Instruction Manual

10
• release the main switch at the back of the appliance (g.
2).
Important!
Never press the main switch while the appliance is on.
MENU SETTINGS
When you access the settings menu by pressing the MENU/ESC
button, scroll the menu items by pressing < or > (g. 9).
Rinsing
Use this function to deliver hot water from the spout to heat the
internal circuit and make the coee delivered hotter.
To enable the function, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (g. 9) until “Rinsing” is displayed;
3. Press the button: “Conrm?” will be displayed.
4. Press the button (g. 3): after a few seconds, hot
water ows out of the spout, heating the internal circuit
and making the coee delivered hotter.
Please note!
Press any button to stop hot water delivery at any time.
Descaling
For instructions on descaling, see page 16.
Install lter
For instructions on how to install the lter, see the section
“Water softener lter” (page 17).
Replacing the lter (if installed)
For instructions on how to replace the lter, see the section “Re-
placing the lter” (page 10).
Adjust time
To adjust the time on the display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (g. 9) until “Adjust time” is displayed;
3. Press the button (g. 3): the hours ash;
4. Press < or > (g. 9) to change the hours;
5. Press the button to conrm: the minutes ash;
6. Press < or > (g. 9) to change the minutes;
7. Press the button to conrm.
This sets the time. Press the MENU/ESC button to exit the menu.
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coee immediately.
Please note!
To enable this function, the time must already be set correctly.
To enable auto-start, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (g. 9) until “Auto-start” is displayed;
3. Press the button. “Enable?” is displayed;
4. Press the button to conrm;
5. Press < or > to choose the hours;
6. Press the button to conrm;
7. Press < or > (g. 9) to change the minutes;
8. Press the button to conrm;
9. Then press the MENU/ESC button to exit the menu.
Once the time has been conrmed, activation of auto-start is
indicated by the symbol displayed under the menu item
and alongside the time.
To disable the function:
1. Select auto-start from the menu;
2. Press the button. “Disable?” is displayed;
3. Press the button to conrm.
The symbol is no longer displayed.
Auto-O (standby)
Auto-o mode can be set, so that the appliance switches o
when not used for 15 or 30 minutes, or 1, 2 or 3 hours.
To programme Auto-o, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (g. 9) until “Auto-o” is displayed;
3. Press the button;
4. Press < or > (g. 9) until the required operating time (15
or 30 minutes, or 1, 2 or 3 hours) is displayed;
5. Press the button to conrm;
6. Then press the MENU/ESC button to exit the menu.
Auto-o is programmed.
Energy saving
Use this function to enable or disable energy saving.
When enabled, the function reduces energy consumption in
compliance with European regulations.
To disable (or enable) energy saving, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (g. 9) until “Energy saving” is displayed;
3. Press the button. “Disable?” is displayed (or “Ena-
ble?” if the function has been disabled);
4. Press the button to disable (or enable) energy sav-
ing mode;
5. Then press the MENU/ESC button to exit the menu.
When the function is active, if the machine is not used for some
time, “Energy saving” is displayed.