Reference Guide Dell Networking W-Series Instant Access Point 6.3.1.1-4.
Copyright © 2013 Aruba Networks, Inc. Aruba Networks trademarks include , Aruba Networks®, Aruba Wireless Networks®, the registered Aruba the Mobile Edge Company logo, and Aruba Mobility Management System®. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc. All rights reserved. Specifications in this manual are subject to change without notice. Originated in the USA. All other trademarks are the property of their respective owners.
Contents Contents ................................................................................................... 3 Chapter 1 About this Guide ...................................................................................... 5 Document Organization.........................................................................................5 Format of Messages..............................................................................................5 Severity Levels ................................
Information Messages .........................................................................................89 Debug Messages.................................................................................................89 Chapter 6 ARM Messages ...................................................................................... 91 Error Messages....................................................................................................91 Warning Messages ....................................
Chapter 1 About this Guide This document covers syslog messages included in this Dell Networking W-Series Instant Access Point release. In this edition, message definition, recommended action and in some cases the cause that generated the syslog message are included. Syslog messages were prioritized for definition; this edition includes definitions for approximately 70% of Dell W-Instant syslog messages. For those messages yet to be defined, the phrase “No description available” appears.
= 06B408550367 = 00:12:0e:44:d4:2c These substitutions generate message text as follows: AM 00:0b:86:38:5d:b0: Interfering AP detected with SSID 06B408550367 and BSSID 00:12:0e:44:d4:2c In the following chapters, messages are defined in generic terms with variables shown to indicate where substitutions of actual data will occur. Severity Levels The severity levels defined for syslogs are outlined in Table 1, which orders the severity from most to least severe.
Syslog Server To specify a Syslog Server for sending syslog messages to the external servers, navigate to System > Show advanced options > Monitoring in the Dell W-Instant UI and update the following fields. Syslog server— Enter the IP address of the server to send system logs. Syslog level— For a global level configuration, select one of the logging levels from the standard list of syslog levels. The default value is Notice.
information kept in the system logs is important. The capabilities required for handling logs should include the following: Efficient log management Sophisticated analysis capabilities Consistent report generation Scalability Security Analyzing system logs, and extracting relevant information from them, requires an efficient pattern matching engine, where the desired patterns can be created with standard pattern matching commands, such as a regular expression engine.
Chapter 2 Security Messages Critical Messages Table 4 Security Critical Messages Message ID Message and Description 132002 Enabling dot1x termination for AP [mac:%m] [auth_profile:%s] before cert download. Description: Termination is being enabled before certificate is downloaded. 132014 “AP [bssid:%m] [apname:%s] Incomplete AP configuration. Check if WEP Key, WEP Transmit Key or WPA Passphrase is not configured. Description: AP’s configuration is not complete.
Error Messages Table 5 Security Error Messages Message ID Message and Description 121000 Failed to calculate the HMAC-MD5 digest. Description: Controller failed to calculate the HMAC-MD5 digest for RADIUS packet due to an internal error. Recommended Action: If the problem persists, contact Aruba support provider. 121001 Error [errno:%d],[errstr:%s] receiving packet [packet_len:%d], fd=[fd:%d]. Description: A socket error occurred while receiving RADIUS server response.
Table 5 Security Error Messages (Continued) Message ID Message and Description 121014 Received invalid reply digest from RADIUS server. Description: The reply digest received from the RADIUS server doesn’t match the calculated digest. Recommended Action: Check the RADIUS server is configured properly and verify shared secret configuration on the controller matches that on the RADIUS server. 121016 RADIUS server [server:%s],[fqdn:%s][ipaddr:%s] is out of sequence.
Table 5 Security Error Messages (Continued) Message ID Message and Description 121036 RADIUS: Error [errno:%d],[errstr:%s] setting client socket options. Description: Internal error occurred while setting connection options with the RADIUS server. Recommended Action: Contact Aruba technical support if this problem persists. 121047 Failed to add user Port ID in the Radius Accounting Pkt [pkt:%s]. Description: This shows an internal debug message. 121048 Unknown result type [resultType:%d].
Table 5 Security Error Messages (Continued) Message ID Message and Description 132016 Local Database Server not available to cache the machine auth for user [name:%s] [mac:%m]. Description: Internal server is not available for caching the machine authentication for the specified User. Recommended Action: Run the aaa test-server pap internal command to verify connectivity to the local database server.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132029 Station [mac:%m] [bssid:%m] sent Unsupported EAPOL Type [type:%d]. Description: Station sent an unsupported EAPOL packet. Recommended Action: Ensure the station is configured properly to perform EAP authentication. If the problem persists, check for packet-corruption by capturing sniffertraces between client, AP and controller. 132030 Dropping EAPOL packet sent by Station [mac:%m] [bssid:%m].
