Concept Guide
82 | Wireless Network Profiles Dell Networking W-Series Instant 6.5.1.0-4.3.1.0 | User Guide
Parameter Description
individually for each W-IAP in the cluster.
SSID Encoding To encode the SSID, select UTF-8. By default, the SSIDs are not encoded.
NOTE: When a wireless SSIDis encoded, by default, UTF-8 is added to the access rules
that are active on the SSID. However this does not apply for the access rules that are
configured separately for the SSID. UTF-8 is not supported for wired networks.
Deny inter user
bridging
When enabled, the bridging traffic between two clients that are connected to the same
SSID on the same VLAN is disabled. The clients can connect to the Internet, but cannot
communicate with each other, and the bridging traffic between the clients is sent to the
upstream device to make the forwarding decision.
ESSID Enter the Extended Service Set Identifier (ESSID). If the value defined for ESSID value is not
the same as the profile name, the SSIDs can be searched based on the ESSID value and
not by its profile name.
Table 21: WLAN Configuration Parameters
5. Click Next to configure VLAN settings. For more information, see Configuring VLAN Settings for a WLAN
SSID Profile on page 83.
In the CLI
To configure WLAN settings for an SSID profile:
(Instant AP)(config)# wlan ssid-profile <name>
(Instant AP)(SSID Profile <name>)# essid <ESSID-name>
(Instant AP)(SSID Profile <name>)# type {<Employee>|<Voice>|<Guest>}
(Instant AP)(SSID Profile <name>)# broadcast-filter {All|ARP|Unicast-ARP-Only|Disabled}
(Instant AP)(SSID Profile <name>)# dtim-period <number-of-beacons>
(Instant AP)(SSID Profile <name>)# multicast-rate-optimization
(Instant AP)(SSID Profile <name>)# dynamic-multicast-optimization
(Instant AP)(SSID Profile <name>)# dmo-channel-utilization-threshold
(Instant AP)(SSID Profile <name>)# a-max-tx-rate <rate>
(Instant AP)(SSID Profile <name>)# a-min-tx-rate <rate>
(Instant AP)(SSID Profile <name>)# g-max-tx-rate <rate>
(Instant AP)(SSID Profile <name>)# g-min-tx-rate <rate>
(Instant AP)(SSID Profile <name>)# zone <zone>
(Instant AP)(SSID Profile <name>)# bandwidth-limit <limit>
(Instant AP)(SSID Profile <name>)# per-user-bandwidth-limit <limit>
(Instant AP)(SSID Profile <name>)# air-time-limit <limit>
(Instant AP)(SSID Profile <name>)# wmm-background-dscp <dscp>
(Instant AP)(SSID Profile <name>)# wmm-background-share <share>
(Instant AP)(SSID Profile <name>)# wmm-best-effort-dscp <dscp>
(Instant AP)(SSID Profile <name>)# wmm-best-effort-share <share>
(Instant AP)(SSID Profile <name>)# wmm-video-dscp <dscp>
(Instant AP)(SSID Profile <name>)# wmm-video-share <share>
(Instant AP)(SSID Profile <name>)# wmm-voice-dscp <dscp>
(Instant AP)(SSID Profile <name>)# wmm-voice-share <share>
(Instant AP)(SSID Profile <name>)# rf-band {<2.4>|<5>|<all>}
(Instant AP)(SSID Profile <name>)# content-filtering
(Instant AP)(SSID Profile <name>)# mfp-capable
(Instant AP)(SSID Profile <name>)# mfp-required
(Instant AP)(SSID Profile <name>)# hide-ssid
(Instant AP)(SSID Profile <name>)# out-of-service <def> <name>
(Instant AP)(SSID Profile <name>)# time-range <profile name> {<Enable>|<Disable>}
(Instant AP)(SSID Profile <name>)# inactivity-timeout <interval>
(Instant AP)(SSID Profile <name>)# local-probe-req-thresh <threshold>