Manual de servicio de Dell™ XPS™ L702X Modelo normativo: serie P09E Tipo normativo: P09E002
Notas, precauciones y avisos NOTA: una NOTA indica información importante que le ayuda a conseguir un mejor rendimiento de su equipo. PRECAUCIÓN: un mensaje de PRECAUCIÓN indica la posibilidad de daños en el hardware o la pérdida de datos si no se siguen las instrucciones. AVISO: un mensaje de AVISO indica el riesgo de daños materiales, lesiones o incluso la muerte. ____________________ La información contenida en este documento puede modificarse sin aviso previo. © 2010 Dell Inc.
Contenido 1 Antes de comenzar . . . . . . . . . . . . . . . . . . Herramientas recomendadas Apagado del equipo . . . . . . . . . . . . . . . 9 . . . . . . . . . . . . . . . . . . . . 9 Antes de trabajar en el interior de su equipo . 2 3 4 5 Batería . 9 . . . . . 10 . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Extracción de la batería . . . . . . . . . . . . . . . . . 13 Colocación de la batería . . . . . . . . . . . . . . . . 14 Cubierta del módulo . . . . . . . . . . . .
6 7 8 9 Unidad(es) de disco duro . . . . . . . . . . . Extracción de la unidad de disco duro . . . . . . . . . 27 Colocación de la unidad de disco duro . . . . . . . . . 30 Unidad óptica . . . . . . . . . . . . . . . . . . . . . 33 Extracción de la unidad óptica . . . . . . . . . . . . . 33 Colocación de la unidad óptica . . . . . . . . . . . . . 34 Ensamblaje del reposamanos . . . . . . . . 35 Extracción del ensamblaje del reposamanos . . . . . .
11 Batería de tipo botón . . . . . . . . . . . . . . . . 49 Extracción de la batería de celda del espesor de una moneda . . . . . . . . . . . . . . . . . 49 Colocación de la batería de tipo botón . . . . . . . . . 50 . . . . . . . . . . . . . . . . . . . . . . . . . . 51 12 Pantalla Ensamblaje de la pantalla . . . . . . . . . . . . . . . . 51 Extracción del ensamblaje de la pantalla . . . . . 51 Colocación del ensamblaje de la pantalla . . . . . 55 . . . . . . . . . . . . . . . . . . .
13 Placa IR . . . . . . . . . . . . . . . . . . . . . . . . . Extracción de la placa IR . . . . . . . . . . . . . . . . 69 Colocación de la placa IR . . . . . . . . . . . . . . . . 70 14 Módulo de la cámara . . . . . . . . . . . . . . . 73 Extracción del módulo de la cámara . . . . . . . . . . 73 Colocación del módulo de la cámara . . . . . . . . . . 76 15 Cubierta superior . . . . . . . . . . . . . . . . . . 79 Extracción de la cubierta superior . . . . . . . . . . .
18 Ventilador 93 . . . . . . . . . . . . . . . . . . . . . . . . Extracción del ventilador Colocación del ventilador . 19 Disipador de calor . 93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 . . . . . . . . . . . . . . . . . 97 Extracción del disipador de calor . . . . . . . . . . . . 97 Colocación del disipador de calor . . . . . . . . . . . 99 20 Módulo del procesador . . . . . . . . . . . . . Extracción del módulo del procesador 101 . . . . . . . . .
23 Placa USB . . . . . . . . . . . . . . . . . . . . . . . Extracción de la placa USB . . . . . . . . . . . . . . Colocación de la placa USB . 24 Placa base . 115 . . . . . . . . . . . . . 117 . . . . . . . . . . . . . . . . . . . . . . 119 Extracción de la placa base . . . . . . . . . . . . . . 119 Colocación de la placa base. . . . . . . . . . . . . . 122 Introducción de la etiqueta de servicio en el BIOS 25 Altavoces . Colocación del altavoz . 123 125 . . . . . . . . . . . . .
Antes de comenzar En este manual se describen los procedimientos para retirar e instalar los componentes del equipo. A menos que se señale lo contrario, cada procedimiento asume que existen las siguientes condiciones: • Ha realizado los pasos descritos en "Apagado del equipo" en la página 9 y en "Antes de trabajar en el interior de su equipo" en la página 10. • Ha leído la información sobre seguridad que venía con su equipo.
Antes de trabajar en el interior de su equipo Aplique las siguientes pautas de seguridad para proteger el equipo contra posibles daños y para garantizar su propia seguridad personal. AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance.
5 Desconecte su ordenador y todos los dispositivos conectados de las tomas de alimentación eléctrica. 6 Desconecte todos los dispositivos conectados al equipo. PRECAUCIÓN: Para evitar daños en la placa base, extraiga la batería principal (ver "Extracción de la batería" en la página 13) antes de manipular el interior de su equipo. 7 Extraiga la batería (consulte el apartado "Extracción de la batería" en la página 13).
