Dell Networking W-Series Instant 6.4.2.0-4.1.
Copyright © 2014 Aruba Networks, Inc. Aruba Networks trademarks include , Aruba Networks®, Aruba ® Wireless Networks , the registered Aruba the Mobile Edge Company logo, and Aruba Mobility Management System®. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc. All rights reserved. Specifications in this manual are subject to change without notice. Originated in the USA. All other trademarks are the property of their respective owners.
Chapter 1 About this Guide This document describes the Instant command syntax and provides the following information for each command: l Command Syntax—The complete syntax of the command. l Description—A brief description of the command. l Syntax—A description of the command parameters, the applicable ranges and default values, if any. l Usage Guidelines—Information to help you use the command, including prerequisites, prohibitions, and related commands.
Table 1: Typographical Conventions Type Style Description Italics This style is used for emphasizing important terms and to mark the titles of books. Boldface This style is used for command names and parameter options when mentioned in the text. Commands This fixed-width font depicts command syntax and examples of commands and command output.
Contacting Dell Table 2: Support Information Support Main Website dell.com Contact Information dell.com/contactdell Support Website dell.com/support Documentation Website dell.com/support/manuals Dell Networking W-Series Instant 6.4.2.0-4.1.
What is New in Instant 6.4.0.2-4.1.1 This section lists the new and modified commands in the Instant 6.4.0.2-4.1.1 release. New Commands There are no new commands introduced in this release. Modified Commands The following commands are modified in the Instant 6.4.0.2-4.1.1 release: Table 3: Modified Commands in 6.4.0.2-4.1.1 Command Description wlan ssid-profile This command now enables configuring an accounting server for the specified SSID to perform accounting functions.
Chapter 2 Instant CLI Instant supports the use of Command Line Interface (CLI) for scripting purposes. You can access the Instant CLI through a Secure Shell (SSH). To enable the SSH access to the Instant CLI: 1. From the Instant UI, navigate to System > Show advanced options. 2. Select Enabled from the Terminal access drop-down list. 3. Click OK. Connecting to a CLI Session On connecting to a CLI session, the system displays its host name followed by the login prompt.
(Instant AP)# commit apply To apply the configuration changes to the cluster, without saving the configuration, use the following command in the privileged mode: (Instant AP)# commit apply no-save To view the changes that are yet to be applied, use the following command in the privileged mode: (Instant AP)# show uncommitted-config To revert to the earlier configuration, use the following command in the privileged mode.
Using Sequence Sensitive Commands The Instant CLI does not support positioning or precedence of sequence-sensitive commands. Therefore, it is recommended that you remove the existing configuration before adding or modifying the configuration details for sequence-sensitive commands. You can either delete an existing profile or remove a specific configuration by using the no… commands. The following table lists the sequence-sensitive commands and the corresponding no command to remove the configuration.
Command Line Editing The system records your most recently entered commands. You can review the history of your actions, or reissue a recent command easily, without having to retype it. To view items in the command history, use the up arrow key to move back through the list and the down arrow key to move forward. To reissue a specific command, press Enter when the command appears in the command history. You can also use the command line editing feature to make changes to the command prior to entering it.
Specifying Addresses and Identifiers in Commands This section describes addresses and other identifiers that you can reference in CLI commands. Table 6: Addresses and Identifiers Address/Identifier Description IP address For any command that requires entry of an IP address to specify a network entity, use IPv4 network address format in the conventional dotted decimal notation (for example, 192.0.2.1).
a-channel a-channel Description This command configures 5 GHz radio channels for a specific W-IAP. Syntax Parameter Description Range Configures the specified 5 GHz channel. The valid channels for a band are determined by the AP regulatory domain. Configures the specified transmission power values. 0-127 dBm Usage Guidelines Use this command to configure radio channels for the 5 GHz band for a specific W-IAP.
a-external-antenna a-external-antenna Description This command configures external antenna connectors for a W-IAP. Syntax Parameter Description Range Configures the antenna gain. You can configure a gain value in dBi for the following types of antenna: Diploe/Omni - 6 l Dipole/Omni l Panel l Sector Panel -14 Sector - 14 Usage Guidelines If your W-IAP has external antenna connectors, you need to configure the transmit power of the system.
(Instant AP)# a-external-antenna 14 Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
aaa test-server aaa test-server Description This command tests a configured authentication server. Syntax Parameter Description Allows you to specify the authentication server for which the authentication test is run. Allows you to specify the user name for which the authentication test is run. Usage Guidelines Use this command to view the CPU load for application and system processes.
aeroscout-rtls aeroscout-rtls [include-unassoc-sta] no... Description This command configures the Aeroscout Real-Time Asset Location Server (RTLS) settings for Instant and sends the Radio-frequency identification (RFID) tag information to an Aeroscout RTLS server. Syntax Command/Parameter Description Default IP address of the Aeroscout RTLS server to which the location reports are sent.
airgroup airgroup cppm enforce-registration cppm-query-interval cppm-server disable enable [dlna-only| mdns-only] enable-guest-multicast multi-swarm no… Description This command configures the AirGroup settings on a W-IAP. Syntax Parameter Description cppm enforce-registration Enforces the discovery of the CPPM registered devices. When enabled, only devices registered with CPPM will be discovered by Bonjour® or DLNA devices, based on the CPPM policy configured.
Parameter Description Range Default VLAN. multi-swarm Enables inter cluster mobility. When enabled, the W-IAP shares the mDNS database information with the other clusters. The AirGroup records in the Virtual Controller can be shared with all the Virtual Controllers specified for L3 Mobility. — Disabled no… Removes the specified configuration parameter.
airgroupservice airgroupservice description disable disallow-role disallow-vlan enable id no… Description This command configures the availability of AirGroup services for the W-IAP clients. Syntax Parameter Description Default Specifies the AirGroup service to configure.
Parameter Description Default You can allow all services or add custom services. Up to 10 services can be configured on a W-IAP. description Adds a description to the AirGroup service profile. — disable Disables AirGroup services for the profile. — disallow-role Restricts the user roles specified for role from accessing the AirGroup service. Disabled disallow-vlan Restricts the AirGroup servers connected on the specified VLANs from being discovered.
Command Information W-IAP Platform Command Mode All platforms Configuration mode and AirGroup services configuration submode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
airwave-rtls airwave-rtls [include-unassoc-sta] no… Description This command integrates W-AirWave Real-Time Asset Location Server (RTLS) settings for Instant and sends the Radio-frequency identification (RFID) tag information to a W-AirWave RTLS server with the RTLS feed to accurately locate the wireless clients. Syntax Command/Parameter Description Default Configures the IP address of the W-AirWave RTLS server.
ale-report-interval ale-report-interval no… Description This command configures the interval at which a W-IAP sends data to the Analytics and Location Engine (ALE) server. Syntax Command/Parameter Description Range Default ale-report-interval Configures an interval at which the Virtual Controller can report the W-IAP and client details to the ALE server. 6–60 seconds 30 no… Removes the specified configuration parameter.
ale-server ale-server no… Description This command configures Analytics and Location Engine (ALE) server details for W-IAP integration with ALE. Syntax Command/Parameter Description ale-server Allows you to specify the Fully Qualified Domain Name (FQDN) or IP address of the ALE server. no… Removes the specified configuration parameter. Usage Guidelines Use this command to enable a W-IAP for ALE support.
alg alg sccp-disable sip-disable vocera-disable no… Description This command allows you to modify the configuration settings for Application Layer Gateway (ALG) protocols enabled on a W-IAP. An application-level gateway consists of a security component that augments a firewall or NAT used in a network. Syntax Command/Parameter Description Default sccp-disable Disables the Skinny Call Control Protocol (SCCP).
allow-new-aps allow-new-aps no… Description This command allows the new access points to join the W-IAP cluster. Syntax Command/Parameter Description allow-new-aps Allows new access points in the domain. no Removes the specified configuration parameter. Usage Guidelines Use this command to allow the new access points to join the W-IAP cluster. Example The following command allows the new W-IAPs to join the cluster.
allowed-ap allowed-ap no… Description This command allows an AP to join the W-IAP cluster. Syntax Command/Parameter Description allowed-ap Specifies the MAC address of the W-IAP that is allowed to join the cluster. no… Removes the specified configuration parameter. Usage Guidelines Use this command to allow a W-IAP to join the cluster.
ams-backup-ip ams-backup-ip no… Description This command adds the IP address or domain name of the backup W-AirWave Management server. Syntax Parameter Description Configures the IP address or domain name of the secondary W-AirWave Management Server. no… Removes the specified configuration parameter. Usage Guidelines Use this command to add the IP address or domain name of the backup W-AirWave Management Server.
ams-identity ams-identity Description This command uniquely identifies the group of W-IAPs managed or monitored by the W-AirWave Management console. The name can be a location, vendor, department, or any other identifier. Syntax Parameter Description ams-identity Configures a name that uniquely identifies the W-IAP on the WAirWave Management server. The name defined for this command will be displayed under the Groups tab in the W-AirWave user interface.
ams-ip ams-ip no… Description This command configures the IP address or domain name of the W-AirWave Management console for a W-IAP. Syntax Parameter Description Configures the IP address or domain name of anW-AirWave Management server for a W-IAP. Usage Guidelines Use this command to configure the IP address or domain name of the AMS console for a W-IAP. Example The following command configures the W-AirWave Server.
ams-key ams-key no… Description This command assigns a shared key for service authorization. Syntax Parameter Description Authorizes the first Virtual Controller to communicate with the W-AirWave server. no… Removes the specified configuration parameter. Usage Guidelines Use this command to assign a shared key for service authorization. This shared key is used for configuring the first AP in the W-IAP network.
apply apply {cplogo-install| cplogo-uninstall| debug-command| delta-config} Description This command is used to save or apply the configuration settings on the W-IAP. Syntax Parameter Description cplogo-install Installs the Captive Portal logo on the W-IAP. cplogo-uninstall Uninstalls the Captive Portal logo on the W-IAP. debug-command Applies the configuration settings from the debug command. delta-config Applies the configuration settings from the delta-config command.
arm arm 80mhz-support a-channels air-time-fairness-mode {| | } band-steering-mode {balance-bands|prefer-5ghz| force-5ghz| disable} client-aware client-match [calc-interval | calc-threshold | debug | holdtime | max-adoption | max-request |nb-matching | slb-mode g-channels max-tx-power min-tx-power scanning wide-bands {| | <2.
Command/Parameter Description Range Default band-steering-mode Assigns the dual-band capable clients to the 5 GHz band on dual-band. It reduces co-channel interference and increases available bandwidth for dual-band clients, because there are more channels on the 5 GHz band than on the 2.4 GHz band.
Command/Parameter Description Range Default calc-interval Configures an interval at which client match is calculated. 10-600 30 seconds calc-threshold Configures a threshold that takes acceptance client count difference among all the channels of Client match into account. When the client load on an AP reaches or exceeds the threshold in comparison, client match is enabled on that AP. 1-255 2 debug Displays information required for debugging client match issues.
Command/Parameter Description Range Default the AP. If the maximum transmission EIRP configured on an AP is not supported by the AP model, the value is reduced to the highest supported power setting. NOTE: Higher power level settings may be constrained by local regulatory requirements and AP capabilities. scanning Allows the W-IAPs to scan other channels for RF Management and Wireless Intrusion Protection System enforcement. — Disabled wide-bands {| | <2.
Command History Version Description Dell Networking W-Series Instant 6.3.1.1-4.0 This command is modified. Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Configuration and ARM configuration sub-mode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
attack attack drop-bad-arp-enable fix-dhcp-enable no… poison-check-enable Description This command enables firewall settings to protect the network against wired attacks, such as ARP attacks or malformed DHCP packets, and notify the administrator when these attacks are detected. Syntax Command/Parameter Description drop-bad-arp-enable Enables the W-IAP to block the bad ARP request. fix-dhcp-enable Enables the W-IAP to fix the malformed DHCP packets.
auth-failure-blacklist-time auth-failure-blacklist-time Description This command allows the W-IAPs to dynamically blacklist the clients when they exceed the authentication failure threshold. Syntax Parameter Description Default auth-failure-blacklisttime Configures the duration in seconds for which the clients that exceed the maximum authentication failure threshold are blacklisted.
auth-survivability cache-time-out auth-survivability cache-time-out Description This command configures an interval after which the authenticated credentials of the clients stored in the cache expire. When the cache expires, the clients are required to authenticate again. Syntax Parameter Description Range Default auth-survivability cache-time-out Indicates the duration after which the authenticated credentials in the cache expire.
blacklist-client blacklist-client no… Description This command allows you to manually blacklist the clients by using MAC addresses of the clients. Syntax Parameter Description blacklist-client Adds the MAC address of the client to the blacklist. no… Removes the specified configuration parameter. Usage Guidelines Use this command to blacklist the MAC addresses of clients.
blacklist-time blacklist-time Description This command sets the duration in seconds for which the clients can be blacklisted due to an ACL rule trigger. Syntax Parameter Description Default blacklist-time Sets the duration in seconds for blacklisting clients due to an ACL rule trigger. 3600 Usage Guidelines Use this command to configure the duration in seconds for which the clients can be blacklisted when the blacklisting rule is triggered.
calea calea encapsulation-type ip ip mtu gre-type no... Description This command creates a Communications Assistance for Law Enforcement Act (CALEA) profile to enable W-IAPs for Lawful Intercept (LI) compliance and CALEA integration. Syntax Command/Parameter Description Range Default calea Enables calea configuration sub-mode for CALEA profile configuration.
Command History Version Description Dell Networking W-Series Instant 6.2.1.03.4 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Configuration mode and access rule configuration sub-mode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
cellular-uplink-profile cellular-uplink-profile 4g-usb-type <4G-usb-type> modem-isp modem-country usb-auth-type usb-dev usb-dial usb-init usb-modeswitch usb-passwd usb-tty usb-type usb-user modem-isp modem-country no… Description This command provisions the cellular (3G/4G) uplink profiles on a W-IAP.
Parameter Description Range Default usb-type Configures the driver type for the 3G modem. acm, airprime, hso, option, pantech-3g, sierra-evdo, sierragsm,none — usb-tty Specifies the modem tty port. — — usb-user Specifies the username of subscriber of the selected ISP. — — no… Removes the specified configuration parameter. — — Usage Guidelines Use this command to configure a cellular uplink profile on a W-IAP and modem parameters 3G /4G uplink provisioning.
l NTT DoCoMo L-02A l ZTE WCDMA Technologies MSM (MF668?) l Fivespot (ZTE) l c-motech CNU-600 l ZTE AC2736 l SEC-8089 (EpiValley) l Nokia CS-10 l NTT DoCoMo L-08C (LG) l NTT DoCoMo L-02C (LG) l Novatel MC545 l Huawei E220 for Movistar in Spain l Huawei E180 for Movistar in Spain l ZTE-MF820 l Huawei E173s-1 l Sierra 320 l Longcheer WM72 l U600 (3G mode) l Sierra USB-306 (HK CLS/1010 (HK)) l Sierra 306/308 (Telstra (Aus)) l Sierra 503 PCIe (Telstra (Aus)) l Sierra 312
l ZTE MF637 (Orange in Israel) l Huawei E180, E1692,E1762 (Optus (Aus)) l Huawei E1731 (Airtel-3G (India)) l Huawei E3765 (Vodafone (Aus)) l Huawei E3765 (T-Mobile (Germany) l Huawei E1552 (SingTel) l Huawei E1750 (T-Mobile (Germany)) l UGM 1831 (TMobile) l Huawei D33HW (EMOBILE(Japan)) l Huawei GD01 (EMOBILE(Japan)) l Huawei EC150 (Reliance NetConnect+ (India)) l KDDI DATA07(Huawei) (KDDI (Japan)) l Huawei E353 (China Unicom) l Huawei EC167 (China Telecom) l Huawei E367 (Vodafo
l Fraklin Wireless u770 l Huawei 3276s-150 l MC551L l Pantech UML295 l Pantech UML290 When UML290 runs in auto detect mode, the modem can switch from 4G network to 3G network or viceversa based on the signal strength. To configure the UML290 for the 3G network only, manually set the USB type to pantech-3g. To configure the UML290 for the 4G network only, manually set the 4G USB type to pantech-lte.
clear clear ap arp client datapath {session-all| statistics} Description This command clears various user-configured values from the running configuration on a W-IAP. Syntax Parameter Description ap Clears all W-IAP related information. arp Clears all ARP table information for a W-IAP. client Clears all information pertaining to a W-IAP client.
clear airgroup state statistics clear airgroup state statistics Description This command removes the AirGroup statistics. Usage Guidelines Use this command to remove AirGroup details from the W-IAP database. Example The following command clears AirGroup statistics: (Instant AP)(config)# clear airgroup state statistics Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced.
clear-cert clear-cert {ca|cp|server} Description This command clears client and server certificates from the W-IAP database. Syntax Parameter Description ca Clears all certificates uploaded on the W-IAP. cp Clears the captive portal server certificate uploaded on the W-IAP server Clears all server certificates. Usage Guidelines Use this command to clear the certificates from the W-IAP database.
clock set clock set
clock summer-time clock summer-time recurring no… Description This command configures daylight saving for the time zones that support daylight saving time. Syntax Parameter Description Range clock summer-time Configures Daylight Saving time. Timezones that support daylight saving configuration recurring Indicates the recurrences.
Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Configuration mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
clock timezone clock timezone no… Description This command sets the timezone on a W-IAP. Syntax Parameter Description Range clock timezone Configures the required timezone. All supported timezones Specifies the hours offset from the Universal Time Clock (UTC). — Specifies the hours offset from the Universal Time Clock (UTC). — no… Removes the timezone configuration.
commit commit {apply [no-save]| revert} Description This command allows you to commit configuration changes performed during a user session. You can also revert the changes that are already committed. Syntax Parameter Description apply Applies and saves the W-IAP configuration changes. no-save Applies the configuration changes to the cluster, but does not save the configuration. To save the configuration, run the write memory or commit apply command.
0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
configure terminal configure terminal Description This command allows you to enter configuration commands. Syntax No parameters. Usage Guidelines Upon entering this command, the enable mode prompt changes to: (Instant AP)(config)# To return to EXEC mode, enter Ctrl-Z, end or exit. Example The following command allows you to enter configuration commands: (Instant AP) # configure terminal Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced.
console console enable disable Description This command enables console access to a W-IAP through the serial port. Syntax Command/Parameter Description console Allows you to enter the console configuration mode. enable Enables console access to the W-IAP. disable Disables console access to the W-IAP. Usage Guidelines Use this command to enable or disable access to the W-IAP console and thus allow users to configure W-IAP settings or debug system errors.
content-filtering content-filtering no… Description This command enables content filtering feature. When content filtering is enabled on an SSID, all DNS requests to non-corporate domains on this wireless network are sent to OpenDNS. Syntax Command/Parameter Description content-filtering Enables content filtering. no Removes the configuration. Usage Guidelines Use this command to enable content filter.
convert-aos-ap convert-aos-ap Description This command allows you to provision a W-IAP as a Campus AP or Remote AP in a controller-based network, or as a standalone AP. Syntax Parameter Description Range Provisions the W-IAP as remote AP or campus AP in a controller-based network. W-IAP, CAP. Allows you to specify the IP address of the controller to which the Remote AP or Campus AP will be connected.
copy copy {config tftp |core-file tftp | flash tftp | tftp {cpserver cert format {p12|pem} | portal logo | system {1xca [format {der|pem}]|1xcert [format {p12|pem}]|config|flash}} Description This command copies files to and from the W-IAP. Syntax Parameter Description config Copies a configuration file to the TFTP server. core-file Copies a core file to the TFTP server.
