Dell XPS M2010 Service Manual Dell™ XPS™ M2010 Service Manual Before You Begin Memory Module Mini Card Coin-Cell Battery Subwoofer Internal Card With Bluetooth Wireless Technology Keyboard Cosmetic Covers Top Cover Display Camera Optical Drive Wireless USB Board Hard Drive(s) System Fans Video Card/Thermal-Cooling Assembly Processor Thermal-Cooling Assembly Processor Module Frame Modem System Board Assembly Computer Base Flashing the BIOS Pin Assignments for I/O Connectors Notes, Notices, and Cautions NOT
Before You Begin: Dell XPS M2010 Service Manual Back to Contents Page Before You Begin Dell™ XPS™ M2010 Service Manual Recommended Tools Turning Off Your Computer Before Working Inside Your Computer Replacing the System Battery This section provides procedures for removing and installing the components in your computer.
Before You Begin: Dell XPS M2010 Service Manual CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins. NOTICE: Only a certified service technician should perform repairs on your computer.
Before You Begin: Dell XPS M2010 Service Manual b. Using your thumbs, slide the battery in the direction of the #2 arrow by inserting one thumb into the recess next to the battery access door and the other thumb into the indention surrounding the #2 arrow. c. Lift the battery straight up and out of the computer. Replacing the System Battery 1. Press the release latch on the battery to open the access door. 2. Insert the battery straight down into the battery bay. file:///C|/Users/santhosh_v.
Before You Begin: Dell XPS M2010 Service Manual 3. Slide the battery in the direction of the #1 arrow until it snaps into place. 4. Close the access door, next to the #1 arrow, on the battery. Back to Contents Page file:///C|/Users/santhosh_v.ASIA-PACIFIC/Desktop/Hawke/New%20folder/begin.
Before You Begin: Dell XPS M2010 Service Manual file:///C|/Users/santhosh_v.ASIA-PACIFIC/Desktop/Hawke/New%20folder/begin.
Memory Module: Dell XPS M2010 Service Manual Back to Contents Page Memory Module Dell™ XPS™ M2010 Service Manual Removing the Memory Module Cover Removing the Memory Module Replacing the Memory Module CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components.
Memory Module: Dell XPS M2010 Service Manual Removing the Memory Module NOTICE: To prevent damage to the memory module connector, do not use tools to spread the memory-module securing clips. 1. Use your fingertips to carefully spread apart the securing clips on each end of the memory module connector until the module pops up. 2. Remove the module from the connector on the system board.
Memory Module: Dell XPS M2010 Service Manual To confirm the amount of memory installed in the computer, click the Start button, click Help and Support, and then click Computer Information. Back to Contents Page file:///C|/Users/santhosh_v.ASIA-PACIFIC/Desktop/Hawke/New%20folder/memory.
Mini Card: Dell XPS M2010 Service Manual Back to Contents Page Mini Card Dell™ XPS™ M2010 Service Manual Removing a Mini Card Replacing a Mini Card CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. CAUTION: Only products approved for use in your portable computer may be installed.
Mini Card: Dell XPS M2010 Service Manual 1 mini card 2 metal securing tabs (2) 5. Lift the card out of its connector. Replacing a Mini Card NOTICE: To avoid damaging the card, ensure that the antenna cable is not under the card when you click the card into place. NOTICE: The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors and realign the card. 1.
Mini Card: Dell XPS M2010 Service Manual 1 white arrow 4 mini card 2 black arrow 3 antenna cables 3. Replace the memory module cover (see Replacing the Memory Module). 4. Replace the system battery (see Replacing the System Battery). Back to Contents Page file:///C|/Users/santhosh_v.ASIA-PACIFIC/Desktop/Hawke/New%20folder/cards.
Coin-Cell Battery: Dell XPS M2010 Service Manual Back to Contents Page Coin-Cell Battery Dell™ XPS™ M2010 Service Manual Removing the Coin-Cell Battery Replacing the Coin-Cell Battery CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components.