Table 5 Security Error Messages (Continued) Message ID Message and Description 132040 Station [mac:%m] [bssid:%m] sent Unsupported MD5 EAP type [eaptype:%d]. Description: Station sent an EAP packet that is not supported. Ensure the station is configured correctly to perform an EAP authentication method that is supported by the Aruba controller. Ensure that the aaa-profile associated with the authentication request matches the authentication-method the client is sending to authenticate.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132057 Failed to send the radius request for Station [mac:%m] [bssid:%m]. Description: Radius request for specified station is being dropped due to lack of system resources. Recommended Action: Free up system memory and other resources by throttling userauthentication requests. 132059 Multicast Key type of the AP [bssid:%m] [apname:%s] is not static-wep or dynamic-wep.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132075 Multicast cipher from Station [mac:%m] [stmc:%X] does not match with AP [bssid:%m] [apmc:%X] [apname:%s]. Description: Mismatch in the multicast ciphers specified by the station and AP. Recommended Action: Identify the station and investigate why it is sending incorrect data. 132076 Station [mac:%m] [bssid:%m] [apname:%s] sent invalid number of unicast ciphers [uc:%d].
Table 5 Security Error Messages (Continued) Message ID Message and Description 132089 Invalid WPA [ver:%d] Key message from Station [mac:%m] [bssid:%m] [apname:%s],reason: Error flag without Request bit set. Description: WPA key message with error flag without request bit set was received from the station. This is invalid. 132090 Received TKIP Michael MIC Failure Report from the Station [mac:%m] [bssid:%m] [apname:%s]. Description: Specified Station sent TKIP MIC failure report.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132156 Station [mac:%m] [bssid:%m] sent inner EAP Start Description: Station sent inner EAP start packet. This is invalid. 132157 Station [mac:%m] [bssid:%m] sent inner EAP packet with more-fragments bit set. Description: Station sent inner EAP packet with more fragment bit set. This is invalid. 132158 Station [mac:%m] [bssid:%m] sent invalid EAP flag. Description: Station sent invalid flag in the inner EAP packet.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132196 Invalid EAP TLV-Type [tlv_type:%d] in the EAP-TLV/Phase2 response from Station [mac:%m] [bssid:%m]. Description: Station sent invalid TLV type. 132197 Maximum number of retries was attempted for station [name:%s] [mac:%m] [bssid:%m], deauthenticating the station. Description: Maximum number of retries was attempted for station to complete the authentication phase. Recommended Action: Deauthenticating the station.
Table 5 Security Error Messages (Continued) Message ID Message and Description 132211 Station [mac:%m] [bssid:%m] sent a cert from which we couldn’t extract the public key. Description: Station sent a cert from which we couldn’t extract the public key. 132212 Station [mac:%m] [bssid:%m] certificate signature verification failed. Description: Station sent a cert, but the certificate signature verification failed. 132217 Failed to convert cert into DER format before sending to certmgr.
Table 6 Security Warning Messages Message ID Message and Description 121006 RADIUS server [name:%s]-[fqdn:%s]-[ipaddr:%s]-[sin_port:%u] timeout for client=[cbuf:%s] auth method [server:%s]. Description: RADIUS Server is unreachable. The server could be down or there is connectivity problem. Recommended Action: Check RADIUS server connectivity . 121007 RADIUS (RFC 3576): Ignoring request from client [srv_ipaddr:%s] port([srv_port:%d]) with unknown code [code:%d].
Table 7 Security Notice Messages Message ID Message and Description 106014 AM: Wireless tarpit containment: Sending Auth reply for frame from AP [bssid:%m] to STA [mac:%m] on channel [channel:%d] with algorithm [alg:%d] transaction [xn:%d] seq [seq:%d]. Description: No description available. 106015 AM: Wireless tarpit containment: Sending Assoc-Response for frame from AP [bssid:%m] to STA [mac:%m] on channel [channel:%d] with aid [aid:%d] seq [seq:%d]. Description: No description available.
Table 8 Security Information Messages Message ID Message and Description 132019 Station [name:%s] [mac:%m] was Machine authenticated. Description: Station successfully authenticated the machine account. 132020 Station [name:%s] [mac:%m] failed Machine authentication update role [rl:%s]. Description: Station failed to authenticate the machine account. 132021 Station [mac:%m] [bssid:%m] entered Held state. Description: Authenticator is in the held state for the specified station.
Table 8 Security Information Messages Message ID Message and Description 132134 WPA Countermeasure is disabled. Description: WPA Countermeasure is disabled. 132202 Successfully downloaded the certs [rootcert:%s] [servercert:%s] for EAP termination. Description: Successfully downloaded the certificates for EAP termination. 132218 Skipping certificate common name check for username=[user:%s] MAC=[mac:%s].
Table 9 Security Debug Messages Message ID Message and Description 121050 [msg:%s] Description: This is an internal RADIUS debug log. 132007 Clearing Station state on AP [bssid:%m]. Description: Station is forced to be cleared from the AP’s stations table. 132022 Station [mac:%m] [bssid:%m] sent 802.1x packet before association/l2 miss - dropping packet. Description: Received an EAP packet from the station before receiving an association/ l2 miss message.
Chapter 3 System Messages Emergency Messages Table 10 System Emergency Messages Message ID Message and Description 330203 MESHD process initialization failed. Cause: MESHD process initialization failed possibly because the mesh-node is not correctly provisioned. Recommended Action: Re-provision the AP. Contact Dell technical support if this problem persists. 330204 MESHD process exiting. No MESH role was specified. Cause: No MESH role was specified. Recommended Action: Re-provision the AP.