Antes de comenzar
Batería AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
2 1 1 Batería 2 Pasador de liberación de la batería Colocación de la batería PRECAUCIÓN: Para evitar daños en el equipo, utilice únicamente la batería diseñada específicamente para este ordenador Dell. 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Alinee las pestañas de la batería con las ranuras del compartimento y presione la batería hasta que encaje.
Cubierta del módulo AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
4 3 2 1 1 Cubierta de la base 2 Lengüetas 3 Cubierta de módulo 4 Tornillo de sujeción Colocación de la cubierta del módulo 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Alinee las lengüetas de la cubierta del módulo de memoria con las marcas de la cubierta de la base y encaje el módulo en su sitio. 3 Apriete el tornillo cautivo que fija la cubierta del módulo a la cubierta de la base.
Módulos de memoria AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
4 Abra cuidadosamente con la punta de los dedos los ganchos de fijación situados en cada extremo del conector del módulo de memoria hasta que salga el módulo de memoria. 1 3 2 1 Conector del módulo de memoria 3 Módulo de memoria 2 Ganchos de fijación (2) 5 Extraiga el módulo de memoria de su conector. Colocación de los módulos de memoria 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9.
Conector del módulo de memoria Número de módulos de memoria 1 DIMM A DIMM B X X 2 X X 4 DIMM D X X 3 DIMM C X X X X X X X X X X X X 2 Alinee la muesca del módulo de memoria con la lengüeta del conector del módulo de memoria. 3 Deslice el módulo de memoria para introducirlo firmemente en el conector del módulo de memoria formando un ángulo de 45 grados y presiónelo hasta que encaje en su sitio. Si no oye un chasquido, extraiga el módulo de memoria y vuelva a instalarlo.
NOTA: Si el módulo de memoria no se ha instalado correctamente, es posible que el equipo no se inicie. 3 2 1 1 Lengüeta 2 3 Conector del módulo de memoria Muesca 4 Vuelva a colocar la cubierta del módulo (ver "Colocación de la cubierta del módulo" en la página 16). 5 Coloque de nuevo la batería (consulte la "Colocación de la batería" en la página 14). 6 Conecte el adaptador de CA al equipo y a una toma de alimentación eléctrica.
Minitarjetas inalámbricas AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
3 Retire la cubierta del módulo (ver "Extracción de la cubierta del módulo" en la página 15). 4 Retire la unidad óptica (consulte "Extracción de la unidad óptica" en la página 33). 5 Extraiga el ensamblaje del reposamanos (ver "Extracción del ensamblaje del reposamanos" en la página 35). 6 Saque el teclado (consulte el apartado "Extracción del teclado" en la página 41). 7 Desconecte los cables de antena de las minitarjetas. 8 Retire el tornillo que fija la minitarjeta a la placa base.
9 Extraiga la(s) minitarjeta(s) del conector de la placa base. PRECAUCIÓN: Mientras la minitarjeta no esté instalada en el equipo, guárdela en un embalaje con protección antiestática. Para obtener más información, consulte el apartado "Protección contra descargas electrostáticas" que se encuentra en la información de seguridad que se envió con el equipo. Colocación de las minitarjetas 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Desembale la minitarjeta nueva.
PRECAUCIÓN: Para evitar dañar la minitarjeta, no coloque nunca cables debajo de la tarjeta. 3 Introduzca el conector de la minitarjeta con un ángulo de 45 grados en el conector de la placa base. 4 Presione el otro extremo de la minitarjeta para introducirlo en la ranura de la placa base y vuelva a colocar los tornillos que fijan la minitarjeta a la placa base. 5 Conecte los cables de antena adecuados en la minitarjeta que está instalando.
PRECAUCIÓN: Antes de encender el equipo, vuelva a colocar todos los tornillos y asegúrese de que no queda ninguno perdido dentro. Si no lo hace, el equipo podría estropearse. 11 Instale los controladores y las utilidades para el equipo, según sea necesario. NOTA: Si está instalando una tarjeta de comunicaciones que no sea de Dell, tendrá que instalar las utilidades y controladores adecuados.
Minitarjetas inalámbricas
Unidad(es) de disco duro AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. AVISO: Si extrae la unidad de disco duro del equipo cuando la unidad está caliente, no toque la carcasa metálica de dicha unidad.
3 Retire la cubierta del módulo (ver "Extracción de la cubierta del módulo" en la página 15). 4 Retire la unidad de disco duro 1 y la unidad de disco duro 2 de la base del equipo: • Quite los cuatro tornillos que fijan el ensamblaje de la unidad de disco duro a la base del ordenador. • Usando la lengüeta de tiro, deslice el ensamblaje de la unidad de disco duro para desconectarlo del conector de la placa base. • Levante el ensamblaje de la unidad de disco duro para sacarlo de la base del equipo.
Unidad de disco duro 2 3 2 1 1 Lengüeta de tiro 3 Tornillos (4) 2 Ensamblaje de la unidad de disco duro 5 Extraiga los cuatro tornillos que fijan el soporte de la unidad de disco duro a éste. 6 Levante el soporte de la unidad de disco duro para sacarlo de ésta.
