Dell Wyse Management Suite Version 1.0 Administrator’s Guide November 2018 Rev.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents Chapter 1: Introduction to Wyse Management Suite...................................................................... 7 Chapter 2: Getting started with Wyse Management Suite............................................................. 8 Logging in to Wyse Management Suite on public cloud............................................................................................ 8 Getting started with Wyse Management Suite on private cloud............................................................
Security.......................................................................................................................................................................... 70 Configuring central configuration settings.............................................................................................................71 Other settings...............................................................................................................................................................
Pulling log file.....................................................................................................................................................................116 Renaming thin client........................................................................................................................................................ 117 Chapter 6: Apps and data...........................................................................................................
License subscription..................................................................................................................................................143 System setup.................................................................................................................................................................... 143 Appendix A: Installing or upgrading Wyse Device Agent.............................................................
1 Introduction to Wyse Management Suite Wyse Management Suite is the next generation management solution that enables you to centrally configure, monitor, manage, and optimize your Dell Wyse thin clients. It also offers advanced feature options such as cloud as well as on-premises deployment, manage-from-anywhere option by using a mobile application, enhanced security such as BIOS configuration and port lockdown.
2 Getting started with Wyse Management Suite Topics: • • • • • Logging in to Wyse Management Suite on public cloud Getting started with Wyse Management Suite on private cloud Prerequisites to deploy Wyse Management Suite on private cloud Functional areas of management console Configuring and managing thin clients Logging in to Wyse Management Suite on public cloud To log in to the Wyse Management Suite console, you must have a supported web browser installed on your system.
Getting started with Wyse Management Suite on private cloud Prerequisites to deploy Wyse Management Suite on private cloud Table 1.
Functional areas of management console The Wyse Management Suite console is organized into the following functional areas: About this task ● The Dashboard page provides information about each functional area of the system. ● The Groups page employs a hierarchical group policy management for device configuration. Optionally, subgroups of the global group policy can be created to categorize devices according to corporate standards.
Wyse Management Suite supports standard and advanced application policies. A standard application policy allows you to install a single application package. You need to reboot the device before and after each application installation. With an advanced application policy, multiple application packages can be installed with only two reboots. This feature is available only in the Pro edition.
3 Wyse Management Suite dashboard The Dashboard page enables you to view the status of a system, and the recent tasks that are performed within the system. To view a particular alert, click the link in the Alerts section. The Dashboard page also allows you to view the device summary. Figure 1. Dashboard Dashboard page includes the following links: ● Alerts—Displays the summary of all the alerts. You can navigate to the functional areas of the system that requires your attention.
4 Managing groups and configurations Prerequisites The Groups & Configs page enables you to define policies that are required to configure your devices. You can create sub groups of the global group policy and categorize devices based on your requirements. For example, devices may be grouped based on job functions, device type, and so on. About this task Figure 2.
After you configure the policy settings, thin clients are notified about the changes. Changes take effect immediately after configuring the thin clients. NOTE: Certain settings, such as BIOS configuration for Windows Embedded Standard require a restart for the changes to take effect. However, most of the settings on ThinLinux and ThinOS, you must restart the device for changes to take effect.
Steps 1. In the Devices page, click the device you want to configure. The Device Details page is displayed. 2. Click the Summary tab. 3. In the Device Configuration section, click Create/Edit Exceptions. Group tree hierarchy Group tree hierarchy consists of the following options: ● Add Group ● Edit Group ● Remove Group Adding a group About this task To add a group, do the following: Steps 1. On the Groups & Configs page, in Group Tree Hierarchy, click the + icon. 2.
Steps 1. In the Groups page, under Group Tree Hierarchy, click the Remove Group icon. A warning message indicating that this action removes one or more groups from the group tree hierarchy is displayed. NOTE: When you remove a group from the group hierarchy, all users and devices that belong to the deleted group are moved to a selected target group. 2. Click Remove Group. Unmanaged group Devices that belong to the unmanaged group do not use licenses or receive configuration or application-based policies.
ThinOS—Wizard mode Use this page to configure the most frequently used parameters for the ThinOS devices. To configure the policy settings, do the following: 1. Select Wizard as the mode of configuration. 2. The following are the available policy settings on the ThinOS—Wizard mode page. Figure 4. ThinOS—Wizard mode ● ● ● ● ● ● Setup Security ● Setup Keyboard and Display ● Setup Visual Experience ● Setup Timezone ● Setup General Settings ● Setup Broker Click Next to go to policy settings.
Table 2. Configuring Privilege Settings (continued) Option Description ● Low—All settings are enabled on the local client. Show Display Settings (8.5+) Select this option to configure the display settings. From the drop-down menu, select a group to set the configuration access. Enable Keyboard and Mouse Settings (8.5+) Select this option to configure the keyboard and mouse settings. Enable Admin mode Select this option to access the admin mode by entering the user name and password.
Visual experience Use this page to configure the thin client visual experience settings, such as desktop display (Classic or Zero Launchpad) and session functionality. Table 5. Visual experience Parameter Description Classic Desktop vs Zero Launchpad Allows you to define the desktop experience. NOTE: Zero Launchpad is recommended for ThinOS Lite/Xenith devices, and for full screen sessions. Classic Desktop is recommended for seamless applications.
Configuring timezone Use this page to configure the thin client settings, such as time servers, and time zone. Table 6. Timezone Option Description Manually Set Time Zone Select this option to override the system preference menu of the device with the time zone settings. Date Format (8.5+) Select the required date format. Time Format (8.5+) Select the required time format. Time Servers Enter the list of time servers to synchronize local time separated by a semicolon.
Configuring broker settings Use this page to configure the thin client remote connection and broker settings, such as addresses and credentials for brokers, such as, Citrix, Microsoft, VMware, and vWorkspace. Table 10. Configuring broker server Option Description Select the broker you are using Select this option to establish a broker connection for a published desktop.
Figure 5. ThinOS—Advanced mode ● Device Configuration ● Advanced Device Configuration ● Remote Connection (Legacy) ● Remote Connection (8.5+) ● Printers (8.5+) ● Network Settings (8.5+) 3. Click Save & Publish to save your changes. 4. Click Remove Policy to go back to the ThinOS page. 5. Click Cancel to go back to the Groups & Configs page. Configuring general settings—ThinOS 8.
Table 13. Configuring mirror file server Option Description Mirror File Server If the FileServer is offline, this setting allows you to store a local copy of the configuration in cache. Table 14. Configuring terminal settings Option Description Terminal Name Enter the terminal name. You can also use the system variables to automate renaming multiple devices. Terminal Reboot If this setting is enabled, the system is forced to restart after the terminal name is changed.
Table 16. Configuring timezone settings Option Description Manually Set TimeZone Select the check box to override the system preference menu settings. From the Timezone and Enable Daylight Savings drop-down menu, select your preferred option. Date Format (8.5+) From the Date Format (8.5+) drop-down menu, select the appropriate format. Time Format (8.5+) From the Time Format (8.5+) drop-down menu, select the appropriate format.