Critical Messages Table 12 Critical System Messages Message ID Message and Description 341006 [msg:%s] Description: No description available. 341275 VPN tunnel switch to [tunnel:%s], reason:[reason:%s]. Recommended Action: VPN tunnel switch. 341279 Managed mode: Could not download the configuration from the server. Description: Could not download the configuration from the server.
Table 13 Error System Messages (Continued) Message ID Message and Description 304054 Client blacklist is full and caused an entry to not be added. Limit: [limit: %d]. Description: This log indicates that the client blacklist table is full and an entry that would have been added could not be added. 304055 Contact Aruba tech-support.“Unexpected stm (Station management) runtime error at [func:%s], [line:%d], [data:%s]. Description: Unexpected condition occurred in the station manager (stm).
Table 13 Error System Messages (Continued) Message ID Message and Description 311019 Unable to generate certificate signing request (CSR). AP will reboot. Description: The access point was unable to generate a certificate signing request (CSR). Recommended Action: Contact your support provider. 311020 An internal system error has occurred at file [file:%s] function [function:%s] line [line:%d] error [error:%s]. Description: This log indicates that we encountered an internal system error.
Table 13 Error System Messages (Continued) Message ID Message and Description 326267 An internal system error has occurred at file [file:%s] function [function:%s] line [line:%d]. Description: This log indicates that we encountered an internal system error. Recommended Action: Contact your support provider. 326268 An internal system error has occurred at file [file:%s] function [function:%s] line [line:%d] error [error:%s]. Description: This log indicates that we encountered an internal system error.
Table 13 Error System Messages (Continued) Message ID Message and Description 330212 System encountered an internal communication error. Error occurred when message is being sent from source application [src:%s] destination application [dst:%s] at file [file:%s] function [func:%s] line [line:%d]. Description: This log indicates that application processes in the system encountered an error sending messages to each other. This could be a transient condition and the problem might go away.
Table 13 Error System Messages (Continued) Message ID Message and Description 341041 AP basic verify image-[image:%s] fail. Description: The AP is upgrading image. 341042 AP check image-[image:%s] version for mesh fail. Description: The AP is upgrading image. 341044 AP can't open MTD device-[device:%s]. Description: The AP is setuping image. 341047 AP regulatory domains don't match Master-[id1:%d], slave-[id2:%d]. Description: The AP is upgrading image.
Table 13 Error System Messages (Continued) Message ID Message and Description 341072 AP could not find post auth role [name:%s]. Description: The AP is creating SSID. 341074 AP can't find essid-[name:%s]. Description: The AP is creating SSID. 341081 No space for acl-[name:%s]. Description: The AP is configuring ACL. 341082 ACL index-[index:%d] is invalid. Description: The AP is configuring ACL. 341083 ACL index-[index:%d] is inuse. Description: The AP is configuring ACL.
Table 13 Error System Messages (Continued) Message ID Message and Description 341114 [func:%s]: set gre name-[name:%s] fail. Description: AP is setting gre name. 341116 [func:%s]: clr gre name-[name:%s] fail. Description: AP is setting gre name. 341118 [func:%s]: create session fail for ip-[ipaddr:%s]. Description: AP is creating session. 341119 [func:%s]: SID not match for IP-[ip:%s] sid-[sid:%s]. Description: Handle papi message. 341122 [func:%s]: Malloc fail [num:%d].
Table 13 Error System Messages (Continued) Message ID Message and Description 341232 Fail to retrieve ap config from flash after [retry:%d] retries. Description: fail to retrieve ap config from flash. 341235 Add [mac:%s] to subscription ap list failed. Description: Add ap to subscription ap list failed. 341270 Set priority failed, failed to find type [type:%d], sub port [port:%d], priority [priority:%d]. Description: Set priority failed. 341271 Ethernet uplink [uplink_name:%s] link down.
Table 14 Warning System Messages (Continued) Message ID Message and Description 304013 tunnel_timeout: Tunnel 0x[tunnel_id:%x] not found. Description: No description available. 304014 received frame of unknown type [type:%x] (subtype [stype:%x]). Description: No description available. 304015 handle_tunnel_info_request: Tunnel [tunnel_id:%d] not found. Description: No description available. 304016 IP [tunnel_ip:%p] MAC [mac:%m] ARP Query failed. Description: No description available.
Table 14 Warning System Messages (Continued) Message ID Message and Description 304048 User DB query issue in: [call: %s]. SQL command: [cmd: %s]. Description: This log indicates that there was an issue when a command was executed on the user database. 304050 Client blacklist purged by Administrator. Description: This log indicates that the client blacklist was purged by the administrator. 311000 Attempt to change LMS of remote AP ignored. Description: No description available.
Table 14 Warning System Messages (Continued) Message ID Message and Description 326085 AM: Setting collection of statistics to : [mode:%s]. Description: No description available. 326096 AM: message too long [bl:%d]. Description: No description available. 326157 AM: Too many Wi-Fi(s) interfaces = [wifi_index:%d]. Description: No description available. 326158 “AM: MAX_SIZE = [DET_STATS_READ:%d], actual size = [det_proc_stats_size:%d]. Description: No description available.
