Users Guide
Table Of Contents
- Installation Guide
- Installationsanleitung
- Inhalt
- Zu diesem Handbuch
- PowerConnect W-3000 Serie Controller
- Installieren des W-3000 Serie Controller
- Technische Daten, Sicherheit und Konformität
- Guide d’installation
- Table des matières
- À propos de ce guide
- À propos des contrôleurs Dell PowerConnect Série W-3000
- Installation du contrôleur Série W-3000
- Spécifications, sécurité et conformité
- Guía de instalación
- Contenido
- Acerca de esta guía
- Acerca de los controladores PowerConnect Serie W-3000
- Instalación de los controladores Serie W-3000
- Especificaciones, seguridad y cumplimiento
- Guia de instalação
- Índice
- Sobre este guia
- Sobre os Controladores Série W-3000 PowerConnect
- Instalação dos Controladores Série W-3000
- Especificações, segurança e conformidade
- Kurulum Kılavuzu
- İçindekiler
- Bu Kılavuz Hakkında
- PowerConnect W-3000 Serisi Denetleyiciler Hakkında
- W-3000 Serisi Denetleyiciler Kurulumu
- Spesifikasyonlar, Güvenlik ve Uygunluk
- 設置ガイド
- 설치 안내서
- 安裝指南
- 安装指南
- Panduan Instalasi
- מדריך התקנה
![](/manual/dell/w-3200/users-guide-german/images/img-8.png)
Dell PowerConnect W-3000 Series Controller | Installation Guide About the PowerConnect W-3000 Series Controllers | 9
10/100/1000Base-T Gigabit Ethernet Ports
There are four 10/100/1000Base-T Gigabit Ethernet (RJ-45) ports. Gigabit Ethernet uses all eight wires and each
pair is used in a bi-directional fashion, meaning the same pairs are used for both data transmission and reception.
Figure 2 illustrates the CAT-5 pin-out found on an RJ-45 connector. The CAT-5 pin-out pairs the following pins
on a 10/100/1000Base-T Gigabit Ethernet port: 1/2, 3/6, 4/5, and 7/8.
Figure 2 Gigabit Ethernet Port Pin-Out
Serial Console Port
A serial console port is provided for connection to a terminal, allowing for direct local management. The port’s
RJ-45 female connector accepts an RS-232 serial cable with a male connector.
Figure 3 Serial Console Port Pin-Out
Communication settings for the serial console port are indicated in Table 1.
Serial Console Port Adaptor
A modular adaptor can be used to convert the RJ-45 (female) connector to a DB9 (male) connector. Refer to
Figure 4 for complete details.
Table 1 Console Terminal Settings
Baud Rate Data Bits Parity Stop Bits Flow Control
9600 8 None 1 None
1000Base-T Gigabit
Ethernet Port
RJ-45 Female
Pin-Out
Signal Name
1
2
3
4
5
6
7
8
BI_DC+
BI_DC-
BI_DD+
BI_DD-
BI_DA+
BI_DA-
BI_DB+
BI_DB-
Function
Bi-directional pair +C
Bi-directional pair -C
Bi-directional pair +D
Bi-directional pair -D
Bi-directional pair +A
Bi-directional pair -A
Bi-directional pair +B
Bi-directional pair -B
Serial
Console Port
1
2
3
4
5
6
7
8
TxD
GND
RxD
RJ-45 Female
Pin-Out
Direction
Input
Output
GND
Caution: Do not connect an Access Point (AP) to the serial console port. The serial console port is compatible with only RS-232
devices. Non-RS-232 devices, such as APs, are not supported.