Table 19. Configuring administrator mode (continued) Option Description Encrypted Credentials (8.5+) Select the check box to encrypt the credentials. Show Admin Mode button (8.5+) Select the check box to display the admin mode option on the sign on window. Table 20. Configuring general settings Option Description Enable the Gkey reset Select this option to reset the factory settings of the device. While restarting the system, press the G key to reset the factory settings.
Table 22. Configuring VNC settings (continued) Option Description Prompt user on start Select this option to perform the shadowing process on the terminal. Query user timeout Enter the total amount of time in seconds to accept or reject the shadowing session. The range is 10–600 seconds. Promt user on end Select the check box to notify the end of a remote shadowing session. View only Select the check box to disable the keyboard or mouse events on the system during a shadowing session.
Table 24. Configuring keyboard settings (continued) Option Description Alt-Tab Press the Alt-Tab keys to lock the system. Display Use this page to configure the thin client monitor display settings, such as resolution, rotation, color depth, and dual monitor. Table 25. Display Parameter Description Monitor Resolution Allows you to set the resolution for your monitor. From the drop-down menu, select the appropriate resolution for your monitor.
Table 27. Configuring visual experience (continued) Option Description Disable Home Icon Select this option to disable the home icon. Enable Logon Main Menu (8.5+) Select the check box to enable the main menu screen on the desktop when you log in to the system.
Configuring device information Use the Device Info page to set the device details. Table 29. Configuring device information Option Description Location Enter the device location. Contact Enter the device contact. Custom 1 to 3 Enter the custom values. Configuring BIOS settings—ThinOS Use this page to configure the BIOS settings of ThinOS thin clients. Table 30. System configuration Option Description Enable Audio Select this check box to enable the audio device. Table 31.
Table 34. Configuring USB (continued) Option Description NOTE: The USB keyboard and the mouse always work in the BIOS setup irrespective of this setting. Enable USB Boot Support Select this check box to enable the USB boot setup. Allows you to boot any type of USB mass storage devices. Table 35. Configuring power management settings Option Description AC Recovery From the drop-down list, select an option to specify how the system must behave when the AC power is restored.
Table 37. Configuring firmware upgrade (continued) Option Description NOTE: Dell recommends that you enable this option if you define a firmware on the management console. It leads to an endless restart as the thin client applies differing images, if you have firmware policies in the management console and firmware on a local file server. Verify Signature Select the check box to verify the signature. Enable BIOS Upgrade Select this option to enable the BIOS upgrade process.
Configuring advanced settings—ThinOS Use this page to configure additional settings which are thin client specific INI parameters or to disable the local INI check. Dell recommends that you do not include the INI parameters for policies which are already configured in other options. Password encoding and encryption are not applied to password parameters. Table 40. Configuring advanced settings Option Description No Global INI If selected, the global INI parameter from the file server is not downloaded.
Table 41. Configuring connection broker settings (continued) Option Description Security Mode Select this option to set a security mode. This option is applicable only for VMware. Protocol Select this option to choose a protocol. This option is applicable only for VMware. Table 42. Configuring Direct connections (RDP) Option Description Connection Name Enter the name of the connection. Host Name or IP Address Enter the host name or IP address of the connection.
Table 43. Session behavior defaults (continued) Option Description USB Redirection Technology Select this option to enable USB redirection. USB redirection is a technology that Select this option to access the USB devices that are connected to the thin client from within a remote desktop or application. This option is applicable only for Citrix. Audio quality Select this option to set the audio quality. This option is applicable only for Citrix.
Table 45. Configuring peripheral behavior (continued) Option Description NOTE: You also have an option to exclude disk, printer, audio, and video devices. Mouse Queue timer Select this option to set the mouse queue timer in an ICA or RDP session. The range of the mouse queue timer is 0–99. Table 46. Configuring additional settings Option Description Maximum Bitmap Cache To set the maximum bitmap cache for your RDP session, enter a number from 128 to 1024.
Table 47. Configuring local resources settings (continued) Option Description Disks Read Only Select this option to enable read only disks. Enable USB Redirection Select this option to redirect the USB drives to the remote session. From the drop-down menu, select your preferred option. If Exclude some devices option is selected, you can exclude the following devices from the session: ● Exclude disk devices ● Exclude audio devices ● Exclude printer devices ● Exclude video devices Table 48.
Configuring third party authentication settings—ThinOS 8.5+ Use this page to configure Single Sign-On (SSO) authentication settings. Table 50. Configuring authentication settings Option Description Authentication Mode Select this option to specify the authentication mode. From the drop-down menu, select any one of the following options: ● Imprivata ● Caradiam ● SecureMatrix ● HealthCast Table 51.
Table 52. Configuring imprivata settings (continued) Option Description Disable Prompt To Enroll Select this option to disable the prompt to enroll option. If disabled, then ThinOS system does not prompt to enroll their security answers after OneSign sign on. Security Mode From the drop-down menu, select your preferred option. The security mode species the SSL certification validation policy. Table 53.
Table 55. Configuring HealthCast settings (continued) Option Description Client Certificate From the drop-down menu, select your preferred option. The certificates are uploaded to the file repository. Configuring citrix broker connection settings—ThinOS 8.5+ Use this page to configure the citric broker connection settings. Table 56. Configuring basic settings Option Description Broker Server Enter the broker server host name or IP address.
Table 58. Configuring multi logon settings (continued) Option Description Sequential Domain Select this option to choose the domains in sequential order which are listed in the DomainList option. Configuring citrix HDX connection settings—ThinOS 8.5+ Use this page to define VDI global settings for citrix connections. Table 59. Configuring basic settings Option Description Audio quality Select this option to set the audio quality. Enable Seamless Mode Select this option to set the seamless mode.
Table 61. Configuring basic settings (continued) Option Description NOTE: You must specify between HTTP:// or HTTPS://. Security Mode Select this option to set a security mode. Protocol Select this option to specify the display protocol. The server default protocols are All, RDP, PCoIP or Blast. Sessions to connect automatically Select this option to automatically connect to the session. NOTE: The name of the desktop or application is case sensitive.
Configuring Microsoft RDP connection settings—ThinOS 8.5+ Use this page to configure the Microsoft RDP connection settings. Table 64. Configuring basic settings Option Description Enable NLA Select this option to enable Network Level Authentication. User authentication is required to establish a connection with the server. Enable Recording Select this option to enable recording. Table 65.
Configuring vWorksapce broker connection settings—ThinOS 8.5+ Use this page to configure the vWorksapce broker connection settings. Table 67. Configuring basic settings Option Description Broker Server Enter the broker server host name or IP address. NOTE: You must specify between HTTP:// or HTTPS://. Enable vWorkspace Gateway Select this option to enable vWorkspace gateway functionality. Sessions to connect automatically Select this option to automatically connect to the session.