Table 14 Warning System Messages (Continued) Message ID Message and Description 341102 Incorrect format for message type[type:%d]:[msg_len:%d]:[recv_len:%d]:[bytes_read:%d]:[from_ip:%s]:[from_port:% d]. Description: Handle papi message. 341103 Unknown version from [ipaddr:%s] in message type-[type:%d]. Description: Handle papi message. 341104 Invalid version for message type-[type:%d] from [ipaddr:%s] (local [ver:%s] vs. master [m_ver:%s]). Description: Handle papi message.
Table 14 Warning System Messages (Continued) Message ID Message and Description 341177 Try next uplink because current uplink is down - [type:%s]. Description: Try next uplink. 341181 Setup ip for uplink - [type:%s]. Description: Setup ip for uplink interface. 341182 Setup vpn for rap conversion - [ip:%s]. Description: Setup vpn for rap conversion. 341183 Downloading rap image via vpn - url [url:%s]. Description: Downloading rap image via vpn.
Table 14 Warning System Messages (Continued) Message ID Message and Description 341250 VC record delta configuration, malloc error. len [len:%d] port [port:%d] flags [flags:%d] seq [seq:%d] case [case:%s]. Description: VC record delta configuration, malloc error. 341252 VC send delta configurations to ap error. ap [ap_ip:%s] ap_cfg_id [acid:%d] current_cfg_id [cid:%d] top_cfg_id [tid:%d] case [case:%s]. Description: VC send delta configuration to ap error.
Notice Messages Table 15 Notice System Messages Message ID Message and Description 304006 IGMP Drop Tx - [s_addr:%p] Description: No description available. 304007 IGMP Join Tx - [s_addr:%p] Description: No description available. 304031 PAPI message to [ip:%p] port [port:%d] timed out. Description: No description available. 304032 902il Compatibility mode [enadis:%s] Description: NEC 902il compatibility mode was enabled or disabled.
Table 15 Notice System Messages (Continued) Message ID Message and Description 326101 AM: length mismatch for message [msg_type:%d], expected [bytes_read:%d], got [msg_len:%d]. Description: No description available. 326102 AM: unable to find AP [bssid:%s]. Description: No description available. 326106 AM: unable to find STA [bssid:%s] PHY [phy_type:%d]. Description: No description available. 326107 AM: RSTA Type set to [rap_type:%d] for STA [bssid:%s]. Description: No description available.
Table 15 Notice System Messages (Continued) Message ID Message and Description 326276 AM: Inactive AP Detected SSID = [ssid:%s] BSSID = [bssid_str:%s]. Description: No description available. 326277 AM: Setting RAP Type for AP [bssid_str:%s] to: [rap_str:%s]. Description: No description available. 326278 AM: STA [mac_addr:%s] Authenticated with AP [bssid_str:%s]. Description: No description available. 341003 [msg:%s Description: No description available.
Table 15 Notice System Messages (Continued) Message ID Message and Description 341156 Sending image err [state:%s] to [ap_ip:%s]. Description: Send image err state to Master. 341157 AP reaches count [count:%d]-[msg:%s]. Description: AP image upgrade timeout. 341158 [func:%s],[line:%d]: Setup image with code [ret:%d]. Description: AP image upgrade timeout. 341201 AP [name:%s] reports a spectrum alert: non-wifi device(ID: [id:%d],type: [type:%s]). Description: Non-wifi device is detected.
Table 16 Information System Messages (Continued) Message ID Message and Description 304057 [msg:%s] AP Heartbeat Tunnel Timeout indication from Datapath. Description: No description available. 304068 [func:%s], [line:%d]: STM restarts and notifies datapath to clean up users. Description: STM restarts and notifies datapath to clean up users. 311001 LMS changed from [old_ip:%p] to [new_ip:%p]. Description: No description available. 326000 AM initialized. Description: Air Monitor is starting.
Table 16 Information System Messages (Continued) Message ID Message and Description 341010 AP [name:%s] is up. Description: The AP has registered with the virtual controller. 341014 AP rebooting [reason:%s]. Description: The AP is rebooting. 341015 AP is operating in regulatory [domain:%s] [code:%d]. Description: The AP is in specified regulatory domain. 341016 AP is operating in creating auth server-[name:%s], add-[flag:%d]. Description: The AP is configuring auth server.
Table 16 Information System Messages (Continued) Message ID Message and Description 341073 AP derived acl for post auth role-[name:%s], idx-[idx:%u], acl-[acl:%u]. Description: The AP is creating SSID. 341075 [func:%s] AP can't find default post auth acl for SSID-[name:%s]. Description: The AP is creating SSID. 341076 Using default acl-[acl:%d] for SSID-[name:%s]. Description: The AP is creating SSID. 341077 AP add new acl-[name:%s], idx-[id:%d], vlan-[vid:%d], caleaOn-[on:%d].
Table 16 Information System Messages (Continued) Message ID Message and Description 341112 [func:%s]: cert key is [psk:%s]. Description: AP is setting cert. 341115 [func:%s]: set gre [ipaddr:%s] successfully. Description: AP is setting gre name. 341117 [func:%s]: clear gre successfully. Description: AP is setting gre name. 341120 SNMP get next mac-[mac:%s], index-[index:%d]. Description: SNMP action. 341121 SNMP return [mac:%s]:[num:%d]. Description: SNMP action.