Example The following example copies a configuration file to the TFTP server: (Instant AP)# copy config tftp 10.0.0.1 filename.cfg Command History Version Description Dell Networking W-Series Instant 6.3.1.1-4.0 This command was modified. Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
deny-inter-user-bridging deny-inter-user-bridging no… Description This command disables bridging traffic between two clients of a W-IAP on the same VLAN. Bridging traffic between the clients will be sent to the upstream device to make the forwarding decision. Syntax Parameter Description deny-inter-user-bridging Prevents the inter-user bridging. no… Removes the configuration. Usage Guidelines Use this command if you have security and traffic management policies defined for upstream devices.
deny-local-routing deny-local-routing no… Description This command disables routing traffic between two clients of a W-IAP on different VLANs. Routing traffic between the clients will be sent to the upstream device to make the forwarding decision. Syntax Parameter Description deny-local-routing Disables local routing of traffic. no… Removes the configuration.
device-id device-id Description This command assigns an ID for the AP device. Syntax Parameter Description device-id Configures an ID for the W-IAP device. Usage Guidelines Use this command to configure a device identification. Example The following example configures a device ID: (Instant AP)(config)# device-ID Device1 (Instant AP)(config)# end (Instant AP)# commit apply Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced.
disable-prov-ssid disable-prov-ssid no… Description This command disables the default provisioning SSID enabled in the W-IAP factory default settings. Usage Guidelines The default provisioning SSID is used during the initial configuration of the W-IAP if the automatic provisioning of the W-IAP fails and if W-AirWave is not reachable.
disconnect-user disconnect-user {|all|mac | network } Description This command disconnects the clients from a W-IAP. Syntax Parameter Description Allows you to disconnect a client by specifying the IP address of the client. all Disconnects all users associated with a W-IAP. mac Allows you to disconnect a client by specifying the MAC address of the client. network Allows you to disconnect the clients connected to a specific network.
download-cert download-cert {ca|cp|server} Description This command allows you to download the client, authentication server, and captive portal server certificates from an FTP or TFTP server, or by using an HTTP URL. Syntax Parameter Description ca Downloads client certificates. cp Downloads captive portal server certificates. server Downloads Server certificates. Allows you to specify the FTP, TFTP, or HTTP URL. Usage Guidelines Use this command to download certificates.
dpi dpi no… Description This command enables visualization of traffic from wired and wireless clients associated with a W-IAP. Syntax Parameter Description dpi Enables AppRF visualization. no… Removes the configuration. Usage Guidelines Use this command to enable AppRF visibility for wired and wireless clients associated with a W-IAP. AppRF supports an application and web-filtering service that allows creating firewall policies based on types of application.
dynamic-cpu-mgmt dynamic-cpu-mgmt {auto| disable| enable} Description This command enables or disables the dynamic CPU management feature, to manage resources across different functions performed by a W-IAP. Syntax Parameter Description auto Configures the W-IAP to automatically enable or disable CPU management feature during run-time.
dynamic-radius-proxy dynamic-radius-proxy no… Description This command enables the use of IP Address of the Virtual Controller for communication with external RADIUS servers. Syntax Command/Parameter Description dynamic-radius-proxy Enables dynamic RADIUS proxy feature to allow the Virtual Controller network to use the IP address of the Virtual Controller when communicating with the external RADIUS servers. no… Removes the configuration.
enet-vlan enet-vlan no… Description This command configures a VLAN for Ethernet connections. Syntax Parameter Description Range Default enet-vlan Configures VLAN for the upstream switch to which the AP is connected. 0–4093 1 no… Removes the configuration. — — Usage Guidelines Use this command to configure VLAN settings for upstream switch to which the AP is connected. By default, the value is set to 1.
enet0-bridging enet0-bridging Description This command allows you to use all ports on the APs as downlink ports. Usage Guidelines Use this command for W-IAP models that have only one Ethernet port enabled. When Eth0 bridging is configured, ensure that the uplink for each W-IAP is mesh link, Wi-Fi, or 3G/4G. Example The following command enables Eth0 bridging: (Instant AP)# enet0-bridging Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced.
enet0-port-profile enet0-port-profile Description This command assigns a wired profile to the Ethernet 0 port on a W-IAP. Syntax Parameter Description enet0-port-profile Assigns a wired profile to the Ethernet 0 interface port. Usage Guidelines Use this command to assign a wired profile to the Ethernet 0 port to activate the wired profile.
enet1-port-profile enet1-port-profile Description This command assigns a wired profile to the Ethernet 1 port on a W-IAP. Syntax Parameter Description enet1-port-profile Assigns a wired profile to the Ethernet 1 interface port. Usage Guidelines Use this command to assign a wired profile to the Ethernet 1 port to activate the wired profile.
enet2-port-profile enet2-port-profile Description This command assigns a wired profile to the Ethernet 2 port on a W-IAP. Syntax Parameter Description enet2-port-profile Assigns a wired profile to the Ethernet 2 interface port. Usage Guidelines Use this command to assign a wired profile to the Ethernet 2 port to activate the wired profile.
enet3-port-profile enet3-port-profile Description This command assigns a wired profile to the Ethernet 3 port on a W-IAP. Syntax Parameter Description enet3-port-profile Assigns a wired profile to the Ethernet 3 interface port. Usage Guidelines Use this command to assign a wired profile to the Ethernet 3 port to activate the wired profile.
enet4-port-profile enet4-port-profile Description This command assigns a wired profile to the Ethernet 4 port on a W-IAP. Syntax Parameter Description enet4-port-profile Assigns a wired profile to the Ethernet 4 interface port. Usage Guidelines Use this command to assign a wired profile to the Ethernet 4 port to activate the wired profile.
extended-ssid extended-ssid no… Description This command enables the configuration of additional WLAN SSIDs. Extended SSID is enabled by default in the factory default settings of Instant APs. Disabling the extended ssid option in the factory default mode will not take effect. Syntax Command/Parameter Description extended-ssid Enables the users to configure additional SSIDs. no… Removes the configuration. Usage Guidelines Use this command to create additional SSIDs.
factory-ssid-enable factory-ssid-enable Description This command resets the W-IAP to use the factory configuration. Syntax Parameter Description factory-ssid-enable Enables factory SSID configuration. Usage Guidelines Use this command to reset a W-IAP to use the factory default SSID.
firewall-external-enforcement firewall-external-enforcement pan disable enable ip
port user no… Description This command configures external firewall details such as Palo Alto Networks (PAN) firewall to enable integration with the W-IAP. Syntax Parameter Description Range Default firewall-external-enforcement pan PAN firewall configuration sub-mode. — — disable Disables PAN firewall. — — enable Enables PAN firewall.(Instant AP)(firewall-external-enforcement pan)# user admin1 admin1 (Instant AP)(firewall-external-enforcement pan)# end (Instant AP)# commit apply Command History Version Description Dell Networking W-Series Instant 6.3.1.14.0 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Configuration mode and firewall-external-enforcement submode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
g-channel g-channel Description This command configures 2.4 GHz radio channels for a specific W-IAP. Syntax Parameter Description Range Configures the specified 2.4 GHz channel. The valid channels for a band are determined by the AP regulatory domain. Configures the specified transmission power values. 0-127 dBm Usage Guidelines Use this command to configure radio channels for the 2.4 GHz band for a specific W-IAP.
g-external-antenna g-external-antenna Description This command configures external antenna connectors for a W-IAP. Syntax Parameter Description Range Default Configures the antenna gain. You can configure gain value in dBi for the following types of antenna: Diploe/Omni - 6 — l Dipole/Omni l Panel l Sector Panel -12 Sector - 12 Usage Guidelines If your W-IAP has external antenna connectors, you need to configure the transmit power of the system.
(Instant AP)# g-external-antenna 12 Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
gre per-ap-tunnel gre per-ap-tunnel no… Description This command configures a generic routing encapsulation (GRE) tunnel from each W-IAP to the VPN/GRE Endpoint rather than the tunnels created just from the Virtual Controller. Syntax Parameter Description gre per-ap-tunnel Creates a GRE tunnel from the W-IAP to the VPN/GRE endpoint. no… Removes the configuration.
gre primary gre primary no… Description This command configures a host for the primary VPN/GRE endpoint. Syntax Parameter Description gre primary Specifies the fully qualified domain name (FQDN) of the primary host. no… Removes the configuration. Usage Guidelines Use this command to configure the primary VPN/GRE host.
gre type gre type Description This command configures a GRE protocol number as GRE type. Syntax Parameter Description Range Default gre type Configures the protocol number or IP address for GRE type 16-bit protocol number 0 Usage Guidelines Use this command to specify GRE type. The 16-bit protocol number uniquely identifies a Layer-2 tunnel. The W-IAPs or controllers at both endpoints of the tunnel must be configured with the same protocol number.
help help Description This command displays help for the CLI. Usage Guidelines This command displays keyboard editing commands that allow you to make corrections or changes to the command without retyping. You can also enter the question mark (?) to get various types of command help: l When typed at the beginning of a line, the question mark lists all commands available in the current mode. l When typed at the end of a command or abbreviation, the question mark lists possible commands that match.
Command History Version Description Dell Networking WSeries Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
hostname hostname Description This command changes the hostname of the Virtual Controller. Syntax Parameter Description Configures a hostname for the Virtual Controller. Usage Guidelines The hostname is used as the default prompt. You can use any alphanumeric character, punctuation, or symbol characters. When spaces, plus symbols (+), question marks (?), or asterisks (*) are used, enclose the text in quotes. Example The following example configures host name for a W-IAP.
hotspot anqp-3gpp-profile hotspot anqp-3gpp-profile 3gpp-plmn1…3gpp-plmn6 enable no… Description This command configures a 3rd Generation Partnership Project (3GPP) Cellular Network for hotspots that have roaming relationships with cellular operators. Syntax Parameter Description hotspot anqp-3gpp-profile Creates a 3GPP profile. 3gpp-plmn1…3gpp-plmn6 Configures the Public Land Mobile Networks (PLMN) value of the network.
Command Information W-IAP Platform Command Mode All platforms Configuration mode and the 3GPP hotspot profile configuration sub-mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
hotspot anqp-domain-name-profile hotspot anqp-domain-name-profile domain-name enable no… Description This command defines the domain name to be sent in an Access Network Query Protocol (ANQP) information element in a Generic Advertisement Service (GAS) query response. Syntax Parameter Description hotspot anqp-domain-name-profile Creates a domain profile. domain-name Configures a domain name of the hotspot operator.
hotspot anqp-ip-addr-avail-profile hotspot anqp-ip-addr-avail-profile enable ipv4-addr-avail ipv6-addr-avail no… Description This command defines the available IP address types to be sent in an Access network Query Protocol (ANQP) information element in a Generic Advertisement Service (GAS) query response. Syntax Parameter Description hotspot anqp-ip-addr-avail-profile Creates an ANQP IP Address availability profile. enable Enables the IP address availability profile.
Command Information W-IAP Platform Command Mode All platforms Configuration mode and the ANQP IP address availability profile configuration sub-mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
hotspot anqp-nai-realm-profile hotspot anqp-nai-realm-profile enable nai-home-realm nai-realm-auth-id-1 nai-realm-auth-id-2 nai-realm-auth-value-1 nai-realm-auth-value-2 nai-realm-eap-method nai-realm-encoding nai-realm-name no… Description This command defines a Network Access Identifier (NAI) realm information that can be sent as an Access network Query Protocol (ANQP) information element in a Generic Advertisemen
Parameter Description Range nai-realm-auth-value1 nai-realm-auth-value2 Configures a value for NAI realm authentication. Use the nai-realm-auth-value-1 command to select an authentication value for the authentication method specified by nai-realm-auth-id-1. Use thenai-realm-auth-value-2 command to select the authentication value for the authentication method specified bynai-realm-auth-id-2.
Parameter Description Range Configures any of the following EAP methods: crypto-card, eap-aka, eapsim, eap-tls, eap-ttls, generic-tokencard, identity notification, one-timepassword, peap, peapmschapv2 l crypto-card— Crypto card authentication l eap-aka—EAP for UMTS Authentication and Key Agreement l eap-sim—EAP for GSM Subscriber Identity Modules l eap-tls—EAP-Transport Layer Security l eap-ttls—EAP-Tunneled Transport Layer Security l generic-token-card—EAP Generic Token Card (
Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Configuration mode and the NAI realm profile configuration sub-mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
hotspot anqp-nwk-auth-profile hotspot anqp-nwk-auth-profile enable nwk-auth-type url no… Description This command configures an ANQP network authentication profile to define authentication type being used by the hotspot network. Syntax Parameter Description Range hotspot anqp-nwk-auth-profile Configures an ANQP network authentication profile. — enable Enables the network authentication profile.
Usage Guidelines When the asra option is enabled in the hotspot profile associated with a WLAN SSID, the settings configured for the network authentication profile are sent in the GAS response to the client. Example The following command configures a network authentication profile for DNS redirection.
hotspot anqp-roam-cons-profile hotspot anqp-roam-cons-profile enable roam-cons-oi roam-cons-oi-len no… Description This command configures the Roaming Consortium Organization Identifier (OI) information to be sent in an Access network Query Protocol (ANQP) information element in a Generic Advertisement Service (GAS) query response. Syntax Parameter Description Range hotspot anqp-roam-cons-profile Creates roaming consortium profile.
Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Configuration mode and the ANQP roaming consortium profile configuration sub-mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
hotspot anqp-venue-name-profile hotspot anqp-venue-name-profile enable venue-group venue-lang-code venue-name venue-type no… Description This command defines venue information be sent in an Access network Query Protocol (ANQP) information element in a Generic Advertisement Service (GAS) query response. Syntax Parameter Description Range Default hotspot anqpvenue-nameprofile Creates a ANQP venue name profile.
Parameter Description Range Default command. venue-lang-code Configures an ISO 639 language code that identifies the language used in the Venue Name field. — — venue-name Configures the venue name to be advertised in the ANQP IEs. If the venue name includes spaces, the name must be enclosed in quotation marks, e.g. “Midtown Shopping Center”. — — venue-type Specifies the venue type to be advertised in the IEs.
Venue Group business educational factory-and-industrial institutional mercantile outdoor 0511587-03 | September 2014 Associated Venue Type Value l restaurant l theater l bar l coffee-shop l zoo-or-aquarium l emergency-cord-center l unspecified l doctor l bank l fire-station l police-station l post-office l professional-office l research-and-dev-facility l attorney-office l unspecified l school-primary l school-secondary l univ-or-college l unspecified l facto
Venue Group residential Associated Venue Type Value l rest-area l traffic-control l bus-stop l kisok l unspecified l private-residence l hotel l dormitory l boarding-house l unspecified storage unspecified utility-and-misc unspecified vehicular l unspecified l automobile-or-truck l airplane l bus l ferry l ship l train l motor-bike Example The following command defines an ANQP Venue Name profile for a shopping mall: (Instant (Instant (Instant (Instant (Instant (Ins
Command Information W-IAP Platform Command Mode All platforms Configuration mode and the ANQP venue name profile configuration sub-mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
hotspot h2qp-conn-cap-profile hotspot h2qp-conn-cap-profile enable esp-port icmp tcp-ftp tcp-http tcp-pptp-vpn tcp-ssh tcp-tls-vpn tcp-voip udp-ike2 udp-ipsec-vpn udp-voip no… Description This command configures a Hotspot 2.0 Query Protocol (H2QP) profile that advertises hotspot protocol and port capabilities. Syntax Parameter Description hotspot h2qp-conn-capprofile Creates a connection capability profile. enable Enables the connection capability H2QP profile.
Usage Guidelines Use this command to configure the values to be sent in an ANQP IE to provide information about the IP protocols and associated port numbers that are available and open for communication. Example The following example allows the H2QP connection capability profile to advertise the availability of ICMP and HTTP ports.
hotspot h2qp-oper-name-profile hotspot h2qp-oper-name-profile enable op-fr-name op-lang-code no… Description This command configures a Hotspot 2.0 Query Protocol (H2QP) operator-friendly name profile. Syntax Parameter Description Range Default hotspot h2qp-oper-nameprofile Creates an operator-friendly name profile. — — enable Enables the operator-friendly name profile.
Command Information W-IAP Platform Command Mode All platforms Configuration mode and the H2QP operator friendly name profile configuration sub-mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
hotspot h2qp-oper-class-profile hotspot h2qp-oper-class-profile enable op-class no… Description This command configures a Hotspot 2.0 Query Protocol (H2QP) profile that defines the Operating Class to be sent in the H2QP IE. Syntax Parameter Description Range Default hotspot h2qp-operclass-profile Creates operating class profile. — — enable Enables the operating class profile. — — op-class Configures the operating class for the devices’ BSS.
hotspot h2qp-wan-metrics-profile hotspot h2qp-wan-metrics-profile at-capacity downlink-load downlink-speed enable load-duration symm-link uplink-load uplink-speed wan-metrics-link-status no… Description This command configures a Hotspot 2.0 Query Protocol (H2QP) profile that specifies the hotspot WAN status and link metrics.
Parameter Description Range Default uplink-load The percentage of the WAN uplink that is currently utilized. If no value is set, this parameter will show a default value of 0 to indicate that the downlink speed is unknown or unspecified. 1-100 0 (unspecified) uplink-speed Use the uplink parameter to indicate the current WAN backhaul uplink speed in Kbps.
Command Information W-IAP Platform Command Mode All platforms Configuration mode and the H2QP WAN metrics profile configuration sub-mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
hotspot hs-profile hotspot hs-profile access-network-type addtl-roam-cons-ois advertisement-profile {anqp-3gpp|anqp-domain-name|anqp-ip-addr-avail|anqp-nai-realm| anqpnwk-auth|anqp-roam-cons|anqp-venue-name|h2qp-conn-cap|h2qp-oper-class|h2qp-oper-name|h2qpwan-metrics} advertisement-protocol asra comeback-mode enable gas-comeback-delay group-frame-block hessid internet no p2p-cross-connect p2p-dev-mgmt pame-bi query-response-l
Parameter Description Range Default The corresponding integer value for this network type is 1. 0511587-03 | September 2014 l chargeable-public— This network provides access to the Internet based on payment. For example, a subscription-based Internet access in a coffee shop or a hotel offering chargeable inroom Internet access service. The corresponding integer value for this network type is 2. l free-public—This network is accessible to all without any charges applied.
Parameter Description Range Default addtl-roam-cons-ois Configures the number of additional roaming consortium Organization Identifiers (OIs) advertised by the AP. This feature supports up to three additional OIs, which are defined using the roam-cons-oi-1, roamcons-oi-2 and roam-cons-oi-3 parameters.
Parameter Description Range Default comeback-mode By default, ANQP information is obtained from a GAS Request and Response. If you enable the comeback-mode option, advertisement information is obtained using a GAS Request and Response. as well as a Comeback-Request and Comeback-Response. This option is disabled by default. — — enable Enables the hotspot profile.
Parameter Description Range Default pame-bi Enables the Pre-Association Message Exchange BSSID Independent (PAME-BI) bit, which is used by an AP to indicate whether the AP indicates that the Advertisement Server can return a query response that is independent of the BSSID used for the GAS Frame exchange. — — query-response-lengthlimit Configures the maximum length of the Generic Advertisement Service (GAS query response.
Parameter Description Range Default roam-cons-oi-1 roam-cons-oi-2 roam-cons-oi-3 Configures the roaming consortium OI to assign to one of the service provider’s top three roaming partners. This additional OI will only be sent to a client if the addtl-roam-cons- parameter is set to 1 or higher. — — assembly, business, business NOTE: The service provider’s own roaming consortium OI is configured using the hotspot anqp-roam-cons-profile command.
Parameter Description Range Default NOTE: This parameter only defines the venue type advertised in the IEs from hotspot APs. To define the venue type to be included in ANQP responses, use the hotspot anqp-venue-name-profile command. Usage Guidelines Use this command to configure a hotspot profile. Hotspot 2.0 is a Wi-Fi Alliance specification based on the 802.
l Roaming Consortium List: Defined using the hotspot anqp-roam-cons-profile command. l NAI Realm: Defined using the hotspot anqp-nai-realm-profile command. l Cellular Network Data: Defined using the hotspot anqp-3gpp-nwk-profile command. l Connection Capability: Defined using the hotspot h2qp-conn-capability-profile command. l Operator Class: Defined using the hotspot h2qp-op-cl-profile command. l Operator Friendly Name: Defined using the hotspot h2qp-operator-friendly-name-profile command.
Table 9: Venue Types Venue Group Associated Venue Type Value unspecified — The associated numeric value is 0. assembly l unspecified—The associated numeric value is 0. The associated numeric value is 1. l arena—The associated numeric value is 1. l stadium—The associated numeric value is 2. l passenger-terminal—The associated numeric value is 3. l amphitheater—The associated numeric value is 4. l amusement-park—The associated numeric value is 5.
Venue Group Associated Venue Type Value l long-term-care—The associated numeric value is 2. l alc-drug-rehab—The associated numeric value is 3. l group-home—The associated numeric value is 4. l prison-or-jail—The associated numeric value is 5. mercantile l unspecified—The associated numeric value is 0. The associated numeric value is 6. l retail-store—The associated numeric value is 1. l grocery-market—The associated numeric value is 2.
(Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant AP)(config)# hotspot hs-profile hs1 AP)(Hotspot2.0 "hs1")# enable AP)(Hotspot2.0 "hs1")# comeback-mode AP)(Hotspot2.0 "hs1")# gas-comeback-delay 10 AP)(Hotspot2.0 "hs1")# no asra AP)(Hotspot2.0 "hs1")# no internet AP)(Hotspot2.0 "hs1")# query-response-length-limit 127 AP)(Hotspot2.
iap-master iap-master no… Description This command provisions a W-IAP as a master W-IAP. Syntax Command/Parameter Description iap-master Provisions the W-IAP as a master W-IAP. no… Removes the configuration. Usage Guidelines Use this command to manually provision a W-IAP as a master W-IAP. Example The following example provisions a master IAP: (Instant AP)# iap-master Command History Version Description Dell Networking W-Series Instant 6.3.1.14.0 This command is introduced.
ids ids client-detection-level client-protection-level detect-adhoc-network detect-ap-flood detect-ap-impersonation detect-ap-spoofing detect-bad-wep detect-beacon-wrong-channel detect-block-ack-attack detect-chopchop-attack detect-client-flood detect-cts-rate-anomaly detect-disconnect-sta detect-eap-rate-anomaly detect-fatajack detect-hotspotter-attack detect-ht-40mhz-intolerance detect-ht-greenfield detect-invalid-addresscombination detect-invalid-mac-oui detect-malformed-assoc-req detect-ma
Syntax Parameter Description Range Default ids Creates an IDS policy — — client-detection-level Sets the client detection level. off, low, medium, high off client-protection-level Sets the client protection level. off, low, medium, high off detect-adhoc-network Enables detection of adhoc networks.
Parameter Description Range Default detect-eap-rate-anomaly Enables Extensible Authentication Protocol (EAP) handshake analysis to detect an abnormal number of authentication procedures on a channel and generate an alarm when this condition is detected. — — detect-fatajack Enables detection of fatjack attacks. — — detect-hotspotter-attack Enables detection of hotspot attacks. — — detect-ht-40mhzintolerance Enables detection of 802.
Parameter Description Range Default detect-power-save-dosattack Enables detection of Power Save DoS attack. — — detect-rate-anomalies Enables detection of rate anomalies. — — detect-rts-rate-anomaly Enables detection of RTS rate anomaly. — — detect-tkip-replay-attack Enables detection of TKIP replay attack. — — detect-unencrypted-valid Enables detection of unencrypted valid clients.
Parameter Description Range Default allowed to connect to an invalid AP. protect-windows-bridge Enables protection of a windows station bridging — — rogue-containment Controls Rogue APs. When rogue APs are detected, they are not automatically disabled. — — This option automatically shuts down rogue APs. When this option is enabled, clients attempting to associate to an AP classified as a rogue are disconnected through a denial of service attack.
Usage Guidelines Use this command to configure Intrusion Detection System (IDS) detection and protection policies. The IDS feature monitors the network for the presence of unauthorized W-IAPs and clients and enables you to detect rogue APs, interfering APs, and other devices that can potentially disrupt network operations. It also logs information about the unauthorized W-IAPs and clients, and generates reports based on the logged information.
(Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant AP)(IDS)# detect-overflow-ie AP)(IDS)# detect-overflow-eapol-key AP)(IDS)# detect-beacon-wrong-channel AP)(IDS)# detect-invalid-mac-oui AP)(IDS)# detect-valid-clientmisassociation AP)(IDS)# detect-disconnect-sta AP)(IDS)# detect-omerta-attack AP)(IDS)# detect-fatajack AP)(IDS)
ignore-image-check ignore-image-check Description This command ignores the automatic image check feature. The automatic image check feature automatically checks for a new version of Instant on the image server, once after the AP boots up and every week thereafter.
inactivity-ap-timeout inactivity-ap-timeout no… Description This command configures the timeout interval for inactive user sessions. Syntax Parameter Description Range Default inactivity-aptimeout Configures the inactivity timeout interval in seconds. 1-1000 1000 no… Removes any existing configuration. — — Usage Guidelines Use this command to configure an inactivity timeout interval for a W-IAP.
inbound-firewall inbound-firewall rule {permit|deny|src-nat|dst-nat ip }[] no… Description This command configures inbound firewall rules based on the source subnet. Syntax Command/Parameter Description Range Default inbound-firewall Opens the inbound firewall configuration mode. — — rule Creates an access rule. — — You can create up to 128 access rules.