Table 69. Configuring basic settings (continued) Option Description Auto Start Select this option to restart the connection automatically. Reconnect After Disconnect Select this option to reconnect the connection automatically after the connection is disconnected. Table 70. Configuring local resources Option Description Map Printers Select this option to automatically connect the local printers when the session starts.
Table 73. Configuring terminal gateway settings Option Description Use Terminal Server Gateway Select this option to specify the Windows terminal server login details. If enabled, enter the following details: ● RD host name or IP address ● RD user name ● RD password ● RD domain name Configuring direct ICA connection settings—ThinOS 8.5+ Use this page to configure the ICA connections which can be accessed on the thin client. Table 74.
Table 76. Configuring local resources (continued) Option Description Map SmartCards Select this option to redirect the smartcards to the remote session. Table 77. Configuring logon settings Option Description Logon Mode Select this option to select the log in mode. Start Command Application Enter the start command application. Start Command Working Directory Enter the start command working directory. Table 78.
Table 80. Configuring printer select (continued) Option Description ● Local printer ● LPD printer ● SMB printer Local Printer From the drop-down menu select the local printer connection. Table 81. Configuring printer settings Option Description Name Enter the name of the shared printer. LocalName This option is applicable only for LPD printer. Enter the name of the printer. Host This option is applicable only for local LPD printer. Enter the IP address of the LPD service host.
Table 82. Configuring WLAN global settings (continued) Option Description The Prefer Band configuration is used to set the priority of wireless connection band, and to select the 2.4G or 5G access point to connect. The default value is Do not prefer any band. DisableN Select the check box to disable the 802.11n mode. Disable WLAN Select this option to disable the wireless functionality. From the drop-down menu, select the preferred option.
Table 85. Configuring IEEE 802.1X settings for WPA-Enterprise and WPA2-Enterprise (continued) Option Description LEAP user name This option is applicable only for EAP-LEAP. Enter the leap user name in the provided field. LEAP Password This option is applicable only for EAP-LEAP. Enter the leap password in the provided field. Server Validate This option is applicable only for EAP-TLS and EAP-PEAP. Select the check box to validate the sever connection.
Figure 6.
Table 86. Configuring display options (continued) Option Description Monitor Resolution (Primary) Select this option to set the resolution for your monitor. From the drop-down menu, select the appropriate resolution that suits your monitor type. Display Identifier (Primary) Select this option to set a display identifier for your monitor. From the drop-down menu, select an appropriate monitor identification number. Monitor Rotation (Primary) Select this option to set an orientation for your monitor.
Table 88. Configuring mouse and mouse pointer options (continued) Option Description Click Lock Select this option to highlight or drag function without holding down the mouse button. To set the Click Lock Time parameter, from the drop-down menu, select the appropriate time for the mouse button to be held down before the click is locked. Double Click Speed Select this option to set the time interval between two consecutive mouse clicks. From the drop-down menu, select your preferred option.
Configuring desktop experience Use this page to configure the thin client settings, such as desktop wallpaper, and desktop color for Windows Embedded Standard devices. Table 91. Configuring desktop experience Option Description Desktop Wallpaper Select this option to set a wallpaper for your desktop. After you enable the desktop wallpaper option, do the following: ● From the Wallpaper File drop-down list, select a wallpaper for your desktop.
Table 93. Configuring security and lockdown settings (continued) Option Description Disable USB Storage Device Access Select this option to enable or disable the USB mass storage device access for non-admin users. Disable Print Screen Select this option to enable or disable the print screen functionality for non-admin users. Disable Task Manager Select this option to enable or disable the task manager access for non-admin users.
Table 97. Configuring power settings when plugged-in (continued) Option Description Dim Display Select this option to set the time after which the display is dimmed. From the drop-down menu, select a delay time. Turn Off Display Select this option to set the time after which the display is turned off. From the drop-down menu, select a delay time. Table 98. Configuring shared drives Option Description Shared Drive Select this option to add a shared drive to your device. Click Add Shared Drive.
Table 100. Basic options (continued) Option Description Username Select this option to define a user name for the Citrix connection, if single sign-on is disabled. Password Select this option to define a password for the Citrix connection, if single sign-on is disabled. Domain Name Select this option to define a domain name for the Citrix connection. Window Size Select this option to specify the window size for the Citrix connection. From the drop-down menu, select a window size.
Table 102. Server options Option Description Logon Method Select this option to choose a logon method for your Citrix connection. ● Default Logon Method ● Prompt Logon Method Table 103. Advanced settings Option Description Disable Full Screen Pop-up Select this option to disable the full screen pop-up warning. Logon—Connect to Active and Disconnected Sessions Select this option to connect to the active and disconnected sessions after you log in.
Table 105. Configuring remote connections—VMware (continued) Option Description ● Blast Login as Current User Select this option to enable the single sign-on feature for the connection. If you enable the login as current user option, use your Windows login credentials to connect to the VMware server. Username Select this option to define a user name for the VMware connection, if single sign-on is disabled.
Table 106. Configuring basic settings (continued) Option Description Password Select this option to define a password for the connection, if single sign-on is disabled. Domain Name Select this option to define a domain name for the connection. Auto Reconnect Select this option to enable the connection to automatically reconnect, if the connection is dropped. Table 107. Configuring RD gateway Option Description Use RD Gateway settings Select this option to configure the settings for RD Gateway.
Table 109. Configuring other settings—Experience Option Description Connection Speed To Optimize the Performance Select this option to specify the connection speed to optimize the performance. Desktop Background Select this option to enable the desktop background for the connection. Visual Styles Select this option to enable the visual styles for the connection. Font Smoothing Select this option to enable font smoothing for the connection.
Table 110. Configuring local resources (continued) Option Description Enable the redirection of Other supported Plug and Play devices Select this option to enable or disable the redirection of other plug and play devices. Configuring remote connection settings—Browser Use this page to configure the browser connection settings, such as IE proxy and favorites, for the Windows Embedded Standard devices. Table 111.
Table 114. Firewall (continued) Option Description Public Firewall Select this option to enable the public firewall. Table 115. Aero—valid for Windows Embedded Standard 7 Option Description Aero Select this option to enable the Aero feature for the browser. NOTE: This feature is available only for Windows Embedded Standard 7 Latitude mobile thin client BIOS settings Use this page to define the BIOS settings of Latitude mobile thin clients. Table 116.
Table 120. Admin password settings Parameter Description Enable Admin Password Select this check box to enable the BIOS administrator password. Successful changes to this password take effect immediately. Admin Password Enter the new BIOS admin password. This option is available only if you select the Enable Admin Password check box. Table 121. Power management settings Parameter Description Wake On LAN Enable this option to power on the device from the Wyse Management Suite console.
