Users Guide
Table Of Contents
- Dell PowerConnect ArubaOS 5.0
- Contents
- About this Guide
- The Basic User-Centric Networks
- Configuring the User-Centric Network
- Deployment and Configuration Tasks
- Configuring the Controller
- Configuring a VLAN for Network Connection
- Deploying APs
- Additional Configuration
- Network Parameters
- Configuring VLANs
- Configuring Ports
- About VLAN Assignments
- Assigning a Static Address to a VLAN
- Using CLI
- Configuring a VLAN to Receive a Dynamic Address
- Enabling the DHCP Client
- Enabling the PPPoE Client
- Default Gateway from DHCP/PPPoE
- Configuring DNS/WINS Server from DHPC/PPPoE
- Using the WebUI
- Configuring Source NAT to Dynamic VLAN Address
- Configuring Source NAT for VLAN Interfaces
- Inter-VLAN Routing
- Configuring Static Routes
- Configuring the Loopback IP Address
- Configuring the Controller IP Address
- Configuring GRE Tunnels
- RF Plan
- Supported Planning
- Before You Begin
- Launching the RF Plan
- Using the FQLN Mapper in the AP Provision Page
- RF Plan Example
- Sample Building
- Create a Building
- Model the Access Points
- Model the Air Monitors
- Add and Edit a Floor
- Adding the background image and naming the first floor
- Adding the background image and naming the second floor
- Defining Areas
- Creating a Don’t Care Area
- Creating a Don’t Deploy Area
- Running the AP Plan
- Running the AM Plan
- Access Points
- Remote AP vs Campus AP
- Basic Configuration
- AP Names and Groups
- Virtual APs
- Configuring Profiles
- Profile Hierarchy
- Virtual AP Configurations
- Configuring High-throughput on Virtual APs
- Advanced Configuration Options
- Automatic Channel and Transmit Power Selection Using ARM
- APs Over Low-Speed Links
- AP Redundancy
- AP Maintenance Mode
- Managing AP LEDs
- Adaptive Radio Management (ARM)
- Remote Access Points
- Overview
- Configuring the Secure Remote Access Point Service
- Deploying a Branch Office/Home Office Solution
- Enabling Double Encryption
- Advanced Configuration Options
- Understanding Remote AP Modes of Operation
- Fallback Mode
- Configuring the fallback mode
- Configuring the DHCP Server on the Remote AP
- Advanced Backup Configuration Options
- DNS Controller Setting
- Backup Controller List
- Remote AP Failback
- RAP Local Network Access
- Remote AP Authorization Profiles
- Access Control Lists and Firewall Policies
- Split Tunneling
- Configuring the Session ACL
- Configuring ACL for restricted LD homepage access
- Configuring the AAA Profile and the Virtual AP Profile
- Wi-Fi Multimedia
- Uplink Bandwidth Reservation
- Secure Enterprise Mesh
- Mesh Access Points
- Mesh Links
- Mesh Profiles
- Mesh Solutions
- Before You Begin
- Mesh Radio Profiles
- RF Management (802.11a and 802.11g) Profiles
- Mesh High-Throughput SSID Profiles
- Mesh Cluster Profiles
- Ethernet Ports for Mesh
- Provisioning Mesh Nodes
- AP Boot Sequence
- Verifying the Network
- Remote Mesh Portals
- Authentication Servers
- Important Points to Remember
- Servers and Server Groups
- Configuring Servers
- Internal Database
- Server Groups
- Assigning Server Groups
- Configuring Authentication Timers
- 802.1x Authentication
- Overview of 802.1x Authentication
- Configuring 802.1x Authentication
- Example Configurations
- Authentication with an 802.1x RADIUS Server
- Configuring Roles and Policies
- Configuring the RADIUS Authentication Server
- Configure 802.1x Authentication
- Configure VLANs
- Configuring the WLANs
- Configuring the Guest WLAN
- Configuring the Non-Guest WLANs
- Authentication with the Controller’s Internal Database
- Configuring the Internal Database
- Configure 802.1x Authentication
- Configure VLANs
- Configuring the WLANs
- Configuring the Guest WLAN
- Configuring the Non-Guest WLANs
- Advanced Configuration Options for 802.1x
- Roles and Policies
- Stateful and WISPr Authentication
- Captive Portal
- Captive Portal Overview
- Captive Portal in the Base ArubaOS
- Captive Portal with the PEFNG License
- Example Authentication with Captive Portal
- Creating a Guest-logon User Role
- Creating an Auth-guest User Role
- Configure Policies and Roles via the WebUI
- Time Range
- Auth-Guest-Access Policy
- Block-Internal-Access Policy
- Drop-and-Log Policy
- Guest-logon Role
- Guest-Logon Role
- Configure Policies and Roles via the CLI
- Time Range
- Create Aliases
- Guest-Logon-Access Policy
- Auth-Guest-Access Policy
- Block-Internal-Access Policy
- Drop-and-Log Policy
- Guest-Logon Role
- Auth-Guest Role
- Guest VLANs
- Captive Portal Authentication
- Optional Captive Portal Configurations
- Personalizing the Captive Portal Page
- Securing Client Traffic
- Securing Controller-to-Controller Communication
- Configuring the Odyssey Client on Client Machines
- Advanced Security
- Virtual Intranet Access
- VIA
- Configuring the VIA Controller
- VPN Configuration
- Remote Access VPN for L2TP IPsec
- Remote Access VPNs for XAuth
- Remote Access VPN for PPTP
- Site-to-Site VPNs
- Dell Dialer
- Virtual Private Networks
- MAC-based Authentication
- Control Plane Security
- Control Plane Security Overview
- Configuring Control Plane Security
- Whitelists on Master and Local Controllers