Command/Parameter Description Range Default Specifies the ending port number until which the rule applies 1-65534 — dst-nat Allows the W-IAP to perform destination NAT on packets. — — src-nat Allows the W-IAP to perform source NAT on packets. When configured, the source IP changes to the outgoing interface IP address (implied NAT pool) or from the pool configured (manual NAT pool).
For all subnets, a deny rule is created by default as the last rule. If at least one rule is configured, the deny all rule is applied to the upstream traffic by default. Management access to the AP is allowed irrespective of the inbound firewall rule. For more information on configuring restricted management access, see restricted-mgmt-access. The inbound firewall is not applied to traffic coming through GRE tunnel.
internal-domains internal-domains domain-name no... Description This command configures valid domain names for the enterprise network. Syntax Parameter Description Range Default internal-domains Enables the internal-domain configuration submode — — domain-name Defines the valid domain names — — no… Removes any existing configuration — — Usage Guidelines Use this command to configure the DNS domain names that are valid on the enterprise network.
ip-address ip-address Description This command configures an IP address for the W-IAP. Syntax. Parameter Description Assigns an IP address to the W-IAP. Specifies the subnet mask. Specifies the gateway IP address. Specifies the DNS server IP address. Specifies the domain name.
ip dhcp ip dhcp bid client-count default-router dhcp-relay dhcp-server disable-split-tunnel dns-server domain-name exclude-address host ip-range lease-time option option82 alu reserve {first | last } server-type server-vlan subnet subnet-mask vlan-ip mask no… D
Parameter Description Range Default available in an IP address range configured for a DHCP scope and a client count of 9 is configured, only a few IP addresses (in this example, 9) from this range will be used and allocated to a branch. The W-IAP does not allow the administrators to assign the remaining IP addresses to another branch, although a lower value is configured for the client count.
Parameter Description Range Default When split-tunnel is disabled, all the traffic including the corporate and Internet traffic is tunneled irrespective of the routing profile specifications. If the GRE tunnel is down and when the corporate network is not reachable, the client traffic is dropped. dns-server Defines the DNS server IP address. — — domain-name Defines the domain name. — — host Allows you to specify the host MAC address.
Parameter Description Range Default configured client count. l For Distributed, L3 mode, you can configure any discontiguous IP ranges. The configured IP range is divided into multiple IP subnets that are sufficient to accommodate the configured client count. lease-time Defines a lease time for the client in minutes. — 720 option Defines the type and a value for the DHCP option to use.
Parameter Description Range Default vlan-id mask Defines the IP address and subnet mask for vlan of the DHCP server. — — no… Removes any existing configuration. — — Usage Guidelines Use this command to configure the DHCP address assignment for the branches connected to the corporate network through VPN. You can configure the following types of DHCP profiles.
(Instant AP)(DHCP Profile"corpNetwork1")# domain-name www.example.com (Instant AP)(DHCP Profile"corpNetwork1")# lease-time 1200 (Instant AP)(DHCP Profile"corpNetwork1")# ip-range 192.0.1.0 192.0.1.17 (Instant AP)(DHCP Profile"corpNetwork1")# reserve first 2 (Instant AP)(DHCP Profile"corpNetwork1")# option 176 "MCIPADD=10.72.80.34,MCPORT=1719,TFTPSRVR=10.80.0.
ip dhcp pool ip dhcp pool dns-server domain-name lease-time subnet subnet-mask no… Description This command configures a DHCP pool on the Virtual Controller. Syntax Parameter Description Range Default dns-server Defines the IP address of the DNS server. You can specify up to eight IP addresses as a comma separated list. — — domain-name Defines the name of domain to which the client belongs.
Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Configuration mode and IP DHCP configuration sub-mode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
l2tpv3 session l2tpv3 session cookie len value default-l2-specific-sublayer l2tpv3 tunnel tunnel-ip mask vlan no… Description This command configures an Layer-2 Tunnel Protocol (L2TP) session profile. Syntax Parameter Description Range Default l2tpv3 session Configures the session profile name.
(Instant AP)(L2TPv3 Session Profile "test_session")# tunnel-ip 1.1.1.1 mask 255.255.255.0 vlan 2 (Instant AP)(L2TPv3 Session Profile "test_session")# end (Instant AP)# commit apply Command History Version Description Dell Networking W-Series Instant 6.4.0.24.1 This command was modified. Dell Networking W-Series Instant 6.2.1.03.4 This command is introduced. Command Information W-IAP Platform Command Mode W-IAP108 Configuration mode and L2TPV3 session profile configuration sub-mode.
l2tpv3 tunnel l2tpv3 tunnel backup peer-address checksum failover-mode failover-retry-count failover-retry-interval hello-timeout local-port message-digest-type mtu peer-port primary peer-address secret-key no... Description This command configures an L2TP tunnel profile.
Parameter Description Range Default the MD AVP. mtu Configures a Maximum Transmission Unit (MTU) value for the tunnel. 1—65535 1460 peer-port Assigns a UDP server port to the remote end. 1—65535 1701 primary peer-address Assigns IP address of the remote end tunnel. — — secret-key Configures a shared key to use for message digest. — — Usage Guidelines Use this command tunnel data or traffic to L2TP Network Server (LNS).
l3-mobility l3-mobility home-agent-load-balancing virtual-controller subnet no... Description This command configures Layer-3 mobility on a W-IAP. Syntax Parameter Description Range Default l3-mobility Enables Layer-3 mobility configuration submode. — — home-agent-loadbalancing Enables home agent load balancing.
Usage Guidelines Use this command to configure layer-3 mobility domains on a W-IAP. Example The following example configures L3-mobility: (Instant (Instant (Instant (Instant (Instant (Instant AP)(config)# l3-mobility AP)(L3-mobility)# home-agent-load-balancing AP)(L3-mobility)# virtual-controller 192.0.2.1 AP)(L3-mobility)# subnet 192.0.2.2 255.255.255.0 1 192.0.2.1 AP)(L3-mobility)# end AP)# commit apply Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.
led-off led-off no… Description This command disables LED display on a W-IAP. Syntax Command/Parameter Description led-off Disables LED display. no… Re-enables LED display. Usage Guidelines Use this command to disable the LED display. Example The following example disables LED display on a W-IAP: (Instant AP)(config)# led-off Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced.
logout logout Description This command logs you out of the current CLI session. Usage Guidelines Use this command to log out of the current CLI session and return to the user login prompt. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
mesh mesh no… Description This command sets up mesh network on a W-IAP. Syntax Parameter Description mesh Enables mesh network on the W-IAP. no… Removes the configuration. Usage Guidelines Use this command to set up mesh network on a W-IAP. Mesh network requires at least one valid uplink (wired or 3G) connection. Any provisioned W-IAP that has a valid uplink (wired or 3G) functions as a mesh portal, and the W-IAP without an Ethernet link functions as a mesh point.
Command Information W-IAP Platform Command Mode All platforms Configuration mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
mgmt-accounting mgmt-accounting command all no… Description This command is used to enable accounting privileges on TACACS+ servers for management users. Syntax Parameter Description mgmt-accounting command all Configures TACACS+ servers to enable accounting for management users. no… Removes the configuration. Usage Guidelines Use this command to record the user name of the management users and the respective IP address sending the request to account for the usage of the authorized network services.
mgmt-auth-server mgmt-auth-server no… Description This command configures authentication servers for management user interface of the Virtual Controller. Syntax Parameter Description mgmt-auth-server Configures a server for management user authentication. no… Removes the configuration. Usage Guidelines Use this command to configure a management authentication server for administrator users of a Virtual Controller.
mgmt-auth-server-load-balancing mgmt-auth-server-load-balancing no… Description This command enables load balancing when two authentication servers are configured for management user authentication. Syntax Parameter Description mgmt-auth-server-load-balancing Enables load balancing between the primary and the backup authentication servers no… Removes the configuration. Usage Guidelines Use this command to enable load-balancing when two servers are configured.
mgmt-auth-server-local-backup mgmt-auth-server-local-backup no… Description Configures a secondary internal authentication server that will validate the management interface user credentials at runtime. Syntax Parameter Description mgmt-auth-server-local-backup Configures a backup internal server for management user authentication. When enabled, the authentication switches to Internal if there is no response from the RADIUS server (RADIUS server timeout). no… Removes the configuration.
mgmt-user mgmt-user [][] Description This command configures user credentials for access to the Virtual Controller Management User Interface. Syntax Parameter Description mgmt-user Configures administrator credentials. Creates a User name for the administrator user. Creates a password for the administrator user. Indicates the type of the user. For example, users with read-only privilege or the guest management user.
name name Description This command configures a unique name for the W-IAP. Syntax Parameter Description name Configures a name for the W-IAP or the Virtual Controller. Usage Guidelines Use this command to configure a name for the W-IAP: Example The following example configures a name for the W-IAP: (Instant AP)# hostname Command History Version Description Dell Networking W-Series Instant 6.2.1.0- This command is introduced. 3.
ntp-server ntp-server no… Description This command configures NTP server for a W-IAP. Syntax Parameter Description Default ntp-server Configures the IP address or the URL (domain name) of the NTP server. pool.ntp.org no Removes the configuration — Usage Guidelines The Network Time Protocol (NTP) helps obtain the precise time from a server and regulate the local time in each network element.
opendns opendns no... Description This command configures OpenDNS credentials for filtering content and to create Internet access policies that allow or deny user access to websites based on website categories and security ratings. Syntax Parameter Description opendns Configures user credentials to enable access to OpenDNS to provide enterprise-level content filtering. Configures user name to access OpenDNS. Configures password to access OpenDNS.
organization organization no… Description This command configures an organization string for W-IAPs managed or monitored by the W-AirWave Management console. Syntax Parameter Description Range organization Specifies the name of your organization.
Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Configuration mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
ping ping Description This command sends ICMP echo packets to the specified IP address. Syntax Parameter Description Displays the IP address of the host. Usage Guidelines You can send up to five ICMP echo packets to a specified IP address. The W-IAP times out after two seconds. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced.
pppoe-uplink-profile pppoe-uplink-profile pppoe-username pppoe-passwd pppoe-svcname pppoe-chapsecret pppoe-unnumbered-local-l3-dhcp-profile no… Description Use this command to configure PPPoE uplink profile. Syntax Parameter Description pppoe-uplink-profile Creates an uplink profile and enables the PPPoE uplink profile configuration mode.
Command History Version Description Dell Networking W-Series Instant 6.4.2.0-4.1.1 This command is modified. Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Configuration mode and PPPoE uplink profile configuration submode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
proxy proxy {exception | server } Description This command configures HTTP proxy settings. Syntax Parameter Description exception Sets the IP address or the domain name of the host to be added under the exception list. server Sets the HTTP proxy server's IP address or domain name and the port number. Usage Guidelines This command configures the HTTP proxy settings in a W-IAP to download the image from the cloud server.
reload reload Description This command performs a reboot of the Virtual Controller. Syntax Parameter Description Reloads all W-IAPs in a cluster. Usage Guidelines Use this command to reboot a W-IAP after making configuration changes or under the guidance of Dell Networks customer support. The reload command powers down the W-IAP, making it unavailable for configuration.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
remove-blacklist-client remove-blacklist-client Description This command allows you to delete the clients that are blacklisted. Syntax Parameter Description MAC-address Adds the MAC address of the blacklisted client. AP_name Adds the access point name to which the client is connected to. no… Removes the specified configuration parameter. Usage Guidelines Use this command to remove the entries for the clients that are dynamically blacklisted.
restrict-corp-access restrict-corp-access no… Description This command configures restricted access to the corporate network. Syntax Parameter Description no… Removes the configuration. Usage Guidelines Use this command to configure restricted corporate to block unauthorized users from accessing the corporate network. When restricted corporate access is enabled, corporate access is blocked from the uplink port of master W-IAP, including clients connected to a slave W-IAP.
restricted-mgmt-access restricted-mgmt-access no… Description This command configures management subnet on a W-IAP. Syntax Parameter Description subnet Configures a management subnet address. mask Configures the subnet mask for the management subnet address. no… Removes the configuration. Usage Guidelines Use this command to configure management subnets. This ensures that the W-IAP management is carried out only from these subnets.
rf dot11a-radio-profile rf dot11a-radio-profile beacon-interval csa-count dot11h interference-immunity legacy-mode max-distance spectrum-band spectrum-monitor no… Description This command configures a 5.GHz or 802.11a radio profile for a W-IAP. Syntax Parameter Description Range Default rf dot11a-radioprofile Enables the 5.0 GHz RF configuration submode — — beacon-interval Enter the Beacon period for the W-IAP in milliseconds.
Parameter Description Range Default Noise Immunity feature. l Level 3— Level 2 settings and weak OFDM immunity. This level minimizes false detects on the radio due to interference, but may also reduce radio sensitivity. This level is recommended for environments with a high-level of interference related to 2.4 GHz appliances such as cordless phones. l Level 4— Level 3 settings, and FIR immunity.
Example The following example configures the 5 GHz radio profile: (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant AP)(config)# rf dot11a-radio-profile AP)(RF dot11a Radio Profile)# beacon-interval 100 AP)(RF dot11a Radio Profile)# legacy-mode AP)(RF dot11a Radio Profile)# dot11h AP)(RF dot11a Radio Profile)# interference-immunity 3 AP)(RF dot11a Radio Profile)# max-distance 600 AP)(RF dot11a Radio Profile)# csa-count 2 AP)(RF dot11a Radio Profile)# spectrum-monitor AP)(RF d
rf dot11g-radio-profile rf dot11g-radio-profile beacon-interval csa-count dot11h interference-immunity legacy-mode max-distance spectrum-monitor no… Description This command configures a 2.4.GHz or 802.11g radio profile for a W-IAP. Syntax Parameter Description Range Default rf dot11g-radioprofile Enables the 2.4 GHz RF configuration submode — — beacon-interval Enter the Beacon period for the W-IAP in milliseconds.
Parameter Description Range Default Noise Immunity feature. l Level 3— Level 2 settings and weak OFDM immunity. This level minimizes false detects on the radio due to interference, but may also reduce radio sensitivity. This level is recommended for environments with a high-level of interference related to 2.4 GHz appliances such as cordless phones. l Level 4— Level 3 settings, and FIR immunity.
(Instant (Instant (Instant (Instant (Instant (Instant (Instant AP)(RF AP)(RF AP)(RF AP)(RF AP)(RF AP)(RF AP)(RF dot11g dot11g dot11g dot11g dot11g dot11g dot11g Radio Radio Radio Radio Radio Radio Radio Profile)# Profile)# Profile)# Profile)# Profile)# Profile)# Profile)# no legacy-mode dot11h interference-immunity 3 max-distance 600 csa-count 2 spectrum-monitor end Command History Version Description Dell Networking W-Series Instant 6.3.1.1-4.0 This command is modified.
rf-band rf-band {2.4| 5.0| all} Description This command configures the radio frequency band for a W-IAP. Syntax Parameter Description Range Default rf-band {2.4| 5.0| all} Configures a radio frequency band for a W-IAP. You can configure any of the following options: 2.4, 5.0, all all l 2.4—For 2.4 GHz band or 802.11g configuration l 5—For 5 GHz and 802.11a configuration l all - For a mixed configuration of 2.4.GHz and 5 GHz. If you do not specify any value, by default both 5 GHz and 2.
rft rft test profile antenna-connectivity ip-addr dest-mac phy {a|g} ht-link-quality ip-addr dest-mac phy {a|g} mcs link-quality ip-addr dest-mac phy {a|g} raw ip-addr dest-mac phy {a|g} Description This command is used for RF troubleshooting.
Command Information W-IAP Platform Command Mode All platforms except W-IAP224/225, and W-IAP274/275 Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
routing-profile routing-profile route no... Description This command configures a routing profile to define the corporate subnets, which must to be tunneled through IPSec. Syntax Parameter Description routing-profile Creates a routing profile for routing traffic into the VPN tunnel. route Configures route parameters. Configures the destination network that is reachable through the VPN tunnel.
show 1xcert show 1xcert Description This command displays the details about the external server certificate, which is used by the W-IAP for client authentication. Usage Guidelines Use this command to view information about the server certificates uploaded to a W-IAP. Example The following example shows the output of show 1xcert command: Default Server Certificate: Version :3 Serial Number :01:DA:52 Issuer :C=US, O=GeoTrust Inc.
show about show about Description This command displays information about Instant. Usage Guidelines Use this command to view information such as Instant version, build time and W-IAP model. Example The show about command displays the Build Time, W-IAP model number, the Instant version, website address of organization, and Copyright information. The following example shows the show about command output: Name :Aruba Operating System Software Type :W-AP105 Build Time :2013-04-19 08:30:19 PDT Version :6.2.1.
show access-rule show access-rule Description This command displays the details of access rules configured for the wired or wireless clients associated with a W-IAP. Syntax Parameter Description Displays the access rule configuration details based the name specified for this parameter. Usage Guidelines Use this command to view information an access rule configured for a network profile.
any any match app baidu-higames any deny any deny any deny any deny any deny any deny any match app bluejayfilms any match appcategory gaming any match webcategory shopping any match webcategory abused-drugs any match webcategory dead-sites any match high-risk-sites Blacklist App Throttle (Up:Down) Mirror ---- ---------------------- --- ------- ------------Vlan Id :0 ACL Captive Portal:disable ACL ECP Profile :default CALEA :disable Bandwidth Limit :upstream disable DisScan webreput
show access-rule-all show access-rule-all Description This command displays the details of the access rules configured for all wired and wireless profiles on the WIAP. Usage Guidelines Use this command to view information access rules configured for all wired and wireless profiles on the W-IAP.
Parameter Description Access Rule Name Displays the name of the access rule. In use Indicates if the access rules are in use. Access Rules Displays the access rules parameter for each rule configured for the SSID or Wired profile users. VLAN Id Indicates the VLAN ID associated with the SSID or wired profile access rules ACL Captive Portal Indicates if the ACL rules are applicable to the captive portal users. Command History Version Description Dell Networking W-Series Instant 6.2.1.03.
show acl show acl {domains} Description This command displays the Access Control List (ACL) configuration details. Syntax Parameter Description domains Displays the domains configured with an access control list. Usage Guidelines Use this command to view the ACL configuration details.
show airgroup show airgroup {blocked-queries [dlna| mdns]| blocked-service-id [dlna| mdns]| cache { | entries [dlna| mdns]} | cppm {auth server [coa-capable | non-coa-only] | entries | query-interval | server}| cppm-entry | debug statistics| internal-state statistics | servers [dlna| mdns| verbose]| status | swarm-info| users [dlna| mdns| verbose]} Description This command displays the AirGroup configuration details for a W-IAP client.
show airgroup blocked-queries The show airgroup blocked-queries command output displays the blocked queries if any: AirGroup dropped Query IDs -------------------------Service ID #query-hits ---------- ----------Num dropped Query IDs:0 show airgroup blocked-service-id The show airgroup blocked-service-id command output displays the blocked AirGroup service IDs if any: AirGroup Blocked Service IDs ---------------------------Origin Service ID #response-hits ------ ---------- -------------Num Blocked Service-
Column Description Expiry Indicates the expiration details. Last Update Indicates when the entries were last updated. show airgroup cppm auth server non-coa-only The following output is displayed for the show airgroup cppm auth server non-coa-only command: All Airgroup Non-CoA-only Servers known to MDNS ----------------------------------------------Server IP-Address Port timeout rfc3576 rfc3576-only rfc3576-port ------ ---------- ---- ------- ------- ------------ -----------test 192.0.2.
swarm id = fc6520ad018ee6eb13bdc6b985e0fe6361bd37f7d25212a77e -------------------------------------------------------------------ap id = d8:c7:c8:c4:42:98 ap ip = 192.0.2.
Peer VC address :192.168.20.2 Peer VC address :192.168.30.2 Peer VC address :192.168.40.2 Peer VC address :0.0.0.0 Peer VC address :0.0.0.0 Peer VC address :0.0.0.0 Peer VC address :0.0.0.
CPPM Device-Entry Deleted N/A N/A 0 Internal MDNS Statistics -----------------------Functionality Hit Count Since Last Read Hit Count Total microsec (since last read) Average Time in microsec (alltime) ------------------------------------- ---------------------------------------- ---------------------------------Response - Cache Update 0 0 0 Response 0 0 0 Query - prepare records + Policy 0 0 0 Query - Policy 0 0 0 Query - resp pkt gen & send 0 0 0 Query - Response packet send 0 0 0 Query 0 0 0 Internal DLN
Column Description Type Indicates the type of server. Hostname Indicates the hostname of the AirGroup servers. Service Indicates if AirGroup services such as AirPlay or AirPrint are configured. VLAN Displays VLAN details of the AirGroup servers. Wired/Wireless Displays if the AirGroup server is connected to a wired or wireless interface. Role Displays the user role details. Group Displays the server group. Username Displays the username details. AP-name Displays the name of the AP.
---------------------------Service Status ------- -----airplay Disabled airprint Disabled itunes Disabled remotemgmt Disabled sharing Disabled chat Disabled Chromecast Disabled DLNA Media Disabled DLNA Print Disabled allowall Disabled The output of this command provides the following information: Column Description Airgroup feature status Indicates if the AirGroup feature such as DLNA or MDNS support is enabled. AirGroup Multi Swarm status Indicates if the inter cluster mobility is enabled.
MAC IP Host Name VLAN Wired/Wireless Role Username AP-Mac Query/Resp --- -- --------- ---- -------------- ---- -------- ------ ---------Num Users:0 The output of this command provides the following information: Column Description MAC Indicates the MAC address of the AirGroup clients. IP Indicates the IP address of the AirGroup clients. Host Name Indicates the hostname of the AirGroup clients. VLAN Displays VLAN details of the AirGroup clients.
show airgroupservice show airgroupservice [disallow {role| vlan}] Description This command displays the AirGroup service configuration details for a W-IAP. Syntax Parameter Description show airgroupservice Displays a summary of the configuration details for AirGroup services. disallow {role |vlan} Displays the user roles or VLANs that are restricted from accessing AirGroup services.
_rfb. _tcp _net- assistant._tcp AirGroupService Details ----------------------Service Description status Disallowed-Role Disallowed-VLAN ID ------- ----------- ------ --------------- --------------- -sharing Sharing Disabled _odi sk._tcp _afp overtcp._tcp _xgr id._tcp chat Chat Disabled _pre sence.