Table 126. Admin password settings Parameter Description Enable Admin Password Select this check box to enable the BIOS administrator password. Successful changes to this password take effect immediately. Admin Password Enter the new BIOS admin password. This option is available only if you select the Enable Admin Password check box. Table 127. Auto-On settings Parameter Description Auto On From the drop-down list, set the time of day you want the system to turn on automatically. Table 128.
Configuring device information Use the Device Info page to set the device details. Table 131. Configuring device information Option Description Location Enter the device location. Contact Enter the device contact. Custom 1 to 3 Enter the custom values. Configuring Wyse Easy Setup settings Use this page to configure the Wyse Easy Setup settings for the control panel and the user interface. Table 132.
Table 136. Configuring taskbar Option Description Date & Time Select this option to display the date and time option in the taskbar. Sound Select this option to display the sound option in the taskbar. Network Select this option to display the network option in the taskbar. Touch Keyboard Select this option to display the touch keyboard option in the taskbar. Table 137. Configuring Start menu Option Description Allow Shutdown Select this option to shut down the system.
Configuring Linux policy settings To configure the policy settings for Linux devices, do the following: 1. Select a group and click Edit Policies. 2. From the menu, select Linux. 3. After configuring the options, click Save and Publish. Figure 7.
Table 140. System personalization (continued) Setting Description Monitor Rotation Allows you to define the orientation of the monitor. From the drop-down list, select either Vertical or Horizontal based on your preference. Enable Dual Monitor Allows you to enable the dual monitor functionality. When you select this check box, the following options are displayed: ● Mirror Mode—Display is mirrored. ● Span Mode—Display is spanned.
Table 141. Desktop experience (continued) Parameter Description Wallpaper File Allows you to select your preferred wallpaper. Images uploaded to the file repository are displayed. Wallpaper Layout Allows you to set the wallpaper Layout. From the drop-down menu, select your preferred wallpaper layout. The default wallpaper layout is center.
Table 142. Login experience (continued) Setting Description Admin Password Enter the password if you want to change the admin password. Thinuser Password Enter the password if you want to change the thinuser password. Guest Password Enter the password if you want to change the guest password. Network Use this page to configure the network settings. Table 143. Network settings Parameter Description Wireless Connection Name Enter the name of the connection.
Table 144. Security (continued) Setting Description Require User to enter password Allows you to set the VNC password. VNC Password Allows you to enter the VNC password. Prompt user on VNC session start Allows you to enable a popup message for accepting the incoming VNC connection request. Configuring central configuration settings Use this page to enter the file server, firmware server, root path, and the corresponding user credentials. Table 145.
Table 146. Other settings (continued) Parameter Description ● ● ● ● Interactive Restart Shutdown None DHCP Vendor ID Allows you to change the DHCP Vendor ID. The default Vendor ID is wyse-5000. Browser Homepage Allows you to change the browser homepage. Enter the URL address of your choice to set the browser homepage. VDI global settings Use this page to configure the global settings for Citrix and VMware View clients. Table 147.
Table 147. Citrix general (continued) Parameter Description Transparent Key Passthrough Allows you to determine how the mapping of certain key combinations is used when connecting to ICA sessions. From the drop-down menu, select any one of the following options: ● Local ● Remote ● Full Screen Only Use Alternate Address Allows you to use an alternate IP address from the ICA master browser to pass firewalls. ICA Proxy Type Allows you to select the proxy type for the ICA connection.
Table 151. Remote connection Citrix Parameter Description Connection Name Allows you to enter a name to identify the connection. Auto Launch Connection on Logon Allows you to automatically launch the connection after you log in. Connection Type Allows you to set a connection type. From the drop-down menu, select any one of the following options: ● Server Connection ● Published Application ● Store Front Citrix Server FQDN or IP Address Allows you to enter the IP address or FQDN of the Citrix server.
Table 151. Remote connection Citrix (continued) Parameter Description ● ● ● ● ● ● ● Seamless 640 x 480 1024 x 768 800 x 600 1280 x 1024 1600 x 1200 Full Screen Screen Color Depth Allows you to set a screen color depth. From the drop-down menu, select any one of the following options: ● 64K ● 256 ● 16M Auto Reconnect Allows you to enable the thin client to reconnect to the Citrix session automatically.
Table 152. Remote connection VMware (continued) Parameter Description Security Mode Allows you to set the security mode. From the drop-down menu, select any one of the following options: ● Never connect to untrusted servers ● Warn before connecting to untrusted servers ● Do not verify server identity certificates. Fullscreen Mode Allows you to view the remote session in the fullscreen mode. Window Size Allows you to set a window size.
Table 153. Remote connection RDP (continued) Setting Description Window Size Allows you to set a window size. From the drop-down menu, select any one of the following options: ● Default ● 640 x 480 ● 1024 x 768 ● 800 x 600 ● 1280 x 1024 ● 1600 x 1200 ● Full Screen Forward All Printers Allows you to forward all the printers to the remote connection. Auto Reconnect Allows you to enable the thin client to reconnect to the RDP session automatically.
Table 154. Remote connection browser (continued) Setting Description Auto launch Connection on Logon Allows you to automatically launch the connection during login. URL Enter the starting URL. Kiosk Mode Allows you to enable the kiosk mode. Window Size Allows you to set a window size. From the drop-down menu, select the size of the window of your choice. Auto Reconnect Allows you to enable the thin client to reconnect the browser automatically.
Figure 8. ThinLinux The ThinLinux thin client policy settings include the following options: ● System Personalization ● Desktop Experience ● Login Experience ● Network ● Security ● Central Configuration ● Other settings ● VDI Global Settings ● Remote Connections Citrix ● Remote Connections VMware ● Remote Connections RDP ● Remote Connections Browser ● Advanced Settings ● Device Info ● BIOS ThinLinux 3040 Settings System personalization Use this page to configure the system personalization. Table 156.
Table 156. Display (continued) Parameter Description Enable Dual Monitor Allows you to enable the dual monitor functionality. If you select this check box, the following options are displayed: ● Display Mode—Use this option to set the Display mode. ● Monitor Resolution (Secondary)—From the drop-down menu, select your preferred monitor resolution. ● Span Position—From the drop-down menu, select any one of the following options: ○ On Left ○ On Right ○ Bottom ○ Top Table 157.
Table 161. Audio (continued) Parameter Description Audio Mute Allows you to set the thin client to mute mode. Microphone Volume Allows you to set the microphone volume of the thin client. The range of the microphone volume is 0–100. Microphone Mute Allows you to set the microphone to mute mode. Desktop experience Use this page to configure the desktop settings, such as desktop wallpaper, wallpaper layout, and the desktop shortcut keys. Table 162.
