerad på M.2-kortplats nr ett. Den följande bilden visar placeringen av 2230-SSD-disken som installerats på M.
1. Rikta in spåret på 2230 SSD-disken med fliken på kortplatsen för SSD-disken. 2. För in 2230 SSD-disken ordentligt i kortplatsen för SSD-disken vid en vinkel. 3. Rikta in skruvhålet på SSD-disken med skruvhålet på handledsstöds- och tangentbordsenheten. 4. Sätt tillbaka skruven (M2x3) som fäster 2230-SSD-disken vid handledsstöds- och tangentbordsenheten. 1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat inuti datorn. Ta bort 2280-SSD-disken från M.2-kortplats nr ett 1.
1. Ta bort skruven (M2x3) som fäster SSD-disken på handledsstöds- och tangentbordsmonteringen. 2. Skjut ut och lossa 2280 SSD-disken från M.2 SSD-kortplats ett på moderkortet. Installera 2280 SSD-disken på M.2-kortplats nr ett Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. OBS: SSD-diskar är ömtåliga. Var försiktig när du hanterar SSD-disken.
1. Rikta in spåret på 2280 SSD-disken med fliken på kortplatsen för SSD-disken. 2. För in 2280 SSD-disken ordentligt i kortplatsen för SSD-disken vid en vinkel. 3. Rikta in skruvhålet på SSD-disken med skruvhålet på handledsstöds- och tangentbordsenheten. 4. Sätt tillbaka skruven (M2x3) som fäster 2280-SSD-disken vid handledsstöds- och tangentbordsenheten. 1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat inuti datorn. Installera SSD-diskens monteringsfäste på M.
1. Skjut och ta bort SSD-diskens monteringsfäste från monteringsfästets plats på handledsstöds- och tangentbordsmonteringen. 2. Vrid på SSD-diskens monteringsfäste 180 grader. 3. Skjut in SSD-diskens monteringsfäste i monteringsplatsen på handledsstöds- och tangentbordsmonteringen. 4. Installera 2230-SSD-disken eller 2280-SSD-disken, beroende på vilket som gäller. SSD-disk – M.2-kortplats nr två Ta bort 2230-SSD-disken från M.2-kortplats nr två OBS: M.2-plats två stöder endast 2230 SSD-disk.
1. Ta bort skruven (M2x3) som håller fast det termiska skyddet för SSD-disken och SSD-disken i handledsstöds- och tangentbordsmonteringen. 2. Skjut ut och lyft bort SSD-diskens värmeskydd från SSD-disken. 3. Skjut och ta bort SSD-disken från M.2-kortplats två. Installera 2230-SSD-disken i M.2-kortplats nr två Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. OBS: SSD-diskar är ömtåliga. Var försiktig när du hanterar SSD-disken. OBS: M.
Den följande bilden visar placeringen av 2230-SSD-disken som installerats på M.2-kortplats nr två, och ger en visuell representation av installationsproceduren. 1. Rikta in spåret på 2230-SSD-disken med fliken på M.2-kortplats nr två på moderkortet. 2. Skjut in 2230-SSD-disken i M.2-kortplats nr två på moderkortet. 3. Placera SSD-diskens värmeskydd på SSD-disken. 4. Rikta in skruvhålet på SSD-diskens värmeskydd med skruvhålet på handledsstöds- och tangentbordsenheten. 5.
Trådlöst kort Ta bort det trådlösa kortet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan. Följande bilder visar platsen för det trådlösa kortet och ger en visuell representation av borttagningsproceduren. 1. Ta bort skruven (M2x3) som håller fast fästet för det trådlösa kortet på det trådlösa kortet och moderkortet. 2. Ta bort fästet för det trådlösa kortet från det trådlösa kortet. 3. Koppla bort antennkablarna från det trådlösa kortet. 4.
1. Anslut antennkablarna till det trådlösa kortet. Följande tabell visar färgschemat för antennkablarna för de kort för trådlös teknik som stöds av datorn. Tabell 2. Färgschema för antennkablar Kontakter på det trådlösa kortet Färg på antennkabel Silkscreen-märkning Main (huvudmeny) Vit MAIN (huvudmeny) △ (vit triangel) Sekundär Svart AUX ▲ (svart triangel) 2. Rikta in spåret på det trådlösa kortet med fliken på kortplatsen för det trådlösa kortet på moderkortet. 3.
