Dell Wyse Management Suite Version 1.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents 1 Introduction to Wyse Management Suite........................................................................................................9 Editions................................................................................................................................................................................9 What is new in this release?.............................................................................................................................................
Configuring remote connection settings—Browser............................................................................................. 80 Configuring Latitude mobile thin client BIOS settings........................................................................................... 81 Configuring Wyse 7040 thin client BIOS settings..................................................................................................83 Configuring device information...........................................
Configuring power settings..................................................................................................................................... 128 Configuring security settings.................................................................................................................................. 128 Upgrading firmware settings...................................................................................................................................
Rename the thin client....................................................................................................................................................161 Configuring remote shadow connection......................................................................................................................162 Shutting down devices..................................................................................................................................................
9 Managing Events........................................................................................................................................186 Searching an event or alert by using filters................................................................................................................. 186 Searching an event or alert by using filters........................................................................................................... 187 Viewing a summary of events..........
Security Level........................................................................................................................................................... 207 Manual discovery from the client.......................................................................................................................... 208 Adding the PCoIP endpoint vendor class to DHCP server................................................................................
1 Introduction to Wyse Management Suite Wyse Management Suite is the next generation management solution that enables you to centrally configure, monitor, manage, and optimize your Dell Wyse thin clients. It also offers advanced feature options such as cloud as well as on-premises deployment, managefrom-anywhere option by using a mobile application, enhanced security such as BIOS configuration and port lockdown.
• Wyse Management Suite components such as Open JDK and Tomcat services are updated. • Public cloud storage of ThinOS packages is supported. • Unified workflow for ThinOS firmware and package is integrated. • Option to add package from Apps & Data is integrated. • Teradici EMSDK component is updated to support Open JDK 11. • Option to export or import a policy configuration is integrated.
2 Getting started with Wyse Management Suite This section provides information about the general features to help you get started as an administrator and manage thin clients from the Wyse Management Suite software.
Prerequisites to deploy Wyse Management Suite on the private cloud Table 1.
Functional areas of management console The Wyse Management Suite console is organized into the following functional areas: • The Dashboard page provides information about the current status on each functional area of the system. • The Groups & Configs page employs a hierarchical group policy management for device configuration. Optionally, subgroups of the global group policy can be created to categorize devices according to corporate standards.
Configuration policies are published immediately, and cannot be scheduled for a later time. Few policy changes, for example display settings, may force a reboot. Application and operating system image deployment—Applications and operating system image updates can be deployed from the Apps & Data tab. Applications are deployed based on the policy groups. NOTE: Advanced application policy allows you to deploy an application to the current and all subgroups based on your requirement.
3 Wyse Management Suite dashboard The Dashboard page enables you to view the status of a system, and the recent tasks that are performed within the system. To view a particular alert, click the link in the Alerts section. The Dashboard page also allows you to view the device summary. Figure 1.
The alerts summary is displayed. 2 Click View All Alerts. The Events page is displayed with list of all the alerts. View the list of events The Events section displays the summary of events that have occurred in the last few days. To view the detailed list of all the events, do the following: 1 Click Dashboard. The events summary is displayed. 2 Click View All Events. The Events page is displayed with list of all the events.
Change your password To change your password, do the following: 1 On the upper-right corner of the Dashboard page, click the login drop-down menu. 2 Click Change Password. The Change Password window is displayed. 3 Enter the current password. 4 Enter the new password. 5 Reenter the new password for confirmation. 6 Click Change Password. Log out To log out from the management console, do the following: 1 On the upper-right corner of the Dashboard page, click the login drop-down menu.
4 Managing groups and configurations The Groups & Configs page enables you to define policies that are required to configure your devices. You can create sub groups of the global group policies and categorize devices based on your requirements. For example, devices may be grouped based on job functions, device type, and so on. Figure 2.
NOTE: • When you modify the lower-level policies, a bullet symbol is displayed next to the policy. This symbol indicates that the policy is an override to a higher-level policy. For example, System Personalization, Networking, Security, and so on. • When you modify policies, an asterisk (*) is displayed next to the policy. This symbol indicates that there are unsaved or unpublished changes. To review these changes before publishing them, click the View pending changes link.
The group is added to the list of available groups on the Groups & Configs page. Edit a group To edit a group, do the following: 1 On the Groups & Configs page, click the icon. 2 In the Editing Default Policy group dialog box, edit the group information such as Group Name and Description. 3 In the Registration tab, edit the group token. NOTE: The devices can be registered to a group by entering the group token which is available on the device registration screen. 4 Click Save.
Configure a group level policy To configure a group level policy or multilevel group polices, do the following: 1 In the Groups & Configs page, go to a group where you want to configure the policy, and click Edit Policies. 2 From the drop-down menu, select the device type you want to configure. The policy settings of the device type are displayed. 3 Select a policy setting and then click Configure this item. 4 Click Save and Publish.
• From an exported file—Browse the .json file. Policies from that file are copied to the current group 4 Click Next. 5 Select the device type configurations to import. The following options are available: • All device type policies—All configured device type policies are imported to the current group. • 6 Specific device type policies—Select one or more device types from the dropdown list. Only the selected device type policies are imported to the current group. Click Next.
The Groups & Configs page is displayed. 2 Click the Edit Policies drop-down menu. 3 Click ThinOS. The Select ThinOS Configuration Mode window is displayed. 4 Select your preferred mode to configure the policy settings. The available modes are: • Wizard Mode • Advanced Configuration Mode NOTE: To set the ThinOS Advanced Configuration as the default mode, select the check box. 5 After configuring the policy settings, click Save and Publish.
• Setup Timezone • Setup General Settings • Setup Broker • Click Next to go to policy settings. • Click Back to view the previous policy settings. • Click Cancel to go back to the Groups & Configs page. • Click Save & Publish to save the changes. • Click Continue to go to ThinOS advanced configuration mode. Configuring setup security settings Use this page to configure the thin client security settings, such as user privilege and certificate installation.
Option Description Enable VNC Select this option to enable Virtual Network Computing (VNC) shadowing. VNC shadowing is the process which allows you to remotely share the same session as the user, see what the user sees, and assist with applications or session specific issues. VNC Password Enables you to set the VNC password. The password can contain a maximum of 16 characters. Encrypt Password (8.5+) Select this option to encrypt the password.
Table 6. Configuring visual experience Option Description Classic Desktop vs Zero Launchpad Select this option to define the desktop experience. NOTE: Zero Launchpad is recommended for ThinOS Lite/ Xenith devices, and for full screen sessions. Classic Desktop is recommended for seamless applications. Enable Logon Main Menu (8.5+) Select this option to enable the logon main menu. Action after all session exit Select this option to define the action after you close the last active session.
Table 9. Firmware upgrade Option Description Disable Live Upgrade Live Upgrade enables the thin client immediately after download and applies the new firmware based on defined policies. If you prefer that the thin client should only check for new firmware on each boot, then disable the Live Upgrade feature. Define desired platform or firmware mappings This option maps the specific firmware versions to different platform types.
Option Description Citrix custom store name Enter the citrix store name for the citrix StoreFront connection. This option is applicable only for Citrix. Sessions to connect automatically Select this option to automatically connect to the session. NOTE: The name of the desktop or application is case sensitive. Use a semicolon to separate the multiple sessions which must be initialized automatically. Reconnect At Logon From the drop-down menu, select your preferred option.
• Advanced Device Configuration • Remote Connection (Legacy) • Remote Connection (8.5+) • Printers (8.5+) • Network Settings (8.5+) 3 Click Save & Publish to save your changes. 4 Click Remove Policy to go back to the ThinOS page. 5 Click Cancel to go back to the Groups & Configs page.
Option Description Inactive Select this option to restart or shut down the system depending on the option you have selected from the Action after All Sessions Exit drop-down list in the Visual Experience policy setting for the ThinOS devices. Enter the time value in minutes. The range of inactive time is 0–480 seconds.
Option Description network bandwidth is not large enough to play the audio smoothly. The available options are: • • 1—ThinOS buffers at least 10 ms of audio data when playing audio. 50—ThinOS buffers at least 500 ms (0.5s) of audio data when playing audio. EnableSpeaker Select this option to enable the internal loud speaker. Playback Device Enter the playback device name. Recording Device Enter the recording device name. Mic Gain Device Enter the device name on which you want the mic gain.
Option Description Domain List (8.5+) Enter the list of domains mentioned on the sign-on window. Use a semi-colon to separate the domain name. Remember last user name and/or domain at reboot/shutdown Select this option to store the user name or domain when the system is restarted or turned off. Table 20. Configuring timezone settings Option Description Manually Set TimeZone Select the check box to override the system preference menu settings.
Option Description • Low—All settings are enabled on the local client. Show Display Settings (8.5+) Select this option to configure the display settings. From the dropdown menu, select a group to set the configuration access. Enable Keyboard and Mouse Settings (8.5+) Select this option to configure the keyboard and mouse settings. Disable Date and Time Settings (8.5+) Select this option to configure the date and time settings. Network location to upload (8.
Table 25. Configuring security policy Option Description Security Policy (8.5+) From the Security Policy (8.5+) drop-down menu, select the global security mode for SSL connection. Secured Network Protocol (8.5+) Select this option to secure the network protocol. The unsecure network protocols are disabled. TLS Minimum Version (8.5+) Select this option to choose the minimum version of SSL connection for the ThinOS devices. TLS Maximum Version (8.
Configuring keyboard settings Use the Keyboard Settings page to configure the keyboard layouts, and the behavior of keyboard shortcuts for ThinOS 8.5 and later version devices. Table 28. Configuring keyboard settings Option Description Character Set Select this option to set an appropriate character set. From the drop-down list, select your preferred character set. Keyboard Layout Select this option to set an appropriate keyboard layout. From the drop-down list, select your preferred keyboard layout.