3 2 1 1 Unidad de disco duro 3 Tornillos (4) 2 Soporte para la unidad de disco duro Colocación de la unidad de disco duro 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Saque la nueva unidad de disco duro de su embalaje. Conserve el embalaje original para almacenar o transportar la unidad de disco duro. 3 Coloque el soporte para unidad de disco duro en la unidad de disco duro. 4 Vuelva a colocar los cuatro tornillos que fijan el soporte para disco duro a éste.
• Vuelva a colocar los cuatro tornillos que fijan el ensamblaje de la unidad de disco duro a la base del equipo. 6 Vuelva a colocar la cubierta del módulo (ver "Colocación de la cubierta del módulo" en la página 16). 7 Coloque de nuevo la batería (consulte la "Colocación de la batería" en la página 14). PRECAUCIÓN: Antes de encender el equipo, vuelva a colocar todos los tornillos y asegúrese de que no queda ninguno perdido dentro. Si no lo hace, el equipo podría estropearse.
Unidad(es) de disco duro
Unidad óptica AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
1 3 2 1 Tornillo 3 Cubierta de la base 2 Unidad óptica Colocación de la unidad óptica 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Deslice la unidad óptica hasta que esté completamente asentada en el compartimiento. 3 Vuelva a colocar los tornillos que sujetan la unidad óptica a la cubierta de la base. 4 Vuelva a colocar la cubierta del módulo (ver "Colocación de la cubierta del módulo" en la página 16).
Ensamblaje del reposamanos AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
6 Déle la vuelta al equipo y abra la pantalla el máximo posible. 7 Con la punta del dedo, empuje la lengüeta para liberar el ensamblaje del reposamanos de la cubierta superior.
1 3 2 1 Ensamblaje del reposamanos 3 Lengüeta 2 Cubierta superior PRECAUCIÓN: Separe con cuidado el ensamblaje del reposamanos de la cubierta superior para evitar que se dañe. 8 Utilizando la punta de los dedos, saque suavemente el reposamanos de la cubierta superior. 9 Sin tirar fuerte del ensamblaje del reposamanos, dele la vuelta y colóquelo sobre la cubierta superior.
3 1 4 2 1 Conector del cable de control 2 Conector del cable de la superficie táctil 3 Cubierta superior 4 Ensamblaje del reposamanos Colocación del ensamblaje del reposamanos 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Inserte el cable de la superficie táctil en el conector de la placa base y ejerza presión sobre el pestillo del conector para fijar el cable.
7 Vuelva a colocar la unidad óptica (consulte "Colocación de la unidad óptica" en la página 34). 8 Vuelva a colocar la cubierta del módulo (ver "Colocación de la cubierta del módulo" en la página 16). 9 Coloque de nuevo la batería (consulte la "Colocación de la batería" en la página 14). PRECAUCIÓN: Antes de encender el equipo, vuelva a colocar todos los tornillos y asegúrese de que no queda ninguno perdido dentro. Si no lo hace, el equipo podría estropearse.
Ensamblaje del reposamanos
Teclado AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
PRECAUCIÓN: Extreme la precaución cuando extraiga y manipule el teclado. De lo contrario, se podría rayar el panel de la pantalla. 1 2 3 1 Teclado 3 Cubierta superior 2 Lengüetas (6) 7 Dele la vuelta al teclado y colóquelo sobre la cubierta superior. 8 Levante el pestillo del conector y tire de la lengüeta de extracción para desconectar el cable de retroiluminación del teclado del conector de la placa base.
4 3 1 2 1 Cubierta superior 2 Teclado 3 Conector del cable de retroiluminación del teclado 4 Conector del cable del teclado 10 Levante el teclado de la cubierta superior. Colocación del teclado 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Inserte el cable del teclado en el conector de la placa base y ejerza presión sobre el pestillo del conector para fijar el cable.
5 Vuelva a colocar el ensamblaje del reposamanos (ver "Colocación del ensamblaje del reposamanos" en la página 38). 6 Vuelva a colocar la unidad óptica (consulte "Colocación de la unidad óptica" en la página 34). 7 Vuelva a colocar la cubierta del módulo (ver "Colocación de la cubierta del módulo" en la página 16). 8 Coloque de nuevo la batería (consulte la "Colocación de la batería" en la página 14).
Panel del botón de encendido AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
1 2 3 4 1 Tornillos (2) 2 Ensamblaje del reposamanos 3 Panel del botón de encendido 4 Conector del cable del panel del botón de alimentación Colocación del panel del botón de encendido 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Utilice el indicador de alineación para colocar el panel del botón de encendido en el ensamblaje del reposamanos. 3 Vuelva a colocar los dos tornillos que sujetan el panel al ensamblaje del reposamanos.
8 Coloque de nuevo la batería (consulte la "Colocación de la batería" en la página 14). PRECAUCIÓN: Antes de encender el equipo, vuelva a colocar todos los tornillos y asegúrese de que no queda ninguno perdido dentro. Si no lo hace, el equipo podría estropearse.