Command History Version Description Dell Networking W-Series Instant 6.4.0.2-4.1 This command is modified. Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show airgroupservice-ids show airgroupservice-ids Description This command displays the AirGroup service IDs configured on a W-IAP for its AirGroup clients. Syntax Parameter Description service Indicates the name of the service and displays the service ID details of specified AirGroup service. Usage Guidelines Use the show airgroupservice command to view the IDs of the AirGroup services configured on a W-IAP.
show ale show ale {config| status} Description This command displays the ALE configuration details. Syntax Parameter Description config Displays the ALE configuration details. status Displays the status of ALE server. Usage Guidelines Use this command to view the ALE configuration status.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show alert global show alert global [count] Description This command displays the list of client alerts for a W-IAP. Syntax Parameter Description Filters client alerts based on the specified number. Usage Guidelines Use this command to view the client alerts for a W-IAP. The client alerts occur when clients are connected to the Instant network. Alerts are generated when a client encounters problems while accessing or connecting to the W-IAP network.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show alg show alg Description This command displays the Application Layer Gateway (ALG) protocol information configured on a W-IAP. Usage Guidelines Use this command to view configuration details for the ALG protocols. An application-level gateway consists of a security component that augments a firewall or NAT used in a network.
show allowed-aps show allowed-aps Description This command displays the list of W-IAPs that are allowed to join the W-IAP cluster. Usage Guidelines Use this command to view the W-IAP whitelist.
show all monitor show all monitor active-laser-beams Description This command shows information for Dell Networking W-Series Instant Air Monitors. Usage Guidelines Use this command to view the information on Dell Networking W-Series Instant Air Monitors. Syntax Parameter Description active-laser-beams Show active laser beam generators. The output of this command shows a list of all W-IAPs that are actively performing policy enforcement containment such as rogue containment.
show amp-audit show amp-audit Description This command displays the set of configurations on the W-AirWave Management Platform. Usage Guidelines Use this command to view the AMP related configurations.
3gpp-plmn1 "40486" 3gpp-plmn2 "" 3gpp-plmn3 "" 3gpp-plmn4 "" 3gpp-plmn5 "" 3gpp-plmn6 "" hotspot anqp-ip-addr-avail-profile "ip1" enable ipv4-addr-avail no ipv6-addr-avail hotspot anqp-domain-name-profile "dn1" enable domain-name "DomainName" hotspot h2qp-oper-name-profile "on1" enable op-lang-code eng op-fr-name "FriendlyName" hotspot hs-profile "hs1" enable comeback-mode no asra no internet pame-bi group-frame-block p2p-dev-mgmt no p2p-cross-connect addtl-roam-cons-ois 0 gas-comeback-delay 10 query-respon
max-authentication-failures 0 vlan 200 rf-band all captive-portal disable mac-authentication l2-auth-failthrough dtim-period 1 inactivity-timeout 1000 broadcast-filter none radius-accounting blacklist dmo-channel-utilization-threshold 90 local-probe-req-thresh 0 max-clients-threshold 64 hotspot-profile "hs1" auth-survivability cache-time-out 24 wlan external-captive-portal server localhost port 80 url "/" auth-text "Authenticated" auto-whitelist-disable https blacklist-time 3600 auth-failure-blacklist-time
description AirPlay airgroupservice airprint disable description AirPrint per-ap-settings d8:c7:c8:c4:42:98 hostname d8:c7:c8:c4:42:98 ip-address 10.17.161.254 255.255.255.0 10.17.161.1 10.13.6.110 "" swarm-mode cluster wifi0-mode access wifi1-mode access g-channel 0 0 a-channel 0 0 uplink-vlan 0 g-external-antenna 0 a-external-antenna 0 The output of this command provides the following information: Command History Version Description Dell Networking WSeries Instant 6.4.0.2-4.
show ap-alert show ap-alert Description This command displays all the alerts received for the specified APs. Usage Guidelines Use this command to check all the alerts received for all the APs specified. Example The following example shows the output of show ap-alert command.
show ap-env show ap-env Description This command displays all provisioned AP parameters such as the type of antenna used by a. The output of this command also indicates if the W-IAP is provisioned as a master W-IAP. Usage Guidelines Use this command to view the antenna configuration details for a W-IAP.
show aps show aps [scanning][sync] Description This command displays all active W-IAPs, W-IAP scanning, and synchronization status. Syntax Parameter Description aps Displays the list of all active W-IAPs in the cluster. aps scanning Displays W-IAP scanning details. aps sync Displays W-IAP synchronization details. Usage Guidelines Use this command to view the list of active W-IAPs, W-IAP scanning and synchronization details.
Column Description Mesh Role Indicates if the W-IAP is functioning as Mesh Point or mesh Portal. 2.4 Channel Indicates the channels used by the W-IAP in the 2.4 GHz band. 2.4 Power(dB) Indicates the transmission power allocated for 2.4 Ghz band channels. 2.4 Utilization Indicates the percentage of utilization of 2.4 GHz channels. 2.4 Noise Floor Indicates the noise floor of the 2.4 GHz channels. 5.0 Channel Indicates the channels used by the W-IAP in the 5 GHz band. 5.
The following output is displayed for the show aps scanning command: AP Sync List -----------MAC IP Address Class Current Version --- ---------- ----- --------------- The output of this command includes the following parameters: Column Description MAC Indicates MAC address of the W-IAP with which the current W-IAP is synchronized. IP address Displays the IP address of the W-IAP. Class Indicates if the W-IAP is serving as master or slave.
show ap allowed-channels show ap allowed-channels Description This command displays a list of allowed channels for a W-IAP. Syntax Parameter Description Specify a country code to display allowed channels for that country. Usage Guidelines Specify the country code for your W-IAP during the initial setup. Changing the country code causes the valid channel lists to be reset to the defaults for that country.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ap allowed-max-EIRP show ap allowed-max-EIRP [] Description This command displays the maximum EIRP settings for the country in which the W-IAP is currently operational. You can also view the maximum EIRP settings for a specific country. Syntax Parameter Description [] Displays the EIRP settings allowed for a specific country. Usage Guidelines Use this command to view the maximum EIRP settings for a W-IAP.
show ap arm show ap arm {bandwidth-management | history | neighbors |rf-summary | scan-times} Description This command displays information about bandwidth management, historical statistics, W-IAP neighbors, RF summary, and scanning details for the W-IAP. Syntax Parameter Description bandwidth management Displays ARM bandwidth details for a W-IAP. history Displays detailed information about the ARM configuration changes over a period of time. neighbors Displays details about the ARM neighbors.
Column Description Client Displays the list of W-IAP clients connected through the Wi-Fi interface. Tx Pkt Displays the transmission packet details associated with the interface. Tx Byte Displays the number of bytes in the transmission packets associated with the interface. Tx Alloc (ms) Indicates the time allocated for transmission in milliseconds. Tx Time (ms) Indicates the transmission time in milliseconds. Rx Time (ms) Indicates the reception time in milliseconds.
2013-05-10 09:04:24 149+ 157+ 27 27 I 2013-05-10 06:08:59 157+ 149+ 27 27 I 2013-05-10 05:55:10 153- 157+ 27 27 I 2013-05-10 05:11:21 157+ 153- 27 27 I Interface :wifi1 ARM History ----------Time of Change Old Channel New Channel Old Power New Power Reason -------------- ----------- ----------- --------- --------- -----2013-05-11 04:16:28 6 1 24 24 I 2013-05-11 03:58:53 11 6 24 24 I 2013-05-11 03:13:44 1 11 24 24 I 2013-05-11 01:23:32 6 1 24 24 I 2013-05-11 01:04:29 11 6 24 24 I 2013-05-11 00:26:16 1 11 24
Column Description Reason Indicates the reason for changes in channels. For more information about the reason, see the description below the command output. show ap arm neighbors The show ap arm neighbors command displays the ARM settings on the W-IAP neighbors.
36 0 0 0 93 3/2/0/0/94 0/0(0) 97/40//0/0(137) 40 0 0 0 93 9/2/0/0/92 0/0(0) 120/82//0/0(202) 44 0 0 0 93 2/1/0/1/99 0/0(0) 161/88//0/0(249) 48 0 0 0 93 9/2/0/0/93 0/0(0) 157/59//0/0(216) 52 0 0 0 93 0/0/0/0/93 0/0(0) 15/52//0/0(67) 56 0 0 0 93 5/0/0/0/95 0/0(0) 0/18//0/0(18) 60 0 0 0 93 0/0/0/0/94 0/0(0) 29/14//0/0(43) 64 0 0 0 93 6/0/0/0/94 0/0(0) 43/10//0/0(53) 149 0 0 0 93 3/2/0/0/99 0/0(0) 113/41//0/0(154) 153 0 0 2 93 23/23/0/1/100 0/0(0) 124/68//0/0(192) 157 0 0 0 93 2/1/0/1/94 0/0(0) 97/79//0/0(176)
Column Description cov-idx(Total) Displays RF coverage details. The W-IAP uses this metric to measure RF coverage. The coverage index is calculated as x+y, where “x” is the W-IAP’s weighted calculation of the Signal-to- Noise Ratio (SNR) on all valid APs on a specified 802.11 channel, and “y” is the weighted calculation of the W-IAPs SNR detected by the neighboring APs on that channel. intf_idx(Total Displays channel interference details.
36 2483300 1530 0 0 DVACFT 172120 40 576170 1547 0 0 DVACPT 172139 44 9945940 1454 0 0 DVACFT 172145 48 170500 1550 0 0 DVACPT 172158 52 167420 1522 0 0 DVACT 172046 56 65450 595 0 0 DVCT 171880 60 169840 1544 0 0 DVACT 172052 64 170390 1549 0 0 DVACT 172063 149 68631720 952 0 0 DVACFT 172074 153 32278480 1268 0 0 DVACPT 172088 157 38634770 1207 0 0 DVACFT 172132 161 20620710 1361 0 0 DVACPT 172161 165 170280 1548 0 0 DVACT 172110 1 86424330 903 0 0 DVACFT 172161 2 53570 487 0 0 DC 171936 3 55660 506 0 0 DC
Column Description flags Indicates channel flags. For more information on channel flags, see the flag description below the channel scan time table. timer-tick Indicates the time interval since the last scan. Scan mode Indicates if the scan mode enabled on the Wi-Fi interface. channel (under WIFI Scanning State) Indicates the channels available on the Wi-Fi interface. current-scan-channel Indicates the current channel scanned.
show ap association show ap association Description This command displays the association table for an AP group or for an individual W-IAP. Usage Guidelines Use this command to view information about the clients associated with a W-IAP. Example The following example shows the output of show ap association command. The phy column shows client's operational capabilities for current association Flags: A: Active, B: Band Steerable, H: Hotspot(802.11u) client, K: 802.11K clie nt, R: 802.
Column Description vlan-id Indicates the VLAN ID associated with the W-IAP. tunnel-id Indicates the identification number of the W-IAP tunnel. assoc. time Indicates the amount of time the client has been associated with the W-IAP, in the hours:minutes:seconds format. num assoc Indicates the number of clients associated with the W-IAP. flags Displays flags for this W-IAP if any. For information on flag abbreviations, see the flag description at beginning of the output.
show ap bss-table show ap bss-table Description This command displays an AP’s Basic Service Set (BSS). Usage Guidelines The output of the show ap bss-table command shows the Dell AP BSS table for all APs. To filter this information and view BSS table data for an individual AP or a specific port and slot number, include the apname, bssid, essid, ip-addr or port keywords.
Column Description ch/EIRP/max-EIRP Displays the radio channel used by the AP/current effective Isotropic Radiated Power (EIRP) /maximum EIRP. cur Displays the current number of clients on the AP. Command History Version Description Dell Networking WSeries Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ap client-match-history show ap client-match-history [client-mac ] Description This command displays a historical record of the client match events and actions for the clients associated with a W-IAP. Syntax Parameter Description client-mac Allows you to filter the output based on a client MAC address. When the client MAC address is specified and the command is executed, the client match actions pertaining to the specified client is displayed.
Command History Version Description Dell Networking W-Series Instant 6.3.1.1-4.0 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ap client-match-live show ap client-match-live Description This command displays the current client match events and actions for clients associated with a W-IAP. Usage Guidelines Use this command to view the current clients match actions for the clients associated with a W-IAP. Example The following example shows the output of the show ap client-match-live command.
show ap client-probe-report show ap client-probe-report [] Description This command displays the client probe report for a W-IAP. Syntax Parameter Description Allows you to filter the output based the ID number of the radio (for example, 0 or 1). Usage Guidelines Use this command to view a probe report for the clients associated with a W-IAP. Example The following example shows the output of the show ap client-probe-report command.
00:21:6a:ba:b7:ce 04:0c:ce:e1:98:78 00:1e:65:71:18:de 60:67:20:4d:e8:a8 b4:b6:76:42:49:56 b4:b6:76:42:49:1f c4:85:08:d4:79:48 b4:b6:76:42:49:4c b4:b6:76:42:49:6a c8:f7:33:a3:69:2f c8:f7:33:a0:a9:6f b4:b6:76:42:49:47 00:0b:6b:b1:79:f5 58:94:6b:36:5a:58 c8:f7:33:a4:9a:39 c8:f7:33:a4:5a:dd c8:f7:33:a4:5a:2e c8:f7:33:a4:5a:c9 b4:b6:76:42:5a:9f 7c:d1:c3:8a:6b:be 00:26:c6:52:6b:14 58:94:6b:36:cb:e8 c4:85:08:db:db:e8 b4:b6:76:42:5b:3f b4:b6:76:42:5b:44 ac:81:12:59:5c:12 00:1e:e5:e4:ec:d0 3c:a9:f4:1d:ac:a4 00:03:7f
show ap client-match-refused show ap client-match-refused [] Description This command displays the list of clients for which the channel allocation is refused based on the client match configuration parameters. Syntax Parameter Description Allows you to filter the output based the ID number of the radio (for example, 0 or 1). Usage Guidelines Use this command to view the list of clients for which client match actions are refused.
Command History Version Description Dell Networking W-Series Instant 6.3.1.1-4.0 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ap client-match-triggers show ap client-match-triggers Description This command displays the configuration conditions that trigger client match events and actions for the clients associated with a W-IAP. Usage Guidelines Use this command to view the clients match trigger records. When the client match feature is enabled on a IAP, the W-IAP measures the RF health of its associated clients.
Command History Version Description Dell Networking W-Series Instant 6.4.0.2-4.1 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ap client-view show ap client-view Description This command displays information about the clients in the AP neighborhood. Usage Guidelines Use this command to view information about the clients associated with the neighboring W-IAPs.
Command History Version Description Dell Networking W-Series Instant 6.3.1.1-4.0 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ap debug airwave show ap debug airwave Description This command displays the list of W-AirWave servers configured on a W-IAP. Usage Guidelines Use this command to view the list of W-AirWave servers configured for a W-IAP. Example The following example shows the output of show ap airwave command: Airwave Server List ------------------Domain/IP Address Type Mode Status ---------- ---- ---- -----test.com Primary - Not connected test1.
show ap debug airwave-config-received show ap debug airwave-config-received Description This command indicates if any configuration information is received by the W-IAP from the W-AirWave server. Usage Guidelines Use this command to view if any configuration information is received from the W-AirWave server.
show ap debug airwave-data-sent show ap debug airwave-data-sent Description This command displays information about data exchange between the W-AirWave server and the W-IAP. Usage Guidelines Use this command to view information about the data sent to the W-AirWave server. Example The following example shows the output of the show ap debug airwave-data-sent command: cat: /tmp/awc_buf.txt: No such file or directory Command History Version Description Dell Networking W-Series Instant 6.2.1.03.
show ap debug airwave-events-pending show ap debug airwave-events-pending Description This command displays the pending W-AirWave server events. Usage Guidelines Use this command to view the pending W-AirWave server events.
show ap debug airwave-signon-key show ap debug airwave-signon-key Description This command displays the W-AirWave sign on key used by the used by the administrator to manually authorize the first Virtual Controller for an organization. Usage Guidelines Use this command to view the W-AirWave sign on key details for debugging purpose.
show ap debug airwave-state show ap debug airwave-state Description This command displays the configuration details and status of W-AirWave events associated with a W-IAP. Usage Guidelines Use this command to view the current state of W-AirWave events associated with the W-IAP. Example The following example shows the output of the show ap debug airwave-state command: fc6520ad018ee6eb13bdc6b985e0fe6361bd37f7d25212a77e Instant-C4:42:98 0.0.0.0 6.2.0.0-3.3.0.
93 3 d8:c7:c8:c4:29:80 1 22 1 0 80 61 Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ap debug airwave-stats show ap debug airwave-stats Description This command displays the configuration statistics associated with a W-IAP managed or monitored by the WAirWave server. Usage Guidelines Use this command to view configuration details of a W-IAP managed or monitored by the W-AirWave server.
show ap debug am-config show ap debug am-config Description This command displays the information required for debugging a W-IAP. Syntax Parameter Description mac MAC address in the trace buffer.
Frame Receive Error Rate Low Watermark 0 Frame Retry Rate High Watermark 0 Frame Retry Rate Low Watermark 0 Interference Configuration -------------------------Parameter Value --------- ----Detect Interference Disable Interference Increase Threshold 0 Interference Increase Timeout 0 Interference Wait Time 0 IDS General Configuration Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced.
show ap debug auth-trace-buf show ap debug auth-trace-buf [] Description This command displays the trace buffer for authentication events associated with the W-IAP. Syntax Parameter Description Displays the authentication trace information for a specific MAC address. Usage Guidelines Use the output of this command to troubleshoot authentication errors. Include the parameter to filter data by the MAC address of the client to view specific details.
Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ap debug client-match show ap debug client-match Description This command displays the information about the client match configuration status on an AP radio interface. Syntax Parameter Description Allows you to specify the ID number of the radio (for example, 0 or 1) for which you want to view client match configuration status. Usage Guidelines Use this command to view the status of client match configuration for a specific radio interface.
show ap debug client-stats show ap debug client-stats Displays data based on the client MAC address. Usage Guidelines Use this command to view information about a W-IAP client.
Rx Data Frames Null Data Frames Rx Mgmt Frames PS Poll Frames Rx 6 Mbps Rx 12 Mbps Rx 18 Mbps Rx 24 Mbps Rx 36 Mbps Rx 48 Mbps Rx 54 Mbps Rx WMM [BE] 2930 2879 1 0 14 6 5 2 13 1162 1730 39 The output of this command includes the following information: Parameter Description Frames Rcvd For TX Shows the number of frames received for transmission. Tx Frames Dropped Shows the number of transmission frames that were dropped. Frames Transmitted Shows the number of frames successfully transmitted.
Parameter Description Tx WMM [VI]: Video UAPSD OverflowDrop Shows the number of packets dropped due to Unscheduled Automatic Power Save Delivery (U-APSD) overflow. Last SNR Indicates the last recorded signal-to-noise ratio. Last SNR CTL0 Indicates the signal-to-noise ratio for the last received data packet on the primary (control) channel 0. This parameter is only displayed for APs operating in 40 MHz mode.
Parameter Description Rx Mbps Shows the number of frames received at Mbps, where is a value between 6 and 300. Tx WMM Shows the number of Wi-Fi Multimedia (WMM) packets transmitted for the following access categories. If the AP has not transmitted packets in a category type, this data row will not be displayed in the output of the command.
show ap debug client-table show ap debug client-table Description This command shows the clients associated with a W-IAP. Usage Guidelines Use this command to view a list of W-IAP clients.
Parameter Description UAPSD Shows the following values for Unscheduled Automatic Power Save Delivery (UAPSD) in comma-separated format: VO, VI, BK, BE, Max SP, Q Len. l VO: If 1, UAPSD is enabled for the VoIP access category. If UAPSD is disabled for this access category, this value is 0. l VI: If 1, UAPSD is enabled for the Video access category. If UAPSD is disabled for this access category, this value is 0. l BK: If 1, UAPSD is enabled for the Background access category.
show ap debug crash-info show ap debug crash-info Description This command displays log information for a W-IAP that crashed. The stored crash information is cleared from the flash after the W-IAP reboots. Syntax No parameters Usage Guidelines Use this command to view the W-IAP crash information for debugging purpose. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced.
show ap debug dhcp-packets show ap debug dhcp-packets Description This command displays information about the DHCP packets sent or received by a W-IAP. Usage Guidelines Use this command to view information about the DHCP packets trace information for a W-IAP.
show ap debug dot1x-statistics show ap debug dot1x-statistics Description This command displays the aggregate 802.11X debug statistics for a W-IAP. Usage Guidelines Use this command to view information about the 802.11x authentication. Example The following output is displayed for the show ap debug dot1x-statistics command: 802.
Parameter Description MkeyRot Displays the multicast key rotation details. 802.1X counters Displays the 802.1X authentication counters. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ap debug driver-config show ap debug driver-config Description This command displays W-IAP driver configuration. Usage Guidelines Use this command to review configuration changes made since the W-IAP driver was last reset. Example The show ap debug driver-config command displays the BSSID, SSID, and radio configuration details associated with the W-IAP driver.
Honor 40 MHz intolerance Enabled CSD override Enabled Advertise 802.
Max received A-MPDU size 65535 bytes Max transmitted A-MPDU size 65535 bytes Min MPDU start spacing 16 usec Short guard interval in 20 MHz mode Enabled Short guard interval in 40 MHz mode Enabled Supported MCS set Explicit Transmit Beamforming Disabled Transmit Beamforming Compressed Steering Disabled Transmit Beamforming non Compressed Steering Disabled Transmit Beamforming delayed feedback support Disabled Transmit Beamforming immediate feedback support Disabled Transmit Beamforming Sounding Interval 0 se
show ap debug mgmt-frames show ap debug mgmt-frames Description This command displays the trace information for the 802.11 management frames. Syntax Parameter Description Displays trace information for a W-IAP based on MAC address. Example The following example shows the partial output of show ap debug mgmt-frames command: Traced 802.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ap debug persistent-clients show ap debug persistent-clients Description This command displays the information about the persistent W-IAP clients. Usage Guidelines Use this command to view information about the clients that are persistently connected to a W-IAP.
show ap debug radio-stats show ap debug radio-stats [] Description This command displays the aggregate radio debug statistics of a W-IAP. Syntax Parameter Description Allows you to specify the ID number of the radio (for example, 0 or 1) for which you want to view statistics. Usage Guidelines Use this command to view the radio debug statistics for a W-IAP.