Option Description Multi Monitor Support This option is enabled if you select Enable multiple monitors in the Monitors drop-down list. Click + Add Item to configure the multiple monitor setup. Main Screen Select this option to access the main screen. From the Main Screen drop-down menu, select your preferred screen ID. For the dual monitor mode, you must select either Screen 1 or Screen 2. Alignment Select this option to align the monitor screen.
Option Description Monitor Refresh Rate (8.5+) Select this option to set the refresh rate for your monitor. From the drop-down menu, select the appropriate refresh rate for your monitor. Table 32. Configuring multi-touch settings Option Description Multi-touch Select this option to enable multi-touch support on Dell P2418HT and ELO touch monitors. Multi-touch is not supported on local ThinOS UI and only works with RDP connections. Table 33.
Option Description • Wyse default wallpaper (8.6+) NOTE: When you select the Enable wallpaper option, the wallpaper file and wallpaper layout is displayed. Company Logo Displays the logo on the device login screen. When you select this check box, the Logo File drop-down menu is displayed. You can upload the logo file from the file repository inventory. EULA at login Displays the end-user license agreement at each login. When you select this check box, the EULA file drop-down menu is displayed.
Option Description • • Shut down the system automatically Restart the system automatically. Schedule shutdown or reboot settings Use the Schedule Shutdown/Reboot (8.5+) page to configure a scheduled restart or shutdown for ThinOS 8.5 and later version devices. Table 36. Schedule shut down or reboot Option Description Scheduled Reboot Select the check box to specify the time or day to schedule a system restart.
Table 38. System configuration Option Description Enable Audio Select this check box to enable the audio device. Enable OSD Select this check box to enable Object Storage Device (OSD) user interface. This option is supported only on Wyse 5470 All-in-One thin client. Configure MAC Pass through From the drop-down list select the option to allow the computer to enable or disable MAC Pass through function.
Option Description NOTE: The USB keyboard and the mouse always work in the BIOS setup irrespective of this setting. Enable USB Boot Support Select this check box to enable the USB boot setup. This option enables you to boot any type of USB mass storage devices. Table 43. Configuring power management settings Option Description AC Recovery From the drop-down list, select an option to specify how the system must behave when the AC power is restored.
Option Description Skip Local Firmware Check Select this option to enable the thin client to bypass the local file server checks for the firmware updates. NOTE: Dell recommends that you enable this option if you define a firmware on the management console. It leads to an endless restart as the thin client applies differing images, if you have firmware policies in the management console and firmware on a local file server. Verify Signature Select the check box to verify the signature.
Option Description • Enable selective manual overrides—Select this option to manually override the selected devices with specific client configurations. Monitor Select this option to manually override the monitor settings. This option is applicable if you have selected the Enable selective manual overrides option. Mouse Select this option to manually override the mouse settings. This option is applicable if you have selected the Enable selective manual overrides option.
Configuring central configuration settings Use the Central Configuration page to specify a file server where the ThinOS thin clients checks for configuration and image updates. Table 49. Central configuration Option Description File Server/Path Enter the full path of folder that contains the wnos file. Supported protocols include ftp, http, and https. The default protocol is ftp. User Enter the user name to access the file server. Password Enter the password to access the file server.
Option Description Broker Server Enter the broker server host name or IP address. Citrix StoreFront Select this option to enable the Citrix StoreFront based layout of published applications and desktops on the device. This option is applicable only for Citrix. Display on Desktop From the drop-down list, select an option that you want to display on the desktop. This option is applicable only for Citrix. Automatically Connect to sessions Select this option to automatically connect to the session.
Option Description • • Play on remote computer Do not Play Table 53. Session behavior defaults Option Description Font Smoothing Select this option to enable font smoothing. Font smoothing is a method to obtain sharper fonts in low resolution screens. Advanced RDP protocol features Select this option to configure the features of an RDP protocol. Default color depth for connections Select this option to set the color depth for your connection.
Option Description • • • • Enable Session Reliability Enable progressive Display Enable ICA Ping Offscreen support Table 55. Configuring peripheral behavior Option Description Auto-connect selected local Select this option to automatically connect the following peripherals: • • • • Enable USB storage disks Select this option to enable USB storage disks.
Option Description Access Gateway authentication method From the drop-down list, select the method to access the gateway authentication. Use HTTP for browsing Select this option to enable HTTP for browsing. This option is applicable only for Citrix. Alternate address via firewall Select this option to enable an alternate address through firewall. This option is applicable only for Citrix. System Menu Select this option to set the system menu. This option is applicable only for Citrix.
Option Description • Enable Whitelist or Disable Blacklist Others Use this option to enable whitelist or disable blacklist. By default, Do not enable whitelist or blacklist is selected. NOTE: The device restarts when you enable this option. The following options are displayed when you select Enable whitelist or Enable blacklist: • • • Class USB Class Vendor ID Table 58.
Option Description Interface Redirect Select this option to enable the interface redirection option. Configuring third party authentication settings Use Third party authentication settings page to configure Single Sign-On (SSO) authentication settings for ThinOS 8.5 and later version devices. Table 60. Configuring authentication settings Option Description Authentication Mode Select this option to specify the authentication mode.
Option Description Enable Windows Authentication Select this option to enable Windows authentication. If enabled, the OneSign sign fails. Sign in to the predefined broker with Windows credentials. Auto-Access From the drop-down menu, select your preferred option. Net BIOS Domain Name Select this option to enable the Net BIOS domain name option. If enabled, the Net BIOS domain name is listed in the imprivata domain list. Suspend Action From the drop-down menu, select your preferred option.
Table 65. Configuring HealthCast settings Option Description HealthCast Server Enter the name of the HealthCast server. You can use single signon authentication with Web or desktop applications. The server authenticates the user information. HealthCast Security Mode From the drop-down menu, select your preferred option.
Option Description Reconnect At Logon From the drop-down menu, select your preferred option. You can reconnect to both disconnected and active sessions. HTTPS User Agent (8.6+) Enter the INI parameter to enable communication with your client using NetScalar Session policy. Timeout From the drop-down list, select the time duration for the device to establish a connection. If the connection is not successful after the specified period of time, the device reports that the broker is not reachable.
Option Description Map USB disks to From the drop-down list, select the disk space to assign to the USB. Session Window Behavior Select this option to define whether the remote connection should be launched in a full screen mode. Select either Full Screen or Window mode. NOTE: Zero launchpad mode only supports full screen sessions. Window mode starts on a single screen while the full screen session spans across both monitors.
Option Description NOTE: The name of the desktop or application is case sensitive. Use a semicolon to separate the multiple sessions which must be initialized automatically. Configuring VMware settings Use the VMware Settings page to configure the VDI global settings for PCoIP connections on ThinOS 8.5 and later version devices. Table 72. Basic settings Option Description USB Redirection Technology Select this option to enable USB redirection.
Configuring Microsoft RDP connection settings Use the Microsoft RDP Settings page to configure the Microsoft RDP connection settings for ThinOS 8.5 and later version devices. Table 74. Configuring basic settings Option Description Enable NLA Select this option to enable Network Level Authentication. User authentication is required to establish a connection with the server. Enable Recording Select this option to enable recording.
Option Description Auto-Detect Network Select this option to automatically detect the terminal server gateway. Enable RDP H.264 Select this option to enable the H.264 encoding process for the RDP connections. Configuring vWorkspace broker connection settings Use the vWorkspace Broker connection settings page to configure the vWorkspace broker connection settings for ThinOS 8.5 and later version devices. Table 77.
Configuring direct RDP connection settings Use the Direct RDP Connection settings page to configure the RDP connections which can be accessed ThinOS 8.5 and later version devices. Table 79. Configuring basic settings Option Description Connection Name Enter the name of the connection with a maximum of 38 characters. User Name Enter the user name for the application login. Host Name or IP Address Enter the host name or IP address of the connection.
Table 81. Configuring session settings Option Description Audio Playback This option helps you to define how audio must be played in the remote session. From the drop-down menu, select any one of the following options: • • • Do not Play Play Locally Play on remote RDP Audio Recording Select this option to record the audio remotely. Default color depth for the connections Select this option to define the screen color depth of the connection. Table 82.
Configuring direct ICA connection settings Use the Direct ICA Connection settings page to configure the ICA connections which can be accessed on the ThinOS 8.5 and later version devises. Table 84. Configuring basic settings Option Description Connection Name Enter the name of the connection with a maximum of 38 characters. User Name Enter the user name for the application login. Password Enter the password for the application login. NOTE: The password is not encrypted.
Table 87. Configuring logon settings Option Description Logon Mode Select this option to select the log in mode. Start Command Application Enter the start command application. Start Command Working Directory Enter the start command working directory. Table 88. Configuring session settings Option Description Audio Quality Select this option to set the audio quality. Alternate address via firewall Select this option to enable an alternate address through the firewall.
Option Description • • Local Printer LPD printer SMB printer From the drop-down menu select the local printer connection. Table 91. Configuring printer settings Option Description Name Enter the name of the shared printer. LocalName This option is applicable only for LPD printer. Enter the name of the printer. Host This option is applicable only for local LPD printer. Enter the IP address of the LPD service host. Queue This option is applicable only for LPD printer.
Option Description The Prefer Band configuration is used to set the priority of wireless connection band, and to select the 2.4G or 5G access point to connect. The default value is Do not prefer any band. DisableN Select the check box to disable the 802.11n mode. Disable WLAN Select this option to disable the wireless functionality. From the drop-down menu, select the preferred option.
Table 95. Configuring IEEE 802.1X settings for WPA-Enterprise and WPA2-Enterprise Option Description EAP Type From the drop-down menu, select your preferred option. FAST Type This option is applicable only for EAP-FAST[8.3]. From the dropdown menu, select your preferred option. LEAP user name This option is applicable only for EAP-LEAP. Enter the leap user name in the provided field. LEAP Password This option is applicable only for EAP-LEAP. Enter the leap password in the provided field.