Coin-Cell Battery: Dell XPS M2010 Service Manual 2. Carefully press the coin-cell battery into the compartment, being careful not to break the plastic. 3. Replace the memory module cover (see Removing the Memory Module Cover). 4. Replace the system battery (see Replacing the System Battery). Back to Contents Page file:///C|/Users/santhosh_v.ASIA-PACIFIC/Desktop/Hawke/New%20folder/coinbatt.
Subwoofer: Dell XPS M2010 Service Manual Back to Contents Page Subwoofer Dell™ XPS™ M2010 Service Manual Removing the Subwoofer Replacing the Subwoofer CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface.
Subwoofer: Dell XPS M2010 Service Manual 9. Disconnect the cable for the internal card with Bluetooth® wireless technology from the connector on the system board (JBT). 1 subwoofer cable and system board connector 2 cable for the card with Bluetooth technology and system board connector 10. To easily access the bottom of the computer, lean the display backwards and lay it on a flat surface so that the base is facing you. 1 computer base 2 subwoofer 3 display 11.
Subwoofer: Dell XPS M2010 Service Manual 1. Adhere the card with Bluetooth wireless technology (with cable attached) to the new subwoofer. 2. Insert the new subwoofer into the computer base, pushing it firmly into place. Ensure that the subwoofer cable reaches through to the system board. 3. Slide the subwoofer cover into place, and attach the subwoofer cover to the battery bay using two M2 x 4-mm screws. 4. Lift the display and place the computer base flat on the work surface. 5.
Internal Card With Bluetooth Wireless Technology: Dell XPS M2010 Service Manual Back to Contents Page Internal Card With Bluetooth Wireless Technology Dell™ XPS™ M2010 Service Manual Removing the Internal Card with Bluetooth Wireless Technology Replacing the Internal Card with Bluetooth Wireless Technology CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide.
Internal Card With Bluetooth Wireless Technology: Dell XPS M2010 Service Manual 2. Adhere the new internal card with Bluetooth wireless technology to the subwoofer. 3. Replace the subwoofer cover (see Replacing the Subwoofer). 4. Replace the system battery (see Replacing the System Battery). Back to Contents Page file:///C|/Users/santhosh_v.ASIA-PACIFIC/Desktop/Hawke/New%20folder/blue.
Keyboard: Dell XPS M2010 Service Manual Back to Contents Page Keyboard Dell™ XPS™ M2010 Service Manual Removing the Keyboard Battery Replacing the Keyboard Battery CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components.
Keyboard: Dell XPS M2010 Service Manual 1 keyboard 2 captive screw 3 keyboard battery Replacing the Keyboard Battery 1. Insert the new keyboard battery into the battery compartment and snap it into place. 2. Tighten the captive screw. Back to Contents Page file:///C|/Users/santhosh_v.ASIA-PACIFIC/Desktop/Hawke/New%20folder/keyboard.
Cosmetic Covers: Dell XPS M2010 Service Manual Back to Contents Page Cosmetic Covers Dell™ XPS™ M2010 Service Manual Removing the Cosmetic Covers Replacing the Cosmetic Covers CAUTION: Before performing the following procedures, follow the safety instructions in your Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components.
Cosmetic Covers: Dell XPS M2010 Service Manual 1. Insert a small, flat-blade screwdriver into the slot on the back right corner of the computer, and press the screwdriver in firmly all the way. 2. While holding the screwdriver in, align the tabs on the bottom of the cosmetic cover with the notches in the top cover. 3. Gently push the cosmetic cover down and release the screwdriver. 4. Repeat step 1 through step 3 to replace the left cosmetic cover.
Top Cover: Dell XPS M2010 Service Manual Back to Contents Page Top Cover Dell™ XPS™ M2010 Service Manual Removing the Top Cover Replacing the Top Cover CAUTION: Before performing the following procedures, follow the safety instructions in your Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface.
Top Cover: Dell XPS M2010 Service Manual 1 top cover 2 optical drive cable 3 media cable Replacing the Top Cover 1. While holding the top cover in one hand, connect the optical drive cable to its connector on the system board (JOD) and the media cable to its connector on the system board (JMEDIA). 2. Set the top cover in place and attach it to the computer with six M2.5 x 5-mm screws on the left side and seven M2.5 x 5-mm screws on the right side of the top cover at the embossed arrows. 3.