Fläkt Ta bort fläkten 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan. Följande bild visar fläktens placering och ger en visuell representation av borttagningsproceduren. 1. Koppla bort fläktkabeln från moderkortet. 2. Ta bort de två skruvarna (M2x3) som fäster fläkten i handledsstöds- och tangentbordsenheten. 3. Lyft av fläkten från handledsstöds- och tangentbordsmonteringen.
1. Med hjälp av justeringsstolparna placerar du fläkten på handledsstöds- och tangentbordsenheten. 2. Sätt tillbaka de två (M2x3) skruvarna för att fästa fläkten på handledsstöds- och tangentbordsenheten. 3. Anslut fläktkabeln till moderkortet. 1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat inuti datorn. Knappcellsbatteri Ta bort knappcellsbatteriet 1. Följ anvisningarna i Innan du arbetar inuti datorn.
1. Koppla bort kabeln för knappcellsbatteriet från I/O-kortet. 2. Använd en plastrits för att dra bort knappcellsbatteriet från handledsstöds- och tangentbordsmonteringen. Installera knappcellsbatteriet Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. Följande bild visar platsen för knappcellsbatteriet och ger en visuell representation av installationsproceduren.
1. Fäst knappcellsbatteriet till kortplatsen på handledsstöds- och tangentbordsmonteringen. 2. Anslut knappcellsbatterikabeln till I/O-kortet. 1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat inuti datorn. Kylfläns Ta bort kylflänsen 1. Följ anvisningarna i Innan du arbetar inuti datorn. CAUTION: För att processorn ska kylas maximalt bör du inte röra vid kylflänsens värmeöverföringsytor. Fett och oljor från din hud kan reducera värmeöverföringskapaciteten i det termiska fettet.
1. Lossa de fyra fästskruvarna som fäster kylflänsen vid moderkortet i rätt ordning (anges på kylflänsen). 2. Lyft bort kylflänsen från moderkortet. Installera kylflänsen Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. CAUTION: Felaktig inriktning av kylflänsen kan orsaka skada på moderkortet och processorn. OBS: Om moderkortet eller kylflänsen byts ut ska du använda det termiska skyddet/krämen som medföljer i satsen för att säkerställa kylning.
1. Rikta in skruvhålen på kylflänsen mot skruvhålen på moderkortet. 2. Dra åt i rätt ordning (anges på kylflänsen) fyra fästskruvarna som håller fast kylflänsen i moderkortet. 1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat inuti datorn. Nätverksportens fäste Ta bort fästet för nätverksporten 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan. Följande bild(er) visar platsen för nätverksportens fäste och ger en visuell representation av borttagningsproceduren.
1. Ta bort de två (M2x5) skruvarna som håller fast nätverksportens fäste på I/O-kortet. 2. Lyft bort fästet för nätverksporten från I/O-kortet. Installera fästet för nätverksporten Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. Följande bild(er) visar platsen för nätverksportens fäste och ger en visuell representation av installationsproceduren. 1. Placera fästet för nätverksporten på I/O-kortet. 2.
1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat inuti datorn. I/O-kort Ta bort I/O-kortet 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan. 3. Ta bort fästet för nätverksporten. Följande bilder visar moderkortets placering på I/O-kortet och ger en visuell återgivning av borttagningsproceduren. 1. Ta bort de tre (M2,5x4,5) skruvarna som fäster det vänstra bildskärmsgångjärnet vid handledsstöds- och tangentbordsmonteringen. 2.
1. Skjut I/O-kortet i facken på handledsstöds- och tangentbordsenheten. 2. Rikta in skruvhålet på I/O-kortet med skruvhålet på handledsstöds- och tangentbordsmonteringen. 3. Sätt tillbaka skruven (M2x2) som håller fast I/O-kortet i handledsstöds- och tangentbordsmonteringen. 4. Anslut strömbrytaren med den valfria fingeravtrycksläsarens kabel till kontakten på I/O-kortet och stäng spärren för att fästa kabeln. 5. Anslut knappcellsbatterikabeln till I/O-kortet. 6.
