User guide

Installation
Page 9Page 8
WARNING
Installation
1
2
A
C
B
To reduce the risk of fire, electrical
shock, or injury when using your
app li an c e, fo ll ow th ese ba si c
precautions:
Read all instructions before using the
Ÿ
Beverage Cabinet.
DANGER or WARNING: Risk of child
Ÿ
entrapment.
Child entrapment and suffocation are not
problems of the past. Junked or
abandoned appliances are still dangerous
. . . even if they will “just sit in the garage a
few days”.
Before you throw away your old
Ÿ
Beverage Cabinet: Take off the door.
Leave the shelves in place so that children
may not easily climb inside
Never allow children to operate, play with,
Ÿ
or crawl inside the appliance.
Never clean appliance parts with
Ÿ
flammable fluids. The fumes can create a
fire hazard or explosion.
Do not store or use gasoline or any other
Ÿ
flammable vapors and liquids in the
vicinity of this or any other appliance. The
fumes can create a fire hazard or
explosion.
Before using your Beverage Cabinet
Remove the exterior and interior packing.
Ÿ
Check to be sure you have all of the
Ÿ
following parts:
- 1 x Glass Shelf
- 2 x Wire Shelves
- 2 x Keys
- 1 x Stainless Steel Handle Assembly
with Hardware
- 2 x Decorative Screws.
- 1 x Instruction Manual.
Before connecting the Beverage Cabinet
Ÿ
to the power source, let it stand upright for
approximately 2 hours. This will reduce
the possibility of a malfunction in the
cooling system from handling during
transportation.
Clean the interior surface with lukewarm
Ÿ
water using a soft cloth.
Install the handle on the left side of the
Ÿ
door.
Installation of your Beverage Cabinet
This appliance is designed to be for free
Ÿ
standing installation or built-in (fully
recessed).
Place your Beverage Cabinet on a floor
Ÿ
that is strong enough to support it when it
is fully loaded. To level your Beverage
Cabinet, adjust the front levelling legs at
the bottom of the Beverage Cabinet.
Locate the Beverage Cabinet away from
Ÿ
direct sunlight and sources of heat (stove,
heater, radiator, etc.). Direct sunlight may
affect the acrylic coating and heat sources
may increase electrical consumption.
Extreme cold ambient temperatures may
also cause the unit not to perform
properly.
Avoid locating the unit in moist areas.
Ÿ
Plug the Beverage Cabinet into an
Ÿ
exclusive, properly installed-grounded
wall outlet. Do not under any
circumstances cut or remove the third
(ground) prong from the power cord. Any
questions concerning power and/or
grounding should be directed toward a
certified electrician or an authorised
service center.
Reversing the Door Swing of Your
Appliance
This appliance has the capability of the
Ÿ
door opening from either the left or right
side. The unit is delivered to you with the
door opening from the left side. Should
you desire to reverse the opening
direction, please call service for reversal
instructions.
Installing stainless steel handle
This Beverage Cabinet includes a stainless
steel handle that is not required to operate
this unit.
To install the handle please follow the below
instructions:
For your convenience the screws used in the
installation of the handle have been put in
place at the factory.
Pull away the door gasket (A) in the area
Ÿ
where the handle is to be installed on the
left side as in Illustration #1. The gasket is
easily displaced by hand, no tools are
necessary.
Align the handle (B) with the screws
Ÿ
installed. Tighten the screws (C) using a
Phillips head screwdriver until the handle
sets both flush and secured tightly
against the door frame. (DO NOT over
tighten as this will cause damage to the
handle assembly).
Replace the door gasket (A) to its original
Ÿ
position.
If you choose not to use the handle
Ÿ
supplied, simply follow step 1 to access
the installation screws and remove them
and then place the two decorative plugs
into the two holes separately. Continue on
to step 3 to replace the door gasket to its
original position.
Clearances
Clearances required for the Beverage
Ÿ
Cabinet to adjacent surfaces are 10mm
from top and sides, and 50mm from rear.
°C
°F
°F/
°C
10mm
(from sides)
10mm
(from top)
50mm
(from rear)