Panel del botón de encendido
Batería de tipo botón AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
1 2 1 Batería de tipo botón 2 Punta trazadora de plástico Colocación de la batería de tipo botón 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Introduzca la batería de tipo botón en el zócalo de la batería de la placa base con el lado positivo hacia arriba. 3 Vuelva a colocar el ensamblaje del reposamanos (ver "Colocación del ensamblaje del reposamanos" en la página 38). 4 Vuelva a colocar la unidad óptica (consulte "Colocación de la unidad óptica" en la página 34).
Pantalla AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
5 Retire la unidad óptica (consulte "Extracción de la unidad óptica" en la página 33). 6 Extraiga el ensamblaje del reposamanos (ver "Extracción del ensamblaje del reposamanos" en la página 35). 7 Saque el teclado (consulte el apartado "Extracción del teclado" en la página 41). 8 Desconecte los cables de antena de las minitarjetas (consulte el apartado "Extracción de minitarjetas" en la página 21). PRECAUCIÓN: Tenga mucho cuidado al abrir la pantalla para evitar que el ensamblaje sufra daños.
11 Tire de la lengüeta para desconectar el cable de la pantalla táctil del conector de la placa base. 12 Afloje el tornillo que sujeta el cable de toma a tierra de la pantalla a la cubierta superior. 13 Tire de la lengüeta para desconectar el cable de la pantalla del conector de la placa base. 14 Recuerde la disposición del cable de la pantalla y retírelo de las guías de colocación.
5 4 1 2 3 1 Tornillo de sujeción 2 Cable de toma a tierra 3 Cable de la pantalla 4 Conector del cable de la pantalla táctil 5 Cables de antena (2) 15 Quite los cuatro tornillos que fijan el ensamblaje de la pantalla a la base del equipo.
16 Levante el ensamblaje de la pantalla de la base del equipo. Colocación del ensamblaje de la pantalla 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Ponga el ensamblaje de la pantalla en su posición y vuelva a colocar los cuatro tornillos que fijan dicho ensamblaje a la cubierta superior. 3 Pase el cable de la pantalla por las guías de colocación. 4 Conecte el cable de la pantalla al conector de la placa base.
Bisel de la pantalla Extracción del bisel de la pantalla PRECAUCIÓN: El bisel de la pantalla es extremadamente frágil. Tenga cuidado cuando lo retire para evitar dañarlo. 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Extraiga el ensamblaje de la pantalla (ver "Extracción del ensamblaje de la pantalla" en la página 51). 3 Presione hacia fuera el embellecedor de la pantalla para liberarlo de las pestañas que lo sujetan a la cubierta posterior.
Colocación del bisel de la pantalla 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Alinee el embellecedor de la pantalla por encima de la cubierta posterior de la misma y ajústelo en su sitio con cuidado. 3 Vuelva a colocar el ensamblaje de la pantalla (consulte "Colocación del ensamblaje de la pantalla" en la página 55). PRECAUCIÓN: Antes de encender el equipo, vuelva a colocar todos los tornillos y asegúrese de que no queda ninguno perdido dentro.
1 2 3 1 Placa de la pantalla táctil 3 Panel de la pantalla b 58 2 Cable de la placa de la pantalla táctil Quite los ocho tornillos que fijan el panel de la panalla a la cubierta posterior de la pantalla.
1 2 3 1 Tornillos (8) 3 Panel de la pantalla 2 Bisagras (2) NOTA: La placa IR es opcional y puede no estar presente en su equipo. 6 Si es necesario, extraiga la tarjeta IR: a Tire de la lengüeta para desconectar el cable de la placa IR del conector de ésta.
1 2 3 1 Panel de la pantalla 2 Tornillos (6) 3 Cable de la placa IR 4 Placa IR b 4 Quite los seis tornillos que fijan el panel de la panalla a la cubierta posterior de la pantalla. 7 Observe la colocación de los cables de antena y extráigalos de la guía de colocación de la bisagra derecha de la pantalla. 8 Observe la colocación del cable de la pantalla y extráigalo de la guía de colocación de la bisagra izquierda de la pantalla.
Colocación del panel de la pantalla 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Coloque el panel de la pantalla sobre la cubierta posterior de la pantalla. 3 Coloque el cable de la pantalla a través de la guía de colocación de la bisagra izquierda de la pantalla. 4 Pase los cables de antena por la guía de colocación de la bisagra derecha de la pantalla.
3 Extraiga el bisel de la pantalla (ver "Extracción del bisel de la pantalla" en la página 56). 4 Retire el módulo de la cámara ("Extracción del módulo de la cámara" en la página 73). 5 Extraiga el panel de la pantalla (ver "Extracción del panel de la pantalla" en la página 57). 6 Dé la vuelta al panel de la pantalla y colóquelo en una superficie limpia. 7 Retire suavemente la cinta del panel de la pantalla.
9 Retire suavemente el cable de la pantalla de la parte posterior del panel de ésta. Colocación del cable de la pantalla 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Adhiera el cable de la pantalla por el borde del panel. 3 Conecte el cable de la pantalla al conector del panel de la pantalla. 4 Vuelva a colocar el panel de la pantalla (ver "Colocación del panel de la pantalla" en la página 61).