Table 163. Login experience (continued) Parameter Description Root Password Enter the password if you want to change the root password Thinuser Password Enter the password if you want to change the thinuser password Network Use this page to configure the network settings. Table 164. Network Parameter Description Wireless Connection Name Enter the name of the connection SSID Enter the name of the Service Set Identifier (SSID) connection.
Table 167. Configuring VNC settings (continued) Option Description VNC Password Select this option to enter the VNC password. Prompt user on VNC session start Select this option to enable a popup message for accepting the incoming VNC connection request. Central configuration Use this page to enter the file server, firmware server, root path, and the corresponding user credentials. Table 168.
Table 169. Other settings (continued) Parameter Description Power Button Action From the drop-down menu, select any one of the options: ● Interactive ● Restart ● Shutdown ● None The options define the action to be taken when you press the power button. DHCP Vendor ID Allows you to change the DHCP Vendor ID. The default Vendor ID is wyse-5000. Browser Homepage Allows you to change the browser homepage. Enter the URL address of your choice to set the browser homepage.
Table 170. Citrix General (continued) Parameter Description Enable UDP Audio Allows you to enable the transport of audio data through UDP. Flash Redirection Policy Allows you to either allow or deny Flash Redirection Policy. Transparent Key Passthrough Allows you to determine how the mapping of certain key combinations is used when connecting to ICA sessions.
Table 174. Remote connection Citrix Parameter Description Connection Name Allows you to enter a name to identify the connection. Auto Launch Connection on Logon Allows you to automatically launch the connection after you log in. Connection Type Allows you to set a connection type. From the drop-down menu, select any one of the following options: ● Server Connection ● Published Application ● Store Front Connection Server Allows you to enter the IP address or FQDN of the Citrix server.
Table 174. Remote connection Citrix (continued) Parameter Description ● ● ● ● ● 1024 x 768 800 x 600 1280 x 1024 1600 x 1200 Full Screen Screen Color Depth Allows you to set a screen color depth. From the drop-down menu, select any one of the following options: ● 64K ● 256 ● 16M Auto Reconnect Allows you to enable the thin client to reconnect to the Citrix session automatically. Delay before trying to reconnect Allows you to set the time in seconds to delay the reconnection attempt.
Table 175. Remote connection VMware (continued) Parameter Description Lock the Server URL / Host field Select the check box to lock the server URL. Security Mode Allows you to set the security mode. From the drop-down menu, select any one of the following options: ● Never connect to untrusted servers ● Warn before connecting to untrusted servers ● Do not verify server identity certificates. Fullscreen Mode Allows you to view the remote session in the fullscreen mode.
Table 176. Remote connection RDP (continued) Parameter Description Domain Name Enter the domain name. Window Size Allows you to set a window size. From the drop-down menu, select any one of the following options: ● Default ● 640 x 480 ● 1024 x 768 ● 800 x 600 ● 1280 x 1024 ● 1600 x 1200 ● Full Screen Forward All Printers Allows you to forward all the printers to the remote connection. Auto Reconnect Allows you to enable the thin client to reconnect to the RDP session automatically.
Table 178. Remote connection browser (continued) Parameter Description Window Size Allows you to set a window size. From the drop-down menu, select the size of the window of your choice. Auto Reconnect Allows you to enable the thin client to reconnect the browser automatically. Delay before trying to reconnect Enter the time in seconds to delay the reconnection attempt. When you select the Auto Reconnect check box, this option is displayed.
Table 182. Configuring system configuration (continued) Option Description Integrated NIC From the drop-down list, select the preferred option. Audio Select this option to enable the audio device. Table 183. Configuring USB configuration Option Description Enable USB Boot Support Select this check box to enable the USB boot setup. Allows you to boot any type of USB Mass Storage Devices. Enable Front USB Ports Select this check box to enable the device attached to this port.
Table 188. Configuring auto-on settings Option Description Auto On From the drop-down list, set the time of day you want the system to turn on automatically. Table 189. Configuring post behavior settings Option Description Numlock LED Select the check box to turn on the NumLock LED light when the systems restarts. Keyboard Errors Select the check box to display the keyboard related errors when the systems restarts.
Figure 9.
Table 191. Configuring display options (continued) Option Description Monitor Rotation (Primary) Select this option to set an orientation for your monitor. From the drop-down menu, select one of the following options based on your preference: ● Landscape ● Portrait ● Landscape—flipped ● Portrait—flipped Table 192. Configuring keyboard options Option Description Language Select this option to select one or more input languages for your keyboard.
Table 194. Configuring basic mouse options Option Description Click Lock Select this option to highlight or to drag the pointer without holding down the mouse button. To set the Click Lock Time Option, from the drop-down menu, select the appropriate time for the mouse button to be held down before the click is locked. Double Click Speed Select this option to set the time interval between two consecutive mouse clicks. From the drop-down menu, select your preferred option. Table 195.
Table 199. Configuring audio settings (continued) Option Description Audio Volume Select this option to adjust the audio volume of your device. From the drop-down menu, select your preferred volume option. Microphone Mute Select this option to mute your microphone. Microphone Volume Select this option to adjust the volume of your microphone. From the drop-down menu, select your preferred volume option.
Configuring security and lockdown settings Use this page to configure the security and lockdown settings. Table 202. Security and lockdown Option Description Install Certificates Select this option to view the certificates that are uploaded to the file repository. Disable USB Storage Device Access Select this option to enable or disable the USB mass storage device access for non-administrator users.
Table 205. Power settings on battery (continued) Option Description Turn Off Display (on battery) Select this option to set the time after which the display is turned off. From the drop-down list, select a delay time. Table 206. Power settings when plugged-in Option Description Device Sleep Plan (plugged-in) Select this option to set the time after which your device goes to sleep mode. From the drop-down menu, select a delay time.
Table 209. Configuring basic options (continued) Option Description Citrix Server FQDN or IP address Select this option to list the Citrix servers. Enter the list of ICA browsers separated by commas for the connection. Published Applications Select this option to specify a published application that you want to start. Single Sign On Select this option to enable the single sign on feature for the connection.
Table 210. Configuring application display settings (continued) Option Description Start Menu Display Select this option to enable the start menu display on the connection desktop. After you enable this option, specify the Start Menu Display Folder for the connection. System Tray Display Select this option to display the Citrix connection icon in the notification area. Table 211.
Table 214. Configuring remote connection settings—VMware (continued) Option Description Auto Launch Connection On Logon Select this option to enable the connection to automatically start after you log in. VMware Server Address Select this option to enter the server address of the VMware connection. Protocol Select this option to choose the protocol for the VMware connection.
Table 215. Configuring basic settings (continued) Option Description Server Address Select this option to enter the server address of the connection. Single Sign On Select this option to enable the single sign-on feature for the connection. If you enable the login as current user option, use your Windows login credentials to connect to the server. Username Select this option to define a user name for the connection, if single sign-on is disabled.