Display: Dell XPS M2010 Service Manual Back to Contents Page Display Dell™ XPS™ M2010 Service Manual Opening the Display Closing the Display Adjusting the Display Panel Removing the LCD Panel Replacing the LCD Panel CAUTION: Before performing the following procedures, follow the safety instructions in your Product Information Guide.
Display: Dell XPS M2010 Service Manual NOTE: If the system battery is drained and there is no power source, the latches will not automatically emerge, but you can manually activate them by sliding the display latch release buttons forward. 3. Firmly close the lid so all four latches are engaged. NOTICE: Ensure that all four latches are engaged securely before picking up the computer to move it or the keyboard could fall and be damaged.
Display: Dell XPS M2010 Service Manual 1 speaker cable 2 infrared sensor cable 3 suspend and solenoid function cable 4 mini card antenna cables 5 routing hooks for the antenna cables 6 routing hook 5. Turn the computer over and open the display (see Opening the Display). 6. Detach the keyboard by grasping the sides of the keyboard and pulling it straight out from the computer base. Set the keyboard aside. 7. Remove the cosmetic covers (see Removing the Cosmetic Covers). 8.
Display: Dell XPS M2010 Service Manual 1 system board 2 solenoid cable 3 solenoid card 13. Remove the six M2.5 x 8-mm screws that attach the left and right hinge arms to the computer base. 1 system board 2 M2.5 x 8-mm screws (6) 3 hinge arms 14. Tilt the display forward slightly so the display does not tip over backwards when you remove the computer base. 15. Lift the computer base and carefully thread the solenoid and video cables through the opening in the bottom of the computer base.
Display: Dell XPS M2010 Service Manual 1 video cable 2 solenoid cable 3 opening in computer base 16. Lay the display on its back on a flat clean surface. NOTICE: When working on the display, be careful not to touch the camera. The glass on the camera is fragile. 17. Starting at the top of the panel, remove the black display bezel from around the LCD panel by carefully prying it loose. 1 black display bezel 2 camera 3 LCD panel 18. On the silver display inlay, remove four M2.
Display: Dell XPS M2010 Service Manual 1 M2.5 x 5-mm screws (4) 2 M2.5-mm shoulder screws (12) 3 silver display inlay 19. Starting at the top of the panel, remove the silver inlay from around the LCD panel by carefully prying it loose. 20. On the rails that hold the LCD panel to the display, remove four M2 x 3-mm screws from the left rail, four M2 x 3-mm screws from the right rail, and two M2 x 3-mm screws from the bottom rail. NOTE: Do not remove the screws that hold the display latches in place.
Display: Dell XPS M2010 Service Manual 1 LCD panel 2 LCD cable 3 pull tab 22. To remove the rails from the LCD panel, remove two M2 x 3-mm screws from the top rail, four M2 x 3- mm screws from the right rail (marked "R"), and four M2 x 3-mm screws from the left rail (marked "L"). The bottom rail is adhered to the LCD panel. Reserve the other three rails to attach to the new LCD panel. 1 M2 x 3-mm screws (10) 2 left rail 4 top rail 5 right rail 3 LCD panel Replacing the LCD Panel 1.
Display: Dell XPS M2010 Service Manual 4. Snap the silver display inlay back into place around the panel. 5. Attach the silver display inlay to the display using four M2.5 x 5-mm screws in the holes labeled "A" and twelve M2.5mm shoulder screws in the remaining holes. NOTE: When replacing the silver display inlay, ensure that the display latches fit through the correct holes. 6. Snap the black display bezel into place. 7.
Display: Dell XPS M2010 Service Manual 19. Connect the antenna cables from the mini card. 20. Connect the speaker cable to the connector on the system board (JSPK). 21. Connect the suspend and solenoid function cable to the connector on the system board (JHING). 22. Connect the infrared sensor cable to the connector on the system board (JCIR). 23. Replace the memory module cover (see Replacing the Memory Module). 24. Replace the system battery (see Replacing the System Battery).