1 2 1 Soportes del panel de la pantalla (2) 2 Tornillos (8) Colocación de los soportes del panel de la pantalla 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Coloque los soportes del panel de la pantalla en su sitio. 3 Vuelva a colocar los ocho tornillos (cuatro en cada lado) que fijan los soportes del panel de la pantalla a este último. 4 Vuelva a colocar el panel de la pantalla (ver "Colocación del panel de la pantalla" en la página 61).
PRECAUCIÓN: Antes de encender el equipo, vuelva a colocar todos los tornillos y asegúrese de que no queda ninguno perdido dentro. Si no lo hace, el equipo podría estropearse. Bisagras de la pantalla Extracción de las bisagras de la pantalla 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Extraiga el ensamblaje de la pantalla (ver "Extracción del ensamblaje de la pantalla" en la página 51).
1 2 1 Cubierta posterior de la pantalla 2 Tornillos (4) Colocación de las bisagras de la pantalla 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Coloque las bisagras de la pantalla en su sitio. 3 Vuelva a colocar los cuatro tornillos (dos de cada lado) que fijan las bisagras de la pantalla a la cubierta posterior. 4 Vuelva a colocar el panel de la pantalla (ver "Colocación del panel de la pantalla" en la página 61).
PRECAUCIÓN: Antes de encender el equipo, vuelva a colocar todos los tornillos y asegúrese de que no queda ninguno perdido dentro. Si no lo hace, el equipo podría estropearse.
Pantalla
Placa IR AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el ordenador. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
9 Tire de la lengüeta para desconectar el cable de la placa IR del conector de ésta. 10 Levante la placa IR de la cubierta posterior de la pantalla. 2 1 1 Cable de la placa IR 2 Placa IR Colocación de la placa IR 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Conecte el cable de la placa IR al conector de la misma. 3 Utilice las marcas de alineación para colocar la placa IR en la cubierta posterior de la pantalla.
7 Vuelva a colocar el ensamblaje del reposamanos (ver "Colocación del ensamblaje del reposamanos" en la página 38). 8 Vuelva a colocar la unidad óptica (consulte "Colocación de la unidad óptica" en la página 34). 9 Vuelva a colocar la cubierta del módulo (ver "Colocación de la cubierta del módulo" en la página 16). 10 Coloque de nuevo la batería (consulte la "Colocación de la batería" en la página 14).
Placa IR
Módulo de la cámara AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
9 Levante con cuidado el módulo de la cámara de la cubierta posterior de la pantalla. 1 1 Módulo de la cámara 10 Quite con cuidado la cinta que fija el cable de la cámara al módulo de la misma.
1 2 1 Cinta 2 Módulo de la cámara 11 Tire de la lengüeta de tiro para desconectar el cable de la cámara del conector del módulo de la cámara. 12 Levante el módulo de la cámara de la cubierta posterior de la pantalla.
1 2 1 Conector del cable de la cámara 2 Módulo de la cámara Colocación del módulo de la cámara 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Conecte el cable de la cámara al conector del módulo de la cámara. 3 Pegue la cinta que fija el cable de la cámara al módulo de la misma. 4 Utilice las marcas de alineación para colocar el módulo de la cámara en la cubierta posterior de la pantalla.
7 Vuelva a colocar el teclado (ver "Colocación del teclado" en la página 43). 8 Vuelva a colocar el ensamblaje del reposamanos (ver "Colocación del ensamblaje del reposamanos" en la página 38). 9 Vuelva a colocar la unidad óptica (consulte "Colocación de la unidad óptica" en la página 34). 10 Vuelva a colocar la cubierta del módulo (ver "Colocación de la cubierta del módulo" en la página 16). 11 Coloque de nuevo la batería (consulte la "Colocación de la batería" en la página 14).
Módulo de la cámara
Cubierta superior AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
9 Extraiga los diez tornillos que fijan el ensamblaje de la cubierta superior a la cubierta de la base. 10 Dele la vuelta al equipo. 11 Extraiga los diez tornillos que fijan el ensamblaje de la cubierta superior a la cubierta de la base. 12 Desconecte el cable del subwoofer del conector de la placa base.
1 1 Cable del subwoofer 13 Con la punta de los dedos, libere un poco el ensamblaje de la cubierta superior de la cubierta de la base. 14 Levante el ensamblaje de la cubierta.
1 1 Ensamblaje de la cubierta superior 15 Extraiga el conector del adaptador de CA (consulte "Extracción del conector del adaptador de CA" en la página 89). 16 Extraiga la placa USB (consulte "Extracción de la placa USB" en la página 115). 17 Extraiga el ventilador (consulte el apartado "Extracción del ventilador" en la página 93). 18 Extraiga el disipador de calor (consulte "Extracción del disipador de calor" en la página 97).
21 Extraiga el conector de la antena de TV (consulte "Extracción del conector de la antena de TV" en la página 111). 22 Extraiga la placa base (ver "Extracción de la placa base" en la página 119). 23 Extraiga los altavoces (consulte "Extracción de los altavoces" en la página 125). Colocación de la cubierta superior 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Vuelva a colocar los altavoces (consulte "Colocación del altavoz" en la página 127).
