Technical data
11
To prepare the Cappuccino: press button .
To prepare the latte macchiato: press button
.
"GUFS IBWJOH EFMJWFSFE UIF GSPUIFE NJML UIF NBDIJOF
automatically prepares the coee.
Please note!
t 'PSBIPUUFSDBQQVDDJOPJUJTBEWJTFEUPQSFTTUIF$-&"/
button to heat the ducts of the milk frother device (see
successive paragraph).
t 5P QSFQBSF UIF DBQQVDDJOP PS UIF MBUUF NBDDIJBUP UIF
BQQMJBODF QFSGPSNT EFMJWFSJFT öSTU UIF NJML BOE
subsequently the coee. If wanting to interrupt the
delivery in progress, press the previously pressed button.
t 0ODF EFMJWFSZ JT DPNQMFUFE JG XBOUJOH UP JODSFBTF UIF
amount of milk or coee inside the cup, keep the button
(within a few seconds) relative to the preparation in
progress pressed.
t %POPUMFBWFUIFNJMLDPOUBJOFSPVUPGUIFSFGSJHFSBUPSGPS
too long: the higher the milk temperature (5°C is ideal),
the poorer is the quality of the froth
Cleaning the milk frother device using the CLEAN
button
After every use of the milk functions, perform cleaning to
eliminate the milk residues as follows:
1. Leave the milk container inserted in the machine (it is not
necessaryUPFNQUZUIFNJMLDPOUBJOFS
2. Place a cup or other container under the frothed milk
spout tube.
,FFQUIFi$-&"/wCVUUPOöH QSFTTFEMJHIUT
and ash. When the lights stop ashing and the
appliance goes back to ready for use, release the “CLEAN”
button: the steam cleans the circuits inside the milk
frother.
Program the amount of coee and milk in the cup for
cappuccino or milk
The machine has been set by default to deliver standard
amounts. If wanting to amend these quantities, proceed as
follows:
1. Place a cup under the spouts of the coee spout and under
the milk spout tube.
2. Press the button relative to the preparation with milk to
be programmed and keep it pressed. After a few seconds,
the machine starts delivering the milk.
3. As soon as the wanted amount of milk in cup is reached,
release the button milk delivery stops.
1SPHSBNUIFBNPVOUPGDPòFFJODVQBTGPSUIFBNPVOUPG
milk.
1SPHSBNNJOH JT DPOöSNFE CZ UIF MJHIUT øBTIJOH GPS
seconds.
The machine is now re-programmed according to the new
amounts of milk and coee.
Preparing the hot water
Scalding hazard!
Do not leave the machine unattended when delivering hot
water. The spout heats up during delivery therefore, only the
black part must be held.
$IFDLUIFIPUXBUFSTQPVUJTDPSSFDUMZBUUBDIFEöH
2. Place a cup under the spout (as near as possible to avoid
sprays).
3. Press the
CVUUPOöHUIFSFMBUJWF MJHIU øBTIFT
and the appliance starts hot water delivery.
5IFNBDIJOFBVUPNBUJDBMMZTUPQTEFMJWFSZ
Please note!
t 5PNBOVBMMZJOUFSSVQUUIFIPUXBUFSEFMJWFSZQSFTT
button again.
Programming the amount of water automatically
delivered
If wanting to amend the set by default amount, proceed as
follows:
1. Place a cup under the spout.
2. Keep the
button pressed.
3. When the hot water in the cup reaches the required level,
SFMFBTF UIF CVUUPO 1SPHSBNNJOH JT DPOöSNFE CZ UIF
lights ashing for three seconds.
The machine is now re-programmed according to the new
amount.
Cleaning
Attention!
t %P OPU VTF TPMWFOUT BCSBTJWF EFUFSHFOUT PS BMDPIPM UP
clean the machine.
t 0OMZ UIF NJML DPOUBJOFS % DBO CF XBTIFE JO UIF EJTI
washer. No other part of the appliance can be washed in
the dishwasher.
t %P OPU VTF NFUBM PCKFDUT UP SFNPWF DPòFF EFQPTJUT
or fouling as they might scratch the metal or plastic
surfaces.
en
Instructions for use