Table 16 Information System Messages (Continued) Message ID Message and Description 341178 [func:%s],[line:%d]: send message to awc [type:%d], [username:%s], [password:%s], [device_key:%s], [label:%s]. Description: clid send papi message to awc. 341179 [func:%s],[line:%d]: receive message from awc [key:%s], [state:%d], [value:%s]. Description: clid receives message from awc. 341180 [func:%s],[line:%d]: send mesh cfg. Description: Send mesh cfg. 341186 Find uplink fail, type [type:%d].
Table 16 Information System Messages (Continued) Message ID Message and Description 341209 [func:%s]: mip tunnel down [tid:%d]. Description: MIP tunnel down. 341215 [func:%s]: L3 Subnet Update [cmd:%d] [subnet:%s] [mask:%s] [vlan:%d] [vcip:%s] [flag:%x]. Description: L3 Subnet Update. 341216 [func:%s]: awc logout from [ip:%s]. Description: Awc logout. 341217 [func:%s]: awc connect to [ip:%s] successfully. Description: Awc connect successfully. 341218 [func:%s]: awc login to [ip:%s] successfully.
Debug Messages Table 17 Debug System Messages Message ID Message and Description 304003 [msg:%s] Description: System related debugging messages logged in the station manager (stm). 304008 [msg:%s] Description: No description available. 304021 [func:%s]:[line:%d] Flow [flow_id:%d] not found. Description: No description available.
Table 17 Debug System Messages (Continued) Message ID Message and Description 304070 Sending msg STM to HTTP mgmt-server [protocol:%s] [hostname:%s] [port:%d] [identifier:%s] radios:[nradios:%d] vaps:[nvaps:%d] stas:[stas:%d] unassoc_stas:[unassoc_stas:%d] ap_info:[ap_info:%d] radio_info:[radio_info:%d] vap_info:[vap_info:%d] ap_sys_info:[ap_sys_info:%d]. Description: This log displays a record of the transmission of the AMON message from STM to the http management server.
Table 17 Debug System Messages (Continued) Message ID Message and Description 304083 Adding RADIO_INFO records, count [num_records:%d]. Description: This log indicates the number of radio info records added to the AMON message buffer. 304084 Sent a total of [num_records:%d] RADIO_INFO records. Description: This log indicates the total number of radio info records sent to the management server. 304085 Adding VAP_INFO records, count [num_records:%d].
Table 17 Debug System Messages (Continued) Message ID Message and Description 326092 AM: [line:%d]: Sending PROBE_STATS_UPDATE_MESSAGE for STAs of length [bl:%d] Description: No description available. 326093 AM: [line:%d]: Sending STM_AP_STATS_UPDATE for STAs of length [bl:%d] Description: No description available. 326094 AM:SM: Sending Spectrum Register Message for radio [r:%d] band [band:%s] to [ip:%s]. Description: This log indicates that spectrum radio is registering with the controller.
Table 17 Debug System Messages (Continued) Message ID Message and Description 341131 AP sends meshd parameters [cs_key:%s]-[key:%s]-[country_code:%d]. Description: AP is sending mesh parameters. 341132 Check sum error for AP-[ip:%s], slave [s_sum:%u] vs master [m_sum:%u]. Description: AP is checking configuration. 341133 Find AP-[ip:%s] fail. Description: AP is receiving stats sync. 341137 Client [mac:%s] was removed. Description: AP remove client when timeout.
Table 17 Debug System Messages (Continued) Message ID Message and Description 341246 VC set delta configuration current_cfg_id [cid:%d] top_cfg_id [tid:%d]. Description: New master set its own celta cfg id 341247 VC need shrink delta configuration entrys. current_cfg_id [cid:%d] top_cfg_id [tid:%d] max [mid:%d]. Description: VC need shrink delta configuration entrys. 341248 VC delta configuration entry list is empty. Description: VC delta configuration entry list is empty.
Chapter 4 User Messages Error Messages Table 18 User Error Messages Message ID Message and Description 524005 Invalid action :[file:%s],[func:%s],[line:%d],[action:%d]. Description: This shows internal debug messages. 524006 [file:%s], [func:%s],[line:%d],cur=0x[cur:%x],end=0x[end:%x]. Description: This shows internal debug messages. 524007 [file:%s], [func:%s],[line:%d], realloc size invalid, tot=:[tot:%d],certlen=:[len:%d]. Description: This shows internal debug messages.
Table 18 User Error Messages 60 | User Messages Message ID Message and Description 524027 Error decoding MPPE send-key (code = [code:%d]). Description: This shows internal debug messages. 524028 Invalid MPPE send-key length:[len:%d]. Description: This shows internal debug messages. 524030 Invalid Radius Code [radcode:%d]. Description: This shows internal debug messages. 524043 [string:%s]: FT mic=[string1:%s]. Description: This shows internal debug messages.
