Release Notes

– 3840 x 2160
Dual 3840 x 2160 resolution is supported with the Dual Display ports for 30 Hz display refresh rate.
The following are the tested Dell monitors supporting dual 3840 x 2160 resolution:
– Dell P2815Q (3840 x 2160)
– Dell UP3216Q (3840 x 2160)
• Package versions—The following are the recommended/optional packages:
– RTME.i386.pkg version 1.15
– FR.i386.pkg version 1.13
– TCX.i386.pkg version 1.09
INI parameters
The ThinOS v8.3.1 release contains the following newly added INI parameters:
Table 25. INI parameters
Parameter Description
SessionCong=ICA
[desktopmode={fullscreen, window}]
[mapdisksunderz={yes, no, A-Z, a-z, A:-Z:, a:-
z:}]
[DiskMapTo=a sequence of characters]
[SysMenu={remote|local}]
[SessionReliability={yes,no}]
[WarnPopup={yes, no}]
[ondesktop={yes,no, all, none, desktops,
applications}]
[AudioQuality={default,high,medium,low}]
[USBRedirection={TCX, ICA | HDX}]
[ZLKeyboardMode={0, 1, 2}]
[ZLMouseMode={0, 1, 2}]
[Timeout={Yes, No}]
[SucConnTimeout=seconds]
[HDXFlashUseFlashRemoting={Never,Always
}]
[HDXFlashEnableServerSideContentFetching
={Disabled,Enabled}]
[EnableRTME={Yes,No}]
[FlipByTimer={0, 1}]
[RefreshTimeOut={dd:hh:mm}]
[PasswordExpireNotify={Yes, No}]
Set
SessionCong=ICA to establish the default settings for ICA sessions.
The option desktopmode can specify the display mode of ICA published desktop when
you use ICA PNAgent logon. The default is fullscreen mode for PNA desktop application.
NOTE: Only if mapdisks=yes, the mapdisksunderz=yes takes
eect.
MapdisksUnderZ option can specify a driver letter to replace default driver letter Z. For
example, if MapdisksUnderZ=X, all the disks are under the drive X instead of drive Z
(CIR54875). A sequence of characters is used by DiskMapTo, such as RTNM, where each
letter is mapped to each disk. For example, R is mapped to rst disk (in ThinOS, it is D:/),
and T is second letter mapped to second disk (in ThinOS, it is E:/). Only a - y and A – Y
characters are accepted, and all lower characters are changed to upper. Any other
characters are skipped. Also, duplicate characters are omitted. For example,
#GGefZzedAF1JaE is mapped to GEFDAJ. The number of disks mapped to Session
depends on the number of valid letters provided. If no letter is provided, all disks are
mapped to session with default driver letters.
The option SysMenu can specify the sys menu mode when you right-click on the taskbar
button of seamless window. If it is remote, the sys menu comes from remote server,
otherwise it is from local. The default is local sys menu. (CIR37219).
The option SessionReliability=yes can enable session reliability. (CIR40218).
The option WarnPopup=no can disable the warning message when session reliability
happens to decrease the administrative support calls.
The option ondesktop=yes can show all PNA/PNLite applications on the desktop
(CIR41291). Since 7.0.0_31, there is a new logic for the ondesktop parameter. (CIR53288)
• If AutoConnectList is set in the PNLiteServer statement, all connections congured in
the AutoConnectList parameter shows.
• The default value of the ondesktop parameter is no. It means that the property of
ondesktop is controlled by the server. But the connections are always added into
connection manager list and PNA menu list.
• In the other cases except if the parameter is no, the connection is controlled by local.
If it does not display on desktop, it is not needed to add into connection manager list
and PNA menu list.
– all - same as yes, shows all parameters on desktop
– none – does not show any
Release version 8.3.1
21