INSTALLATION and SERVICE INSTRUCTIONS USE and CARE INSTRUCTIONS DEH60S DEH60W ELECTRIC COOKTOPS distributed by DèLonghi Pty Ltd
INSTALLATION CAUTION: ■ In order to avoid a hazard this appliance must be installed according to these instructions for installation. WARNING: ■ ■ ■ ■ ■ ■ ■ This appliance is to be installed only by an authorised person. This appliance must be used only for the task it has explicitly been designed for, that is for cooking foodstuffs. Any other form of usage is to be considered as inappropriate and therefore dangerous. Do NOT place combustible materials or products on this appliance at any time.
This cooktop has been designed and constructed in accordance with the following codes and specifications: AS/NZS 60335-1 General Requirements for Domestic electrical appliances AS/NZS 60335-2-6 Particular Requirements for Domestic electrical cooking appliances AS/NSZ 1044 Electromagnetic Compatibility Requirements. Figure 1 580 47 0 65 m in . 500 50 min 550 CLEARANCES: Installation clearances and protection of combustible surfaces shall comply with page 4.
The installation shall comply with the dimensions in Figures 1 and 2, bearing in mind that: ■ A minimum clearance of 30 mm has to be kept between the bottom of the cooking hob and the top of an appliance or a thermal barrier (see next page). ■ Overhead clearances - In no case shall the clearance between the highest part of the hob and a range hood be less than 600 mm.
THERMAL BARRIER INSTALLATION: Warning: ■ If the hob is installed over drawers or cupboards, a thermal protection barrier must be fitted at least 30 mm beneath the base of the hob (see Figure 3). Note: 1. Above not applicable if hob is mounted directly above an oven 2. For access to the hob for servicing or installation, ensure that the barrier can be removed from beneath by the use of a tool. 3. A gap of 20 mm may be allowed at rear for electrical connection and ventilation.
INSTALLATION 1. Spread out the gasket “C” over the workbench at the edge of the cut out taking care to overlap the gasket at the corners. 2. Slot in the cooking hob into the cut out of the workbench and locate it correctly. 3. Adjust the clamps “A” and tighten the screws “B” until the hob is firmly secured. 4. Using a sharp tool, trim any excess gasket which protrudes from the edge of the hob. Take care not to damage the countertop. Figure 4 6 A 40 mm max. B 20 mm min.
ELECTRICAL REQUIREMENTS Warning: ■ THIS APPLIANCE MUST BE EARTHED. ■ In order to avoid a hazard this appliance must be installed according to these instructions for installation. Caution: ■ ■ If the supply cord is damaged it must be replaced by the manufacturer or it’s Service Agent or a similarly qualified person in order to avoid a hazard. ■ Ensure that the power outlet is properly earthed before connecting the appliance. ■ Disconnect power before servicing the appliance.
FEEDER CABLE CONNECTION To connect the feeder cable to the cooking hobs with electrical plates or to replace, if necessary, some electrical part, it is necessary to: ■ ■ ■ ■ ■ ■ ■ Upturn the hob Unscrew screws “A” and remove protection “B” (fig. 5) Insert connecting plates “C” into terminal block “D” (fig. 7) as shown in the diagram in fig. 6 Unscrew cable clamp “E” (fig.
FEEDER SPECIAL CABLE SECTION Type “HO5V2V2-F” Figure 6 220-240 V 1 2 resistance to temperatures of 90°C 220-240 V ~ 50 Hz 3 x 2,50 mm2 380-416 V 3N ~ 50 Hz 5 x 1,50 mm2 380-416 V 2N ~ 50 Hz 4 x 1,50 mm2 220-240 V 3 ~ 50 Hz 4 x 2,50 mm2 50 Hz 3 4 5 PE L1 N (L 2) 380-416 V 3N 1 2 50 Hz 3 4 5 PE Figure 7 L1 L2 L3 N 380-416 V 2N 1 2 50 Hz 3 4 5 PE L1 N 1 L2 2 3 4 5 D 220-240 V 3 1 2 50 Hz 3 4 5 C PE L1 L2 L3 C 9
ELECTRIC DIAGRAM Figure 8 M T P1 P2 1 2 4 3 1 2 4 3 F1 5 4 7 P1 3 2 1 P3 9 P2 5 4 7 P1 3 2 1 ELECTRIC DIAGRAM KEY F1/2/3/4 S1 P1 P2 P3 P4 M T 10 P4 1 2 4 3 F3 F2 P3 9 P2 P3 1 2 4 3 Electric plate commutators Line pilot lamp Electric plate 2000W -230V Electric plate 1500W-230V Electric plate 1500W-230V Electric plate 1000W-230V Terminal block Earth connection F4 P3 9 P2 5 4 P3 9 P2 5 4 7 P1 3 2 1 7 P1 3 2 1 S1
USE and CARE CAUTION: ■ ■ ■ ■ ■ This appliance must be used only for the task it has explicitly been designed for, that is for cooking foodstuffs. Any other form of usage is to be considered as inappropriate and therefore dangerous. Do NOT place combustible materials or products on this appliance at any time. Do NOT spray aerosols in the vicinity of this appliance while it is in use. The appliance is not intended for use by young children or infirm persons without supervision.
■ Important: Before using the hob for the first time, it is necessary to burn off the appliance to dry off the plates and remove any protective coatings that may still be on the plates. To do this, boil a saucepan of water on each plate for about 10 minutes. There may be a strong odour and a light smoke visible during this process. This will cease when the process is complete. 1. Make sure that all the controls are turned to zero. 2. Switch on the electricity. 3. Turn the knob for the ring you require.
COOKING HINTS: ■ Be careful not to place any wet or steamed up lids on an unused hotplate, as this will lead to rust. ■ Pans should have a thick flat base to be effective. Check the base of the pan with a ruler. It should be either the same size or slightly larger than the hotplate. ■ The plates with a red dot in the middle heat up 30% faster than those without. ■ Do not use decorative covers over the hotplates as these hold condesation and could be dangerous if the hob was accidentally turned on.
■ Please note that these are only guidelines, you will quickly learn from experience which setting is correct for your needs. ECONOMIC COOKING ■ The electric plate retains heat, so you may find that you can switch off the heat 5 minutes before you finish cooking. ■ To reduce the cooking time, the plate can be set to the maximum setting at the beginning. It can then be reduced later. CLEANING AND MAINTENANCE ■ Before you begin cleaning you must ensure that the hob is switched off.
TROUBLESHOOTING: If you acquire a problem with your hob, check the following points before calling an engineer. 1. The power is switched on. 2. The controls are switched on. 3. Both the fuse and the mains fuse are intact. Servicing the appliance: Service may be obtained from your local Authorised Service Centre. Descriptions and illustrations in this booklet are given as simply indicative.
cod.