Users Guide
Table Of Contents
- Dell PowerConnect ArubaOS 5.0
- Contents
- About this Guide
- The Basic User-Centric Networks
- Configuring the User-Centric Network
- Deployment and Configuration Tasks
- Configuring the Controller
- Configuring a VLAN for Network Connection
- Deploying APs
- Additional Configuration
- Network Parameters
- Configuring VLANs
- Configuring Ports
- About VLAN Assignments
- Assigning a Static Address to a VLAN
- Using CLI
- Configuring a VLAN to Receive a Dynamic Address
- Enabling the DHCP Client
- Enabling the PPPoE Client
- Default Gateway from DHCP/PPPoE
- Configuring DNS/WINS Server from DHPC/PPPoE
- Using the WebUI
- Configuring Source NAT to Dynamic VLAN Address
- Configuring Source NAT for VLAN Interfaces
- Inter-VLAN Routing
- Configuring Static Routes
- Configuring the Loopback IP Address
- Configuring the Controller IP Address
- Configuring GRE Tunnels
- RF Plan
- Supported Planning
- Before You Begin
- Launching the RF Plan
- Using the FQLN Mapper in the AP Provision Page
- RF Plan Example
- Sample Building
- Create a Building
- Model the Access Points
- Model the Air Monitors
- Add and Edit a Floor
- Adding the background image and naming the first floor
- Adding the background image and naming the second floor
- Defining Areas
- Creating a Don’t Care Area
- Creating a Don’t Deploy Area
- Running the AP Plan
- Running the AM Plan
- Access Points
- Remote AP vs Campus AP
- Basic Configuration
- AP Names and Groups
- Virtual APs
- Configuring Profiles
- Profile Hierarchy
- Virtual AP Configurations
- Configuring High-throughput on Virtual APs
- Advanced Configuration Options
- Automatic Channel and Transmit Power Selection Using ARM
- APs Over Low-Speed Links
- AP Redundancy
- AP Maintenance Mode
- Managing AP LEDs
- Adaptive Radio Management (ARM)
- Remote Access Points
- Overview
- Configuring the Secure Remote Access Point Service
- Deploying a Branch Office/Home Office Solution
- Enabling Double Encryption
- Advanced Configuration Options
- Understanding Remote AP Modes of Operation
- Fallback Mode
- Configuring the fallback mode
- Configuring the DHCP Server on the Remote AP
- Advanced Backup Configuration Options
- DNS Controller Setting
- Backup Controller List
- Remote AP Failback
- RAP Local Network Access
- Remote AP Authorization Profiles
- Access Control Lists and Firewall Policies
- Split Tunneling
- Configuring the Session ACL
- Configuring ACL for restricted LD homepage access
- Configuring the AAA Profile and the Virtual AP Profile
- Wi-Fi Multimedia
- Uplink Bandwidth Reservation
- Secure Enterprise Mesh
- Mesh Access Points
- Mesh Links
- Mesh Profiles
- Mesh Solutions
- Before You Begin
- Mesh Radio Profiles
- RF Management (802.11a and 802.11g) Profiles
- Mesh High-Throughput SSID Profiles
- Mesh Cluster Profiles
- Ethernet Ports for Mesh
- Provisioning Mesh Nodes
- AP Boot Sequence
- Verifying the Network
- Remote Mesh Portals
- Authentication Servers
- Important Points to Remember
- Servers and Server Groups
- Configuring Servers
- Internal Database
- Server Groups
- Assigning Server Groups
- Configuring Authentication Timers
- 802.1x Authentication
- Overview of 802.1x Authentication
- Configuring 802.1x Authentication
- Example Configurations
- Authentication with an 802.1x RADIUS Server
- Configuring Roles and Policies
- Configuring the RADIUS Authentication Server
- Configure 802.1x Authentication
- Configure VLANs
- Configuring the WLANs
- Configuring the Guest WLAN
- Configuring the Non-Guest WLANs
- Authentication with the Controller’s Internal Database
- Configuring the Internal Database
- Configure 802.1x Authentication
- Configure VLANs
- Configuring the WLANs
- Configuring the Guest WLAN
- Configuring the Non-Guest WLANs
- Advanced Configuration Options for 802.1x
- Roles and Policies
- Stateful and WISPr Authentication
- Captive Portal
- Captive Portal Overview
- Captive Portal in the Base ArubaOS
- Captive Portal with the PEFNG License
- Example Authentication with Captive Portal
- Creating a Guest-logon User Role
- Creating an Auth-guest User Role
- Configure Policies and Roles via the WebUI
- Time Range
- Auth-Guest-Access Policy
- Block-Internal-Access Policy
- Drop-and-Log Policy
- Guest-logon Role
- Guest-Logon Role
- Configure Policies and Roles via the CLI
- Time Range
- Create Aliases
- Guest-Logon-Access Policy
- Auth-Guest-Access Policy
- Block-Internal-Access Policy
- Drop-and-Log Policy
- Guest-Logon Role
- Auth-Guest Role
- Guest VLANs
- Captive Portal Authentication
- Optional Captive Portal Configurations
- Personalizing the Captive Portal Page
- Securing Client Traffic
- Securing Controller-to-Controller Communication
- Configuring the Odyssey Client on Client Machines
- Advanced Security
- Virtual Intranet Access
- VIA
- Configuring the VIA Controller
- VPN Configuration
- Remote Access VPN for L2TP IPsec
- Remote Access VPNs for XAuth
- Remote Access VPN for PPTP
- Site-to-Site VPNs
- Dell Dialer
- Virtual Private Networks
- MAC-based Authentication
- Control Plane Security
- Control Plane Security Overview
- Configuring Control Plane Security
- Whitelists on Master and Local Controllers
- Environments with Multiple Master Controllers
- Replacing a Controller on a Multi-Controller Network
- Troubleshooting Control Plane Security
- Adding Local Controllers