Table 217. Configuring display settings (continued) Option Description Screen Color Depth (in bits) Select this option to define the screen color depth of the connection. ● RDP 15–Bit High Color ● RDP 16–Bit High Color ● RDP 24–Bit True Color ● RDP 32–Bit Highest Quality Table 218. Configuring other Settings—Local and Parameter Option Description Remote Audio Play Back Select this option to manage the audio playback in the remote connection.
Table 220. Configuring other settings—Experience Option Description Connection Speed To Optimize the Performance Select this option to specify the connection speed to optimize the performance. Desktop Background Select this option to enable the desktop background for the connection. Visual Styles Select this option to enable the visual styles for the connection. Font Smoothing Select this option to enable font smoothing for the connection.
Table 222. Configuring Internet Explorer (IE) favorites and trusted site settings Option Description IE Favorite Select this option to add your favorite and trusted sites. Perform the following steps to add your favorite and trusted sites: ● Click Add Site, and enter the folder name, URL, and description. ● Click Create Shortcut to create a shortcut for the site. ● Click Remove to delete a site from the list. NOTE: The URL must begin with https:// when the Trusted Sites check box is selected.
Table 227. Configuring VNC settings Option Description Enable VNC Select this option to enable the VNC Server. VNC User Prompt If you select this option, you must accept or decline VNC shadowing. VNC User Required Password Select this option to set the VNC password. VNC Primary Password Select this option to change the VNC password. Enter the new password with a maximum of eight characters. VNC View-only Password Enter the primary password. You cannot edit the password.
5 Managing devices This section describes how to perform a routine device management task by using the management console. To locate the inventory of the devices, click the Devices tab. You can view a subset of the devices by using various filter criteria, such as groups or subgroups, device type, operating system type, status, subnet, platform, or time zone. To view the Device Details page of a particular device, click the device entry listed on the page.
Steps 1. From the Configuration Groups drop-down list, select either the default policy group or the groups which are added by an administrator. 2. From the Status drop-down list, select any one of the following options: ● Registration ○ Registered ○ Not Registered ○ Compliant ○ Pending ○ Non-Compliant ● Online Status ○ Online ○ Offline ○ Unknown ● Others ○ Recently Added 3.
● For a private cloud, register a thin client by providing the Wyse Management Suite URL, and the group token (Optional for the group to which you want to register this device. Devices are registered to the unmanaged group, if the group token is not provided. Registering ThinOS thin clients through WDA User Interface Prerequisites Creating a group is a pre-requisite for registering the thin client to the Wyse Management Suite. Steps 1.
The Wyse Device Agent window is displayed. 2. Enter the device registration details. 3. In the Wyse Management Suite tab, enter the Wyse Management Suite server address. 4. Enter the group token. 5. Click Register. After the registration is complete, the Registered to Wyse Management Suite message is displayed.
Registering devices by using DNS SRV record DNS based device registration is supported with the following versions of Wyse Device Agent: ● Windows Embedded Systems—13.0 or later versions ● Thin Linux—2.0.24 or later versions ● ThinOS—8.4 firmware or later versions You can register devices with the Wyse Management Suite server if DNS SRV record fields are set with valid values. NOTE: For detailed instructions on how to add DNS SRV records on the Windows server, see Creating and configuring DNS SRV record.
Table 230. Configuring device by using DNS SRV record (continued) URL/Tag Description Enter False , if you have not imported the SSL certificates from a well-known authority for https communication between the client and Wyse Management Suite server. NOTE: CA Validation is optional for the latest version of Wyse Management Suite.
Table 231. Device details (continued) Parameter Description A window is displayed with the repository and server details. 3. Select the check box. Export Devices to CSV Allows you to generate a CSV with a list of the asset information for all the devices filtered on the screen. Summary tab Allows you to view and manage information on the Notes, Group Assignment, Alerts, and Device Configuration. Update Image Displays a schedule in the WES Firmware Update Job window.
Table 231. Device details (continued) Parameter Description On the Performance metric console, the following details are displayed: ○ Average CPU last minute. ○ Average memory usage last minute. 2. Click Clear. Installed Apps This option is available for Windows Embedded Standard, Linux, and ThinLinux devices. The current number of installed applications is displayed next to the Installed Apps title.
Figure 12. Pull OS image screen Table 232. Pull OS image screen details Option Description Name of Image Provide a name for the image. To replace the image with a similar name and the image files which are not completed successfully, click Override name. File repository From the drop-down menu, select the file repository to where the image is uploaded.
● Pull after sysprep—The device restarts, and logs into the operating system in a disabled state. Run the custom sysprep. After the custom sysprep is complete, the device boots to merlin operating system and the image pull operation is performed. ● Pull now—The device boots to merlin operating system and the image pull operation is performed. NOTE: ● Wyse Device Agent and Merlin must be upgraded on your devices. ● Legacy on-premise gateway does not support the image pull operation.
Renaming thin client Use this page to change the host name of Windows Embedded Standard, ThinLinux, and ThinOS thin clients. To change the host name, do the following: 1. On the Devices page, click the device. 2. From the More options drop-down list, select the Change Host Name option. 3. Enter the new host name when prompted. NOTE: Host name can only contain alphanumeric characters, and a hyphen. 4. For Windows Embedded Standard devices, the Reboot drop-down list is included in the Alert window.
6 Apps and data This section describes how to perform routine device application tasks, operating system imaging, inventory management, and set policies by using the management console. Figure 15. Apps and data Windows Embedded Standard operating system image updates are performed in the Apps and Data tab. Wyse Management Suite supports the following two types of application deployment policies: ● Standard application—This policy allows you to install a single application package.
Topics: • • • • • • • Configuring app inventory Deploying applications to thin clients Adding Windows Embedded Standard operating system and ThinLinux images to inventory Managing ThinOS firmware inventory Managing Windows Embedded Standard and ThinLinux image policies Managing file repository Changing wallpaper for all devices belonging to marketing group Configuring app inventory Prerequisites This section allows you to view and add an application to the inventory.
b. Place the Windows Embedded Standard imaging files in the \repository\osImages\Zippedfolder. The image is automatically extracted and placed in a valid folder. The image is listed in the Windows Embedded Standard image inventory. Deploying applications to thin clients The standard application policy allows you to install a single application package and requires reboot before and after installing each application.
Table 233. Add advanced app policy (continued) Parameter Description Task Allows you to specify the task for the policy. From the dropdown menu, select the task. OS Type Allows you to select the OS type for the policy. Application Allows you to add or remove the application from the policy. Click the Add app option and select the preferred application. NOTE: The preferred order of the package update is RTME, FR, TCX, and Blast. OS Subtype Filter Allows you to select the filter for the OS subtype.
The image is added to the repository. 2. Go to Apps and data > OS image repository > WES/ThinLinux to view the registered image. Managing ThinOS firmware inventory To add a file to the ThinOS image inventory, do the following: Steps 1. In the Apps & Data tab, under OS Image Repository, click WTOS. 2. Click Add File. The Add File screen is displayed. 3. To select a file, click Browse and navigate to the location where your file is located. 4. Enter the description for your file. 5.