Configuring LAN connections Use the LAN Connections (8.6+) page to configure the LAN connections for ThinOS 8.6 and later version devices. Table 96. Configuring IEEE 802.1X settings Option Description Network Type From the drop-down list, select the preferred option. The system automatically restarts and the changes to network type are applied. NOTE: If you make any changes to this setting, the thin client reboots. From ThinOS 8.
Option Description LEAP user name Enter the leap user name in the provided field. This option is applicable only for EAP-LEAP. LEAP Password Enter the leap password in the provided field. This option is applicable only for EAP-LEAP. Server Validate Select this check box if you want the system to validate the server connection. This option is applicable only for EAP-TLS and EAPPEAP. Server Check Select the check box to check the sever connection.
Table 97. Configuring SCEP 8.6+ settings Option Description SCEP Auto Enroll Select this option to enable automatic certificate enrolment by using the environment’s SCEP server. Auto Renewal Select this option to enable automatic certificate renewal. The thin client tries to renew the requested certificates manually or automatically through SCEP. The renewal initiated after half of the valid period of the existing certificate is expired.
Configure proxy Settings Use the Proxy (8.6+) page to configure the proxy settings for ThinOS 8.6 and later version devices. Table 98. Configuring proxy 8.6+ settings Option Description Proxy Settings Select the check box to enable the proxy settings which are saved in the non-volatile memory. Applist This list provides the information about which application uses the configured proxy.
Configuring system personalization Use the system personalization page to configure the thin client settings, such as display, keyboard, mouse, time zone, and audio options for Windows Embedded Standard devices. Table 99. Configuring display options Option Description Enable Dual Monitor Select this option to enable the dual monitor functionality. If selected, the Display Mode option is available.
Table 100. Configuring mouse, basic mouse, mouse pointer, and mouse vertical options Option Description Mouse Speed Select this option to specify the speed of the mouse pointer when moving the mouse device. Left-handed Mouse Select this option to swap the left and right-click mouse buttons. Click Lock Select this option to use the highlight or drag function without holding down the mouse button.
Option Description Microphone Volume Select this option to adjust the volume of your microphone. From the drop-down menu, select your preferred volume option. Configuring desktop experience Use this page to configure the thin client settings, such as desktop wallpaper, and desktop color for Windows Embedded Standard devices. Table 103. Configuring desktop experience Option Description Desktop Wallpaper Select this option to set a wallpaper for your desktop.
Configuring security and lockdown settings Use this page to configure the security and lockdown settings. Configuring other settings Use this page to configure the thin client settings, such as power, shared drive, and clock settings for Windows Embedded Standard devices. Table 105. Configuring appliance mode Option Description Appliance Mode Select this option to set an appropriate mode for the appliance.
Table 108. Configuring power settings when plugged-in Option Description Device Sleep Plan Select this option to set the time after which your device goes to sleep mode. From the drop-down menu, select a delay time. Dim Display Select this option to set the time after which the display is dimmed. From the drop-down menu, select a delay time. Turn Off Display Select this option to set the time after which the display is turned off. From the drop-down menu, select a delay time. Table 109.
Option Description Broker Server Select this option to list the Citrix servers. Enter the list of ICA browsers separated by commas for the connection. Published Applications Select this option to specify a published application that you want to start. Single Sign On Select this option to enable the single sign-on feature for the connection. If you enable single sign-on, use your Windows login credentials to connect to the Citrix server.
Option Description This option is enabled if you select the Connection Type as Published Applications (XenApp). Store Name Enter the Store Name of the Citrix server or the StoreFront. This option is enabled if you select the Connection Type as Server Connection (XenDesktop) or StoreFront. Authentication Methods Select this option to enable the authentication type.
Option Description • Prompt Logon Method Table 114. Advanced settings Option Description Disable Full Screen Pop-up Select this option to disable the full screen pop-up warning. Logon—Connect to Active and Disconnected Sessions Select this option to connect to the active and disconnected sessions after you log in. Menu—Connect to Active and Disconnected Sessions Select this option to connect to active and disconnected sessions.
Option Description Login as Current User Select this option to enable the single sign-on feature for the connection. If you enable the login as current user option, use your Windows login credentials to connect to the VMware server. Username Select this option to define a user name for the VMware connection, if single sign-on is disabled. Password Select this option to define a password for the VMware connection, if single sign-on is disabled.
Configuring remote connection settings—RDP Use this page to configure the RDP connection settings, such as RD Gateway, display, and local resources settings for the Windows Embedded Standard devices. Table 117. Configuring basic settings Option Description Connection Name Select this option to define the name to identify the connection. Auto Launch Connection On Logon Select this option to enable the connection to automatically start after you log in.
Table 119. Configuring display settings Option Description Fullscreen Select this option to set the connection window in the full screen mode. After the full screen mode is enabled, from the drop-down menu, select the window size. Display Connection Bar Select this option to display the connection bar in the fullscreen mode. MultiMonitor Support Select this option to enable the multi-monitor support. Screen Color Depth (in bits) Select this option to define the screen color depth of the connection.
Table 121. Configuring local resources Option Description Redirect Clipboard Select this option to use the local clipboard of the device in the remote connection. Redirect COM Ports Select this option to use the local COM (serial) ports of the device in the remote connection. Redirect DirectX Select this option to redirect DirectX on the client computer and make it available in the remote connection. Redirect Drives Select this option to use the local drives of the device in the remote connection.
Table 123. Internet Explorer (IE) favorites and trusted site settings Option Description IE Favorite Select this option to add your favorite and trusted sites. Perform the following steps to add your favorite and trusted sites: 1 2 Click Add Site, and enter the folder name, URL, and description. Click Create Shortcut to create a shortcut for the site. 3 Click Remove to delete a site from the list. NOTE: URL must begin with Https:// when the Trusted Sites check box is selected.
Option Description • • • • • Disabled: Port is disabled. COM1: Port is configured at 3F8h with IRQ 4. COM2: Port is configured at 2F8h with IRQ 3. COM3: Port is configured at 3F8h with IRQ 4. COM4: Port is configured at 2F8h with IRQ 3. Sound Device Select this check box to enable the sound device. Microphone Select this check box to enable the microphone. Speaker Select this check box to enable the speakers. Table 128.
Table 133. Configuring auto-on settings Option Description Auto On From the drop-down list, set the time of the day you want the system to turn on automatically. Table 134. Configuring reboot schedule Option Description Reboot Option Some BIOS settings requires the system to restart. From the dropdown list, select one of the following options: • • Reboot immediately—The system restarts immediately. Reboot later—Select the Reboot Hour and Reboot Minute to set the system restart time.
Table 139. Configuring reboot schedule Option Description Reboot Option Some BIOS settings requires the system to restart. From the dropdown list, select one of the following options: • • Reboot immediately—The system restarts immediately. Reboot later—Select the Reboot Hour and Reboot Minute to set the system restart time. • Do not reboot—The system does not restarts. Table 140.
Configuring Wyse Easy Setup settings Use the Wyse Easy Setup page to configure the Wyse Easy Setup settings for the control panel and the user interface. Table 143. Configuring system Option Description Region & Language Enables the user to access the region and language option in the control panel. Date & Time Enables the user to access the date and time option in the control panel. Display Enables the user to access the display option in the control panel.
Option Description App State Retry Interval Enter the time interval for two successive attempts to open the application in the Wyse Easy Setup shell. Table 146. Personalization Option Description Background From the drop-down menu, select the preferred graphic image. The image should be uploaded to the file repository and displayed as a wallpaper. Logo From the drop-down list, select the logo files which are uploaded in Apps & Data > File Repository > Inventory. Table 147.
Table 149. Configuring VNC Option Description Enable VNC Select this option to enable the VNC Server. VNC User Prompt If you select this option, you must accept or decline the VNC shadowing VNC User Required Password Select this option to set the VNC password. VNC Primary Password Select this option to change the VNC password. Enter the new password with a maximum of eight characters. VNC View-only Password Enables you to work on view-only mode if you login using this password.
Option Description • • • • Disabled: Port is disabled. AT: Port is configured for IBM AT compatibility. PS2: Port is configured for IBM PS2 compatibility. ECP: Port is configured for extended capability port protocol. NOTE: This option is available for Wyse 5070 Extended thin client when the add-on card is installed. Serial Port 1 From the drop-down list, select the option to determine how the serial port on the docking station operates.
Option Description Rear port Bottom Right Select this option to enable the bottom right USB port on the back of the thin client. Table 153. Configuring security settings Option Description Enable Admin Setup Lockout Select this option to prevent others from entering the setup when an administrator password is set. Table 154. Configuring power management settings Option Description Wake On LAN From the drop-down list, select any option to allow the thin client to power up from the OFF state.
Table 158. System configuration Option Description Enable Audio Select this check box to enable the audio device. Enable Microphone Select this check box to enable the microphone. Enable Internal Speaker Select this check box to enable the internal speaker. On Screen Buttons Select this check box to enable the on-screen buttons. SATA-0 Select this check box to enable SATA-0. Integrated NIC From the drop-down list, select the option to control the on-board LAN controller.
Table 162. Configuring power management settings Option Description Wake On LAN From the drop-down list, select any option to enable the thin client to power up from the OFF state. You can trigger a thin client to power up from the OFF state by using a LAN signal. AC Recovery From the drop-down list, select any option to specify how the system operates when the AC power is restored. Table 163.
Edit the Linux policy settings To edit the Linux policy settings, do the following: 1 Click Groups & Configs. The Groups & Configs page is displayed. 2 Click the Edit Policies drop-down menu. 3 Click Linux. The Linux page is displayed.
Option Description System Language Select this option to set the language for the system. From the drop-down list, select your preferred option. Mouse Speed Select this option to specify the speed of the mouse pointer when moving the mouse. The range of mouse speed is 0–6. Left-handed Mouse Select this option to set the mouse orientation to the left position. If this check box is not selected, the mouse orientation is set to the right position.