Camera: Dell XPS M2010 Service Manual Back to Contents Page Camera Dell™ XPS™ M2010 Service Manual Removing the Camera Replacing the Camera CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface.
Camera: Dell XPS M2010 Service Manual Replacing the Camera 1. Attach the new camera and cable to the top of the display with five M2 x 3-mm screws. 2. Connect the camera cable to the connector on the display. 3. Follow the instructions for replacing the silver display inlay and the black display bezel (see Replacing the LCD Panel). NOTICE: To avoid damage to the keyboard, ensure that you attach the keyboard securely before moving the computer. 4.
Optical Drive: Dell XPS M2010 Service Manual Back to Contents Page Optical Drive Dell™ XPS™ M2010 Service Manual Removing the Optical Drive Assembly Replacing the Optical Drive Assembly CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components.
Optical Drive: Dell XPS M2010 Service Manual 4 end caps 7. While holding the optical drive assembly and the top cover together, turn the top cover over. 8. Disconnect and untape the disk sensor cable from the top cover. 9. Rotate the swing arm on the top cover toward the optical drive assembly to put the optical drive in the "Open" position. 1 top cover (underside) 2 optical drive assembly 3 disk sensor cable 10.
Optical Drive: Dell XPS M2010 Service Manual 1 notch in swing arm (2) 2 tab on optical drive assembly (2) 3 optical drive cable Removing Media from the Optical Drive If media becomes stuck in the optical drive, you can retrieve the media by opening the drive. 1. Remove the optical drive assembly (see Removing the Optical Drive Assembly.) 2. Remove the optical drive from the optical drive assembly by removing the four M2.0-mm shoulder screws that hold the optical drive to the assembly. 1 M2.
Optical Drive: Dell XPS M2010 Service Manual 1 optical drive rails (2) 2 optical drive 3 M2 x 3-mm screws on rails (4) 5. Remove the optical drive cable from the optical drive by removing the two M2 x 3-mm screws. 6. Remove the four M2.0-mm shoulder screws on the optical drive cover. 7. Slide the top cover away from the front bezel to disengage the tabs, and lift the drive cover off the drive. 8. Remove the media from the drive. 1 M2.
Optical Drive: Dell XPS M2010 Service Manual 1 notch in swing arm (2) 2 tab on optical drive assembly (2) 3 optical drive cable 4. Rotate the swing arm away from the optical assembly to bring the optical drive to the "Closed" position. 5. Attach the disk sensor cable and tape it to the underside of the top cover. 6. Holding the optical drive assembly in place, turn the top cover over. 7. Attach the optical drive assembly to the top cover with two M2.5 x 5-mm screws and end caps. 8.
Wireless USB Board: Dell XPS M2010 Service Manual Back to Contents Page Wireless USB Board Dell™ XPS™ M2010 Service Manual Removing the Wireless USB Board Replacing the Wireless USB Board CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. CAUTION: Only products approved for use in your portable computer may be installed.
Wireless USB Board: Dell XPS M2010 Service Manual Replacing the Wireless USB Board 1. Attach the new wireless USB board with the M2 x 3-mm screw. 2. Connect the wireless USB cable to the system board. 3. Replace the top cover (see Replacing the Top Cover). 4. Replace the cosmetic covers (see Replacing the Cosmetic Covers). NOTICE: To avoid damage to the keyboard, ensure that you attach the keyboard securely before moving the computer. 5.
Hard Drive(s): Dell XPS M2010 Service Manual Back to Contents Page Hard Drive(s) Dell™ XPS™ M2010 Service Manual Removing a Hard Drive Replacing a Hard Drive Returning a Hard Drive to Dell CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive. CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide.
Hard Drive(s): Dell XPS M2010 Service Manual 1. Follow the instructions in Before Working Inside Your Computer, including removing the system battery. 2. Turn the computer over and open the display (see Opening the Display). 3. Detach the keyboard by grasping the sides of the keyboard and pulling it straight out from the computer base. Set the keyboard aside. 4. Remove the cosmetic covers (see Removing the Cosmetic Covers). 5. Remove the top cover (see Removing the Top Cover). 6.