1. Öppna spärren och koppla bort kabeln till det bakgrundsbelysta tangentbordet, tangentbordskabeln och styrplattans kabel från moderkortet. 2. Observera hur högtalarkabeln är dragen och ta bort högtalarkabeln från kabelhållarna på handledsstöds- och tangentbordsmonteringen. 3. Dra av tejpen som håller fast högtalarkabeln i handledsstöds- och tangentbordsenheten. 4. Koppla bort högtalarkabeln från moderkortet. 5. Lyft ut högtalarna, tillsammans med kabeln, från handledsstöds- och tangentbordsmonteringen.
1. Använd justeringstapparna och gummitågringarna för att placera högtalarna i facken på handledsstöds- och tangentbordsmonteringen. 2. Anslut högtalarkabeln till moderkortet. 3. Dra högtalarkabeln genom kabelhållarna på handledsstöds- och tangentbordsmonteringen. 4. Anslut kabeln för tangentbordets bakgrundsbelysning, tangentbordskabeln och styrplattans kabel till kontakterna på moderkortet och stäng spärren så att kabeln sitter fast. 1. Installera baskåpan. 2.
Följande bilder visar styrplattans placering och ger en visuell representation av borttagningsproceduren. 1. Öppna spärren och koppla ur styrplattans kabel från moderkortet. 2. Ta bort de tre skruvarna (M1.6x2) som håller fast styrplattans fäste i handledsstöds- och tangentbordsmonteringen. 3. Ta bort tejpen som fäster styrplattans fäste vid handledsstöds- och tangentbordsmonteringen. 4. Lyft bort styrplattans fäste från handledsstöds- och tangentbordsmonteringen. 5.
1. Skjut styrplattan in i luckan på handledsstöds- och tangentbordsenheten. OBS: Vänd på datorn och öppna skärmen. Kontrollera att styrplattan är lika justerad längs alla fyra sidor. 2. Sätt tillbaka de två skruvarna (M2x1,8) som håller fast styrplattan i handledsstöds- och tangentbordsmonteringen. 3. Fäst tejpen som håller fast styrplattan vid handledsstöds- och tangentbordsmonteringen. 4. Rikta in skruvhålen på styrplattan mot skruvhålen på handledsstöds- och tangentbordsmonteringen. 5.
Ta bort och installera komponenter 45
1. Dra bort tejpen som håller fast bildskärmskabeln på moderkortet. 2. Öppna kontaktspärren och koppla ur bildskärmskabeln från moderkortet. 3. Ta bort de tre (M2,5x4,5) skruvarna som håller fast det vänstra displaygångjärnet på moderkortet. 4. Ta bort de tre (M2,5x4,5) skruvarna som håller fast det högra displaygångjärnet på moderkortet. 5. Öppna bildskärmsgångjärnen i en vinkel på 90 grader. 6. Skjut bort handledsstöds- och tangentbordsmonteringen från bildskärmsmonteringen.
1. Skjut in bildskärmsenheten i en vinkel och placera bildskärmsenheten på handledsstöds- och tangentbordsenheten. 2. Med hjälp av justeringsposter, stäng bildskärms-gångjärnen. 3. Sätt tillbaka de tre (M2,5x4,5) skruvarna som håller fast det högra displaygångjärnet på moderkortet. 4. Sätt tillbaka de tre (M2,5x4,5) skruvarna som håller fast det vänstra displaygångjärnet på moderkortet. 5. Skjut in bildskärmskabeln i kontakten på moderkortet och stäng spärren så att kabeln sitter fast. 6.
Strömbrytare med fingeravtrycksläsare som tillval Ta bort strömbrytaren med valfri fingeravtrycksläsare 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan. 3. Ta bort I/O-kortet. Följande bild visar platsen för strömbrytaren med fingeravtrycksläsare som tillval och ger en visuell representation av borttagningsproceduren. 1. Ta bort skruven (M2x3) som håller fast strömbrytaren med valfri fingeravtrycksläsare i handledsstöds- och tangentbordsenheten. 2.
