User Manual

18
6. To descale the appliance later, press ESC (B5). The symbol
on the display reminds you that the appliance needs descaling.
To access the descaling menu:
1. Turn the appliance on and wait until it is ready for use;
2. Press (B6) to enter the "Settings" menu;
3. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two lines. Press OK (B3);
4. Press OK to select "Descale";
5. Conrm? (∼45 minutes)”. Press OK to conrm;
6. "Remove lter": extract the water tank (A17), remove the
water softener lter (C4) (if present) and empty the water
tank. Press OK;
7. "Pour descaler and water into tank": Pour the descaler into
the tank up to level A (corresponding to a 100 ml pack)
marked on the inner surface of the tank, then add water
(1 litre) up to level B (g. 32) and put the water tank back.
Press OK;
8. "Empty drip tray": Remove, empty and replace the drip
tray (A15) and grounds container (A11). Press OK;
9. "Place 1.8L container empty under spouts": Place an empty
container with a minimum capacity of 1.8 litres under the hot
water spout (C6) and coee spouts (A9) (g. 33). Press OK ;
1,8 l
33
Important! Danger
of burns
Hot water containing acid
ows out of the coee spouts
and hot water spout. Take
care to avoid contact with
splashes of this solution.
10. "Descaling underway":
The descale programme
starts and the descaler liq-
uid comes out of the hot
water and coee spouts. A series of rinses and pauses is
performed automatically to remove all the scale residues
inside the coee machine;
After about 25 minutes, descaling stops;
11. "Rinse tank and ll with water": the appliance is now
ready to rinse with fresh water. Empty the container used
to collect the descaler solution. Extract the water tank,
empty, rinse under running water, ll with fresh water up
to the MAX level and put back in the appliance. Press OK;
12. "Place 1.8L container empty under spouts": place the con-
tainer used to collect the descaler solution empty under
the coee spouts and hot water spout (g. 33) and press
OK";
13. "Rinsing Conrm?": press OK;
6. Use the brush (C5) to remove any coee residues left in the
infuser housing, visible through the infuser door;
7. After cleaning, replace the infuser by sliding it onto the in-
ternal support, then push the PUSH symbol fully in until it
clicks into place;
Please note:
If the infuser is dicult to insert, before insertion, adapt it to the
right size by pressing the two levers (g. 27).
8. Once inserted, make sure the two coloured buttons have
snapped out;
9. Close the infuser door;
10. Put the water tank back.
14.10 Cleaning the milk container
Clean the milk container (D) each time you prepare milk as de-
scribed below:
1. Remove the lid (D2);
2. Remove the milk spout (D5) and intake tube (D4) (g. 28);
3. Turn the froth adjustment dial (D1) anticlockwise to the
"INSERT" position (g. 29) and pull o upwards;
4. Wash all the components thoroughly with hot water and
mild washing-up liquid. All components are dishwasher
safe, placing them in the top basket of the dishwasher.
Make sure there are no milk residues on the hollow and
groove under the dial (g. 30). If necessary, scrape the
groove with a toothpick;
5. Rinse inside the froth adjustment dial seat with running
water (g. 31);
6. Check that the intake tube and milk spout are not clogged
with milk residues;
7. Replace the dial (in correspondence to the word "INSERT"),
spout and milk intake tube;
8. Place the lid back on the milk container (D3).
14.11 Cleaning the hot water nozzle
Each time you prepare milk, clean the connection nozzle (A8)
with a sponge to remove milk residues from the gaskets (g.
20).
15. DESCALING
Important!
• Before use, read the instructions and the labelling on the
descaler pack.
• You should use De’Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may re-
sult in faults not covered by the manufacturer's guarantee.
Descale the machine when "Descale, ESC to cancel, OK to des-
cale (∼45 minutes)" appears on the display (B1). To descale im-
mediately, press OK (B3) and follow the instructions from point