Dell XC6320 Web-Scale Hyperconverged Appliance Getting Started With Your System Scan to see how-to videos, documentation, and troubleshooting information.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2016 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
CAUTION: Restricted Access Location This system is intended for installation only in restricted access locations as defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions apply: • Access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken.
1 2 Push the latch release buttons on the midpoints of the end piece to open the rail latches (see Figure 1). Align the end pieces of the rails on the vertical rack flanges to seat the pegs in the bottom hole of the first U and the top hole of the second U. NOTE: The rails can be used in both square-hole and round-hole racks (see Figure 1). Figure 1. Pushing the Latch Release Buttons NOTE: To remove the rails, push the latch release button on the midpoints of the end piece and unseat each rail.
Figure 2. Installing the Chassis Stabilizer Shipping Brackets 7 8 Slide the system into the rack (see Figure 3). Tighten the thumbscrews to secure the ears of the system to the front of the rack flanges. Figure 3.
Connecting the Keyboard, Mouse, and Monitor (Optional) Figure 4. Optional—Connecting the Keyboard, Mouse and Monitor Connect the keyboard, mouse, and monitor (optional). The connectors on the back of your system have icons indicating which cable to plug into each connector. Ensure that you tighten the screws (if any) on the monitor’s cable connector. NOTE: The system supports only one USB port and a micro USB port. If you require more than one USB outlet at a time, use USB hub or an adapter cable.
Connecting the Power Cable(s) Figure 5. Connecting the Power cable Figure 6. Routing the cables Connect the system’s power cable(s) to the system and, if a monitor is used, connect the monitor’s power cable to the monitor. Plug the other end of the power cable(s) into a grounded electrical outlet or a separate power source such as an uninterrupted power supply (UPS) or a power distribution unit. NOTE: The system supports both AC and HVDC power inputs.
Turning on the System Figure 7. Pressing the Power Button in Front of the System Press the power button(s) either in front or back of the system. The power indicators glow in green color.
Installing Operating System To install an operating system for the first time, see the installation and configuration documentation for your operating system. Ensure that the operating system is installed before installing hardware or software not purchased with the system. For more information about the Dell XC6320 system, refer to the Dell XC6320 Owner’s Manual available at Dell.com/xcseriesmanuals. NOTE: For more information about supported operating systems, see Dell.com/ossupport.
Dell XC6320 Web 级超聚合设备 系统使用入门 扫描以查看教学视频、 文档和故障排除信息。
注、小心和警告 注:“注”表示可以帮助您更好地使用计算机的重要信息。 小心:“小心”表示如果不遵循说明,就有可能导致硬件损坏或数据丢失。 警告:“警告”表示可能导致财产损失、人身伤害或死亡的潜在危险。 版权所有 © 2016 Dell Inc. 保留所有权利。本产品受美国及国际版权法和知识产权法保护。Dell™ 和 Dell 徽标是 Dell Inc. 在美国和/或其他管辖区域的商标。此处提到的所有其他商标和名称可能是其各自所属公司的商标。 马来西亚印刷。 管制型号:B08S 2016 年 3 月 管制类型:B08S003 P/N G40F3 Rev.
小心:进出受限区域 本系统只能安装在进出受限区域中,此区域的限定出自 Cl.1.2.7.
1 2 推端件中间点位置处的闩锁释放按钮,以打开导轨闩锁(请参见图 1)。 在垂直机架凸缘上对齐导轨的各端件,将销钉安装在第一 U 的底部孔 和第二 U 的顶部孔中。 注:方形孔机架和圆形孔机架中均可使用导轨(参见图 1)。 图 1.
图 2. 安装机箱稳定装运支架 7 8 将系统滑入机架(请参见图 3)。 拧紧指旋螺钉,将系统耳状部分固定到机架凸缘的正面。 图 3.
连接键盘、鼠标和显示器(可选) 图 4.
连接电源电缆 图 5. 连接电源电缆 图 6.
开启系统 图 7.
安装操作系统 在首次安装操作系统时,参阅操作系统的安装和配置文档。确保首先安 装操作系统,然后安装未随该系统购买的硬件或软件。有关 Dell XC6320 系统的更多信息,参阅 Dell.com/xcseriesmanuals 上提供的 Dell XC6320 Owner’s Manual(Dell XC6320 用户手册)。 注:有关支持的操作系统的更多信息,参阅 Dell.
Dell XC6320 Web-Scale Hyperconverged Appliance Memulai Sistem Anda Pindai untuk melihat video panduan, dokumentasi, dan informasi pemecahan masalah.