15 Dele la vuelta al equipo y vuelva a colocar los diez tornillos que fijan el ensamblaje de la cubierta superior a la cubierta de la base. 16 Vuelva a colocar el ensamblaje de la pantalla (consulte "Colocación del ensamblaje de la pantalla" en la página 55). 17 Vuelva a colocar el teclado (ver "Colocación del teclado" en la página 43). 18 Vuelva a colocar el ensamblaje del reposamanos (ver "Colocación del ensamblaje del reposamanos" en la página 38).
Subwoofer AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
9 Extraiga el ensamblaje de la pantalla (ver "Extracción del ensamblaje de la pantalla" en la página 51). 10 Extraiga las minitarjetas (ver "Extracción de minitarjetas" en la página 21). 11 Siga las instrucciones del paso 9 al paso 14 de "Extracción de la cubierta superior" en la página 79. 12 Quite los cuatro tornillos que fijan el subwoofer a la cubierta de la base. 13 Levante el subwoofer junto con el cable de la cubierta de la base.
3 Vuelva a colocar los cuatro tornillos que fijan el subwoofer a la cubierta de la base. 4 Siga las instrucciones del paso 11 al paso 15 de "Colocación de la cubierta superior" en la página 83. 5 Vuelva a colocar las minitarjetas (ver "Colocación de las minitarjetas" en la página 23). 6 Vuelva a colocar el ensamblaje de la pantalla (consulte "Colocación del ensamblaje de la pantalla" en la página 55). 7 Vuelva a colocar el teclado (ver "Colocación del teclado" en la página 43).
Subwoofer
Conector del adaptador de CA AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
9 Extraiga el ensamblaje de la pantalla (ver "Extracción del ensamblaje de la pantalla" en la página 51). 10 Extraiga las minitarjetas (ver "Extracción de minitarjetas" en la página 21). 11 Siga las instrucciones del paso 9 al paso 14 de "Extracción de la cubierta superior" en la página 79. 12 Dele la vuelta al ensamblaje de la cubierta superior. 13 Tome nota de la colocación del cable del conector del adaptador de CA y extraiga el cable de las guías de colocación.
Colocación del conector del adaptador de CA 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Alinee el agujero del tornillo del conector del adaptador de CA con el agujero del tornillo de la cubierta superior. 3 Vuelva a colocar el tornillo que fija el conector del adaptador de CA a la cubierta superior. 4 Pase el cable del conector del adaptador de CA por las guías de colocación. 5 Conecte el conector del adaptador de CA al conector de la placa base.
Conector del adaptador de CA
Ventilador AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. AVISO: Si saca el disipador de calor del procesador del equipo mientras está aún caliente, no toque la carcasa de metal del disipador de calor.
8 Saque el teclado (consulte el apartado "Extracción del teclado" en la página 41). 9 Extraiga el ensamblaje de la pantalla (ver "Extracción del ensamblaje de la pantalla" en la página 51). 10 Extraiga las minitarjetas (ver "Extracción de minitarjetas" en la página 21). 11 Siga las instrucciones del paso 9 al paso 14 de "Extracción de la cubierta superior" en la página 79. 12 Dele la vuelta al ensamblaje de la cubierta superior. 13 Desconecte el cable del ventilador del conector de la placa base.
1 2 4 3 1 Tornillos (2) 2 Ventilador 3 Cubierta superior 4 Cable del ventilador Colocación del ventilador 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Alinee los orificios para tornillos del ventilador con los orificios para tornillos de la cubierta superior. 3 Vuelva a colocar los dos tornillos que fijan el ventilador a la cubierta superior. 4 Conecte el cable del ventilador al conector de la placa base.
7 Vuelva a colocar las minitarjetas (ver "Colocación de las minitarjetas" en la página 23). 8 Vuelva a colocar el ensamblaje de la pantalla (consulte "Colocación del ensamblaje de la pantalla" en la página 55). 9 Vuelva a colocar el teclado (ver "Colocación del teclado" en la página 43). 10 Vuelva a colocar el ensamblaje del reposamanos (ver "Colocación del ensamblaje del reposamanos" en la página 38). 11 Vuelva a colocar la unidad óptica (consulte "Colocación de la unidad óptica" en la página 34).
Disipador de calor AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. AVISO: Si saca el disipador de calor del ordenador mientras está aún caliente, no toque la carcasa de metal del disipador de calor.
8 Saque el teclado (consulte el apartado "Extracción del teclado" en la página 41). 9 Extraiga el ensamblaje de la pantalla (ver "Extracción del ensamblaje de la pantalla" en la página 51). 10 Extraiga las minitarjetas (ver "Extracción de minitarjetas" en la página 21). 11 Siga las instrucciones del paso 9 al paso 14 de "Extracción de la cubierta superior" en la página 79. 12 Dele la vuelta al ensamblaje de la cubierta superior.
