Administrator Guide
Table Of Contents
- Dell Wyse ThinOS Lite Release 2.6 Administrator’s Guide
- Introduction
- Before working on ThinOS Lite
- Getting started
- Global connection settings
- Configuring the connectivity
- Configuring the network settings
- Configuring the remote connections
- Configuring the Citrix broker setup
- Configuring the visual settings
- Configuring the general options
- Configuring the authentication settings
- Configuring the central configurations
- Configuring the VPN manager
- Configuring the connection broker
- Configuring Citrix
- Configuring the Citrix broker setup
- Citrix HDX RealTime Multimedia Engine—RTME
- Citrix Icon refresh
- Using multiple audio in Citrix session
- Using Citrix NetScaler with CensorNet MFA authentication
- Okta Integration through Citrix NetScaler
- Configuring ICA connections
- ICA Self Service Password Reset—SSPR
- QUMU or ICA Multimedia URL Redirection
- HTML5 Video Redirection
- ICA SuperCodec
- Anonymous logon
- Configuring the Citrix UPD Printer
- Introduction to Flash Redirection
- Configuring Citrix
- Configuring Zero Client Settings
- Performing Diagnostics
- BIOS Management
- Security Changes
- Creating and Using xen.ini Files
- Examples of Common Printing Configurations
- Important Notes
- Troubleshooting
Enter the address of the router that connects the thin client to the internet. The address must exist on the same
subnet as the thin client as defined by the IP address and the subnet mask. If DHCP is used, the address can be
supplied through DHCP.
c. Select the IPV6 check box, and then click Advanced to select various IPV6 supported setting options from the available
check boxes.
The following check boxes are displayed in the IPv6 Advanced Settings dialog box:
● Allow IPv4 to be disabled when IPv6 is enabled
● Prefer IPv4 over IPv6 when both are available
● Disable Stateless Address Auto configuration (SLAAC)
● Disable Duplicate Address Detection (DAD)
● Disable ICMPv6 Echo Reply
● Disable ICMPv6 Redirect Support
● Use Standard DHCPv6 Timers
Click properties and use the following guidelines:
● Wait DHCP — Selecting this option enables your thin client to wait for IPV6 DHCP before the sign-in, if not selected
the system will only wait for IPV4 DHCP if enabled.
● Dynamically allocated over DHCP/BOOTP — Selecting this option enables your thin client to automatically
receive information from the DHCP server. The network administrator must configure the DHCP server (using DHCP
options) to provide information. Any value provided by the DHCP server replaces any value entered locally on the
Options tab, however, locally entered values are used if the DHCP server fails to provide replacement values.
● Statically specified IP Address — Select this option to manually enter the IP Address, Subnet Mask and Default
Gateway.
○ IP Address — Must be a valid network address in the server environment. The network administrator must
provide this information.
○ Subnet Mask — Enter the value of the subnet mask. For more information, see various options supported by
IPV4 in this section.
○ Default Gateway — Use of gateways is optional. For more information, see various options supported by IPV4 in
this section.
● DNS Servers — Use of DNS is optional. DNS allows you to specify remote systems by their host names rather than
IP addresses. If a specific IP address (instead of a name) is entered for a connection, it rather than DNS is used to
make the connection. Enter the network address of an available DNS Server. The value for this box may be supplied
by a DHCP server. If the DHCP server supplies this value, it replaces any locally configured value. If the DHCP server
does not supply this value, the locally configured value is used.
d. Select the check box to enable IEEE802.1x authentication.
EAP Type — If you have enabled the Enable IEEEE 802.1x authentication check box, select the EAP Type option you
want (TLS, LEAP, PEAP or FAST).
● TLS — If you select the TLS option, click Properties to open and configure the Authentication Properties dialog
box.
○ Select the Validate Server Certificate check box because it is mandatory to validate your server certificate.
NOTE:
The CA certificate must be installed on the thin client. Also note that the server certificate text field supports
a maximum of approximately 255 characters, and supports multiple server names.
○ If you select the Connect to these servers check box, the box is enabled where you can enter the IP address of
server.
○ Click Browse to find and select the Client Certificate file and Private Key file you want.
NOTE: Make sure you select PFX file only.
○ From the Authenticate drop-down list, select either User Authentication or Machine Authentication based on
your choice.
32
Configuring the connectivity