Administrator Guide

Parameter Description
WirelessWaitEnet—This option species the wait period before the
wireless initializes in case of Enet Up. The default value is 5.
Device=vusb
[ForceRedirect=DeviceID]
[ForceLocal=DeviceID]
[Type={TCX, HDX}]
[InterfaceRedirect={no, yes}]
Device — Species the ID of a local USB device that is not redirected by
default.
ForceRedirect — Species a forced redirect of the local USB device to
the server. This parameter has priority over ForceLocal.
The DeviceID can be found in the event log. For example, if you nd “TCX
USB: Local Device(0x04f2,0x0112,0x03,0x01,0x01)”, set the parameter as:
Device=vusb
ForceRedirect=0x04f2,0x0112,0x03,0x01,0x01
Type — (Citrix Environments Only) In Citrix environments, allows you to
force the usage of HDX for USB virtualization instead of TCX. For
example: Device=vusb Type=HDX
NOTE: To use the TCX option, TCX Suite must be install on the
target server.
InterfaceRedirect— Default is no. Yes/no option to enable part of a
composite device to run locally and part of the device to run on a remote
session.
Device=Wireless
[Mode={Infrastructure, AdHoc}]
[SSID=ssid Channel={1-14}]
[WepKey={None, 1-4}]
[Key1=<k1>]
[Key2=<k2>]
[Key3=<k3>]
[Key4=<k4>]
[Key1Enc=<key1 encrypted>]
[Key2Enc=<key2 encrypted>]
[Key3Enc=<key3 encrypted>]
[Key4Enc=<key4 encrypted>]
[RoamSensitive={high, medium, low}]
[Algorithm={Open, SharedKey}]
[DisableBand={None, 2.4G, 5G}]
[PreferBand={None, 2.4G, 5G}]
[Priority=ssid_list]
[DisableN={yes,no}]
[DisableWlan={yes, no, EnetUp}
Device
— Denes the wireless Ethernet device remotely and saves to the
local NVRAM. Not all options are needed. For example, you can dene
Key1 to have a key of “k1” and leave out Key2 through Key4.
WEPKey — Default is None. k1 to k4 are any real values of 5 to 13
characters or 10 to 26 Hex digits. Encrypted keys will overwrite
unencrypted keys. Thus, if Key1 and Key1Enc are both congured, then
Key1Enc will overwrite Key1. RoamSensitive — denes the sensitivity
level of wireless roaming with respect to launching the Roaming daemon:
high - signal lower than -60 dBm
medium - signal lower than -70 dBm
low - signal lower than -80dBm
The RoamSensitive parameter is also used to enable wireless roaming. If it
is not congured in the INI le, roaming will never be launched even if the
signal is lower than -80dbm, unless it totally loses a wireless signal.
Algorithm — species the authentication method of WEP between your
zero client and the access point. If set to Open, open authentication will
be selected. If set to ShareKey, shared key authentication will be selected.
Algorithm=open wepkey={1,2,3,4} means open along with wep for
wireless connection(Access typein GUI is displayed as Open(WEP)), while
Algorithm=open wepkey=none means open.(Access type in GUI is
displayed as Open)
DisableBand — Default is None. Used to disable 2.4G or 5G 802.11 band.
Preferband—Default is none Used to set the prioprity of wireless
connection band, and select the 2.4G or 5G access point to connect.
Priority — sets the priority of wireless proles. The ssid list is separated
by a semicolon or comma and the priority is from high to low.
DisableN Used to disable 802.11n mode, and it is enabled by default.
Creating and Using xen.ini Files
189