Managing file repository This section allows you to view and manage the file repository inventories, such as thin client wallpaper, logo, EULA text file, Windows wireless profile, and certificate files. To add a new file, do the following: 1. In the Apps & Data tab, under File Repository, click Inventory. 2. Click Add File. The Add File screen is displayed. 3. To select a file, click Browse and navigate to the location where your file is located. 4.
Click Jobs to check the status of configuration policy. You can click the number next to the status flag in the Details column to check devices with their status.
7 Managing rules This section describes how to add and manage the rules in the Wyse Management Suite console. The following filtering options are provided: ● Registration ● Unmanaged Device Auto Assignment ● Alert Notification Topics: • • • Registering unmanaged devices Creating unmanaged device auto assignment rules Alert Notification Registering unmanaged devices Configure the rules for unmanaged devices by using the Registration option.
Figure 18. Edit Rule 4. Click Save. Creating unmanaged device auto assignment rules To create rules for the unmanaged device auto assignment, do the following: NOTE: Make sure that you have installed the pro license version of Wyse Management Suite. 1. Click the Rules tab. 2. Select the Unmanaged Device Auto Assignment option. 3. Click the Add Rules tab. Figure 19. Unmanaged Device Auto Assignment Rules 4. Enter the Name and select the Destination group. 5.
The rule is displayed in the unmanaged group list. This rule is applied automatically and the device is listed in the destination group. Editing unmanaged device auto assignment rule 1. Click the Rules tab. 2. Select the Unmanaged Device Auto Assignment option. 3. Select the rule and click the Edit option. 4. Click Save. Disabling and deleting rule 1. Click the Rules tab. 2. Select the Unmanaged Device Auto Assignment option. 3. Select a rule and click the Disable Rule option. 4.
b. Enter the Description. c. From the drop-sown list, select a target device to apply Notification Target and the time duration to apply Notification Frequency. Figure 21. Add Rule 2. Click Save.
8 Managing Jobs This section describes how to schedule and manage jobs in the management console. Figure 22. Jobs In this page you can see jobs based on the following filtering options: ● Configuration Groups—From the drop-down menu, select the configuration group type. ● Scheduled by—From the drop-down menu, select a scheduler who performs the scheduling activity.
○ 1 or more completed ● More Actions—From the drop-down menu, select the Sync BIOS Admin Password option. The Sync BIOS Admin Password Job window is displayed Topics: • • • • Sync BIOS admin password Scheduling the image policy Scheduling the application policy Scheduling the device command job Sync BIOS admin password From the More Actions drop-down menu, select the Sync BIOS admin password option. To synchronize the BIOS admin password, do the following: 1. Enter the password.
The App Policy Job screen is displayed. 2. From the drop-down list, select a policy. 3. Enter the job description. 4. From the drop-down list, select the date or time. 5. Enter/select the following details: ● Effective— Enter the starting and ending date. ● Start between—Enter the starting and ending time. ● On day(s)—Select the days of the week. 6. Click the Preview option to view the details of the scheduled job. 7. On the next page, click the Schedule option to initiate the job.
9 Events This section describes how to view all events and alerts in the management system using the management console. It also provides instructions on viewing an audit of events and alerts for system auditing purposes. A summary of events and alerts is used to obtain an easy-to-read daily summary of what has happened in the system. The Audit window arranges the information into a typical audit log-view. You can view the timestamp, event type, source, and description of each event in the order of time.
○ This Week ○ Custom ● Event Groups—All the events are classified under particular groups. The available options in the drop-down menu are: ○ Access ○ Registration ○ Configuration ○ Remote Commands ○ Management ○ Compliance Viewing audit log Prerequisites The Audit window arranges the information into a typical audit log-view. You can view the timestamp, event type, source, and description of each event in the order of time. Steps 1. Go to Events > Audit. 2.
10 Managing users This section describes how to perform a routine user management task in the management console. The following are the two types of users: ● Administrators—Wyse Management Suite administrator can be assigned the role of a global administrator, group administrator, or viewer. ○ A Global Administrator has access to all the Wyse Management Suite functions. ○ A Group Administrator has access to all assets and functions for specific groups that are assigned to them.
Figure 25. Unassigned admins NOTE: To import users from the CSV file, click Bulk Import. Topics: • • • • Adding new admin user Editing admin user Deactivating admin account Deleting admin Adding new admin user Prerequisites To add an admin user, do the following: Steps 1. Enter your email ID and user name in the respective fields. 2. Select the check box to use the same user name as mentioned in the email. 3.
NOTE: When you update the login name, you are forced to log out from the console. Log in to the console using the updated account login name. 2. Do one of the following: ● If you click the Personal Information tab, enter the following details: ○ First name ○ Last name ○ Title ○ Mobile phone number ● If you click the Roles tab, enter the following details: a. In the Roles section, from the Role drop down list, select the Administrator role. b. In the Password section, do the following: i.
11 Portal administration This section contains a brief overview of your system administration tasks that are required to set up and maintain your system. Figure 26. Portal admin Topics: • • • Configuring console settings Configuring account settings System setup Configuring console settings This section helps you to configure settings for the Wyse Management Suite console.
6. Click Import. 7. Enter the user name and password. 8. Click Login. 9. On the User Group page, click Group name and enter the group name. 10. In the Search field, type the group name you want to select. 11. Select a group. The selected group is moved to the right pane of the page. 12. Click Next. 13. Click Import Users. NOTE: If you provide an invalid name or do not provide a last name, or provide any email address as name, then the entries cannot be imported into Wyse Management Suite.
d. To enable tenants to configure Single Sign-On by using ADFS, select the Enable SSO login using ADFS check box. This feature follows the Security Assertion and Markup Language (SAML) standard specification. e. To validate the configuration information, click Test ADFS Login. This enables tenants to test their setup before saving. NOTE: Tenants can activate/deactivate SSO login by using ADFS. 5. Click Save. 6. After you save the metadata file, click Update Configuration.
● Wyse Management Suite Repository—Log in to Wyse Management Suite public cloud, go to Portal Admin > File Repository and download the Wyse Management Suite repository installer. After the installation, register the Wyse Management Suite repository to Wyse Management Suite Management server by providing the required information. To 1. 2. 3. 4. 5. 6. 7. 8. use Wyse Management Suite repository, do the following: Download the Wyse Management Suite repository from the public cloud console.
1. You must select the check box to enable the two factor authentication. NOTE: Administrators must verify the second authentication factor using one time passcodes to log in to the management portal. 2. You will receive a onetime passcode to your e-mail address. Enter one time passcode to verify. By default, you have eight attempts to verify the one time passcode. If you fail to verify the passcode, the account will be locked. Only global administrators can unlock locked accounts.