Tx Data Bytes 108 Mbps (Mon) 0 RADIO Stats ----------Parameter Value --------- ----Tx Data Bytes 108 Mbps+ (Mon) 0 Tx 6 Mbps 557650 Tx WMM [BE] 125 Tx WMM [VO] 557532 Tx WMM [BE] Dropped 158561 Tx UAPSD OverflowDrop 0 TX Timeouts 36 Lost Carrier Events 8 Tx HT40 Hang Detected 0 Tx HT40 Hang Stuck 0 Tx HT40 Hang Possible 0 Tx HT40 Dfs IMM WAR 0 Tx HT40 Dfs HT20 WAR 0 Tx MAC/BB Hang Stuck 0 Tx Mgmt Bytes 1434583125 Tx Beacons Bytes 1202571538 ------------------- Receive Specific Statistics Rx Last SNR 16 Rx L
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ap debug radius-statistics show ap debug radius-statistics Description This command displays the RADIUS statistics for the authentication servers configured on a W-IAP. Usage Guidelines Use this command to view the authentication server details. Example The output of this command displays general statistics of the authentication servers configured on a W-IAP.
show ap debug shaping-table show ap debug shaping-table Description This command displays the shaping information for clients associated to a W-IAP. Usage Guidelines Use this command to view the shaping information for clients connected to a W-IAP.
Column Description last-t Shows the number of tokens that were allocated to the station last time token allocation algorithm ran. in Shows the number of packets received. out Shows the number of packets sent. drop Shows the number of dropped packets. q Shows the number of queued packets tx-t Shows the total time spent transmitting data. rx-t Shows the total time spent receiving data. al-t Shows the total time allocated for transmitting data to this station.
show ap debug spanning-tree show ap debug spanning-tree Description This command displays the Spanning Tree Protocol (STP) information for a W-IAP. Usage Guidelines Use this command to view STP details on a W-IAP. STP is enabled for a wired port profile to ensure that there are no loops in any bridged Ethernet network. STP operates on all downlink ports, regardless of forwarding mode. STP will not operate on the uplink port and is supported only on W-IAPs with three or more ports.
show ap debug stm-config show ap debug stm-config Description This command displays the W-IAP station management configuration information. Usage Guidelines Use this command to view the details of station management configuration.
show ap debug system-status show ap debug system-status Description This command displays the detailed system configuration information for a W-IAP. Usage Guidelines Use this command under the guidance of Dell technical support to troubleshoot network issues.
show ap dot11k-beacon-report show ap dot11k-beacon-report Description This command displays the beacon report details for the 802.11k clients of a W-IAP. Syntax Parameter Description Allows you to specify the MAC address of the client for which you want to view the beacon report details. Usage Guidelines Use this command to view the beacon report details for 802.11k clients connected to a W-IAP.
show ap dot11k-nbrs show ap dot11k-nbrs Description This command displays the neighboring details of the 802.11k clients connected to a W-IAP. Usage Guidelines Use this command to view neighbors of the 802.11k clients connected to a W-IAP.
show ap flash-config show ap flash-config Description This command shows the statistics of the W-IAP configuration stored in flash memory. Usage Guidelines Use this command to view the configuration details in the flash memory. Example The following example shows the output of show ap flash-config command: IP Address: 10.15.20.252 Network Mask:10.15.22.257 Gateway IP:10.15.20.255 DNS Server: 92.168.1.10 Domain Name: floor1.test.
show ap mesh counters show ap mesh counter Description This command displays the mesh counters for a W-IAP. Usage Guidelines Use this command to view a list of mesh counters available for a W-IAP. Example The following example shows the output of show ap mesh counter command. Mesh Packet Counters -------------------Interface Echo Sent Echo Recv Probe Req Probe Resp Assoc Req Assoc Resp Assoc Fail Link up/down Resel.
Column Description Echo Sent Number of echo packets sent. Echo Recv Number of echo packets received. Probe Req Number of probe request packets sent from the interface specified in the MeshIF parameter. Probe Resp Number of probe response packets sent to the interface specified in the Interface parameter. Assoc Req Number of association request packets from the interface specified in the Interface parameter.
show ap mesh link show ap mesh link Description This command shows the mesh link of the W-IAP. Example The following example shows the output of show ap mesh link command: (Instant AP)# show ap mesh link Neighbor list ------------MAC Portal Channel Age Hops Cost Relation Flags RSSI Rate Tx/Rx --- ------ ------- --- ---- ---- -------- ----- ---- ---------00:0b:86:e8:09:d1 00:1a:1e:88:01:f0 157 0 1 11.00 C 3h:15m:42s 54/54 00:1a:1e:88:02:91 00:1a:1e:88:01:f0 157 0 1 4.
Parameter Description and the amount of time that relationship has existed. l P = Parent l C = Child l N = Neighbor l B = Blacklisted-neighbor Flags This parameter shows additional information about the mesh neighbor. The key describing each flag is displayed at the bottom of the neighbor list. RSSI The Receive Signal Strength Indicator (RSSI) value displayed in the output of this command represents signal strength as a signal to noise ratio.
show ap mesh neighbors show ap mesh neighbors Description This command shows all mesh neighbors for an AP. Example The following example shows the output of show ap mesh neighbors command: Neighbor list ------------MAC Portal Channel Age Hops Cost Relation Flags RSSI Rate Tx/Rx A-Req A-Resp A-Fail HT-Details Cluster ID --- ------ ------- --- ---- ---- -------- ----- ---- ---------- ----- ------ ------ ------------------6c:f3:7f:a5:df:90 Yes 157 23 0 5.
Parameter Description and the amount of time that relationship has existed. l P = Parent l C = Child l N = Neighbor l B = Blacklisted-neighbor Flags This parameter shows additional information about the mesh neighbor. The key describing each flag is displayed at the bottom of the neighbor list. RSSI The Receive Signal Strength Indicator (RSSI) value displayed in the output of this command represents signal strength as a signal to noise ratio.
show ap monitor show ap monitor {active-laser-beams|ap-list|ap-wired-mac |arp-cache| containment-info | enet-wired-mac | ids-state | pot-ap-list | pot-sta-list | routers | scan-info | sta-list | state | stats | status} Description This command shows information for W-IAP Air Monitors. Syntax Parameter Description active-laser-beams Shows active laser beam generators.
Parameter Description ids-state Shows IDS State. pot-ap-list Display the Potential AP table. The Potential AP table shows the following data: l bssid: the AP’s Basic Service Set Identifier. l channel: The AP’s current radio channel l phy type: The radio’s PHY type. Possible values are 802.11a, 802.11a-HT-40, 802.11b/g, 802.11b/g-HT-20. l num-beacons: Number of beacons seen during a 10-second scan l tot-beacons: Total number of beacons seen since the last reset.
Active Laser Beam Sources ------------------------bssid channel rssi ap name lms ip master ip inactive time ----- ------- ---- ------- ------ --------- ------------- show ap monitor ap-list The following example shows the output of show ap monitor ap-list command: Monitored AP Table -----------------bssid essid chan ap-type phy-type dos dt/mt ut/it encr nstas avg-rssi curr-rssi wmacs ibss ----- ----- ---- ------- -------- --- ----- ----- ---- ----- -------- --------- ----- ---d8:c7:c8:3d:3a:93 rahul_wep 14
mac ip vlanid age --- -- ------ --d8:c7:c8:cb:d4:20 10.17.88.188 0 1s d8:c7:c8:cb:d3:d4 10.17.88.186 0 1s 00:0b:86:40:1c:a0 10.17.88.
show ap monitor pot-sta-list The following example shows the output of show ap monitor pot-sta-list command.
show ap monitor state The following example shows the output of show ap monitor state command. DoS State ---------tx old-tx rx old-rx last-dos-time ap-ev-time sta-ev-time last-enhanced-cm-time enhanced-cm-evtime -- ------ -- ------ ------------- ---------- ----------- --------------------- -----------------0 0 0 0 0 0 0 0 0 show ap monitor stats The following example shows the output of show ap monitor stats command.
---- ------ ------- ------ ------- ------- -------- ------- -------- ------- -------- -------------- ------- -------- ------- -------tx 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rx 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 HT RX Rate Stats ---------------Rate Pkts Bytes ---- ---- ----HT TX Rate Stats ----------------Rate Pkts Bytes ---- ---- ----Detailed RSSI ------------10s 2m 3m 4m 5m 6m 7m 8m 9m 10m 11m 12m 13m 14m 15m - --- -- -- -- -- -- -- -- -- --- --- --- --- --- --average 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 h
d8:c7:c8:3d:42:00(wifi1) 56090990 3565742575 50110266 13315 1024 275 20 1 0 Data Structures ---------------ap sta pap psta ch msg-hash ap-l -- --- --- ---- -- -------- ---256 288 45 136 26 2 256 Other Parameters ----------------key value --- ----Classification enable Wireless Containment disable Wired Containment disable Rogue Containment disable System OUI Table ----------------oui --RTLS Configuration and State ----------------------------Type Server IP Port Freq Active Rpt-Tags Tag-Mcast-Addr Tags-Sent R
show ap pmkcache show ap pmkcache Description This command displays the pairwise master key (PMK) cache table for clients associated with the W-IAP. Usage Guidelines Use this command to view PMK cache table contents for the clients associated with a W-IAP. Example The following example shows the output of show ap pmkcache command. PMK Cache Table --------------Client MAC ---------00:90:7a:0d:a0:62 00:90:7a:0d:b2:ce Key OKC/11r Expiry --------- -----1F4C17D8A70C...okc 6h:52m:18s F20E35DB311F...
show ap virtual-beacon-report show ap virtual-beacon-report Description This command displays a report with the MAC address details and RSSI information of a W-IAP. Usage Guidelines Use this command to view virtual beacon table of a W-IAP. The virtual beacon table with the details of clients associated a W-IAP is broadcast by each table. Example The following example shows the output of show ap virtual-beacon-report command.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show app-services show app-services Description This command displays the list of application services available on a W-IAP. Usage Guidelines Use this command to view the list of application services available on a W-IAP.
smtp 6 25 25 snmp 17 161 161 snmp-trap 17 162 162 ssh 6 22 22 svp 119 0 65535 syslog 17 514 514 telnet 6 23 23 tftp 17 69 69 vocera 17 5002 5002 The output of this command provides the following information: Parameter Description Name Indicates the list of application services available on a W-IAP. IP Protocol Displays the IP protocol numbers for each application service. Start Port and End Port Indicates the range of port numbers on which the application services are enabled.
show arm-channels show arm-channels Description This command displays the ARM channel details configured on a W-IAP. Usage Guidelines Use this command to view the channel details configured on a W-IAP. Example The following example shows the output of show arm-channels command: 2.
157+ enable The output of this command provides the following information: Parameter Description Channel Displays the list of channels available in the 2.4 GHz and 5 GHz bands. Status Indicates if the channels in the 2.4 GHz and 5 GHz bands are enabled or disabled. Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced.
show arm config show arm config Description This command displays the ARM configuration details for a W-IAP. Usage Guidelines Use this command to view the ARM configuration details for a W-IAP.
60 enable 64 enable 149 enable 153 enable 157 enable 161 enable 165 enable 36+ enable 44+ enable 52+ disable 60+ disable 149+ enable 157+ enable The output of this command provides the following information: Parameter Description Minimum Transmit Power Displays the minimum transmission power configured for the ARM channels. Maximum Transmit Power Displays the maximum transmission power configured for the ARM channels.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show arp show arp Description This command displays the Address Resolution Protocol (ARP) entries for the Virtual Controller. Usage Guidelines Use this command to view the ARM messages sent or received by the Virtual Controller. Example The following example shows the output of show arp command IP address HW type Flags HW address Mask Device 192.168.10.2 0x1 0x6 D8:C7:C8:C4:42:98 * br0 10.17.88.
show attack show attack {config| stats} Description This command displays information about firewall settings configured on a W-IAP to protect the network against wired attacks such as ARP attacks or malformed DHCP packets. Syntax Parameter Description config Displays firewall configuration details to protect the network from wired attacks. stats Displays attack counters.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show auth-survivability show auth-survivability {cached-info| debug-log []| time-out} Description This command displays the authentication survivability information for a W-IAP. Syntax Command/Parameter Description cached-info Displays authentication credentials cached by the W-IAP. debug-log [] Displays the log details for troubleshooting. The count attribute allows you to specify the number of logs to display. time-out Displays the duration configured for the cache expiry.
Command History Version Description Dell Networking W-Series Instant 6.4.0.2-4.1 This command was modified. Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show backup-config show backup-config Description This command displays the backup configuration information on a W-IAP, Usage Guidelines Use this command to view the current configuration information stored in the W-IAP flash memory. Example The following text provides an example for the show backup-config command output: version 6.4.0.0-4.1.
blacklist-time 3600 auth-failure-blacklist-time 3600 ids classification ids wireless-containment none airgroup disable airgroupservice airplay disable description AirPlay airgroupservice airprint disable description AirPrint Command History Version Description Dell Networking W-Series Instant 6.4.0.24.1 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show blacklist-client show blacklist-client [config] Description This command shows the configuration details for blacklisting clients and lists the clients blacklisted by W-IAP. Syntax Parameter Description config Displays the parameters and values configured for manual or dynamic blacklisting of clients. Usage Guidelines Use this command to view information about the clients blacklisted by a W-IAP.
Parameter Description Dynamically Blacklisted Clients Displays the list of clients that dynamically blacklisted due to multiple authentication rules or an ACL rule trigger. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show calea config show calea config Description This command displays the details configured for CALEA server integration on a W-IAP. Usage Guidelines Use this command to CALEA configuration details. Example The following example shows the output of the show calea config command: (Instant AP)# show calea config calea-ip :10.0.0.5 encapsulation-type :gre gre-type :25944 ip mtu : 150 Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.4 This command is introduced.
show calea statistics show calea statistics Description This command displays the tunnel encapsulation statistics for a W-IAP. Usage Guidelines Use this command to view the GRE encapsulation statistics for the W-IAPs with CALEA server integration feature enabled.
show captive-portal show captive-portal Description This command shows the external and internal captive portal parameters configured for a network profile. Usage Guidelines Use this command to view information about the contents displayed on the internal and external captive portal pages for guest users.
Parameter Description Server Displays the external Captive port server. URL Displays the URL of the external captive portal splash page server. Authentication Text Indicates if the external captive portal user authentication is successful. Port Displays the port used for communicating with the external captive portal splash page server. Server Fail Through Indicates if the guest clients are allowed to access the Internet when the external captive portal server is not available.
show captive-portal-domains show captive-portal-domains Description This command displays the internal and external captive portal server domains. Usage Guidelines Use this command to view information about the internal and external captive portal domains. Example The following output is displayed for the show captive-portal-domains command: Internal Captive Portal Domain: securelogin.arubanetworks.
show cellular show cellular {config | status} Description These commands display the status and cellular configuration of the W-IAP. Syntax Parameter Description show cellular config Displays the cellular configuration details available for the W-IAP show cellular status Displays the status of the cellular configuration for the W-IAP Usage Guidelines Use these commands to view the details of the cellular configuration and status.
Canada Supported ISP list -----------------ISP list -------Cincinnati Bell Virgin Telecom Telenor Vodafone/SmarTone O2 SFR Orange 3/HUTCH Optus SingTel HKCSL/1010 Verizon ICE Reliance NetConnect+ Tata Indicom Airtel-3G Nokia CS-10 NTT KDDI Movistar China Unicom China Telecom Vodafone Netcom T-Mobile Telstra Mobily EMOBILE Sprint Cricket Vodafone-3G Airtel ATT Rogers Bell modem status summary:No USB modem attached The output of this command includes the following parameters: Parameters Description type D
Not-present Not-detect Linkdown The output of this command includes the following parameters: Parameters Description Card Indicates if the cellular cards are currently configured on the W-IAP. detect Indicates if cellular modems are detected on the W-IAP Link Indicates the current status of cellular link. Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced.
show cert all show cert all Description This command displays the details about the certificates uploaded on a W-IAP. Usage Guidelines Use this command to view information about the certificates uploaded to a W-IAP. Example The following example shows the output of show cert command: Default Server Certificate: Version :3 Serial Number :01:DA:52 Issuer :C=US, O=GeoTrust Inc., OU=Domain Validated SSL, CN=GeoTrust DV SSL CA Subject :0x05=lLUge2fRPkWcJe7boLSVdsKOFK8wv3MF, C=US, O=securelogin.arubanetworks.
show clients show clients [| accounting | checksum | debug| roaming| status | wired [debug]] Description This command displays details about the W-IAP clients. Syntax Parameter Description Displays difference summary of the client table since the specified interval. accounting Displays accounting information for a specific client MAC address. checksum Filters checksum errors for a specific client MAC address.
Column Description Name Displays the name of the client IP address Displays the IP address of the client. MAC address Displays the MAC address of the client. OS Indicates the OS running on the client system. Network Indicates the SSID and network to which the client is connected. Access Point Indicates the IP address of the Access Point to which the client is connected. Channel Indicates the channel assigned to the client. Type Indicates the type of the Wi-Fi client device.
00 8a acct_session 00 00 00 00 00 00 00 00 00 00 00 00 00 00 user_role 00 00 00 00 00 00 00 00 00 00 00 00 00 00 swarm_basic_client_t 08 ed b9 e1 51 7d d8 00 00 00 00 00 00 00 checksum 02 ec ba ec 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c7 c8 3d 3d 52 0a 11 58 ba 73 72 6f 79 2d 73 6f 6d 65 74 68 69 6e 67 00 00 00 00 00 00 00 00 00 00
Command History Version Description Dell Networking W-Series Instant 6.3.1.1-4.0 This command was modified. Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show clock show clock [summer-time| timezone all] Description This command displays the system clock, current timezone, and the daylight saving time configured on a W-IAP Syntax Parameter Description summer-time Displays the summer (daylight saving) time settings. timezone all Displays the configured timezone for the W-IAP. Usage Guidelines Use this command to display the system clock. Include the optional summer-time parameter to display configured daylight savings time settings.
Parameter Description Country Displays the country name. Timezone Displays the name of the timezone. DST Name Displays the name of the Daylight Saving Time. DST Recurring Displays the name of the Daylight Saving recurring time.
Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show configuration show configuration Description This command displays the configuration saved on the W-IAP. Usage Guidelines Use this command to view the entire configuration saved on the W-IAP, including all wireless and wired profiles, uplink configuration, ARM settings, radio profiles, ACLs, and interface settings. Example The following example displays the show configuration command output: version 6.2.1.0-3.3.0.
nai-realm-eap-method eap-ttls nai-realm-auth-id-1 non-eap-inner-auth nai-realm-auth-value-1 mschapv2 nai-realm-auth-id-2 credential nai-realm-auth-value-2 uname-passward nai-realm-encoding utf8 no nai-home-realm hotspot anqp-nwk-auth-profile "test" enable nwk-auth-type http-redirect url "http:///" hotspot anqp-3gpp-profile "test" enable 3gpp-plmn1 "" 3gpp-plmn2 "" 3gpp-plmn3 "" 3gpp-plmn4 "" 3gpp-plmn5 "" 3gpp-plmn6 "" hotspot anqp-ip-addr-avail-profile "test" enable ipv4-addr-avail no ipv6-addr-avail hotsp
captive-portal disable dtim-period 1 inactivity-timeout 1000 broadcast-filter none external-server bandwidth-limit 65535 dmo-channel-utilization-threshold 90 local-probe-req-thresh 0 max-clients-threshold 64 wlan ssid-profile profile-local-nw enable index 1 type employee essid profile-local-nw wpa-passphrase dd4da86c25c31bf83417024a338982ed4f01e1751e7a4502 opmode wpa2-psk-aes max-authentication-failures 0 vlan 2 auth-server InternalServer rf-band all captive-portal disable dtim-period 1 inactivity-timeout 1
native-vlan 1 shutdown access-rule-name default_wired_port_profile speed auto duplex full no poe type employee captive-portal disable no dot1x enet0-port-profile default_wired_port_profile uplink preemption enforce none failover-internet-pkt-lost-cnt 10 failover-internet-pkt-send-freq 30 failover-vpn-timeout 180 airgroup enable airgroupservice airplay disable description AirPlay airgroupservice airprint disable description AirPrint Command History Version Description Dell Networking W-Series Instant 6.2.
show config-status show config-status Description This command displays the details about the configuration status of a W-IAP. Usage Guidelines Use this command to view the current configuration status of the W-IAP in flash memory. Example The following example shows the output of the show config-status command: Config Status ------------Config Name Compressed ----------- ---------Primary No Backup No The backup configuration is used when the primary configuration is lost.
show console-settings show console-settings Description This command displays the details about the console settings of a W-IAP. Usage Guidelines Use this command to view if the access to W-IAP console is enabled or disabled. Example The following example shows the output of the show console-settings command: (Instant AP)# show console-settings Console Setting --------------Status -----enabled Command History Version Description Dell Networking W-Series Instant 6.4.0.24.1 This command is introduced.
show country-codes show country-codes Description This command shows the country code for the W-IAP. The country code specifies allowed channels for that country. Usage Guidelines Use this command to view a list of W-IAP country codes. Example The following example shows the output of show country-codes command .
PR:Puerto Rico SK:Slovak Republic SI:Slovenia TH:Thailand UY:Uruguay PA:Panama RU:Russia EG:Egypt TT:Trinidad and Tobago TR:Turkey CR:Costa Rica EC:Ecuador HN:Honduras KE:Kenya UA:Ukraine VN:Vietnam BG:Bulgaria CY:Cyprus EE:Estonia MT:Malta MU:Mauritius RO:Romania CS:Serbia and Montenegro ID:Indonesia PE:Peru VE:Venezuela JM:Jamaica BH:Bahrain OM:Oman JO:Jordan BM:Bermuda CO:Colombia DO:Dominican Republic GT:Guatemala PH:Philippines LK:Sri Lanka SV:El Salvador TN:Tunisia MO:Macau PK:Islamic Republic of Paki
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show cpcert show 1xcert Description This command displays the details of the captive portal server certificate, which is used by the W-IAP for guest authentication. Usage Guidelines Use this command to view information about the captive portal server certificate uploaded on W-IAP.
show cpu show cpu [details] Description This command displays the CPU details. Syntax Parameter Description [details] Include this optional parameter at the request of Dell technical support to display additional CPU troubleshooting statistics. Usage Guidelines Use this command to view CPU load for application and system processes.
Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show datapath show datapath {acl |acl-all|acl-allocation|acl-rule |acl-ruledetail|bridge|dmo-session|dmo-station |mcast|nat-pool |route session|statistics|user|vlan} Descriptions This command shows the system statistics for your W-IAP. Syntax Parameter Description acl Displays datapath statistics associated with a specified ACL. acl-all Displays datapath statistics associated with all ACLs. acl-allocation Displays ACL table allocation details.