- Environments with Multiple Master Controllers
- Replacing a Controller on a Multi-Controller Network
- Troubleshooting Control Plane Security
- Adding Local Controllers
- IP Mobility
- VRRP
- RSTP
- W-600 Series Controller
- OSPFv2
- Wireless Intrusion Prevention
- IDS Features
- IDS Configuration
- WLAN Management System
- Client Blacklisting
- Link Aggregation Control Protocol
- Management Access
- Certificate Authentication for WebUI Access
- Public Key Authentication for SSH Access
- Radius Server Authentication
- Radius Server Username/Password Authentication
- RADIUS Server Authentication with VSA
- RADIUS Server Authentication with Server-Derivation Rule
- Disabling Authentication of Local Management User Accounts
- Verifying the configuration
- Resetting the Admin or Enable Password
- Setting an Administrator Session Timeout
- Management Password Policy
- Managed RFprotect Sensors
- Managing Certificates
- Configuring SNMP
- Configuring Logging
- Guest Provisioning
- Managing Files on the Controller
- Setting the System Clock
- Software Licenses
- IPv6 Client Support
- Voice and Video
- License Requirements
- Configuring Voice
- Configuring Video
- QoS
- External Services Interface
- Understanding ESI
- Understanding the ESI Syslog Parser
- ESI Configuration Overview
- Configuring Health-Check Method, Groups, and Servers
- Defining the ESI Server
- Defining the ESI Server Group
- Redirection Policies and User Role
- ESI Syslog Parser Domains and Rules
- Managing Syslog Parser Domains in the WebUI
- Managing Syslog Parser Domains in the CLI
- Managing Syslog Parser Rules
- Monitoring Syslog Parser Statistics
- Example Route-mode ESI Topology
- ESI server configuration on controller
- IP routing configuration on Fortinet gateway
- Configuring the Example Routed ESI Topology
- Health-Check Method, Groups, and Servers
- Defining the Ping Health-Check Method
- Defining the ESI Server
- Defining the ESI Server Group
- Redirection Policies and User Role
- Syslog Parser Domain and Rules
- Example NAT-mode ESI Topology
- Basic Regular Expression Syntax
- DHCP with Vendor-Specific Options
- External Firewall Configuration
- Behavior and Defaults
- 802.1x Configuration for IAS and Windows Clients
- Internal Captive Portal
- VIA End User Instructions
- Provisioning RAP at Home
- Index
482 | Wireless Intrusion Prevention Dell PowerConnect ArubaOS 5.0 | [User Guide
To enable AP learning via the command-line interface, access the CLI in config mode and issue the following
commands:
wms general learn-ap {enable|disable}
Classifying APs
If AP learning is enabled, non-Dell APs connected on the same wired network as Dell APs are classified as valid
APs. If AP learning is disabled, a non-Dell AP is classified as a rogue AP. You can also manually classify an AP. For
example, if you know about an interfering AP, you can manually reclassify it as a known interfering AP. You can
use the WebUI or CLI to manually classify an AP into one of the following categories:
To enable AP learning via the WebUI:
1. Navigate to the Reports > AP Reports> All Interfering APs page on the master controller.
2. Select the checkbox for the AP(s) you want to classify.
3. Click the appropriate Set as button on the page.
4. Click Apply.
To enable AP learning via the command-line interface, access the CLI in config mode and issue the following
commands:
Enter the following command in privilege mode:
wms ap <bssid> mode {dos|interfering|known-interfering|unsecure|valid}
Configuring Misconfigured AP Detection and Protection
An AP is classified as misconfigured if it does not meet any of the following configurable parameters:
z Valid channels
z Encryption type
z Short preamble
Table 101 AP Manual Classification Categories
AP Type Description
Valid AP An AP that is part of the enterprise providing WLAN service. Dell APs that successfully
connect to the controller and load software and configuration should be classified as
valid APs.
NOTE: Any client that successfully authenticates with a valid AP and passes encrypted
traffic is classified as a valid client. (Encrypted traffic includes encrypted 802.11 frames
and unencrypted 802.11 frames which are VPN encrypted.)
Interfering AP An AP that is seen in the RF environment but is not connected to the wired network. An
interfering AP is not considered a direct security threat since it is not connected to the
wired network. For example, an interfering AP can be an AP that belongs to a
neighboring office’s WLAN and is not part of your WLAN network.
Known Interfering AP An interfering AP where the BSSIDs are known. Once classified, a known interfering AP
does not change its state.
Unsecure AP (rogue AP) A rogue AP is an unauthorized AP that is plugged into the wired side of the network. You
can configure automatic shutdown of rogue APs in the IDS unauthorized device
detection profile.
Suspected Unsecure AP A suspected rogue AP is plugged into the wired side of the network, but may not be an
unauthorized device. Automatic rogue containment does not apply to suspected rogue
APs.
DoS AP An AP for which denial of service is enabled. Any clients connected to this AP are
disconnected.