Figure 28. Types of report 4. Select the delimiter. 5. Click Save. Multi Tenant This section allows you to create an additional organization. You can manage the organizations independently. Each account must have its own license key and can set up its own set of admin accounts, policies, operating system images, application, rules, alerts, and so on. The high level operator creates these organizations. 1. Select the check box to enable multi-tenant option. 2.
Configuring account settings This section helps you to configure account settings for Wyse Management Suite console. Custom branding This option allows you to add the name of your company and its logo or brand. You can upload your own header logo, favicon, add a header title, and change header colors to customize the Wyse Management Suite portal. About this task To access and specify custom branding: Steps 1. Go to Portal Administrator > Account > Custom Branding. 2. Click Enable Custom Branding 3.
● Key/Certificate: Upload HTTPS key/certificate file pair (only PEM format is supported). ● PKCS-12: Upload HTTPS PKCS-12 (.pfx, .p12). Apache intermediate certificate is required for IIS pfx. 4. Click Save.
A Installing or upgrading Wyse Device Agent Prerequisites This section provides information about how to install or upgrade Wyse Device Agent on your thin clients, such as Windows Embedded Standard, Linux, and ThinLinux devices, by using Wyse Management Suite. ● Windows Embedded Standard devices—Wyse Device Agent version 14 can be downloaded from https://www.dell.
Steps 1. Copy the WDA.exe file to the thin client. 2. Double-click the WDA.exe file. NOTE: ● Different Wyse Device Agent packages are available for each variant of Windows Embedded Standard. ● A warning message is displayed when an older version of Wyse Device Agent or HAgent is installed on the device. 3. Click Yes. 4. In the Group token field, enter a group token. This is an optional field. To skip this step, click Next. You can enter the group token details later in the Wyse Device Agent User Interface.
B Wyse Management Suite feature matrix The following table provides information about the features supported for each subscription type: Table 234.
Table 234. Feature matrix for each subscription type (continued) Features Wyse Management Suite Standard Wyse Management Suite Pro-private cloud Wyse Management Suite Pro-cloud edition Two-factor authentication Supported Supported Supported Active directory authentication for role based administration.
C Supported thin clients on Wyse management Suite The following table lists the supported thin clients on Wyse Management Suite: Table 235. Supported thin clients Operating System Device Type Build number Linux Wyse 5010 thin client 11.3.106 Wyse 7010 thin client WDA version 2.0.11-00.1 and later Wyse 5020 thin client Platform utility version 1.0.3-0.1 and later Wyse 7020 thin client ThinLinux Wyse 5020 thin client 1.0.3 Wyse 5060 thin client WDA version 2.0.24-00.
Table 235. Supported thin clients (continued) Operating System Device Type Build number Wyse 5060 thin client 7038 WDA versions 14.x and later. merlin version 3.4.6 and later Windows 10 IoT Enterprise (WIE10) Wyse 5020 thin client 0A0F Wyse 7020 thin client WDA versions 14.x and later. Latitude 3480 mobile thin client merlin version 3.4.6 and later Latitude 5280 mobile thin client Windows Embedded 8 Standard (WE8S) Wyse 5010 thin client 924 Wyse 7010 thin client WDA versions 14.x and later.
D Wireless profiles password editor This Wireless profiles password editor is used to capture the wireless profiles and edit the passwords. The profiles are saved in an XML file. The same XML file can be used to configure the Wyse Management Suite through Cloud Client Manager. NOTE: .NET Framework 4.5 must be installed to run this tool on any Windows operating system or Windows Embedded operating system.
Limitations of Wireless Profiles Password Editor The following are the limitations of Wireless Profiles Password Editor: ● Passwords are valid only for the following authentication types: ○ WPAPSK ○ WPA2PSK ● Passwords do not exist for the following enterprise authentication profile types: ○ WPA ○ WPA2 152 Wireless profiles password editor
E Creating and configuring DHCP option tags About this task To create a DHCP option tag, do the following: Steps 1. Open the Server Manager. 2. Go to Tools and click DHCP option. 3. Go to FQDN > IPv4 and right-click IPv4. Figure 30. DHCP 4. Click Set Predefined Options. The Predefined Options and Values window is displayed. 5. From the Option class drop-down menu, select the DHCP Standard Option value.
Figure 31. Predefined Options and Values 6. Click Add. The Option Type window is displayed. Figure 32. Option Type Example The options need to be either added to the server options of the DHCP server or scope options of the DHCP scope. Configuring the DHCP option tags ● To create the 165 Wyse Management Suite server URL option tag, do the following: 1. Enter the following values and click OK. ○ Name—WMS ○ Data type—String ○ Code—165 ○ Description—WMS_Server 2. Enter the following value and then click OK.
String—WMS FQDN For example, WMSServerName.YourDomain.Com:443. Figure 33. 165 Wyse Management Suite server URL option tag ● To create the 166 MQTT server URL option tag, do the following: 1. Enter the following values and click OK. ○ Name—MQTT ○ Data type—String ○ Code—166 ○ Description—MQTT Server 2. Enter the following value and click OK. String—MQTT FQDN For example, WMSServerName.YourDomain.
Figure 34. 166 Wyse Management Suite server URL option tag ● To create the 167 Wyse Management Suite CA Validation server URL option tag, do the following: 1. Enter the following values and click OK. ○ Name—CA Validation ○ Data type—String ○ Code—167 ○ Description—CA Validation 2. Enter the following values, and click OK.
Figure 35. 167 Wyse Management Suite server URL option tag ● To create the 199 Wyse Management Suite Group Token server URL option tag, do the following: 1. Enter the following values and click OK. ○ Name—Group Token ○ Data type—String ○ Code—199 ○ Description—Group Token 2. Enter the following values and click OK.
Figure 36.
F Creating and configuring DNS SRV records About this task To create a DNS SRV record, do the following: Steps 1. Open the Server Manager. 2. Go to Tools and click DNS option. 3. Go to DNS > DNS Server Host Name > Forward Lookup Zones > Domain > _tcp and right-click the _tcp option. Figure 37. DNS Manager 4. Click Other New Records. The Resource Record Type window is displayed. 5.
Figure 38. Resource Record Type a. To create Wyse Management Suite server record, enter the following details and click OK.
Figure 39. _WMS_MGMT service b. To create MQTT server record, enter the following values, and then click ÓK.
Figure 40. _WMS_MQTT service 6. Go to DNS > DNS Server Host Name > Forward Lookup Zones > Domain and right-click the domain. 7. Click Other New Records. 8.
Figure 41. Resource Record Type a. To create Wyse Management Suite Group Token record, enter the following values, and click OK.
Figure 42. _WMS_GROUPTOKEN record name b. To create Wyse Management Suite CA validation record, enter the following values, and then click OK.
Figure 43.
