Concept Guide
Table Of Contents
- About this Guide
- About Instant
- Setting up a W-IAP
- Automatic Retrieval of Configuration
- Instant User Interface
- Initial Configuration Tasks
- Customizing W-IAP Settings
- Modifying the W-IAP Host Name
- Configuring Zone Settings on a W-IAP
- Specifying a Method for Obtaining IP Address
- Configuring External Antenna
- Configuring Radio Profiles for a W-IAP
- Configuring Uplink VLAN for a W-IAP
- Changing the W-IAP Installation Mode
- Changing USB Port Status
- Master Election and Virtual Controller
- Adding a W-IAP to the Network
- Removing a W-IAP from the Network
- VLAN Configuration
- IPv6 Support
- Wireless Network Profiles
- Configuring Wireless Network Profiles
- Configuring Fast Roaming for Wireless Clients
- Configuring Modulation Rates on a WLAN SSID
- Multi-User-MIMO
- Management Frame Protection
- Disabling Short Preamble for Wireless Client
- Editing Status of a WLAN SSID Profile
- Editing a WLAN SSID Profile
- Deleting a WLAN SSID Profile
- Wired Profiles
- Captive Portal for Guest Access
- Understanding Captive Portal
- Configuring a WLAN SSID for Guest Access
- Configuring Wired Profile for Guest Access
- Configuring Internal Captive Portal for Guest Network
- Configuring External Captive Portal for a Guest Network
- Configuring Facebook Login
- Configuring Guest Logon Role and Access Rules for Guest Users
- Configuring Captive Portal Roles for an SSID
- Configuring Walled Garden Access
- Authentication and User Management
- Managing W-IAP Users
- Supported Authentication Methods
- Supported EAP Authentication Frameworks
- Configuring Authentication Servers
- Understanding Encryption Types
- Configuring Authentication Survivability
- Configuring 802.1X Authentication for a Network Profile
- Enabling 802.1X Supplicant Support
- Configuring MAC Authentication for a Network Profile
- Configuring MAC Authentication with 802.1X Authentication
- Configuring MAC Authentication with Captive Portal Authentication
- Configuring WISPr Authentication
- Blacklisting Clients
- Uploading Certificates
- Roles and Policies
- DHCP Configuration
- Configuring Time-Based Services
- Dynamic DNS Registration
- VPN Configuration
- IAP-VPN Deployment
- Adaptive Radio Management
- Deep Packet Inspection and Application Visibility
- Voice and Video
- Services
- Configuring AirGroup
- Configuring a W-IAP for RTLS Support
- Configuring a W-IAP for Analytics and Location Engine Support
- Managing BLE Beacons
- Clarity Live
- Configuring OpenDNS Credentials
- Integrating a W-IAP with Palo Alto Networks Firewall
- Integrating a W-IAP with an XML API Interface
- CALEA Integration and Lawful Intercept Compliance
- Cluster Security
- W-IAP Management and Monitoring
- Uplink Configuration
- Intrusion Detection
- Mesh W-IAP Configuration
- Mobility and Client Management
- Spectrum Monitor
- W-IAP Maintenance
- Monitoring Devices and Logs
- Hotspot Profiles
- ClearPass Guest Setup
- IAP-VPN Deployment Scenarios
- Acronyms and Abbreviations
210 | DHCP Configuration Dell Networking W-Series Instant 6.5.1.0-4.3.1.0 | User Guide
You can configure distributed DHCP scopes such as Distributed, L2 or Distributed, L3 by using the Instant UI or
the CLI.
In the Instant UI
To configure distributed DHCP scopes such as Distributed, L2 or Distributed, L3:
1. Click More > DHCP Server. The DHCP Server window is displayed.
2. To configure a distributed DHCP mode, click New under Distributed DHCP Scopes. The New DHCP
Scope window is displayed. The following figure shows the contents of the New DHCP Scope window.
Figure 49 New DHCP Scope: Distributed DHCP Mode
3. Based on the type of distributed DHCP scope, configure the following parameters:
Parameter Description
Name Enter a name for the DHCP scope.
Type Select any of the following options:
l Distributed, L2—On selecting Distributed, L2, the VC acts as the DHCP server
but the default gateway is in the data center. Traffic is bridged into VPN tunnel.
l Distributed, L3—On selecting Distributed, L3, the VC acts as both DHCP
server and default gateway. Traffic is routed into the VPN tunnel.
VLAN Specify a VLANID. To use this subnet, ensure that the VLANID specified here is
assigned to an SSID profile. For more information on SSID profile configuration, see
Configuring VLAN Settings for a WLAN SSID Profile on page 83 and Configuring
VLAN for a Wired Profile on page 105.
Netmask If Distributed, L2 is selected for the type of DHCP scope, specify the subnet mask.
The subnet mask and the network determine the size of subnet.
Table 44: Distributed DHCP Mode Configuration Parameters