5713221861/10.
BEAN TO CUP ESPRESSO AND DE CAPPUCCINO MACHINE Instruction for use GB ECAM28.
B B2 B3 B4 B5 B6 B1 B7 B13 B8 B9 C B10 B11 B12 D D1 D2 C1 A18 C3 C2 D3 D4 C4 D5 22 D6
A A1 A2 A5 A3 A6 A4 A11 A12 A7 A13 A8 A14 A9 A15 A16 A10 A22 A18 A17 A20 A19 A21 33
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 44
17 18 19 20 21 22 23 24 25 26 27 28 B SH A PU SH PU 29A B 29B 30 31 55 32 A
CONTENTS Making coffee using coffee beans..................................12 Making coffee using pre-ground coffee.........................13 INTRODUCTION........................................................ 7 Symbols used in these instructions..................................7 Letters in brackets............................................................7 Troubleshooting and repairs............................................7 MAKING DRINKS WITH MILK...................................
INTRODUCTION • Thank you for choosing this automatic espresso and cappuccino machine. We hope you enjoy using your new appliance. Take a few minutes to read these instructions. This will avoid all risks and damage to the machine. • • • Symbols used in these instructions Important warnings are identified by these symbols. It is vital to respect these warnings. • Danger! Failure to observe the warning could result in life threatening injury from electric shock.
B10. FLAT WHITE button: to deliver a flat white B11. HOT MILK button: to deliver a cup of hot milk (When in the settings menu, press to scroll forwards) B12: button: to deliver steam B13. button: to make 2 cups of coffee with the settings displayed Please note: Keep these instructions. If the appliance is passed to other persons, they must also be provided with these instructions. DESCRIPTION Description of the milk container (page 2 - C ) D1. Froth adjustment and CLEAN dial D2.
Connecting the appliance • Important! Check that the mains power supply voltage corresponds to the value indicated on the rating plate on the bottom of the appliance. Connect the appliance to an earthed and correctly installed socket with a minimum current rating of 10A only. If the power socket does not match the plug on the appliance, have the socket replaced with a suitable type by a qualified professional.
• Auto-start You can set the auto-start time in order to have the appliance ready at a certain time (for example in the morning) so you can make coffee immediately. release the main switch at the side of the appliance (fig. 2). Important! Never press the main switch while the appliance is on. Please note! To enable this function, the time must already have been set correctly.
Beep This enables or disables the beep emitted by the machine each time the buttons are pressed or an accessory is inserted/ removed. The beep is enabled by default. To disable or re-enable the beep, proceed as follows: 1. Press the MENU/ESC button to enter the menu; 2. Press the HOT MILK or LATTE button (fig. 8) until “Beep” is displayed; 3. Press the button. “ Disable?” or “ Enable?” is displayed; 4. Press the button to enable or disable the beep; 5. Press the MENU/ESC button to exit the menu. 3.
5. Press the To modify this quantity, proceed as follows: 1. Place a cup under the coffee spouts (fig. 14). 2. Press the button (fig. 10) until “MY COFFEE” is displayed. 3. Keep the button (fig. 11) pressed until the message “1 MY COFFEE Program quantity” is displayed and coffee delivery begins. Release the button. 4. As soon as the coffee in the cup reaches the required level, press the button (fig. 11) again. The quantity of coffee in the cup has now been programmed. button to confirm and exit.
2. Place under the coffee dispensing spouts, either: - 1 cup if you want one coffee (fig. 14); - 2 cups if you want 2 coffees. 3. Lower the spouts as near as possible to the cup. This makes a creamier coffee (fig. 15). 4. Press the button corresponding to the number of coffees required (1 cup or 2 cups , figs. 11 and 16). 5. Preparation begins. The amount of coffee selected is displayed together with a progress bar which gradually fills as preparation progresses. 2.
Adjusting the amount of froth Turn the froth adjustment dial on the milk container lid to adjust the amount of froth on the milk delivered while making drinks with milk. Dial position Description Recommended for… No froth LATTE/ HOT MILK Min. froth FLAT WHITE Max. froth CAPPUCCINO/ HOT MILK (FROTHED MILK) “SET DIAL TO CLEAN” flashes on the display each time you use a milk function. To eliminate all milk residues, proceed as follows: 1.
The spout becomes hot during delivery. Hold by the handle only. • • Please note! If “Energy Saving” mode is enabled, you may have to wait a few seconds before the hot water or steam is delivered. • Delivering hot water 1. Make sure the hot water spout is attached correctly (fig. 6). 2. Place a container under the spout (as close as possible to avoid splashes). 3. Press the button (fig. 3). “Hot water” is displayed, together with a progress bar which fills gradually as preparation proceeds. 4.
Cleaning the water tank 1. Clean the water tank (A17) regularly (about once a month and whenever you replace the water softener filter (if provided) with a damp cloth and a little mild washing up liquid. 2. Remove the filter (if present) and rinse with running water. 3. Replace the filter (if provided), fill the tank with fresh water and replace the tank. If you make a number of cappuccinos one after the other, the metal cup tray becomes hot.
6. Check that the intake tube and spout are not clogged with milk residues. 7. Replace the dial (in correspondence to the word “INSERT”), spout and milk intake tube. 8. Place the lid back on the milk container. Please note! If the infuser is difficult to insert, before insertion, adapt it to the right size by pressing the two levers shown in the figure.
8. Place an empty container with a minimum capacity of 1.5 litres under the hot water spout (fig. 4). soft water l Important! Danger of burns Hot water containing acid flows from the spout. Avoid contact with splashes of water. 9. Press the button to confirm that you have added the solution. The message “Descale underway” is displayed. The descale programme starts and the descaler liquid comes out of the water spout.
the openings at the side 35 for more than a minute (fig. 34). 4. Extract the tank from the appliance and fill with water. 5. Insert the filter in the water tank and immerse it completely for about ten minutes, sloping it to 36A enable the air bubbles to escape (fig. 35). 6. Insert the filter in the filter housing and press as far as it will go (fig. 36A) 7. Close the tank with the 36B lid, then put the tank back in the machine (fig. 36B).
DISPLAYED MESSAGES DISPLAYED MESSAGE POSSIBLE CAUSE SOLUTION FILL TANK Insufficient water in the tank. Fill the tank with water and/or insert it correctly, pushing it as far as it will go until it clicks into place. EMPTY GROUNDS CONTAINER The grounds container (A22) is full. Empty the grounds container and drip tray, clean and replace. Important: when removing the drip tray, the grounds container must be emptied, even if it is not completely full.
GENERAL ALARM The inside of the appliance is very dirty. Clean the inside of the appliance thoroughly, as described in the section “Cleaning and maintenance”. If the message is still displayed after cleaning, contact a service centre. EMPTY CIRCUIT FILL CIRCUIT alternating with Hot water press OK The water circuit is empty. Press OK to deliver water from the spout (A14) until it flows out normally. REPLACE FILTER The water filter is exhausted.
Coffee does not come out of one of the spouts. The spouts are blocked. Clean the spouts with a toothpick (fig. 29B). The milk does not The milk container lid is dirty. come out of the milk spout. Clean the milk container lid as described in the section “Cleaning the milk container”. The milk contains large bubbles and squirts out of the milk spout or there is little froth . Clean the milk container lid as described in the section “cleaning the milk container”. the milk container lid is dirty.
ELECTRICAL CONNECTION (UK ONLY) Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt about your supply contact your local electricity company. The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity. Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure outlined below.