- IP Mobility
- VRRP
- RSTP
- W-600 Series Controller
- OSPFv2
- Wireless Intrusion Prevention
- IDS Features
- IDS Configuration
- WLAN Management System
- Client Blacklisting
- Link Aggregation Control Protocol
- Management Access
- Certificate Authentication for WebUI Access
- Public Key Authentication for SSH Access
- Radius Server Authentication
- Radius Server Username/Password Authentication
- RADIUS Server Authentication with VSA
- RADIUS Server Authentication with Server-Derivation Rule
- Disabling Authentication of Local Management User Accounts
- Verifying the configuration
- Resetting the Admin or Enable Password
- Setting an Administrator Session Timeout
- Management Password Policy
- Managed RFprotect Sensors
- Managing Certificates
- Configuring SNMP
- Configuring Logging
- Guest Provisioning
- Managing Files on the Controller
- Setting the System Clock
- Software Licenses
- IPv6 Client Support
- Voice and Video
- License Requirements
- Configuring Voice
- Configuring Video
- QoS
- External Services Interface
- Understanding ESI
- Understanding the ESI Syslog Parser
- ESI Configuration Overview
- Configuring Health-Check Method, Groups, and Servers
- Defining the ESI Server
- Defining the ESI Server Group
- Redirection Policies and User Role
- ESI Syslog Parser Domains and Rules
- Managing Syslog Parser Domains in the WebUI
- Managing Syslog Parser Domains in the CLI
- Managing Syslog Parser Rules
- Monitoring Syslog Parser Statistics
- Example Route-mode ESI Topology
- ESI server configuration on controller
- IP routing configuration on Fortinet gateway
- Configuring the Example Routed ESI Topology
- Health-Check Method, Groups, and Servers
- Defining the Ping Health-Check Method
- Defining the ESI Server
- Defining the ESI Server Group
- Redirection Policies and User Role
- Syslog Parser Domain and Rules
- Example NAT-mode ESI Topology
- Basic Regular Expression Syntax
- DHCP with Vendor-Specific Options
- External Firewall Configuration
- Behavior and Defaults
- 802.1x Configuration for IAS and Windows Clients
- Internal Captive Portal
- VIA End User Instructions
- Provisioning RAP at Home
- Index
538 | IPv6 Client Support Dell PowerConnect ArubaOS 5.0 | [User Guide
The following examples configure attack rates and the session timeout for IPv6 traffic.
To configure the firewall function via the WebUI:
1. Navigate to the Configuration > Advanced Services > Stateful Firewall > Global Setting page.
2. Under the IPv6 column, enter the following:
z For Monitor Ping Attack, enter 15
z For Monitor IP Session Attack, enter 25
z For Session Idle Timeout, enter 60
3. Click Apply.
Deny Inter User Bridging Prevents the forwarding of Layer-2 traffic between wired or wireless users. You can configure user
role policies that prevent Layer-3 traffic between users or networks but this does not block Layer-2
traffic. This option can be used to prevent traffic, such as Appletalk or IPX, from being forwarded.
Default: Disabled
Deny All IP Fragments Drops all IP fragments.
NOTE: Do not enable this option unless instructed to do so by an Dell representative.
Default: Disabled
Enforce TCP Handshake
Before Allowing Data
Prevents data from passing between two clients until the three-way TCP handshake has been
performed. This option should be disabled when you have mobile clients on the network as
enabling this option will cause mobility to fail. You can enable this option if there are no mobile
clients on the network.
Default: Disabled
Prohibit IP Spoofing Enables detection of IP spoofing (where an intruder sends messages using the IP address of a
trusted client). When this option is enabled, IP and MAC addresses are checked for each ARP
request/response. Traffic from a second MAC address using a specific IP address is denied, and
the entry is not added to the user table. Possible IP spoofing attacks are logged and an SNMP trap
is sent.
Default: Disabled
NOTE: An IPv6 client can have multiple IP addresses. Enabling IP spoofing on the controller can
cause IPv6 clients to lose network access.
Prohibit RST Replay Attack When enabled, closes a TCP connection in both directions if a TCP RST is received from either
direction. You should not enable this option unless instructed to do so by an Dell representative.
Default: Disabled
Session Mirror Destination Destination (IPv4 address or controller port) to which mirrored session packets are sent. You can
configure IPv6 flows to be mirrored with the session ACL “mirror” option.This option is used only
for troubleshooting or debugging.
Default: N/A
Session Idle Timeout Set the time, in seconds, that a non-TCP session can be idle before it is removed from the session
table. Specify a value in the range 16–259 seconds. You should not set this option unless instructed
to do so by an Dell representative.
Default: 30 seconds
Per-packet Logging Enables logging of every packet if logging is enabled for the corresponding session rule. Normally,
one event is logged per session. If you enable this option, each packet in the session is logged. You
should not enable this option unless instructed to do so by an Dell representative, as doing so may
create unnecessary overhead on the controller.
Default: Disabled (per-session logging is performed)
Table 116 IPv6 Firewall Parameters (Continued)
Authentication
Method
Description