Deployment Guide

Table 6. Connection Settings: wnos.ini files only (continued)
Parameter Description
reboot — After 5 seconds, the system reboots.
shutdown — After 5 seconds, the system shuts down.
DHCPOptionsRemap={no, yes}
[DisableOption12={no, yes}]
[FileServer={128 to 254}]
[RootPath={128 to 254}]
[FtpUserName={128 to 254}]
[FtpPassWord={128 to 254}]
[RapportServer={128-254}]
[RapportPort={128-254}]
[WDMServer={128 to 254}]
[WDMPort={128 to 254}]
[PnliteServer={128 to 254}]
[DomainList={128 to 254}]
[VDIBroker-{248 to 254}]
[RapportSecurePort={128-254}]
[Discover={
yes, no}]
[WDMSecurePort={128 to 254}]
[WDMFQDN={128-254}]
[CCMGroupKey={128-254}]
[CCMServer={128-254}]
[CCMMQTTServer={128-254}]
[CCMCAValidation={128-254}]
Default is no.
DHCPOptionsRemap — Specifies whether or not the
following options can be set.
The value for each option must be from 128 to 254. Values
for the options must be different for each option. These
options are used to configure DHCP server tags for thin client
booting.
The option DisableOption12 sets if the option tag 12 in DHCP
is accepted or not. As default, DHCP option 12 sets the
hostname and domain name of the terminal. For example,
the information of option 12 is terminal name.wyse.com, the
terminal name will be set as terminalname and the domain
name will be set as wyse.com.
If you set different value for DisableOption12 from the value
in NVRAM, the system will automatically reboot to make the
value valid. (CIR36891)
RapportSecurePort— Specifies the HTTPS port of WDM
server. It is in 6.3 to support WDM4.7.
Discover—If Discover=yes, the device fetches Wyse DHCP
options from DHCP server, otherwise, it prevents the device
from fetching those information. Default value is yes. If the
device receives FileServer/WDMServer information through
the DHCP server, then the associate User interface is
protected.
NOTE:
WDMSecurePort is the specified HTTPS port of the WDM
server.
WDMServer—Value 186 specifies the IP address of WDM
server. Value 192 specifies the HTTP port of WDM server.
WDMSecurePort—Specifies the HTTPS port of WDM
server.
WDMFQDN — Specifies the Fully Qualified Domain Name
(FQDN) of the WDM server.
NOTE:
The CCMGroupKey, CCMServer,
CCMMQTTServer and CCMCAValidation options are
specified to remap the tags for CCM configuration.
DHCPUserClassID=class_id
[ParseVendorInfo={no, yes}]
DHCPUserClassID — Specifies the UserClassID used for
DHCP.
ParseVendorInfo — Default is yes. Yes/no option to specify
whether or not ThinOS will interpret DHCP option 43.
This is a vendor-specific information. If ParseVendorInfo is set
to no and the DHCPVendorID is also used with this parameter,
you must set ParseVendorInfo=yes and then reboot the thin
client twice. Maximum of 26 characters are allowed in a string.
DHCPVendorID=vendor
[ParseVendorInfo={no, yes}]
DHCPVendorID — Specifies the VendorID used for DHCP.
ParseVendorInfo — Default is yes. Yes/no option to specify
whether or not ThinOS will interpret DHCP option 43.
22 Parameters for wnos INI files only