Datapath ACL 3 Entries ----------------------Flags: P - permit, L - log, E - established, M/e - MAC/etype filter S - SNAT, D - DNAT, R - redirect, r - reverse redirect m - Mirror I - Invert SA, i - Invert DA, H - high prio, O - set prio, C - Classify Media A - Disable Scanning, B - black list, T - set TOS, 4 - IPv4, 6 - IPv6 ---------------------------------------------------------------- show datapath acl-all The following example shows the output of show datapath acl-all command.
105 103 107 104 108 100 101 102 134 135 136 143 145 130 131 132 133 137 139 141 146 147 148 149 150 151 152 153 138 140 142 144 106 3200 3234 3250 3282 3298 3330 3332 3336 3340 3344 3352 3360 3372 3380 3412 3444 3476 3508 3520 3532 3540 3544 3552 3556 3564 3568 3572 3576 3580 3588 3596 3604 3612 32 16 32 16 32 2 4 4 4 8 4 8 8 16 16 16 16 8 8 8 4 8 4 8 4 4 4 4 8 8 8 8 8 show datapath acl-rule The following example shows the output of show datapath acl-rule command.
4: 192.168.10.0 255.255.254.0 any any PST4 5: any any any PT4 ---------------------------------------------------------------ACL Name {test 3} Number {145} 1: any any 17 0-65535 8209-8211 P4 2: 192.168.10.0 255.255.254.0 192.168.10.0 255.255.254.0 any PT4 3: 192.168.10.0 255.255.254.0 224.0.0.0 224.0.0.0 any PT4 4: 192.168.10.0 255.255.254.
dev11 dev12 dev13 dev14 1 1 1 1 show datapath nat-pool The following example shows the output of show datapath nat-pool command. Datapath NAT Pool Entries ------------------------ID Begin Source IP End Source IP Destination IP Flags -- --------------- ------------- -------------- ----- show datapath route The following example shows the output of show datapath route command.
Tagged frames dropped on untagged interface 0 Frames dropped for being too short 0 Frames received on port not in VLAN 0 Non-dot1x frames dropped during L2 blocking 0 Frames dropped for ingress change on permanent bridge entry 0 Frames received on port not in VLAN 0 Unicast frames filtered 86 Frames dropped due to FP firewall 6 Frames that failed FP spoofing check 0 Frames dropped with logging 0 Frames dropped due to unknown FP opcode 0 Frames freed by FP 3 Frames that failed SP spoofing check 0 Frames drop
show datapath user The following example shows the partial output of show datapath user command. Datapath User Table Entries --------------------------Flags: P - Permanent, W - WEP, T- TKIP, A - AESCCM R - ProxyARP to User, N - VPN, L - local FM(Forward Mode): S - Split, B - Bridge, N - N/A IP MAC ACLs Contract Location Age Sessions Flags Vlan FM --------------- ----------------- ------- --------- -------- ----- --------- ----- ---- -10.17.88.59 D8:C7:C8:C4:42:98 105/0 0/0 0 0 1/65535 1 N 0.0.0.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show delta-config show delta-config cfgid Description This command displays the difference between the current configuration in the current CLI session and the configuration that is saved on the W-IAP. Usage Guidelines Use this command to view the difference between the current configuration information stored in the W-IAP flash memory and the configuration information saved in the W-IAP memory.
show derivation-rules show derivation-rules Description This command displays the list of role and VLAN derivation rules configured for the WLAN SSIDs and wired profiles in a W-IAP. Usage Guidelines Use this command to view the derivation rules configured for a network profile.
show dhcp-allocation show dhcp-allocation Description This command displays information about the DHCP address allocation. Usage Guidelines Use this command to view DHCP address allocation for network address translated clients to allow mobility of the clients across W-IAPs. Example The following example shows the output of show dhcp-allocation command: (Instant AP)# show dhcp-allocation ---------------------/etc/dnsmasq.conf-------------------listen-address=127.0.0.
show dhcpc-opts show dhcpc-opts Description This command displays the DHCP options configured on a W-IAP. Usage Guidelines Use this command to view the current status of the vendor-specific DHCP options configured on a W-IAP. The DHCP options are configured and enabled for assignment and distribution to DHCP clients based on the type of DHCP server, scope, and clients.
show dhcps config show dhcps config Description This command provides information about the DHCP scopes configured for a W-IAP. Usage Guidelines Use this command to view configuration details associated with the DHCP scopes enabled on a W-IAP.
Parameter Description l Centralized, L2 VLAN Indicates the VLAN ID assigned to DHCP scope. Netmask Displays the subnet mask. DNS Server Displays the DNS server IP address. Domain Name Displays the domain name configured for the DHCP scope. Default router Displays the IP address of the default router. lease-time Displays the lease-time configured for the DHCP clients. IP Address Range Displays the range of IP addresses configured for the distributed DHCP scopes.
Command History Version Description Dell Networking W-Series Instant 6.4.0.24.1 This command was modified. Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show dhcp subnets show dhcp subnets Description This command displays the subnet details and the gateway IP for distributed L2 and L3 networks. Usage Guidelines Use this command to view the subnet details for the distributed,l2 and l3 networks. Example The following example shows the output of the show dhcp subnets command: DHCP Subnet Table ----------------VLAN Type Subnet Mask Gateway Mode Rolemap ---- ---- -----------------------532 l2 192.168.132.0 255.255.255.0 0.0.0.
show distributed-dhcp-branch-counts show distributed-dhcp-branch-counts Description This command displays the branch count for the distributed DHCP scopes configured on a W-IAP. Syntax Parameter Description type Displays the branch details for the distributed DHCPs based on the type of the DHCP scope specified. The current release of Instant supports the following distributed DHCP assignment modes.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show domain-names show domain-names Description This command displays the list of enterprise-domains configured on a W-IAP. Usage Guidelines Use this command to view enterprise-domains list. The enterprise domains list displays the DNS domain names that are valid on the enterprise network. This list is used to determine how client DNS requests should be routed.
show dpi show dpi {app all|appcategory all|debug statistics|qsessions [detail []]|webcategory all|webcategory-lookup } Description This command displays the DPI configuration information. Syntax Command/Parameter Description app Displays a list of all applications (with the all keyword) and details such as application name, ID, application category, and default ports when a specific application name is provided.
---------------------------------Name App Category ID -----------------antivirus 1 authentication 2 cloud-file-storage 3 collaboration 4 encrypted 5 enterprise-apps 6 gaming 7 im-file-transfer 8 instant-messaging 9 mail-protocols 10 mobile-app-store 11 network-service 12 peer-to-peer 13 social-networking 14 standard 15 streaming 16 thin-client 17 tunneling 18 unified-communications 19 web 20 webmail 21 Total application categories = 21 The output of this command displays all application categories.
current major version current minor version :0 :1 show dpi webcategory The following example shows the output of the show dpi webcategory all command: (Instant AP)# show dpi webcategory all Pre-defined BrightCloud Web Categories -------------------------------------Name Web Category ID -----------------real-estate 1 computer-and-internet-security 2 financial-services 3 business-and-economy 4 computer-and-internet-info 5 auctions 6 shopping 7 cult-and-occult 8 travel 9 abused-drugs 10 adult-and-pornography
web-advertisements cheating gross web-based-email malware-sites phishing-and-other-frauds proxy-avoidance-and-anonymizers spyware-and-adware music government nudity news-and-media illegal content-delivery-networks internet-communications bot-nets abortion health-and-medicine spam-urls dynamically-generated-content parked-domains alcohol-and-tobacco private-ip-addresses image-and-video-search fashion-and-beauty recreation-and-hobbies motor-vehicles web-hosting category-unknown Total web categories = 80 52 5
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show dpi-stats show dpi-stats app [id |user ip |ssid ][full] appcategory [id |user ip |ssid ][full] session [full] webcategory [id |user ip |ssid ][full] webreputation [id |user ip |ssid ][full] Description This command displays the DPI statistics. Syntax Command/Parameter Description app Displays application statistics. appcategory Displays the DPI statistics for application category.
Total bytes Classication percentage :10610 :98 show dpi-stats appcategory The following example shows the output of the show dpi-stats appcategory full command: Last snapshot timestamp 17:10:47 Dpi Top Application category list --------------------------------App Category App Category Id Total bytes -------------------------- ----------web 20 10172 mobile-app-store 11 278 Not-Classified 0 160 --------------------------Total bytes :10610 Classication percentage :98 show dpi-stats session The following exa
Num of Entries:47 show dpi-stats webcategory The following example shows the output of the show dpi-stats webcategory full command: Last snapshot timestamp 17:25:43 Dpi Top Web Category list ------------------------Web Category Web Category Id -------------------------computer-and-internet-info 5 --------------------------Total bytes :740 Total bytes ----------740 show dpi-stats webreputation The following example shows the output of the show dpi-stats webreputation full command: Last snapshot timestamp
show election show election {statistics} Description This command shows master W-IAP election statistics. Syntax Parameter Description statistics Shows master election statistics. Usage Guidelines Use this command to view the statistics of the W-IAP selected as Virtual Controller.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show external-captive-portal show external-captive-portal [] Description This command displays the external captive portal configuration details. Syntax Parameter Description name Filters the output based on an existing external captive portal profile. Usage Guidelines Use this command to view information about the external captive portal server configuration details.
show fault show fault [history] Description This command displays the list of active faults that occur in the event of a system fault and the faults that were cleared from the system. Syntax Parameter Description history Displays the list of faults that were cleared. Usage Guidelines Use this command to view the active faults for a W-IAP. Active faults are generated due to system faults.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ids show ids {ap | aps| client |clients| phy-types| rap-types} Description This command displays the list of unknown APs and clients detected by the W-IAP with the IDS feature enabled. Syntax Parameter Description ap Displays the signal details for the W-IAP. aps Displays the unknown Access Points detected by the W-IAP. client Displays the details of the W-IAP to which the client is connected. clients Displays the list of unknown clients detected by the W-IAP.
The following output is displayed for the show ids clients command: Unknown Clients Detected -----------------------MAC Address Network Classification Chan.
show ids-detection config show ids-detection config Description This command displays the list of intrusion detection policies configured on a W-IAP. Usage Guidelines Use this command to view a list of intrusion detection policies enabled for a W-IAP.
signature-asleap disable disable disable enable The output for this command provides the following information: Parameter Description Infrastructure detection level Indicates if the detection level for the policies is set to off, low, medium, or high. Policies Displays the list of intrusion detection policies. Status Indicates if a policy is enabled or disabled. Low Indicates if the detection level for a policy is set to low. Medium Indicates if the detection level for a policy is set to medium.
show ids-protection config show ids-protection config Description This command displays the list of infrastructure protection policies for a W-IAP. Usage Guidelines Use this command to view the status of infrastructure protection policies on a W-IAP.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show image show image version Description This command displays the Instant software version running on a W-IAP. Example The following example shows the output of show image version command: Primary Partition Build Time :2013-03-31 11:47:06 PDT Primary Partition Build Version :6.2.1.0-3.3.0.0_37845 AP Images Classes ----------------Class ----Cassiopeia Parameter Description Primary Partition Build Time Shows the W-IAP image build time. Primary Partition Build Version Shows the W-IAP build version.
show interface counters show interface counters Description This command shows the Ethernet interface packet counters for the W-IAP. Usage Guidelines Use this command to view table of L2 interface counters.
Parameter Description Transmitted packets Shows total number of transmitted packets. Transmitted bytes Shows total number of transmitted bytes. Transmitted dropped Shows total number of packets dropped. Transmission errors Shows total number of errors during packet transmit. Lost carrier Shows total number of lost carriers. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.4 This command is introduced.
show inbound-firewall-rules show inbound-firewall-rules Description This command displays the details of inbound firewall rules configured on a W-IAP. Usage Guidelines Use this command to view the details of the inbound firewall rules configured for a W-IAP network. Example The following output is displayed for the show inbound-firewall-rules command: Access Rules -----------Src IP Src Mask Action Log TOS ------ ------------- --- --any any permit any any permit Dest IP 802.
show ip dhcp database show ip dhcp database Description This command displays the DHCP server settings. Usage Guidelines Use this command to the DHCP server settings. The DHCP server is a built-in server, used for networks in which clients are assigned IP address by the Virtual Controller. Example The following output is displayed for the show ip dhcp database command: DHCP DHCP DHCP DHCP DHCP Subnet Netmask Domain Name DNS Server DNS Cache :192.0.2.0 :255.255.255.0 :example.com :192.0.2.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ip igmp show ip igmp group [maddr ] Description This command displays information about the Internet Group Management Protocol (IGMP) group table. Syntax Parameter Description maddr Filters group table information based on the multicast IP address. Usage Guidelines Use this command to view the IGMP group table information for a W-IAP.
Parameter Description MAC Indicates the MAC address of member associated with the specified multicast group address. VLAN Indicates the VLAN ID associated with the multicast groups or a specific multicast group address. Destination Indicates the destination to which the multicast packets are routed. Age Indicates the aging time of the forwarding table entries. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced.
show ip interface brief show ip interface brief Description This command displays a summary of IP related information for all interfaces configured on a W-IAP. Usage Guidelines Use this command to view a brief summary of IP related information for the W-IAP interfaces. Example The following output is displayed for the show ip interface brief command: Interface IP Address / IP Netmask Admin Protocol br0 10.17.88.188 / 255.255.255.
show ip route show ip route Description This command displays the W-IAP routing table. Usage Guidelines Use this command to view the IP routes configured for a W-IAP. Examples The following output shows the ip address of routers and the VLANs to which they are connected. Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 172.16.10.1 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 10.17.88.128 0.0.0.0 255.255.255.192 U 0 0 0 br0 2.2.2.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.10.0 0.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show lacp status show lacp status Description This command displays the Link Aggregation Control Protocol (LACP) configuration status on a W-IAP. Usage Guidelines Use this command to view the LACP status on W-IAP220 Series devices. LACP provides a standardized means for exchanging information with partner systems to form a dynamic link aggregation group.
show l2tpv3 config show l2tpv3 config Description This command displays the L2TPV3 session and tunnel configuration details. Usage Guidelines Use this command to view the tunnel and session configuration details.
Parameter Description Failover Retry Count Displays the number of failover attempts. Retry Interval Displays the interval between each failover. Checksum Displays the end-to-end checksum of packets that pass through the tunnel. Session Name Displays the session profile name. Tunnel Name Displays the tunnel profile name. Local tunnel IP Displays the IP address of the remote end tunnel. Tunnel Mask Displays the network mask of the tunnel.
show l2tpv3 global show l2tpv3 global parameter Description This command displays L2TPv3 global configuration details such as hostname. Usage Guidelines Use this command to view the hostname configured. Example The following example shows the output of the show l2tpv3 global parameter command: L2TPV3 Global configuration --------------------------Host Name ---------Instant-C4:42:98 The output of this command includes the following information: Parameter Description Host Name Displays the W-IAP name.
show l2tpv3 session show l2tpv3 session status Description This command displays the L2TP session connectivity status. Usage Guidelines Use this command to view the session connectivity status.
show l2tpv3 system show l2tpv3 system statistics Description This command displays the L2TPV3 system statistics details. Usage Guidelines Use this command to view the tunnel and session statistics.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show l2tpv3 tunnel show l2tpv3 tunnel {config | status} Description This command displays the L2TP tunnel status and configuration details. Usage Guidelines Use this command to view the tunnel connectivity status and configuration details. Example The following example shows the output of the show l2tpv3 tunnel config command: Tunnel profile test_tunnel_primary l2tp host name: aruba1600pop658509.hsb-dev4.aus local UDP port: 1701 peer IP address: 10.13.11.
session profile: default hello timeout: 150, retry timeout: 80, idle timeout: 0 rx window size: 10, tx window size: 10, max retries: 5 use udp checksums: OFF do pmtu discovery: OFF, mtu: 1460 trace flags: PROTOCOL FSM API AVPDATA FUNC XPRT DATA SYSTEM CLI peer vendor name: Katalix Systems Ltd. Linux-2.6.32-358.2.1.el6.x86_64 (x86_64) peer protocol version: 1.
show l3-mobility show l3-mobility {config| datapath| events [ ]| status} Description This command displays details about the Layer-3 (L3) events, mobility configuration, and roaming status of the W-IAP clients. Syntax Parameter Description config Displays the L3 mobility configuration details for a W-IAP. datapath Displays the datapath statistics associated with L3 mobility.
Column Description Virtual Controller IP Displays the Virtual Controller IP address. The Virtual Controller IP configuration for each W-IAP allows the clients to roam seamlessly among all the W-IAPs. Subnet Indicates the IP address for the mobility domain. Netmask Displays the subnet mask configuration details. VLAN Displays the VLAN ID configured for the mobility domain. Virtual Controller Displays the Virtual Controller configuration associated with the mobility domain.
Parameter Description l Rx Packets - Displays information about packets received. l Tx Packets - Displays information about packets transmitted. l Rx Mcasts - Displays information about multicast packets received. l Tx Mcasts - Displays information about multicast packets transmitted.
Parameter Description Peer IP Displays the peer IP address, if any peer clients are configured. Home Vlan Displays the VLAN ID associated with the home subnet. VAP Vlan Displays the VLAN ID associated with the Virtual AP. Tunnel ID Indicates the tunnel interface used for routing packets. Old AP IP Indicates the IP address of the W-IAP from which the client has roamed. FAP IP Indicates the IP address of the W-IAP in the foreign subnet.
Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show ldap-servers show radius-servers Description This command displays the Lightweight Directory Access Protocol (LDAP) servers configured for user authentication on the Virtual Controller. Usage Guidelines Use this command to view the LDAP server configuration information available on a W-IAP.
Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log ap-debug show log ap-debug Description This command shows the W-IAP debug logs. Syntax Parameter Description Starts displaying the log output from the specified number of lines of the log. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log apifmgr show log apifmgr Description This command shows the log information for W-IAP interface manager. Syntax Parameter Description count Starts displaying the log output from the specified number of lines from the end of the log. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced.
show log convert show log convert Description This command shows image conversion details for the W-IAP. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log debug show log debug{count} Description This command shows the W-IAP full log. Syntax Parameter Description Starts displaying the log output from the specified number of lines from the end of the log. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log driver show log driver Description This command displays the status of drivers configured on the W-IAP. Command History Version Description Dell Networking WSeries Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log kernel show log kernel Description This command shows AP’s kernel logs. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log l3-mobility show log l3-mobility [] Description This command displays the logs for Layer-3 mobility domains configured on a W-IAP. Syntax Parameter Description Filters the log output based on the number specified. Usage Guidelines Use this command to view the L3-mobility logs for a W-IAP.
Content Description VC IP Indicates the IP address of the Virtual Controller. Additional Info Displays additional information if any. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log network show log network Description This command shows network logs for the W-IAP. Syntax Parameter Description Starts displaying the log output from the specified number of lines from the end of the log. Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log pppd show log pppd Description Shows the Point-to-Point Protocol daemon (PPPd) network connection details. Syntax Parameter Description PPPd network count. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log rapper show log rapper Description This command show details the VPN connection logs in detail. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log sapd show log sapd Description This command shows the SAPd details. Syntax Parameter Description Starts displaying the log output from the specified number of lines from the end of the log. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log security show log security Description This command shows security logs of the W-IAP. Syntax Parameter Description Starts displaying the log output from the specified number of lines from the end of the log. Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log system show log system Description This command shows system logs of W-IAP. Syntax Parameter Description Starts displaying the log output from the specified number of lines from the end of the log. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log upgrade show log upgrade Description This command shows image download from URL and upgrade details for both local image file and URL for the W-IAP. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log user show log user [count] Description This command shows the W-IAP user logs. Syntax Parameter Description count Starts displaying the log output from the specified number of lines from the end of the log. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show log user-debug show log user-debug [count] Description This command shows the W-IAP user debug logs. Syntax Parameter Description count Starts displaying the log output from the specified number of lines from the end of the log. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.
show log vpn-tunnel show log vpn-tunnel [count] Description This command shows VPN tunnel status for the W-IAP. Syntax Parameter Description count Starts displaying the log output from the specified number of lines from the end of the log. Usage Guidelines Use this command without the optional parameter to view a complete table of VPN tunnel status. Include the parameter to display status for the specified count of VPN tunnels.
show log wireless show log wireless [] Description This command shows wireless logs of the W-IAP. Syntax Parameter Description Starts displaying the log output from the specified number of lines from the end of the log. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.
show memory show memory Description Displays the information about memory utilization for a W-IAP. Usage Guidelines Use this command to view information about memory utilization on a W-IAP.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show mgmt-user show mgmt-user Description This command displays the credentials for the admin users for the W-IAP management interface. Usage Guidelines Use this command to view the admin user credentials required for accessing the W-IAP and external server configuration details for the management users.
Column Description NAS is configured. In Use Indicates if the server is in use. RFC3576 Indicates if the W-IAPs are configured to process RFC 3576-compliant Change of Authorization (CoA). NAS IP address Displays the IP address of the Network Access Server (NAS) if NAS is configured. Name (Management User Table) Indicates the username of the admin user Password Indicates the password of the admin user. Type Indicates if the type of the user (admin, read-only, or guest management user).
show network show network Description This command shows network configuration details for a W-IAP. Syntax Parameter Description Displays the name of a network profile. Usage Guidelines Use this command without the optional parameter to view a complete configuration details of a network profile on the W-IAP. Include the parameter to display settings for a single network SSID only.