Hard Drive(s): Dell XPS M2010 Service Manual 1 hard drive 4 hard drive cable connector 2 M3 x 3-mm screws (4) 3 hard drive brackets (2) Replacing a Hard Drive 1. Attach the new hard drive to the brackets using four M3 x 3-mm screws. 2. Connect the data cable to the new hard drive. 3. Connect the hard drive cable to the appropriate connector on the system board (JHDD1 for primary; JHDD2 for secondary). 4.
Hard Drive(s): Dell XPS M2010 Service Manual Returning a Hard Drive to Dell Return your old hard drive to Dell in its original or comparable foam packaging. Otherwise, the hard drive may be damaged in transit. 1 hard drive 2 foam packaging Back to Contents Page file:///C|/Users/santhosh_v.ASIA-PACIFIC/Desktop/Hawke/New%20folder/hdd.
System Fans: Dell XPS M2010 Service Manual Back to Contents Page System Fans Dell™ XPS™ M2010 Service Manual Removing a System Fan Replacing a System Fan CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface.
System Fans: Dell XPS M2010 Service Manual 7. Remove the fan from the frame by removing the three M2.5 x 5-mm screws. 8. Lift the fan out of the computer. Replacing a System Fan NOTE: If the system board was replaced, be sure to reattach the microphone cable under the left fan before replacing the fan. 1 microphone cable 2 microphone cable connector 3 system board connector 1. Attach the left fan to the computer frame using three M2.5 x 5-mm screws. 2.
System Fans: Dell XPS M2010 Service Manual 1 M2.5 x 5-mm screws (3) 2 fan cable 4 system board connector (JFAN1) 5 left system fan 3 notch in frame 4. Attach the right fan to the computer frame using three M2.5 x 5-mm screws. 5. Route the right fan cable under the notch on the frame. 6. Connect the right fan cable to the system board connector (JFAN2). 7. Replace the top cover (see Replacing the Top Cover). 8. Replace the cosmetic covers (see Replacing the Cosmetic Covers).
Video Card/Thermal-Cooling Assembly: Dell XPS M2010 Service Manual Back to Contents Page Video Card/Thermal-Cooling Assembly Dell™ XPS™ M2010 Service Manual Removing the Video Card/Thermal-Cooling Assembly Replacing the Video Card/Thermal-Cooling Assembly CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide.
Video Card/Thermal-Cooling Assembly: Dell XPS M2010 Service Manual 1 video card/thermal-cooling assembly 2 captive screws (4) 3 system board connector (JVGA) NOTE: The video card is integrated with its thermal assembly. Do not remove the heatsink from the video card. 9. Pull the video card/thermal-cooling assembly straight up to disconnect the card from the system board. Replacing the Video Card/Thermal-Cooling Assembly 1.
Video Card/Thermal-Cooling Assembly: Dell XPS M2010 Service Manual Back to Contents Page file:///C|/Users/santhosh_v.ASIA-PACIFIC/Desktop/Hawke/New%20folder/video.
Processor Thermal-Cooling Assembly: Dell XPS M2010 Service Manual Back to Contents Page Processor Thermal-Cooling Assembly Dell™ XPS™ M2010 Service Manual Removing the Processor Thermal-Cooling Assembly Replacing the Processor Thermal-Cooling Assembly CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide.
Processor Thermal-Cooling Assembly: Dell XPS M2010 Service Manual 1 processor thermal-cooling assembly 2 captive screws (5) Replacing the Processor Thermal-Cooling Assembly NOTE: If you are replacing the thermal-cooling assembly without removing and replacing a new processor, you can place the new thermal pad directly on any existing thermal pad already installed on the thermal-cooling assembly. It is not necessary to remove an existing pad or to clean the surface. 1.
Processor Module: Dell XPS M2010 Service Manual Back to Contents Page Processor Module Dell™ XPS™ M2010 Service Manual Removing the Processor Module Replacing the Processor Module CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components.