Option Description • • • • • • • • • Show Panel Main Menu Show Panel Main Menu list Display Run Command window Activate Screensaver Show Desktop Switch between open windows Toggle current active window between full screen and normal mode Display menu options for current window Print screen—Take a screenshot Configuring login experience settings Use this page to configure the settings, such as auto login, login banner message, and passwords for admin, thin user, and root users. Table 170.
Table 171. Configuring network settings Option Description Wireless Connection Name Enter the name of the connection. SSID Enter the name of the Service Set Identifier (SSID) connection. Security Mode From the drop-down menu, select the type of security mode based on your requirement. Enter the security mode details in the respective fields. Configuring security settings Use this page to configure the security options. Table 172.
Option Description • Deny All Excluding HID—Allows USB ports to be accessed expect the human interface devices such as mouse, keyboard and so on. • Deny Class—Allows only specific USB ports classified as Deny class will not be accessed. Configuring central configuration settings Use this page to enter the file server, firmware server, root path, and the corresponding user credentials. Table 173.
Table 174. Configuring other settings Option Description Auto Power-On Select this option to enable the system to boot up when power is restored without waiting for the user to press the power button. Power Button Action From the drop-down menu, select any one of the option to specify the default action to be performed when you press the power button. • • • • Interactive Restart Shutdown None DHCP Vendor ID Select this option to change the DHCP Vendor ID. The default Vendor ID is wyse-5000.
Option Description Audio Bandwidth Limit Select this option to set the bandwidth used for audio input. From the drop-down menu, select any one of the following options: • • • Low Medium High Enable UDP Audio Select this option to enable the transport of audio data through UDP. Flash Redirection Policy Select this option to set the Flash Redirection policy. From the drop-down menu, select either allow or deny the Flash Redirection policy.
Table 178. Configuring VMware USB redirection Option Description Enable USB Redirection Select this option to enable VMware USB Redirection to all the devices. You can specify which devices and device families can be allowed or denied through the USB redirection policy in to the VMware sessions. Configuring remote connection settings—Citrix Use this page to create a Citrix broker connection. Configuration settings for the Citrix connection vary based on the connection type. Table 179.
Option Description Low Bandwidth Select this option to set the slow bandwidth optimization. Enable Sound Select this option to enable sound. SmartCard Login Select this option to enable the smart card login feature for ICA connection. Encryption Level Select this option to set an encryption level. From the drop-down menu, select any one of the following encryption levels: • • • • • Windows Size Select this option to set a window size.
Table 180. Configuring remote connection VMware Option Description Connection Name Select this option to enter a name to identify the connection. Auto Launch Connection On Logon Select this option to automatically launch the connection after you log in. VMWare Server Address Enter the hostname or the IP address of the VMware View server. VMWare Server Port Number Enter the port number of the host. Use Secure Connection (SSL) Select this option to use the SSL connection.
Option Description Auto Reconnect Select this option to enable the thin client to reconnect to the VMware session automatically. Delay before trying to reconnect Enter the time in seconds to delay the reconnection attempt. When you select the Auto Reconnect check box, this option is displayed. Username with domain Select this option to associate a username with the domain. Unauthenticated Access Select this option to prevent any unauthenticated access the application.
Option Description • • • 1280 x 1024 1600 x 1200 Full Screen Forward All Printers Select this option to forward all the printers to the remote connection. Auto Reconnect Select this option to enable the thin client to reconnect to the RDP session automatically. Delay before trying to reconnect Enter the time in seconds to delay the reconnection attempt. When you select the Auto Reconnect check box, this option is displayed. Drive Mapping Select this option to map drives on the RDP session.
Configuring remote connection settings—Browser Use this page to configure the remote connections browser. Table 182. Configuring remote connection settings—Browser Option Description Connection Name Enter the name to identify the connection. Auto launch Connection on Logon Select this option to automatically launch the connection during login. URL Enter the starting URL. Kiosk Mode Select this option to enable the kiosk mode. Window Size Select this option to set a window size.
4 • Network • Security • Central Configuration • Other settings • VDI Global Settings • Remote Connections Citrix • Remote Connections VMware • Remote Connections RDP • Remote Connections Browser • Advanced Settings • Device Info • BIOS ThinLinux 3040 Settings • BIOS ThinLinux 5070 Settings • Proxy Settings After configuring the policy settings, click Save and Publish. Configuring system personalization Use the System Personalization page to configure the system personalization.
Option Description Time Servers (NTP Servers) Select this option to list the time servers. Time severs allow the NTP server to synchronize the time. Multiple servers are allowed, and the server names must be separated by commas. Table 188. Configuring audio settings Option Description Audio Volume Select this option to set the audio volume of the thin client. The range of the audio volume is 0–100. Audio Mute Select this option to set the thin client to mute mode.
Configure hot keys for following actions: • Minimize current active window • Maximize/Unmaximize current active window • Unmaximize current active window • Resize current active window • Move current active window • Show Desktop • Switch between open windows • Toggle current active window between full screen and normal mode • Print screen (Take a screenshot), you can select the check box to enable or disable the print screen option.
Configuring security settings Use this page to configure the security policy settings. Table 193. Configuring USB Rule Option Description USB Lockdown From the drop-down list, select any of the following options to restrict the use of USB ports: • • • • Allow All Deny All Deny All Excluding HID Deny Class—Based on the USB class you can deny access to USB device. NOTE: This setting is supported on thin clients running ThinLinux 2.1 and later versions.
Option Description From the drop-down menu, select the certificates which are added in the file repository. Table 196. Configuring SSH settings Option Description Enable SSH Select this option to enable Secure Shell (SSH) on the device. Allow “root” SSH login Select this option to enable the root SSH login. Table 197. Configuring VNC settings Option Description Enable VNC Server Select this option to enable the VNC Server.
Option Description Delayed Update Server Password Enter the password to access delayed update server. Delayed Update Mode Select this option to set the update mode for delayed update process. Reset to factory defaults Select this option to set the device to the factory default condition after the imaging process. Allow base image downgrade Select this option to enable the base image downgrade. Configuring other settings Use this page to configure the other options. Table 199.
Option Description NOTE: This option is applicable to thin clients running ThinLinux 2.1 and later versions. Table 201. Configuring Citrix general settings Option Description ICA Browsing Protocol Select this option to set the default browsing protocol. ICA PAM Login Select this option to configure the PAM login. Browser IP Enter the browser IP address. Store Name Specify the store name. Domain Name Enter the domain name.
Option Description Use Alternate Address Select this option to use an alternate IP address from the ICA master browser to pass firewalls. ICA Proxy Type Select this option to choose the proxy type for the ICA connection. The default value is None. Table 202. Configuring Citrix USB redirection settings Option Description Allow USB Redirection of devices plugged in before ICA Session start Select this check box for ICA Desktop Appliance Mode.
Option Description • • Published Application Store Front Connection Server Select this option to enter the IP address or FQDN of the Citrix server. Citrix Server FQDN or IP address Select this option to enter the Citrix server FQDN or IP address. This is applicable for Published Application and StoreFront connection type. Published Application Select this option to specify a published application to start. This is applicable for Published Application and StoreFront connection type.
Option Description Screen Color Depth Select this option to set a screen color depth. From the drop-down menu, select any one of the following options: • • • 64K 256 16M Auto Reconnect Select this option to enable the thin client to reconnect to the Citrix session automatically. Delay before trying to reconnect Select this option to set the time in seconds to delay the reconnecting attempt. When you select the Auto Reconnect check box, this option is displayed.
Option Description Enable MMR Select this option to enable MMR in VMWare View connection settings. NOTE: This option is supported on thin clients running ThinLinux 2.1 and later versions. Interactive Mode Select this option to enable interactive connection mode. NOTE: This option is supported on thin clients running ThinLinux 2.1 and later versions.
Option Description Domain name Enter the domain name. Enable NLA Select this option to enable Network Level Authentication. When the RDP option is set as protocol, this option is displayed. Username Enter the user name when the PCoIP protocol is selected. Password Enter the password when the PCoIP protocol is selected. Domain Name Enter the domain name. Interactive Mode Select this option to enable the User Interactive mode.
Table 207. Configuring remote connection settings—RDP Option Description Connection Name Select this option to enter the name to identify the connection. Auto Launch Connection on Logon Select this option to automatically launch the connection after you log in. Server Address Enter the server name or the IP address. SmartCard Login Select this option to enable the smart card authentication. Use Network Level Authentication (NLA) Select this option to enable the Network Level authentication.
Option Description NOTE: This option is supported on thin clients running ThinLinux 2.1 and later versions. Compression Select this option to compress the signal. NOTE: This option is supported on thin clients running ThinLinux 2.1 and later versions. Low Bandwidth Select this option to lower the bandwidth value. NOTE: This option is supported on thin clients running ThinLinux 2.1 and later versions.
Table 209. Configuring remote connection settings—Browser Option Description Connection Name Enter the name to identify the connection. Auto launch Connection on Logon Select this option to automatically launch the connection during login. URL Enter the starting URL. Kiosk Mode Select this option to enable the kiosk mode. RC Disable Panel in kiosk mode Select this option to disable the RC panel in the kiosk mode. Window Size Select this option to set a window size.
Table 212. Configure general settings Option Description Device Notes Enter the device notes in the provided field. For example, property ownership tag. Table 213. Configure system settings Option Description Enable UEFI Network Stack Select this check box to enable UEFI Network Stack. The networking protocols are installed and the pre-OS and early OS networking features are made available to use any enabled NICs. Integrated NIC From the drop-down list, select the preferred option.
Table 217. Configure BIOS Admin password settings Option Description Enable Admin Password Select this check box to enable the BIOS administrator password. Successful changes to this password take effect immediately. Admin Password Enter the new BIOS administrator password. This option is available only if you select the Enable Admin Password check box. Table 218.