Work without usable uplink :Disabled Percentage of Airtime: :Unlimited Overall Limit: :Unlimited Per-user Limit: :Unlimited Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show network-summary show network-summary Description This command displays the status of the available network configurations on the W-IAP. Usage Guidelines Use this command to view the status of the network configurations.
show opendns show opendns [support] Description This command displays the open DNS configuration details for a W-IAP. Syntax Parameter Description support Displays if the OpenDNS credentials if the OpenDNS service is configured on the W-IAP. Usage Guidelines Use this command to view open DNS configuration details. The OpenDNS credentials are used by Instant to access OpenDNS to provide enterprise-level content filtering.
show port status show port status Description Displays the activity statistics on each of the port on the controller. Example The following example shows the output of the show port status command: (Instant AP)# show port status Port Type Admin-State Oper-State ---- ---- ----------- ---------bond0 GE down up Parameter Description Port Displays the port number on the controller. Type Displays the port type. Admin-State Displays if the port is enabled or disabled.
show pppoe show pppoe {config|debug logs|debug status} Description This command shows PPPoE debug logs and uplink status. Syntax Parameter Description config Displays PPPoE configuration details. debug logs Displays PPPoE debug logs. debug status Displays the uplink status. Example show pppoe config The following example shows the configuration of the PPPoE show pppoe config command.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show process show process Description This command displays a list of processes running on a W-IAP. Usage Guidelines Use this command to view the processes running on the W-IAP for debugging purpose.
show proxy config show proxy config Description This command displays the HTTP proxy configuration settings on a W-IAP. Example The following example shows the output of show proxy config command: Proxy server :192.0.2.1 Proxy port :8080 Exceptions ---------No Exception -- --------1 192.0.2.2 The output of this command provides the following information: Parameter Description Proxy server Displays the IP address of the HTTP proxy. Proxy port Displays the port number configured for the HTTP proxy.
show radio config show radio config Description This command displays the 2.4 GHz and 5 GHz radio configuration details for a W-IAP. Usage Guidelines Use this command to view the 2.4 GHz and 5 GHz radio configuration details for a W-IAP. Example The following example shows the output of show radio config command: (Instant AP)# show radio config Legacy Mode:enable Beacon Interval:100 802.11d/802.
Parameter Description Channel Switch Announcement Count Displays the number of channel switching announcements that are sent before switching to a new channel. MAX distance Indicates the maximum distance in meters between a client and an AP or between a mesh point and a mesh portal. Channel Reuse Type Indicates if channel reuse type is enabled. Channel Reuse Threshold Displays the channel reuse threshold configured for channel reuse type.
show radius-servers support show radius-servers support Description This command displays the RADIUS server configuration details for a W-IAP. Usage Guidelines Use this command to view the RADIUS server information for a W-IAP. Example The following example shows the output of show radius-servers support command: RADIUS Servers -------------Name IP Address Port Acctport Key ---- ---------- ---- -------- ---Server1 192.0.2.
Parameter Description Airgroup RFC3576 port Indicates the port number used for sending AirGroup CoA. Deadtime Indicates the RADIUS server dead-time. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show rft trans-id show rft trans-id {| all} Description This command shows the transaction IDs of tests performed for RF troubleshooting. Syntax Parameter Description Indicates the transaction ID for which you want to view the output. all Displays all the transaction IDs associated with the RF tests. Usage guidelines Use the show rft trans-id command to view the transaction IDs for the most recent test performed for RF troubleshooting.
show rft profile show rft profile {all|antenna-connectivity|ht-link-quality|link-quality|raw} Description This command shows the RF test profile for testing RF parameters such as antenna connectivity, link quality, and channel link quality. Syntax Parameter Description all Displays the parameters for all test profiles. antenna-connectivity Displays the parameters details for the antenna-connectivity test profile. ht-link-quality Displays the parameter details for the HT link quality test profile.
Num Retries 0 Data Rate All rates are tried Profile AntennaConnectivity: Built-in profile ---------------------------------------------Parameter Value --------- ----Frame Type Null Data Num Packets 100 Packet Size 1500 Num Retries 0 Radio 0 (1 for AP-80-S only) Command History Version Description Dell Networking W-Series Instant 6.4.0.2-4.1 This command is introduced.
show running-config show running-config Description This command displays the current configuration running on a W-IAP, including the current changes that are yet to be saved. Usage Guidelines Use this command to view the current configuration information stored in the W-IAP flash memory. Example The following example shows the partial output of the show running-config command output: version 6.4.0.0-4.1.
max-authentication-failures 0 rf-band all captive-portal disable dtim-period 1 inactivity-timeout 1000 broadcast-filter none dmo-channel-utilization-threshold 90 local-probe-req-thresh 0 max-clients-threshold 64 dot11k dot11v auth-survivability cache-time-out 24 wlan external-captive-portal server localhost port 80 url "/" auth-text "Authenticated" auto-whitelist-disable https blacklist-time 3600 auth-failure-blacklist-time 3600 ids wireless-containment none wired-port-profile wired-instant switchport-mode
Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show snmp-configuration show snmp-configuration Description This command displays the Simple Network Management Protocol (SNMP) configuration details for a Virtual Controller. Usage Guidelines Use this command to view the SNMP information configured on a Virtual Controller.
Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show snmp trap-queue show snmp trap-queue Description This command displays the list of SNMP traps in queue. Usage Guidelines Use this command to view the SNMP traps in queue. Example The following example shows the partial output of show snmp trap-queue command: 2013-05-12 14:05:27 An AP (NAME d8:c7:c8:cb:d4:20 and MAC d8:c7:c8:cb:d4:20 on RADIO 2) detected an interfering access point (BSSID 00:24:6c:80:7d:11 and SSID NTT-SPOT on CHANNEL 1).
show spectrum-alert show spectrum-alert Description This command displays the list of spectrum alerts for a W-IAP. Syntax Parameter Description Filters the alerts based on the specified number. Usage Guidelines Use this command to view the spectrum alerts for a W-IAP. When a new non Wi-Fi device is found, an alert is reported to the Virtual Controller.
show stats show stats {ap | client | global | network } [count] Description This command displays the aggregate statistics for W-IAPs, W-IAP clients, W-IAP cluster, and network profiles configured on a W-IAP. Syntax Parameter Description ap Displays information on W-IAP utilization, RF trends, and client details for a specific W-IAP.
--------- ------------------- ---------------- ----------------------- ---------------------------- ----------------------- --------------------------- --------------------------------- ------ ---------------------- --------------------00:34:46 8 164 4 239 0 1 8 1 93 99 00:34:17 8 164 4 239 0 1 8 1 186 199 0 1 9 RF Trends --------Timestamp Utilization [2.4 GHz] (%) Utilization [5.0 GHz] (%) Noise Floor [2.4 GHz] (dBm) Noise Floor [5.0 GHz] (dBm) 2.4 GHz Frames [Errors] (fps) 5.0 GHz Frames [Errors] (fps) 2.
Client Signal Speed IP Address ------ ------ ----- ---------169.254.90.154 good good 169.254.90.154 Access Point Heatmap -------------------Access Point Utilization Noise Errors ------------ ----------- ----- -----d8:c7:c8:cb:d4:20 good good good Client List ----------Name IP Address MAC Address OS Network Access Point Channel Type Role ---- ---------- ----------- -- ------- ------------ ------- ---- ---169.254.90.
16:36:54 0 0 0 0 0 16:36:24 0 0 0 0 0 16:35:54 0 0 0 0 0 16:35:23 0 0 0 0 0 16:34:53 0 0 0 0 0 16:34:23 0 0 0 0 0 Access Point Heatmap -------------------Access Points Utilization Noise Errors ------------- ----------- ----- -----d8:c7:c8:c4:42:98 poor good good Client Heatmap -------------Clients Signal Speed IP Address ------- ------ ----- ---------Name :test123 ESSID :test123 Status :Enabled Mode :wpa2-aes Band :all Type :employee Termination :Disabled Passphrase : WEP Key : WEP Key Index :1 VLAN : Serve
Max Clients Threshold :64 Background WMM Share :0 Best Effort WMM Share :0 Video WMM Share :0 Voice WMM Share :0 Certificate Installed: :No Internal Radius Users: :0 Internal Guest Users: :0 Role Derivation Rules --------------------Attribue Operation Operand Role Name Index -------- --------- ------- --------- ----Vlan Derivation Rules --------------------Attribue Operation Operand Vlan Id -------- --------- ------- ------RADIUS Servers -------------Name IP Address Port Key Timeout Retry Count NAS IP Addre
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show subscription-aps show subscription-aps Description This command displays the subscription status of a W-IAP. Example (Instant AP) (config) # show subscription-aps IAP controlled by Cloud-Server:disable subscription enabled by manually :disable Subscription Ap List -------------------MAC Address Status ----------- -----d8:c7:c8:c4:56:de ACTIVE d8:c7:c8:c4:57:06 ACTIVE Command History Version Description Dell Networking WSeries Instant 6.2.1.0-3.3 This command is introduced.
show summary show summary { | support} Description This command shows the current configuration details. Syntax Parameter Description Shows the difference in configuration. support Shows the summary support containing the configuration details used by support. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.4 This command was modified. Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced.
show swarm show swarm {state|mode} Description This command displays the current status of the W-IAP cluster and indicates if W-IAPs are in a cluster or standalone mode. Usage Guidelines Use this command to view the current status of the W-IAP cluster and to view information about the functioning mode of the W-IAP cluster.
show supported-cert-formats show supported-cert-formats Description This command displays the supported server and CA certificate formats. Usage Guidelines Use this command to view the list certificate formats supported by the W-IAP. Examples Server Certificate Formats -------------------------Name ---PEM CA Certificate Formats ---------------------Name ---PEM DER Command History Version Description Dell Networking W-Series The output of this command is modified. Instant 6.3.1.1-4.
show syslog-level show syslog-level Description This command displays the Syslog logging levels configured for a W-IAP. Usage Guidelines Use this command to view the Syslog logging facilities and the associated logging level.
Parameter Description for all Syslog facilities. l Informational—Messages of general interest to system users. l Debug—Messages containing information useful for debugging. Command History Version Description Dell Networking WSeries Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show tacacs-servers show tacacs-servers Description This command displays all the tacacs servers configured on a W-IAP. Usage Guidelines Use this command to view the list of tacacs servers available on a W-IAP. Example The following example shows the output of the show tacacs-servers command: TACACS Servers -------------Name IP Address Port Key Timeout Retry Count In Use ---- ---------- ---- --- ------- ----- ----- -----tacacs1 10.64.16.240 49 pass123 20 1 Yes tacacs2 192.168.0.
show tech-support show tech-support Description This command displays the complete W-IAP information and the associated configuration details, which can be used by the technical support representatives for debugging. Usage Guidelines Use this command to view and analyze W-IAP configuration details for debugging any AP related issues. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced.
show uncommitted-config show uncommitted-config Description This command displays the current configuration details that are yet to be committed and saved on the W-IAP. Usage Guidelines Use this command to view the uncommitted configuration details. Use the commit apply command to commit the configuration changes. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced.
show upgrade info show upgrade info Description This command displays the image upgrade details for a W-IAP. Usage Guidelines Use this command to view the image upgrade details for a W-IAP. Example The following example shows the output of show upgrade info command: Image Upgrade Progress ---------------------Mac IP Address AP Class Status Image Info Error Detail --- ---------- -------- ------ ---------- -----------d8:c7:c8:cb:d4:20 10.17.88.
Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show uplink show uplink {config|stats} Description This command displays uplink configuration details and status of for a W-IAP. Syntax Parameter Description show uplink config Displays the uplink interface configuration details for a W-IAP. show uplink stats Displays the aggregate uplink statistics for a W-IAP Usage Guidelines Use this command to view the information about uplink status and configuration for a W-IAP.
eth0 UP 0 Yes Wifi-sta INIT 6 No 3G/4G INIT 7 No Internet failover :disable Max allowed test packet loss:10 Secs between test packets :30 VPN failover timeout (secs) :180 ICMP pkt sent :0 ICMP pkt lost :0 Continuous pkt lost :0 VPN down time :0 The output of this command provides the following information: Column Description Uplink preemption Indicates if the uplink preemption is enabled. Uplink enforce Indicates if any uplinks are enforced.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show uplink-vlan show uplink-vlan Description This command displays the uplink VLAN configuration details for the management traffic. Usage Guidelines Use this command to view the uplink VLAN configuration details for management traffic. The uplink management VLAN configuration allows you to tag management traffic and connect multiple W-IAP clusters (Virtual Controllers) to the same port on an upstream switch (for example, W-AirWave server).
show users show user [portal| Radius] Description This command displays users configured for a W-IAP. Syntax Parameter Description portal Displays the W-IAP user credentials. radius Displays the user credentials for the RADIUS server authentication Usage Guidelines Use this command to view the W-IAP user credentials.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show valid-channels show valid-channels Description This command displays the list of channels that are valid for a W-IAP serving a specific regulatory domain. Usage Guidelines Use this command to view the list of valid channels that can be configured on your W-IAP. Example The following example shows the output of show valid-channels command: 2.4 GHz 1 2 3 4 5 6 7 8 9 10 11 12 13 1+ 2+ 3+ 4+ 5+ 6+ 7+ 5.
Parameter Description 2.4 GHz Displays the list of channels valid for a W-IAP in the 2.4 GHz band. 5.0 GHz Displays the list of channels valid for a W-IAP in the 5.0 GHz band. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
show version show version Description This command displays the Instant software version running on a W-IAP. Example The following example shows the output of the show version command: Aruba Operating System Software. ArubaOS (MODEL: W-AP105), Version 6.3.1.1-4.0.0.0 website: http://www.dell.com Copyright (c) 2002-2013, Aruba Networks, Inc.
show vpn show vpn {config|status|tunnels} Description This command displays the status and configuration details for VPN-enabled W-IAPs. Syntax Parameter Description config Displays configuration details for the VPN-enabled W-IAPs. status Displays the status of the VPN connections enabled on a W-IAP. tunnels Displays the IAP-VPN retry counter statistics.
l vpn monitor-pkt-lost-cnt l vpn monitor-pkt-send-freq l vpn ikepsk l gre type l gre primary l gre per-ap-tunnel The following example shows the output displayed for show vpn status command: profile name:default -------------------------------------------------current using tunnel :unselected tunnel ipsec is preempt status :disable ipsec is fast failover status :disable ipsec hold on period :600 ipsec tunnel monitor frequency (seconds/packet) :5 ipsec tunnel monitor timeout by lost packet cnt :2
show walled-garden show walled-garden Description This command displays the domain names and websites that are blacklisted or whitelisted by a W-IAP. Usage Guidelines Use this command to view the walled garden configuration details for a W-IAP. A walled garden typically controls access to web content and services. The Walled garden access is required when an external captive portal is used.
show wifi-uplink show wifi-uplink {auth log |config | status} Description This command displays the configuration details, the status, and authentication log for the Wi-Fi uplinks configured on a W-IAP. Syntax Parameter Description auth log Displays the authentication configuration details and an authentication log. config Displays the Wi-Fi configuration parameters enabled on a W-IAP. status Displays the status of the Wi-Fi uplink.
Parameter Description uplink-band Displays the band configured for the Wi-Fi uplink connection. For example, dot11a and dot11g. show wifi-uplink status The following output is displayed for the show wifi-uplink status command: configured :YES enabled :YES The output of this command indicates if the Wi-Fi uplink is configured and enabled on the W-IAP. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced.
show wired-port show wired-port Description This command displays the configuration details associated with a wired profile configured on a W-IAP. Syntax Parameter Description Displays the current configuration details for a specific wired profile. Usage Guidelines Use this command to view the details of a wired profile configured on a W-IAP.
Access Rules -----------Dest IP Dest Mask Dest Match Protocol (id:sport:eport) Action Log TOS 802.
show wired-port-settings show wired-port-settings Description This command displays the list of wired profiles configured on a W-IAP. Usage Guidelines Use this command to view the wired profiles configured on a W-IAP.
Column Description duplex Indicates if the client traffic duplexing full, half, or automatically assigned based on the capabilities of the client, the AP, and the cable. poe Indicates if Power over Ethernet (PoE) is enabled. In Use Indicates if the wired profile is in use. Authentication Method Indicates the authentication method configured for the wired profile. Port Indicates the port number to which a wired profile is assigned.
show wispr config show wispr config Description This command displays the Wireless Internet Service Provider roaming (WISPr) authentication parameters configured on a W-IAP. Usage Guidelines Use this command to view the WISPr configuration details for a W-IAP. Example The following example shows the output of show wispr config command: WISPr WISPr WISPr WISPr WISPr WISPr ISO Country Code :91 E.164 Country Code :IN E.
show xml-api-server show xml-api-server config Description This command displays the XML API server configuration details. Usage Guidelines Use this command to view the XML API server configuration details. Example The following example shows the output of the show xml-api-server command: ip :192.0.2.5 key :user1234 Command History Version Description Dell Networking W-Series Instant 6.4.0.2-4.1 This command is introduced.
snmp-server snmp-server community host version {1 udp-port }|{2c|3 [inform] [udp-port ]} user [ Description This command configures SNMP parameters. Syntax Parameter Description Range Default community Sets the read-only community string. — — engine-id Sets the SNMP server engine ID as a hexadecimal number.
Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Configuration mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
subscription-ap subscription-ap status no… Description This command configures the subscription status for a W-IAP. Syntax Command/Parameter Description Enter the MAC address of the W-IAP. Enter the subscription status for the W-IAP. no… Removes the configuration. Usage Guidelines Use this command to subscribe the W-IAP based on its MAC address.
subscription-ap-enable subscription-ap-enable no… Description This command enables the subscription of a W-IAP. Syntax Command/Parameter Description subscription-ap-enable Enables the subscription for a W-IAP. no Removes the configuration. Usage Guidelines Use this command to enable the subscription of the W-IAP. Example (Instant AP)(config) # subscription-ap-enable Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced.
syslocation syslocation no… Description This command allows you to define the physical location for the W-IAP. Syntax Command/Parameter Description Allows you to specify a physical location. no Removes the configuration. Usage Guidelines Use this command to define the physical location of the W-IAP.
syslog-level syslog-level {ap-debug|network|security|system|user|user-debug|wireless} no... Description This command configures syslog facility levels. Syslog Facility is an information field associated with a syslog message. Syntax Parameter Description Range Default syslog-level Configures the Syslog facility level.
Parameter Description Range Default wireless Generates a log about radio configuration. — — no… Removes the configuration. — — Usage Guidelines Use this command to configure syslog facility levels and to generate logs based on various user and W-IAP parameters.
syslog-server syslog-server no… Description This command configures Syslog server for a W-IAP. Syntax Parameter Description Range Default syslog-server Specifies the IP address to configure the syslog server. — — no… Removes the configuration. — — Usage Guidelines Use this command to configure syslog server for a W-IAP. Example The following command configures the IP address of the syslog server for a W-IAP. (Instant AP)(config)# syslog-server 192.0.2.
telnet-server telnet-server no… Description This command enables Telnet access to Instant command line interface (CLI). Syntax Command/Parameter Description telnet-server Enables Telnet access to the Instant CLI. no… Removes the configuration Usage Guidelines Use this command to enable Telnet access to the Instant CLI.
terminal-access terminal-access no… Description This command enables Secure Shell (SSH) access to Instant CLI. Syntax Command/Parameter Description terminal-access Enables terminal access to the Instant CLI. no… Removes the configuration. Usage Guidelines Use this command to enable SSH access to the Instant CLI.
tftp-dump-server tftp-dump-server no… Description This command configures TFTP dump server for a W-IAP. Syntax Parameter Description tftp-dump-server Configures TFTP dump server IP address. no… Removes the configuration Usage Guidelines Use this command to configure TFTP dump server for storing core dump files.
traceroute traceroute Description This command traces the route to the specified IP address. Syntax Parameter Description Displays the destination IP address. Usage Guidelines Use this command to identify points of failure in your network. Example The following example shows the output of traceroute command: #traceroute 10.1.2.3 Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced.
upgrade-image upgrade-image upgrade-image2 upgrade-image2-no-reboot Description These commands allow you to upgrade a W-IAP to use a new image file. Syntax Parameter Description upgrade-image Upgrades the W-IAP to use a new image. upgrade-image2 Uploads an additional image file and upgrades the W-IAP to use this image file when required. upgrade-image2-no-reboot Uploads an additional image file and upgrades the W-IAP to use the new image without rebooting the W-IAPs.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
uplink uplink enforce {ethernet| cellular |wifi | none} failover-internet failover-internet-check-timeout failover-internet-pkt-lost-cnt failover-internet-pkt-send-freq failover-vpn-timeout preemption uplink-priority {cellular | ethernet | [port ]|wifi } no… Description This command configures uplink connections. Syntax Parameter Description Range Default uplink Enables the uplink configuration sub-mode.
Parameter Description Range Default failover-internet-pkt-lost-cnt Configures the number of packets that are to be lost when verifying the uplink availability using the Internet. 1—1000 10 failover-internet-pkt-send-freq Configures the frequency in seconds, at which the ICMP packets are sent to verify the uplink availability using the Internet. 1—3600 30 failover-vpn-timeout Configures a duration to wait for an uplink switch based on VPN status.
Uplink Priority When uplink priority is configured, the W-IAP tries to get a higher priority link every ten minutes even if the current uplink is up. This does not affect the current uplink connection. If the higher uplink is usable, the W-IAP switches over to that uplink. Preemption is enabled by default. Uplink Switchover The default priority for uplink switchover is Ethernet and then 3G/4G. The W-IAP has the ability to switch to the lower priority uplink if the current uplink is down.
uplink-vlan uplink-vlan Description This command configures uplink VLAN for management traffic on a W-IAP. Syntax Parameter Description Range Default Assigns a VLAN ID for the uplink management traffic 0-4093 0 Usage Guidelines Use this command to configure the uplink VLAN configuration details for management traffic.
user user [] [portal| radius] no… Description This command creates users for a W-IAP. Syntax Parameter Description user Creates a username for the W-IAP user. Assigns a password for the W-IAP user portal Configures a guest user. radius Configures an employee user no… Removes the configuration Usage Guidelines The Instant user database consists of a list of guest and employee users. Addition of a user involves specifying a login credentials for a user.
