Setup Guide

[wpapskpwdEnc={passphrase encrypted for WPA-PSK}]
[wpa2pskpwd={passphrase for WPA2-PSK}]
[wpa2pskpwdEnc={passphrase encrypted for WPA2-PSK}]
[encryption={TKIP|CCMP}]
[fasteap={EAP-MSCHAPV2, EAP-GTC}]
[fastidentity={Identity for EAP_FAST}]
[fastmschapun={username for EAP-FAST/EAP-MSCHAPV2}]
[fastpmschappwd={password for EAP-FAST/EAP-MSCHAPV2}]
[fastmschappwdEnc={password encrypted for EAP-FAST/EAP-
MSCHAPV2}]
[fastmschapdm={domain for EAP-FAST/EAP-MSCHAPV2}]
[fastmschaphidedm={yes,no}]
[fastsinglesignon={yes, no}]
[fastgtcun={username for EAP-FAST/EAP-GTC}]
[fastgtcpwd={password for EAP-FAST/EAP-GTC}]
[fastgtcpwdEnc={password for encrypted for EAP-FAST/EAP-
GTC}]
Example: IEEE8021X=yes network=wireless access=wpa-ent
eap=yes eaptype=eap-tls tlsclntcert=user.cer
tlsclntprikey=user.pfx tlsclntprikeypwd=12345678
OR
IEEE8021X=yes network=wireless access=wpa-ent eap=yes
eaptype=eap-tls tlsclntcert=user.cer tlsclntprikey=user.pfx
tlsclntprikeypwd=12345678 leapun=user1 password=1234
peapmschapun=user1 peapmschappwd=12345
peapmschapdm=wyse.com
IEEE8021X=yes network=wired eap=yes eaptype=eap-tls
tlsclntcert=user.cer tlsclntprikey=user.pfx
tlsclntprikeypwd=12345678
By default, peapidentity is same as peapmschapun.If
peapmschaphidedm is set to yes, the domain will use saved
peap MSCHAP domain name and the prompts dialog will not
include the domain eld when you perform ieee8021x
authentication.
The following example describes wildcard server validation:
IEEE8021X=yes network=WIRED access=WPA2-ENT
servervalidate=yes eap=yes eaptype=EAP-PEAP
servercheck=yes servername=w2k8-
ACS-64.sqawirelsess.com peapmschapdm=EAP-MSCHAPV2
peapgtcun=sqawirless2 peapmschappwd=123!@#qwe
The username of ieee8021x (fastmschapun, peapmschapun,
peapgtcun, leapun) can be congured as system variables like
$mac, $sn etc. By default, fastidentity is same as
fastmschapun.
If fastmschaphidedm is set to yes, the domain uses saved
EAP_FAST MSCHAP domain name, and the prompts dialog
does not include the domain eld when you perform ieee8021x
authentication.
The following example describes wildcard server
validation:IEEE8021X=yes network=WIRED access=WPA2-
ENT servervalidate=yes eap=yes eaptype=EAP-FAST
servercheck=yes servername=w2k8-
ACS-64.sqawirelsess.com fastmschapdm=EAP-MSCHAPV2
fastgtcun=sqawirless2 fastmschappwd=123!@#qwe
**Inactive={
0, to 480} (minutes)
[NoSessionTimer=0-480]
Default is 0.
Species that if there is no keyboard or mouse use in the
congured time in minutes, it will sign o or shutdown or reboot
depending on AutoSigno= …
If NoSessionTimer is set, then when there is an active sessions, use
this timer to replace the Inactive value.
The following controls whether to reboot or shutdown or sign o.
AutoSignoff=yes [Shutdown=yes] [Reboot=yes]
IPProto=ICMP
[DisableTStamp={yes, no}]
[DisableEcho={yes, no}]
Congures the ICMP protocol.
DisableTStamp — If DisableTStamp=yes, the system will not
reect the ICMP timestamp (13) request.
Parameters for wnos INI, {username} INI, and $MAC INI les 75