Instruction Manual

19
3. To activate the lter, run tap water through the hole in the
lter as shown in the gure until water comes out of the
openings at the side for more than a minute (g. 37);
4. Extract the tank (A10) from the appliance and ll with
water;
5. Insert the lter in the water tank and immerse it com-
pletely for about ten seconds, sloping it to enable the air
bubbles to escape (g. 38);
38
39B
39A
6. Insert the lter in its housing (g. 39A) and push down as
far as it will go; soft water slightly hard water hard water
very hard water
7. Close the tank with the lid (g. 39B), then replace the tank
in the appliance;
When you install the lter, you must notify the appliance of its
presence.
8. Press the MENU button (B3) to enter the menu;
9. Press the (B4) or (B5) button repeatedly until
“Install lter” appears on the display (B1);
10. Press the button (B6);
11. “Enable?” appears on the display;
12. Press the button to conrm the selection. “HOT
WATER Conrm?” appears on the display;
13. Position a container under the hot water spout (C6) (min.
capacity: 500ml);
14. Press the button to conrm the selection. The ap-
pliance begins hot water delivery and the message “Please
wait...” appears on the display;
15. After the ow of hot water stops, the appliance automatically
resets to “Ready for coee” status.
The new lter is active and indicated by an asterisk displayed
under “Install lter” in the menu. You can now use the appliance.
17.2 Replacing the lter
When “REPLACE FILTER” appears on the display (B1), after two
months (see date indicator) or when the appliance has not been
used for 3 weeks, you should replace the lter (C4):
1. Extract the tank (A10) and exhausted lter;
2. Take the new lter out of its packet and proceed as illus-
trated in points 3, 4, 5 and 6 in the previous section;
3. Position a container under the hot water spout (C6) (min.
capacity: 500ml);
4. Press the MENU button (B3) to enter the menu;
5. Press the (B4) or (B5) button repeatedly until
“Replace lter” appears on the display (B1);
6. Press the button (B6);
7. The message “Conrm?” appears on the display;
8. Press the button to conrm the selection;
9. “HOT WATER Conrm?” appears on the display;
10. Press the button to conrm the selection. The ap-
pliance begins hot water delivery and the message “Please
wait...” appears on the display;
11. After the ow of hot water stops, the appliance automati-
cally resets to “Ready for coee” status.
The new lter is now active and you can use the coee machine.
17.3 Removing the lter
If you want to use the appliance without the lter (C4), you
must remove it and notify the appliance of its removal. Proceed
as follows:
1. Extract the tank (A10) and exhausted lter;
2. Press the MENU button (B3) to enter the menu;
3. Press the (B4) or (B5) button repeatedly until
“Remove lter *” appears on the display (B1);
4. Press the button (B6);
5. The message “Conrm?” appears on the display;
6. Press the button to conrm and the MENU button to
exit the menu.
18. TECHNICAL DATA
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1450W
Pressure: 1,5 MPa (15 bar)
Max. water tank capacity: 1,8 l
Dimensioni LxDxH : 240x430x350 mm
Cord length: 1750 mm
Weight: 9,6 Kg
Max. beans container capacity: 250 g
Max. beans container capacity:
• European Standby Regulation 1275/2008
• Materials and accessories coming into contact with food
conform to EEC regulation 1935/2004.
19. DISPOSAL
The appliance must not be disposed of with house-
hold waste, but taken to an authorised waste separa-
tion and recycling centre.