Configuring BIOS settings for Wyse 5070 thin client with ThinLinux Use the BIOS settings page to configure the BIOS settings for Wyse 5070 thin client with ThinLinux. Table 222. Configure general settings Option Description Device Notes Enter the device notes in the provided field. For example, property ownership tag. Table 223. Configure system settings Option Description Enable Audio Select this check box to enable the audio device.
Table 224. Configure USB settings Option Description Enable USB Boot Support Select this check box to enable the USB boot setup. Allows you to boot any type of USB Mass Storage Devices. Enable Front USB Ports Select this check box to enable the device attached to the front USB port. If you select this check box, the device is detected by the operating system. However, if the USB port is disabled, the operating system cannot detect the device attached to the front USB port.
Option Description Extend BIOS POST Time From the drop-down list, select a delay time to see the post status messages. Table 228. Configure wireless settings Option Description WLAN/WiGig Select this check box to enable the internal wireless devices. Bluetooth Select this check box to enable Bluetooth devices. Table 229. Configure BIOS administrator password Option Description Enable administrator Password Select this check box to enable the BIOS administrator password.
Option Description Proxy Method From the drop-down list, select your preferred proxy method. The available options are: • • • • • None AutoDetect Manual Proxy Config System proxy NOTE: • • When you configure and apply the settings, you will be prompted to close the Firefox browser on the thin client. To clear the old configurations you must select the option None from the Proxy Method drop-down list and push the configuration.
Option Description NOTE: This setting is supported on thin clients running ThinLinux version 2.1 and later versions. Automatic Proxy URL Enter the configuration URL address. This option is enabled if you select the Proxy Method as Automatic. Multi Proxy Settings Use this option to configure one or more proxy server settings. This option is enabled if you select the Proxy Method as Manual.
Option Description Time zone From the drop-down list, select the time zone of the system. Enable DayLight Savings Select the check box to enable the Daylight Saving Time (DST) feature. Configuring language settings Use the Language page to configure the language settings. Table 236. Configure language settings Option Description Language From the language drop-down list, select the language for Object Storage Device (OSD) user interface.
Option Description network bandwidth is constrained, select Reduced to enable higher frame rates. Select towards Perception-Free to enable higher image quality. When network bandwidth is not constrained, the PCoIP system maintains perception-free quality regardless of the Minimum Image Quality parameter. Note: The Maximum Initial Image Quality must be greater than or equal to the Minimum Image Quality.
Table 240. Upload certificate Option Description Certificates Select the required check box to upload the certificate. Clear the check box to delete an uploaded certificate. The list of certificates uploaded on the File Repository Inventory page is displayed. The certificates are deleted after you restart the device. You can only upload .pem files. Table 241.
Table 244. Upgrading firmware settings Option Description Enable live upgrade Select this option to enable the live upgrade process. This feature allows you to download and apply the firmware immediately after downloading. The system automatically restarts and the changes to Enable live upgrade are applied. If you disable this feature, the firmware is downloaded to the system but not installed. The system waits till next restart to apply the firmware.
Option Description Logon Password Enter the password of the client. The password must be a maximum of 128 characters. This option is applicable when the connection types are View Connection Server or PCoIP Connection Server, and the session type is Auto-Logon. Logon Domain Name Enter the domain name of the thin client. The domain name must be a maximum of 256 characters.
Option Description This option is applicable when the connection type is View Connection Server and the session type is Imprivata OneSign Certificate Check Mode From the drop-down list, select the level of verification performed on the certificate provided by the connection server. This option is applicable when the connection type is PCoIP Connection Server. Certificate Check Mode Lockout Select this option if required. This option is applicable when the connection type is PCoIP Connection Server.
Configuring system personalization Use this page to configure the thin client display settings, such as resolution, color depth, dual monitor, time zone, mouse, and audio options for Wyse software devices. Table 248. Configuring display options Option Description Enable Dual Monitor Select this option to enable the dual monitor functionality. Monitor Resolution (Primary) Select this option to set the resolution of your monitor. From the drop-down menu, select the appropriate resolution.
Option Description MS Gina Keyboard Layout Select this option to view the Keyboard Selection screen on the Windows login screen. MS Gina Keyboard Layout feature allows to choose desired language and keyboard layout in the Windows devices on the login screen. For example, If the Windows credential is in Non-English and the keyboard attached to the Windows system is English.
Option Description NOTE: You can press the Ctrl key on your keyboard to locate the mouse pointer when it is not in motion. Hide Mouse Pointer Select this option to hide the mouse pointer when it is stationary. NOTE: To locate the mouse pointer when it is stationary, press the Ctrl key. Pointer Trail Length Select this option to define the length of the pointer trail when the mouse pointer is in motion.
Configuring desktop experience Use this page to configure the thin client settings, such as desktop wallpaper, and desktop color for Wyse software devices. Table 257. Configuring desktop experience Option Description Desktop Wallpaper Select this option to set a wallpaper for your desktop. After you enable the desktop wallpaper option, do the following: • From the Wallpaper File drop-down list, select a wallpaper for your desktop.
Configuring security and lockdown settings Use this page to configure the security and lockdown settings. Table 259. Security and lockdown Option Description Install Certificates Select this option to view the certificates that are uploaded to the file repository. Disable USB Storage Device Access Select this option to enable or disable the USB mass storage device access for non-administrator users.
Table 262. Power settings on battery Option Description Device Sleep Plan (on battery) Select this option to set the time after which your device goes to sleep mode. From the drop-down menu, select a delay time. Dim Display (on battery) Select this option to set the time after which the display is dimmed. From the drop-down menu, select a delay time. Turn Off Display (on battery) Select this option to set the time after which the display is turned off. From the drop-down list, select a delay time.
Configuring remote connection settings—Citrix Use this page to configure the Citrix remote connection which can be accessed on the Wyse software thin client. Table 266. Basic options Option Description Connection Name Select this option to set a name for connection identification. Auto Launch Connection On Logon Select this option to enable the connection to automatically start the session after you log in. Connection Type Select this option to set a connection type.
Option Description • User Key Combos Passthrough Off Select this option to specify a window to apply the Windows user key combinations. • Default User Key Combos Passthrough • On the local desktop • On the remote desktop • In full screen desktops only Store Name Enter the Store Name of the Citrix server or the StoreFront. Authentication Methods Select this option to enable the authentication type.
Table 268. Server options Option Description Logon Method Select this option to choose a logon method for your Citrix connection. • Default Logon Method • Prompt Logon Method Table 269. Advanced settings Option Description Disable Full Screen Pop-up Select this option to disable the full screen pop-up warning. Logon—Connect to Active and Disconnected Sessions Select this option to connect to the active and disconnected sessions after you log in.
Option Description Protocol Select this option to choose the protocol for the VMware connection. From the drop-down menu, select either of the following options: • PCOIP • • RDP Blast Login as Current User Select this option to enable the single sign-on feature for the connection. If you enable the login as current user option, use your Windows login credentials to connect to the VMware server.
Option Description Username Select this option to define a user name for the connection, if single sign-on is disabled. Password Select this option to define a password for the connection, if single sign-on is disabled. Domain Name Select this option to define a domain name for the connection. Auto Reconnect Select this option to enable the connection to automatically reconnect, if the connection is dropped. Table 273.
Option Description • RDP 32–Bit Highest Quality Table 275. Configuring other Settings—Local and Parameter Option Description Remote Audio Play Back Select this option to manage the audio playback in the remote connection. Enable Remote Audio Recording Select this option to record the audio remotely. Apply Windows Keys Select this option to apply Windows keys. From the drop-down menu, select the preferred option.
Table 277. Configuring other settings—Experience Option Description Connection Speed To Optimize the Performance Select this option to specify the connection speed to optimize the performance. Desktop Background Select this option to enable the desktop background for the connection. Visual Styles Select this option to enable the visual styles for the connection. Font Smoothing Select this option to enable font smoothing for the connection.
Table 279. Configuring Internet Explorer (IE) favorites and trusted site settings Option Description IE Favorite Select this option to add your favorite and trusted sites. Perform the following steps to add your favorite and trusted sites: • • Click Add Site, and enter the folder name, URL, and description. Click Create Shortcut to create a shortcut for the site. • Click Remove to delete a site from the list. NOTE: The URL must begin with https:// when the Trusted Sites check box is selected.
Configuring Wyse Easy Setup version settings Use the Wyse Easy Setup (2.0+) page to configure the Wyse Easy Setup settings for the control panel and the user interface. Table 284. Configure system Option Description Sound Select this check box to access the sound option in the control panel. Region & Language Select this check box to access the region and language option in the control panel. Date & Time Select this check box to access the date and time option in the control panel.
Option Description App State Retry Count Enter the number of times the application should attempt to open in the Wyse Easy Setup shell. App State Retry Interval Enter the time interval for two successive attempts to open the application in the Wyse Easy Setup shell. Table 287. Configure personalization Option Description Background From the drop-down list, select the preferred graphic image. Note: Before you perform this step, you must upload the graphic images to the file repository.
Table 290. Configuring VNC settings Option Description Enable VNC Select this option to enable the VNC Server. VNC User Prompt If you select this option, you must accept or decline VNC shadowing. VNC User Required Password Select this option to set the VNC password. VNC Primary Password Select this option to change the VNC password. Enter the new password with a maximum of eight characters. VNC View-only Password Enter the primary password. You cannot edit the password.
5 Managing devices This section describes how to perform a routine device management task by using the management console. To locate the inventory of the devices, click the Devices tab. You can view a subset of the devices by using various filter criteria, such as groups or subgroups, device type, operating system type, status, subnet, platform, or time zone.
• Device compliance status • Pulling Windows Embedded Standard or ThinLinux image • Upgrading ThinLinux 1.x to 2.1 and later versions • Requesting a log file • Troubleshooting your device Methods to register devices to Wyse Management Suite You can register a thin client to the Wyse Management Suite by using any of the following methods: • Register manually through the User Interface provided by the Wyse Device Agent (WDA) on the device.