Colocación del disipador de calor NOTA: La grasa térmica original puede reutilizarse si el procesador original y el disipador de calor se vuelven a instalar al mismo tiempo. Si sustituye el procesador o el disipador de calor, utilice la almohadilla térmica incluida en el kit para garantizar la conductividad térmica. 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Elimine el lubricante térmico de la parte inferior del disipador de calor y vuelva a aplicarlo.
Disipador de calor
Módulo del procesador AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
9 Extraiga el ensamblaje de la pantalla (ver "Extracción del ensamblaje de la pantalla" en la página 51). 10 Extraiga las minitarjetas (ver "Extracción de minitarjetas" en la página 21). 11 Siga las instrucciones del paso 9 al paso 14 de "Extracción de la cubierta superior" en la página 79. 12 Dele la vuelta al ensamblaje de la cubierta superior. 13 Extraiga el disipador de calor (consulte "Extracción del disipador de calor" en la página 97).
4 3 1 2 1 Zócalo ZIF 2 Módulo del procesador 3 Esquina de la patilla 1 4 Tornillo de leva del zócalo ZIF PRECAUCIÓN: Para garantizar la máxima refrigeración del módulo del procesador, no toque las zonas de transferencia del calor del ensamblaje de refrigeración del procesador. La grasa de su piel puede reducir la capacidad de transferencia de calor de las almohadillas térmicas. PRECAUCIÓN: Cuando extraiga el módulo del procesador, tire de él hacia arriba.
Colocación del módulo del procesador NOTA: Si va a instalar un nuevo módulo del procesador, recibirá un nuevo ensamblaje de refrigeración con una almohadilla térmica adherida, o bien recibirá una nueva almohadilla térmica junto con documentación en la que se muestra cómo se debe instalar correctamente. 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Alinee la esquina de la pata 1 del procesador con la esquina de la pata 1 del zócalo ZIF.
13 Vuelva a colocar los módulos de memoria (consulte "Colocación de los módulos de memoria" en la página 18). 14 Vuelva a colocar la cubierta del módulo (ver "Colocación de la cubierta del módulo" en la página 16). 15 Coloque de nuevo la batería (consulte la "Colocación de la batería" en la página 14). PRECAUCIÓN: Antes de encender el equipo, vuelva a colocar todos los tornillos y asegúrese de que no queda ninguno perdido dentro. Si no lo hace, el equipo podría estropearse.
Módulo del procesador
Placa de E/S AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: sólo un técnico certificado debe realizar reparaciones en el ordenador. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
9 Extraiga el ensamblaje de la pantalla (ver "Extracción del ensamblaje de la pantalla" en la página 51). 10 Extraiga las minitarjetas (ver "Extracción de minitarjetas" en la página 21). 11 Siga las instrucciones del paso 9 al paso 14 de "Extracción de la cubierta superior" en la página 79. 12 Desconecte el cable del altavoz del conector de la placa de E/S. 1 1 Conector del cable del altavoz 13 Dele la vuelta al ensamblaje de la cubierta superior.
15 Extraiga con cuidado los conectores de la placa de E/S de las ranuras de la cubierta superior y levante la placa base para sacarla de la cubierta superior. 1 3 2 1 Tornillos (3) 3 Cubierta superior 2 Placa de E/S Colocación de la placa de E/S 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Alinee los conectores de la placa de E/S con las ranuras de la cubierta superior y coloque la placa sobre ella.
7 Vuelva a colocar las minitarjetas (ver "Colocación de las minitarjetas" en la página 23). 8 Vuelva a colocar el ensamblaje de la pantalla (consulte "Colocación del ensamblaje de la pantalla" en la página 55). 9 Vuelva a colocar el teclado (ver "Colocación del teclado" en la página 43). 10 Vuelva a colocar el ensamblaje del reposamanos (ver "Colocación del ensamblaje del reposamanos" en la página 38). 11 Vuelva a colocar la unidad óptica (consulte "Colocación de la unidad óptica" en la página 34).
Conector de la antena de TV AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
9 Extraiga el ensamblaje de la pantalla (ver "Extracción del ensamblaje de la pantalla" en la página 51). 10 Extraiga las minitarjetas (ver "Extracción de minitarjetas" en la página 21). 11 Siga las instrucciones del paso 9 al paso 14 de "Extracción de la cubierta superior" en la página 79. 12 Extraiga la placa de E/S (ver "Extracción de la placa de E/S" en la página 107). 13 Tome nota de la colocación del cable del conector de la antena de TV y extraiga el cable de las guías de colocación.
Colocación del conector de la antena de TV 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Alinee el conector de la antena de TV con la ranura situada en la cubierta superior y colóquelo en ésta. 3 Vuelva a colocar los dos tornillos que fijan el conector de la antena de TV a la cubierta superior. 4 Pase el cable del conector del adaptador de CA por la guía de colocación. 5 Vuelva a colocar la placa de E/S (ver "Colocación de la placa de E/S" en la página 109).