Catatan, Perhatian, dan Peringatan CATATAN: CATATAN menunjukkan informasi penting yang akan membantu Anda untuk menggunakan komputer dengan lebih baik. PERHATIAN: PERHATIAN menunjukkan kemungkinan terjadinya kerusakan perangkat keras atau kehilangan data jika petunjuk tidak dipatuhi. PERINGATAN: PERINGATAN menunjukkan kemungkinan terjadinya kerusakan properti, cedera pribadi, atau kematian. Hak cipta © 2016 Dell Inc. Hak cipta dilindungi undang-undang.
PERHATIAN: Lokasi Akses Terbatas Sistem ini ditujukan hanya untuk pemasangan pada lokasi akses terbatas seperti yang dijelaskan dalam Kl. 1.2.7.3 dari IEC 60950-1: 2001 di mana kedua syarat berikut berlaku: • Akses hanya dapat dimiliki oleh seseorang yang bertanggung jawab terhadap atau oleh pengguna yang memiliki pengetahuan tentang alasan mengapa pembatasan berlaku pada lokasi dan tentang tindakan pencegahan yang harus dilakukan.
1 2 Tekan tombol pelepas selot pada bagian tengah ujung rel untuk membuka penguncian rel (lihat Gambar 1). Sejajarkan ujung rel pada pinggiran rak vertikal untuk menyelaraskan pasak di dalam lubang bawah pada U pertama dan lubang atas pada U kedua. CATATAN: Rel dapat digunakan baik untuk rak dengan lubang persegi maupun rak dengan lubang bulat (lihat Gambar 1). Gambar 1.
Gambar 2. Memasang Braket Penyeimbang Sasis 7 8 Dorong sistem ke dalam rak (lihat Gambar 3). Kencangkan sekrup baut untuk memasang telinga sistem pada bagian depan pinggiran rak. Gambar 3.
Menyambungkan Keyboard, Mouse, dan Monitor (Opsional) Gambar 4. Opsional—Menyambungkan Keyboard, Mouse, dan Monitor Sambungkan keyboard, mouse, dan monitor (opsional). Konektor pada sisi belakang sistem memiliki ikon yang menunjukkan kabel mana yang harus dipasang pada setiap konektornya. Pastikan bahwa Anda sudah mengencangkan sekrup (jika ada) dengan baik pada konektor kabel monitor. CATATAN: Sistem hanya mendukung satu port USB dan micro USB.
Menyambungkan Kabel Daya Gambar 5. Menyambungkan kabel Daya Gambar 6. Merutekan kabel Sambungkan kabel daya sistem ke sistem dan, jika Anda menggunakan monitor, sambungkan juga kabel daya monitor ke monitor. Sambungkan ujung kabel daya yang lain ke stopkontak yang diground atau ke sumber daya terpisah seperti UPS atau unit distribusi daya. CATATAN: Sistem mendukung input AC dan HVDC. Sistem Anda dapat mendukung dua unit suplai daya (PSU) hingga 1600 W (200−240 VAC tegangan input nominal).
Menyalakan Sistem Gambar 7. Menekan Tombol Daya di Sisi Depan Sistem Tekan tombol daya baik yang berada di sisi depan atau belakang sistem. Indikator daya akan menyala hijau.
Memasang Sistem Operasi Untuk memasang sistem operasi untuk pertama kalinya, lihat dokumentasi pemasangan dan konfigurasi untuk sistem operasi Anda. Pastikan bahwa sistem operasi telah terpasang sebelum memasang perangkat keras atau perangkat lunak yang tidak dibeli bersama sistem. Untuk informasi lebih lanjut mengenai sistem Dell XC6320, silakan lihat Panduan Pengguna Dell XC6320 yang tersedia di Dell.com/xcseriesmanuals.
Dell XC6320 ウェブスケール ハイパーコンバージド アプライアンス はじめに スキャンして、ハウツービデオ、マニュアル、および トラブルシューティングの情報を参照してください。
メモ、注意、警告 メモ:お使いのコンピュータをより良く使用するために役に立つ重要情報を示します。 注意:手順に従わない場合、ハードウェアの損傷やデータの損失が発生する可 能性があることを示します。 警告:物的損害、けが、または死亡の原因となる可能性があることを示しています。 著作権 © 2016 Dell Inc. 無断転載を禁じます。この製品は、米国ならびに国際的な著作権法および知的財産法によって保 護されています。Dell™ および Dell のロゴは米国および / またはその他管轄区域における Dell Inc. の商標です。本書で 使用されているその他すべての商標および名称は、各社の商標である場合があります。 Printed in Malaysia. 規制適合モデル:B08S 2016-03 規制適合タイプ:B08S003 P/N G40F3 Rev.
注意:立入制限区域 このシステムは、IEC 60950-1: 2001 の Cl.1.2.7.