1. Justera och placera strömbrytaren med den valfria fingeravtrycksläsaren på handledsstöds- och tangentbordsenheten, 2. Sätt tillbaka skruven (M2x3) som håller fast strömbrytaren med valfri fingeravtrycksläsare i handledsstöds- och tangentbordsenheten. 1. Installera I/O-kortet. 2. Installera baskåpan. 3. Följ anvisningarna i När du har arbetat inuti datorn. Nätadapterport Ta bort nätaggregatporten 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan.
1. Ta bort de tre (M2,5x4,5) skruvarna som håller fast det högra displaygångjärnet på moderkortet. 2. Öppna bildskärmsgångjärnet i en vinkel på 90 grader. 3. Koppla bort kabeln för nätaggregatporten från moderkortet. 4. Dra bort tejpen som håller fast kabeln till nätaggregatsporten på moderkortet. 5. Ta bort kabeln för nätaggregatsporten från kabelhållarna på handledsstöds- och tangentbordsenheten. 6. Lyft av nätadapterporten tillsammans med kabeln från handledsstöds- och tangentbordsmonteringen.
1. Placera strömadapterporten, tillsammans med dess kabel, i spåret på handledsstöds- och tangentbordsenheten. 2. Dra kabeln för nätaggregatsporten genom kabelhållarna på handledsstöds- och tangentbordsenheten. 3. Fäst tejpen som håller fast kabeln till nätaggregatporten på moderkortet. 4. Anslut kabeln för nätaggregatporten till moderkortet. 5. Stäng höger bildskärmsgångjärn och rikta in skruvhålen på höger bildskärmsgångjärn med skruvhålen på moderkortet och handledsstöds- och tangentbordsmonteringen. 6.
OBS: Moderkortet kan tas bort och installeras med kylflänsen monterad när du byter ut och sätter tillbaka andra delar för att förenkla proceduren och bevara den termiska förbindelsen mellan moderkortet och kylflänsen. Följande bild visar kontakterna på moderkortet. Figur 1. Kontakter på moderkortet 1. 2. 3. 4. 5. 6. 7. 8. 9.
Ta bort och installera komponenter 53
1. Ta bort de tre (M2,5x4,5) skruvarna som fäster det högra bildskärmsgångjärnet vid handledsstöds- och tangentbordsmonteringen. 2. Öppna det högra bildskärmsgångjärnet i en vinkel på 90 grader. 3. Dra bort tejpen som håller fast bildskärmskabeln på moderkortet. 4. Öppna kontaktspärren och koppla ur bildskärmskabeln från moderkortet. 5. Dra bort tejpen och koppla bort nätadapterportens kabel från moderkortet. 6. Ta bort de två (M2x4) skruvarna som fäster USB Type-C-fästet vid moderkortet. 7.
Figur 2. Kontakter på moderkortet 1. 2. 3. 4. 5. 6. 7. 8. 9. Kabelkontakt för bildskärm Nätadapterportens kabelkontakt Det bakgrundsbelysta tangentbordets kabelkontakt Tangentbordets kabelkontakt Styrplattans kabelkontakt Batterikabelns kontakt Fläktens kabelkontakt Kontakt för högtalarkabel kontakt för kabel till I/O-kort Följande bild visar var moderkortet är placerat och hur installationsproceduren går till.
Ta bort och installera komponenter
1. Justera och placera moderkortet på handledsstöds- och tangentbordsenheten. 2. Sätt tillbaka de tre skruvarna (M2x2) som fäster moderkortet i handledsstöds- och tangentbordsenheten. 3. Anslut bildskärmskabeln till moderkortet och stäng haken så att kabeln sitter fast ordentligt. 4. Sätt fast tejpen som håller fast bildskärmskabeln på moderkortet. 5. Anslut kabeln för nätaggregatporten till moderkortet. 6. Fäst tejpen som håller fast kabeln till nätaggregatporten på moderkortet. 7.