Table 18 User Error Messages Message ID Message and Description 524068 AES-GCM key setting is allowed only for Tunnel mode VAP's. Description: This shows internal debug messages. 541012 [func:%s]: [line:%d]: find client-[mac:%m] fail. Description: Station sync. 541017 [func:%s]: parse tlv ret-[ret:%d] mac-[mac:%m] fail. Description: Station sync. 541018 [func:%s],[line:%d]: could not find client-[mac:%m]. Description: AP is looking up station.
Table 19 User Warning Messages 62 | User Messages Message ID Message and Description 501062 Station [sta:%m]: Ignored ATIM to BSSID [bss:%m] on AP [name:%s]. Description: No description available. 501064 Station [sta:%m]: Ignored unknown management frame subtype [stype:%x]h to BSSID [bss:%m] on AP [name:%s]. Description: No description available. 501067 Source: [sa:%m] Failed AP [ip:%p]-[bssid:%m]-[name:%s] Rates Mismatch STA 0x[rates:%x] AP 0x[tx_rates:%x]. Description: No description available.
Table 19 User Warning Messages Message ID Message and Description 501086 Probe request: [mac:%m]: Invalid Station MAC address from AP [ip:%P]-[bssid:%m][name:%s] SSID [essid:%s]. Description: No description available. 501091 Auth request: [mac:%m]: Invalid Station MAC address from AP [ip:%P]-[bssid:%m][name:%s]. Description: No description available. 501092 Auth request: [mac:%m]: Dropped AP [ip:%P]-[bssid:%m]-[name:%s] for STA DoS protection. Description: No description available.
Table 19 User Warning Messages 64 | User Messages Message ID Message and Description 501124 Addts req: [mac:%m]: AP [ip:%P]-[bssid:%m]-[name:%s] refused. Voice Capacities Reached. Description: No description available. 501125 Addts req: [mac:%m]: AP [ip:%P]-[bssid:%m]-[name:%s] refused. Flow Setup Failed. Description: No description available. 501127 Delts: [mac:%m]: AP [ip:%P]-[bssid:%m]-[name:%s] STA Not found. Description: No description available.
Notice Messages Table 20 User Notice Messages Message ID Message and Description 501001 Station [sta:%m]: Trying to associate to BSSID [bss:%m] on AP [name:%s] before authentication. Description: No description available. 501002 Station [sta:%m]: ESSID length error trying to associate to BSSID [bss:%m] on AP [name:%s], length [len:%d]. Description: No description available.
Table 20 User Notice Messages 66 | User Messages Message ID Message and Description 501081 Deauth to sta: [mac:%m]: Ageout AP [ip:%P]-[bssid:%m]-[name:%s] [reason:%d]. Description: No description available. 501084 Probe request: [mac:%m]: Dropped AP [ip:%P]-[bssid:%m]-[name:%s] for STA DoS protection. Description: No description available. 501087 Probe request: [mac:%m]: Dropped AP [ip:%P]-[bssid:%m]-[name:%s] for STA DoS protection SSID [essid:%s]. Description: No description available.
Table 20 User Notice Messages Message ID Message and Description 501108 Deauth to sta: [mac:%m]: AP [ip:%P]-[bssid:%m]-[name:%s] Configuration Change. Description: No description available. 501109 Auth request: [mac:%m]: AP [ip:%P]-[bssid:%m]-[name:%s] auth_alg [auth_alg:%d]. Description: No description available. 501110 Auth failure: [mac:%m]: AP [ip:%P]-[bssid:%m]-[name:%s] Reason [resp:%d]. Description: No description available.
Table 20 User Notice Messages Message ID Message and Description 501159 STA [mac:%m]: VHT Capabilities element too short ([len:%d]); ignoring. Description: No description is available. 501189 No available vlan in sta_vlan_id. Cannot take [mac:%m] association request. Description: Station manager does not have available configured vlan to accept association request. 501190 Vlan assignment algorithm not set. Cannot take [mac:%m] association request.
Table 21 User Information Messages Message ID Message and Description 541032 [func: %s]: allocate accounting session id, user-[mac:%m] id-[id:%u]. Description: learning client usrname. 541034 func: %s]: set user idle timeout, user-[mac:%m] timeout-[to:%u]. Description: Set user idle timeout. 541035 Set user agent str for [mac:%m] detail-[us:%s]. Description: Set user agent info. 541036 [func:%s]: send idle timeout, sta [mac:%m] , idle time-[time:%d]. Description: Station update.
Table 22 User Debug Messages 70 | User Messages Message ID Message and Description 501065 [msg:%s] Description: No description available. 501066 Source: [sa:%m] Failed AP [ip:%P]-[bssid:%m]-[name:%s] SSID Mismatch. Description: No description available. 501082 Probe request: [mac:%m]: AP [ip:%P]-[bssid:%m]-[name:%s]. Description: No description available. 501085 Probe request: [mac:%m]: AP [ip:%P]-[bssid:%m]-[name:%s] SSID [essid:%s]. Description: No description available.
Table 22 User Debug Messages Message ID Message and Description 501157 Station [sta:%m]: Unexpected SA-Query Response bss [bss:%m]. Description: No description available. 501158 Station [sta:%m]: SA-Query Request from non-MFP STA to bss [bss:%m]. Description: No description available. 501160 [msg:%s] Description: No description available. 501161 Client Match Received probe report: AP [ap:%s] ESSID [essid:%s] Assoc ESSID [a_essid:%s] for client [mac:%s] with signal [sig:%d].