1 末端部の中間点にあるラッチリリースボタンを押してレールラッチを開きます 2 レールのエンドピースを垂直ラックフランジに合わせ、ペグを 1 番目の U の (図 1 を参照)。 最下部の穴と 2 番目の U の最上部の穴に装着します。 メモ:レールは角型穴と丸型穴の両方のラックに使用できます(図 1 を参照)。 図 1.ラッチリリースボタンを押す メモ:レールを取り外すには、末端部の中間点にあるラッチリリースボタンを押して、 各レールを外します。 3 レールの末端をはめ込み、ラッチリリースボタンを離してラッチを所定の場 所にロックします。 4 背面の各垂直ラックフランジで、2 個のねじ込口金をレールのすぐ上にある 5 背面ラックフランジにシャーシスタビライザシッピングブラケット(オプシ ョン)を取り付けます。 6 ネジを取り付けて締めます。 2 つの角穴に差し込みます(図 2 を参照)。 メモ:ラックに取り付け済みのシステムを運搬するには、2 個のシャーシスタビライ ザ配送用ブラケット(オプション)が所定の位置にあることを確認してください。 34 | はじめに
図 2.シャーシスタビライザ配送用ブラケットの取り付け 7 8 システムをラックに挿入します(図 3 を参照)。 蝶ネジを締めて、システムの両側の耳をラックフランジの前面に固定します。 図 3.ラックへのシャーシの取り付け はじめに | 35
キーボード、マウスおよびモニタの接続(オプション) 図 4.オプション — キーボード、マウス、およびモニタの接続 キーボード、マウス、およびモニタ(オプション)を接続します。 システム背面のコネクタには、どのケーブルをどのコネクタに接続するかを示すアイ コンがあります。モニタのケーブルコネクタにネジがある場合は、必ずネジを締める ようにしてください。 メモ:このシステムは、USB ポートおよびマイクロ USB ポートをそれぞれ 1 個の みサポートします。2 つ以上の USB アウトレットが必要な場合は、USB ハブまた はアダプタケーブルを使用してください。 36 | はじめに
電源ケーブルの接続 図 5.電源ケーブルの接続 図 6.ケーブルの配線 システムの電源ケーブルをシステムに接続し、モニタを使用する場合はモニタの電源ケー ブルをモニタに接続します。電源ケーブルのもう一方の端をアースされたコンセントまた は無停電電源装置(UPS)や配電装置などの別の電源に接続します。 メモ:システムは AC および HVDC の両方の電源入力をサポートします。お使い のシステムは 1600 W の電源装置ユニット(PSU)を最大 2 台サポートします (200~240 VAC の公称入力電圧)。 はじめに | 37
システムへの電源投入 図 7.システム前面の電源ボタンを押す システムの前面または背面にある電源ボタンを押します。電源インジケータが緑色に点灯 します。 38 | はじめに
オペレーティングシステムのインストール オペレーティングシステムを初めてインストールする場合は、お使いのオペレー ティングシステムのインストールと設定に関するマニュアルを参照してくださ い。システムとは別途に購入したハードウェアやソフトウェアの取り付けとイン ストールは、オペレーティングシステムがインストール済みであることを確認し てから行ってください。Dell XC6320 システムの詳細については、 Dell.com/xcseriesmanuals で『Dell XC6320 Owner’s Manual』(Dell XC6320 オーナーズマニュアル)を参照してください。 メモ:対応オペレーティングシステムの詳細については、Dell.
Dell XC6320 웹-스케일 하이퍼 컨버지드 어플라이언스 시스템 시작하기 비디오, 설명서 및 문제 해결 정보 사용법을 보려면 스캔하십시오.
주, 주의 및 경고 주: 주는 컴퓨터의 활용도를 높이는 데 도움이 되는 중요한 정보입니다. 주의: 주의는 지침을 따르지 않을 경우 하드웨어의 손상이나 데이터의 유실을 유발할 수 있는 위험이 있음을 알려줍니다. 경고: 경고는 재산 피해, 부상 또는 사망이 발생될 수 있는 위험 상황을 나타냅니다. Copyright © 2016 Dell Inc. 저작권 본사 소유. 이 제품은 미국 및 국제 저작권 지적 재산 법에 의해 보호됩니다. Dell™ 및 Dell 로고는 미국 및/또는 기타 관할지역에서 사용되는 Dell Inc.의 상표입니다. 이 문서에 언급된 기타 모든 표시 및 이름은 각 회사의 상표일 수 있습니다. 말레이시아에서 인쇄. 규정 모델: B08S 2016-03 규정 유형: B08S003 P/N G40F3 Rev.