Conector de la antena de TV
Placa USB AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
9 Extraiga el ensamblaje de la pantalla (ver "Extracción del ensamblaje de la pantalla" en la página 51). 10 Extraiga las minitarjetas (ver "Extracción de minitarjetas" en la página 21). 11 Siga las instrucciones del paso 9 al paso 14 de "Extracción de la cubierta superior" en la página 79. 12 Dele la vuelta al ensamblaje de la cubierta superior. 13 Levante el pestillo del conector y desconecte el cable de la placa USB dependiente del conector de la placa USB.
Colocación de la placa USB 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Alinee los conectores de la placa USB con las ranuras de la cubierta superior y coloque la placa sobre ella. 3 Vuelva a colocar el tornillo que fija la placa USB a la cubierta superior. 4 Deslice el cable de la placa USB en el conector de la placa base y presione el pestillo hacia abajo para fijar el cable.
Placa USB
Placa base AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
8 Extraiga el ensamblaje del reposamanos (ver "Extracción del ensamblaje del reposamanos" en la página 35). 9 Saque el teclado (consulte el apartado "Extracción del teclado" en la página 41). 10 Extraiga el ensamblaje de la pantalla (ver "Extracción del ensamblaje de la pantalla" en la página 51). 11 Extraiga las minitarjetas (ver "Extracción de minitarjetas" en la página 21). 12 Extraiga la batería de tipo botón (ver "Extracción de la batería de celda del espesor de una moneda" en la página 49).
15 Extraiga el disipador de calor (consulte "Extracción del disipador de calor" en la página 97). 16 Saque el módulo del procesador (consulte "Extracción del módulo del procesador" en la página 101). 17 Extraiga la placa de E/S (ver "Extracción de la placa de E/S" en la página 107). 18 Desconecte el cable del ventilador y el cable del adaptador de CA de los conectores de la placa base. 19 Levante la placa base de la cubierta superior.
Colocación de la placa base 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Levante la placa base de la cubierta superior. 3 Conecte el cable del ventilador y el cable del adaptador de CA a los conectores de la placa base. 4 Vuelva a colocar la placa de E/S (ver "Colocación de la placa de E/S" en la página 109). 5 Vuelva a colocar el módulo del procesador (consulte "Colocación del módulo del procesador" en la página 104).
18 Coloque de nuevo la batería (consulte la "Colocación de la batería" en la página 14). 19 Vuelva a colocar toda tarjeta o panel protector que quitó de la ranura del lector de tarjetas multimedia. PRECAUCIÓN: Antes de encender el equipo, vuelva a colocar todos los tornillos y asegúrese de que no queda ninguno perdido dentro. Si no lo hace, el equipo podría estropearse. 20 Encienda el equipo.
Placa base
Altavoces AVISO: Antes trabajar en el interior del equipo, siga las instrucciones de seguridad que se entregan con el equipo. Para obtener información adicional sobre prácticas recomendadas de seguridad, visite la página de inicio sobre el cumplimiento de normativas en www.dell.com/regulatory_compliance. PRECAUCIÓN: Sólo un técnico certificado debe realizar reparaciones en el equipo. La garantía no cubre los daños por reparaciones no autorizadas por Dell™.
1 1 Cable del altavoz 4 Extraiga la placa base (ver "Extracción de la placa base" en la página 119). 5 Observe la colocación de los cables de los altavoces y extraiga el cable de las guías. 6 Extraiga los cuatro tornillos (dos en cada altavoz) que fijan los altavoces a la cubierta superior. 7 Levante los altavoces junto con el cable de la cubierta superior.
1 2 1 Altavoces (2) 3 Cable del altavoz 3 2 Tornillos (4) Colocación del altavoz 1 Siga las instrucciones del apartado "Antes de comenzar" en la página 9. 2 Coloque el cable del altavoz siguiendo las guías. 3 Alinee los orificios para tornillos de los altavoces con los orificios para tornillos de la cubierta superior. 4 Vuelva a colocar los cuatro tornillos (dos en cada altavoz) que fijan los altavoces a la base del equipo.
6 Conecte el cable del altavoz al conector de la placa base. 7 Coloque de nuevo la batería (consulte la "Colocación de la batería" en la página 14). PRECAUCIÓN: Antes de encender el equipo, vuelva a colocar todos los tornillos y asegúrese de que no queda ninguno perdido dentro. Si no lo hace, el equipo podría estropearse.
Actualización del BIOS Puede que se tenga que actualizar el BIOS cuando haya una actualización disponible o cuando se sustituya la placa base. Para actualizar el BIOS: 1 Encienda el equipo. 2 Vaya a support.dell.com/support/downloads. 3 Busque el archivo de actualización del BIOS de su equipo: NOTA: La etiqueta de servicio del equipo se encuentra en una etiqueta en la parte inferior del equipo.
6 Haga clic en Save (Guardar) para guardar el archivo en su escritorio. El archivo se descargará en el escritorio. 7 Haga clic en Close (Cerrar) si aparece la ventana Download Complete (Descarga finalizada). El icono del archivo aparece en el escritorio con el mismo título que el archivo de actualización del BIOS descargado. 8 Haga doble clic en el icono del archivo en el escritorio y siga las instrucciones que se muestran en pantalla.