Registering Wyse Software Thin Client to Wyse Management Suite by using Wyse Device Agent Prerequisites Create a group to register a device to Wyse Management Suite. Steps 1 Open the Wyse Device Agent application. The Wyse Device Agent window is displayed. 2 Enter the device registration details. 3 From the Management Server drop-down list, select Wyse Management Suite. 4 Enter the server address and the port number in the respective fields. 5 Enter the group token.
Registering ThinLinux version 2.0 devices by using FTP INI method Create a group to register in Wyse Management Suite. 1 Create a wlx.ini file. Enter the following parameter: WMSEnable=yes\no WMSServer=https://FQDN of the WMS Server:Port GroupRegistrationKey=GroupToken present in WMS Server CAValidation=True/False For example, to register the ThinLinux version 2.0 device to Wyse Management Suite (FQDN of the server is ServerFQDN.domain.
WMSEnable=yes WMSServer=https://ServerFQDN.domain.com:443 GroupRegistrationKey=defa-defadefa CAValidation=True 2 Place the wlx ini file in the wyse\wlx folder. 3 Go to Settings and switch to admin on the ThinLinux thin client. 4 Go to Management > INI. 5 Enter the FTP server URL. 6 Click Save and then restart the thin client. 7 Go to Management > Wyse Device Agent.
Registering devices by using DHCP option tags You can register the devices by using the following DHCP option tags: NOTE: For detailed instructions on how to add DHCP option tags on the Windows server, see Creating and configuring DHCP option tags. Table 292. Registering device by using DHCP option tags Option Tag Description Name—WMS This tag points to the Wyse Management Suite server URL. For example, wmsserver.acme.com:443, where wmsserver.acme.
• Thin Linux—2.0.24 or later versions • ThinOS—8.4 firmware or later versions You can register devices with the Wyse Management Suite server if DNS SRV record fields are set with valid values. NOTE: For detailed instructions on how to add DNS SRV records on the Windows server, see Creating and configuring DNS SRV record. The following table lists the valid values for the DNS SRV records: Table 293.
URL/Tag Description NOTE: CA Validation is optional for the latest version of Wyse Management Suite. For more information on the customer security environments, see Wyse Device Agent. Searching a device using filters To search a device using filters, do the following: 1 From the Configuration Groups drop-down list, select either the default policy group or the groups which are added by an administrator.
Querying the device status To send a command to update the device information and status in the system, do the following: 1 Click Devices. The Device page is displayed. 2 Apply the filters to find the preferred device. 3 Select the check box of the device. 4 Click Query. An Alert window is displayed. 5 Click Send Command to send the query command. Locking the devices To lock the registered device, do the following: 1 Click Devices. The Device page is displayed.
NOTE: • Force unregister option can be used to remove the device when there is no communication between the server and client. The device will be moved to unmanaged state and can be removed from the server entry. • Unregister and Force unregister actions can be performed by WES WDA UI also. Resetting to factory default settings To reset your ThinOS-based devices to factory default settings, do the following: 1 Click Devices. The Device page is displayed.
4 From the More Actions drop-down menu, click Wake On LAN. An Alert window is displayed. 5 Click Send Command. Viewing device details To view the device details, do the following: 1 Click Devices. The Device page is displayed. 2 Apply the filters to find the preferred device. For more information, see Searching a device using filters. The preferred device list is displayed. 3 Click any one of the displayed devices. The Device Details page is displayed.
The Device page is displayed. 2 Apply the filters to find the preferred device. For more information, see Searching a device by using filtersSearching a device using filters. The preferred device list is displayed. 3 Click any one of the displayed devices. The Device Details page is displayed. 4 On the Device Details page, click Events tab. The events on the device is displayed. Viewing installed applications To view the installed applications on the device, do the following: 1 Click Devices.
Figure 5. Alert NOTE: A ThinLinux device does not need to be restarted to update the host name. 5 Click Send Command. A confirmation message is displayed. Configuring remote shadow connection Use this page to allow global and group administrators to access the Windows Embedded Standard, ThinLinux, and ThinOS thin client sessions remotely. This feature is applicable to only to private cloud and is available for both Standard and Pro licenses.
Figure 6. Remote Shadow(VNC) The IP address and the port number of the target thin client is displayed in the Remote Shadow (VNC) dialog box. NOTE: The default port number is 5900. 3 Change the port number of the target thin client.(optional) 4 Click Connect to initiate a remote session to the target thin client. Shutting down devices Wyse Management Suite enables you to shut down the devices such as, Windows Embedded Standard, ThinLinux, and ThinOS thin clients. 1 Click Devices.
Device compliance status By default, the following colors are displayed as the device status: • Red—when the registered device has not been checked in for more than seven days. • Gray—When you apply any configuration policy to the device. • Green—When you apply all the configuration policies to the device. The default value can be changed from 1 to 99 days. The Online Status option is located next to the device name.
When the Pull OS Image command is sent, the client device receives an image pull request from the server. An image pull request message is displayed on the client side. Click either of the following options: • Pull after sysprep—The device restarts, and logs in to the operating system in a disabled state. Run the custom sysprep. After the custom sysprep is complete, the device boots to Merlin operating system and the image pull operation is performed.
Upgrade ThinLinux 1.x to 2.x To upgrade ThinLinux by using Wyse Management Suite, do the fillowing 1 Go to www.dell.com/support. 2 Click Product Support, enter the Service Tag of your thin client, and then press Enter. NOTE: If you do not have Service Tag, manually browse for your thin client model. 3 Click Drivers and downloads. 4 From the Operating system drop-down list, select ThinLinux. 5 Scroll down the page, and do the following: • Download the Platform_util-1.0.26-0.3.x86_64.rpm, wda-2.1.
Figure 7. Log file pull NOTE: • The device must be enabled to pull the log file. • The ThinOS device uploads the system logs. • The Windows Embedded Standard uploads Wyse Device Agent logs and Windows Event viewer logs. • Linux or ThinLinux uploads Wyse Device Agent logs and system logs. • Linux or ThinLinux uploads the log file in .tar format, if you are extracting the files on Windows system then you require 7zip or any other equivalent file.
6 Apps and data This section describes how to perform routine device application tasks, operating system imaging, inventory management, and set policies by using the Wyse management console. The repository names are color coded to indicate the status. • Standard application policy—This policy allows you to install a single application package. • Advanced application policy—This policy allows you to install multiple application packages.
• • • Supports script deployments for ThinLinux devices with extensions .sh. In standard or advanced application policy if there is a script/deb/rpm which returns value other than 0 then it is considered as a failure. In advanced application policy if pre-install fails then app installation is not continued. Configuring thin client application inventory To configure the thin client inventory, do the following: 1 Click the Apps and Data tab. 2 In the left pane, go to App Inventory > Thin Client.
6 Enter the Policy Name. 7 From the drop-down list, select the Group. 8 From the drop-down list, select the Task. 9 From the drop-down list, select the OS Type. 10 Select the Filter files based on extensions checkbox to filter the applications. 11 From the drop-down list, select the Application. If the application files are available on multiple repositories, then the number of repositories is displayed next to the file name.
4 Click Add Advanced Policy. The Add Advanced App Policy page is displayed. 5 To create an application policy, do the following: a Enter the Policy Name. b From the drop-down list, select the Group. c Select the Sub Groups check box to apply the policy to sub groups. d From the drop-down list, select the Task. e From the drop-down list, select the OS Type. f Select the Filter files based on extensions check box to filter the applications.
1 In the local repository, go to softwareTcApps, and copy the application to the folder. 2 Ensure that the application is registered by navigating to the Apps & Data tab and selecting Wyse Software thin client under App Inventory. 3 Click Apps & Data. NOTE: The App Inventory interface takes approximately two minutes to populate any recently added programs. Apps & Data page is displayed. 4 In App Policies, click Wyse Software Thin Client. 5 Click Add Policy.
Creating and deploying advanced application policy to Wyse Software Thin Clients To deploy an advanced application policy to Wyse Software Thin Clients, do the following: 1 In the local repository, go to softwareTcApps, and copy the application to the folder. 2 Ensure that the application is registered by navigating to the Apps & Data tab and selecting Wyse Software thin client under App Inventory. NOTE: The App Inventory interface takes approximately two minutes to populate any recently added programs.
The application policy job can run: a Immediately—Server runs the job immediately. b On device time zone—Server creates one job for each device time zone and schedules the job to the selected date/time of the device time zone. c On selected time zone—Server creates a job that must be scheduled at the date and time of the designated time zone. 8 Click Preview and schedule on the next page to create the job. 9 You can check the status of the job by navigating to the Jobs page.
Wyse Management Suite extracts the files from the zipped folder and uploads the files in the \repository \osImages\valid location. The image extraction may take several minutes depending upon the image size. NOTE: For ThinLinux operating system, download the merlin image, for example, 1.0.7_3030LT_merlin.exe, and copy in the \Repository\osImages\zipped folder. The image is added to the repository.
7 Click Upload. NOTE: The file is added to the repository when you select the check box but it is not assigned to any of the groups or devices. To deploy the BIOS file to a device or a group of devices, go to the respective device or group configuration page. Adding Teradici firmware to repository To add a operating system image to the Teradici firmware repository, do the following: 1 In the Apps & Data tab, under OS Image Repository, click Teradici. 2 Click Add Firmware File.
Managing file repository This section allows you to view and manage the file repository inventories, such as wallpaper, logo, EULA text file, Windows wireless profile, and certificate files. To add a new file, do the following: 1 In the Apps & Data tab, under File Repository, click Inventory. 2 Click Add File. The Add File screen is displayed. 3 To select a file, click Browse and navigate to the location where your file is located.
4 Select Desktop Wallpaper. 5 From the drop-down list, select the wallpaper file. 6 Click Save and Publish. Click Jobs to check the status of configuration policy. You can click the number next to the status flag in the Details column to check devices with their status.