15. Stäng det högra bildskärmsgångjärnet. 16. Sätt tillbaka de tre (M2,5x4,5) skruvarna som fäster det högra - bildskärmsgångjärnet vid handledsstöds- och tangentbordsmonteringen. 1. 2. 3. 4. 5. 6. 7. 8. 9. Installera kylflänsen. Installera fläkten. Installera trådlösa kortet. Installera M.2 2280 SSD-disken eller M.2 2230 SSD-disken i M.2-kortplats ett, beroende på vilket som gäller. Installera M.2 2230 SSD-disken i M.2-kortplats två, om tillämpligt. Installera minnesmodulen.
Installera handledsstöds- och tangentbordsmonteringen Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. Placera handledsstöds- och tangentbordsmonteringen på en plan yta.
1. 2. 3. 4. 5. 6. Installera bildskärmsmonteringen. Installera styrplattan. Installera högtalarna. Installera nätaggregatsporten. Installera strömbrytaren med fingeravtrycksläsare som tillval. Installera moderkortet. OBS: Moderkortet kan installeras tillsammans med kylflänsen. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 60 Installera I/O-kortet. Installera fläkten. Installera knappcellsbatteriet. Installera trådlösa kortet. Installera M.2 2280 SSD-disken eller M.2 2230 SSD-disken i M.
3 Drivrutiner och hämtningsbara filer Vid felsökning, hämtning eller installation av drivrutiner rekommenderas läsning av Dells kunskapsartikel Vanliga frågor om drivrutiner och hämtningsbara filer SLN128938.
4 Systeminstallationsprogram CAUTION: Såvida du inte är en mycket kunnig datoranvändare bör du inte ändra inställningarna i BIOSinställningsprogrammet. Vissa ändringar kan medföra att datorn inte fungerar som den ska. OBS: Innan du ändrar BIOS-inställningsprogrammet rekommenderar vi att du antecknar informationen som visas på skärmen i BIOS-inställningsprogrammet och sparar den ifall du skulle behöva den senare.
Startsekvens Startsekvens ger dig möjlighet att kringgå den systeminställningsspecifika startenhetsordningen och starta direkt till en viss enhet (till exempel: optisk enhet eller hårddisk). Under självtest (POST), när Dell-logotypen visas kan du: ● Starta systemkonfiguration genom att trycka på tangenten F2 ● Öppna engångsstartmenyn genom att trycka på tangenten F12. Engångsstartmenyn visar de enheter som du kan starta från inklusive diagnostikalternativet.
Tabell 4. Systeminstallationsalternativ – menyn Avancerat (fortsättning) Avancerat Integrerad NIC Tillåter att nätverksfunktioner före OS-start och i början av OS-start använder aktiverade NIC:er. Alternativen är: ● Enabled (aktiverat) (standardinställning) ● Disabled (inaktiverat) USB Emulation Här kan du aktivera USB-emulering. Alternativen är: ● Enabled (aktiverat) (standardinställning) ● Disabled (inaktiverat) SATA Operation (SATA-drift) Här kan du välja datorns SATA-läge.
Tabell 4. Systeminstallationsalternativ – menyn Avancerat (fortsättning) Avancerat Alternativen är: ● Enabled (aktiverat) (standardinställning) ● Disabled (inaktiverat) Internal WLAN Här kan du slå på/stänga av det trådlösa kortet. Alternativen är: ● Enabled (aktiverat) (standardinställning) ● Disabled (inaktiverat) Mediakortläsare Gör det möjligt att aktivera/inaktivera mediakortläsaren.
Tabell 4. Systeminstallationsalternativ – menyn Avancerat Avancerat ● Enabled (aktiverat) SupportAssist-systemupplösning Omborddiagnostik Auto OS Recovery Threshold Utför SupportAssist OS Recovery efter det angivna värdet för misslyckade startförsök. Alternativen är: ● Off (av) ● 1 ● 2 (standard) ● 3 Support Assist OS Recovery Aktiverad Support Assist-operativsystemsåterställning vid misslyckade startförsök.
Tabell 5. Systemkonfigurationsalternativ – Säkerhetsmenyn Security (säkerhet) ● Disabled (inaktiverad) (standardinställning) ● Enabled (aktiverat) Attestation Enable (aktivera attestering) Ger användaren möjlighet att kontrollera om TPM-godkännandehierarki är tillgänglig för operativsystemet.