Processor Module: Dell XPS M2010 Service Manual 1 ZIF-socket cam screw 4 processor module 2 pin-1 corner of microprocessor 3 ZIF-socket NOTICE: When removing the processor module, pull the module straight up. Be careful not to bend the pins on the processor module. 9. Lift the processor module from the ZIF socket. Replacing the Processor Module NOTICE: Ensure that the cam lock is in the fully open position before seating the processor module.
Processor Module: Dell XPS M2010 Service Manual 3. Replace the processor thermal-cooling assembly (see Replacing the Processor Thermal-Cooling Assembly). 4. Replace the left hard drive (see Replacing a Hard Drive). 5. Replace the top cover (see Replacing the Top Cover). 6. Replace the cosmetic covers (see Replacing the Cosmetic Covers). NOTICE: To avoid damage to the keyboard, ensure that you attach the keyboard securely before moving the computer. 7.
Frame: Dell XPS M2010 Service Manual Back to Contents Page Frame Dell™ XPS™ M2010 Service Manual Removing the Frame Replacing the Frame CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface.
Frame: Dell XPS M2010 Service Manual 1 frame 2 M2.5 x 8-mm screws (14) Replacing the Frame 1. Attach the frame to the computer base with fourteen M2.5 x 8-mm screws. 2. Replace the processor thermal-cooling assembly (see Replacing the Processor Thermal-Cooling Assembly). 3. Replace the video card/thermal-cooling assembly (see Replacing the Video Card/Thermal-Cooling Assembly). 4. Replace the system fans (see Replacing a System Fan). 5. Replace the hard drive(s) (see Replacing a Hard Drive). 6.
Modem: Dell XPS M2010 Service Manual Back to Contents Page Modem Dell™ XPS™ M2010 Service Manual Removing the Modem Replacing the Modem CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface.
Modem: Dell XPS M2010 Service Manual 1 system board connector 2 M2 x 3-mm screws (2) 4 modem 5 modem cable 3 pull-tab Replacing the Modem 1. Connect the modem cable to the modem. NOTICE: Ensure that the modem cable is routed correctly when you replace the modem. 2. Align the connector on the bottom of the modem with the modem connector on the system board, and press down on the "PRESS HERE" label on the modem to connect it to the system board. 3.
Modem: Dell XPS M2010 Service Manual file:///C|/Users/santhosh_v.ASIA-PACIFIC/Desktop/Hawke/New%20folder/modem.
System Board Assembly: Dell XPS M2010 Service Manual Back to Contents Page System Board Assembly Dell™ XPS™ M2010 Service Manual Removing the System Board Assembly Replacing the System Board Assembly CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components.
System Board Assembly: Dell XPS M2010 Service Manual 1 speaker cable 2 infrared cable 3 suspend and solenoid function cable 4 memory modules 5 coin-cell battery 6 mini card 7 mini card antenna cables 8 routing hooks for mini card antenna cables 9 routing hook 7. Turn the computer over and open the display (see Opening the Display). 8. Detach the keyboard by grasping the sides of the keyboard and pulling it straight out from the computer base. Set the keyboard aside. 9.
System Board Assembly: Dell XPS M2010 Service Manual 1 system board 2 solenoid cable 3 solenoid card 16. Remove the six M2.5 x 8-mm screws that attach the left and right hinge arms to the computer base. 1 system board 2 M2.5 x 8-mm screws (6) 3 hinge arms (2) 17. Lift the computer base and carefully thread the solenoid and video cables through the opening in the bottom of the computer base. These cables are attached to the right hinge arm. 18.
System Board Assembly: Dell XPS M2010 Service Manual 1 video cable 2 solenoid cable 3 opening in computer base 19. Remove the frame (see Removing the Frame). 20. Remove the modem (see Removing the Modem). 21. Remove the USB/audio port board from the system board: a. Disconnect the USB/audio cable from the system board. b. Remove the four M2.5 x 5-mm screws that attach the USB/audio port board to the system board. c.