7 Managing rules This section describes how to add and manage the rules in the Wyse Management Suite console.
NOTE: Make sure that you have installed the pro license version of Wyse Management Suite. 1 Click the Rules tab. 2 Select the Unmanaged Device Auto Assignment option. 3 Click the Add Rules tab. 4 Enter the Name and select the Destination group. 5 Click the Add Condition option and select the conditions for assigned rules. 6 Click Save. The rule is displayed in the unmanaged group list. This rule is applied automatically and the device is listed in the destination group.
7 From the drop-down menu, select a target device to apply Notification Target and the time duration to apply Notification Frequency. 8 Click Save. Editing an alert notification rule To edit a rule for alert notification, do the following: 1 Click the Rules tab. 2 Select the Alert Notification option. 3 Click Edit Rule. An Edit Rule window is displayed. 4 From the Rule drop-down list, select a rule. 5 Enter the Description. 6 From the Groups drop-down list, select a group.
8 Managing Jobs This section describes how to schedule and manage jobs in the management console. Figure 8. Jobs In this page you can see jobs based on the following filtering options: • Configuration Groups—From the drop-down menu, select the configuration group type. • Scheduled by—From the drop-down menu, select a scheduler who performs the scheduling activity.
– Failed • Detail Status—From the drop-down menu, select the status in detail. The available options are: – 1 or more failed – 1 or more pending – 1 or more In progress – 1 or more cancelled – 1 or more completed • More Actions—From the drop-down menu, select the Sync BIOS Admin Password option.
4 – Others From the OS Type drop-down menu, select the operating system. The available options are: 5 • ThinOS • WES • Linux • Thin Linux • Wyse Software Thin Client From the Status drop-down menu, select the status of the job. The available options are: 6 • Scheduled • Running/In Progress • Completed • Cancelled • Failed From the Detail Status drop-down menu, select the status in detail.
5 Enter/select the following details: • Effective— Enter the starting and ending date. • Start between—Enter the starting and ending time. 6 • On day(s)—Select the days of the week. Click the Preview option to view the details of the scheduled job. 7 On the next page, click the Schedule option to initiate the job. Scheduling the device command job To schedule a device command job, do the following: 1 On the Jobs page, click Schedule device command job. The Device Command Job screen is displayed.
9 Managing Events This section describes how to view all events and alerts in the management system using the management console. It also provides instructions on viewing an audit of events and alerts for system auditing purposes. A summary of events and alerts is used to obtain an easy-to-read daily summary of what has happened in the system. The Audit window arranges the information into a typical audit log-view.
• Access • Registration • Configuration • Remote Commands • Management • Compliance Searching an event or alert by using filters To search an event or alert by using filters, do the following: 1 Click Events. The Events page is displayed. 2 From the Configuration Groups drop-down menu, select either the default policy group or the groups which are added by an administrator.
10 Managing users This section describes how to perform a routine user management task in the management console. The following are the two types of users: • Administrators—Wyse Management Suite administrator can be assigned the role of a global administrator, group administrator, or viewer. – A Global Administrator has access to all the Wyse Management Suite functions. – A Group Administrator has access to all assets and functions for specific groups that are assigned to them.
Figure 11. Unassigned admins NOTE: To import users from the CSV file, click Bulk Import. Topics: • Adding a new admin profile • Editing an admin profile • Deactivating an admin profile • Deleting an admin profile • Editing a user profile • Importing the CSV file Adding a new admin profile To add a new admin profile, do the following: 1 Click Users. 2 Click Administrator(s). 3 Click Add Admin. The New Admin User window is displayed.
NOTE: If you select the Administrator role as Viewer, the following administrative tasks are displayed: 2 Query Device ◦ Unregister Device ◦ Restart/Shutdown Device ◦ Change Group Assignment ◦ Remote Shadow ◦ Lock Device ◦ Wipe Device ◦ Send Message ◦ WOL Device In the Password section, do the following: a 7 ◦ b Click Save. Enter the custom password. To generate any random password, select the Generate random password radio button.
4 Click OK. Deleting an admin profile Admin must be deactivated before you delete them. To delete an admin, do the following: 1 Click Users. 2 Click Administrator(s). 3 Select the check box of a particular admin or admins which you want to delete. 4 Click Delete Admin(s). An Alert window is displayed. 5 Enter a reason for the deletion to enable the Delete link. 6 Click Delete. Editing a user profile To edit a user profile, do the following: 1 Click Users. 2 Click Unassigned Admins.
11 Portal administration This section contains a brief overview of your system administration tasks that are required to set up and maintain your system. Figure 12.
Adding the Active Directory server information To import Active Directory users on the Wyse Management Suite private cloud, do the following: 1 Log in to the Wyse Management Suite private cloud. 2 Navigate to Portal Admin > Console Settings > Active Directory (AD). 3 Click the Add AD Server Information link. 4 Enter the server details such as AD Server Name, Domain Name, Server URL, and Port. 5 Click Save. 6 Click Import. 7 Enter the user name and password.
NOTE: To import the users using LDAPS protocol, complete the following steps: 1 Import the AD Domain Server Root Certificate into Java Key Store Manually using the keytool. For example, keytool.exe> -importcert -alias "WIN-O358EA52H8H" -keystore "" -storepass changeit -file "Root Certificate Path" 2 Restart Tomcat service.
3 To setup ADFS on public cloud, see Configuring Active Directory Federation Services feature on public cloud. Alert classifications The Alert page categorizes the alerts as Critical, Warning, or Info. NOTE: To receive alerts through e-mail, select the Alert Preferences option from the username menu displayed on the upperright corner.
To use Wyse Management Suite repository, do the following: 1 Download the Wyse Management Suite repository from the public cloud console. 2 After the installation process, start the application. 3 On the Wyse Management Suite Repository page, enter the credentials to register the Wyse Management Suite repository to Wyse Management Suite server. 4 If you enable the Register to Public WMS Management Portal option, you can register the repository to Wyse Management Suite public cloud.
4 Select the CA Validation check box to enable CA validation. 5 Click Test. Enabling Two-Factor authentication You must have at least two active global administrator users in the system. Create two or more global administrators before proceeding to the task. To enable two factor authentication, do the following: 1 Log in to the Wyse Management Suite portal and click the Portal Admin tab. 2 Click Two Factor Authentication under Console Settings.
Figure 14. Types of report 4 From the Groups drop-down list, select the group. 5 Select the delimiter. 6 Click Save. Enabling multi-tenant accounts This section allows you to create an additional organization. You can manage the organizations independently. Each account must have its own license key and can set up its own set of admin accounts, policies, operating system images, application, rules, alerts, and so on. The high level operator creates these organizations.
Enabling custom branding This option allows you to add the name of your company and its logo or brand. You can upload your own header logo, favicon, add a header title, and change header colors to customize the Wyse Management Suite portal. To access and specify custom branding: 1 Go to Portal Administrator > Account > Custom Branding. 2 Click Enable Custom Branding 3 In Header Logo, click Browser and select and select the header logo image from the folder location.
Exporting licenses to Wyse Management Suite Private Cloud To export licenses to Wyse Management Suite Private Cloud from Wyse Management Suite public cloud, do the following: 1 Log in to Wyse Management Suite public cloud console. 2 Go to Portal Administration > Accounts > Subscription. 3 Enter the number of thin client seats that must be exported to Wyse Management Suite Private Cloud. 4 Click Export. 5 Copy the generated license key. 6 Log in to Wyse Management Suite Private Cloud console.
2 Click Setup under Systems. 3 Select the check box to perform server certificate validation for all device-to-server communication. 4 Enter the following details in the Update SMTP for Email Alerts area: • SMTP server • Send from address • Username • Password • Test address Current Certificate: Select the Certificate Validation check box to enable the CA validation for private cloud.
12 Configuring Wyse Easy Setup by using Wyse Management Suite You can install and configure the Wyse Easy Setup software by using Wyse Management Suite. Topics: • Installing Wyse Easy Setup • Deploying a Wyse Easy Setup configuration Installing Wyse Easy Setup Prerequisites • A minimum free disk space of 100 MB • A minimum RAM disk size of 100 MB • Microsoft Visual C++ Redistributable 2012 32–bit (x86) or 64–bit (x64) • Microsoft .Net Framework 4.5 and above • Wyse Device Agent version 14.0.0.
NOTE: • If the thin client is registered to Wyse Management Suite, all the local configurations deployed using the Wyse Easy Setup administrator shell are discarded. The remote configurations deployed using Wyse Management Suite are applied. • If the thin client is unregistered from Wyse Management Suite, the configurations deployed through Wyse Management Suite are discarded. The local configurations deployed using the Wyse Easy Setup administrator shell are applied.
13 Configuring Wyse Converter for PCs by using Wyse Management Suite You can install and configure the Wyse Converter for PCs software by using Wyse Management Suite.
Table 294. Registering device by using DHCP option tags Option Tag Description Name—WMS This tag points to the Wyse Management Suite server URL. For example, wmsserver.acme.com:443, where wmsserver.acme.com is fully qualified domain name of the server where Wyse Management Suite is installed. Data Type—String NOTE: Do not use https:// in the server URL, or the thin client will not register under Wyse Management Suite.
URL/Tag Record Type—SRV Description NOTE: MQTT is optional for the latest version of Wyse Management Suite. To register your devices in Wyse Management Suite public cloud, the device should point to the PNS (MQTT) servers in public cloud. For example, US1—us1-pns.wysemanagementsuite.com EU1—eu1-pns.wysemanagementsuite.com Record Name—_WMS_CAVALIDATION Record FQDN—_WMS_CAVALIDATION._tcp.
14 Teradici device management The Teradici device management section provides the information about managing and discovering the teradici divices. The teradici management console uses SDK’s to support management, configuration for tera devices. This is applicable only for Wyse Management Suite private cloud with pro license type. For more information on Teradici configuration policies, see Editing Teradici policy settings.