주의: 제한 접근 지역 본 시스템은 다음 두 조건이 적용되는 IEC 60950-1: 2001의 Cl. 1.2.7.3에서 정의된 제한 접근 지역에서만 설치할 수 있습니다. • 해당 지역에 적용되는 제한 사유 및 취해야 할 모든 예방 조치에 관해 지도를 받은 서비스 기술자 또는 사용자만 액세스할 수 있습니다. • 접근은 공구, 자물쇠 및 키 또는 다른 보안 수단을 사용하여 이루어지며, 지역 담당 책임자에 의해 제어됩니다. 설치 및 구성 경고: 다음 절차를 수행하기 전에 시스템과 함께 제공된 안전 지침을 검토하여 따르십시오. 도구 없이 레일 솔루션 설치 경고: 시스템을 들어야 하는 경우에는 다른 사람에게 도움을 요청합니다. 부상당할 우려가 있으므로 시스템을 혼자 들지 마십시오. 경고: 시스템이 랙에 고정되어 있지 않거나 레일에 장착되어 있지 않습니다. 부상이나 시스템의 손상을 방지하려면, 설치하거나 분리할 때 시스템을 충분히 지지해야 합니다.
1 2 끝 부분의 중심점에 있는 래치 분리 단추를 눌러 레일 래치를 엽니다.(그림 1 참조) 레일의 끝 부분을 수직 랙 플랜지에 맞추어 첫 번째 U의 아래쪽 구멍 및 두 번째 U의 위쪽 구멍에 페그를 장착합니다. 주: 레일은 네모 구멍과 원형 구멍 랙에 모두 사용될 수 있습니다 (그림 1 참조) 그림 1. 래치 분리 단추 누르기 주: 레일을 분리하려면 끝 부분의 중심점에 있는 래치 분리 단추를 눌러 각 레일을 빼냅니다. 3 4 5 6 레일 끝을 걸고 래치 분리 단추를 놓아 래치를 제자리에 잠급니다. 후면에 있는 각 수직 랙 플랜지에서 두 개의 나사 베이스를 레일의 바로 위에 있는 두 개의 네모 구멍에 넣습니다.(그림 2 참조) 후면 랙 플랜지의 섀시 고정 장치 운송 브래킷(선택사양)을 설치합니다. 나사를 끼워 조입니다. 주: 랙에 이미 설치되어 있는 시스템을 옮기려면 2개의 섀시 고정 장치 운송 브래킷(선택 사양)이 제자리에 있는지 확인합니다.
그림 2. 섀시 고정 장치 운송 브래킷 설치 7 8 시스템을 랙에 밀어 넣습니다.(그림 3 참조) 나비 나사를 조여 시스템 모서리를 랙 플랜지 전면에 고정합니다. 그림 3.
키보드, 마우스 및 모니터 연결(선택사양) 그림 4. 선택사양 - 키보드, 마우스 및 모니터 연결 키보드, 마우스 및 모니터를 연결합니다(선택사양). 시스템 후면에 있는 커넥터에는 각 커넥터에 연결될 케이블이 표시된 아이콘이 있습니다. 나사(있는 경우)를 모니터의 케이블 커넥터에 고정합니다. 주: 시스템은 하나의 USB 포트와 하나의 마이크로 USB 포트만 지원합니다. 한 번에 하나 이상의 USB 포트가 필요한 경우, USB 허브 또는 어댑터 케이블을 사용하십시오.
전원 케이블 연결 그림 5. 전원 케이블 연결 그림 6. 케이블 경로 설정 시스템의 전원 케이블을 시스템에 연결하고, 모니터를 사용하는 경우 모니터의 전원 케이블을 모니터에 연결합니다. 전원 케이블의 반대쪽 끝을 접지된 전원 콘센트나, UPS(무정전 전원 공급 장치) 또는 PDU(배전 장치)와 같은 별도의 전원에 연결합니다. 주: 시스템은 AC와 HVDC 전원 입력 장치를 모두 지원합니다. 시스템은 두 개의 1600 W 전원 공급 장치(PSU)를 지원합니다. (200−240 VAC 정격 입력 전압).
시스템 켜기 그림 7. 시스템 전면에서 전원 단추 누르기 시스템 전면 또는 후면에서 전원 단추를 누릅니다. 전원 표시등은 초록색으로 빛납니다.
운영 체제 설치 운영 체제를 처음으로 설치할 경우 해당 운영 체제의 설치 및 구성 설명서를 참조하십시오. 시스템과 함께 구입하지 않은 하드웨어 또는 소프트웨어를 설치할 시 운영 체제가 설치되어 있는지 확인합니다. Dell XC6320 시스템에 관한 자세한 정보는 Dell.com/xcseriesmanuals에서 Dell XC6320 소유자 매뉴얼을 참조합니다. 주: 지원되는 운영 체제에 대한 자세한 정보는 Dell.com/ossupport를 참조합니다.