Command Information W-IAP Platform Command Mode All platforms Configuration mode 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
version version Description This command configures a version number for the W-IAP. Syntax Parameter Description version Assigns a version number for the W-IAP. Usage Guidelines Use this command to configure a version number for the W-IAP. Example The following example configures a version number for the W-IAP. Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced.
virtual-controller-country virtual-controller-country no… Description This command configures the location of the W-IAP. Syntax Parameter Description virtual-controller-country Specifies the country of operation for a W-IAP. no… Removes the configuration. Usage Guidelines Use this command to configure the country code for W-IAPs.
virtual-controller-ip virtual-controller-ip Description This command configures an IP address for the Virtual Controller. Syntax Parameter Description virtual-controller-ip Assigns an IP address for the Virtual Controller. Usage Guidelines Use this command to configure an IP address for the Virtual Controller. Example The following example assigns an IP address for the Virtual Controller: (Instant AP)(config)# virtual-controller-ip 192.0.2.
virtual-controller-key virtual-controller-key Description This command configures a unique name for the Virtual Controller. Syntax Parameter Description virtual-controller-key Defines a unique name for the Virtual Controller. Usage Guidelines Use this command to assign a name for the Virtual Controller.
virtual-controller-vlan virtual-controller-vlan no… Description This command configures a VLAN for the Virtual Controller. Syntax Parameter Description virtual-controller-vlan Associates a VLAN ID with the Virtual Controller. Configures a subnet mask for the Virtual Controller. Configures a gateway for the Virtual Controller.
vpn backup vpn backup no… Description This command configures a secondary or backup VPN server for VPN connections. Syntax Parameter Description vpn backup Configures a fully qualified domain name for the secondary VPN or IPSec endpoint. no… Removes the configuration. Usage Guidelines Use this command to configure a backup VPN server.
vpn fast-failover vpn fast-failover no… Description This command configures fast failover feature for VPN connections. Syntax Parameter Description vpn fast-failover Enables fast failover feature for VPN connections. no… Removes the configuration. Usage Guidelines Use this command to configure fast failover feature for VPN connections.
vpn gre-outside vpn gre-outside no… Description This command enables automatic configuration of the GRE tunnel between the W-IAP and the controller. Usage Guidelines Use this command to enable automatic configuration of the GRE tunnel between the controller to provide L2 connectivity.
vpn hold-time vpn hold-time no... Description This command configures the time interval after which the W-IAP can switch over to the primary host when preemption is enabled. Syntax Parameter Description vpn hold-time Configures a time period in seconds after which the W-IAPs can switch to primary VPN server. no… Removes the configuration. Usage Guidelines Use this command to configure a period to hold on switching to the primary server when pre-emption is enabled.
vpn ikepsk vpn ikepsk username password no… Description This command configures user credentials for the VPN connection. Syntax Parameter Description vpn ikepsk Specifies an IKE authentication for VPN connection using pre-shared keys username Defines a username that enables access to VPN. password Defines a password that enables access to VPN. no… Removes the configuration.
vpn monitor-pkt-lost-cnt vpn monitor-pkt-lost-cnt no... Description This command configures the number of lost packets after which the W-IAP can determine that the VPN connection is not available. Parameter Description Range Default vpn monitor-pkt-lost-cnt Defines the number of lost packets for VPN connection test or monitoring by the W-IAP. — 2 no… Removes the configuration.
vpn monitor-pkt-send-freq vpn monitor-pkt-send-freq no... Description This command configures the frequency at which the W-IAP can verify if the active VPN connection is available. Syntax Parameter Description Range Default vpn monitor-pktsend-freq Configures a frequency interval in seconds at which the test packets are sent. — 5 no… Removes the VPN monitoring frequency configuration.
vpn preemption vpn preemption no… Description This command enables pre-emption to allow the VPN tunnel to switch back to the primary host after a failover. Syntax Parameter Description vpn preemption Enables pre-emption to allow the VPN tunnel to switch to the primary VPN server when it becomes available after a failover. no… Removes the VPN pre-emption configuration.
vpn primary vpn primary no... Description This command configures a primary Virtual Private Networks (VPN) server for VPN connections. Syntax Parameter Description Range Default vpn primary Configures a fully qualified domain name for the main VPN or IPSec endpoint. — — no… Removes the VPN server configuration. — — Usage Guidelines Use this command to configure a primary VPN server for IAP-VPN connections.
vpn reconnect-time-on-failover vpn reconnect-time-on-failover Description This command defines a period after which the VPN connection can be reestablished when the primary VPN tunnel fails. Syntax Parameter Description vpn reconnect-time-on-failover Configures a time period in minutes after which the VPN is reconnected when the primary VPN tunnel fails. Usage Guidelines Use this command to configure a time period for reestablishing VPN connections.
vpn reconnect-user-on-failover vpn reconnect-user-on-failover no… Description This command enables the users to reconnect to the VPN when the primary VPN tunnel fails. Syntax Parameter Description vpn reconnect-user-onfailover Enables users to reconnect to the VPN during a VPN failover. no… Removes the configuration. Usage Guidelines Use this command to allow the users to reconnect to the VPN after a VPN failover. When enabled , the W-IAP reconnects the user during a VPN failover.
wifi0-mode wifi0-mode Description This command configures a W-IAP to function in the access, monitor, or spectrum monitor mode. Syntax Parameter Description Range Default Configures the W-IAP to function in any of the following modes: access, monitor, spectrummonitor access l Access— In Access mode, the W-IAP serves clients, while also monitoring for rogue APs in the background.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
wifi1-mode wifi1-mode Description This command configures a W-IAP to function in the access, monitor, or spectrum monitor mode. Syntax Parameter Description Range Default Configures the W-IAP to function in any of the following modes: access, monitor, spectrummonitor access l Access— In Access mode, the W-IAP serves clients, while also monitoring for rogue APs in the background.
Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
wired-port-profile wired-port-profile access-rule-name allowed-vlan auth-server captive-portal {[exclude-uplink ]|external[exclude-uplink | profile [exclude-uplink ]]} content-filtering dot1x duplex l2-auth-failthrough mac-authentication native-vlan poe radius-reauth-interval server-load-balancing set-role {{equals|not-equal|starts-with|ends-with|contains} |value-of} set-role-mac-auth
Command/Parameter Description Range Default captive-portal{ [exclude-uplink ] |external[exclude-uplink | profile [exclude-uplink ]]} Enables internal or external captive portal authentication for the wired profile users. — — You can also disable redirection to the captive portal based on the type of current uplink. If the external captive profiles are created, you can specify the profile name by using the external and profile keywords and associated parameters.
Command/Parameter Description ends-with| contains}operator> | value-of} You can specify any of the following conditions: set-role-machine-auth l contains—The rule is applied only if the attribute value contains the specified string. l ends-with—The rule is applied only if the attribute value ends with the specified string. l equals—The rule is applied only if the attribute value is equal to the specified string.
Command/Parameter Description Range Default set-vlan {equals|not-equals| startswith| ends-with| contains} | value-of} Assigns a VLAN to the clients. The first rule that matches the configured condition is applied. — — You can specify any of the following conditions: l contains—The rule is applied only if the attribute value contains the specified string. l ends-with—The rule is applied only if the attribute value ends with the specified string.
Command/Parameter Description Range Default wired profile. You can specify any of the following modes: l Access—Use this mode to allow the port to carry a single VLAN specified as the native VLAN. l Trunk—Use this mode to allow the port to carry packets for multiple VLANs specified as allowed VLANs. type Defines the primary usage of the wired profile.
(Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant AP)(wired ap profile"guestWired1")# AP)(wired ap profile"guestWired1")# AP)(wired ap profile"guestWired1")# AP)(wired ap profile"guestWired1")# AP)(wired ap profile"guestWired1")# AP)(wired ap profile"guestWired1")# AP)(wired ap profile"guestWired1")# AP)(wired ap profile"guestWired1")# AP)(wired ap profile"guestWired1")# AP)(wired ap profile"gues
wlan access-rule wlan access-rule bandwidth-limit {downstream | upstream | peruser { downstream | upstream }} calea captive-portal {external [profile ]|internal} index rule { {permit|deny|src-nat|dst-nat { | }}| app {permit| deny}| appcategory | webcategory {permit| deny}| webreputation [
Command/Parameter Description Range Default calea Creates an access rule for CALEA integration. — — captive-portal {external [profile ] |internal} Configures a captive-portal role, to assign to the users role after a successful authentication. — — Creates an index entry for access rules. — — rule Creates an access rule. — — You can create up to 128 access control entries in an ACL for a user role.
Command/Parameter Description Range Default src-nat Allows the W-IAP to perform source NAT on packets. When configured, the source IP changes to the outgoing interface IP address (implied NAT pool) or from the pool configured (manual NAT pool). — — Specifies the destination NAT IP address for the specified packets when dst-nat action is configured. — — Specifies the destination NAT port for the specified packets when dst-nat action is configured.
Command/Parameter Description Range Default following options: l Log—Creates a log entry when this rule is triggered. l Blacklist—Blacklists the client when this rule is triggered. l Classify-media—Performs a packet inspection on all non-NAT traffic and marks the critical traffic. l Disable-scanning—Disables ARM scanning when this rule is triggered. l DSCP tag—Specifies a DSCP value to prioritize traffic when this rule is triggered. l 802.1p priority—Sets an 802.1p priority.
(Instant AP)(Access Rule "WirelessRule")# match tcp 21 21 deny (Instant AP)(Access Rule "WirelessRule")# match udp 21 21 deny (Instant AP)(Access Rule "WirelessRule")# downstream 256 throttle-up 256 (Instant AP)(Access Rule "WirelessRule")# throttle-downstream 256 throttle-up 256 (Instant AP)(Access Rule "WirelessRule")# (Instant AP)(Access Rule "WirelessRule")# permit (Instant AP)(Access Rule "WirelessRule")# deny (Instant AP)(Access Rule "WirelessRule")# (Instant AP)# commit apply rule 192.0.2.2 255.255.
wlan auth-server wlan auth-server acctport cppm-rfc3576-only cppm-rfc3576-port deadtime
Command/Parameter Description Range Default drp-ip vlan gateway Configures the IP address, net mask and VLAN, which will be used as source address and VLAN for RADIUS packets. — — NOTE: Before configuring DRP IP address, ensure that dynamic RADIUS proxy is enabled, and a static Virtual Controller IP is configured.
Command/Parameter Description Range Default — — Retry count), before the user gets disconnected. For example, if the Timeout is 5 seconds, Retry counter is 3, user is disconnected after 20 seconds. no… Removes the configuration. Usage Guidelines Use this command to configure an external RADIUS server and a CPPM server as a RADIUS server for AirGroup Change of Authorization (CoA) requests.
wlan captive-portal wlan captive-portal authenticated background-color banner-color banner-text custom-logo decoded-texts redirect-url terms-of-use use-policy no… Description This command customizes the appearance of the internal captive portal splash page of the guest users.
Command/Parameter Description Range Default NOTE: By default, after entering the requested info at the splash page, the users are redirected to the URL that was originally requested. When a URL is configured for redirection, it overrides the user’s original request and redirects them to URL configured for redirection. terms-of-use Defines the terms and conditions that the user must be aware of.
Command Information W-IAP Platform Command Mode All platforms Configuration mode and captive portal sub-mode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
wlan external-captive-portal wlan external-captive-portal [profile-name] auth-text auto-whitelist-disable https port redirect-url server server-fail-through url no… Description This command configures profiles for external captive portal. Syntax Command/Parameter Description Range Default wlan external-captiveportal [profile-name] Creates an external captive portal profile.
Command/Parameter Description Range Default portal server. server-fail-through Allows the guest clients to access the Internet when the external captive portal server is not available. — Disabled no… Removes the configuration. — — Usage Guidelines Use this command to configure external captive portal profiles for guest users.
wlan ldap-server wlan ldap-server admin-dn admin-password base-dn deadtime
Command/Parameter Description Range Default filter Configures the filter to apply when searching for a user in the LDAP database. strings (objectclass=*) key-attribute Configures the attribute to use as a key when searching for the LDAP server. — — For Active Directory, the value is sAMAccountName ip Configures the IP address of the LDAP server. — — port Configures the authorization port number of the LDAP server.
Command Information W-IAP Platform Command Mode All platforms Configuration mode and LDAP server sub-mode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
wlan ssid-profile wlan ssid-profile a-max-tx-rate a-min-tx-rate air-time-limit auth-pkt-mac-format {delimiter|upper-case} auth-server auth-survivability bandwidth-limit blacklist broadcast-filter captive-portal {[exclude-uplink ]|external[exclude-uplink | profile [exclude-uplink ]]} content-filtering deny-inter-user-bridging deny-local-routing disable dmo-channel-utilization-threshold dot11k dot11r dot11v
termination type {employee|voice|guest} vlan wep-key wispr wmm-background-dscp wmm-background-share wmm-best-effort-dscp wmm-best-effort-share wmm-video-dscp wmm-video-share wmm-voice-dscp wmm-voice-share work-without-uplink wpa-passphrase zone no… Description This command configures a WLAN SSID profile.
Command/Parameter Description Range Default authentication methods. And without the macauthentication-delimiter and mac-authentication-uppercase configuration, it works on the username and password for MAC Authentication. auth-server Configures an authentication server for the SSID users. — — auth-survivability Enables the authentication survivability feature. — — NOTE: The authentication survivability feature requires ClearPass Policy Manager 6.0.
Command/Parameter Range Default — — You can also exclude an uplink type for the captive portal based SSID profiles. When an uplink type is selected for the excludeuplink option, redirection to the captive portal based on the type of specified uplink is disabled. 3G,4G, wifi,ethernet — content-filtering Routes all DNS requests for the non-corporate domains to OpenDNS on this network.
Command/Parameter Description Range Default connect to the Internet, but cannot communicate with each other, and the routing traffic between the clients is sent to the upstream device to make the forwarding decision. disable Disables the SSID. By default all SSIDs are enabled. — — dmo-channel-utilizationthreshold Sets a threshold for DMO channel utilization. W-IAP sends multicast traffic over the wireless link. 1–100 percentage value 90 dot11k Enables 802.
Command/Parameter Description Range Default dot11v Enables 802.11v based BSS transition. — — dtim-period Configures the Delivery Traffic Indication Message (DTIM) interval for the SSID profile. 1–10 beacons 1 — Disabled The DTIM interval determines how often the W-IAP should deliver the buffered broadcast and multicast frames to associated clients in the powersaving mode. When configured, the client checks for buffered data on the W-IAP at the specified number of beacons.
Command/Parameter Description Range Default g-min-tx-rate Configures the specify the minimum transmission rate for the 2.4 GHz band. 1-54 Mbps 1 Mbps g-max-tx-rate Configures the specify the maximum transmission rate for the 2.4 GHz band. 1-54 Mbps 54 Mbps hide-ssid Hides the SSID. When enabled, the SSID will not be visible for the users. — Disabled hotspot-profile Associates a hotspot profile with the WLAN SSID profile.
Command/Parameter Description Range Default the broadcast probe requests sent by clients to search for the available SSIDs and ignores the probe request if required, mac-authentication Enables MAC authentication for clients that use this SSID profile. — Disabled mac-authentication-delimiter Allows you to set a delimiter that can be used in the MAC address string for MAC authentication. colon or dash — You can specify colon or dash for delimiter.
Command/Parameter Description Range Default — — opensystem, wpa2-aes, wpa2-pskaes, wpa-tkip, wpa-psk-tkip, wpa-tkip wpa2-aes, wpa-psk-tkip wpa2-pskaes, staticwep, dynamic-wep opensystem traffic can be sent at the rate of 1-24 Mbps. The default rate for sending frames for 2.4 GHz is 1 Mbps and 5.0 GHz is 6 Mbps. okc-disable Disables opportunistic key caching (OKC). In the OKC based roaming, the AP stores one pairwise master key (PMK) per client, which is derived from last 802.
Command/Parameter Description Range Default 1—65535 Kbps — — Disabled — userauthentication TKIP encryption using a pre-shared key. per-user-bandwidth-limit l wpa-tkip, wpa2-aes—WPA with TKIP and WPA2 with AES encryption. l wpa-psk-tkip,wpa2-psk-aes - WPS with TKIP and WPA2 with AES encryption using a pre-shared key. l static-wep—WEP with static keys. l dynamic-wep—WEP with dynamic keys. Configures a bandwidth limit in Kbps for the SSID users.
Command/Parameter Description Range Default radius-interim-accountinginterval Configures an interval for posting accounting information as RADIUS INTERIM accounting records to the RADIUS server. Any integer value in minutes — Any integer value in minutes — When configured, the W-IAP sends interim-update messages with current user statistics to the RADIUS server at regular intervals.
Command/Parameter Description Range Default L3 authentication (captive portal authentication): When reauthentication succeeds, a preauthentication role is assigned to the client that is in a post-authentication role. Due to this, the clients are required to go through captive portal to regain access. rf-band Configures the radio frequency band on which this SSID will be broadcast. You can select either 2.4GHz, 5 GHz, or all to specify both bands. 2.
Command/Parameter Description l value-of - This rule sets the user role to the value of the attribute returned. To set a user role, the value of the attribute must already be configured on the W-IAP. l matches-regularexpression—The rule is applied only if the attribute value matches the regular expression pattern specified in Operand. This operator is available only if the mac-address-anddhcp-options attribute is selected in the Attribute drop-down.
Command/Parameter Description |value-of} following conditions: termination l contains—The rule is applied only if the attribute value contains the specified string. l ends-with—The rule is applied only if the attribute value ends with the specified string. l equals—The rule is applied only if the attribute value is equal to the specified string. l not-equals—The rule is applied only if the attribute value is not equal to the specified string.
Command/Parameter Description Range Default terminating the authorization protocol on the W-IAP. By default, for 802.1X authorization, the client conducts an EAP exchange with the RADIUS server, and the W-IAP acts as a relay for this exchange. The W-IAP by itself acts as an authentication server and terminates the outer layers of the EAP protocol, only relaying the innermost layer to the external RADIUS server.
Command/Parameter Description Range Default wmm-video-share Allocates bandwidth for video traffic generated from video streaming. — — wmm-voice-dscp Allows you to specify the DSCP mapping value for the voice traffic. 0—63 — wmm-voice-share Allocates bandwidth for voice traffic generated from the incoming and outgoing voice communication.
(Instant AP)(SSID Profile "employee1")# expression ..
Command Information W-IAP Platform Command Mode All platforms Configuration mode and WLAN SSID profile configuration submode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
wlan sta-profile wlan sta-profile essid cipher-suite wpa-passphrase uplink-band no… Description This command enables Wi-Fi uplink on a W-IAP. Syntax Command/Parameter Description Range Default wlan sta-profile Configures a Wi-Fi uplink profile for a W-IAP. — — essid Defines a unique name for the network on which the Wi-Fi uplink will be enabled. — — cipher-suite {clear| wpa-tkippsk| wpa2-ccmp-psk} Configures encryption settings.
Example The following commands configure the Wi-Fi uplink profile: (Instant (Instant (Instant (Instant (Instant AP)(config) # wlan sta-profile AP)(sta uplink)# uplink-band dot11a AP)(sta uplink)# uplink-band dot11a AP)(sta uplink)# cipher-suite wpa-tkip-psk AP)(sta uplink)# wpa-passphrase user@123 Command History Version Description Dell Networking W-Series Instant 6.2.1.03.3 This command is introduced.
wlan tacacs-server wlan tacacs-server ip port key timeout retry-count deadtime no... Description This command is used to configure a TACACS server for management users. Syntax Command/Parameter Description Default wlan tacacs-server Configures the TACACS server profile. - ip Configures the IP address of the TACACS server.
Command History Version Description Dell Networking W-Series Instant 6.4.0.2-4.1 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Configuration mode and TACACS server profile sub-mode. 0511587-03 | September 2014 Dell Networking W-Series Instant 6.4.2.0-4.1.
wlan walled-garden wlan walled-garden white-list black-list no… Description This command configures a walled garden to control user access to the web content and services. The walled garden access is required when an external captive portal is used. Syntax Command/Parameter Description Range wlan walled-garden Creates a Walled Garden profile for the W-IAP. white-list Configures a whitelist of URLs to allow the authenticated users to access to a specific domain.
When a user attempts to navigate to other websites not in the whitelist of the walled garden profile, the user is redirected to the login page. Similarly, a blacklisted walled garden profile blocks the users from accessing some websites.
wlan wispr-profile wlan wispr-profile wispr-location-id-ac wispr-location-id-cc wispr-location-id-isocc wispr-location-id-network wispr-location-name-location wispr-location-name-operator-name no... Description This command configures a Wireless Internet Service Provider roaming (WISPr) authentication profile for a WIAP.
Example The following commands configure a WISPr authentication profile: (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant (Instant AP)(config)# wlan wispr-profile AP)(WISPr)# wispr-location-id-ac 408 AP)(WISPr)# wispr-location-id-cc 1 AP)(WISPr)# wispr-location-id-isocc US AP)(WISPr)# wispr-location-id-network wispr AP)(WISPr)# wispr-location-name-location airport AP)(WISPr)# wispr-location-name-operator-name KNP AP)(WISPr)# end AP)# commit apply Command History Version Description
write write {erase |memory} Description This command saves the running configuration to memory or displays the running configuration on the screen. This command can also be used to erase the running configuration and return to factory default setting Syntax Parameter Description erase Erases the running system configuration file. Rebooting the W-IAP resets it to the factory default configuration.
xml-api-server xml-api-server ip key no... Description This command integrates an XML API interface to the W-IAP. Syntax Command/Parameter Description xml-api-server Displays the sub-mode for configuring the XML API interface parameters. ip Configures the IP address of the XML API server. key Configures the key required for accessing the XML API interface. no… Removes the configured parameter.
zonename zonename no… Description This command configures a zone name for the W-IAP. You can configure zone settings on a W-IAP and the SSID profile, to assign an SSID to a specific W-IAP. Syntax Parameter Description zonename Configures zone on a W-IAP. no… Removes the configuration. Usage Guidelines Use this command to configure an AP zone. To assign an SSID to a specific W-IAP, the AP zone name must be configured on the WLAN SSID profile.
Terminology Acronyms and Abbreviations The following table lists the abbreviations used in this document.
Table 10: List of abbreviations Abbreviation Expansion NS Name Server NTP Network Time Protocol PEAP Protected Extensible Authentication Protocol PEM Privacy Enhanced Mail PoE Power over Ethernet RADIUS Remote Authentication Dial In User Service VC Virtual Controller VSA Vendor-Specific Attributes WLAN Wireless Local Area Network Glossary The following table lists the terms and their definitions used in this document. Table 11: List of Terms Term Definition 802.
Table 11: List of Terms Term Definition 802.11g Offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b. 802.11g operates in the 2.4 GHz band and employs orthogonal frequency division multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speeds of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. 802.
Table 11: List of Terms Term Definition DNS Server A Domain Name System (DNS) server functions as a phonebook for the Internet and Internet users. It converts human readable computer hostnames into IP addresses and vice-versa. A DNS server stores several records for a domain name such as an address 'A' record, name server (NS), and mail exchanger (MX) records.
Table 11: List of Terms Term Definition The choice of endspan or midspan depends on the capabilities of the switch to which the W-IAP is connected. Typically if a switch is in place and does not support PoE, midspan power injectors are used. PPPoE Point-to-Point Protocol over Ethernet (PPPoE) is a method of connecting to the Internet typically used with DSL services where the client connects to the DSL modem.
Table 11: List of Terms Term Definition WEP Wired equivalent privacy (WEP) is a security protocol specified in 802.11b, designed to provide a WLAN with a level of security and privacy comparable to what is usually expected of a wired LAN.