Discovery Method Low Security Manual discovery initiated by the Certificate not required MC Medium Security High Security Not applicable Not applicable Manual discovery from the client 1 Go to, https://. 2 Accept the certificate warning message. 3 Enter the administrator password (default password is Administrator) and login. 4 Go to, upload > certificate. Select the Cert.pemfile from the default path and click Upload. 5 Go to Configuration > Management.
10 Select PCoIP Endpoint as the Option class, and then click Add. 11 In the Option Type dialog, enter the name as EBM X.509 SHA-256 fingerprint, data type as String, code as 11, and the description as EBM X.509 SHA-256 fingerprint, and then click OK. 12 Expand the DHCP scope to which you want to apply the options. 13 Right-click the Scope Options, and then select Configure Options. 14 Click the Advanced tab, and then select the PCoIP Endpoint vendor class. 15 Select the 011 EBM X.
5 Browse the certificate, and the click View. 6 Copy the SHA-256 fingerprint. CIFS use case scenarios The following use cases are supported in Wyse Management Suite: • When you select Wyse Management Suite as Setup Type while installing Wyse Management Suite private cloud. – CIFS configuration page is displayed. This page is required as we need to configure the shared folder. NOTE: The Configure CIFS User Credentials option is disabled by default.
15 Wyse Device Agent The Wyse Device Agent (WDA) is a unified agent for all thin client management solutions. If you install WDA, you can manage thin clients using Wyse Management Suite. The following three types of customer security environments are supported by the Wyse Device Agent: • Highly secured environments—To mitigate the risk against rouge DHCP or DNS server for new device discovery, administrators must log in to each device individually and configure the Wyse Management Suite server URL.
16 Troubleshooting Wyse Management Suite Table 297. Troubleshooting Issue Workaround Email alert notifications are not working. Configure the SMTP server from the Wyse Management Suite server portal admin. Wake on LAN is not working. Enable the local or remote file repository. Unknown file type warning message is displayed when you double click the Wyse Management Suite launch icon. Check the security settings or UAC of the server. Ensure that all the Windows is updated with all the patches.
Issue Workaround When the agent registers with http, Wyse Management Suite sends the https URL and all the new agents switch to https. Agents 12.x does not have this behavior since the agent does not understand the switching login. No Supported sub Auth types error is displayed when you try to launch VNC session from Wyse Management Suite server after disabling the VNC User required password option. Launch the VNC with VNC User required password option.
Issue Workaround You cannot perform RAW imaging using RSP through Wyse Management Suite. To perform ThinLinux RAW imaging through Wyse Management Suite: 1 2 3 4 5 Create an FTP location. Copy the RAW image to the FTP location. Copy the RAW image file again from the Wyse Management Suite Repository. Create a Standard App policy with RAW image by providing the FTP location, user name, and password as install parameters. Schedule a policy job.
Issue Workaround Mongo, Maria and Tomcat services are stopped after restarting the Wyse Management Suite server. Windows defender service deletes the Wyse Management Suite related files. Check the defender service logs if any deleted files. Retrieve the deleted files. VC++ package takes 20 minutes to install. Ensure that the windows server is updated with the latest service packs and updates. Ensure that the Windows update is not in-progress while installing the Wyse Management Suite.
A Installing or upgrading Wyse Device Agent This section provides information about how to install or upgrade Wyse Device Agent on your thin clients, such as Windows Embedded Standard, Linux, and ThinLinux devices, by using Wyse Management Suite.
NOTE: • 3 • Click Yes. Different Wyse Device Agent packages are available for each variant of Windows Embedded Standard. A warning message is displayed when an older version of Wyse Device Agent or HAgent is installed on the device. 4 In the Group token field, enter a group token. This is an optional field. To skip this step, click Next. You can enter the group token details later in the Wyse Device Agent User Interface.
B Wyse Management Suite feature matrix The following table provides information about the features supported for each subscription type: Table 298.
Features Wyse Management Suite Standard Wyse Management Suite Pro-private cloud Wyse Management Suite Procloud edition Delegated administration Not supported Supported Supported Dynamic group creation and assignment based on device attributes Not supported Supported Supported Two-factor authentication Supported Supported Supported Active directory authentication for role based administration.
C Supported thin clients on Wyse management Suite Table 299. Supported thin clients Thin Clients Device Type Build number and Wyse Device Agent versions Linux Wyse 5010 thin client Wyse 7010 thin client 11.3.106 Wyse 5020 thin client Wyse Device Agent version 2.0.13-00.1 Platform Utility 1.0.4-0.1 Wyse 7020 thin client ThinLinux 1.0 Wyse 5020 thin client Wyse 5060 thin client 1.0.7 Wyse Device Agent version 2.4.3-00.01 Wyse 7020 thin client Wyse 3030 LT Wyse 3040 thin client 1.0.7.
Thin Clients Device Type Build number and Wyse Device Agent versions Wyse 5020 thin client 7091 Wyse Device Agent 14.4.0.135 Wyse 7020 thin client Windows 10 IoT Enterprise Wyse 7010 Extended thin client 896 Wyse Device Agent 14.4.0.135 Wyse 7040 thin client 7091 Wyse Device Agent 14.4.0.135 Latitude 3460 mobile thin client Latitude E7270 mobile thin client 7065 Wyse Device Agent 14.4.0.135 Wyse 5060 thin client 7091 Wyse Device Agent 14.4.0.
Thin Clients Device Type Build number and Wyse Device Agent versions Wyse 7010 thin client Wyse 3030 LT thin client Wyse 5060 thin client Wyse 3040 Thin Client Wyse 5070 thin client Firmware 8.6_185 Wyse 5070 Extended thin client Wyse 5470 thin client Wyse 5470 All-in-One thin client Teradici Wyse 5030 thin client, Wyse 7030 thin client Wyse 5050 thin client 222 Supported thin clients on Wyse management Suite Firmware 5.x (5.5.1, 5.4, 5.3) 6.x (6.0, 6.1.
D Wireless profiles password editor This Wireless profiles password editor is used to capture the wireless profiles and edit the passwords. The profiles are saved in an XML file. The same XML file can be used to configure the Wyse Management Suite through Cloud Client Manager. NOTE: .NET Framework 4.5 must be installed to run this tool on any Windows operating system or Windows Embedded operating system.
Figure 15. Wireless Profiles Password Editor 3 Click Browse and select the location to save the new XML profile. 4 Click the Export WIFI Profiles option. The current wireless profile is exported to the Profiles tab. The current wireless connection password is populated in the Password tab. 5 Edit the password and click the Change Password option. Changed password is encrypted and saved to the XML profile. 6 On the server side of Wyse Management Suite console, click App & Data tab.
E Create and configure DHCP option tags NOTE: For information on customer security environment, see Wyse Device Agent. To create a DHCP option tag, do the following: 1 Open the Server Manager. 2 Go to Tools, and click DHCP option. 3 Go to FQDN > IPv4 and right-click IPv4. Figure 16. DHCP 4 Click Set Predefined Options. The Predefined Options and Values window is displayed. 5 From the Option class drop-down list, select the DHCP Standard Option value.
Figure 17. Predefined Options and Values 6 Click Add. The Option Type window is displayed. Figure 18. Option Type The options must be either added to the server options of the DHCP server or scope options of the DHCP scope. Configuring the DHCP option tags • To create the 165 Wyse Management Suite server URL option tag, do the following: a Enter the following values, and click OK.
– Description—WMS_Server b Enter the following value, and then click OK. String—WMS FQDN For example, WMSServerName.YourDomain.Com:443 Figure 19. 165 Wyse Management Suite server URL option tag • To create the 166 MQTT server URL option tag, do the following: a Enter the following values, and click OK. – Name—MQTT – Data type—String – Code—166 – Description—MQTT Server b Enter the following value, and click OK. String—MQTT FQDN For example, WMSServerName.YourDomain.
Figure 20. 166 Wyse Management Suite server URL option tag • To create the 167 Wyse Management Suite CA Validation server URL option tag, do the following: a Enter the following values, and click OK. – Name—CA Validation – Data type—String – Code—167 – Description—CA Validation b Enter the following values, and click OK.
Figure 21. 167 Wyse Management Suite server URL option tag • To create the 199 Wyse Management Suite Group Token server URL option tag, do the following: a Enter the following values, and click OK. – Name—Group Token – Data type—String – Code—199 – Description—Group Token b Enter the following values, and click OK.
Figure 22.
F Create and configure DNS SRV records NOTE: For information on customer security environment, see Wyse Device Agent. To create a DNS SRV record, do the following: 1 Open the Server Manager. 2 Go to Tools, and click DNS option. 3 Go to DNS > DNS Server Host Name > Forward Lookup Zones > Domain > _tcp and right-click the _tcp option. Figure 23. DNS manager 4 Click Other New Records. The Resource Record Type window is displayed.
Figure 24. Resource Record Type a 232 To create Wyse Management Suite server record, enter the following details and click OK.
Figure 25. _WMS_MGMT service b To create MQTT server record, enter the following values, and then click ÓK.
Figure 26. _WMS_MQTT service 6 Go to DNS > DNS Server Host Name > Forward Lookup Zones > Domain and right-click the domain. 7 Click Other New Records.
Figure 27. Resource Record Type a To create Wyse Management Suite Group Token record, enter the following values, and click OK.
Figure 28. _WMS_GROUPTOKEN record name b 236 To create Wyse Management Suite CA validation record, enter the following values, and then click OK.
Figure 29.
G Steps to change the host name to IP address Steps to change the host name to IP address when host name resolution fails, to the following: 1 Open the DOS prompt in elevated Admin mode 2 Change the directory to C:\Program Files\DELL\WMS\MongoDB\bin. 3 Enter the command, mongo localhost -username stratus -p --authenticationDatabase admin Output—MongoDB shell version v3.4.10 4 Enter the password. Output— • 5 connecting to: mongodb://127.0.0.1:27017/localhost • MongoDB server version: 3.4.