Table 22 User Debug Messages 72 | User Messages Message ID Message and Description 501173 Client Match: LoadBal Adding pot sta [mac:%m] for move from AP [name:%s] [bss:%m] Current SNR [snr:%d]. Description: No description is available. 501174 Client Match: Deleting BSS [bss:%m] from client [mac:%m] AP may be down or AM. Description: No description is available. 501175 Client Match: Deleting STA [mac:%m] from VBR table. Description: No description is available.
Table 22 User Debug Messages Message ID Message and Description 501196 Update dhcp-opt: [mac:%m] Update dhcp-opt [vlan:%d] [vlanhow:%s] [role:%d] rule_index [index:%x] essid [essid:%s] to cli0 msg. Description: This log indicates that update user dhcp-opt information to CLI. 501197 Send user role info: mac-[mac:%m], acl-[acl:%d]. Description: No description is available. 501198 Receive disconnect user, mac-[mac:%m], bssid-[bssid:%m], logout-[logout:%d], deauth-[deauth:%d], term-[trem:%d].
Table 22 User Debug Messages 74 | User Messages Message ID Message and Description 507008 Client Match: For client [mac:%m] Trigger [tr:%s] Better candidate [bss:%m] with signal -[sig:%d] dBm Channel [ch:%d] Current Signal -[cs:%d] dBm. Description: No description is available. 507009 Client Match: For client [mac:%m] No steering 5G in DFS non-occupancy. Description: No description is available. 507010 Client Match: For client [mac:%m] No steering Single radio AP.
Table 22 User Debug Messages Message ID Message and Description 524011 Src ip:[src:%s],Dst ip:[dst:%s],offset= [offset:%d] flags:=[flags:%d] Fragmented Packet. Description: This shows an internal user debug message 524012 Fragment Length [fraglen:%d]. Description: This shows an internal user debug message. 524013 Forwarding the Radius packet after stateful dot1x processing code=:[code:%d], smac=:[smac:%s],sport=:[sport:%d],dport[dport:%d]. Description: This shows an internal user debug message.
Table 22 User Debug Messages 76 | User Messages Message ID Message and Description 524039 [string:%s]: MFP sending Key Desc Ver 3 in key1. Description: This shows an internal user debug message. 524040 [string:%s]: rsn len ([len:%d]). Description: This shows an internal user debug message. 524041 [string:%s] :FT mesg3 copied gtk, len=[len:%d] data len=[len1:%d]. Description: This shows an internal user debug message.
Table 22 User Debug Messages Message ID Message and Description 524074 FT ([str:%s]): input pmk_r1_name =[str1:%s] Description: This shows an internal user debug message. 524075 FT ([str:%s]): snonce=[str1:%s] Description: This shows an internal user debug message. 524076 FT ([str:%s]): anonce=[str1:%s] Description: This shows an internal user debug message. 524077 FT ([str:%s]): Derived ptk [ptk:%s] Description: This shows an internal user debug message.
Table 22 User Debug Messages 78 | User Messages Message ID Message and Description 524092 [str:%s]: kcache found Description: This shows an internal user debug message. 524093 FT([str:%s]) r0kh:[r0kh:%s], r0_name:[str1:%s]. Description: This shows an internal user debug message. 524095 Missing kcache entry! Description: This shows an internal user debug messages. 524096 PMKR0-Name mismatch! cached=[str:%s] Description: This shows an internal user debug message.
Table 22 User Debug Messages Message ID Message and Description 524112 [func:%s]: kcache essid ([kcacheessid:%s]), essid ([essid:%s]) Description: This shows an internal user debug message. 524113 auth done called from ncfg_dot1x_validatepmkid_enabled Description: This shows an internal user debug message. 524114 MAC auth failed, skipping dot1x. Description: This shows an internal user debug message. 524115 Auth done called from Authenticated state.
Table 22 User Debug Messages 80 | User Messages Message ID Message and Description 541010 [func:%s]: apip-[ap_ip:%s], clientip-[client_ip:%s], mac-[mac:%m], [bssid:%m]. Description: AP sent reauth. 541011 [func:%s]: sta look up req to apip-[ap_ip:%s], mac-[mac:%m]. Description: AP sent/receive station request. 541014 [func:%s]: sta lkup response to apip-[ap_ip:%s], mac-[mac:%m]. Description: AP sent/receive station response. 541015 [func:%s]: Add mac auth token for sta-[sta:%m].
Table 22 User Debug Messages Message ID Message and Description 541037 [func:%s]: set accounting interval, sta [mac:%m] , account interval-[time:%d]. Description: Station update. 541038 [func:%s]: set class attribute, sta [mac:%m] , class attribute-[class:%s]. Description: Station update. 541039 [func:%s]: Set dhcp-opt, Station [mac:%m] essid [essid:%s] role [num:%d] rule_index [index:%x] vlan [vlan:%d] vlanhow[vlanhow:%s]. Description: Station dhcp-option update.