System Board Assembly: Dell XPS M2010 Service Manual 1 M2.5 x 5-mm screws 2 USB/audio port board (4) 3 black connector on USB/audio port board 4 USB/audio cable 6 black connector on system board 5 cable connector on system board 22. Disconnect the microphone cable from the system board. 23. Disconnect the keyboard cable from the system board. Pull the top of the connector out, then remove the flat cable. 24. Disconnect the subwoofer cable from the system board. 25.
System Board Assembly: Dell XPS M2010 Service Manual 1 microphone cable (JMIC) 2 keyboard cable (JKBDK) 3 subwoofer cable (JWOFR) 4 cable for internal card with Bluetooth wireless technology (JBT) 26. Remove the four M2.5 x 5-mm screws marked with white arrows on the system board. 1 arrows and M2.5 x 5-mm screws (4) 27. Pull out slightly on the back right corner of the computer base to release the connectors on the system board from the base. 28.
System Board Assembly: Dell XPS M2010 Service Manual 1. Insert the system board, slowly easing the connectors into their access holes on the back and side of the computer base. Ensure that the cables for the microphone and keyboard are not underneath the system board. 2. Replace the four M2.5 x 5-mm screws marked with white arrows on the system board. 3. Replace the USB/audio port board: a. Insert the USB/audio port board at an angle and push down on the black connector to snap the board into place. b.
System Board Assembly: Dell XPS M2010 Service Manual 26. Turn the computer over and open the display (see Opening the Display). 27. Detach the keyboard by grasping the sides of the keyboard and pulling it straight out from the computer base. NOTICE: Before turning on the computer, ensure that no stray screws remain inside the computer. Failure to do so may result in damage to the computer. 28. Turn on the computer.
Computer Base: Dell XPS M2010 Service Manual Back to Contents Page Computer Base Dell™ XPS™ M2010 Service Manual Replacing the Computer Base CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface.
Flashing the BIOS: Dell XPS M2010 Service Manual Back to Contents Page Flashing the BIOS Dell™ XPS™ M2010 Service Manual NOTICE: Plug the AC adapter into a known good power source to prevent a loss of power. Failure to do so may cause system damage. NOTE: The Service Tag is located in the battery compartment. 1. Before flashing the BIOS, follow the instructions in Before Working Inside Your Computer to remove the battery and make a note the Service Tag number. 2.
Pin Assignments for I/O Connectors: Dell XPS M2010 Service Manual Back to Contents Page Pin Assignments for I/O Connectors Dell™ XPS™ M2010 Service Manual USB Connector DVI-I Connector S-Video TV-Out Connector IEEE 1394 Connector USB Connector Pin Signal 1 USB5V+ 2 USBP– 3 USBP+ 4 GND DVI-I Connector Pin Signal Pin Signal 1 TMDS DATA2– 13 TMDS DATA3+ 2 TMDS DATA2+ 14 +5V 3 TMDS DATA2/4 SHLD 15 GND (FOR +5V) 4 TMDS DATA4– 16 HOT PLUG DETECT 5 TMDS DATA4+ 17 TMDS DATA0–
Pin Assignments for I/O Connectors: Dell XPS M2010 Service Manual 11 TMDS DATA1/3 SHLD 23 TMDS CLK+ 12 TMDS DATA3– TMDS CLK– 24 Pin Signal C1 ANALOG RED VID OUT C2 ANALOG GRN VID OUT C3 ANALOG BLU VID OUT C4 ANALOG HOR SYNC C5 ANALOG COM GND RET S-Video TV-Out Connector S-Video Pin Signal 1 GND 2 GND 3 DLUMA-L 4 DCRMA-L Composite Video Pin Signal 5 NC 6 DCMPS-L 7 GND IEEE 1394 Connector Pin Signal file:///C|/Users/santhosh_v.
Pin Assignments for I/O Connectors: Dell XPS M2010 Service Manual 1 TPB– 2 TPB+ 3 TPA– 4 TPA+ Back to Contents Page file:///C|/Users/santhosh_v.ASIA-PACIFIC/Desktop/Hawke/New%20folder/pinasign.