Tabell 7. Systeminstallationsalternativ—menyn Exit (avsluta) Exit (avsluta) Exit Savings Changes Avsluta systeminstallationsprogrammet och spara ändringarna som gjorts i installationsalternativen. Spara ändring utan att avsluta Spara ändringarna som har gjorts i systeminstallationsprogrammet och fortsätt med installationen. Avsluta och ignorera inställningar Avsluta systeminstallationsprogrammet utan att spara ändringarna som gjorts i installationsalternativen.
Radera eller ändra ett befintligt systeminstallationslösenord Kontrollera att lösenordsstatus är upplåst (i systeminstallation) innan du försöker ta bort eller ändra det befintliga system- och installationslösenordet. Du kan inte ta bort eller ändra ett befintligt system- eller installationslösenord om lösenordsstatus är låst. Starta systeminstallationsprogrammet genom att trycka på F2 omedelbart efter det att datorn startats eller startats om. 1.
5 Felsökning Ämnen: • • • • • • • • • Dell SupportAssist-diagnostik för kontroll av systemprestanda före start Systemets diagnosindikatorer Återställ operativsystemet Flash-uppdatera BIOS (USB-minne) Flash-uppdatera BIOS M-BIST LCD inbyggda självtestet (BIST) WiFi-cykel Ladda ur väntelägesström Dell SupportAssist-diagnostik för kontroll av systemprestanda före start SupportAssist-diagnostiken (även kallad systemdiagnostik) utför en fullständig kontroll av din maskinvara.
Indikerar status för ström och batteriladdning. Fast vitt sken — Nätaggregatet är anslutet och batteriet har mer än 5 procent laddning. Gult sken — Datorn drivs med batteriet och batteriet har mindre än 5 procent laddning. Off (av) – laddas ur eller andra strömlägen ● Nätaggregatet är anslutet och batteriet är fulladdat. ● Datorn drivs med batteriet och batteriet har mer än 5 procent laddning. ● Datorn är i strömsparläge, viloläge, laddas ur eller är avstängd.
● Fast vitt sken - Kameran används. ● Av - Kameran används inte. Caps Lock-lampan: Anger om Caps Lock är aktiverat eller inaktiverat. ● Fast vitt sken – Caps Lock aktiverat. ● Av – Caps Lock inaktiverat. Återställ operativsystemet När datorn inte kan starta upp till operativsystemet även efter upprepade försök startar den automatiskt Dell SupportAssist OS Recovery.
Hur man kör M-BIST OBS: M-BIST måste initieras på systemet från ett avstängt strömtillstånd som antingen är anslutet till nätström eller endast med batteri. 1. Tryck och håll både M-tangenten på tangentbordet och strömknappen intryckt för att initiera M-BIST. 2. Om både M-tangenten och strömknappen hålls nedtryckt kan indikatorlampan för batteriet uppvisa två tillstånd: a. OFF: Inget fel upptäcks med moderkortet b.
4. Anslut nätadaptern till datorn. 5. Starta datorn.
6 Få hjälp och kontakta Dell Resurser för självhjälp Du kan få information och hjälp för Dell-produkter och tjänster med följande resurser för självhjälp: Tabell 9. Resurser för självhjälp Resurser för självhjälp Resursplats Information om Dell-produkter och tjänster www.dell.com My Dell Tips Kontakta support I Windows skriver du Contact Support och trycker på retur. Onlinehjälp för operativsystemet www.dell.com/support/windows www.dell.
Kontakta Dell OBS: Om du inte har en fungerande Internet-anslutning kan du hitta kontaktinformation på fakturan, följesedeln, räkningen och i Dells produktkatalog. Dell erbjuder flera alternativ för support och service online och på telefon. Tillgängligheten varierar beroende på land och produkt och vissa tjänster kanske inte finns i ditt område. Gör så här för att kontakta Dell för försäljningsärenden, teknisk support eller kundtjänst: 1. Gå till Dell.com/support. 2. Välj supportkategori. 3.