Table 22 User Debug Messages 82 | User Messages Message ID Message and Description 541060 [func:%s]: Send accounting ctx, client mac-[mac:%m], status-[status:%u], inocts[inocts:%u], outocts-[outocts:%u], inpkts-[inpkts:%u], outpkts-[outpkts:%u], sessid-[sessid:%s]. Description: AP update client from STM. 541061 [func:%s]: Set accounting ctx, client mac-[mac:%m], status-[status:%u], inocts[inocts:%u], outocts-[outocts:%u], inpkts-[inpkts:%u], outpkts-[outpkts:%u], sessid-[sessid:%s].
Chapter 5 Wireless Messages Error Messages Table 23 Wireless Error Messages Message ID Message and Description 400143 AP [name:%s]: ESSID mismatch index [ndx:%d]. expected [e1:%s] got [e2:%s] Description: An internal error has occurred. Recommended Action: Contact your support provider. 400144 AP [name:%s]: Station [sta:%m] not found while clearing association. Description: An internal error has occurred. Recommended Action: Contact Aruba Technical Support.
Table 24 Wireless Warning Messages Message ID Message and Description 400169 AP - [bssid:%m], max_clients [max_clients:%d] too big. Description: No description available. 400171 wifi_sap_down:unknown SAP IP [ip:%P] BSS [bssid:%m]. Description: No description available. 400172 wifi_load_balance:unknown SAP IP [ip:%P] BSS [bssid:%m]. Description: No description available. 400173 wifi_update_sta_vlan: AP [bssid:%m] not found. Description: No description available.
Table 24 Wireless Warning Messages Message ID Message and Description 404050 AM [bssid:%s]: ARM C [channel:%d] PER [per:%d] MER [mer:%d] FRR [frr:%d] [arm_error_rate_threshold:%d]-[arm_error_rate_wait_time:%d]. Description: No description available. 404052 AM [bssid:%s]: [message:%s]. Description: No description available. 404061 AM [bssid:%s]: ARM Band Request - GC [g_covered_channels:%d] AC [a_covered_channels:%d]. Description: No description available.
Table 24 Wireless Warning Messages Message ID Message and Description 404072 AM [bssid:%s]: ARM - too much power decreasing... cov-index [arm_ci:%d]/ [arm_nci:%d] tx-power [current_tx_power:%d] new_rra [current_channel:%d]/ [arm_max_tx_power:%d]. Description: No description available. 404073 AM [bssid:%s]: ARM - too little power increasing... cov-index [arm_ci:%d]/[arm_nci:%d] tx-power [current_tx_power:%d] new_rra [current_channel:%d]/ [arm_min_tx_power:%d]. Description: No description available.
Table 24 Wireless Warning Messages Message ID Message and Description 404092 AM [bssid:%s]: ARM HT Channel Band Trigger new [channel:%d]-[sec_channel:%d][arm_ii_arm_ccii:%d]/[arm_nii_arm_nccii:%d] old [ap_amc_channel:%d][ap_amc_channel_sec:%d]-[arm_ccii_arm_ii:%d]/[arm_nccii_arm_nii:%d] new_rra [min_amc_channel_pri:%d]-[min_amc_channel_sec:%d]/[new_tx_power:%d]. Description: No description available.
Table 24 Wireless Warning Messages Message ID Message and Description 404406 AM [bssid:%s]:SM: Unexpected channel [channel:%d] change by AM for Spectrum Monitor radio. Description: No description available. Notice Messages Table 25 Wireless Notice Message Message ID Message and Description 400102 AP [name:%s]: probe request: dropped entry in ip table for [ip:%P]. Description: No description available. 400160 AP [name:%s]: Starting to configure AP at [ap:%p]. Description: No description available.
Table 25 Wireless Notice Message Message ID Message and Description 404400 AM:SM: Spectrum: new Wi-Fi device found = [addr:%s] SSID = [ssid:%s] BSSID [bssid_str:%s] DEVICE ID [did:%d]. Description: This log indicates a new Wi-Fi device is detected by the spectrum radio. 404401 AM:SM: Spectrum: deleting Wi-Fi device = [addr:%s] SSID = [ssid:%s] BSSID [bssid_str:%s] DEVICE ID [did:%d]. Description: This log indicates a previously detected Wi-Fi device is being deleted due to inactivity.
Table 27 Wireless Debug Messages Message ID Message and Description 400132 AP [name:%s]: SAPCP Sending SAPCP Probe Response. Description: No description available. 400133 AP [name:%s]: SAPCP Probe from unknown bssid [bss:%m], dropping. Description: No description available. 400134 AP [name:%s]: SAPCP: Unknown sap. Description: No description available. 400162 AP [name:%s]: Registering AP, new virtual ap for ESSID [ess:%s], deny broadcast [db:%d]. Description: No description available.
Chapter 6 ARM Messages Error Messages Table 28 ARM Error Messages Message ID Message and Description 702002 [msg:%s]. Description: This log indicates that we encountered an internal system error. Recommended Action: Contact your support provider. 700102 [msg:%s] Description: No description is available. Warning Messages Table 29 ARM Warning Messages Message ID Message and Description 700100 [msg:%s] Description: No description is available.
| ARM Messages Dell Networking W-Series Instant Access Point 6.3.1.1-4.
