Instruction Manual

5
Description/Use
en
DESCRIPTION
A) Front panel
B) Washable prelter
C) HEPA lter/active carbon lter
D) Nano-silver lter (certain models only)
E) Photocatalytic lter with UVC lamp
F) Air quality sensor
G) AQS (Air Quality System) Air quality LED indicator
H) Handle
I) Filtered air outlet grille
L) Power cable with plug
M) Cable compartment
N) Control panel
O) ON/OFF
P) Fan speed
Q) AUTO speed
R) Ioniser
S) AQS (Air Quality System) air quality LED indicator on/o
T) Auto-o
U) Reset button
V) Fan speed LED display
W) LED timer (1-2-4-8 h)
X) HEPA lter exhausted LED
Y) Safety microswitch
USE
Read these instructions before using the appliance.
• Unpack the air purier and place on a stable at surface
so that the air intake in the front panel and air outlet
(top grille) are not blocked. A good position in the room
might be at least a metre from the wall.
• Remove the front panel (g. 3). Inside the purier you
will nd the prelter (B) and HEPA lter/active carbon
lter (C) and the nano-silver lter (D) (certain models
only) packed, depending on the model, in a plastic bag.
And the photocatalytic lter (E) xed to the air intake
grill.
• Removethelter(s)(dependingonthemodel)fromthe
bag, as shown in g. 2, then place them in the following
order: nano lter, with the silver side adhering to the
appliance, HEPA lter with the black active carbon side
resting directly on and adhering to the nano-silver, then
the prelter, slotting it in place as shown in g. 4.
• Replacethefrontpanel;
• Aftermakingsurethevoltageinyourhomecorresponds
to the voltage indicated on the appliance, plug the ap-
pliance into the mains socket.
• Removetheprotectivelmfromthecontrolpanel.
• TurntheapplianceonbytouchingtheON/OFFicon(O).
The corresponding icon lights up and the appliance co-
mes on automatically at minimum speed. The AUTO icon
(Q) ashes and the air quality LED indicators (G) light up
orange for 3 minutes. This time is necessary for the ap-
pliance to detect air quality, then the AUTO icon becomes
steady and the air quality LED indicators (G) change co-
lour depending on the air quality detected and also the
fan speed changes accordingly:
BAD AIR QUALITY:
orange + max. fan speed
SATISFACTORY AIR QUALITY:
green + med. fan speed
GOOD AIR QUALITY:
blue + min. fan speed
Please note: the change in colour of the air quality in-
dicator (G) is always sequential:
ORANGE <-----> GREEN <-----> BLUE
Please note: to vary the set fan speed, touch the icon
(P) corresponding to the required fan speed (Min/Med/
Max).
• TheLEDcorrespondingtotheselectedspeedlightsup.
Please note: When the appliance starts after having
been turned o, using a light pressure on the ON/OFF,
it starts with the last function set with the exception of
the auto-o function ).
“AUTO” operation (Q)
Tap the “AUTO” icon, the appliance independently decides the
fan speed according to the air quality detected (min, med,
max).
Ioniser (R)
For the release of negative ions into the environment through
puried air, touch the ioniser icon (R). The corresponding LED
lights up.
Auto-o (T)
This function can be used to turn the appliance o automati-
cally after a given period of time.
With the appliance on, touch the auto-o icon (T) to select
how many hours should elapse before the appliance goes o
(1-2-4-8 hours), the corresponding LED comes on.